| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Copyright (C) 2017,2020 Intel Corporation |
| * |
| * Based partially on Intel IPU4 driver written by |
| * Sakari Ailus <sakari.ailus@linux.intel.com> |
| * Samu Onkalo |
| * Jouni Högander <jouni.hogander@intel.com> |
| * Jouni Ukkonen |
| * Antti Laakso <antti.laakso@intel.com> |
| * et al. |
| */ |
| |
| #include <linux/bitops.h> |
| #include <linux/delay.h> |
| #include <linux/interrupt.h> |
| #include <linux/iopoll.h> |
| #include <linux/mm.h> |
| #include <linux/module.h> |
| #include <linux/pci.h> |
| #include <linux/pfn.h> |
| #include <linux/pm_runtime.h> |
| #include <linux/property.h> |
| #include <linux/vmalloc.h> |
| |
| #include <media/ipu-bridge.h> |
| #include <media/v4l2-ctrls.h> |
| #include <media/v4l2-device.h> |
| #include <media/v4l2-event.h> |
| #include <media/v4l2-fwnode.h> |
| #include <media/v4l2-mc.h> |
| #include <media/v4l2-ioctl.h> |
| #include <media/videobuf2-dma-sg.h> |
| |
| #include "ipu3-cio2.h" |
| |
| struct ipu3_cio2_fmt { |
| u32 mbus_code; |
| u32 fourcc; |
| u8 mipicode; |
| u8 bpp; |
| }; |
| |
| /* |
| * These are raw formats used in Intel's third generation of |
| * Image Processing Unit known as IPU3. |
| * 10bit raw bayer packed, 32 bytes for every 25 pixels, |
| * last LSB 6 bits unused. |
| */ |
| static const struct ipu3_cio2_fmt formats[] = { |
| { /* put default entry at beginning */ |
| .mbus_code = MEDIA_BUS_FMT_SGRBG10_1X10, |
| .fourcc = V4L2_PIX_FMT_IPU3_SGRBG10, |
| .mipicode = 0x2b, |
| .bpp = 10, |
| }, { |
| .mbus_code = MEDIA_BUS_FMT_SGBRG10_1X10, |
| .fourcc = V4L2_PIX_FMT_IPU3_SGBRG10, |
| .mipicode = 0x2b, |
| .bpp = 10, |
| }, { |
| .mbus_code = MEDIA_BUS_FMT_SBGGR10_1X10, |
| .fourcc = V4L2_PIX_FMT_IPU3_SBGGR10, |
| .mipicode = 0x2b, |
| .bpp = 10, |
| }, { |
| .mbus_code = MEDIA_BUS_FMT_SRGGB10_1X10, |
| .fourcc = V4L2_PIX_FMT_IPU3_SRGGB10, |
| .mipicode = 0x2b, |
| .bpp = 10, |
| }, { |
| .mbus_code = MEDIA_BUS_FMT_Y10_1X10, |
| .fourcc = V4L2_PIX_FMT_IPU3_Y10, |
| .mipicode = 0x2b, |
| .bpp = 10, |
| }, |
| }; |
| |
| /* |
| * cio2_find_format - lookup color format by fourcc or/and media bus code |
| * @pixelformat: fourcc to match, ignored if null |
| * @mbus_code: media bus code to match, ignored if null |
| */ |
| static const struct ipu3_cio2_fmt *cio2_find_format(const u32 *pixelformat, |
| const u32 *mbus_code) |
| { |
| unsigned int i; |
| |
| for (i = 0; i < ARRAY_SIZE(formats); i++) { |
| if (pixelformat && *pixelformat != formats[i].fourcc) |
| continue; |
| if (mbus_code && *mbus_code != formats[i].mbus_code) |
| continue; |
| |
| return &formats[i]; |
| } |
| |
| return NULL; |
| } |
| |
| static inline u32 cio2_bytesperline(const unsigned int width) |
| { |
| /* |
| * 64 bytes for every 50 pixels, the line length |
| * in bytes is multiple of 64 (line end alignment). |
| */ |
| return DIV_ROUND_UP(width, 50) * 64; |
| } |
| |
| /**************** FBPT operations ****************/ |
| |
| static void cio2_fbpt_exit_dummy(struct cio2_device *cio2) |
| { |
| struct device *dev = &cio2->pci_dev->dev; |
| |
| if (cio2->dummy_lop) { |
| dma_free_coherent(dev, PAGE_SIZE, cio2->dummy_lop, |
| cio2->dummy_lop_bus_addr); |
| cio2->dummy_lop = NULL; |
| } |
| if (cio2->dummy_page) { |
| dma_free_coherent(dev, PAGE_SIZE, cio2->dummy_page, |
| cio2->dummy_page_bus_addr); |
| cio2->dummy_page = NULL; |
| } |
| } |
| |
| static int cio2_fbpt_init_dummy(struct cio2_device *cio2) |
| { |
| struct device *dev = &cio2->pci_dev->dev; |
| unsigned int i; |
| |
| cio2->dummy_page = dma_alloc_coherent(dev, PAGE_SIZE, |
| &cio2->dummy_page_bus_addr, |
| GFP_KERNEL); |
| cio2->dummy_lop = dma_alloc_coherent(dev, PAGE_SIZE, |
| &cio2->dummy_lop_bus_addr, |
| GFP_KERNEL); |
| if (!cio2->dummy_page || !cio2->dummy_lop) { |
| cio2_fbpt_exit_dummy(cio2); |
| return -ENOMEM; |
| } |
| /* |
| * List of Pointers(LOP) contains 1024x32b pointers to 4KB page each |
| * Initialize each entry to dummy_page bus base address. |
| */ |
| for (i = 0; i < CIO2_LOP_ENTRIES; i++) |
| cio2->dummy_lop[i] = PFN_DOWN(cio2->dummy_page_bus_addr); |
| |
| return 0; |
| } |
| |
| static void cio2_fbpt_entry_enable(struct cio2_device *cio2, |
| struct cio2_fbpt_entry entry[CIO2_MAX_LOPS]) |
| { |
| /* |
| * The CPU first initializes some fields in fbpt, then sets |
| * the VALID bit, this barrier is to ensure that the DMA(device) |
| * does not see the VALID bit enabled before other fields are |
| * initialized; otherwise it could lead to havoc. |
| */ |
| dma_wmb(); |
| |
| /* |
| * Request interrupts for start and completion |
| * Valid bit is applicable only to 1st entry |
| */ |
| entry[0].first_entry.ctrl = CIO2_FBPT_CTRL_VALID | |
| CIO2_FBPT_CTRL_IOC | CIO2_FBPT_CTRL_IOS; |
| } |
| |
| /* Initialize fpbt entries to point to dummy frame */ |
| static void cio2_fbpt_entry_init_dummy(struct cio2_device *cio2, |
| struct cio2_fbpt_entry |
| entry[CIO2_MAX_LOPS]) |
| { |
| unsigned int i; |
| |
| entry[0].first_entry.first_page_offset = 0; |
| entry[1].second_entry.num_of_pages = CIO2_LOP_ENTRIES * CIO2_MAX_LOPS; |
| entry[1].second_entry.last_page_available_bytes = PAGE_SIZE - 1; |
| |
| for (i = 0; i < CIO2_MAX_LOPS; i++) |
| entry[i].lop_page_addr = PFN_DOWN(cio2->dummy_lop_bus_addr); |
| |
| cio2_fbpt_entry_enable(cio2, entry); |
| } |
| |
| /* Initialize fpbt entries to point to a given buffer */ |
| static void cio2_fbpt_entry_init_buf(struct cio2_device *cio2, |
| struct cio2_buffer *b, |
| struct cio2_fbpt_entry |
| entry[CIO2_MAX_LOPS]) |
| { |
| struct vb2_buffer *vb = &b->vbb.vb2_buf; |
| unsigned int length = vb->planes[0].length; |
| int remaining, i; |
| |
| entry[0].first_entry.first_page_offset = b->offset; |
| remaining = length + entry[0].first_entry.first_page_offset; |
| entry[1].second_entry.num_of_pages = PFN_UP(remaining); |
| /* |
| * last_page_available_bytes has the offset of the last byte in the |
| * last page which is still accessible by DMA. DMA cannot access |
| * beyond this point. Valid range for this is from 0 to 4095. |
| * 0 indicates 1st byte in the page is DMA accessible. |
| * 4095 (PAGE_SIZE - 1) means every single byte in the last page |
| * is available for DMA transfer. |
| */ |
| remaining = offset_in_page(remaining) ?: PAGE_SIZE; |
| entry[1].second_entry.last_page_available_bytes = remaining - 1; |
| /* Fill FBPT */ |
| remaining = length; |
| i = 0; |
| while (remaining > 0) { |
| entry->lop_page_addr = PFN_DOWN(b->lop_bus_addr[i]); |
| remaining -= CIO2_LOP_ENTRIES * PAGE_SIZE; |
| entry++; |
| i++; |
| } |
| |
| /* |
| * The first not meaningful FBPT entry should point to a valid LOP |
| */ |
| entry->lop_page_addr = PFN_DOWN(cio2->dummy_lop_bus_addr); |
| |
| cio2_fbpt_entry_enable(cio2, entry); |
| } |
| |
| static int cio2_fbpt_init(struct cio2_device *cio2, struct cio2_queue *q) |
| { |
| struct device *dev = &cio2->pci_dev->dev; |
| |
| q->fbpt = dma_alloc_coherent(dev, CIO2_FBPT_SIZE, &q->fbpt_bus_addr, |
| GFP_KERNEL); |
| if (!q->fbpt) |
| return -ENOMEM; |
| |
| return 0; |
| } |
| |
| static void cio2_fbpt_exit(struct cio2_queue *q, struct device *dev) |
| { |
| dma_free_coherent(dev, CIO2_FBPT_SIZE, q->fbpt, q->fbpt_bus_addr); |
| } |
| |
| /**************** CSI2 hardware setup ****************/ |
| |
| /* |
| * The CSI2 receiver has several parameters affecting |
| * the receiver timings. These depend on the MIPI bus frequency |
| * F in Hz (sensor transmitter rate) as follows: |
| * register value = (A/1e9 + B * UI) / COUNT_ACC |
| * where |
| * UI = 1 / (2 * F) in seconds |
| * COUNT_ACC = counter accuracy in seconds |
