| // SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| |
| /dts-v1/; |
| |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/pinctrl/rockchip.h> |
| #include <dt-bindings/soc/rockchip,vop2.h> |
| #include "rk3566.dtsi" |
| |
| / { |
| model = "Pine64 Quartz64 Model A"; |
| compatible = "pine64,quartz64-a", "rockchip,rk3566"; |
| |
| aliases { |
| ethernet0 = &gmac1; |
| mmc0 = &sdmmc0; |
| mmc1 = &sdhci; |
| }; |
| |
| chosen: chosen { |
| stdout-path = "serial2:1500000n8"; |
| }; |
| |
| gmac1_clkin: external-gmac1-clock { |
| compatible = "fixed-clock"; |
| clock-frequency = <125000000>; |
| clock-output-names = "gmac1_clkin"; |
| #clock-cells = <0>; |
| }; |
| |
| fan: gpio_fan { |
| compatible = "gpio-fan"; |
| gpios = <&gpio0 RK_PD5 GPIO_ACTIVE_HIGH>; |
| gpio-fan,speed-map = |
| < 0 0>, |
| <4500 1>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&fan_en_h>; |
| #cooling-cells = <2>; |
| }; |
| |
| hdmi-con { |
| compatible = "hdmi-connector"; |
| type = "a"; |
| |
| port { |
| hdmi_con_in: endpoint { |
| remote-endpoint = <&hdmi_out_con>; |
| }; |
| }; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| |
| led-work { |
| label = "work-led"; |
| default-state = "off"; |
| gpios = <&gpio0 RK_PD3 GPIO_ACTIVE_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&work_led_enable_h>; |
| retain-state-suspended; |
| }; |
| |
| led-diy { |
| label = "diy-led"; |
| default-state = "on"; |
| gpios = <&gpio0 RK_PD4 GPIO_ACTIVE_HIGH>; |
| linux,default-trigger = "heartbeat"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&diy_led_enable_h>; |
| retain-state-suspended; |
| }; |
| }; |
| |
| rk817-sound { |
| compatible = "simple-audio-card"; |
| simple-audio-card,format = "i2s"; |
| simple-audio-card,name = "Analog RK817"; |
| simple-audio-card,mclk-fs = <256>; |
| |
| simple-audio-card,cpu { |
| sound-dai = <&i2s1_8ch>; |
| }; |
| |
| simple-audio-card,codec { |
| sound-dai = <&rk817>; |
| }; |
| }; |
| |
| sdio_pwrseq: sdio-pwrseq { |
| compatible = "mmc-pwrseq-simple"; |
| clocks = <&rk817 1>; |
| clock-names = "ext_clock"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&wifi_enable_h>; |
| post-power-on-delay-ms = <100>; |
| power-off-delay-us = <5000000>; |
| reset-gpios = <&gpio2 RK_PC2 GPIO_ACTIVE_LOW>; |
| }; |
| |
| spdif_dit: spdif-dit { |
| compatible = "linux,spdif-dit"; |
| #sound-dai-cells = <0>; |
| }; |
| |
| spdif_sound: spdif-sound { |
| compatible = "simple-audio-card"; |
| simple-audio-card,name = "SPDIF"; |
| |
| simple-audio-card,cpu { |
| sound-dai = <&spdif>; |
| }; |
| |
| simple-audio-card,codec { |
| sound-dai = <&spdif_dit>; |
| }; |
| }; |
| |
| vcc12v_dcin: vcc12v_dcin { |
| compatible = "regulator-fixed"; |
| regulator-name = "vcc12v_dcin"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <12000000>; |
| regulator-max-microvolt = <12000000>; |
| }; |
| |
| /* vbus feeds the rk817 usb input. |
| * With no battery attached, also feeds vcc_bat+ |
| * via ON/OFF_BAT jumper |
| */ |
| vbus: vbus { |
| compatible = "regulator-fixed"; |
| regulator-name = "vbus"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| vin-supply = <&vcc12v_dcin>; |
| }; |
| |
| vcc3v3_pcie_p: vcc3v3-pcie-p-regulator { |
| compatible = "regulator-fixed"; |
| enable-active-high; |
| gpio = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pcie_enable_h>; |
| regulator-name = "vcc3v3_pcie_p"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| vin-supply = <&vcc_3v3>; |
| }; |
| |
| vcc5v0_usb: vcc5v0_usb { |
| compatible = "regulator-fixed"; |
