| /* |
| * This only handles 32bit MTRR on 32bit hosts. This is strictly wrong |
| * because MTRRs can span up to 40 bits (36bits on most modern x86) |
| */ |
| #define DEBUG |
| |
| #include <linux/module.h> |
| #include <linux/init.h> |
| #include <linux/io.h> |
| #include <linux/mm.h> |
| |
| #include <asm/processor-flags.h> |
| #include <asm/cpufeature.h> |
| #include <asm/tlbflush.h> |
| #include <asm/mtrr.h> |
| #include <asm/msr.h> |
| #include <asm/pat.h> |
| |
| #include "mtrr.h" |
| |
| struct fixed_range_block { |
| int base_msr; /* start address of an MTRR block */ |
| int ranges; /* number of MTRRs in this block */ |
| }; |
| |
| static struct fixed_range_block fixed_range_blocks[] = { |
| { MSR_MTRRfix64K_00000, 1 }, /* one 64k MTRR */ |
| { MSR_MTRRfix16K_80000, 2 }, /* two 16k MTRRs */ |
| { MSR_MTRRfix4K_C0000, 8 }, /* eight 4k MTRRs */ |
| {} |
| }; |
| |
| static unsigned long smp_changes_mask; |
| static int mtrr_state_set; |
| u64 mtrr_tom2; |
| |
| struct mtrr_state_type mtrr_state; |
| EXPORT_SYMBOL_GPL(mtrr_state); |
| |
| /* |
| * BIOS is expected to clear MtrrFixDramModEn bit, see for example |
| * "BIOS and Kernel Developer's Guide for the AMD Athlon 64 and AMD |
| * Opteron Processors" (26094 Rev. 3.30 February 2006), section |
| * "13.2.1.2 SYSCFG Register": "The MtrrFixDramModEn bit should be set |
| * to 1 during BIOS initalization of the fixed MTRRs, then cleared to |
| * 0 for operation." |
| */ |
| static inline void k8_check_syscfg_dram_mod_en(void) |
| { |
| u32 lo, hi; |
| |
| if (!((boot_cpu_data.x86_vendor == X86_VENDOR_AMD) && |
| (boot_cpu_data.x86 >= 0x0f))) |
| return; |
| |
| rdmsr(MSR_K8_SYSCFG, lo, hi); |
| if (lo & K8_MTRRFIXRANGE_DRAM_MODIFY) { |
| printk(KERN_ERR FW_WARN "MTRR: CPU %u: SYSCFG[MtrrFixDramModEn]" |
| " not cleared by BIOS, clearing this bit\n", |
| smp_processor_id()); |
| lo &= ~K8_MTRRFIXRANGE_DRAM_MODIFY; |
| mtrr_wrmsr(MSR_K8_SYSCFG, lo, hi); |
| } |
| } |
| |
| /* Get the size of contiguous MTRR range */ |
| static u64 get_mtrr_size(u64 mask) |
| { |
| u64 size; |
| |
| mask >>= PAGE_SHIFT; |
| mask |= size_or_mask; |
| size = -mask; |
| size <<= PAGE_SHIFT; |
| return size; |
| } |
| |
| /* |
| * Check and return the effective type for MTRR-MTRR type overlap. |
| * Returns 1 if the effective type is UNCACHEABLE, else returns 0 |
| */ |
| static int check_type_overlap(u8 *prev, u8 *curr) |
| { |
| if (*prev == MTRR_TYPE_UNCACHABLE || *curr == MTRR_TYPE_UNCACHABLE) { |
| *prev = MTRR_TYPE_UNCACHABLE; |
| *curr = MTRR_TYPE_UNCACHABLE; |
| return 1; |
| } |
| |
| if ((*prev == MTRR_TYPE_WRBACK && *curr == MTRR_TYPE_WRTHROUGH) || |
| (*prev == MTRR_TYPE_WRTHROUGH && *curr == MTRR_TYPE_WRBACK)) { |
| *prev = MTRR_TYPE_WRTHROUGH; |
| *curr = MTRR_TYPE_WRTHROUGH; |
| } |
| |
| if (*prev != *curr) { |
| *prev = MTRR_TYPE_UNCACHABLE; |
| *curr = MTRR_TYPE_UNCACHABLE; |
| return 1; |
| } |
| |
| return 0; |
| } |
| |
| /** |
| * mtrr_type_lookup_fixed - look up memory type in MTRR fixed entries |
| * |
| * Return the MTRR fixed memory type of 'start'. |
| * |
| * MTRR fixed entries are divided into the following ways: |
| * 0x00000 - 0x7FFFF : This range is divided into eight 64KB sub-ranges |
