| // SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| /* |
| * Copyright (c) 2023 Theobroma Systems Design und Consulting GmbH |
| */ |
| |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/leds/common.h> |
| #include <dt-bindings/pinctrl/rockchip.h> |
| #include "rk3588.dtsi" |
| |
| / { |
| compatible = "tsd,rk3588-tiger", "rockchip,rk3588"; |
| |
| aliases { |
| mmc0 = &sdhci; |
| rtc0 = &rtc_twi; |
| }; |
| |
| emmc_pwrseq: emmc-pwrseq { |
| compatible = "mmc-pwrseq-emmc"; |
| pinctrl-0 = <&emmc_reset>; |
| pinctrl-names = "default"; |
| reset-gpios = <&gpio2 RK_PA3 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| extcon_usb3: extcon-usb3 { |
| compatible = "linux,extcon-usb-gpio"; |
| id-gpios = <&gpio3 RK_PC0 GPIO_ACTIVE_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&usb3_id>; |
| status = "disabled"; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&module_led_pin>; |
| |
| /* Named LED1 on the board */ |
| led-1 { |
| gpios = <&gpio1 RK_PD3 GPIO_ACTIVE_HIGH>; |
| function = LED_FUNCTION_HEARTBEAT; |
| linux,default-trigger = "heartbeat"; |
| color = <LED_COLOR_ID_AMBER>; |
| }; |
| }; |
| |
| /* |
| * 100MHz reference clock for PCIe peripherals from PI6C557-05BLE |
| * clock generator. |
| * The clock output is gated via the OE pin on the clock generator. |
| * This is modeled as a fixed-clock plus a gpio-gate-clock. |
| */ |
| pcie_refclk_gen: pcie-refclk-gen-clock { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <100000000>; |
| }; |
| |
| pcie_refclk: pcie-refclk-clock { |
| compatible = "gpio-gate-clock"; |
| clocks = <&pcie_refclk_gen>; |
| #clock-cells = <0>; |
| enable-gpios = <&gpio4 RK_PB4 GPIO_ACTIVE_HIGH>; /* PCIE30X4_CLKREQN_M1_L */ |
| }; |
| |
| vcc_1v1_nldo_s3: vcc-1v1-nldo-s3-regulator { |
| compatible = "regulator-fixed"; |
| regulator-name = "vcc_1v1_nldo_s3"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <1100000>; |
| regulator-max-microvolt = <1100000>; |
| vin-supply = <&vcc5v0_sys>; |
| }; |
| |
| vcc_1v2_s3: vcc-1v2-s3-regulator { |
| compatible = "regulator-fixed"; |
| regulator-name = "vcc_1v2_s3"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| vin-supply = <&vcc5v0_sys>; |
| }; |
| |
| vcc5v0_sys: vcc5v0-sys-regulator { |
| compatible = "regulator-fixed"; |
| regulator-name = "vcc5v0_sys"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| vin-supply = <&vcc5v0_baseboard>; |
| }; |
| }; |
| |
| &cpu_b0 { |
| cpu-supply = <&vdd_cpu_big0_s0>; |
| }; |
| |
| &cpu_b1 { |
| cpu-supply = <&vdd_cpu_big0_s0>; |
| }; |
| |
| &cpu_b2 { |
| cpu-supply = <&vdd_cpu_big1_s0>; |
| }; |
| |
| &cpu_b3 { |
| cpu-supply = <&vdd_cpu_big1_s0>; |
| }; |
| |
| &cpu_l0 { |
| cpu-supply = <&vdd_cpu_lit_s0>; |
| }; |
| |
| &cpu_l1 { |
| cpu-supply = <&vdd_cpu_lit_s0>; |
| }; |
| |
| &cpu_l2 { |
| cpu-supply = <&vdd_cpu_lit_s0>; |
| }; |
| |
| &cpu_l3 { |
| cpu-supply = <&vdd_cpu_lit_s0>; |
| }; |
| |
| &gmac0 { |
| clock_in_out = "output"; |
| phy-handle = <&rgmii_phy>; |
| phy-mode = "rgmii"; |
| phy-supply = <&vcc_1v2_s3>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&gmac0_miim |
| &gmac0_rx_bus2 |
| &gmac0_tx_bus2 |
| &gmac0_rgmii_clk |
| &gmac0_rgmii_bus |
| ð0_pins |
| ð_reset>; |
| tx_delay = <0x10>; |
| rx_delay = <0x10>; |
| snps,reset-gpio = <&gpio4 RK_PC3 GPIO_ACTIVE_LOW>; |
| snps,reset-active-low; |
| snps,reset-delays-us = <0 10000 100000>; |
| }; |
| |
| &gpu { |
| mali-supply = <&vdd_gpu_s0>; |
| status = "okay"; |
| }; |
| |
| &i2c1 { |
| pinctrl-0 = <&i2c1m0_xfer>; |
| }; |
| |
| &i2c1m0_xfer { |
| rockchip,pins = |
| /* i2c1_scl_m0 */ |
| <0 RK_PB5 9 &pcfg_pull_none_drv_level_0>, |
| /* i2c1_sda_m0 */ |
