blob: 2802ddbb83ac78776101bc6dffe257cfb96330cb [file] [log] [blame]
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* Copyright (c) 2019 BayLibre, SAS
* Author: Neil Armstrong <narmstrong@baylibre.com>
* Copyright (c) 2019 Christian Hewitt <christianshewitt@gmail.com>
*/
/dts-v1/;
#include "meson-g12b.dtsi"
#include "meson-g12b-s922x.dtsi"
#include <dt-bindings/input/input.h>
#include <dt-bindings/gpio/meson-g12a-gpio.h>
/ {
aliases {
serial0 = &uart_AO;
ethernet0 = &ethmac;
};
chosen {
stdout-path = "serial0:115200n8";
};
memory@0 {
device_type = "memory";
reg = <0x0 0x0 0x0 0x40000000>;
};
emmc_pwrseq: emmc-pwrseq {
compatible = "mmc-pwrseq-emmc";
reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
};
sdio_pwrseq: sdio-pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
clocks = <&wifi32k>;
clock-names = "ext_clock";
};
flash_1v8: regulator-flash_1v8 {
compatible = "regulator-fixed";
regulator-name = "FLASH_1V8";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
vin-supply = <&vcc_3v3>;
regulator-always-on;
};
main_12v: regulator-main_12v {
compatible = "regulator-fixed";
regulator-name = "12V";
regulator-min-microvolt = <12000000>;
regulator-max-microvolt = <12000000>;
regulator-always-on;
};
vcc_5v: regulator-vcc_5v {
compatible = "regulator-fixed";
regulator-name = "VCC_5V";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
vin-supply = <&main_12v>;
gpio = <&gpio GPIOH_8 GPIO_OPEN_DRAIN>;
enable-active-high;
};
vcc_1v8: regulator-vcc_1v8 {
compatible = "regulator-fixed";
regulator-name = "VCC_1V8";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
vin-supply = <&vcc_3v3>;
regulator-always-on;
};
vcc_3v3: regulator-vcc_3v3 {
compatible = "regulator-fixed";
regulator-name = "VCC_3V3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
vin-supply = <&vddao_3v3>;
regulator-always-on;
/* FIXME: actually controlled by VDDCPU_B_EN */
};
vddcpu_a: regulator-vddcpu-a {
/*
* MP1653 Regulator.
*/
compatible = "pwm-regulator";
regulator-name = "VDDCPU_A";
regulator-min-microvolt = <721000>;
regulator-max-microvolt = <1022000>;
vin-supply = <&main_12v>;
pwms = <&pwm_ab 0 1250 0>;
pwm-dutycycle-range = <100 0>;
regulator-boot-on;
regulator-always-on;
};
vddcpu_b: regulator-vddcpu-b {
/*
* MP1652 Regulator.
*/
compatible = "pwm-regulator";
regulator-name = "VDDCPU_B";
regulator-min-microvolt = <721000>;
regulator-max-microvolt = <1022000>;
vin-supply = <&main_12v>;
pwms = <&pwm_AO_cd 1 1250 0>;
pwm-dutycycle-range = <100 0>;
regulator-boot-on;
regulator-always-on;
};
usb1_pow: regulator-usb1-pow {
compatible = "regulator-fixed";
regulator-name = "USB1_POW";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
vin-supply = <&vcc_5v>;
/* connected to SY6280A Power Switch */
gpio = <&gpio GPIOA_8 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
usb_pwr_en: regulator-usb-pwr-en {
compatible = "regulator-fixed";
regulator-name = "USB_PWR_EN";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
vin-supply = <&vcc_5v>;
/* Connected to USB3 Type-A Port power enable */
gpio = <&gpio GPIOAO_7 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
vddao_1v8: regulator-vddao-1v8 {
compatible = "regulator-fixed";
regulator-name = "VDDAO_1V8";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
vin-supply = <&vddao_3v3>;
regulator-always-on;
};
vddao_3v3: regulator-vddao-3v3 {
compatible = "regulator-fixed";
regulator-name = "VDDAO_3V3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
vin-supply = <&main_12v>;
regulator-always-on;
};
cvbs-connector {
compatible = "composite-video-connector";
port {
cvbs_connector_in: endpoint {
remote-endpoint = <&cvbs_vdac_out>;
};
};
};
hdmi-connector {
compatible = "hdmi-connector";
type = "a";
port {
hdmi_connector_in: endpoint {
remote-endpoint = <&hdmi_tx_tmds_out>;
};
};
};
wifi32k: wifi32k {
compatible = "pwm-clock";
#clock-cells = <0>;
clock-frequency = <32768>;
pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
};
};
&cec_AO {
pinctrl-0 = <&cec_ao_a_h_pins>;
pinctrl-names = "default";