| * 0x80000 - 0xBFFFF : This range is divided into sixteen 16KB sub-ranges |
| * 0xC0000 - 0xFFFFF : This range is divided into sixty-four 4KB sub-ranges |
| * |
| * Return Values: |
| * MTRR_TYPE_(type) - Matched memory type |
| * MTRR_TYPE_INVALID - Unmatched |
| */ |
| static u8 mtrr_type_lookup_fixed(u64 start, u64 end) |
| { |
| int idx; |
| |
| if (start >= 0x100000) |
| return MTRR_TYPE_INVALID; |
| |
| /* 0x0 - 0x7FFFF */ |
| if (start < 0x80000) { |
| idx = 0; |
| idx += (start >> 16); |
| return mtrr_state.fixed_ranges[idx]; |
| /* 0x80000 - 0xBFFFF */ |
| } else if (start < 0xC0000) { |
| idx = 1 * 8; |
| idx += ((start - 0x80000) >> 14); |
| return mtrr_state.fixed_ranges[idx]; |
| } |
| |
| /* 0xC0000 - 0xFFFFF */ |
| idx = 3 * 8; |
| idx += ((start - 0xC0000) >> 12); |
| return mtrr_state.fixed_ranges[idx]; |
| } |
| |
| /** |
| * mtrr_type_lookup_variable - look up memory type in MTRR variable entries |
| * |
| * Return Value: |
| * MTRR_TYPE_(type) - Matched memory type or default memory type (unmatched) |
| * |
| * Output Arguments: |
| * repeat - Set to 1 when [start:end] spanned across MTRR range and type |
| * returned corresponds only to [start:*partial_end]. Caller has |
| * to lookup again for [*partial_end:end]. |
| * |
| * uniform - Set to 1 when an MTRR covers the region uniformly, i.e. the |
| * region is fully covered by a single MTRR entry or the default |
| * type. |
| */ |
| static u8 mtrr_type_lookup_variable(u64 start, u64 end, u64 *partial_end, |
| int *repeat, u8 *uniform) |
| { |
| int i; |
| u64 base, mask; |
| u8 prev_match, curr_match; |
| |
| *repeat = 0; |
| *uniform = 1; |
| |
| /* Make end inclusive instead of exclusive */ |
| end--; |
| |
| prev_match = MTRR_TYPE_INVALID; |
| for (i = 0; i < num_var_ranges; ++i) { |
| unsigned short start_state, end_state, inclusive; |
| |
| if (!(mtrr_state.var_ranges[i].mask_lo & (1 << 11))) |
| continue; |
| |
| base = (((u64)mtrr_state.var_ranges[i].base_hi) << 32) + |
| (mtrr_state.var_ranges[i].base_lo & PAGE_MASK); |
| mask = (((u64)mtrr_state.var_ranges[i].mask_hi) << 32) + |
| (mtrr_state.var_ranges[i].mask_lo & PAGE_MASK); |
| |
| start_state = ((start & mask) == (base & mask)); |
| end_state = ((end & mask) == (base & mask)); |
| inclusive = ((start < base) && (end > base)); |
| |
| if ((start_state != end_state) || inclusive) { |
| /* |
| * We have start:end spanning across an MTRR. |
| * We split the region into either |
| * |
| * - start_state:1 |
| * (start:mtrr_end)(mtrr_end:end) |
| * - end_state:1 |
| * (start:mtrr_start)(mtrr_start:end) |
| * - inclusive:1 |
| * (start:mtrr_start)(mtrr_start:mtrr_end)(mtrr_end:end) |
| * |
| * depending on kind of overlap. |
| * |
| * Return the type of the first region and a pointer |
| * to the start of next region so that caller will be |
| * advised to lookup again after having adjusted start |
| * and end. |
| * |
| * Note: This way we handle overlaps with multiple |
| * entries and the default type properly. |
| */ |
| if (start_state) |
| *partial_end = base + get_mtrr_size(mask); |
| else |
| *partial_end = base; |
| |
| if (unlikely(*partial_end <= start)) { |
| WARN_ON(1); |
| *partial_end = start + PAGE_SIZE; |
| } |
| |
