| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Renesas SDHI |
| * |
| * Copyright (C) 2015-19 Renesas Electronics Corporation |
| * Copyright (C) 2016-19 Sang Engineering, Wolfram Sang |
| * Copyright (C) 2016-17 Horms Solutions, Simon Horman |
| * Copyright (C) 2009 Magnus Damm |
| * |
| * Based on "Compaq ASIC3 support": |
| * |
| * Copyright 2001 Compaq Computer Corporation. |
| * Copyright 2004-2005 Phil Blundell |
| * Copyright 2007-2008 OpenedHand Ltd. |
| * |
| * Authors: Phil Blundell <pb@handhelds.org>, |
| * Samuel Ortiz <sameo@openedhand.com> |
| * |
| */ |
| |
| #include <linux/clk.h> |
| #include <linux/delay.h> |
| #include <linux/iopoll.h> |
| #include <linux/kernel.h> |
| #include <linux/mfd/tmio.h> |
| #include <linux/mmc/host.h> |
| #include <linux/mmc/mmc.h> |
| #include <linux/mmc/slot-gpio.h> |
| #include <linux/module.h> |
| #include <linux/of_device.h> |
| #include <linux/pinctrl/consumer.h> |
| #include <linux/pinctrl/pinctrl-state.h> |
| #include <linux/platform_device.h> |
| #include <linux/pm_domain.h> |
| #include <linux/regulator/consumer.h> |
| #include <linux/reset.h> |
| #include <linux/sh_dma.h> |
| #include <linux/slab.h> |
| #include <linux/sys_soc.h> |
| |
| #include "renesas_sdhi.h" |
| #include "tmio_mmc.h" |
| |
| #define CTL_HOST_MODE 0xe4 |
| #define HOST_MODE_GEN2_SDR50_WMODE BIT(0) |
| #define HOST_MODE_GEN2_SDR104_WMODE BIT(0) |
| #define HOST_MODE_GEN3_WMODE BIT(0) |
| #define HOST_MODE_GEN3_BUSWIDTH BIT(8) |
| |
| #define HOST_MODE_GEN3_16BIT HOST_MODE_GEN3_WMODE |
| #define HOST_MODE_GEN3_32BIT (HOST_MODE_GEN3_WMODE | HOST_MODE_GEN3_BUSWIDTH) |
| #define HOST_MODE_GEN3_64BIT 0 |
| |
| #define CTL_SDIF_MODE 0xe6 |
| #define SDIF_MODE_HS400 BIT(0) |
| |
| #define SDHI_VER_GEN2_SDR50 0x490c |
| #define SDHI_VER_RZ_A1 0x820b |
| /* very old datasheets said 0x490c for SDR104, too. They are wrong! */ |
| #define SDHI_VER_GEN2_SDR104 0xcb0d |
| #define SDHI_VER_GEN3_SD 0xcc10 |
| #define SDHI_VER_GEN3_SDMMC 0xcd10 |
| |
| #define SDHI_GEN3_MMC0_ADDR 0xee140000 |
| |
| static void renesas_sdhi_sdbuf_width(struct tmio_mmc_host *host, int width) |
| { |
| u32 val; |
| |
| /* |
| * see also |
| * renesas_sdhi_of_data :: dma_buswidth |
| */ |
| switch (sd_ctrl_read16(host, CTL_VERSION)) { |
| case SDHI_VER_GEN2_SDR50: |
| val = (width == 32) ? HOST_MODE_GEN2_SDR50_WMODE : 0; |
| break; |
| case SDHI_VER_GEN2_SDR104: |
| val = (width == 32) ? 0 : HOST_MODE_GEN2_SDR104_WMODE; |
| break; |
| case SDHI_VER_GEN3_SD: |
| case SDHI_VER_GEN3_SDMMC: |
| if (width == 64) |
| val = HOST_MODE_GEN3_64BIT; |
| else if (width == 32) |
| val = HOST_MODE_GEN3_32BIT; |
| else |
| val = HOST_MODE_GEN3_16BIT; |
| break; |
| default: |
| /* nothing to do */ |
| return; |
| } |
| |
| sd_ctrl_write16(host, CTL_HOST_MODE, val); |
| } |
| |
| static int renesas_sdhi_clk_enable(struct tmio_mmc_host *host) |
| { |
| struct mmc_host *mmc = host->mmc; |
| struct renesas_sdhi *priv = host_to_priv(host); |
| int ret; |
| |
| ret = clk_prepare_enable(priv->clk_cd); |
| if (ret < 0) |
| return ret; |
| |
| /* |
| * The clock driver may not know what maximum frequency |
| * actually works, so it should be set with the max-frequency |
| * property which will already have been read to f_max. If it |