| regulator-name = "vcc5v0_usb"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| vin-supply = <&vcc12v_dcin>; |
| }; |
| |
| /* all four ports are controlled by one gpio |
| * the host ports are sourced from vcc5v0_usb |
| * the otg port is sourced from vcc5v0_midu |
| */ |
| vcc5v0_usb20_host: vcc5v0_usb20_host { |
| compatible = "regulator-fixed"; |
| enable-active-high; |
| gpio = <&gpio4 RK_PB5 GPIO_ACTIVE_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&vcc5v0_usb20_host_en>; |
| regulator-name = "vcc5v0_usb20_host"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| vin-supply = <&vcc5v0_usb>; |
| }; |
| |
| vcc5v0_usb20_otg: vcc5v0_usb20_otg { |
| compatible = "regulator-fixed"; |
| enable-active-high; |
| gpio = <&gpio4 RK_PB5 GPIO_ACTIVE_HIGH>; |
| regulator-name = "vcc5v0_usb20_otg"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| vin-supply = <&dcdc_boost>; |
| }; |
| |
| vcc3v3_sd: vcc3v3_sd { |
| compatible = "regulator-fixed"; |
| gpio = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&vcc_sd_h>; |
| regulator-boot-on; |
| regulator-name = "vcc3v3_sd"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| vin-supply = <&vcc_3v3>; |
| }; |
| |
| /* sourced from vbus and vcc_bat+ via rk817 sw5 */ |
| vcc_sys: vcc_sys { |
| compatible = "regulator-fixed"; |
| regulator-name = "vcc_sys"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <4400000>; |
| regulator-max-microvolt = <4400000>; |
| vin-supply = <&vbus>; |
| }; |
| |
| /* sourced from vcc_sys, sdio module operates internally at 3.3v */ |
| vcc_wl: vcc_wl { |
| compatible = "regulator-fixed"; |
| regulator-name = "vcc_wl"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| vin-supply = <&vcc_sys>; |
| }; |
| }; |
| |
| &combphy1 { |
| status = "okay"; |
| }; |
| |
| &combphy2 { |
| status = "okay"; |
| }; |
| |
| &cpu0 { |
| cpu-supply = <&vdd_cpu>; |
| }; |
| |
| &cpu1 { |
| cpu-supply = <&vdd_cpu>; |
| }; |
| |
| &cpu2 { |
| cpu-supply = <&vdd_cpu>; |
| }; |
| |
| &cpu3 { |
| cpu-supply = <&vdd_cpu>; |
| }; |
| |
| &cpu_thermal { |
| trips { |
| cpu_hot: cpu_hot { |
| temperature = <55000>; |
| hysteresis = <2000>; |
| type = "active"; |
| }; |
| }; |
| |
| cooling-maps { |
| map1 { |
| trip = <&cpu_hot>; |
| cooling-device = <&fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| }; |
| }; |
| |
| &gmac1 { |
| assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru SCLK_GMAC1>; |
| assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru SCLK_GMAC1>, <&gmac1_clkin>; |
| clock_in_out = "input"; |
| phy-supply = <&vcc_3v3>; |
| phy-mode = "rgmii"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&gmac1m0_miim |
| &gmac1m0_tx_bus2 |
| &gmac1m0_rx_bus2 |
| &gmac1m0_rgmii_clk |
| &gmac1m0_clkinout |
| &gmac1m0_rgmii_bus>; |
| snps,reset-gpio = <&gpio0 RK_PC3 GPIO_ACTIVE_LOW>; |
| snps,reset-active-low; |
| /* Reset time is 20ms, 100ms for rtl8211f */ |
| snps,reset-delays-us = <0 20000 100000>; |
| tx_delay = <0x30>; |
| rx_delay = <0x10>; |
| phy-handle = <&rgmii_phy1>; |
| status = "okay"; |
| }; |
| |
| &gpu { |
| mali-supply = <&vdd_gpu>; |
| status = "okay"; |
| }; |
| |
| &hdmi { |
| avdd-0v9-supply = <&vdda_0v9>; |
| avdd-1v8-supply = <&vcc_1v8>; |
| status = "okay"; |
| }; |
| |
| &hdmi_in { |
| hdmi_in_vp0: endpoint { |
| remote-endpoint = <&vp0_out_hdmi>; |
| }; |
| }; |
| |
| &hdmi_out { |
| hdmi_out_con: endpoint { |
| remote-endpoint = <&hdmi_con_in>; |
| }; |
| }; |
| |
| &hdmi_sound { |
| status = "okay"; |
| }; |
| |
| &i2c0 { |
| status = "okay"; |
| |
| vdd_cpu: regulator@1c { |
| compatible = "tcs,tcs4525"; |