| * For IPU3 COUNT_ACC = 0.0625 |
| * |
| * A and B are coefficients from the table below, |
| * depending whether the register minimum or maximum value is |
| * calculated. |
| * Minimum Maximum |
| * Clock lane A B A B |
| * reg_rx_csi_dly_cnt_termen_clane 0 0 38 0 |
| * reg_rx_csi_dly_cnt_settle_clane 95 -8 300 -16 |
| * Data lanes |
| * reg_rx_csi_dly_cnt_termen_dlane0 0 0 35 4 |
| * reg_rx_csi_dly_cnt_settle_dlane0 85 -2 145 -6 |
| * reg_rx_csi_dly_cnt_termen_dlane1 0 0 35 4 |
| * reg_rx_csi_dly_cnt_settle_dlane1 85 -2 145 -6 |
| * reg_rx_csi_dly_cnt_termen_dlane2 0 0 35 4 |
| * reg_rx_csi_dly_cnt_settle_dlane2 85 -2 145 -6 |
| * reg_rx_csi_dly_cnt_termen_dlane3 0 0 35 4 |
| * reg_rx_csi_dly_cnt_settle_dlane3 85 -2 145 -6 |
| * |
| * We use the minimum values of both A and B. |
| */ |
| |
| /* |
| * shift for keeping value range suitable for 32-bit integer arithmetic |
| */ |
| #define LIMIT_SHIFT 8 |
| |
| static s32 cio2_rx_timing(s32 a, s32 b, s64 freq, int def) |
| { |
| const u32 accinv = 16; /* invert of counter resolution */ |
| const u32 uiinv = 500000000; /* 1e9 / 2 */ |
| s32 r; |
| |
| freq >>= LIMIT_SHIFT; |
| |
| if (WARN_ON(freq <= 0 || freq > S32_MAX)) |
| return def; |
| /* |
| * b could be 0, -2 or -8, so |accinv * b| is always |
| * less than (1 << ds) and thus |r| < 500000000. |
| */ |
| r = accinv * b * (uiinv >> LIMIT_SHIFT); |
| r = r / (s32)freq; |
| /* max value of a is 95 */ |
| r += accinv * a; |
| |
| return r; |
| }; |
| |
| /* Calculate the delay value for termination enable of clock lane HS Rx */ |
| static int cio2_csi2_calc_timing(struct cio2_device *cio2, struct cio2_queue *q, |
| struct cio2_csi2_timing *timing, |
| unsigned int bpp, unsigned int lanes) |
| { |
| struct device *dev = &cio2->pci_dev->dev; |
| s64 freq; |
| |
| if (!q->sensor) |
| return -ENODEV; |
| |
| freq = v4l2_get_link_freq(q->sensor->ctrl_handler, bpp, lanes * 2); |
| if (freq < 0) { |
| dev_err(dev, "error %lld, invalid link_freq\n", freq); |
| return freq; |
| } |
| |
| timing->clk_termen = cio2_rx_timing(CIO2_CSIRX_DLY_CNT_TERMEN_CLANE_A, |
| CIO2_CSIRX_DLY_CNT_TERMEN_CLANE_B, |
| freq, |
| CIO2_CSIRX_DLY_CNT_TERMEN_DEFAULT); |
| timing->clk_settle = cio2_rx_timing(CIO2_CSIRX_DLY_CNT_SETTLE_CLANE_A, |
| CIO2_CSIRX_DLY_CNT_SETTLE_CLANE_B, |
| freq, |
| CIO2_CSIRX_DLY_CNT_SETTLE_DEFAULT); |
| timing->dat_termen = cio2_rx_timing(CIO2_CSIRX_DLY_CNT_TERMEN_DLANE_A, |
| CIO2_CSIRX_DLY_CNT_TERMEN_DLANE_B, |
| freq, |
| CIO2_CSIRX_DLY_CNT_TERMEN_DEFAULT); |
| timing->dat_settle = cio2_rx_timing(CIO2_CSIRX_DLY_CNT_SETTLE_DLANE_A, |
| CIO2_CSIRX_DLY_CNT_SETTLE_DLANE_B, |
| freq, |
| CIO2_CSIRX_DLY_CNT_SETTLE_DEFAULT); |
| |
| dev_dbg(dev, "freq ct value is %d\n", timing->clk_termen); |
| dev_dbg(dev, "freq cs value is %d\n", timing->clk_settle); |
| dev_dbg(dev, "freq dt value is %d\n", timing->dat_termen); |
| dev_dbg(dev, "freq ds value is %d\n", timing->dat_settle); |
| |
| return 0; |
| }; |
| |
| static int cio2_hw_init(struct cio2_device *cio2, struct cio2_queue *q) |
| { |
| static const int NUM_VCS = 4; |
| static const int SID; /* Stream id */ |
| static const int ENTRY; |
| static const int FBPT_WIDTH = DIV_ROUND_UP(CIO2_MAX_LOPS, |
| CIO2_FBPT_SUBENTRY_UNIT); |
| const u32 num_buffers1 = CIO2_MAX_BUFFERS - 1; |
| const struct ipu3_cio2_fmt *fmt; |
| void __iomem *const base = cio2->base; |
| u8 lanes, csi2bus = q->csi2.port; |
| u8 sensor_vc = SENSOR_VIR_CH_DFLT; |
| struct cio2_csi2_timing timing = { 0 }; |
| int i, r; |
| |
| fmt = cio2_find_format(NULL, &q->subdev_fmt.code); |
| if (!fmt) |
| return -EINVAL; |
| |
| lanes = q->csi2.lanes; |
| |
| r = cio2_csi2_calc_timing(cio2, q, &timing, fmt->bpp, lanes); |
| if (r) |
| return r; |
| |
| writel(timing.clk_termen, q->csi_rx_base + |
| CIO2_REG_CSIRX_DLY_CNT_TERMEN(CIO2_CSIRX_DLY_CNT_CLANE_IDX)); |
| writel(timing.clk_settle, q->csi_rx_base + |
| CIO2_REG_CSIRX_DLY_CNT_SETTLE(CIO2_CSIRX_DLY_CNT_CLANE_IDX)); |
| |
| for (i = 0; i < lanes; i++) { |
| writel(timing.dat_termen, q->csi_rx_base + |
| CIO2_REG_CSIRX_DLY_CNT_TERMEN(i)); |
| writel(timing.dat_settle, q->csi_rx_base + |
| CIO2_REG_CSIRX_DLY_CNT_SETTLE(i)); |
| } |
| |
| writel(CIO2_PBM_WMCTRL1_MIN_2CK | |
| CIO2_PBM_WMCTRL1_MID1_2CK | |
| CIO2_PBM_WMCTRL1_MID2_2CK, base + CIO2_REG_PBM_WMCTRL1); |
| writel(CIO2_PBM_WMCTRL2_HWM_2CK << CIO2_PBM_WMCTRL2_HWM_2CK_SHIFT | |
| CIO2_PBM_WMCTRL2_LWM_2CK << CIO2_PBM_WMCTRL2_LWM_2CK_SHIFT | |
| CIO2_PBM_WMCTRL2_OBFFWM_2CK << |
| CIO2_PBM_WMCTRL2_OBFFWM_2CK_SHIFT | |
| CIO2_PBM_WMCTRL2_TRANSDYN << CIO2_PBM_WMCTRL2_TRANSDYN_SHIFT | |
| CIO2_PBM_WMCTRL2_OBFF_MEM_EN, base + CIO2_REG_PBM_WMCTRL2); |
| writel(CIO2_PBM_ARB_CTRL_LANES_DIV << |
| CIO2_PBM_ARB_CTRL_LANES_DIV_SHIFT | |
| CIO2_PBM_ARB_CTRL_LE_EN | |
| CIO2_PBM_ARB_CTRL_PLL_POST_SHTDN << |
| CIO2_PBM_ARB_CTRL_PLL_POST_SHTDN_SHIFT | |
| CIO2_PBM_ARB_CTRL_PLL_AHD_WK_UP << |
| CIO2_PBM_ARB_CTRL_PLL_AHD_WK_UP_SHIFT, |
| base + CIO2_REG_PBM_ARB_CTRL); |
| writel(CIO2_CSIRX_STATUS_DLANE_HS_MASK, |
| q->csi_rx_base + CIO2_REG_CSIRX_STATUS_DLANE_HS); |
| writel(CIO2_CSIRX_STATUS_DLANE_LP_MASK, |
| q->csi_rx_base + CIO2_REG_CSIRX_STATUS_DLANE_LP); |
| |
| writel(CIO2_FB_HPLL_FREQ, base + CIO2_REG_FB_HPLL_FREQ); |
| writel(CIO2_ISCLK_RATIO, base + CIO2_REG_ISCLK_RATIO); |
| |
| /* Configure MIPI backend */ |
| for (i = 0; i < NUM_VCS; i++) |
| writel(1, q->csi_rx_base + CIO2_REG_MIPIBE_SP_LUT_ENTRY(i)); |
| |
| /* There are 16 short packet LUT entry */ |
| for (i = 0; i < 16; i++) |
| writel(CIO2_MIPIBE_LP_LUT_ENTRY_DISREGARD, |
| q->csi_rx_base + CIO2_REG_MIPIBE_LP_LUT_ENTRY(i)); |
| writel(CIO2_MIPIBE_GLOBAL_LUT_DISREGARD, |
| q->csi_rx_base + CIO2_REG_MIPIBE_GLOBAL_LUT_DISREGARD); |
| |
| writel(CIO2_INT_EN_EXT_IE_MASK, base + CIO2_REG_INT_EN_EXT_IE); |
| writel(CIO2_IRQCTRL_MASK, q->csi_rx_base + CIO2_REG_IRQCTRL_MASK); |
| writel(CIO2_IRQCTRL_MASK, q->csi_rx_base + CIO2_REG_IRQCTRL_ENABLE); |
| writel(0, q->csi_rx_base + CIO2_REG_IRQCTRL_EDGE); |
| writel(0, q->csi_rx_base + CIO2_REG_IRQCTRL_LEVEL_NOT_PULSE); |
| writel(CIO2_INT_EN_EXT_OE_MASK, base + CIO2_REG_INT_EN_EXT_OE); |
| |
| writel(CIO2_REG_INT_EN_IRQ | CIO2_INT_IOC(CIO2_DMA_CHAN) | |
| CIO2_REG_INT_EN_IOS(CIO2_DMA_CHAN), |
| base + CIO2_REG_INT_EN); |
| |
| writel((CIO2_PXM_PXF_FMT_CFG_BPP_10 | CIO2_PXM_PXF_FMT_CFG_PCK_64B) |
| << CIO2_PXM_PXF_FMT_CFG_SID0_SHIFT, |
| base + CIO2_REG_PXM_PXF_FMT_CFG0(csi2bus)); |
| writel(SID << CIO2_MIPIBE_LP_LUT_ENTRY_SID_SHIFT | |
| sensor_vc << CIO2_MIPIBE_LP_LUT_ENTRY_VC_SHIFT | |
| fmt->mipicode << CIO2_MIPIBE_LP_LUT_ENTRY_FORMAT_TYPE_SHIFT, |
| q->csi_rx_base + CIO2_REG_MIPIBE_LP_LUT_ENTRY(ENTRY)); |
| writel(0, q->csi_rx_base + CIO2_REG_MIPIBE_COMP_FORMAT(sensor_vc)); |
| writel(0, q->csi_rx_base + CIO2_REG_MIPIBE_FORCE_RAW8); |
| writel(0, base + CIO2_REG_PXM_SID2BID0(csi2bus)); |
| |
| writel(lanes, q->csi_rx_base + CIO2_REG_CSIRX_NOF_ENABLED_LANES); |
| writel(CIO2_CGC_PRIM_TGE | |
| CIO2_CGC_SIDE_TGE | |
| CIO2_CGC_XOSC_TGE | |
| CIO2_CGC_D3I3_TGE | |
| CIO2_CGC_CSI2_INTERFRAME_TGE | |
| CIO2_CGC_CSI2_PORT_DCGE | |
| CIO2_CGC_SIDE_DCGE | |
| CIO2_CGC_PRIM_DCGE | |
| CIO2_CGC_ROSC_DCGE | |
| CIO2_CGC_XOSC_DCGE | |
| CIO2_CGC_CLKGATE_HOLDOFF << CIO2_CGC_CLKGATE_HOLDOFF_SHIFT | |
| CIO2_CGC_CSI_CLKGATE_HOLDOFF |
| << CIO2_CGC_CSI_CLKGATE_HOLDOFF_SHIFT, base + CIO2_REG_CGC); |
| writel(CIO2_LTRCTRL_LTRDYNEN, base + CIO2_REG_LTRCTRL); |
| writel(CIO2_LTRVAL0_VAL << CIO2_LTRVAL02_VAL_SHIFT | |
| CIO2_LTRVAL0_SCALE << CIO2_LTRVAL02_SCALE_SHIFT | |
| CIO2_LTRVAL1_VAL << CIO2_LTRVAL13_VAL_SHIFT | |
| CIO2_LTRVAL1_SCALE << CIO2_LTRVAL13_SCALE_SHIFT, |
