blob: 5d087be04af8a741057485979f296cb3691e158c [file] [log] [blame]
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* Copyright (c) 2019 Fuzhou Rockchip Electronics Co., Ltd
* Copyright (c) 2019 Vamrs Limited
* Copyright (c) 2019 Amarula Solutions(India)
*/
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/pinctrl/rockchip.h>
#include <dt-bindings/pwm/pwm.h>
/ {
compatible = "vamrs,rk3399pro-vmarc-som", "rockchip,rk3399pro";
vcc3v3_pcie: vcc-pcie-regulator {
compatible = "regulator-fixed";
enable-active-high;
gpio = <&gpio4 RK_PD4 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&pcie_pwr>;
regulator-name = "vcc3v3_pcie";
regulator-always-on;
regulator-boot-on;
vin-supply = <&vcc5v0_sys>;
};
};
&cpu_l0 {
cpu-supply = <&vdd_cpu_l>;
};
&cpu_l1 {
cpu-supply = <&vdd_cpu_l>;
};
&cpu_l2 {
cpu-supply = <&vdd_cpu_l>;
};
&cpu_l3 {
cpu-supply = <&vdd_cpu_l>;
};
&emmc_phy {
status = "okay";
};
&gmac {
assigned-clocks = <&cru SCLK_RMII_SRC>;
phy-supply = <&vcc_lan>;
snps,reset-gpio = <&gpio3 RK_PB7 GPIO_ACTIVE_LOW>;
};
&hdmi {
ddc-i2c-bus = <&i2c3>;
pinctrl-names = "default";
pinctrl-0 = <&hdmi_cec>;
};
&i2c0 {
clock-frequency = <400000>;
i2c-scl-falling-time-ns = <30>;
i2c-scl-rising-time-ns = <180>;
status = "okay";
rk809: pmic@20 {
compatible = "rockchip,rk809";
reg = <0x20>;
interrupt-parent = <&gpio1>;
interrupts = <RK_PC2 IRQ_TYPE_LEVEL_LOW>;
#clock-cells = <1>;
clock-output-names = "rk808-clkout1", "rk808-clkout2";
pinctrl-names = "default";
pinctrl-0 = <&pmic_int_l>;
rockchip,system-power-controller;
wakeup-source;
vcc1-supply = <&vcc5v0_sys>;
vcc2-supply = <&vcc5v0_sys>;
vcc3-supply = <&vcc5v0_sys>;
vcc4-supply = <&vcc5v0_sys>;
vcc5-supply = <&vcc_buck5>;
vcc6-supply = <&vcc_buck5>;
vcc7-supply = <&vcc5v0_sys>;
vcc8-supply = <&vcc3v3_sys>;
vcc9-supply = <&vcc5v0_sys>;
regulators {
vdd_log: DCDC_REG1 {
regulator-name = "vdd_log";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <750000>;
regulator-max-microvolt = <1350000>;
regulator-initial-mode = <0x2>;
regulator-state-mem {
regulator-off-in-suspend;
regulator-suspend-microvolt = <900000>;
};
};
vdd_cpu_l: DCDC_REG2 {
regulator-name = "vdd_cpu_l";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <750000>;
regulator-max-microvolt = <1350000>;
regulator-ramp-delay = <6001>;
regulator-initial-mode = <0x2>;
regulator-state-mem {
regulator-off-in-suspend;
};
};
vcc_ddr: DCDC_REG3 {
regulator-name = "vcc_ddr";
regulator-always-on;
regulator-boot-on;
regulator-initial-mode = <0x2>;
regulator-state-mem {
regulator-on-in-suspend;
};
};
vcc3v3_sys: DCDC_REG4 {
regulator-name = "vcc3v3_sys";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-initial-mode = <0x2>;
regulator-state-mem {
regulator-on-in-suspend;
regulator-suspend-microvolt = <3300000>;
};
};
vcc_buck5: DCDC_REG5 {
regulator-name = "vcc_buck5";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <2200000>;
regulator-max-microvolt = <2200000>;
regulator-state-mem {
regulator-on-in-suspend;
regulator-suspend-microvolt = <2200000>;
};
};
vcca_0v9: LDO_REG1 {
regulator-name = "vcca_0v9";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <900000>;
regulator-max-microvolt = <900000>;
regulator-state-mem {
regulator-on-in-suspend;
regulator-suspend-microvolt = <900000>;
};
};
vcc_1v8: LDO_REG2 {
regulator-name = "vcc_1v8";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-state-mem {
regulator-on-in-suspend;
regulator-suspend-microvolt = <1800000>;
};
};
vcc_0v9: LDO_REG3 {
regulator-name = "vcc_0v9";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <900000>;
regulator-max-microvolt = <900000>;
regulator-state-mem {
regulator-on-in-suspend;
regulator-suspend-microvolt = <900000>;
};
};
vcca_1v8: LDO_REG4 {
regulator-name = "vcca_1v8";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <1850000>;
regulator-max-microvolt = <1850000>;
regulator-state-mem {
regulator-on-in-suspend;
regulator-suspend-microvolt = <1850000>;
};
};
/*
* As per BSP, but schematic not showing any regulator
* pin for LD05.