| end = *partial_end - 1; /* end is inclusive */ |
| *repeat = 1; |
| *uniform = 0; |
| } |
| |
| if ((start & mask) != (base & mask)) |
| continue; |
| |
| curr_match = mtrr_state.var_ranges[i].base_lo & 0xff; |
| if (prev_match == MTRR_TYPE_INVALID) { |
| prev_match = curr_match; |
| continue; |
| } |
| |
| *uniform = 0; |
| if (check_type_overlap(&prev_match, &curr_match)) |
| return curr_match; |
| } |
| |
| if (prev_match != MTRR_TYPE_INVALID) |
| return prev_match; |
| |
| return mtrr_state.def_type; |
| } |
| |
| /** |
| * mtrr_type_lookup - look up memory type in MTRR |
| * |
| * Return Values: |
| * MTRR_TYPE_(type) - The effective MTRR type for the region |
| * MTRR_TYPE_INVALID - MTRR is disabled |
| * |
| * Output Argument: |
| * uniform - Set to 1 when an MTRR covers the region uniformly, i.e. the |
| * region is fully covered by a single MTRR entry or the default |
| * type. |
| */ |
| u8 mtrr_type_lookup(u64 start, u64 end, u8 *uniform) |
| { |
| u8 type, prev_type, is_uniform = 1, dummy; |
| int repeat; |
| u64 partial_end; |
| |
| if (!mtrr_state_set) |
| return MTRR_TYPE_INVALID; |
| |
| if (!(mtrr_state.enabled & MTRR_STATE_MTRR_ENABLED)) |
| return MTRR_TYPE_INVALID; |
| |
| /* |
| * Look up the fixed ranges first, which take priority over |
| * the variable ranges. |
| */ |
| if ((start < 0x100000) && |
| (mtrr_state.have_fixed) && |
| (mtrr_state.enabled & MTRR_STATE_MTRR_FIXED_ENABLED)) { |
| is_uniform = 0; |
| type = mtrr_type_lookup_fixed(start, end); |
| goto out; |
| } |
| |
| /* |
| * Look up the variable ranges. Look of multiple ranges matching |
| * this address and pick type as per MTRR precedence. |
| */ |
| type = mtrr_type_lookup_variable(start, end, &partial_end, |
| &repeat, &is_uniform); |
| |
| /* |
| * Common path is with repeat = 0. |
| * However, we can have cases where [start:end] spans across some |
| * MTRR ranges and/or the default type. Do repeated lookups for |
| * that case here. |
| */ |
| while (repeat) { |
| prev_type = type; |
| start = partial_end; |
| is_uniform = 0; |
| type = mtrr_type_lookup_variable(start, end, &partial_end, |
| &repeat, &dummy); |
| |
| if (check_type_overlap(&prev_type, &type)) |
| goto out; |
| } |
| |
| if (mtrr_tom2 && (start >= (1ULL<<32)) && (end < mtrr_tom2)) |
| type = MTRR_TYPE_WRBACK; |
| |
| out: |
| *uniform = is_uniform; |
| return type; |
| } |
| |
| /* Get the MSR pair relating to a var range */ |
| static void |
| get_mtrr_var_range(unsigned int index, struct mtrr_var_range *vr) |
| { |
| rdmsr(MTRRphysBase_MSR(index), vr->base_lo, vr->base_hi); |
| rdmsr(MTRRphysMask_MSR(index), vr->mask_lo, vr->mask_hi); |
| } |
| |
| /* Fill the MSR pair relating to a var range */ |
| void fill_mtrr_var_range(unsigned int index, |
| u32 base_lo, u32 base_hi, u32 mask_lo, u32 mask_hi) |
| { |
| struct mtrr_var_range *vr; |
| |
| vr = mtrr_state.var_ranges; |
| |
| vr[index].base_lo = base_lo; |
| vr[index].base_hi = base_hi; |
| vr[index].mask_lo = mask_lo; |
| vr[index].mask_hi = mask_hi; |
| } |
| |
| static void get_fixed_ranges(mtrr_type *frs) |
| { |
| unsigned int *p = (unsigned int *)frs; |
| int i; |
| |
| k8_check_syscfg_dram_mod_en(); |
| |
| rdmsr(MSR_MTRRfix64K_00000, p[0], p[1]); |
| |
