| // SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| /* |
| * Copyright 2019 NXP |
| * Copyright (C) 2020 Krzysztof Kozlowski <krzk@kernel.org> |
| */ |
| |
| #include "imx8mm.dtsi" |
| |
| / { |
| model = "Variscite VAR-SOM-MX8MM module"; |
| compatible = "variscite,var-som-mx8mm", "fsl,imx8mm"; |
| |
| chosen { |
| stdout-path = &uart4; |
| }; |
| |
| memory@40000000 { |
| device_type = "memory"; |
| reg = <0x0 0x40000000 0 0x80000000>; |
| }; |
| |
| reg_eth_phy: regulator-eth-phy { |
| compatible = "regulator-fixed"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_reg_eth_phy>; |
| regulator-name = "eth_phy_pwr"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| gpio = <&gpio2 9 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| }; |
| }; |
| |
| &A53_0 { |
| cpu-supply = <&buck2_reg>; |
| }; |
| |
| &A53_1 { |
| cpu-supply = <&buck2_reg>; |
| }; |
| |
| &A53_2 { |
| cpu-supply = <&buck2_reg>; |
| }; |
| |
| &A53_3 { |
| cpu-supply = <&buck2_reg>; |
| }; |
| |
| &ddrc { |
| operating-points-v2 = <&ddrc_opp_table>; |
| |
| ddrc_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| |
| opp-25M { |
| opp-hz = /bits/ 64 <25000000>; |
| }; |
| |
| opp-100M { |
| opp-hz = /bits/ 64 <100000000>; |
| }; |
| |
| opp-750M { |
| opp-hz = /bits/ 64 <750000000>; |
| }; |
| }; |
| }; |
| |
| &ecspi1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_ecspi1>; |
| cs-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>, |
| <&gpio1 0 GPIO_ACTIVE_LOW>; |
| /delete-property/ dmas; |
| /delete-property/ dma-names; |
| status = "okay"; |
| |
| /* Resistive touch controller */ |
| touchscreen@0 { |
| reg = <0>; |
| compatible = "ti,ads7846"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_restouch>; |
| interrupt-parent = <&gpio1>; |
| interrupts = <3 IRQ_TYPE_EDGE_FALLING>; |
| |
| spi-max-frequency = <1500000>; |
| pendown-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>; |
| |
| ti,x-min = /bits/ 16 <125>; |
| touchscreen-size-x = /bits/ 16 <4008>; |
| ti,y-min = /bits/ 16 <282>; |
| touchscreen-size-y = /bits/ 16 <3864>; |
| ti,x-plate-ohms = /bits/ 16 <180>; |
| touchscreen-max-pressure = /bits/ 16 <255>; |
| touchscreen-average-samples = /bits/ 16 <10>; |
| ti,debounce-tol = /bits/ 16 <3>; |
| ti,debounce-rep = /bits/ 16 <1>; |
| ti,settle-delay-usec = /bits/ 16 <150>; |
| ti,keep-vref-on; |
| wakeup-source; |
| }; |
| }; |
| |
| &fec1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_fec1>; |
| phy-mode = "rgmii"; |
| phy-handle = <ðphy>; |
| phy-supply = <®_eth_phy>; |
| fsl,magic-packet; |
| status = "okay"; |
| |
| mdio { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| ethphy: ethernet-phy@4 { |
| compatible = "ethernet-phy-ieee802.3-c22"; |
| reg = <4>; |
| reset-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; |
| reset-assert-us = <10000>; |
| reset-deassert-us = <10000>; |
| }; |
| }; |
| }; |
| |
| &i2c1 { |
| clock-frequency = <400000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c1>; |
| status = "okay"; |
| |
| pmic@4b { |
| compatible = "rohm,bd71847"; |
| reg = <0x4b>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pmic>; |
| interrupt-parent = <&gpio2>; |
| interrupts = <8 IRQ_TYPE_LEVEL_LOW>; |
| rohm,reset-snvs-powered; |
| |
| #clock-cells = <0>; |
| clocks = <&osc_32k 0>; |
| clock-output-names = "clk-32k-out"; |
| |
| regulators { |
| buck1_reg: BUCK1 { |
| regulator-name = "buck1"; |
| regulator-min-microvolt = <700000>; |
| regulator-max-microvolt = <1300000>; |
| regulator-boot-on; |
| regulator-always-on; |
| regulator-ramp-delay = <1250>; |
| }; |
| |
| buck2_reg: BUCK2 { |
| regulator-name = "buck2"; |
| regulator-min-microvolt = <700000>; |
| regulator-max-microvolt = <1300000>; |
| regulator-boot-on; |
| regulator-always-on; |
| regulator-ramp-delay = <1250>; |
| rohm,dvs-run-voltage = <1000000>; |
| rohm,dvs-idle-voltage = <900000>; |
| }; |
| |
| buck3_reg: BUCK3 { |
| regulator-name = "buck3"; |
| regulator-min-microvolt = <700000>; |
| regulator-max-microvolt = <1350000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| buck4_reg: BUCK4 { |
| regulator-name = "buck4"; |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| buck5_reg: BUCK5 { |
| regulator-name = "buck5"; |
| regulator-min-microvolt = <1605000>; |
| regulator-max-microvolt = <1995000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| buck6_reg: BUCK6 { |
| regulator-name = "buck6"; |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <1400000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| ldo1_reg: LDO1 { |
| regulator-name = "ldo1"; |
| regulator-min-microvolt = <1600000>; |
| regulator-max-microvolt = <1900000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| ldo2_reg: LDO2 { |
| regulator-name = "ldo2"; |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <900000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| ldo3_reg: LDO3 { |
| regulator-name = "ldo3"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| ldo4_reg: LDO4 { |
| regulator-name = "ldo4"; |
| regulator-min-microvolt = <900000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| ldo5_reg: LDO5 { |
| regulator-compatible = "ldo5"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-always-on; |