| base + CIO2_REG_LTRVAL01); |
| writel(CIO2_LTRVAL2_VAL << CIO2_LTRVAL02_VAL_SHIFT | |
| CIO2_LTRVAL2_SCALE << CIO2_LTRVAL02_SCALE_SHIFT | |
| CIO2_LTRVAL3_VAL << CIO2_LTRVAL13_VAL_SHIFT | |
| CIO2_LTRVAL3_SCALE << CIO2_LTRVAL13_SCALE_SHIFT, |
| base + CIO2_REG_LTRVAL23); |
| |
| for (i = 0; i < CIO2_NUM_DMA_CHAN; i++) { |
| writel(0, base + CIO2_REG_CDMABA(i)); |
| writel(0, base + CIO2_REG_CDMAC0(i)); |
| writel(0, base + CIO2_REG_CDMAC1(i)); |
| } |
| |
| /* Enable DMA */ |
| writel(PFN_DOWN(q->fbpt_bus_addr), base + CIO2_REG_CDMABA(CIO2_DMA_CHAN)); |
| |
| writel(num_buffers1 << CIO2_CDMAC0_FBPT_LEN_SHIFT | |
| FBPT_WIDTH << CIO2_CDMAC0_FBPT_WIDTH_SHIFT | |
| CIO2_CDMAC0_DMA_INTR_ON_FE | |
| CIO2_CDMAC0_FBPT_UPDATE_FIFO_FULL | |
| CIO2_CDMAC0_DMA_EN | |
| CIO2_CDMAC0_DMA_INTR_ON_FS | |
| CIO2_CDMAC0_DMA_HALTED, base + CIO2_REG_CDMAC0(CIO2_DMA_CHAN)); |
| |
| writel(1 << CIO2_CDMAC1_LINENUMUPDATE_SHIFT, |
| base + CIO2_REG_CDMAC1(CIO2_DMA_CHAN)); |
| |
| writel(0, base + CIO2_REG_PBM_FOPN_ABORT); |
| |
| writel(CIO2_PXM_FRF_CFG_CRC_TH << CIO2_PXM_FRF_CFG_CRC_TH_SHIFT | |
| CIO2_PXM_FRF_CFG_MSK_ECC_DPHY_NR | |
| CIO2_PXM_FRF_CFG_MSK_ECC_RE | |
| CIO2_PXM_FRF_CFG_MSK_ECC_DPHY_NE, |
| base + CIO2_REG_PXM_FRF_CFG(q->csi2.port)); |
| |
| /* Clear interrupts */ |
| writel(CIO2_IRQCTRL_MASK, q->csi_rx_base + CIO2_REG_IRQCTRL_CLEAR); |
| writel(~0, base + CIO2_REG_INT_STS_EXT_OE); |
| writel(~0, base + CIO2_REG_INT_STS_EXT_IE); |
| writel(~0, base + CIO2_REG_INT_STS); |
| |
| /* Enable devices, starting from the last device in the pipe */ |
| writel(1, q->csi_rx_base + CIO2_REG_MIPIBE_ENABLE); |
| writel(1, q->csi_rx_base + CIO2_REG_CSIRX_ENABLE); |
| |
| return 0; |
| } |
| |
| static void cio2_hw_exit(struct cio2_device *cio2, struct cio2_queue *q) |
| { |
| struct device *dev = &cio2->pci_dev->dev; |
| void __iomem *const base = cio2->base; |
| unsigned int i; |
| u32 value; |
| int ret; |
| |
| /* Disable CSI receiver and MIPI backend devices */ |
| writel(0, q->csi_rx_base + CIO2_REG_IRQCTRL_MASK); |
| writel(0, q->csi_rx_base + CIO2_REG_IRQCTRL_ENABLE); |
| writel(0, q->csi_rx_base + CIO2_REG_CSIRX_ENABLE); |
| writel(0, q->csi_rx_base + CIO2_REG_MIPIBE_ENABLE); |
| |
| /* Halt DMA */ |
| writel(0, base + CIO2_REG_CDMAC0(CIO2_DMA_CHAN)); |
| ret = readl_poll_timeout(base + CIO2_REG_CDMAC0(CIO2_DMA_CHAN), |
| value, value & CIO2_CDMAC0_DMA_HALTED, |
| 4000, 2000000); |
| if (ret) |
| dev_err(dev, "DMA %i can not be halted\n", CIO2_DMA_CHAN); |
| |
| for (i = 0; i < CIO2_NUM_PORTS; i++) { |
| writel(readl(base + CIO2_REG_PXM_FRF_CFG(i)) | |
| CIO2_PXM_FRF_CFG_ABORT, base + CIO2_REG_PXM_FRF_CFG(i)); |
| writel(readl(base + CIO2_REG_PBM_FOPN_ABORT) | |
| CIO2_PBM_FOPN_ABORT(i), base + CIO2_REG_PBM_FOPN_ABORT); |
| } |
| } |
| |
| static void cio2_buffer_done(struct cio2_device *cio2, unsigned int dma_chan) |
| { |
| struct device *dev = &cio2->pci_dev->dev; |
| struct cio2_queue *q = cio2->cur_queue; |
| struct cio2_fbpt_entry *entry; |
| u64 ns = ktime_get_ns(); |
| |
| if (dma_chan >= CIO2_QUEUES) { |
| dev_err(dev, "bad DMA channel %i\n", dma_chan); |
| return; |
| } |
| |
| entry = &q->fbpt[q->bufs_first * CIO2_MAX_LOPS]; |
| if (entry->first_entry.ctrl & CIO2_FBPT_CTRL_VALID) { |
| dev_warn(dev, "no ready buffers found on DMA channel %u\n", |
| dma_chan); |
| return; |
| } |
| |
| /* Find out which buffer(s) are ready */ |
| do { |
| struct cio2_buffer *b; |
| |
| b = q->bufs[q->bufs_first]; |
| if (b) { |
| unsigned int received = entry[1].second_entry.num_of_bytes; |
| unsigned long payload = |
| vb2_get_plane_payload(&b->vbb.vb2_buf, 0); |
| |
| q->bufs[q->bufs_first] = NULL; |
| atomic_dec(&q->bufs_queued); |
| dev_dbg(dev, "buffer %i done\n", b->vbb.vb2_buf.index); |
| |
| b->vbb.vb2_buf.timestamp = ns; |
| b->vbb.field = V4L2_FIELD_NONE; |
| b->vbb.sequence = atomic_read(&q->frame_sequence); |
| if (payload != received) |
| dev_warn(dev, |
| "payload length is %lu, received %u\n", |
| payload, received); |
| vb2_buffer_done(&b->vbb.vb2_buf, VB2_BUF_STATE_DONE); |
| } |
| atomic_inc(&q->frame_sequence); |
| cio2_fbpt_entry_init_dummy(cio2, entry); |
| q->bufs_first = (q->bufs_first + 1) % CIO2_MAX_BUFFERS; |
| entry = &q->fbpt[q->bufs_first * CIO2_MAX_LOPS]; |
| } while (!(entry->first_entry.ctrl & CIO2_FBPT_CTRL_VALID)); |
| } |
| |
| static void cio2_queue_event_sof(struct cio2_device *cio2, struct cio2_queue *q) |
| { |
| /* |
| * For the user space camera control algorithms it is essential |
| * to know when the reception of a frame has begun. That's often |
| * the best timing information to get from the hardware. |
| */ |
| struct v4l2_event event = { |
| .type = V4L2_EVENT_FRAME_SYNC, |
| .u.frame_sync.frame_sequence = atomic_read(&q->frame_sequence), |
| }; |
| |
| v4l2_event_queue(q->subdev.devnode, &event); |
| } |
| |
| static const char *const cio2_irq_errs[] = { |
| "single packet header error corrected", |
| "multiple packet header errors detected", |
| "payload checksum (CRC) error", |
| "fifo overflow", |
| "reserved short packet data type detected", |
| "reserved long packet data type detected", |
| "incomplete long packet detected", |
| "frame sync error", |
| "line sync error", |
| "DPHY start of transmission error", |
| "DPHY synchronization error", |
| "escape mode error", |
| "escape mode trigger event", |
| "escape mode ultra-low power state for data lane(s)", |
| "escape mode ultra-low power state exit for clock lane", |
| "inter-frame short packet discarded", |
| "inter-frame long packet discarded", |
| "non-matching Long Packet stalled", |
| }; |
| |
| static void cio2_irq_log_irq_errs(struct device *dev, u8 port, u32 status) |
| { |
| unsigned long csi2_status = status; |
| unsigned int i; |
| |
| for_each_set_bit(i, &csi2_status, ARRAY_SIZE(cio2_irq_errs)) |
| dev_err(dev, "CSI-2 receiver port %i: %s\n", |
| port, cio2_irq_errs[i]); |
| |
| if (fls_long(csi2_status) >= ARRAY_SIZE(cio2_irq_errs)) |
| dev_warn(dev, "unknown CSI2 error 0x%lx on port %i\n", |
| csi2_status, port); |
| } |
| |
| static const char *const cio2_port_errs[] = { |
| "ECC recoverable", |
| "DPHY not recoverable", |
| "ECC not recoverable", |
| "CRC error", |
| "INTERFRAMEDATA", |
| "PKT2SHORT", |
| "PKT2LONG", |
| }; |
| |
| static void cio2_irq_log_port_errs(struct device *dev, u8 port, u32 status) |
| { |
| unsigned long port_status = status; |
| unsigned int i; |
| |
| for_each_set_bit(i, &port_status, ARRAY_SIZE(cio2_port_errs)) |
| dev_err(dev, "port %i error %s\n", port, cio2_port_errs[i]); |
| } |
| |
| static void cio2_irq_handle_once(struct cio2_device *cio2, u32 int_status) |
| { |
| struct device *dev = &cio2->pci_dev->dev; |
| void __iomem *const base = cio2->base; |
| |
| if (int_status & CIO2_INT_IOOE) { |
| /* |
| * Interrupt on Output Error: |
| * 1) SRAM is full and FS received, or |
| * 2) An invalid bit detected by DMA. |
| */ |
| u32 oe_status, oe_clear; |
| |
| oe_clear = readl(base + CIO2_REG_INT_STS_EXT_OE); |
| oe_status = oe_clear; |
| |
| if (oe_status & CIO2_INT_EXT_OE_DMAOE_MASK) { |
| dev_err(dev, "DMA output error: 0x%x\n", |
| (oe_status & CIO2_INT_EXT_OE_DMAOE_MASK) |
| >> CIO2_INT_EXT_OE_DMAOE_SHIFT); |
| oe_status &= ~CIO2_INT_EXT_OE_DMAOE_MASK; |
| } |
| if (oe_status & CIO2_INT_EXT_OE_OES_MASK) { |
| dev_err(dev, "DMA output error on CSI2 buses: 0x%x\n", |
| (oe_status & CIO2_INT_EXT_OE_OES_MASK) |
| >> CIO2_INT_EXT_OE_OES_SHIFT); |
| oe_status &= ~CIO2_INT_EXT_OE_OES_MASK; |
| } |
| writel(oe_clear, base + CIO2_REG_INT_STS_EXT_OE); |
| if (oe_status) |
| dev_warn(dev, "unknown interrupt 0x%x on OE\n", |