| for (i = 0; i < 2; i++) |
| rdmsr(MSR_MTRRfix16K_80000 + i, p[2 + i * 2], p[3 + i * 2]); |
| for (i = 0; i < 8; i++) |
| rdmsr(MSR_MTRRfix4K_C0000 + i, p[6 + i * 2], p[7 + i * 2]); |
| } |
| |
| void mtrr_save_fixed_ranges(void *info) |
| { |
| if (cpu_has_mtrr) |
| get_fixed_ranges(mtrr_state.fixed_ranges); |
| } |
| |
| static unsigned __initdata last_fixed_start; |
| static unsigned __initdata last_fixed_end; |
| static mtrr_type __initdata last_fixed_type; |
| |
| static void __init print_fixed_last(void) |
| { |
| if (!last_fixed_end) |
| return; |
| |
| pr_debug(" %05X-%05X %s\n", last_fixed_start, |
| last_fixed_end - 1, mtrr_attrib_to_str(last_fixed_type)); |
| |
| last_fixed_end = 0; |
| } |
| |
| static void __init update_fixed_last(unsigned base, unsigned end, |
| mtrr_type type) |
| { |
| last_fixed_start = base; |
| last_fixed_end = end; |
| last_fixed_type = type; |
| } |
| |
| static void __init |
| print_fixed(unsigned base, unsigned step, const mtrr_type *types) |
| { |
| unsigned i; |
| |
| for (i = 0; i < 8; ++i, ++types, base += step) { |
| if (last_fixed_end == 0) { |
| update_fixed_last(base, base + step, *types); |
| continue; |
| } |
| if (last_fixed_end == base && last_fixed_type == *types) { |
| last_fixed_end = base + step; |
| continue; |
| } |
| /* new segments: gap or different type */ |
| print_fixed_last(); |
| update_fixed_last(base, base + step, *types); |
| } |
| } |
| |
| static void prepare_set(void); |
| static void post_set(void); |
| |
| static void __init print_mtrr_state(void) |
| { |
| unsigned int i; |
| int high_width; |
| |
| pr_debug("MTRR default type: %s\n", |
| mtrr_attrib_to_str(mtrr_state.def_type)); |
| if (mtrr_state.have_fixed) { |
| pr_debug("MTRR fixed ranges %sabled:\n", |
| ((mtrr_state.enabled & MTRR_STATE_MTRR_ENABLED) && |
| (mtrr_state.enabled & MTRR_STATE_MTRR_FIXED_ENABLED)) ? |
| "en" : "dis"); |
| print_fixed(0x00000, 0x10000, mtrr_state.fixed_ranges + 0); |
| for (i = 0; i < 2; ++i) |
| print_fixed(0x80000 + i * 0x20000, 0x04000, |
| mtrr_state.fixed_ranges + (i + 1) * 8); |
| for (i = 0; i < 8; ++i) |
| print_fixed(0xC0000 + i * 0x08000, 0x01000, |
| mtrr_state.fixed_ranges + (i + 3) * 8); |
| |
| /* tail */ |
| print_fixed_last(); |
| } |
| pr_debug("MTRR variable ranges %sabled:\n", |
| mtrr_state.enabled & MTRR_STATE_MTRR_ENABLED ? "en" : "dis"); |
| high_width = (__ffs64(size_or_mask) - (32 - PAGE_SHIFT) + 3) / 4; |
| |
| for (i = 0; i < num_var_ranges; ++i) { |
| if (mtrr_state.var_ranges[i].mask_lo & (1 << 11)) |
| pr_debug(" %u base %0*X%05X000 mask %0*X%05X000 %s\n", |
| i, |
| high_width, |
| mtrr_state.var_ranges[i].base_hi, |
| mtrr_state.var_ranges[i].base_lo >> 12, |
| high_width, |
| mtrr_state.var_ranges[i].mask_hi, |
| mtrr_state.var_ranges[i].mask_lo >> 12, |
| mtrr_attrib_to_str(mtrr_state.var_ranges[i].base_lo & 0xff)); |
| else |
| pr_debug(" %u disabled\n", i); |
| } |
| if (mtrr_tom2) |
| pr_debug("TOM2: %016llx aka %lldM\n", mtrr_tom2, mtrr_tom2>>20); |
| } |
| |
| /* Grab all of the MTRR state for this CPU into *state */ |
| bool __init get_mtrr_state(void) |
| { |
| struct mtrr_var_range *vrs; |
| unsigned long flags; |
| unsigned lo, dummy; |
| unsigned int i; |
| |