status = "disabled";
hdmi-phandle = <&hdmi_tx>;
};
&cecb_AO {
pinctrl-0 = <&cec_ao_b_h_pins>;
pinctrl-names = "default";
status = "okay";
hdmi-phandle = <&hdmi_tx>;
};
&cpu0 {
cpu-supply = <&vddcpu_b>;
operating-points-v2 = <&cpu_opp_table_0>;
clocks = <&clkc CLKID_CPU_CLK>;
clock-latency = <50000>;
};
&cpu1 {
cpu-supply = <&vddcpu_b>;
operating-points-v2 = <&cpu_opp_table_0>;
clocks = <&clkc CLKID_CPU_CLK>;
clock-latency = <50000>;
};
&cpu100 {
cpu-supply = <&vddcpu_a>;
operating-points-v2 = <&cpub_opp_table_1>;
clocks = <&clkc CLKID_CPUB_CLK>;
clock-latency = <50000>;
};
&cpu101 {
cpu-supply = <&vddcpu_a>;
operating-points-v2 = <&cpub_opp_table_1>;
clocks = <&clkc CLKID_CPUB_CLK>;
clock-latency = <50000>;
};
&cpu102 {
cpu-supply = <&vddcpu_a>;
operating-points-v2 = <&cpub_opp_table_1>;
clocks = <&clkc CLKID_CPUB_CLK>;
clock-latency = <50000>;
};
&cpu103 {
cpu-supply = <&vddcpu_a>;
operating-points-v2 = <&cpub_opp_table_1>;
clocks = <&clkc CLKID_CPUB_CLK>;
clock-latency = <50000>;
};
&cvbs_vdac_port {
cvbs_vdac_out: endpoint {
remote-endpoint = <&cvbs_connector_in>;
};
};
&ext_mdio {
external_phy: ethernet-phy@0 {
/* Realtek RTL8211F (0x001cc916) */
reg = <0>;
max-speed = <1000>;
reset-assert-us = <10000>;
reset-deassert-us = <30000>;
reset-gpios = <&gpio GPIOZ_15 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
interrupt-parent = <&gpio_intc>;
/* MAC_INTR on GPIOZ_14 */
interrupts = <26 IRQ_TYPE_LEVEL_LOW>;
};
};
&ethmac {
pinctrl-0 = <&eth_pins>, <&eth_rgmii_pins>;
pinctrl-names = "default";
status = "okay";
phy-mode = "rgmii";
phy-handle = <&external_phy>;
amlogic,tx-delay-ns = <2>;
};
&hdmi_tx {
status = "okay";
pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
pinctrl-names = "default";
hdmi-supply = <&vcc_5v>;
};
&hdmi_tx_tmds_port {
hdmi_tx_tmds_out: endpoint {
remote-endpoint = <&hdmi_connector_in>;
};
};
&ir {
status = "okay";
pinctrl-0 = <&remote_input_ao_pins>;
pinctrl-names = "default";
};
&pwm_ab {
pinctrl-0 = <&pwm_a_e_pins>;
pinctrl-names = "default";
clocks = <&xtal>;
clock-names = "clkin0";
status = "okay";
};
&pwm_AO_cd {
pinctrl-0 = <&pwm_ao_d_e_pins>;
pinctrl-names = "default";
clocks = <&xtal>;
clock-names = "clkin1";
status = "okay";
};
&pwm_ef {
pinctrl-0 = <&pwm_e_pins>;
pinctrl-names = "default";
clocks = <&xtal>;
clock-names = "clkin0";
status = "okay";
};
/* SDIO */
&sd_emmc_a {
status = "okay";
pinctrl-0 = <&sdio_pins>;
pinctrl-1 = <&sdio_clk_gate_pins>;
pinctrl-names = "default", "clk-gate";
#address-cells = <1>;
#size-cells = <0>;
bus-width = <4>;
cap-sd-highspeed;
max-frequency = <100000000>;
/* WiFi firmware requires power to be kept while in suspend */
keep-power-in-suspend;
non-removable;
disable-wp;
mmc-pwrseq = <&sdio_pwrseq>;
vmmc-supply = <&vddao_3v3>;
vqmmc-supply = <&vddao_1v8>;
brcmf: wifi@1 {
reg = <1>;
compatible = "brcm,bcm4329-fmac";
};
};
/* SD card */
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_c_pins>;
pinctrl-1 = <&sdcard_clk_gate_c_pins>;
pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
max-frequency = <50000000>;
disable-wp;
cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
vmmc-supply = <&vddao_3v3>;
vqmmc-supply = <&vddao_3v3>;
};
/* eMMC */
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>;
pinctrl-1 = <&emmc_clk_gate_pins>;
pinctrl-names = "default", "clk-gate";
bus-width = <8>;
cap-mmc-highspeed;
max-frequency = <100000000>;
disable-wp;
mmc-pwrseq = <&emmc_pwrseq>;
vmmc-supply = <&vcc_3v3>;
vqmmc-supply = <&flash_1v8>;
};
&uart_A {
status = "okay";
pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
pinctrl-names = "default";
uart-has-rtscts;
bluetooth {
compatible = "brcm,bcm43438-bt";
shutdown-gpios = <&gpio GPIOX_17 GPIO_ACTIVE_HIGH>;
max-speed = <2000000>;
clocks = <&wifi32k>;
clock-names = "lpo";
};
};
&uart_AO {
status = "okay";
pinctrl-0 = <&uart_ao_a_pins>;
pinctrl-names = "default";
};
&usb {
status = "okay";
dr_mode = "host";
vbus-supply = <&usb_pwr_en>;
};
&usb2_phy0 {
phy-supply = <&usb1_pow>;
};
&usb2_phy1 {
phy-supply = <&usb1_pow>;
};