| * was missing, assume the current frequency is the maximum. |
| */ |
| if (!mmc->f_max) |
| mmc->f_max = clk_get_rate(priv->clk); |
| |
| /* |
| * Minimum frequency is the minimum input clock frequency |
| * divided by our maximum divider. |
| */ |
| mmc->f_min = max(clk_round_rate(priv->clk, 1) / 512, 1L); |
| |
| /* enable 16bit data access on SDBUF as default */ |
| renesas_sdhi_sdbuf_width(host, 16); |
| |
| return 0; |
| } |
| |
| static unsigned int renesas_sdhi_clk_update(struct tmio_mmc_host *host, |
| unsigned int new_clock) |
| { |
| struct renesas_sdhi *priv = host_to_priv(host); |
| unsigned int freq, diff, best_freq = 0, diff_min = ~0; |
| int i; |
| |
| /* |
| * We simply return the current rate if a) we are not on a R-Car Gen2+ |
| * SoC (may work for others, but untested) or b) if the SCC needs its |
| * clock during tuning, so we don't change the external clock setup. |
| */ |
| if (!(host->pdata->flags & TMIO_MMC_MIN_RCAR2) || mmc_doing_tune(host->mmc)) |
| return clk_get_rate(priv->clk); |
| |
| /* |
| * We want the bus clock to be as close as possible to, but no |
| * greater than, new_clock. As we can divide by 1 << i for |
| * any i in [0, 9] we want the input clock to be as close as |
| * possible, but no greater than, new_clock << i. |
| */ |
| for (i = min(9, ilog2(UINT_MAX / new_clock)); i >= 0; i--) { |
| freq = clk_round_rate(priv->clk, new_clock << i); |
| if (freq > (new_clock << i)) { |
| /* Too fast; look for a slightly slower option */ |
| freq = clk_round_rate(priv->clk, |
| (new_clock << i) / 4 * 3); |
| if (freq > (new_clock << i)) |
| continue; |
| } |
| |
| diff = new_clock - (freq >> i); |
| if (diff <= diff_min) { |
| best_freq = freq; |
| diff_min = diff; |
| } |
| } |
| |
| clk_set_rate(priv->clk, best_freq); |
| |
| return clk_get_rate(priv->clk); |
| } |
| |
| static void renesas_sdhi_set_clock(struct tmio_mmc_host *host, |
| unsigned int new_clock) |
| { |
| u32 clk = 0, clock; |
| |
| sd_ctrl_write16(host, CTL_SD_CARD_CLK_CTL, ~CLK_CTL_SCLKEN & |
| sd_ctrl_read16(host, CTL_SD_CARD_CLK_CTL)); |
| |
| if (new_clock == 0) { |
| host->mmc->actual_clock = 0; |
| goto out; |
| } |
| |
| host->mmc->actual_clock = renesas_sdhi_clk_update(host, new_clock); |
| clock = host->mmc->actual_clock / 512; |
| |
| for (clk = 0x80000080; new_clock >= (clock << 1); clk >>= 1) |
| clock <<= 1; |
| |
| /* 1/1 clock is option */ |
| if ((host->pdata->flags & TMIO_MMC_CLK_ACTUAL) && ((clk >> 22) & 0x1)) { |
| if (!(host->mmc->ios.timing == MMC_TIMING_MMC_HS400)) |
| clk |= 0xff; |
| else |
| clk &= ~0xff; |
| } |
| |
| sd_ctrl_write16(host, CTL_SD_CARD_CLK_CTL, clk & CLK_CTL_DIV_MASK); |
| if (!(host->pdata->flags & TMIO_MMC_MIN_RCAR2)) |
| usleep_range(10000, 11000); |
| |
| sd_ctrl_write16(host, CTL_SD_CARD_CLK_CTL, CLK_CTL_SCLKEN | |
| sd_ctrl_read16(host, CTL_SD_CARD_CLK_CTL)); |
| |
| out: |
| /* HW engineers overrode docs: no sleep needed on R-Car2+ */ |
| if (!(host->pdata->flags & TMIO_MMC_MIN_RCAR2)) |
| usleep_range(10000, 11000); |
| } |
| |
| static void renesas_sdhi_clk_disable(struct tmio_mmc_host *host) |
| { |
| struct renesas_sdhi *priv = host_to_priv(host); |
| |
| clk_disable_unprepare(priv->clk_cd); |
| } |
| |
| static int renesas_sdhi_card_busy(struct mmc_host *mmc) |
| { |
| struct tmio_mmc_host *host = mmc_priv(mmc); |