| vrs = mtrr_state.var_ranges; |
| |
| rdmsr(MSR_MTRRcap, lo, dummy); |
| mtrr_state.have_fixed = (lo >> 8) & 1; |
| |
| for (i = 0; i < num_var_ranges; i++) |
| get_mtrr_var_range(i, &vrs[i]); |
| if (mtrr_state.have_fixed) |
| get_fixed_ranges(mtrr_state.fixed_ranges); |
| |
| rdmsr(MSR_MTRRdefType, lo, dummy); |
| mtrr_state.def_type = (lo & 0xff); |
| mtrr_state.enabled = (lo & 0xc00) >> 10; |
| |
| if (amd_special_default_mtrr()) { |
| unsigned low, high; |
| |
| /* TOP_MEM2 */ |
| rdmsr(MSR_K8_TOP_MEM2, low, high); |
| mtrr_tom2 = high; |
| mtrr_tom2 <<= 32; |
| mtrr_tom2 |= low; |
| mtrr_tom2 &= 0xffffff800000ULL; |
| } |
| |
| print_mtrr_state(); |
| |
| mtrr_state_set = 1; |
| |
| /* PAT setup for BP. We need to go through sync steps here */ |
| local_irq_save(flags); |
| prepare_set(); |
| |
| pat_init(); |
| |
| post_set(); |
| local_irq_restore(flags); |
| |
| return !!(mtrr_state.enabled & MTRR_STATE_MTRR_ENABLED); |
| } |
| |
| /* Some BIOS's are messed up and don't set all MTRRs the same! */ |
| void __init mtrr_state_warn(void) |
| { |
| unsigned long mask = smp_changes_mask; |
| |
| if (!mask) |
| return; |
| if (mask & MTRR_CHANGE_MASK_FIXED) |
| pr_warning("mtrr: your CPUs had inconsistent fixed MTRR settings\n"); |
| if (mask & MTRR_CHANGE_MASK_VARIABLE) |
| pr_warning("mtrr: your CPUs had inconsistent variable MTRR settings\n"); |
| if (mask & MTRR_CHANGE_MASK_DEFTYPE) |
| pr_warning("mtrr: your CPUs had inconsistent MTRRdefType settings\n"); |
| |
| printk(KERN_INFO "mtrr: probably your BIOS does not setup all CPUs.\n"); |
| printk(KERN_INFO "mtrr: corrected configuration.\n"); |
| } |
| |
| /* |
| * Doesn't attempt to pass an error out to MTRR users |
| * because it's quite complicated in some cases and probably not |
| * worth it because the best error handling is to ignore it. |
| */ |
| void mtrr_wrmsr(unsigned msr, unsigned a, unsigned b) |
| { |
| if (wrmsr_safe(msr, a, b) < 0) { |
| printk(KERN_ERR |
| "MTRR: CPU %u: Writing MSR %x to %x:%x failed\n", |
| smp_processor_id(), msr, a, b); |
| } |
| } |
| |
| /** |
| * set_fixed_range - checks & updates a fixed-range MTRR if it |
| * differs from the value it should have |
| * @msr: MSR address of the MTTR which should be checked and updated |
| * @changed: pointer which indicates whether the MTRR needed to be changed |
| * @msrwords: pointer to the MSR values which the MSR should have |
| */ |
| static void set_fixed_range(int msr, bool *changed, unsigned int *msrwords) |
| { |
| unsigned lo, hi; |
| |
| rdmsr(msr, lo, hi); |
| |
| if (lo != msrwords[0] || hi != msrwords[1]) { |
| mtrr_wrmsr(msr, msrwords[0], msrwords[1]); |
| *changed = true; |
| } |
| } |
| |
| /** |
| * generic_get_free_region - Get a free MTRR. |
| * @base: The starting (base) address of the region. |
| * @size: The size (in bytes) of the region. |
| * @replace_reg: mtrr index to be replaced; set to invalid value if none. |
| * |
| * Returns: The index of the region on success, else negative on error. |
| */ |
| int |
| generic_get_free_region(unsigned long base, unsigned long size, int replace_reg) |
| { |
| unsigned long lbase, lsize; |
| mtrr_type ltype; |
| int i, max; |
| |
| max = num_var_ranges; |
| if (replace_reg >= 0 && replace_reg < max) |