| reg = <0x1c>; |
| fcs,suspend-voltage-selector = <1>; |
| regulator-name = "vdd_cpu"; |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <1150000>; |
| regulator-ramp-delay = <2300>; |
| regulator-always-on; |
| regulator-boot-on; |
| vin-supply = <&vcc_sys>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| rk817: pmic@20 { |
| compatible = "rockchip,rk817"; |
| reg = <0x20>; |
| interrupt-parent = <&gpio0>; |
| interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>; |
| assigned-clocks = <&cru I2S1_MCLKOUT_TX>; |
| assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>; |
| clock-names = "mclk"; |
| clocks = <&cru I2S1_MCLKOUT_TX>; |
| clock-output-names = "rk808-clkout1", "rk808-clkout2"; |
| #clock-cells = <1>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pmic_int_l>, <&i2s1m0_mclk>; |
| rockchip,system-power-controller; |
| #sound-dai-cells = <0>; |
| wakeup-source; |
| |
| vcc1-supply = <&vcc_sys>; |
| vcc2-supply = <&vcc_sys>; |
| vcc3-supply = <&vcc_sys>; |
| vcc4-supply = <&vcc_sys>; |
| vcc5-supply = <&vcc_sys>; |
| vcc6-supply = <&vcc_sys>; |
| vcc7-supply = <&vcc_sys>; |
| vcc8-supply = <&vcc_sys>; |
| vcc9-supply = <&dcdc_boost>; |
| |
| regulators { |
| vdd_logic: DCDC_REG1 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <500000>; |
| regulator-max-microvolt = <1350000>; |
| regulator-ramp-delay = <6001>; |
| regulator-initial-mode = <0x2>; |
| regulator-name = "vdd_logic"; |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| regulator-suspend-microvolt = <900000>; |
| }; |
| }; |
| |
| vdd_gpu: DCDC_REG2 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <500000>; |
| regulator-max-microvolt = <1350000>; |
| regulator-ramp-delay = <6001>; |
| regulator-initial-mode = <0x2>; |
| regulator-name = "vdd_gpu"; |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| vcc_ddr: DCDC_REG3 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-initial-mode = <0x2>; |
| regulator-name = "vcc_ddr"; |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| }; |
| }; |
| |
| vcc_3v3: DCDC_REG4 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-initial-mode = <0x2>; |
| regulator-name = "vcc_3v3"; |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| vcca1v8_pmu: LDO_REG1 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-name = "vcca1v8_pmu"; |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| regulator-suspend-microvolt = <1800000>; |
| }; |
| }; |
| |
| vdda_0v9: LDO_REG2 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <900000>; |
| regulator-max-microvolt = <900000>; |
| regulator-name = "vdda_0v9"; |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| vdda0v9_pmu: LDO_REG3 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <900000>; |
| regulator-max-microvolt = <900000>; |
| regulator-name = "vdda0v9_pmu"; |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| regulator-suspend-microvolt = <900000>; |
| }; |
| }; |
| |
| vccio_acodec: LDO_REG4 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-name = "vccio_acodec"; |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| vccio_sd: LDO_REG5 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-name = "vccio_sd"; |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| vcc3v3_pmu: LDO_REG6 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-name = "vcc3v3_pmu"; |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| regulator-suspend-microvolt = <3300000>; |
| }; |
| }; |
| |