*/
vdd1v5_dvp: LDO_REG5 {
regulator-name = "vdd1v5_dvp";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <1500000>;
regulator-max-microvolt = <1500000>;
regulator-state-mem {
regulator-off-in-suspend;
};
};
vcc_1v5: LDO_REG6 {
regulator-name = "vcc_1v5";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <1500000>;
regulator-max-microvolt = <1500000>;
regulator-state-mem {
regulator-off-in-suspend;
};
};
vccio_3v0: LDO_REG7 {
regulator-name = "vccio_3v0";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
regulator-state-mem {
regulator-off-in-suspend;
};
};
vccio_sd: LDO_REG8 {
regulator-name = "vccio_sd";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
regulator-state-mem {
regulator-off-in-suspend;
};
};
/*
* As per BSP, but schematic not showing any regulator
* pin for LD09.
*/
vcc_sd: LDO_REG9 {
regulator-name = "vcc_sd";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-state-mem {
regulator-off-in-suspend;
};
};
vcc5v0_usb2: SWITCH_REG1 {
regulator-name = "vcc5v0_usb2";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
regulator-state-mem {
regulator-on-in-suspend;
regulator-suspend-microvolt = <5000000>;
};
};
vccio_3v3: vcc_lan: SWITCH_REG2 {
regulator-name = "vccio_3v3";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-state-mem {
regulator-off-in-suspend;
};
};
};
};
};
&i2c1 {
i2c-scl-falling-time-ns = <30>;
i2c-scl-rising-time-ns = <140>;
status = "okay";
};
&i2c2 {
clock-frequency = <400000>;
status = "okay";
hym8563: hym8563@51 {
compatible = "haoyu,hym8563";
reg = <0x51>;
#clock-cells = <0>;
clock-frequency = <32768>;
clock-output-names = "hym8563";
pinctrl-names = "default";
pinctrl-0 = <&hym8563_int>;
interrupt-parent = <&gpio4>;
interrupts = <RK_PD6 IRQ_TYPE_LEVEL_LOW>;
};
};
&i2c3 {
i2c-scl-rising-time-ns = <450>;
i2c-scl-falling-time-ns = <15>;
status = "okay";
};
&io_domains {
status = "okay";
bt656-supply = <&vcca_1v8>;
gpio1830-supply = <&vccio_3v0>;
sdmmc-supply = <&vccio_sd>;
};
&pcie_phy {
status = "okay";
};
&pcie0 {
ep-gpios = <&gpio0 RK_PB4 GPIO_ACTIVE_HIGH>;
max-link-speed = <2>;
num-lanes = <4>;
pinctrl-0 = <&pcie_clkreqnb_cpm>;
pinctrl-names = "default";
vpcie0v9-supply = <&vcca_0v9>; /* VCC_0V9_S0 */
vpcie1v8-supply = <&vcca_1v8>; /* VCC_1V8_S0 */
vpcie3v3-supply = <&vcc3v3_pcie>;
status = "okay";
};
&pinctrl {
hym8563 {
hym8563_int: hym8563-int {
rockchip,pins = <4 RK_PD6 0 &pcfg_pull_up>;
};
};
pcie {
pcie_pwr: pcie-pwr {
rockchip,pins = <4 RK_PD4 RK_FUNC_GPIO &pcfg_pull_up>;
};
};
pmic {
pmic_int_l: pmic-int-l {
rockchip,pins = <1 RK_PC2 0 &pcfg_pull_up>;
};
};
vbus_host {
usb1_en_oc: usb1-en-oc {
rockchip,pins = <4 RK_PD1 RK_FUNC_GPIO &pcfg_pull_up>;
};
};
vbus_typec {
usb0_en_oc: usb0-en-oc {
rockchip,pins = <4 RK_PD2 RK_FUNC_GPIO &pcfg_pull_up>;
};
};
};
&pmu_io_domains {
status = "okay";
pmu1830-supply = <&vcc_1v8>;
};
&sdhci {
bus-width = <8>;
mmc-hs400-1_8v;
mmc-hs400-enhanced-strobe;
non-removable;
status = "okay";
};
&sdmmc {
cd-gpios = <&gpio0 RK_PA7 GPIO_ACTIVE_LOW>;
max-frequency = <150000000>;
};
&tcphy0 {
status = "okay";
};
&tsadc {
rockchip,hw-tshut-mode = <1>;
rockchip,hw-tshut-polarity = <1>;
status = "okay";
};
&u2phy0 {
status = "okay";
u2phy0_otg: otg-port {
phy-supply = <&vbus_typec>;
status = "okay";
};
u2phy0_host: host-port {
phy-supply = <&vbus_host>;
status = "okay";
};
};
&u2phy1 {
status = "okay";
u2phy1_host: host-port {
phy-supply = <&vbus_host>;
status = "okay";
};
};
&usb_host0_ehci {
status = "okay";
};
&usb_host0_ohci {
status = "okay";
};
&usb_host1_ehci {
status = "okay";
};
&usb_host1_ohci {
status = "okay";
};
&usbdrd3_0 {
status = "okay";
};
&usbdrd_dwc3_0 {
status = "okay";
};
&vbus_host {
enable-active-high;
gpio = <&gpio4 RK_PD1 GPIO_ACTIVE_HIGH>; /* USB1_EN_OC# */
pinctrl-names = "default";
pinctrl-0 = <&usb1_en_oc>;
};
&vbus_typec {
enable-active-high;
gpio = <&gpio4 RK_PD2 GPIO_ACTIVE_HIGH>; /* USB0_EN_OC# */
pinctrl-names = "default";
pinctrl-0 = <&usb0_en_oc>;
};