| return replace_reg; |
| |
| for (i = 0; i < max; ++i) { |
| mtrr_if->get(i, &lbase, &lsize, <ype); |
| if (lsize == 0) |
| return i; |
| } |
| |
| return -ENOSPC; |
| } |
| |
| static void generic_get_mtrr(unsigned int reg, unsigned long *base, |
| unsigned long *size, mtrr_type *type) |
| { |
| u32 mask_lo, mask_hi, base_lo, base_hi; |
| unsigned int hi; |
| u64 tmp, mask; |
| |
| /* |
| * get_mtrr doesn't need to update mtrr_state, also it could be called |
| * from any cpu, so try to print it out directly. |
| */ |
| get_cpu(); |
| |
| rdmsr(MTRRphysMask_MSR(reg), mask_lo, mask_hi); |
| |
| if ((mask_lo & 0x800) == 0) { |
| /* Invalid (i.e. free) range */ |
| *base = 0; |
| *size = 0; |
| *type = 0; |
| goto out_put_cpu; |
| } |
| |
| rdmsr(MTRRphysBase_MSR(reg), base_lo, base_hi); |
| |
| /* Work out the shifted address mask: */ |
| tmp = (u64)mask_hi << (32 - PAGE_SHIFT) | mask_lo >> PAGE_SHIFT; |
| mask = size_or_mask | tmp; |
| |
| /* Expand tmp with high bits to all 1s: */ |
| hi = fls64(tmp); |
| if (hi > 0) { |
| tmp |= ~((1ULL<<(hi - 1)) - 1); |
| |
| if (tmp != mask) { |
| printk(KERN_WARNING "mtrr: your BIOS has configured an incorrect mask, fixing it.\n"); |
| add_taint(TAINT_FIRMWARE_WORKAROUND, LOCKDEP_STILL_OK); |
| mask = tmp; |
| } |
| } |
| |
| /* |
| * This works correctly if size is a power of two, i.e. a |
| * contiguous range: |
| */ |
| *size = -mask; |
| *base = (u64)base_hi << (32 - PAGE_SHIFT) | base_lo >> PAGE_SHIFT; |
| *type = base_lo & 0xff; |
| |
| out_put_cpu: |
| put_cpu(); |
| } |
| |
| /** |
| * set_fixed_ranges - checks & updates the fixed-range MTRRs if they |
| * differ from the saved set |
| * @frs: pointer to fixed-range MTRR values, saved by get_fixed_ranges() |
| */ |
| static int set_fixed_ranges(mtrr_type *frs) |
| { |
| unsigned long long *saved = (unsigned long long *)frs; |
| bool changed = false; |
| int block = -1, range; |
| |
| k8_check_syscfg_dram_mod_en(); |
| |
| while (fixed_range_blocks[++block].ranges) { |
| for (range = 0; range < fixed_range_blocks[block].ranges; range++) |
| set_fixed_range(fixed_range_blocks[block].base_msr + range, |
| &changed, (unsigned int *)saved++); |
| } |
| |
| return changed; |
| } |
| |
| /* |
| * Set the MSR pair relating to a var range. |
| * Returns true if changes are made. |
| */ |
| static bool set_mtrr_var_ranges(unsigned int index, struct mtrr_var_range *vr) |
| { |
| unsigned int lo, hi; |
| bool changed = false; |
| |
| rdmsr(MTRRphysBase_MSR(index), lo, hi); |
| if ((vr->base_lo & 0xfffff0ffUL) != (lo & 0xfffff0ffUL) |
| || (vr->base_hi & (size_and_mask >> (32 - PAGE_SHIFT))) != |
| (hi & (size_and_mask >> (32 - PAGE_SHIFT)))) { |
| |
| mtrr_wrmsr(MTRRphysBase_MSR(index), vr->base_lo, vr->base_hi); |
| changed = true; |
| } |
| |
| rdmsr(MTRRphysMask_MSR(index), lo, hi); |
| |
| if ((vr->mask_lo & 0xfffff800UL) != (lo & 0xfffff800UL) |
| || (vr->mask_hi & (size_and_mask >> (32 - PAGE_SHIFT))) != |
| (hi & (size_and_mask >> (32 - PAGE_SHIFT)))) { |
| mtrr_wrmsr(MTRRphysMask_MSR(index), vr->mask_lo, vr->mask_hi); |
| changed = true; |
| } |
| return changed; |
| } |
| |
| static u32 deftype_lo, deftype_hi; |
| |
| /** |
| * set_mtrr_state - Set the MTRR state for this CPU. |