| }; |
| |
| ldo6_reg: LDO6 { |
| regulator-name = "ldo6"; |
| regulator-min-microvolt = <900000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| }; |
| }; |
| }; |
| |
| &i2c3 { |
| clock-frequency = <400000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c3>; |
| status = "okay"; |
| |
| /* TODO: configure audio, as of now just put a placeholder */ |
| wm8904: codec@1a { |
| compatible = "wlf,wm8904"; |
| reg = <0x1a>; |
| status = "disabled"; |
| }; |
| }; |
| |
| &snvs_pwrkey { |
| status = "okay"; |
| }; |
| |
| /* Bluetooth */ |
| &uart2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart2>; |
| assigned-clocks = <&clk IMX8MM_CLK_UART2>; |
| assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>; |
| uart-has-rtscts; |
| status = "okay"; |
| }; |
| |
| /* Console */ |
| &uart4 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart4>; |
| status = "okay"; |
| }; |
| |
| &usbotg1 { |
| dr_mode = "otg"; |
| usb-role-switch; |
| status = "okay"; |
| }; |
| |
| &usbotg2 { |
| dr_mode = "otg"; |
| usb-role-switch; |
| status = "okay"; |
| }; |
| |
| /* WIFI */ |
| &usdhc1 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| pinctrl-names = "default", "state_100mhz", "state_200mhz"; |
| pinctrl-0 = <&pinctrl_usdhc1>; |
| pinctrl-1 = <&pinctrl_usdhc1_100mhz>; |
| pinctrl-2 = <&pinctrl_usdhc1_200mhz>; |
| bus-width = <4>; |
| non-removable; |
| keep-power-in-suspend; |
| status = "okay"; |
| |
| brcmf: bcrmf@1 { |
| reg = <1>; |
| compatible = "brcm,bcm4329-fmac"; |
| }; |
| }; |
| |
| /* SD */ |
| &usdhc2 { |
| assigned-clocks = <&clk IMX8MM_CLK_USDHC2>; |
| assigned-clock-rates = <200000000>; |
| pinctrl-names = "default", "state_100mhz", "state_200mhz"; |
| pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; |
| pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>; |
| pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>; |
| cd-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>; |
| bus-width = <4>; |
| vmmc-supply = <®_usdhc2_vmmc>; |
| status = "okay"; |
| }; |
| |
| /* eMMC */ |
| &usdhc3 { |
| assigned-clocks = <&clk IMX8MM_CLK_USDHC3_ROOT>; |
| assigned-clock-rates = <400000000>; |
| pinctrl-names = "default", "state_100mhz", "state_200mhz"; |
| pinctrl-0 = <&pinctrl_usdhc3>; |
| pinctrl-1 = <&pinctrl_usdhc3_100mhz>; |
| pinctrl-2 = <&pinctrl_usdhc3_200mhz>; |
| bus-width = <8>; |
| non-removable; |
| status = "okay"; |
| }; |
| |
| &wdog1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_wdog>; |
| fsl,ext-reset-output; |
| status = "okay"; |
| }; |
| |
| &iomuxc { |
| pinctrl_ecspi1: ecspi1grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK 0x13 |
| MX8MM_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI 0x13 |
| MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO 0x13 |
| MX8MM_IOMUXC_GPIO1_IO14_GPIO1_IO14 0x13 |
| MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x13 |
| >; |
| }; |
| |
| pinctrl_fec1: fec1grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x3 |
| MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3 |
| MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f |
| MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f |
| MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f |
| MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f |
| MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91 |
| MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91 |
| MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91 |
| MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91 |
| MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f |
| MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91 |
| MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91 |
| MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f |
| MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x19 |
| >; |
| }; |
| |
| pinctrl_i2c1: i2c1grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c3 |
| MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c3 |
| >; |
| }; |
| |
| pinctrl_i2c3: i2c3grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x400001c3 |
| MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001c3 |
| >; |
| }; |
| |
| pinctrl_pmic: pmicirqgrp { |
| fsl,pins = < |
| MX8MM_IOMUXC_SD1_DATA6_GPIO2_IO8 0x141 |
| >; |
| }; |
| |
| pinctrl_reg_eth_phy: regethphygrp { |
| fsl,pins = < |
| MX8MM_IOMUXC_SD1_DATA7_GPIO2_IO9 0x41 |
| >; |
| }; |
| |
| pinctrl_restouch: restouchgrp { |
| fsl,pins = < |
| MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x1c0 |
| >; |
| }; |
| |
| pinctrl_uart2: uart2grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX 0x140 |
| MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX 0x140 |
| MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B 0x140 |
| MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B 0x140 |
| >; |
| }; |
| |
| pinctrl_uart4: uart4grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_UART4_RXD_UART4_DCE_RX 0x140 |
| MX8MM_IOMUXC_UART4_TXD_UART4_DCE_TX 0x140 |
| >; |
| }; |
| |
| pinctrl_usdhc1: usdhc1grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x190 |
| MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d0 |
| MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d0 |
| MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d0 |
| MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d0 |
| MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d0 |
| >; |
| }; |
| |
| pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp { |
| fsl,pins = < |
| MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x194 |
| MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d4 |
| MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d4 |
| MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d4 |
| MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d4 |
| MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d4 |
| >; |
| }; |
| |
| pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp { |
| fsl,pins = < |
| MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x196 |
| MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d6 |
| MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d6 |
| MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d6 |
| MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d6 |
| MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d6 |
| >; |
| }; |
| |
| pinctrl_usdhc2_gpio: usdhc2gpiogrp { |
| fsl,pins = < |
| MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10 0xc1 |
| >; |
| }; |
| |
| pinctrl_usdhc2: usdhc2grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x190 |
| MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0 |
| MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0 |
| MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0 |
| MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0 |
| MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0 |
| MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 |
| >; |
| }; |
| |
| pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp { |
| fsl,pins = < |
| MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x194 |
| MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4 |
| MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4 |
| MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4 |
| MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4 |
| MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4 |
| MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 |
| >; |
| }; |
| |
| pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp { |
| fsl,pins = < |
| MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x196 |
| MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6 |
| MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6 |
| MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6 |
| MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6 |
| MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6 |
| MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 |
| >; |
| }; |
| |
| pinctrl_usdhc3: usdhc3grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x190 |
| MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d0 |
| MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d0 |
| MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d0 |
| MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d0 |
| MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d0 |
| MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d0 |
| MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d0 |
| MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d0 |
| MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d0 |
| MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x190 |
| >; |
| }; |
| |
| pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp { |
| fsl,pins = < |
| MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x194 |
| MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d4 |
| MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4 |
| MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4 |
| MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4 |
| MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4 |
| MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4 |
| MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4 |
| MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4 |
| MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4 |
| MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x194 |
| >; |
| }; |
| |
| pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp { |
| fsl,pins = < |
| MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x196 |
| MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d6 |
| MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d6 |
| MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d6 |
| MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d6 |
| MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d6 |
| MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d6 |
| MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d6 |
| MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d6 |
| MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d6 |
| MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x196 |
| >; |
| }; |
| |
| pinctrl_wdog: wdoggrp { |
| fsl,pins = < |
| MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0x166 |
| >; |
| }; |
| }; |