| oe_status); |
| int_status &= ~CIO2_INT_IOOE; |
| } |
| |
| if (int_status & CIO2_INT_IOC_MASK) { |
| /* DMA IO done -- frame ready */ |
| u32 clr = 0; |
| unsigned int d; |
| |
| for (d = 0; d < CIO2_NUM_DMA_CHAN; d++) |
| if (int_status & CIO2_INT_IOC(d)) { |
| clr |= CIO2_INT_IOC(d); |
| cio2_buffer_done(cio2, d); |
| } |
| int_status &= ~clr; |
| } |
| |
| if (int_status & CIO2_INT_IOS_IOLN_MASK) { |
| /* DMA IO starts or reached specified line */ |
| u32 clr = 0; |
| unsigned int d; |
| |
| for (d = 0; d < CIO2_NUM_DMA_CHAN; d++) |
| if (int_status & CIO2_INT_IOS_IOLN(d)) { |
| clr |= CIO2_INT_IOS_IOLN(d); |
| if (d == CIO2_DMA_CHAN) |
| cio2_queue_event_sof(cio2, |
| cio2->cur_queue); |
| } |
| int_status &= ~clr; |
| } |
| |
| if (int_status & (CIO2_INT_IOIE | CIO2_INT_IOIRQ)) { |
| /* CSI2 receiver (error) interrupt */ |
| unsigned int port; |
| u32 ie_status; |
| |
| ie_status = readl(base + CIO2_REG_INT_STS_EXT_IE); |
| |
| for (port = 0; port < CIO2_NUM_PORTS; port++) { |
| u32 port_status = (ie_status >> (port * 8)) & 0xff; |
| |
| cio2_irq_log_port_errs(dev, port, port_status); |
| |
| if (ie_status & CIO2_INT_EXT_IE_IRQ(port)) { |
| void __iomem *csi_rx_base = |
| base + CIO2_REG_PIPE_BASE(port); |
| u32 csi2_status; |
| |
| csi2_status = readl(csi_rx_base + |
| CIO2_REG_IRQCTRL_STATUS); |
| |
| cio2_irq_log_irq_errs(dev, port, csi2_status); |
| |
| writel(csi2_status, |
| csi_rx_base + CIO2_REG_IRQCTRL_CLEAR); |
| } |
| } |
| |
| writel(ie_status, base + CIO2_REG_INT_STS_EXT_IE); |
| |
| int_status &= ~(CIO2_INT_IOIE | CIO2_INT_IOIRQ); |
| } |
| |
| if (int_status) |
| dev_warn(dev, "unknown interrupt 0x%x on INT\n", int_status); |
| } |
| |
| static irqreturn_t cio2_irq(int irq, void *cio2_ptr) |
| { |
| struct cio2_device *cio2 = cio2_ptr; |
| void __iomem *const base = cio2->base; |
| struct device *dev = &cio2->pci_dev->dev; |
| u32 int_status; |
| |
| int_status = readl(base + CIO2_REG_INT_STS); |
| dev_dbg(dev, "isr enter - interrupt status 0x%x\n", int_status); |
| if (!int_status) |
| return IRQ_NONE; |
| |
| do { |
| writel(int_status, base + CIO2_REG_INT_STS); |
| cio2_irq_handle_once(cio2, int_status); |
| int_status = readl(base + CIO2_REG_INT_STS); |
| if (int_status) |
| dev_dbg(dev, "pending status 0x%x\n", int_status); |
| } while (int_status); |
| |
| return IRQ_HANDLED; |
| } |
| |
| /**************** Videobuf2 interface ****************/ |
| |
| static void cio2_vb2_return_all_buffers(struct cio2_queue *q, |
| enum vb2_buffer_state state) |
| { |
| unsigned int i; |
| |
| for (i = 0; i < CIO2_MAX_BUFFERS; i++) { |
| if (q->bufs[i]) { |
| atomic_dec(&q->bufs_queued); |
| vb2_buffer_done(&q->bufs[i]->vbb.vb2_buf, |
| state); |
| q->bufs[i] = NULL; |
| } |
| } |
| } |
| |
| static int cio2_vb2_queue_setup(struct vb2_queue *vq, |
| unsigned int *num_buffers, |
| unsigned int *num_planes, |
| unsigned int sizes[], |
| struct device *alloc_devs[]) |
| { |
| struct cio2_device *cio2 = vb2_get_drv_priv(vq); |
| struct device *dev = &cio2->pci_dev->dev; |
| struct cio2_queue *q = vb2q_to_cio2_queue(vq); |
| unsigned int i; |
| |
| if (*num_planes && *num_planes < q->format.num_planes) |
| return -EINVAL; |
| |
| for (i = 0; i < q->format.num_planes; ++i) { |
| if (*num_planes && sizes[i] < q->format.plane_fmt[i].sizeimage) |
| return -EINVAL; |
| sizes[i] = q->format.plane_fmt[i].sizeimage; |
| alloc_devs[i] = dev; |
| } |
| |
| *num_planes = q->format.num_planes; |
| *num_buffers = clamp_val(*num_buffers, 1, CIO2_MAX_BUFFERS); |
| |
| /* Initialize buffer queue */ |
| for (i = 0; i < CIO2_MAX_BUFFERS; i++) { |
| q->bufs[i] = NULL; |
| cio2_fbpt_entry_init_dummy(cio2, &q->fbpt[i * CIO2_MAX_LOPS]); |
| } |
| atomic_set(&q->bufs_queued, 0); |
| q->bufs_first = 0; |
| q->bufs_next = 0; |
| |
| return 0; |
| } |
| |
| /* Called after each buffer is allocated */ |
| static int cio2_vb2_buf_init(struct vb2_buffer *vb) |
| { |
| struct cio2_device *cio2 = vb2_get_drv_priv(vb->vb2_queue); |
| struct device *dev = &cio2->pci_dev->dev; |
| struct cio2_buffer *b = to_cio2_buffer(vb); |
| unsigned int pages = PFN_UP(vb->planes[0].length); |
| unsigned int lops = DIV_ROUND_UP(pages + 1, CIO2_LOP_ENTRIES); |
| struct sg_table *sg; |
| struct sg_dma_page_iter sg_iter; |
| unsigned int i, j; |
| |
| if (lops <= 0 || lops > CIO2_MAX_LOPS) { |
| dev_err(dev, "%s: bad buffer size (%i)\n", __func__, |
| vb->planes[0].length); |
| return -ENOSPC; /* Should never happen */ |
| } |
| |
| memset(b->lop, 0, sizeof(b->lop)); |
| /* Allocate LOP table */ |
| for (i = 0; i < lops; i++) { |
| b->lop[i] = dma_alloc_coherent(dev, PAGE_SIZE, |
| &b->lop_bus_addr[i], GFP_KERNEL); |
| if (!b->lop[i]) |
| goto fail; |
| } |
| |
| /* Fill LOP */ |
| sg = vb2_dma_sg_plane_desc(vb, 0); |
| if (!sg) |
| return -ENOMEM; |
| |
| if (sg->nents && sg->sgl) |
| b->offset = sg->sgl->offset; |
| |
| i = j = 0; |
| for_each_sg_dma_page(sg->sgl, &sg_iter, sg->nents, 0) { |
| if (!pages--) |
| break; |
| b->lop[i][j] = PFN_DOWN(sg_page_iter_dma_address(&sg_iter)); |
| j++; |
| if (j == CIO2_LOP_ENTRIES) { |
| i++; |
| j = 0; |
| } |
| } |
| |
| b->lop[i][j] = PFN_DOWN(cio2->dummy_page_bus_addr); |
| return 0; |
| fail: |
| while (i--) |
| dma_free_coherent(dev, PAGE_SIZE, b->lop[i], b->lop_bus_addr[i]); |
| return -ENOMEM; |
| } |
| |
| /* Transfer buffer ownership to cio2 */ |
| static void cio2_vb2_buf_queue(struct vb2_buffer *vb) |
| { |
| struct cio2_device *cio2 = vb2_get_drv_priv(vb->vb2_queue); |
| struct device *dev = &cio2->pci_dev->dev; |
| struct cio2_queue *q = |
| container_of(vb->vb2_queue, struct cio2_queue, vbq); |
| struct cio2_buffer *b = to_cio2_buffer(vb); |
| struct cio2_fbpt_entry *entry; |
| unsigned long flags; |
| unsigned int i, j, next = q->bufs_next; |
| int bufs_queued = atomic_inc_return(&q->bufs_queued); |
| u32 fbpt_rp; |
| |
| dev_dbg(dev, "queue buffer %d\n", vb->index); |
| |
| /* |
| * This code queues the buffer to the CIO2 DMA engine, which starts |
| * running once streaming has started. It is possible that this code |
| * gets pre-empted due to increased CPU load. Upon this, the driver |
| * does not get an opportunity to queue new buffers to the CIO2 DMA |
| * engine. When the DMA engine encounters an FBPT entry without the |
| * VALID bit set, the DMA engine halts, which requires a restart of |
| * the DMA engine and sensor, to continue streaming. |
| * This is not desired and is highly unlikely given that there are |
| * 32 FBPT entries that the DMA engine needs to process, to run into |
| * an FBPT entry, without the VALID bit set. We try to mitigate this |
| * by disabling interrupts for the duration of this queueing. |
| */ |
| local_irq_save(flags); |
| |
| fbpt_rp = (readl(cio2->base + CIO2_REG_CDMARI(CIO2_DMA_CHAN)) |
| >> CIO2_CDMARI_FBPT_RP_SHIFT) |
| & CIO2_CDMARI_FBPT_RP_MASK; |
| |
| /* |
| * fbpt_rp is the fbpt entry that the dma is currently working |
| * on, but since it could jump to next entry at any time, |
| * assume that we might already be there. |
| */ |
| fbpt_rp = (fbpt_rp + 1) % CIO2_MAX_BUFFERS; |
| |
| if (bufs_queued <= 1 || fbpt_rp == next) |
| /* Buffers were drained */ |
| next = (fbpt_rp + 1) % CIO2_MAX_BUFFERS; |
| |
| for (i = 0; i < CIO2_MAX_BUFFERS; i++) { |
| /* |
| * We have allocated CIO2_MAX_BUFFERS circularly for the |
| * hw, the user has requested N buffer queue. The driver |
| * ensures N <= CIO2_MAX_BUFFERS and guarantees that whenever |
| * user queues a buffer, there necessarily is a free buffer. |
| */ |
| if (!q->bufs[next]) { |
| q->bufs[next] = b; |
| entry = &q->fbpt[next * CIO2_MAX_LOPS]; |
