Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.yaml

# SPDX-License-Identifier: GPL-2.0-only
%YAML 1.2
---
$id: http://devicetree.org/schemas/spi/snps,dw-apb-ssi.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#

title: Synopsys DesignWare AMBA 2.0 Synchronous Serial Interface

maintainers:
  - Mark Brown <broonie@kernel.org>

allOf:
  - $ref: "spi-controller.yaml#"
  - if:
      properties:
        compatible:
          contains:
            enum:
              - mscc,ocelot-spi
              - mscc,jaguar2-spi
    then:
      properties:
        reg:
          minItems: 2
  - if:
      properties:
        compatible:
          contains:
            enum:
              - baikal,bt1-sys-ssi
    then:
      properties:
        mux-controls:
          maxItems: 1
      required:
        - mux-controls
    else:
      required:
        - interrupts

properties:
  compatible:
    oneOf:
      - description: Generic DW SPI Controller
        enum:
          - snps,dw-apb-ssi
          - snps,dwc-ssi-1.01a
      - description: Microsemi Ocelot/Jaguar2 SoC SPI Controller
        items:
          - enum:
              - mscc,ocelot-spi
              - mscc,jaguar2-spi
          - const: snps,dw-apb-ssi
      - description: Microchip Sparx5 SoC SPI Controller
        const: microchip,sparx5-spi
      - description: Amazon Alpine SPI Controller
        const: amazon,alpine-dw-apb-ssi
      - description: Renesas RZ/N1 SPI Controller
        items:
          - const: renesas,rzn1-spi
          - const: snps,dw-apb-ssi
      - description: Intel Keem Bay SPI Controller
        const: intel,keembay-ssi
      - description: Baikal-T1 SPI Controller
        const: baikal,bt1-ssi
      - description: Baikal-T1 System Boot SPI Controller
        const: baikal,bt1-sys-ssi
      - description: Canaan Kendryte K210 SoS SPI Controller
        const: canaan,k210-spi
      - description: Renesas RZ/N1 SPI Controller
        items:
          - enum:
              - renesas,r9a06g032-spi # RZ/N1D
              - renesas,r9a06g033-spi # RZ/N1S
          - const: renesas,rzn1-spi   # RZ/N1

  reg:
    minItems: 1
    items:
      - description: DW APB SSI controller memory mapped registers
      - description: SPI MST region map or directly mapped SPI ROM

  interrupts:
    maxItems: 1

  clocks:
    minItems: 1
    items:
      - description: SPI Controller reference clock source
      - description: APB interface clock source

  clock-names:
    minItems: 1
    items:
      - const: ssi_clk
      - const: pclk

  resets:
    maxItems: 1

  reset-names:
    const: spi

  reg-io-width:
    $ref: /schemas/types.yaml#/definitions/uint32
    description: I/O register width (in bytes) implemented by this device
    default: 4
    enum: [ 2, 4 ]

  num-cs:
    default: 4
    minimum: 1
    maximum: 4

  dmas:
    items:
      - description: TX DMA Channel
      - description: RX DMA Channel

  dma-names:
    items:
      - const: tx
      - const: rx

  rx-sample-delay-ns:
    default: 0
    description: Default value of the rx-sample-delay-ns property.
      This value will be used if the property is not explicitly defined
      for a SPI slave device. See below.

patternProperties:
  "^.*@[0-9a-f]+$":
    type: object
    properties:
      reg:
        minimum: 0
        maximum: 3

      spi-rx-bus-width:
        const: 1

      spi-tx-bus-width:
        const: 1

      rx-sample-delay-ns:
        description: SPI Rx sample delay offset, unit is nanoseconds.
          The delay from the default sample time before the actual
          sample of the rxd input signal occurs. The "rx_sample_delay"
          is an optional feature of the designware controller, and the
          upper limit is also subject to controller configuration.

unevaluatedProperties: false

required:
  - compatible
  - reg
  - "#address-cells"
  - "#size-cells"
  - clocks

examples:
  - |
    spi@fff00000 {
      compatible = "snps,dw-apb-ssi";
      reg = <0xfff00000 0x1000>;
      #address-cells = <1>;
      #size-cells = <0>;
      interrupts = <0 154 4>;
      clocks = <&spi_m_clk>;
      num-cs = <2>;
      cs-gpios = <&gpio0 13 0>,
                 <&gpio0 14 0>;
      rx-sample-delay-ns = <3>;
      spi-flash@1 {
        compatible = "spi-nand";
        reg = <1>;
        rx-sample-delay-ns = <7>;
      };
    };
  - |
    spi@1f040100 {
      compatible = "baikal,bt1-sys-ssi";
      reg = <0x1f040100 0x900>,
            <0x1c000000 0x1000000>;
      #address-cells = <1>;
      #size-cells = <0>;
      mux-controls = <&boot_mux>;
      clocks = <&ccu_sys>;
      clock-names = "ssi_clk";
    };
...