| |
| return !(sd_ctrl_read16_and_16_as_32(host, CTL_STATUS) & |
| TMIO_STAT_DAT0); |
| } |
| |
| static int renesas_sdhi_start_signal_voltage_switch(struct mmc_host *mmc, |
| struct mmc_ios *ios) |
| { |
| struct tmio_mmc_host *host = mmc_priv(mmc); |
| struct renesas_sdhi *priv = host_to_priv(host); |
| struct pinctrl_state *pin_state; |
| int ret; |
| |
| switch (ios->signal_voltage) { |
| case MMC_SIGNAL_VOLTAGE_330: |
| pin_state = priv->pins_default; |
| break; |
| case MMC_SIGNAL_VOLTAGE_180: |
| pin_state = priv->pins_uhs; |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| /* |
| * If anything is missing, assume signal voltage is fixed at |
| * 3.3V and succeed/fail accordingly. |
| */ |
| if (IS_ERR(priv->pinctrl) || IS_ERR(pin_state)) |
| return ios->signal_voltage == |
| MMC_SIGNAL_VOLTAGE_330 ? 0 : -EINVAL; |
| |
| ret = mmc_regulator_set_vqmmc(host->mmc, ios); |
| if (ret < 0) |
| return ret; |
| |
| return pinctrl_select_state(priv->pinctrl, pin_state); |
| } |
| |
| /* SCC registers */ |
| #define SH_MOBILE_SDHI_SCC_DTCNTL 0x000 |
| #define SH_MOBILE_SDHI_SCC_TAPSET 0x002 |
| #define SH_MOBILE_SDHI_SCC_DT2FF 0x004 |
| #define SH_MOBILE_SDHI_SCC_CKSEL 0x006 |
| #define SH_MOBILE_SDHI_SCC_RVSCNTL 0x008 |
| #define SH_MOBILE_SDHI_SCC_RVSREQ 0x00A |
| #define SH_MOBILE_SDHI_SCC_SMPCMP 0x00C |
| #define SH_MOBILE_SDHI_SCC_TMPPORT2 0x00E |
| #define SH_MOBILE_SDHI_SCC_TMPPORT3 0x014 |
| #define SH_MOBILE_SDHI_SCC_TMPPORT4 0x016 |
| #define SH_MOBILE_SDHI_SCC_TMPPORT5 0x018 |
| #define SH_MOBILE_SDHI_SCC_TMPPORT6 0x01A |
| #define SH_MOBILE_SDHI_SCC_TMPPORT7 0x01C |
| |
| #define SH_MOBILE_SDHI_SCC_DTCNTL_TAPEN BIT(0) |
| #define SH_MOBILE_SDHI_SCC_DTCNTL_TAPNUM_SHIFT 16 |
| #define SH_MOBILE_SDHI_SCC_DTCNTL_TAPNUM_MASK 0xff |
| |
| #define SH_MOBILE_SDHI_SCC_CKSEL_DTSEL BIT(0) |
| |
| #define SH_MOBILE_SDHI_SCC_RVSCNTL_RVSEN BIT(0) |
| |
| #define SH_MOBILE_SDHI_SCC_RVSREQ_REQTAPDOWN BIT(0) |
| #define SH_MOBILE_SDHI_SCC_RVSREQ_REQTAPUP BIT(1) |
| #define SH_MOBILE_SDHI_SCC_RVSREQ_RVSERR BIT(2) |
| |
| #define SH_MOBILE_SDHI_SCC_SMPCMP_CMD_REQDOWN BIT(8) |
| #define SH_MOBILE_SDHI_SCC_SMPCMP_CMD_REQUP BIT(24) |
| #define SH_MOBILE_SDHI_SCC_SMPCMP_CMD_ERR (BIT(8) | BIT(24)) |
| |
| #define SH_MOBILE_SDHI_SCC_TMPPORT2_HS400OSEL BIT(4) |
| #define SH_MOBILE_SDHI_SCC_TMPPORT2_HS400EN BIT(31) |
| |
| /* Definitions for values the SH_MOBILE_SDHI_SCC_TMPPORT4 register */ |
| #define SH_MOBILE_SDHI_SCC_TMPPORT4_DLL_ACC_START BIT(0) |
| |
| /* Definitions for values the SH_MOBILE_SDHI_SCC_TMPPORT5 register */ |
| #define SH_MOBILE_SDHI_SCC_TMPPORT5_DLL_RW_SEL_R BIT(8) |
| #define SH_MOBILE_SDHI_SCC_TMPPORT5_DLL_RW_SEL_W (0 << 8) |
| #define SH_MOBILE_SDHI_SCC_TMPPORT5_DLL_ADR_MASK 0x3F |
| |
| /* Definitions for values the SH_MOBILE_SDHI_SCC register */ |
| #define SH_MOBILE_SDHI_SCC_TMPPORT_DISABLE_WP_CODE 0xa5000000 |
| #define SH_MOBILE_SDHI_SCC_TMPPORT_CALIB_CODE_MASK 0x1f |
| #define SH_MOBILE_SDHI_SCC_TMPPORT_MANUAL_MODE BIT(7) |
| |
| static const u8 r8a7796_es13_calib_table[2][SDHI_CALIB_TABLE_MAX] = { |
| { 3, 3, 3, 3, 3, 3, 3, 4, 4, 5, 6, 7, 8, 9, 10, 15, |
| 16, 16, 16, 16, 16, 16, 17, 18, 18, 19, 20, 21, 22, 23, 24, 25 }, |
| { 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 6, 7, 8, 11, |