| cio2_fbpt_entry_init_buf(cio2, b, entry); |
| local_irq_restore(flags); |
| q->bufs_next = (next + 1) % CIO2_MAX_BUFFERS; |
| for (j = 0; j < vb->num_planes; j++) |
| vb2_set_plane_payload(vb, j, |
| q->format.plane_fmt[j].sizeimage); |
| return; |
| } |
| |
| dev_dbg(dev, "entry %i was full!\n", next); |
| next = (next + 1) % CIO2_MAX_BUFFERS; |
| } |
| |
| local_irq_restore(flags); |
| dev_err(dev, "error: all cio2 entries were full!\n"); |
| atomic_dec(&q->bufs_queued); |
| vb2_buffer_done(vb, VB2_BUF_STATE_ERROR); |
| } |
| |
| /* Called when each buffer is freed */ |
| static void cio2_vb2_buf_cleanup(struct vb2_buffer *vb) |
| { |
| struct cio2_device *cio2 = vb2_get_drv_priv(vb->vb2_queue); |
| struct device *dev = &cio2->pci_dev->dev; |
| struct cio2_buffer *b = to_cio2_buffer(vb); |
| unsigned int i; |
| |
| /* Free LOP table */ |
| for (i = 0; i < CIO2_MAX_LOPS; i++) { |
| if (b->lop[i]) |
| dma_free_coherent(dev, PAGE_SIZE, |
| b->lop[i], b->lop_bus_addr[i]); |
| } |
| } |
| |
| static int cio2_vb2_start_streaming(struct vb2_queue *vq, unsigned int count) |
| { |
| struct cio2_queue *q = vb2q_to_cio2_queue(vq); |
| struct cio2_device *cio2 = vb2_get_drv_priv(vq); |
| struct device *dev = &cio2->pci_dev->dev; |
| int r; |
| |
| cio2->cur_queue = q; |
| atomic_set(&q->frame_sequence, 0); |
| |
| r = pm_runtime_resume_and_get(dev); |
| if (r < 0) { |
| dev_info(dev, "failed to set power %d\n", r); |
| return r; |
| } |
| |
| r = video_device_pipeline_start(&q->vdev, &q->pipe); |
| if (r) |
| goto fail_pipeline; |
| |
| r = cio2_hw_init(cio2, q); |
| if (r) |
| goto fail_hw; |
| |
| /* Start streaming on sensor */ |
| r = v4l2_subdev_call(q->sensor, video, s_stream, 1); |
| if (r) |
| goto fail_csi2_subdev; |
| |
| cio2->streaming = true; |
| |
| return 0; |
| |
| fail_csi2_subdev: |
| cio2_hw_exit(cio2, q); |
| fail_hw: |
| video_device_pipeline_stop(&q->vdev); |
| fail_pipeline: |
| dev_dbg(dev, "failed to start streaming (%d)\n", r); |
| cio2_vb2_return_all_buffers(q, VB2_BUF_STATE_QUEUED); |
| pm_runtime_put(dev); |
| |
| return r; |
| } |
| |
| static void cio2_vb2_stop_streaming(struct vb2_queue *vq) |
| { |
| struct cio2_queue *q = vb2q_to_cio2_queue(vq); |
| struct cio2_device *cio2 = vb2_get_drv_priv(vq); |
| struct device *dev = &cio2->pci_dev->dev; |
| |
| if (v4l2_subdev_call(q->sensor, video, s_stream, 0)) |
| dev_err(dev, "failed to stop sensor streaming\n"); |
| |
| cio2_hw_exit(cio2, q); |
| synchronize_irq(cio2->pci_dev->irq); |
| cio2_vb2_return_all_buffers(q, VB2_BUF_STATE_ERROR); |
| video_device_pipeline_stop(&q->vdev); |
| pm_runtime_put(dev); |
| cio2->streaming = false; |
| } |
| |
| static const struct vb2_ops cio2_vb2_ops = { |
| .buf_init = cio2_vb2_buf_init, |
| .buf_queue = cio2_vb2_buf_queue, |
| .buf_cleanup = cio2_vb2_buf_cleanup, |
| .queue_setup = cio2_vb2_queue_setup, |
| .start_streaming = cio2_vb2_start_streaming, |
| .stop_streaming = cio2_vb2_stop_streaming, |
| .wait_prepare = vb2_ops_wait_prepare, |
| .wait_finish = vb2_ops_wait_finish, |
| }; |
| |
| /**************** V4L2 interface ****************/ |
| |
| static int cio2_v4l2_querycap(struct file *file, void *fh, |
| struct v4l2_capability *cap) |
| { |
| strscpy(cap->driver, CIO2_NAME, sizeof(cap->driver)); |
| strscpy(cap->card, CIO2_DEVICE_NAME, sizeof(cap->card)); |
| |
| return 0; |
| } |
| |
| static int cio2_v4l2_enum_fmt(struct file *file, void *fh, |
| struct v4l2_fmtdesc *f) |
| { |
| if (f->index >= ARRAY_SIZE(formats)) |
| return -EINVAL; |
| |
| f->pixelformat = formats[f->index].fourcc; |
| |
| return 0; |
| } |
| |
| /* The format is validated in cio2_video_link_validate() */ |
| static int cio2_v4l2_g_fmt(struct file *file, void *fh, struct v4l2_format *f) |
| { |
| struct cio2_queue *q = file_to_cio2_queue(file); |
| |
| f->fmt.pix_mp = q->format; |
| |
| return 0; |
| } |
| |
| static int cio2_v4l2_try_fmt(struct file *file, void *fh, struct v4l2_format *f) |
| { |
| const struct ipu3_cio2_fmt *fmt; |
| struct v4l2_pix_format_mplane *mpix = &f->fmt.pix_mp; |
| |
| fmt = cio2_find_format(&mpix->pixelformat, NULL); |
| if (!fmt) |
| fmt = &formats[0]; |
| |
| /* Only supports up to 4224x3136 */ |
| if (mpix->width > CIO2_IMAGE_MAX_WIDTH) |
| mpix->width = CIO2_IMAGE_MAX_WIDTH; |
| if (mpix->height > CIO2_IMAGE_MAX_HEIGHT) |
| mpix->height = CIO2_IMAGE_MAX_HEIGHT; |
| |
| mpix->num_planes = 1; |
| mpix->pixelformat = fmt->fourcc; |
| mpix->colorspace = V4L2_COLORSPACE_RAW; |
| mpix->field = V4L2_FIELD_NONE; |
| mpix->plane_fmt[0].bytesperline = cio2_bytesperline(mpix->width); |
| mpix->plane_fmt[0].sizeimage = mpix->plane_fmt[0].bytesperline * |
| mpix->height; |
| |
| /* use default */ |
| mpix->ycbcr_enc = V4L2_YCBCR_ENC_DEFAULT; |
| mpix->quantization = V4L2_QUANTIZATION_DEFAULT; |
| mpix->xfer_func = V4L2_XFER_FUNC_DEFAULT; |
| |
| return 0; |
| } |
| |
| static int cio2_v4l2_s_fmt(struct file *file, void *fh, struct v4l2_format *f) |
| { |
| struct cio2_queue *q = file_to_cio2_queue(file); |
| |
| cio2_v4l2_try_fmt(file, fh, f); |
| q->format = f->fmt.pix_mp; |
| |
| return 0; |
| } |
| |
| static int |
| cio2_video_enum_input(struct file *file, void *fh, struct v4l2_input *input) |
| { |
| if (input->index > 0) |
| return -EINVAL; |
| |
| strscpy(input->name, "camera", sizeof(input->name)); |
| input->type = V4L2_INPUT_TYPE_CAMERA; |
| |
| return 0; |
| } |
| |
| static int |
| cio2_video_g_input(struct file *file, void *fh, unsigned int *input) |
| { |
| *input = 0; |
| |
| return 0; |
| } |
| |
| static int |
| cio2_video_s_input(struct file *file, void *fh, unsigned int input) |
| { |
| return input == 0 ? 0 : -EINVAL; |
| } |
| |
| static const struct v4l2_file_operations cio2_v4l2_fops = { |
| .owner = THIS_MODULE, |
| .unlocked_ioctl = video_ioctl2, |
| .open = v4l2_fh_open, |
| .release = vb2_fop_release, |
| .poll = vb2_fop_poll, |
| .mmap = vb2_fop_mmap, |
| }; |
| |
| static const struct v4l2_ioctl_ops cio2_v4l2_ioctl_ops = { |
| .vidioc_querycap = cio2_v4l2_querycap, |
| .vidioc_enum_fmt_vid_cap = cio2_v4l2_enum_fmt, |
| .vidioc_g_fmt_vid_cap_mplane = cio2_v4l2_g_fmt, |
| .vidioc_s_fmt_vid_cap_mplane = cio2_v4l2_s_fmt, |
| .vidioc_try_fmt_vid_cap_mplane = cio2_v4l2_try_fmt, |
| .vidioc_reqbufs = vb2_ioctl_reqbufs, |
| .vidioc_create_bufs = vb2_ioctl_create_bufs, |
| .vidioc_prepare_buf = vb2_ioctl_prepare_buf, |
| .vidioc_querybuf = vb2_ioctl_querybuf, |
| .vidioc_qbuf = vb2_ioctl_qbuf, |
| .vidioc_dqbuf = vb2_ioctl_dqbuf, |
| .vidioc_streamon = vb2_ioctl_streamon, |
| .vidioc_streamoff = vb2_ioctl_streamoff, |
| .vidioc_expbuf = vb2_ioctl_expbuf, |
| .vidioc_enum_input = cio2_video_enum_input, |
| .vidioc_g_input = cio2_video_g_input, |
| .vidioc_s_input = cio2_video_s_input, |
| }; |
| |
| static int cio2_subdev_subscribe_event(struct v4l2_subdev *sd, |
| struct v4l2_fh *fh, |
| struct v4l2_event_subscription *sub) |
| { |
| if (sub->type != V4L2_EVENT_FRAME_SYNC) |
| return -EINVAL; |
| |
| /* Line number. For now only zero accepted. */ |
| if (sub->id != 0) |
| return -EINVAL; |
| |
| return v4l2_event_subscribe(fh, sub, 0, NULL); |
| } |
| |
| static int cio2_subdev_open(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh) |
| { |
| struct v4l2_mbus_framefmt *format; |
| const struct v4l2_mbus_framefmt fmt_default = { |
| .width = 1936, |
| .height = 1096, |
| .code = formats[0].mbus_code, |
| .field = V4L2_FIELD_NONE, |
| .colorspace = V4L2_COLORSPACE_RAW, |
| .ycbcr_enc = V4L2_YCBCR_ENC_DEFAULT, |
| .quantization = V4L2_QUANTIZATION_DEFAULT, |
| .xfer_func = V4L2_XFER_FUNC_DEFAULT, |
| }; |
| |
| /* Initialize try_fmt */ |