| vcc_1v8: LDO_REG7 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-name = "vcc_1v8"; |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| vcc1v8_dvp: LDO_REG8 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-name = "vcc1v8_dvp"; |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| vcc2v8_dvp: LDO_REG9 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| regulator-name = "vcc2v8_dvp"; |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| dcdc_boost: BOOST { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| regulator-name = "boost"; |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| otg_switch: OTG_SWITCH { |
| regulator-name = "otg_switch"; |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| /* i2c3 is exposed on con40 |
| * pin 3 - i2c3_sda_m0, pullup to vcc_3v3 |
| * pin 5 - i2c3_scl_m0, pullup to vcc_3v3 |
| */ |
| &i2c3 { |
| status = "okay"; |
| }; |
| |
| &i2s0_8ch { |
| status = "okay"; |
| }; |
| |
| &i2s1_8ch { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2s1m0_sclktx |
| &i2s1m0_lrcktx |
| &i2s1m0_sdi0 |
| &i2s1m0_sdo0>; |
| rockchip,trcm-sync-tx-only; |
| status = "okay"; |
| }; |
| |
| &mdio1 { |
| rgmii_phy1: ethernet-phy@0 { |
| compatible = "ethernet-phy-ieee802.3-c22"; |
| reg = <0>; |
| }; |
| }; |
| |
| &pcie2x1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pcie_reset_h>; |
| reset-gpios = <&gpio1 RK_PB2 GPIO_ACTIVE_HIGH>; |
| vpcie3v3-supply = <&vcc3v3_pcie_p>; |
| status = "okay"; |
| }; |
| |
| &pinctrl { |
| bt { |
| bt_enable_h: bt-enable-h { |
| rockchip,pins = <2 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| |
| bt_host_wake_l: bt-host-wake-l { |
| rockchip,pins = <2 RK_PC0 RK_FUNC_GPIO &pcfg_pull_down>; |
| }; |
| |
| bt_wake_l: bt-wake-l { |
| rockchip,pins = <2 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| }; |
| |
| fan { |
| fan_en_h: fan-en-h { |
| rockchip,pins = <0 RK_PD5 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| }; |
| |
| leds { |
| work_led_enable_h: work-led-enable-h { |
| rockchip,pins = <0 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| |
| diy_led_enable_h: diy-led-enable-h { |
| rockchip,pins = <0 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| }; |
| |
| pcie { |
| pcie_enable_h: pcie-enable-h { |
| rockchip,pins = <0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| |
| pcie_reset_h: pcie-reset-h { |
| rockchip,pins = <1 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| }; |
| |
| pmic { |
| pmic_int_l: pmic-int-l { |
| rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>; |
| }; |
| }; |
| |
| usb2 { |
| vcc5v0_usb20_host_en: vcc5v0-usb20-host-en { |
| rockchip,pins = <4 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| }; |
| |
| sdio-pwrseq { |
| wifi_enable_h: wifi-enable-h { |
| rockchip,pins = <2 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| }; |
| |
| vcc_sd { |
| vcc_sd_h: vcc-sd-h { |
| rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| }; |
| }; |
| |
| &pmu_io_domains { |
| pmuio1-supply = <&vcc3v3_pmu>; |
| pmuio2-supply = <&vcc3v3_pmu>; |
| vccio1-supply = <&vccio_acodec>; |
| vccio2-supply = <&vcc_1v8>; |
| vccio3-supply = <&vccio_sd>; |
| vccio4-supply = <&vcc_1v8>; |
| vccio5-supply = <&vcc_3v3>; |
| vccio6-supply = <&vcc1v8_dvp>; |
| vccio7-supply = <&vcc_3v3>; |
| status = "okay"; |
| }; |
| |
| &sdhci { |
| bus-width = <8>; |
| mmc-hs200-1_8v; |
| non-removable; |
| vmmc-supply = <&vcc_3v3>; |
| vqmmc-supply = <&vcc_1v8>; |
| status = "okay"; |
| }; |
| |
| &sdmmc0 { |
| bus-width = <4>; |
| cap-sd-highspeed; |
| cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>; |
| disable-wp; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>; |