| 12, 17, 18, 18, 18, 18, 18, 18, 18, 19, 20, 21, 22, 23, 25, 25 } |
| }; |
| |
| static const u8 r8a77965_calib_table[2][SDHI_CALIB_TABLE_MAX] = { |
| { 1, 2, 6, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 15, 15, 16, |
| 17, 18, 19, 20, 21, 22, 23, 24, 25, 25, 26, 27, 28, 29, 30, 31 }, |
| { 2, 3, 4, 4, 5, 6, 7, 9, 10, 11, 12, 13, 14, 15, 16, 17, |
| 17, 17, 20, 21, 22, 23, 24, 25, 27, 28, 29, 30, 31, 31, 31, 31 } |
| }; |
| |
| static const u8 r8a77990_calib_table[2][SDHI_CALIB_TABLE_MAX] = { |
| { 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, |
| 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 }, |
| { 0, 0, 0, 1, 2, 3, 3, 4, 4, 4, 5, 5, 6, 8, 9, 10, |
| 11, 12, 13, 15, 16, 17, 17, 18, 18, 19, 20, 22, 24, 25, 26, 26 } |
| }; |
| |
| static inline u32 sd_scc_read32(struct tmio_mmc_host *host, |
| struct renesas_sdhi *priv, int addr) |
| { |
| return readl(priv->scc_ctl + (addr << host->bus_shift)); |
| } |
| |
| static inline void sd_scc_write32(struct tmio_mmc_host *host, |
| struct renesas_sdhi *priv, |
| int addr, u32 val) |
| { |
| writel(val, priv->scc_ctl + (addr << host->bus_shift)); |
| } |
| |
| static unsigned int renesas_sdhi_init_tuning(struct tmio_mmc_host *host) |
| { |
| struct renesas_sdhi *priv; |
| |
| priv = host_to_priv(host); |
| |
| /* Initialize SCC */ |
| sd_ctrl_write32_as_16_and_16(host, CTL_STATUS, 0x0); |
| |
| sd_ctrl_write16(host, CTL_SD_CARD_CLK_CTL, ~CLK_CTL_SCLKEN & |
| sd_ctrl_read16(host, CTL_SD_CARD_CLK_CTL)); |
| |
| /* set sampling clock selection range */ |
| sd_scc_write32(host, priv, SH_MOBILE_SDHI_SCC_DTCNTL, |
| SH_MOBILE_SDHI_SCC_DTCNTL_TAPEN | |
| 0x8 << SH_MOBILE_SDHI_SCC_DTCNTL_TAPNUM_SHIFT); |
| |
| sd_scc_write32(host, priv, SH_MOBILE_SDHI_SCC_CKSEL, |
| SH_MOBILE_SDHI_SCC_CKSEL_DTSEL | |
| sd_scc_read32(host, priv, SH_MOBILE_SDHI_SCC_CKSEL)); |
| |
| sd_scc_write32(host, priv, SH_MOBILE_SDHI_SCC_RVSCNTL, |
| ~SH_MOBILE_SDHI_SCC_RVSCNTL_RVSEN & |
| sd_scc_read32(host, priv, SH_MOBILE_SDHI_SCC_RVSCNTL)); |
| |
| sd_scc_write32(host, priv, SH_MOBILE_SDHI_SCC_DT2FF, priv->scc_tappos); |
| |
| sd_ctrl_write16(host, CTL_SD_CARD_CLK_CTL, CLK_CTL_SCLKEN | |
| sd_ctrl_read16(host, CTL_SD_CARD_CLK_CTL)); |
| |
| /* Read TAPNUM */ |
| return (sd_scc_read32(host, priv, SH_MOBILE_SDHI_SCC_DTCNTL) >> |
| SH_MOBILE_SDHI_SCC_DTCNTL_TAPNUM_SHIFT) & |
| SH_MOBILE_SDHI_SCC_DTCNTL_TAPNUM_MASK; |
| } |
| |
| static void renesas_sdhi_hs400_complete(struct mmc_host *mmc) |
| { |
| struct tmio_mmc_host *host = mmc_priv(mmc); |
| struct renesas_sdhi *priv = host_to_priv(host); |
| u32 bad_taps = priv->quirks ? priv->quirks->hs400_bad_taps : 0; |
| bool use_4tap = priv->quirks && priv->quirks->hs400_4taps; |
| |
| sd_ctrl_write16(host, CTL_SD_CARD_CLK_CTL, ~CLK_CTL_SCLKEN & |
| sd_ctrl_read16(host, CTL_SD_CARD_CLK_CTL)); |
| |
| /* Set HS400 mode */ |
| sd_ctrl_write16(host, CTL_SDIF_MODE, SDIF_MODE_HS400 | |
| sd_ctrl_read16(host, CTL_SDIF_MODE)); |
| |
| sd_scc_write32(host, priv, SH_MOBILE_SDHI_SCC_DT2FF, |
| priv->scc_tappos_hs400); |
| |
| /* Gen3 can't do automatic tap correction with HS400, so disable it */ |
| if (sd_ctrl_read16(host, CTL_VERSION) == SDHI_VER_GEN3_SDMMC) |
| sd_scc_write32(host, priv, SH_MOBILE_SDHI_SCC_RVSCNTL, |
| ~SH_MOBILE_SDHI_SCC_RVSCNTL_RVSEN & |