| format = v4l2_subdev_state_get_format(fh->state, CIO2_PAD_SINK); |
| *format = fmt_default; |
| |
| /* same as sink */ |
| format = v4l2_subdev_state_get_format(fh->state, CIO2_PAD_SOURCE); |
| *format = fmt_default; |
| |
| return 0; |
| } |
| |
| static int cio2_subdev_get_fmt(struct v4l2_subdev *sd, |
| struct v4l2_subdev_state *sd_state, |
| struct v4l2_subdev_format *fmt) |
| { |
| struct cio2_queue *q = container_of(sd, struct cio2_queue, subdev); |
| |
| mutex_lock(&q->subdev_lock); |
| |
| if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) |
| fmt->format = *v4l2_subdev_state_get_format(sd_state, |
| fmt->pad); |
| else |
| fmt->format = q->subdev_fmt; |
| |
| mutex_unlock(&q->subdev_lock); |
| |
| return 0; |
| } |
| |
| static int cio2_subdev_set_fmt(struct v4l2_subdev *sd, |
| struct v4l2_subdev_state *sd_state, |
| struct v4l2_subdev_format *fmt) |
| { |
| struct cio2_queue *q = container_of(sd, struct cio2_queue, subdev); |
| struct v4l2_mbus_framefmt *mbus; |
| u32 mbus_code = fmt->format.code; |
| unsigned int i; |
| |
| /* |
| * Only allow setting sink pad format; |
| * source always propagates from sink |
| */ |
| if (fmt->pad == CIO2_PAD_SOURCE) |
| return cio2_subdev_get_fmt(sd, sd_state, fmt); |
| |
| if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) |
| mbus = v4l2_subdev_state_get_format(sd_state, fmt->pad); |
| else |
| mbus = &q->subdev_fmt; |
| |
| fmt->format.code = formats[0].mbus_code; |
| |
| for (i = 0; i < ARRAY_SIZE(formats); i++) { |
| if (formats[i].mbus_code == mbus_code) { |
| fmt->format.code = mbus_code; |
| break; |
| } |
| } |
| |
| fmt->format.width = min(fmt->format.width, CIO2_IMAGE_MAX_WIDTH); |
| fmt->format.height = min(fmt->format.height, CIO2_IMAGE_MAX_HEIGHT); |
| fmt->format.field = V4L2_FIELD_NONE; |
| |
| mutex_lock(&q->subdev_lock); |
| *mbus = fmt->format; |
| mutex_unlock(&q->subdev_lock); |
| |
| return 0; |
| } |
| |
| static int cio2_subdev_enum_mbus_code(struct v4l2_subdev *sd, |
| struct v4l2_subdev_state *sd_state, |
| struct v4l2_subdev_mbus_code_enum *code) |
| { |
| if (code->index >= ARRAY_SIZE(formats)) |
| return -EINVAL; |
| |
| code->code = formats[code->index].mbus_code; |
| return 0; |
| } |
| |
| static int cio2_subdev_link_validate_get_format(struct media_pad *pad, |
| struct v4l2_subdev_format *fmt) |
| { |
| if (is_media_entity_v4l2_subdev(pad->entity)) { |
| struct v4l2_subdev *sd = |
| media_entity_to_v4l2_subdev(pad->entity); |
| |
| memset(fmt, 0, sizeof(*fmt)); |
| fmt->which = V4L2_SUBDEV_FORMAT_ACTIVE; |
| fmt->pad = pad->index; |
| return v4l2_subdev_call(sd, pad, get_fmt, NULL, fmt); |
| } |
| |
| return -EINVAL; |
| } |
| |
| static int cio2_video_link_validate(struct media_link *link) |
| { |
| struct media_entity *entity = link->sink->entity; |
| struct video_device *vd = media_entity_to_video_device(entity); |
| struct cio2_queue *q = container_of(vd, struct cio2_queue, vdev); |
| struct cio2_device *cio2 = video_get_drvdata(vd); |
| struct device *dev = &cio2->pci_dev->dev; |
| struct v4l2_subdev_format source_fmt; |
| int ret; |
| |
| if (!media_pad_remote_pad_first(entity->pads)) { |
| dev_info(dev, "video node %s pad not connected\n", vd->name); |
| return -ENOTCONN; |
| } |
| |
| ret = cio2_subdev_link_validate_get_format(link->source, &source_fmt); |
| if (ret < 0) |
| return 0; |
| |
| if (source_fmt.format.width != q->format.width || |
| source_fmt.format.height != q->format.height) { |
| dev_err(dev, "Wrong width or height %ux%u (%ux%u expected)\n", |
| q->format.width, q->format.height, |
| source_fmt.format.width, source_fmt.format.height); |
| return -EINVAL; |
| } |
| |
| if (!cio2_find_format(&q->format.pixelformat, &source_fmt.format.code)) |
| return -EINVAL; |
| |
| return 0; |
| } |
| |
| static const struct v4l2_subdev_core_ops cio2_subdev_core_ops = { |
| .subscribe_event = cio2_subdev_subscribe_event, |
| .unsubscribe_event = v4l2_event_subdev_unsubscribe, |
| }; |
| |
| static const struct v4l2_subdev_internal_ops cio2_subdev_internal_ops = { |
| .open = cio2_subdev_open, |
| }; |
| |
| static const struct v4l2_subdev_pad_ops cio2_subdev_pad_ops = { |
| .link_validate = v4l2_subdev_link_validate_default, |
| .get_fmt = cio2_subdev_get_fmt, |
| .set_fmt = cio2_subdev_set_fmt, |
| .enum_mbus_code = cio2_subdev_enum_mbus_code, |
| }; |
| |
| static const struct v4l2_subdev_ops cio2_subdev_ops = { |
| .core = &cio2_subdev_core_ops, |
| .pad = &cio2_subdev_pad_ops, |
| }; |
| |
| /******* V4L2 sub-device asynchronous registration callbacks***********/ |
| |
| struct sensor_async_subdev { |
| struct v4l2_async_connection asd; |
| struct csi2_bus_info csi2; |
| }; |
| |
| #define to_sensor_asd(__asd) \ |
| container_of_const(__asd, struct sensor_async_subdev, asd) |
| |
| /* The .bound() notifier callback when a match is found */ |
| static int cio2_notifier_bound(struct v4l2_async_notifier *notifier, |
| struct v4l2_subdev *sd, |
| struct v4l2_async_connection *asd) |
| { |
| struct cio2_device *cio2 = to_cio2_device(notifier); |
| struct sensor_async_subdev *s_asd = to_sensor_asd(asd); |
| struct cio2_queue *q; |
| int ret; |
| |
| if (cio2->queue[s_asd->csi2.port].sensor) |
| return -EBUSY; |
| |
| ret = ipu_bridge_instantiate_vcm(sd->dev); |
| if (ret) |
| return ret; |
| |
| q = &cio2->queue[s_asd->csi2.port]; |
| |
| q->csi2 = s_asd->csi2; |
| q->sensor = sd; |
| q->csi_rx_base = cio2->base + CIO2_REG_PIPE_BASE(q->csi2.port); |
| |
| return 0; |
| } |
| |
| /* The .unbind callback */ |
| static void cio2_notifier_unbind(struct v4l2_async_notifier *notifier, |
| struct v4l2_subdev *sd, |
| struct v4l2_async_connection *asd) |
| { |
| struct cio2_device *cio2 = to_cio2_device(notifier); |
| struct sensor_async_subdev *s_asd = to_sensor_asd(asd); |
| |
| cio2->queue[s_asd->csi2.port].sensor = NULL; |
| } |
| |
| /* .complete() is called after all subdevices have been located */ |
| static int cio2_notifier_complete(struct v4l2_async_notifier *notifier) |
| { |
| struct cio2_device *cio2 = to_cio2_device(notifier); |
| struct sensor_async_subdev *s_asd; |
| struct v4l2_async_connection *asd; |
| struct cio2_queue *q; |
| int ret; |
| |
| list_for_each_entry(asd, &cio2->notifier.done_list, asc_entry) { |
| s_asd = to_sensor_asd(asd); |
| q = &cio2->queue[s_asd->csi2.port]; |
| |
| ret = v4l2_create_fwnode_links_to_pad(asd->sd, |
| &q->subdev_pads[CIO2_PAD_SINK], 0); |
| if (ret) |
| return ret; |
| } |
| |
| return v4l2_device_register_subdev_nodes(&cio2->v4l2_dev); |
| } |
| |
| static const struct v4l2_async_notifier_operations cio2_async_ops = { |
| .bound = cio2_notifier_bound, |
| .unbind = cio2_notifier_unbind, |
| .complete = cio2_notifier_complete, |
| }; |
| |
| static int cio2_parse_firmware(struct cio2_device *cio2) |
| { |
| struct device *dev = &cio2->pci_dev->dev; |
| unsigned int i; |
| int ret; |
| |
| for (i = 0; i < CIO2_NUM_PORTS; i++) { |
| struct v4l2_fwnode_endpoint vep = { |
| .bus_type = V4L2_MBUS_CSI2_DPHY |
| }; |
| struct sensor_async_subdev *s_asd; |
| struct fwnode_handle *ep; |
| |
| ep = fwnode_graph_get_endpoint_by_id(dev_fwnode(dev), i, 0, |
| FWNODE_GRAPH_ENDPOINT_NEXT); |
| if (!ep) |
| continue; |
| |
| ret = v4l2_fwnode_endpoint_parse(ep, &vep); |
| if (ret) |
| goto err_parse; |
| |
| s_asd = v4l2_async_nf_add_fwnode_remote(&cio2->notifier, ep, |
| struct |
| sensor_async_subdev); |
| if (IS_ERR(s_asd)) { |
| ret = PTR_ERR(s_asd); |
| goto err_parse; |
| } |
| |
| s_asd->csi2.port = vep.base.port; |
| s_asd->csi2.lanes = vep.bus.mipi_csi2.num_data_lanes; |
| |
| fwnode_handle_put(ep); |
| |