| <0 RK_PB6 9 &pcfg_pull_none_drv_level_0>; |
| }; |
| |
| &i2c2 { |
| pinctrl-0 = <&i2c2m3_xfer>; |
| status = "okay"; |
| }; |
| |
| &i2c2m3_xfer { |
| rockchip,pins = |
| /* i2c2_scl_m3 */ |
| <1 RK_PC5 9 &pcfg_pull_none_drv_level_0>, |
| /* i2c2_sda_m3 */ |
| <1 RK_PC4 9 &pcfg_pull_none_drv_level_0>; |
| }; |
| |
| &i2c3 { |
| pinctrl-0 = <&i2c3m0_xfer>; |
| }; |
| |
| &i2c4 { |
| pinctrl-0 = <&i2c4m4_xfer>; |
| status = "okay"; |
| |
| vdd_npu_s0: regulator@42 { |
| compatible = "rockchip,rk8602"; |
| reg = <0x42>; |
| fcs,suspend-voltage-selector = <1>; |
| regulator-name = "vdd_npu_s0"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <550000>; |
| regulator-max-microvolt = <950000>; |
| regulator-ramp-delay = <2300>; |
| vin-supply = <&vcc5v0_sys>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| }; |
| |
| &i2c5 { |
| pinctrl-0 = <&i2c5m1_xfer>; |
| }; |
| |
| &i2c5m1_xfer { |
| rockchip,pins = |
| /* i2c5_scl_m1 */ |
| <4 RK_PB6 9 &pcfg_pull_none_drv_level_0>, |
| /* i2c5_sda_m1 */ |
| <4 RK_PB7 9 &pcfg_pull_none_drv_level_0>; |
| }; |
| |
| &i2c6 { |
| /* |
| * Mule-ATtiny can handle up to Fast mode Plus (1MHz) on I2C bus, |
| * but SOC can handle only up to (400kHz). |
| */ |
| clock-frequency = <400000>; |
| status = "okay"; |
| |
| fan@18 { |
| compatible = "ti,amc6821"; |
| reg = <0x18>; |
| }; |
| |
| rtc_twi: rtc@6f { |
| compatible = "isil,isl1208"; |
| reg = <0x6f>; |
| }; |
| }; |
| |
| &i2c6m0_xfer { |
| rockchip,pins = |
| /* i2c6_scl_m0 */ |
| <0 RK_PD0 9 &pcfg_pull_none_drv_level_0>, |
| /* i2c6_sda_m0 */ |
| <0 RK_PC7 9 &pcfg_pull_none_drv_level_0>; |
| }; |
| |
| &i2c7 { |
| status = "okay"; |
| |
| vdd_cpu_big0_s0: regulator@42 { |
| compatible = "rockchip,rk8602"; |
| reg = <0x42>; |
| fcs,suspend-voltage-selector = <1>; |
| regulator-name = "vdd_cpu_big0_s0"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <550000>; |
| regulator-max-microvolt = <1050000>; |
| regulator-ramp-delay = <2300>; |
| vin-supply = <&vcc5v0_sys>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| vdd_cpu_big1_s0: regulator@43 { |
| compatible = "rockchip,rk8603", "rockchip,rk8602"; |
| reg = <0x43>; |
| fcs,suspend-voltage-selector = <1>; |
| regulator-name = "vdd_cpu_big1_s0"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <550000>; |
| regulator-max-microvolt = <1050000>; |
| regulator-ramp-delay = <2300>; |
| vin-supply = <&vcc5v0_sys>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| }; |
| |
| &i2c7m0_xfer { |
| rockchip,pins = |
| /* i2c7_scl_m0 */ |
| <1 RK_PD0 9 &pcfg_pull_none_drv_level_0>, |
| /* i2c7_sda_m0 */ |
| <1 RK_PD1 9 &pcfg_pull_none_drv_level_0>; |
| }; |
| |
| &i2c8 { |
| pinctrl-0 = <&i2c8m2_xfer>; |
| }; |
| |
| &mdio0 { |
| rgmii_phy: ethernet-phy@6 { |
| /* KSZ9031 or KSZ9131 */ |
| compatible = "ethernet-phy-ieee802.3-c22"; |
| reg = <0x6>; |
| clocks = <&cru REFCLKO25M_ETH0_OUT>; |
| }; |
| }; |
| |
| &pcie3x4 { |
| /* |
| * The board has a gpio-controlled "pcie_refclk" generator, |
| * so add it to the list of clocks. |
| */ |
| clocks = <&cru ACLK_PCIE_4L_MSTR>, <&cru ACLK_PCIE_4L_SLV>, |
| <&cru ACLK_PCIE_4L_DBI>, <&cru PCLK_PCIE_4L>, |
| <&cru CLK_PCIE_AUX0>, <&cru CLK_PCIE4L_PIPE>, |
| <&pcie_refclk>; |
| clock-names = "aclk_mst", "aclk_slv", |
| "aclk_dbi", "pclk", |
| "aux", "pipe", |
| "ref"; |
| reset-gpios = <&gpio3 RK_PB6 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| &pinctrl { |
| emmc { |
| emmc_reset: emmc-reset { |
| rockchip,pins = <2 RK_PA3 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| }; |
| |
| ethernet { |
| eth_reset: eth-reset { |
| rockchip,pins = <4 RK_PC3 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| }; |
| |
| leds { |