| sd_scc_read32(host, priv, SH_MOBILE_SDHI_SCC_RVSCNTL)); |
| |
| sd_scc_write32(host, priv, SH_MOBILE_SDHI_SCC_TMPPORT2, |
| (SH_MOBILE_SDHI_SCC_TMPPORT2_HS400EN | |
| SH_MOBILE_SDHI_SCC_TMPPORT2_HS400OSEL) | |
| sd_scc_read32(host, priv, SH_MOBILE_SDHI_SCC_TMPPORT2)); |
| |
| /* Set the sampling clock selection range of HS400 mode */ |
| sd_scc_write32(host, priv, SH_MOBILE_SDHI_SCC_DTCNTL, |
| SH_MOBILE_SDHI_SCC_DTCNTL_TAPEN | |
| 0x4 << SH_MOBILE_SDHI_SCC_DTCNTL_TAPNUM_SHIFT); |
| |
| /* Avoid bad TAP */ |
| if (bad_taps & BIT(priv->tap_set)) { |
| u32 new_tap = (priv->tap_set + 1) % priv->tap_num; |
| |
| if (bad_taps & BIT(new_tap)) |
| new_tap = (priv->tap_set - 1) % priv->tap_num; |
| |
| if (bad_taps & BIT(new_tap)) { |
| new_tap = priv->tap_set; |
| dev_dbg(&host->pdev->dev, "Can't handle three bad tap in a row\n"); |
| } |
| |
| priv->tap_set = new_tap; |
| } |
| |
| sd_scc_write32(host, priv, SH_MOBILE_SDHI_SCC_TAPSET, |
| priv->tap_set / (use_4tap ? 2 : 1)); |
| |
| sd_scc_write32(host, priv, SH_MOBILE_SDHI_SCC_CKSEL, |
| SH_MOBILE_SDHI_SCC_CKSEL_DTSEL | |
| sd_scc_read32(host, priv, SH_MOBILE_SDHI_SCC_CKSEL)); |
| |
| sd_ctrl_write16(host, CTL_SD_CARD_CLK_CTL, CLK_CTL_SCLKEN | |
| sd_ctrl_read16(host, CTL_SD_CARD_CLK_CTL)); |
| |
| if (priv->adjust_hs400_calib_table) |
| priv->needs_adjust_hs400 = true; |
| } |
| |
| static void renesas_sdhi_disable_scc(struct mmc_host *mmc) |
| { |
| struct tmio_mmc_host *host = mmc_priv(mmc); |
| struct renesas_sdhi *priv = host_to_priv(host); |
| |
| sd_ctrl_write16(host, CTL_SD_CARD_CLK_CTL, ~CLK_CTL_SCLKEN & |
| sd_ctrl_read16(host, CTL_SD_CARD_CLK_CTL)); |
| |
| sd_scc_write32(host, priv, SH_MOBILE_SDHI_SCC_CKSEL, |
| ~SH_MOBILE_SDHI_SCC_CKSEL_DTSEL & |
| sd_scc_read32(host, priv, |
| SH_MOBILE_SDHI_SCC_CKSEL)); |
| |
| sd_scc_write32(host, priv, SH_MOBILE_SDHI_SCC_DTCNTL, |
| ~SH_MOBILE_SDHI_SCC_DTCNTL_TAPEN & |
| sd_scc_read32(host, priv, |
| SH_MOBILE_SDHI_SCC_DTCNTL)); |
| |
| sd_ctrl_write16(host, CTL_SD_CARD_CLK_CTL, CLK_CTL_SCLKEN | |
| sd_ctrl_read16(host, CTL_SD_CARD_CLK_CTL)); |
| } |
| |
| static u32 sd_scc_tmpport_read32(struct tmio_mmc_host *host, |
| struct renesas_sdhi *priv, u32 addr) |
| { |
| /* read mode */ |
| sd_scc_write32(host, priv, SH_MOBILE_SDHI_SCC_TMPPORT5, |
| SH_MOBILE_SDHI_SCC_TMPPORT5_DLL_RW_SEL_R | |
| (SH_MOBILE_SDHI_SCC_TMPPORT5_DLL_ADR_MASK & addr)); |
| |
| /* access start and stop */ |
| sd_scc_write32(host, priv, SH_MOBILE_SDHI_SCC_TMPPORT4, |
| SH_MOBILE_SDHI_SCC_TMPPORT4_DLL_ACC_START); |
| sd_scc_write32(host, priv, SH_MOBILE_SDHI_SCC_TMPPORT4, 0); |
| |
| return sd_scc_read32(host, priv, SH_MOBILE_SDHI_SCC_TMPPORT7); |
| } |
| |
| static void sd_scc_tmpport_write32(struct tmio_mmc_host *host, |
| struct renesas_sdhi *priv, u32 addr, u32 val) |
| { |
| /* write mode */ |
| sd_scc_write32(host, priv, SH_MOBILE_SDHI_SCC_TMPPORT5, |
| SH_MOBILE_SDHI_SCC_TMPPORT5_DLL_RW_SEL_W | |
| (SH_MOBILE_SDHI_SCC_TMPPORT5_DLL_ADR_MASK & addr)); |
| |
| sd_scc_write32(host, priv, SH_MOBILE_SDHI_SCC_TMPPORT6, val); |
| |
| /* access start and stop */ |
| sd_scc_write32(host, priv, SH_MOBILE_SDHI_SCC_TMPPORT4, |
| SH_MOBILE_SDHI_SCC_TMPPORT4_DLL_ACC_START); |
| sd_scc_write32(host, priv, SH_MOBILE_SDHI_SCC_TMPPORT4, 0); |
| } |
| |