| continue; |
| |
| err_parse: |
| fwnode_handle_put(ep); |
| return ret; |
| } |
| |
| /* |
| * Proceed even without sensors connected to allow the device to |
| * suspend. |
| */ |
| cio2->notifier.ops = &cio2_async_ops; |
| ret = v4l2_async_nf_register(&cio2->notifier); |
| if (ret) |
| dev_err(dev, "failed to register async notifier : %d\n", ret); |
| |
| return ret; |
| } |
| |
| /**************** Queue initialization ****************/ |
| static const struct media_entity_operations cio2_media_ops = { |
| .link_validate = v4l2_subdev_link_validate, |
| }; |
| |
| static const struct media_entity_operations cio2_video_entity_ops = { |
| .link_validate = cio2_video_link_validate, |
| }; |
| |
| static int cio2_queue_init(struct cio2_device *cio2, struct cio2_queue *q) |
| { |
| static const u32 default_width = 1936; |
| static const u32 default_height = 1096; |
| const struct ipu3_cio2_fmt dflt_fmt = formats[0]; |
| struct device *dev = &cio2->pci_dev->dev; |
| struct video_device *vdev = &q->vdev; |
| struct vb2_queue *vbq = &q->vbq; |
| struct v4l2_subdev *subdev = &q->subdev; |
| struct v4l2_mbus_framefmt *fmt; |
| int r; |
| |
| /* Initialize miscellaneous variables */ |
| mutex_init(&q->lock); |
| mutex_init(&q->subdev_lock); |
| |
| /* Initialize formats to default values */ |
| fmt = &q->subdev_fmt; |
| fmt->width = default_width; |
| fmt->height = default_height; |
| fmt->code = dflt_fmt.mbus_code; |
| fmt->field = V4L2_FIELD_NONE; |
| |
| q->format.width = default_width; |
| q->format.height = default_height; |
| q->format.pixelformat = dflt_fmt.fourcc; |
| q->format.colorspace = V4L2_COLORSPACE_RAW; |
| q->format.field = V4L2_FIELD_NONE; |
| q->format.num_planes = 1; |
| q->format.plane_fmt[0].bytesperline = |
| cio2_bytesperline(q->format.width); |
| q->format.plane_fmt[0].sizeimage = q->format.plane_fmt[0].bytesperline * |
| q->format.height; |
| |
| /* Initialize fbpt */ |
| r = cio2_fbpt_init(cio2, q); |
| if (r) |
| goto fail_fbpt; |
| |
| /* Initialize media entities */ |
| q->subdev_pads[CIO2_PAD_SINK].flags = MEDIA_PAD_FL_SINK | |
| MEDIA_PAD_FL_MUST_CONNECT; |
| q->subdev_pads[CIO2_PAD_SOURCE].flags = MEDIA_PAD_FL_SOURCE; |
| subdev->entity.ops = &cio2_media_ops; |
| subdev->internal_ops = &cio2_subdev_internal_ops; |
| r = media_entity_pads_init(&subdev->entity, CIO2_PADS, q->subdev_pads); |
| if (r) { |
| dev_err(dev, "failed initialize subdev media entity (%d)\n", r); |
| goto fail_subdev_media_entity; |
| } |
| |
| q->vdev_pad.flags = MEDIA_PAD_FL_SINK | MEDIA_PAD_FL_MUST_CONNECT; |
| vdev->entity.ops = &cio2_video_entity_ops; |
| r = media_entity_pads_init(&vdev->entity, 1, &q->vdev_pad); |
| if (r) { |
| dev_err(dev, "failed initialize videodev media entity (%d)\n", |
| r); |
| goto fail_vdev_media_entity; |
| } |
| |
| /* Initialize subdev */ |
| v4l2_subdev_init(subdev, &cio2_subdev_ops); |
| subdev->flags = V4L2_SUBDEV_FL_HAS_DEVNODE | V4L2_SUBDEV_FL_HAS_EVENTS; |
| subdev->owner = THIS_MODULE; |
| subdev->dev = dev; |
| snprintf(subdev->name, sizeof(subdev->name), |
| CIO2_ENTITY_NAME " %td", q - cio2->queue); |
| subdev->entity.function = MEDIA_ENT_F_VID_IF_BRIDGE; |
| v4l2_set_subdevdata(subdev, cio2); |
| r = v4l2_device_register_subdev(&cio2->v4l2_dev, subdev); |
| if (r) { |
| dev_err(dev, "failed initialize subdev (%d)\n", r); |
| goto fail_subdev; |
| } |
| |
| /* Initialize vbq */ |
| vbq->type = V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE; |
| vbq->io_modes = VB2_USERPTR | VB2_MMAP | VB2_DMABUF; |
| vbq->ops = &cio2_vb2_ops; |
| vbq->mem_ops = &vb2_dma_sg_memops; |
| vbq->buf_struct_size = sizeof(struct cio2_buffer); |
| vbq->timestamp_flags = V4L2_BUF_FLAG_TIMESTAMP_MONOTONIC; |
| vbq->min_queued_buffers = 1; |
| vbq->drv_priv = cio2; |
| vbq->lock = &q->lock; |
| r = vb2_queue_init(vbq); |
| if (r) { |
| dev_err(dev, "failed to initialize videobuf2 queue (%d)\n", r); |
| goto fail_subdev; |
| } |
| |
| /* Initialize vdev */ |
| snprintf(vdev->name, sizeof(vdev->name), |
| "%s %td", CIO2_NAME, q - cio2->queue); |
| vdev->release = video_device_release_empty; |
| vdev->fops = &cio2_v4l2_fops; |
| vdev->ioctl_ops = &cio2_v4l2_ioctl_ops; |
| vdev->lock = &cio2->lock; |
| vdev->v4l2_dev = &cio2->v4l2_dev; |
| vdev->queue = &q->vbq; |
| vdev->device_caps = V4L2_CAP_VIDEO_CAPTURE_MPLANE | V4L2_CAP_STREAMING; |
| video_set_drvdata(vdev, cio2); |
| r = video_register_device(vdev, VFL_TYPE_VIDEO, -1); |
| if (r) { |
| dev_err(dev, "failed to register video device (%d)\n", r); |
| goto fail_vdev; |
| } |
| |
| /* Create link from CIO2 subdev to output node */ |
| r = media_create_pad_link( |
| &subdev->entity, CIO2_PAD_SOURCE, &vdev->entity, 0, |
| MEDIA_LNK_FL_ENABLED | MEDIA_LNK_FL_IMMUTABLE); |
| if (r) |
| goto fail_link; |
| |
| return 0; |
| |
| fail_link: |
| vb2_video_unregister_device(&q->vdev); |
| fail_vdev: |
| v4l2_device_unregister_subdev(subdev); |
| fail_subdev: |
| media_entity_cleanup(&vdev->entity); |
| fail_vdev_media_entity: |
| media_entity_cleanup(&subdev->entity); |
| fail_subdev_media_entity: |
| cio2_fbpt_exit(q, dev); |
| fail_fbpt: |
| mutex_destroy(&q->subdev_lock); |
| mutex_destroy(&q->lock); |
| |
| return r; |
| } |
| |
| static void cio2_queue_exit(struct cio2_device *cio2, struct cio2_queue *q) |
| { |
| vb2_video_unregister_device(&q->vdev); |
| media_entity_cleanup(&q->vdev.entity); |
| v4l2_device_unregister_subdev(&q->subdev); |
| media_entity_cleanup(&q->subdev.entity); |
| cio2_fbpt_exit(q, &cio2->pci_dev->dev); |
| mutex_destroy(&q->subdev_lock); |
| mutex_destroy(&q->lock); |
| } |
| |
| static int cio2_queues_init(struct cio2_device *cio2) |
| { |
| int i, r; |
| |
| for (i = 0; i < CIO2_QUEUES; i++) { |
| r = cio2_queue_init(cio2, &cio2->queue[i]); |
| if (r) |
| break; |
| } |
| |
| if (i == CIO2_QUEUES) |
| return 0; |
| |
| for (i--; i >= 0; i--) |
| cio2_queue_exit(cio2, &cio2->queue[i]); |
| |
| return r; |
| } |
| |
| static void cio2_queues_exit(struct cio2_device *cio2) |
| { |
| unsigned int i; |
| |
| for (i = 0; i < CIO2_QUEUES; i++) |
| cio2_queue_exit(cio2, &cio2->queue[i]); |
| } |
| |
| /**************** PCI interface ****************/ |
| |
| static int cio2_pci_probe(struct pci_dev *pci_dev, |
| const struct pci_device_id *id) |
| { |
| struct device *dev = &pci_dev->dev; |
| struct cio2_device *cio2; |
| int r; |
| |
| /* |
| * On some platforms no connections to sensors are defined in firmware, |
| * if the device has no endpoints then we can try to build those as |
| * software_nodes parsed from SSDB. |
| */ |
| r = ipu_bridge_init(dev, ipu_bridge_parse_ssdb); |
| if (r) |
| return r; |
| |
| cio2 = devm_kzalloc(dev, sizeof(*cio2), GFP_KERNEL); |
| if (!cio2) |
| return -ENOMEM; |
| cio2->pci_dev = pci_dev; |
| |
| r = pcim_enable_device(pci_dev); |
| if (r) { |
| dev_err(dev, "failed to enable device (%d)\n", r); |
| return r; |
| } |
| |
| dev_info(dev, "device 0x%x (rev: 0x%x)\n", |
| pci_dev->device, pci_dev->revision); |
| |
| r = pcim_iomap_regions(pci_dev, 1 << CIO2_PCI_BAR, pci_name(pci_dev)); |
| if (r) { |
| dev_err(dev, "failed to remap I/O memory (%d)\n", r); |
| return -ENODEV; |
| } |
| |
| cio2->base = pcim_iomap_table(pci_dev)[CIO2_PCI_BAR]; |
| |
| pci_set_drvdata(pci_dev, cio2); |
| |
| pci_set_master(pci_dev); |
| |
| r = dma_set_mask(&pci_dev->dev, CIO2_DMA_MASK); |
| if (r) { |
| dev_err(dev, "failed to set DMA mask (%d)\n", r); |
| return -ENODEV; |
| } |
| |
| r = pci_enable_msi(pci_dev); |
| if (r) { |
| dev_err(dev, "failed to enable MSI (%d)\n", r); |
| return r; |
| } |
| |
| r = cio2_fbpt_init_dummy(cio2); |
| if (r) |
| return r; |