| module_led_pin: module-led-pin { |
| rockchip,pins = <1 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| }; |
| |
| usb3 { |
| usb3_id: usb3-id { |
| rockchip,pins = |
| <3 RK_PC0 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| }; |
| }; |
| |
| &pwm0 { |
| pinctrl-0 = <&pwm0m1_pins>; |
| pinctrl-names = "default"; |
| }; |
| |
| &saradc { |
| vref-supply = <&vcc_1v8_s0>; |
| status = "okay"; |
| }; |
| |
| &sdhci { |
| bus-width = <8>; |
| cap-mmc-highspeed; |
| mmc-ddr-1_8v; |
| mmc-hs200-1_8v; |
| mmc-hs400-1_8v; |
| mmc-hs400-enhanced-strobe; |
| mmc-pwrseq = <&emmc_pwrseq>; |
| no-sdio; |
| no-sd; |
| non-removable; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&emmc_bus8 &emmc_cmd &emmc_clk &emmc_data_strobe>; |
| supports-cqe; |
| vmmc-supply = <&vcc_3v3_s3>; |
| vqmmc-supply = <&vcc_1v8_s3>; |
| status = "okay"; |
| }; |
| |
| &sdmmc { |
| bus-width = <4>; |
| cap-sd-highspeed; |
| max-frequency = <150000000>; |
| vqmmc-supply = <&vccio_sd_s0>; |
| }; |
| |
| &spi0 { |
| pinctrl-0 = <&spi0m1_cs0 &spi0m1_cs1 &spi0m3_pins>; |
| }; |
| |
| &spi2 { |
| assigned-clocks = <&cru CLK_SPI2>; |
| assigned-clock-rates = <200000000>; |
| num-cs = <1>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&spi2m2_cs0 &spi2m2_pins>; |
| status = "okay"; |
| |
| pmic@0 { |
| compatible = "rockchip,rk806"; |
| reg = <0x0>; |
| interrupt-parent = <&gpio0>; |
| interrupts = <7 IRQ_TYPE_LEVEL_LOW>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pmic_pins>, <&rk806_dvs1_null>, |
| <&rk806_dvs2_null>, <&rk806_dvs3_null>; |
| spi-max-frequency = <1000000>; |
| system-power-controller; |
| vcc1-supply = <&vcc5v0_sys>; |
| vcc2-supply = <&vcc5v0_sys>; |
| vcc3-supply = <&vcc5v0_sys>; |
| vcc4-supply = <&vcc5v0_sys>; |
| vcc5-supply = <&vcc5v0_sys>; |
| vcc6-supply = <&vcc5v0_sys>; |
| vcc7-supply = <&vcc5v0_sys>; |
| vcc8-supply = <&vcc5v0_sys>; |
| vcc9-supply = <&vcc5v0_sys>; |
| vcc10-supply = <&vcc5v0_sys>; |
| vcc11-supply = <&vcc_2v0_pldo_s3>; |
| vcc12-supply = <&vcc5v0_sys>; |
| vcc13-supply = <&vcc_1v1_nldo_s3>; |
| vcc14-supply = <&vcc_1v1_nldo_s3>; |
| vcca-supply = <&vcc5v0_sys>; |
| |
| rk806_dvs1_null: dvs1-null-pins { |
| pins = "gpio_pwrctrl1"; |
| function = "pin_fun0"; |
| }; |
| |
| rk806_dvs2_null: dvs2-null-pins { |
| pins = "gpio_pwrctrl2"; |
| function = "pin_fun0"; |
| }; |
| |
| rk806_dvs3_null: dvs3-null-pins { |
| pins = "gpio_pwrctrl3"; |
| function = "pin_fun0"; |
| }; |
| |
| regulators { |
| vdd_gpu_s0: dcdc-reg1 { |
| regulator-boot-on; |
| regulator-min-microvolt = <550000>; |
| regulator-max-microvolt = <950000>; |
| regulator-ramp-delay = <12500>; |
| regulator-name = "vdd_gpu_s0"; |
| regulator-enable-ramp-delay = <400>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| vdd_cpu_lit_s0: dcdc-reg2 { |
| regulator-name = "vdd_cpu_lit_s0"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <550000>; |
| regulator-max-microvolt = <950000>; |
| regulator-ramp-delay = <12500>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| vdd_log_s0: dcdc-reg3 { |
| regulator-name = "vdd_log_s0"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <675000>; |
| regulator-max-microvolt = <750000>; |
| regulator-ramp-delay = <12500>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| regulator-suspend-microvolt = <750000>; |
| }; |
| }; |
| |
| vdd_vdenc_s0: dcdc-reg4 { |
| regulator-name = "vdd_vdenc_s0"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <550000>; |
| regulator-max-microvolt = <950000>; |
| regulator-ramp-delay = <12500>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| vdd_ddr_s0: dcdc-reg5 { |
| regulator-name = "vdd_ddr_s0"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <675000>; |