| static void renesas_sdhi_adjust_hs400_mode_enable(struct tmio_mmc_host *host) |
| { |
| struct renesas_sdhi *priv = host_to_priv(host); |
| u32 calib_code; |
| |
| /* disable write protect */ |
| sd_scc_tmpport_write32(host, priv, 0x00, |
| SH_MOBILE_SDHI_SCC_TMPPORT_DISABLE_WP_CODE); |
| /* read calibration code and adjust */ |
| calib_code = sd_scc_tmpport_read32(host, priv, 0x26); |
| calib_code &= SH_MOBILE_SDHI_SCC_TMPPORT_CALIB_CODE_MASK; |
| |
| sd_scc_tmpport_write32(host, priv, 0x22, |
| SH_MOBILE_SDHI_SCC_TMPPORT_MANUAL_MODE | |
| priv->adjust_hs400_calib_table[calib_code]); |
| |
| /* set offset value to TMPPORT3, hardcoded to OFFSET0 (= 0x3) for now */ |
| sd_scc_write32(host, priv, SH_MOBILE_SDHI_SCC_TMPPORT3, 0x3); |
| |
| /* adjustment done, clear flag */ |
| priv->needs_adjust_hs400 = false; |
| } |
| |
| static void renesas_sdhi_adjust_hs400_mode_disable(struct tmio_mmc_host *host) |
| { |
| struct renesas_sdhi *priv = host_to_priv(host); |
| |
| /* disable write protect */ |
| sd_scc_tmpport_write32(host, priv, 0x00, |
| SH_MOBILE_SDHI_SCC_TMPPORT_DISABLE_WP_CODE); |
| /* disable manual calibration */ |
| sd_scc_tmpport_write32(host, priv, 0x22, 0); |
| /* clear offset value of TMPPORT3 */ |
| sd_scc_write32(host, priv, SH_MOBILE_SDHI_SCC_TMPPORT3, 0); |
| } |
| |
| static void renesas_sdhi_reset_hs400_mode(struct tmio_mmc_host *host, |
| struct renesas_sdhi *priv) |
| { |
| sd_ctrl_write16(host, CTL_SD_CARD_CLK_CTL, ~CLK_CTL_SCLKEN & |
| sd_ctrl_read16(host, CTL_SD_CARD_CLK_CTL)); |
| |
| /* Reset HS400 mode */ |
| sd_ctrl_write16(host, CTL_SDIF_MODE, ~SDIF_MODE_HS400 & |
| sd_ctrl_read16(host, CTL_SDIF_MODE)); |
| |
| sd_scc_write32(host, priv, SH_MOBILE_SDHI_SCC_DT2FF, priv->scc_tappos); |
| |
| sd_scc_write32(host, priv, SH_MOBILE_SDHI_SCC_TMPPORT2, |
| ~(SH_MOBILE_SDHI_SCC_TMPPORT2_HS400EN | |
| SH_MOBILE_SDHI_SCC_TMPPORT2_HS400OSEL) & |
| sd_scc_read32(host, priv, SH_MOBILE_SDHI_SCC_TMPPORT2)); |
| |
| if (priv->adjust_hs400_calib_table) |
| renesas_sdhi_adjust_hs400_mode_disable(host); |
| |
| sd_ctrl_write16(host, CTL_SD_CARD_CLK_CTL, CLK_CTL_SCLKEN | |
| sd_ctrl_read16(host, CTL_SD_CARD_CLK_CTL)); |
| } |
| |
| static int renesas_sdhi_prepare_hs400_tuning(struct mmc_host *mmc, struct mmc_ios *ios) |
| { |
| struct tmio_mmc_host *host = mmc_priv(mmc); |
| |
| renesas_sdhi_reset_hs400_mode(host, host_to_priv(host)); |
| return 0; |
| } |
| |
| static void renesas_sdhi_scc_reset(struct tmio_mmc_host *host, struct renesas_sdhi *priv) |
| { |
| renesas_sdhi_disable_scc(host->mmc); |
| renesas_sdhi_reset_hs400_mode(host, priv); |
| priv->needs_adjust_hs400 = false; |
| |
| sd_scc_write32(host, priv, SH_MOBILE_SDHI_SCC_RVSCNTL, |
| ~SH_MOBILE_SDHI_SCC_RVSCNTL_RVSEN & |
| sd_scc_read32(host, priv, SH_MOBILE_SDHI_SCC_RVSCNTL)); |
| } |
| |
| /* only populated for TMIO_MMC_MIN_RCAR2 */ |
| static void renesas_sdhi_reset(struct tmio_mmc_host *host) |
| { |
| struct renesas_sdhi *priv = host_to_priv(host); |
| int ret; |
| u16 val; |
| |
| if (priv->rstc) { |
| reset_control_reset(priv->rstc); |
| /* Unknown why but without polling reset status, it will hang */ |
| read_poll_timeout(reset_control_status, ret, ret == 0, 1, 100, |
| false, priv->rstc); |
| priv->needs_adjust_hs400 = false; |
| renesas_sdhi_set_clock(host, host->clk_cache); |