| * |
| * NOTE: The CPU must already be in a safe state for MTRR changes. |
| * RETURNS: 0 if no changes made, else a mask indicating what was changed. |
| */ |
| static unsigned long set_mtrr_state(void) |
| { |
| unsigned long change_mask = 0; |
| unsigned int i; |
| |
| for (i = 0; i < num_var_ranges; i++) { |
| if (set_mtrr_var_ranges(i, &mtrr_state.var_ranges[i])) |
| change_mask |= MTRR_CHANGE_MASK_VARIABLE; |
| } |
| |
| if (mtrr_state.have_fixed && set_fixed_ranges(mtrr_state.fixed_ranges)) |
| change_mask |= MTRR_CHANGE_MASK_FIXED; |
| |
| /* |
| * Set_mtrr_restore restores the old value of MTRRdefType, |
| * so to set it we fiddle with the saved value: |
| */ |
| if ((deftype_lo & 0xff) != mtrr_state.def_type |
| || ((deftype_lo & 0xc00) >> 10) != mtrr_state.enabled) { |
| |
| deftype_lo = (deftype_lo & ~0xcff) | mtrr_state.def_type | |
| (mtrr_state.enabled << 10); |
| change_mask |= MTRR_CHANGE_MASK_DEFTYPE; |
| } |
| |
| return change_mask; |
| } |
| |
| |
| static unsigned long cr4; |
| static DEFINE_RAW_SPINLOCK(set_atomicity_lock); |
| |
| /* |
| * Since we are disabling the cache don't allow any interrupts, |
| * they would run extremely slow and would only increase the pain. |
| * |
| * The caller must ensure that local interrupts are disabled and |
| * are reenabled after post_set() has been called. |
| */ |
| static void prepare_set(void) __acquires(set_atomicity_lock) |
| { |
| unsigned long cr0; |
| |
| /* |
| * Note that this is not ideal |
| * since the cache is only flushed/disabled for this CPU while the |
| * MTRRs are changed, but changing this requires more invasive |
| * changes to the way the kernel boots |
| */ |
| |
| raw_spin_lock(&set_atomicity_lock); |
| |
| /* Enter the no-fill (CD=1, NW=0) cache mode and flush caches. */ |
| cr0 = read_cr0() | X86_CR0_CD; |
| write_cr0(cr0); |
| wbinvd(); |
| |
| /* Save value of CR4 and clear Page Global Enable (bit 7) */ |
| if (cpu_has_pge) { |
| cr4 = __read_cr4(); |
| __write_cr4(cr4 & ~X86_CR4_PGE); |
| } |
| |
| /* Flush all TLBs via a mov %cr3, %reg; mov %reg, %cr3 */ |
| count_vm_tlb_event(NR_TLB_LOCAL_FLUSH_ALL); |
| __flush_tlb(); |
| |
| /* Save MTRR state */ |
| rdmsr(MSR_MTRRdefType, deftype_lo, deftype_hi); |
| |
| /* Disable MTRRs, and set the default type to uncached */ |
| mtrr_wrmsr(MSR_MTRRdefType, deftype_lo & ~0xcff, deftype_hi); |
| wbinvd(); |
| } |
| |
| static void post_set(void) __releases(set_atomicity_lock) |
| { |
| /* Flush TLBs (no need to flush caches - they are disabled) */ |
| count_vm_tlb_event(NR_TLB_LOCAL_FLUSH_ALL); |
| __flush_tlb(); |
| |
| /* Intel (P6) standard MTRRs */ |
| mtrr_wrmsr(MSR_MTRRdefType, deftype_lo, deftype_hi); |
| |
| /* Enable caches */ |
| write_cr0(read_cr0() & ~X86_CR0_CD); |
| |
| /* Restore value of CR4 */ |
| if (cpu_has_pge) |
| __write_cr4(cr4); |
| raw_spin_unlock(&set_atomicity_lock); |
| } |
| |
| static void generic_set_all(void) |
| { |
| unsigned long mask, count; |
| unsigned long flags; |
| |
| local_irq_save(flags); |
| prepare_set(); |
| |
| /* Actually set the state */ |
| mask = set_mtrr_state(); |
| |
| /* also set PAT */ |
| pat_init(); |
| |
| post_set(); |
| local_irq_restore(flags); |
