blob: 7f9f9886c3497c15122ba3c3b6788930584aa003 [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0
/*
* dts file for Hisilicon HiKey970 Development Board
*
* Copyright (C) 2016, Hisilicon Ltd.
* Copyright (C) 2018, Linaro Ltd.
*
*/
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include "hi3670.dtsi"
#include "hikey970-pinctrl.dtsi"
/ {
model = "HiKey970";
compatible = "hisilicon,hi3670-hikey970", "hisilicon,hi3670";
aliases {
mshc1 = &dwmmc1;
mshc2 = &dwmmc2;
serial0 = &uart0;
serial1 = &uart1;
serial2 = &uart2;
serial3 = &uart3;
serial4 = &uart4;
serial5 = &uart5;
serial6 = &uart6; /* console UART */
};
chosen {
stdout-path = "serial6:115200n8";
};
memory@0 {
device_type = "memory";
/* expect bootloader to fill in this region */
reg = <0x0 0x0 0x0 0x0>;
};
sd_1v8: regulator-1v8 {
compatible = "regulator-fixed";
regulator-name = "fixed-1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
};
sd_3v3: regulator-3v3 {
compatible = "regulator-fixed";
regulator-name = "fixed-3.3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-boot-on;
regulator-always-on;
};
wlan_en: wlan-en-1-8v {
compatible = "regulator-fixed";
regulator-name = "wlan-en-regulator";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
/* GPIO_051_WIFI_EN */
gpio = <&gpio6 3 0>;
/* WLAN card specific delay */
startup-delay-us = <70000>;
enable-active-high;
};
};
/*
* Legend: proper name = the GPIO line is used as GPIO
* NC = not connected (pin out but not routed from the chip to
* anything the board)
* "[PER]" = pin is muxed for [peripheral] (not GPIO)
* "" = no idea, schematic doesn't say, could be
* unrouted (not connected to any external pin)
* LSEC = Low Speed External Connector
* HSEC = High Speed External Connector
*
* Line names are taken from "hikey970-schematics.pdf" from HiSilicon.
*
* For the lines routed to the external connectors the
* lines are named after the 96Boards CE Specification 1.0,
* Appendix "Expansion Connector Signal Description".
*
* When the 96Board naming of a line and the schematic name of
* the same line are in conflict, the 96Board specification
* takes precedence, which means that the external UART on the
* LSEC is named UART0 while the schematic and SoC names this
* UART2. This is only for the informational lines i.e. "[FOO]",
* the GPIO named lines "GPIO-A" thru "GPIO-L" are the only
* ones actually used for GPIO.
*/
&gpio0 {
/* GPIO_000-GPIO_007 */
gpio-line-names =
"",
"TP901", /* TEST_MODE connected to TP901 */
"",
"GPIO_003_USB_HUB_RESET_N",
"NC",
"[AP_GPS_REF_CLK]",
"[I2C3_SCL]",
"[I2C3_SDA]";
};
&gpio1 {
/* GPIO_008-GPIO_015 */
gpio-line-names =
"[UART0_CTS]", /* LSEC pin 3: GPIO_008_UART2_CTS_N */
"[UART0_RTS]", /* LSEC pin 9: GPIO_009_UART2_RTS_N */
"[UART0_TXD]", /* LSEC pin 5: GPIO_010_UART2_TXD */
"[UART0_RXD]", /* LSEC pin 7: GPIO_011_UART2_RXD */
"[USER_LED5]",
"GPIO-I", /* LSEC pin 31: GPIO_013_CAM0_RST_N */
"[USER_LED3]",
"[USER_LED4]";
};
&gpio2 {
/* GPIO_016-GPIO_023 */
gpio-line-names =
"GPIO-G", /* LSEC pin 29: GPIO_016_LCD_TE0 */
"[CSI0_MCLK]", /* HSEC pin 15: ISP_CCLK0_MCAM */
"[CSI1_MCLK]", /* HSEC pin 17: ISP_CCLK1_SCAM */
"GPIO_019_BT_ACTIVE",
"[I2C2_SCL]", /* HSEC pin 32: ISP_SCL0 */
"[I2C2_SDA]", /* HSEC pin 34: ISP_SDA0 */
"[I2C3_SCL]", /* HSEC pin 36: ISP_SCL1 */
"[I2C3_SDA]"; /* HSEC pin 38: ISP_SDA1 */
};
&gpio3 {
/* GPIO_024-GPIO_031 */
gpio-line-names =
"GPIO_024_WIFI_ACTIVE",
"GPIO_025_PERST_M.2",
"[I2C4_SCL]",
"[I2C4_SDA]",
"NC",
"GPIO-H", /* LSEC pin 30: GPIO_029_LCD_RST_N */
"[USER_LED1]",
"GPIO-L"; /* LSEC pin 34: GPIO_031 */
};
&gpio4 {
/* GPIO_032-GPIO_039 */
gpio-line-names =
"GPIO-K", /* LSEC pin 33: GPIO_032_CAM1_RST_N */
"GPIO_033_PMU1_EN",
"GPIO_034_USBSW_SEL",
/*
* These two pins should be used for SD(IO) data according
* to the 96boards specification but seems to be repurposed
* for UART 0. They are however named according to the spec.