| } else if (priv->scc_ctl) { |
| renesas_sdhi_scc_reset(host, priv); |
| } |
| |
| if (sd_ctrl_read16(host, CTL_VERSION) >= SDHI_VER_GEN3_SD) { |
| val = sd_ctrl_read16(host, CTL_SD_MEM_CARD_OPT); |
| val |= CARD_OPT_EXTOP; |
| sd_ctrl_write16(host, CTL_SD_MEM_CARD_OPT, val); |
| } |
| } |
| |
| static unsigned int renesas_sdhi_gen3_get_cycles(struct tmio_mmc_host *host) |
| { |
| u16 num, val = sd_ctrl_read16(host, CTL_SD_MEM_CARD_OPT); |
| |
| num = (val & CARD_OPT_TOP_MASK) >> CARD_OPT_TOP_SHIFT; |
| return 1 << ((val & CARD_OPT_EXTOP ? 14 : 13) + num); |
| |
| } |
| |
| #define SH_MOBILE_SDHI_MIN_TAP_ROW 3 |
| |
| static int renesas_sdhi_select_tuning(struct tmio_mmc_host *host) |
| { |
| struct renesas_sdhi *priv = host_to_priv(host); |
| unsigned int tap_start = 0, tap_end = 0, tap_cnt = 0, rs, re, i; |
| unsigned int taps_size = priv->tap_num * 2, min_tap_row; |
| unsigned long *bitmap; |
| |
| sd_scc_write32(host, priv, SH_MOBILE_SDHI_SCC_RVSREQ, 0); |
| |
| /* |
| * When tuning CMD19 is issued twice for each tap, merge the |
| * result requiring the tap to be good in both runs before |
| * considering it for tuning selection. |
| */ |
| for (i = 0; i < taps_size; i++) { |
| int offset = priv->tap_num * (i < priv->tap_num ? 1 : -1); |
| |
| if (!test_bit(i, priv->taps)) |
| clear_bit(i + offset, priv->taps); |
| |
| if (!test_bit(i, priv->smpcmp)) |
| clear_bit(i + offset, priv->smpcmp); |
| } |
| |
| /* |
| * If all TAP are OK, the sampling clock position is selected by |
| * identifying the change point of data. |
| */ |
| if (bitmap_full(priv->taps, taps_size)) { |
| bitmap = priv->smpcmp; |
| min_tap_row = 1; |
| } else { |
| bitmap = priv->taps; |
| min_tap_row = SH_MOBILE_SDHI_MIN_TAP_ROW; |
| } |
| |
| /* |
| * Find the longest consecutive run of successful probes. If that |
| * is at least SH_MOBILE_SDHI_MIN_TAP_ROW probes long then use the |
| * center index as the tap, otherwise bail out. |
| */ |
| bitmap_for_each_set_region(bitmap, rs, re, 0, taps_size) { |
| if (re - rs > tap_cnt) { |
| tap_end = re; |
| tap_start = rs; |
| tap_cnt = tap_end - tap_start; |
| } |
| } |
| |
| if (tap_cnt >= min_tap_row) |
| priv->tap_set = (tap_start + tap_end) / 2 % priv->tap_num; |
| else |
| return -EIO; |
| |
| /* Set SCC */ |
| sd_scc_write32(host, priv, SH_MOBILE_SDHI_SCC_TAPSET, priv->tap_set); |
| |
| /* Enable auto re-tuning */ |
| sd_scc_write32(host, priv, SH_MOBILE_SDHI_SCC_RVSCNTL, |
| SH_MOBILE_SDHI_SCC_RVSCNTL_RVSEN | |
| sd_scc_read32(host, priv, SH_MOBILE_SDHI_SCC_RVSCNTL)); |
| |
| return 0; |
| } |
| |
| static int renesas_sdhi_execute_tuning(struct mmc_host *mmc, u32 opcode) |
| { |
| struct tmio_mmc_host *host = mmc_priv(mmc); |
| struct renesas_sdhi *priv = host_to_priv(host); |
| int i, ret; |
| |
| priv->tap_num = renesas_sdhi_init_tuning(host); |
| if (!priv->tap_num) |
| return 0; /* Tuning is not supported */ |
| |
| if (priv->tap_num * 2 >= sizeof(priv->taps) * BITS_PER_BYTE) { |
| dev_err(&host->pdev->dev, |
| "Too many taps, please update 'taps' in tmio_mmc_host!\n"); |
| return -EINVAL; |
| } |
| |
| bitmap_zero(priv->taps, priv->tap_num * 2); |
| bitmap_zero(priv->smpcmp, priv->tap_num * 2); |
| |
| /* Issue CMD19 twice for each tap */ |
| for (i = 0; i < 2 * priv->tap_num; i++) { |
| int cmd_error; |