| |
| /* Use the atomic bitops to update the global mask */ |
| for (count = 0; count < sizeof mask * 8; ++count) { |
| if (mask & 0x01) |
| set_bit(count, &smp_changes_mask); |
| mask >>= 1; |
| } |
| |
| } |
| |
| /** |
| * generic_set_mtrr - set variable MTRR register on the local CPU. |
| * |
| * @reg: The register to set. |
| * @base: The base address of the region. |
| * @size: The size of the region. If this is 0 the region is disabled. |
| * @type: The type of the region. |
| * |
| * Returns nothing. |
| */ |
| static void generic_set_mtrr(unsigned int reg, unsigned long base, |
| unsigned long size, mtrr_type type) |
| { |
| unsigned long flags; |
| struct mtrr_var_range *vr; |
| |
| vr = &mtrr_state.var_ranges[reg]; |
| |
| local_irq_save(flags); |
| prepare_set(); |
| |
| if (size == 0) { |
| /* |
| * The invalid bit is kept in the mask, so we simply |
| * clear the relevant mask register to disable a range. |
| */ |
| mtrr_wrmsr(MTRRphysMask_MSR(reg), 0, 0); |
| memset(vr, 0, sizeof(struct mtrr_var_range)); |
| } else { |
| vr->base_lo = base << PAGE_SHIFT | type; |
| vr->base_hi = (base & size_and_mask) >> (32 - PAGE_SHIFT); |
| vr->mask_lo = -size << PAGE_SHIFT | 0x800; |
| vr->mask_hi = (-size & size_and_mask) >> (32 - PAGE_SHIFT); |
| |
| mtrr_wrmsr(MTRRphysBase_MSR(reg), vr->base_lo, vr->base_hi); |
| mtrr_wrmsr(MTRRphysMask_MSR(reg), vr->mask_lo, vr->mask_hi); |
| } |
| |
| post_set(); |
| local_irq_restore(flags); |
| } |
| |
| int generic_validate_add_page(unsigned long base, unsigned long size, |
| unsigned int type) |
| { |
| unsigned long lbase, last; |
| |
| /* |
| * For Intel PPro stepping <= 7 |
| * must be 4 MiB aligned and not touch 0x70000000 -> 0x7003FFFF |
| */ |
| if (is_cpu(INTEL) && boot_cpu_data.x86 == 6 && |
| boot_cpu_data.x86_model == 1 && |
| boot_cpu_data.x86_mask <= 7) { |
| if (base & ((1 << (22 - PAGE_SHIFT)) - 1)) { |
| pr_warning("mtrr: base(0x%lx000) is not 4 MiB aligned\n", base); |
| return -EINVAL; |
| } |
| if (!(base + size < 0x70000 || base > 0x7003F) && |
| (type == MTRR_TYPE_WRCOMB |
| || type == MTRR_TYPE_WRBACK)) { |
| pr_warning("mtrr: writable mtrr between 0x70000000 and 0x7003FFFF may hang the CPU.\n"); |
| return -EINVAL; |
| } |
| } |
| |
| /* |
| * Check upper bits of base and last are equal and lower bits are 0 |
| * for base and 1 for last |
| */ |
| last = base + size - 1; |
| for (lbase = base; !(lbase & 1) && (last & 1); |
| lbase = lbase >> 1, last = last >> 1) |
| ; |
| if (lbase != last) { |
| pr_warning("mtrr: base(0x%lx000) is not aligned on a size(0x%lx000) boundary\n", base, size); |
| return -EINVAL; |
| } |
| return 0; |
| } |
| |
| static int generic_have_wrcomb(void) |
| { |
| unsigned long config, dummy; |
| rdmsr(MSR_MTRRcap, config, dummy); |
| return config & (1 << 10); |
| } |
| |
| int positive_have_wrcomb(void) |
| { |
| return 1; |
| } |
| |
| /* |
| * Generic structure... |
| */ |
| const struct mtrr_ops generic_mtrr_ops = { |
| .use_intel_if = 1, |
| .set_all = generic_set_all, |
| .get = generic_get_mtrr, |
| .get_free_region = generic_get_free_region, |
| .set = generic_set_mtrr, |
| .validate_add_page = generic_validate_add_page, |
| .have_wrcomb = generic_have_wrcomb, |
| }; |