| |
| mutex_init(&cio2->lock); |
| |
| cio2->media_dev.dev = dev; |
| strscpy(cio2->media_dev.model, CIO2_DEVICE_NAME, |
| sizeof(cio2->media_dev.model)); |
| cio2->media_dev.hw_revision = 0; |
| |
| media_device_init(&cio2->media_dev); |
| r = media_device_register(&cio2->media_dev); |
| if (r < 0) |
| goto fail_mutex_destroy; |
| |
| cio2->v4l2_dev.mdev = &cio2->media_dev; |
| r = v4l2_device_register(dev, &cio2->v4l2_dev); |
| if (r) { |
| dev_err(dev, "failed to register V4L2 device (%d)\n", r); |
| goto fail_media_device_unregister; |
| } |
| |
| r = cio2_queues_init(cio2); |
| if (r) |
| goto fail_v4l2_device_unregister; |
| |
| v4l2_async_nf_init(&cio2->notifier, &cio2->v4l2_dev); |
| |
| r = devm_request_irq(dev, pci_dev->irq, cio2_irq, IRQF_SHARED, |
| CIO2_NAME, cio2); |
| if (r) { |
| dev_err(dev, "failed to request IRQ (%d)\n", r); |
| goto fail_clean_notifier; |
| } |
| |
| /* Register notifier for subdevices we care */ |
| r = cio2_parse_firmware(cio2); |
| if (r) |
| goto fail_clean_notifier; |
| |
| pm_runtime_put_noidle(dev); |
| pm_runtime_allow(dev); |
| |
| return 0; |
| |
| fail_clean_notifier: |
| v4l2_async_nf_unregister(&cio2->notifier); |
| v4l2_async_nf_cleanup(&cio2->notifier); |
| cio2_queues_exit(cio2); |
| fail_v4l2_device_unregister: |
| v4l2_device_unregister(&cio2->v4l2_dev); |
| fail_media_device_unregister: |
| media_device_unregister(&cio2->media_dev); |
| media_device_cleanup(&cio2->media_dev); |
| fail_mutex_destroy: |
| mutex_destroy(&cio2->lock); |
| cio2_fbpt_exit_dummy(cio2); |
| |
| return r; |
| } |
| |
| static void cio2_pci_remove(struct pci_dev *pci_dev) |
| { |
| struct cio2_device *cio2 = pci_get_drvdata(pci_dev); |
| |
| media_device_unregister(&cio2->media_dev); |
| v4l2_async_nf_unregister(&cio2->notifier); |
| v4l2_async_nf_cleanup(&cio2->notifier); |
| cio2_queues_exit(cio2); |
| cio2_fbpt_exit_dummy(cio2); |
| v4l2_device_unregister(&cio2->v4l2_dev); |
| media_device_cleanup(&cio2->media_dev); |
| mutex_destroy(&cio2->lock); |
| |
| pm_runtime_forbid(&pci_dev->dev); |
| pm_runtime_get_noresume(&pci_dev->dev); |
| } |
| |
| static int __maybe_unused cio2_runtime_suspend(struct device *dev) |
| { |
| struct pci_dev *pci_dev = to_pci_dev(dev); |
| struct cio2_device *cio2 = pci_get_drvdata(pci_dev); |
| void __iomem *const base = cio2->base; |
| |
| writel(CIO2_D0I3C_I3, base + CIO2_REG_D0I3C); |
| dev_dbg(dev, "cio2 runtime suspend.\n"); |
| |
| return 0; |
| } |
| |
| static int __maybe_unused cio2_runtime_resume(struct device *dev) |
| { |
| struct pci_dev *pci_dev = to_pci_dev(dev); |
| struct cio2_device *cio2 = pci_get_drvdata(pci_dev); |
| void __iomem *const base = cio2->base; |
| |
| writel(CIO2_D0I3C_RR, base + CIO2_REG_D0I3C); |
| dev_dbg(dev, "cio2 runtime resume.\n"); |
| |
| return 0; |
| } |
| |
| /* |
| * Helper function to advance all the elements of a circular buffer by "start" |
| * positions |
| */ |
| static void arrange(void *ptr, size_t elem_size, size_t elems, size_t start) |
| { |
| struct { |
| size_t begin, end; |
| } arr[2] = { |
| { 0, start - 1 }, |
| { start, elems - 1 }, |
| }; |
| |
| #define CHUNK_SIZE(a) ((a)->end - (a)->begin + 1) |
| |
| /* Loop as long as we have out-of-place entries */ |
| while (CHUNK_SIZE(&arr[0]) && CHUNK_SIZE(&arr[1])) { |
| size_t size0, i; |
| |
| /* |
| * Find the number of entries that can be arranged on this |
| * iteration. |
| */ |
| size0 = min(CHUNK_SIZE(&arr[0]), CHUNK_SIZE(&arr[1])); |
| |
| /* Swap the entries in two parts of the array. */ |
| for (i = 0; i < size0; i++) { |
| u8 *d = ptr + elem_size * (arr[1].begin + i); |
| u8 *s = ptr + elem_size * (arr[0].begin + i); |
| size_t j; |
| |
| for (j = 0; j < elem_size; j++) |
| swap(d[j], s[j]); |
| } |
| |
| if (CHUNK_SIZE(&arr[0]) > CHUNK_SIZE(&arr[1])) { |
| /* The end of the first array remains unarranged. */ |
| arr[0].begin += size0; |
| } else { |
| /* |
| * The first array is fully arranged so we proceed |
| * handling the next one. |
| */ |
| arr[0].begin = arr[1].begin; |
| arr[0].end = arr[1].begin + size0 - 1; |
| arr[1].begin += size0; |
| } |
| } |
| } |
| |
| static void cio2_fbpt_rearrange(struct cio2_device *cio2, struct cio2_queue *q) |
| { |
| unsigned int i, j; |
| |
| for (i = 0, j = q->bufs_first; i < CIO2_MAX_BUFFERS; |
| i++, j = (j + 1) % CIO2_MAX_BUFFERS) |
| if (q->bufs[j]) |
| break; |
| |
| if (i == CIO2_MAX_BUFFERS) |
| return; |
| |
| if (j) { |
| arrange(q->fbpt, sizeof(struct cio2_fbpt_entry) * CIO2_MAX_LOPS, |
| CIO2_MAX_BUFFERS, j); |
| arrange(q->bufs, sizeof(struct cio2_buffer *), |
| CIO2_MAX_BUFFERS, j); |
| } |
| |
| /* |
| * DMA clears the valid bit when accessing the buffer. |
| * When stopping stream in suspend callback, some of the buffers |
| * may be in invalid state. After resume, when DMA meets the invalid |
| * buffer, it will halt and stop receiving new data. |
| * To avoid DMA halting, set the valid bit for all buffers in FBPT. |
| */ |
| for (i = 0; i < CIO2_MAX_BUFFERS; i++) |
| cio2_fbpt_entry_enable(cio2, q->fbpt + i * CIO2_MAX_LOPS); |
| } |
| |
| static int __maybe_unused cio2_suspend(struct device *dev) |
| { |
| struct pci_dev *pci_dev = to_pci_dev(dev); |
| struct cio2_device *cio2 = pci_get_drvdata(pci_dev); |
| struct cio2_queue *q = cio2->cur_queue; |
| int r; |
| |
| dev_dbg(dev, "cio2 suspend\n"); |
| if (!cio2->streaming) |
| return 0; |
| |
| /* Stop stream */ |
| r = v4l2_subdev_call(q->sensor, video, s_stream, 0); |
| if (r) { |
| dev_err(dev, "failed to stop sensor streaming\n"); |
| return r; |
| } |
| |
| cio2_hw_exit(cio2, q); |
| synchronize_irq(pci_dev->irq); |
| |
| pm_runtime_force_suspend(dev); |
| |
| /* |
| * Upon resume, hw starts to process the fbpt entries from beginning, |
| * so relocate the queued buffs to the fbpt head before suspend. |
| */ |
| cio2_fbpt_rearrange(cio2, q); |
| q->bufs_first = 0; |
| q->bufs_next = 0; |
| |
| return 0; |
| } |
| |
| static int __maybe_unused cio2_resume(struct device *dev) |
| { |
| struct cio2_device *cio2 = dev_get_drvdata(dev); |
| struct cio2_queue *q = cio2->cur_queue; |
| int r; |
| |
| dev_dbg(dev, "cio2 resume\n"); |
| if (!cio2->streaming) |
| return 0; |
| /* Start stream */ |
| r = pm_runtime_force_resume(dev); |
| if (r < 0) { |
| dev_err(dev, "failed to set power %d\n", r); |
| return r; |
| } |
| |
| r = cio2_hw_init(cio2, q); |
| if (r) { |
| dev_err(dev, "fail to init cio2 hw\n"); |
| return r; |
| } |
| |
| r = v4l2_subdev_call(q->sensor, video, s_stream, 1); |
| if (r) { |
| dev_err(dev, "fail to start sensor streaming\n"); |
| cio2_hw_exit(cio2, q); |
| } |
| |
| return r; |
| } |
| |
| static const struct dev_pm_ops cio2_pm_ops = { |
| SET_RUNTIME_PM_OPS(&cio2_runtime_suspend, &cio2_runtime_resume, NULL) |
| SET_SYSTEM_SLEEP_PM_OPS(&cio2_suspend, &cio2_resume) |
| }; |
| |
| static const struct pci_device_id cio2_pci_id_table[] = { |
| { PCI_DEVICE(PCI_VENDOR_ID_INTEL, CIO2_PCI_ID) }, |
| { } |
| }; |
| |
| MODULE_DEVICE_TABLE(pci, cio2_pci_id_table); |
| |
| static struct pci_driver cio2_pci_driver = { |
| .name = CIO2_NAME, |
| .id_table = cio2_pci_id_table, |
| .probe = cio2_pci_probe, |
| .remove = cio2_pci_remove, |
| .driver = { |
| .pm = &cio2_pm_ops, |
| }, |
| }; |
| |
| module_pci_driver(cio2_pci_driver); |
| |
| MODULE_AUTHOR("Tuukka Toivonen"); |
| MODULE_AUTHOR("Tianshu Qiu <tian.shu.qiu@intel.com>"); |
| MODULE_AUTHOR("Jian Xu Zheng"); |
| MODULE_AUTHOR("Yuning Pu"); |
| MODULE_AUTHOR("Yong Zhi <yong.zhi@intel.com>"); |
| MODULE_LICENSE("GPL v2"); |
| MODULE_DESCRIPTION("IPU3 CIO2 driver"); |
| MODULE_IMPORT_NS(INTEL_IPU_BRIDGE); |