*/
"[SD_DAT1]", /* HSEC pin 3: GPIO_035_UART0_RXD */
"[SD_DAT2]", /* HSEC pin 5: GPIO_036_UART0_TXD */
"[UART1_RXD]", /* LSEC pin 13: DEBUG_UART6_RXD */
"[UART1_TXD]", /* LSEC pin 11: DEBUG_UART6_TXD */
"[SOC_GPS_UART3_CTS_N]"; /* TP2304 */
};
&gpio5 {
/* GPIO_040-GPIO_047 */
gpio-line-names =
"[SOC_GPS_UART3_RTS_N]", /* TP2302 */
"[SOC_GPS_UART3_RXD]", /* TP2303 */
"[SOC_GPS_UART3_TXD]", /* TP2305 */
"[SOC_BT_UART4_CTS_N]",
"[SOC_BT_UART4_RTS_N]",
"[SOC_BT_UART4_RXD]",
"[SOC_BT_UART4_TXD]",
"NC";
};
&gpio6 {
/* GPIO_048-GPIO_055 */
gpio-line-names =
"NC",
"GPIO_049_USER_LED6",
"GPIO_050_CAN_RST",
"GPIO_051_WIFI_EN",
"GPIO-D", /* LSEC pin 26 */
"GPIO-J", /* LSEC pin 32 */
"GPIO_054_BT_EN",
"[GPIO_055_SEL]";
};
&gpio7 {
/* GPIO_056-GPIO_063 */
gpio-line-names =
"[PCIE_PERST_L]", "NC", "NC", "NC", "NC", "NC", "NC", "NC";
};
&gpio8 {
/* GPIO_064-GPIO_071 */
gpio-line-names = "NC", "NC", "NC", "NC", "NC", "NC", "NC", "NC";
};
&gpio9 {
/* GPIO_072-GPIO_079 */
gpio-line-names = "NC", "NC", "NC", "NC", "NC", "NC", "NC", "NC";
};
&gpio10 {
/* GPIO_080-GPIO_087 */
gpio-line-names = "NC", "NC", "NC", "NC", "NC", "NC", "NC", "NC";
};
&gpio11 {
/* GPIO_088-GPIO_095 */
gpio-line-names = "NC", "NC", "NC", "NC", "NC", "NC", "NC", "NC";
};
&gpio12 {
/* GPIO_096-GPIO_103 */
gpio-line-names = "NC", "", "", "", "", "", "", "";
};
&gpio13 {
/* GPIO_104-GPIO_111 */
gpio-line-names = "", "", "", "", "", "", "", "";
};
&gpio14 {
/* GPIO_112-GPIO_119 */
gpio-line-names = "", "", "", "", "", "", "", "";
};
&gpio15 {
/* GPIO_120-GPIO_127 */
gpio-line-names = "", "", "", "", "", "", "", "";
};
&gpio16 {
/* GPIO_128-GPIO_135 */
gpio-line-names =
"[WL_SDIO_CLK]",
"[WL_SDIO_CMD]",
"[WL_SDIO_DATA0]",
"[WL_SDIO_DATA1]",
"[WL_SDIO_DATA2]",
"[WL_SDIO_DATA3]",
"[ETH_ISOLATE]",
"NC";
};
&gpio17 {
/* GPIO_136-GPIO_143 */
gpio-line-names =
"[MINI1CLK_EN]", "NC", "", "", "", "", "", "";
};
&gpio18 {
/* GPIO_144-GPIO_151 */
gpio-line-names =
"[SPI1_SCLK]", /* HSEC pin 9: GPIO_144_SPI3_CLK */
"[SPI1_DIN]", /* HSEC pin 11: GPIO_145_SPI3_DI */
"[SPI1_DOUT]", /* HSEC pin 1: GPIO_146_SPI3_DO */
"[SPI1_CS]", /* HSEC pin 7: GPIO_147_SPI3_CS0_N */
"[POWER_INT_N]",
"[CDMA_GPS_SYNC]",
"GPIO_150_PEX_INTA",
"GPIO_151_CAN_INT";
};
&gpio19 {
/* GPIO_152-GPIO_159 */
gpio-line-names = "", "", "", "", "", "", "", "";
};
&gpio20 {
/* GPIO_160-GPIO_167 */
gpio-line-names =
"[SD_CLK]",
"[SD_CMD]",
"[SD_DATA0]",
"[SD_DATA1]",
"[SD_DATA2]",
"[SD_DATA3]",
"GPIO_166_ETHCLK_EN",
"GPIO_167_USER_LED2";
};
&gpio21 {
/* GPIO_168-GPIO_175 */
gpio-line-names =
"GPIO_168_GPS_EN",
"GPIO-C", /* LSEC pin 25: GPIO_169_USIM1_CLK */
"GPIO-E", /* LSEC pin 27: GPIO_170_USIM1_RST */
"GPIO-B", /* LSEC pin 24: GPIO_171_USIM1_DATA */
"", "", "", "", "";
};
&gpio22 {
/* GPIO_176-GPIO_183 */
gpio-line-names =