| sd-uhs-sdr104; |
| vmmc-supply = <&vcc3v3_sd>; |
| vqmmc-supply = <&vccio_sd>; |
| status = "okay"; |
| }; |
| |
| &sdmmc1 { |
| bus-width = <4>; |
| cap-sd-highspeed; |
| cap-sdio-irq; |
| keep-power-in-suspend; |
| mmc-pwrseq = <&sdio_pwrseq>; |
| non-removable; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&sdmmc1_bus4 &sdmmc1_cmd &sdmmc1_clk>; |
| sd-uhs-sdr104; |
| vmmc-supply = <&vcc_wl>; |
| vqmmc-supply = <&vcc_1v8>; |
| status = "okay"; |
| }; |
| |
| &sfc { |
| pinctrl-0 = <&fspi_pins>; |
| pinctrl-names = "default"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| |
| flash@0 { |
| compatible = "jedec,spi-nor"; |
| reg = <0>; |
| spi-max-frequency = <24000000>; |
| spi-rx-bus-width = <4>; |
| spi-tx-bus-width = <1>; |
| }; |
| }; |
| |
| /* spdif is exposed on con40 pin 18 */ |
| &spdif { |
| status = "okay"; |
| }; |
| |
| /* spi1 is exposed on con40 |
| * pin 11 - spi1_mosi_m1 |
| * pin 13 - spi1_miso_m1 |
| * pin 15 - spi1_clk_m1 |
| * pin 17 - spi1_cs0_m1 |
| */ |
| &spi1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&spi1m1_cs0 &spi1m1_pins>; |
| }; |
| |
| &tsadc { |
| /* tshut mode 0:CRU 1:GPIO */ |
| rockchip,hw-tshut-mode = <1>; |
| /* tshut polarity 0:LOW 1:HIGH */ |
| rockchip,hw-tshut-polarity = <0>; |
| status = "okay"; |
| }; |
| |
| /* uart0 is exposed on con40 |
| * pin 12 - uart0_tx |
| * pin 14 - uart0_rx |
| */ |
| &uart0 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart0_xfer>; |
| status = "okay"; |
| }; |
| |
| &uart1 { |
| dma-names = "tx", "rx"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart1m0_xfer &uart1m0_ctsn &uart1m0_rtsn>; |
| status = "okay"; |
| uart-has-rtscts; |
| |
| bluetooth { |
| compatible = "brcm,bcm43438-bt"; |
| clocks = <&rk817 1>; |
| clock-names = "lpo"; |
| host-wakeup-gpios = <&gpio2 RK_PC1 GPIO_ACTIVE_HIGH>; |
| device-wakeup-gpios = <&gpio2 RK_PC0 GPIO_ACTIVE_HIGH>; |
| shutdown-gpios = <&gpio2 RK_PB7 GPIO_ACTIVE_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&bt_host_wake_l &bt_wake_l &bt_enable_h>; |
| vbat-supply = <&vcc_sys>; |
| vddio-supply = <&vcca1v8_pmu>; |
| max-speed = <3000000>; |
| }; |
| }; |
| |
| /* uart2 is exposed on con40 |
| * pin 8 - uart2_tx_m0_debug |
| * pin 10 - uart2_rx_m0_debug |
| */ |
| &uart2 { |
| status = "okay"; |
| }; |
| |
| &usb_host0_ehci { |
| status = "okay"; |
| }; |
| |
| &usb_host0_ohci { |
| status = "okay"; |
| }; |
| |
| &usb_host1_ehci { |
| status = "okay"; |
| }; |
| |
| &usb_host1_ohci { |
| status = "okay"; |
| }; |
| |
| &usb_host0_xhci { |
| dr_mode = "host"; |
| status = "okay"; |
| }; |
| |
| /* usb3 controller is muxed with sata1 */ |
| &usb_host1_xhci { |
| status = "okay"; |
| }; |
| |
| &usb2phy0 { |
| status = "okay"; |
| }; |
| |
| &usb2phy0_host { |
| phy-supply = <&vcc5v0_usb20_host>; |
| status = "okay"; |
| }; |
| |
| &usb2phy0_otg { |
| phy-supply = <&vcc5v0_usb20_otg>; |
| status = "okay"; |
| }; |
| |
| &usb2phy1 { |
| status = "okay"; |
| }; |
| |
| &usb2phy1_host { |
| phy-supply = <&vcc5v0_usb20_host>; |
| status = "okay"; |
| }; |
| |
| &usb2phy1_otg { |
| phy-supply = <&vcc5v0_usb20_host>; |
| status = "okay"; |
| }; |
| |
| &vop { |
| assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>; |
| assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>; |
| status = "okay"; |
| }; |
| |
| &vop_mmu { |
| status = "okay"; |
| }; |
| |
| &vp0 { |
| vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 { |
| reg = <ROCKCHIP_VOP2_EP_HDMI0>; |
| remote-endpoint = <&hdmi_in_vp0>; |
| }; |
| }; |