| regulator-max-microvolt = <900000>; |
| regulator-ramp-delay = <12500>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| regulator-suspend-microvolt = <850000>; |
| }; |
| }; |
| |
| vdd2_ddr_s3: dcdc-reg6 { |
| regulator-name = "vdd2_ddr_s3"; |
| regulator-always-on; |
| regulator-boot-on; |
| |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| }; |
| }; |
| |
| vcc_2v0_pldo_s3: dcdc-reg7 { |
| regulator-name = "vcc_2v0_pldo_s3"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <2000000>; |
| regulator-max-microvolt = <2000000>; |
| regulator-ramp-delay = <12500>; |
| |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| regulator-suspend-microvolt = <2000000>; |
| }; |
| }; |
| |
| vcc_3v3_s3: dcdc-reg8 { |
| regulator-name = "vcc_3v3_s3"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| regulator-suspend-microvolt = <3300000>; |
| }; |
| }; |
| |
| vddq_ddr_s0: dcdc-reg9 { |
| regulator-name = "vddq_ddr_s0"; |
| regulator-always-on; |
| regulator-boot-on; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| vcc_1v8_s3: dcdc-reg10 { |
| regulator-name = "vcc_1v8_s3"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| regulator-suspend-microvolt = <1800000>; |
| }; |
| }; |
| |
| vcca_1v8_s0: pldo-reg1 { |
| regulator-name = "vcca_1v8_s0"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| vcc_1v8_s0: pldo-reg2 { |
| regulator-name = "vcc_1v8_s0"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| regulator-suspend-microvolt = <1800000>; |
| }; |
| }; |
| |
| vdda_1v2_s0: pldo-reg3 { |
| regulator-name = "vdda_1v2_s0"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| vcca_3v3_s0: pldo-reg4 { |
| regulator-name = "vcca_3v3_s0"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-ramp-delay = <12500>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| vccio_sd_s0: pldo-reg5 { |
| regulator-name = "vccio_sd_s0"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-ramp-delay = <12500>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| pldo6_s3: pldo-reg6 { |
| regulator-name = "pldo6_s3"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| regulator-suspend-microvolt = <1800000>; |
| }; |
| }; |
| |
| vdd_0v75_s3: nldo-reg1 { |
| regulator-name = "vdd_0v75_s3"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <750000>; |
| regulator-max-microvolt = <750000>; |
| |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| regulator-suspend-microvolt = <750000>; |
| }; |
| }; |
| |
| vdda_ddr_pll_s0: nldo-reg2 { |
| regulator-name = "vdda_ddr_pll_s0"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <850000>; |
| regulator-max-microvolt = <850000>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| regulator-suspend-microvolt = <850000>; |
| }; |
| }; |
| |
| vdda_0v75_s0: nldo-reg3 { |
| regulator-name = "vdda_0v75_s0"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <750000>; |
| regulator-max-microvolt = <750000>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| vdda_0v85_s0: nldo-reg4 { |
| regulator-name = "vdda_0v85_s0"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <850000>; |
| regulator-max-microvolt = <850000>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| vdd_0v75_s0: nldo-reg5 { |
| regulator-name = "vdd_0v75_s0"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <750000>; |
| regulator-max-microvolt = <750000>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| &tsadc { |
| status = "okay"; |
| }; |
| |
| /* Routed to UART0 on the Q7 connector */ |
| &uart2 { |
| pinctrl-0 = <&uart2m2_xfer>; |
| }; |
| |
| /* Mule-ATtiny UPDI */ |
| &uart4 { |
| pinctrl-0 = <&uart4m2_xfer>; |
| status = "okay"; |
| }; |