"[PMU_PWR_HOLD]",
"GPIO_177_WL_WAKEUP_AP",
"[JTAG_TCK]",
"[JTAG_TMS]",
"[JTAG_TDI]",
"[JTAG_TMS]",
"GPIO_182_FATAL_ERR",
"NC";
};
&gpio23 {
/* GPIO_184-GPIO_191 */
gpio-line-names =
"GPIO_184_JTAG_SEL",
"GPIO-F", /* LSEC pin 28: GPIO_185_LCD_BL_PWM */
"[I2C0_SCL]", /* LSEC pin 15: GPIO_186_I2C0_SCL */
"[I2C0_SDA]", /* LSEC pin 17: GPIO_187_I2C0_SDA */
"[GPIO_188_I2C1_SCL]", /* Actual SoC I2C1_SCL */
"[GPIO_189_I2C1_SDA]", /* Actual SoC I2C1_SDA */
"[I2C1_SCL]", /* LSEC pin 19: GPIO_190_I2C2_SCL */
"[I2C2_SDA]"; /* LSEC pin 21: GPIO_191_I2C2_SDA */
};
&gpio24 {
/* GPIO_192-GPIO_199 */
gpio-line-names =
"[SD_LED]",
"NC",
"[PCM_DI]", /* LSEC pin 22: GPIO_194_I2S0_DI */
"[PCM_DO]", /* LSEC pin 20: GPIO_195_I2S0_DO */
"[PCM_CLK]", /* LSEC pin 18: GPIO_196_I2S0_XCLK */
"[PCM_FS]", /* LSEC pin 16: GPIO_197_I2S0_XFS */
"",
"[I2S2_DO]";
};
&gpio25 {
/* GPIO_200-GPIO_207 */
gpio-line-names =
"[I2S2_XCLK]",
"[I2S2_XFS]",
"GPIO_202_PERST_ETH",
"GPIO_203_PWRON_DET",
"GPIO_204_PMU1_IRQ_N",
"GPIO_205_SD_DET",
"GPIO_206_GPS_MOTION_INT",
"GPIO_207_HDMI_SEL";
};
&gpio26 {
/* GPIO_208-GPIO_215 */
gpio-line-names =
"GPIO-A", /* LSEC pin 23: GPIO_208_WAKEUP_SOC */
"GPIO_209_VBUS_TYPEC",
"NC",
"NC",
"NC",
"[SPI0_SCLK]", /* LSEC pin 8: GPIO_213_SPI2_CLK */
"[SPI0_DIN]", /* LSEC pin 10: GPIO_214_SPI2_DI */
"[SPI0_DOUT]"; /* LSEC pin 14: GPIO_215_SPI2_DO */
};
&gpio27 {
/* GPIO_216-GPIO_223 */
gpio-line-names =
"[SPI0_CS]", /* LSEC pin 12: GPIO_216_SPI2_CS0_N */
"GPIO_217_HDMI_PD",
"GPIO_218_GPS_WAKEUP_AP",
"GPIO_219_M.2CLK_EN",
"GPIO_220_PERST_MINI",
"GPIO_221_CC_INT",
"[PCIE_CLKREQ_L]",
"NC";
};
&gpio28 {
/* GPIO_224-GPIO_231 */
gpio-line-names =
"[PMU0_INT]",
"[SPMI_DATA]",
"[SPMI_CLK]",
"[CAN_SPI_CLK]",
"[CAN_SPI_DI]",
"[CAN_SPI_DO]",
"[CAN_SPI_CS]",
"GPIO_231_HDMI_INT";
};
&dwmmc1 {
bus-width = <0x4>;
sd-uhs-sdr12;
sd-uhs-sdr25;
sd-uhs-sdr50;
sd-uhs-sdr104;
cap-sd-highspeed;
disable-wp;
cd-inverted;
cd-gpios = <&gpio25 5 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&sd_pmx_func
&sd_clk_cfg_func
&sd_cfg_func>;
vmmc-supply = <&sd_3v3>;
vqmmc-supply = <&sd_1v8>;
status = "okay";
};
&dwmmc2 { /* WIFI */
bus-width = <0x4>;
non-removable;
broken-cd;
cap-power-off-card;
pinctrl-names = "default";
pinctrl-0 = <&sdio_pmx_func
&sdio_clk_cfg_func
&sdio_cfg_func>;
/* WL_EN */
vmmc-supply = <&wlan_en>;
status = "okay";
wlcore: wlcore@2 {
compatible = "ti,wl1837";
reg = <2>; /* sdio func num */
/* WL_IRQ, GPIO_177_WL_WAKEUP_AP */
interrupt-parent = <&gpio22>;
interrupts = <1 IRQ_TYPE_EDGE_RISING>;
};
};
&uart0 {
/* On High speed expansion header */
label = "HS-UART0";
status = "okay";
};
&uart2 {
/* On Low speed expansion header */
label = "LS-UART0";
status = "okay";
};
&uart6 {
/* On Low speed expansion header */
label = "LS-UART1";
status = "okay";
};