| |
| /* Set sampling clock position */ |
| sd_scc_write32(host, priv, SH_MOBILE_SDHI_SCC_TAPSET, i % priv->tap_num); |
| |
| if (mmc_send_tuning(mmc, opcode, &cmd_error) == 0) |
| set_bit(i, priv->taps); |
| |
| if (sd_scc_read32(host, priv, SH_MOBILE_SDHI_SCC_SMPCMP) == 0) |
| set_bit(i, priv->smpcmp); |
| |
| if (cmd_error) |
| mmc_abort_tuning(mmc, opcode); |
| } |
| |
| ret = renesas_sdhi_select_tuning(host); |
| if (ret < 0) |
| renesas_sdhi_scc_reset(host, priv); |
| return ret; |
| } |
| |
| static bool renesas_sdhi_manual_correction(struct tmio_mmc_host *host, bool use_4tap) |
| { |
| struct renesas_sdhi *priv = host_to_priv(host); |
| unsigned int new_tap = priv->tap_set, error_tap = priv->tap_set; |
| u32 val; |
| |
| val = sd_scc_read32(host, priv, SH_MOBILE_SDHI_SCC_RVSREQ); |
| if (!val) |
| return false; |
| |
| sd_scc_write32(host, priv, SH_MOBILE_SDHI_SCC_RVSREQ, 0); |
| |
| /* Change TAP position according to correction status */ |
| if (sd_ctrl_read16(host, CTL_VERSION) == SDHI_VER_GEN3_SDMMC && |
| host->mmc->ios.timing == MMC_TIMING_MMC_HS400) { |
| u32 bad_taps = priv->quirks ? priv->quirks->hs400_bad_taps : 0; |
| /* |
| * With HS400, the DAT signal is based on DS, not CLK. |
| * Therefore, use only CMD status. |
| */ |
| u32 smpcmp = sd_scc_read32(host, priv, SH_MOBILE_SDHI_SCC_SMPCMP) & |
| SH_MOBILE_SDHI_SCC_SMPCMP_CMD_ERR; |
| if (!smpcmp) { |
| return false; /* no error in CMD signal */ |
| } else if (smpcmp == SH_MOBILE_SDHI_SCC_SMPCMP_CMD_REQUP) { |
| new_tap++; |
| error_tap--; |
| } else if (smpcmp == SH_MOBILE_SDHI_SCC_SMPCMP_CMD_REQDOWN) { |
| new_tap--; |
| error_tap++; |
| } else { |
| return true; /* need retune */ |
| } |
| |
| /* |
| * When new_tap is a bad tap, we cannot change. Then, we compare |
| * with the HS200 tuning result. When smpcmp[error_tap] is OK, |
| * we can at least retune. |
| */ |
| if (bad_taps & BIT(new_tap % priv->tap_num)) |
| return test_bit(error_tap % priv->tap_num, priv->smpcmp); |
| } else { |
| if (val & SH_MOBILE_SDHI_SCC_RVSREQ_RVSERR) |
| return true; /* need retune */ |
| else if (val & SH_MOBILE_SDHI_SCC_RVSREQ_REQTAPUP) |
| new_tap++; |
| else if (val & SH_MOBILE_SDHI_SCC_RVSREQ_REQTAPDOWN) |
| new_tap--; |
| else |
| return false; |
| } |
| |
| priv->tap_set = (new_tap % priv->tap_num); |
| sd_scc_write32(host, priv, SH_MOBILE_SDHI_SCC_TAPSET, |
| priv->tap_set / (use_4tap ? 2 : 1)); |
| |
| return false; |
| } |
| |
| static bool renesas_sdhi_auto_correction(struct tmio_mmc_host *host) |
| { |
| struct renesas_sdhi *priv = host_to_priv(host); |
| |
| /* Check SCC error */ |
| if (sd_scc_read32(host, priv, SH_MOBILE_SDHI_SCC_RVSREQ) & |
| SH_MOBILE_SDHI_SCC_RVSREQ_RVSERR) { |
| sd_scc_write32(host, priv, SH_MOBILE_SDHI_SCC_RVSREQ, 0); |
| return true; |
| } |
| |
| return false; |
| } |
| |
| static bool renesas_sdhi_check_scc_error(struct tmio_mmc_host *host, |
| struct mmc_request *mrq) |
| { |
| struct renesas_sdhi *priv = host_to_priv(host); |
| bool use_4tap = priv->quirks && priv->quirks->hs400_4taps; |
| bool ret = false; |
| |
| /* |
| * Skip checking SCC errors when running on 4 taps in HS400 mode as |
| * any retuning would still result in the same 4 taps being used. |
| */ |
| if (!(host->mmc->ios.timing == MMC_TIMING_UHS_SDR104) && |
| !(host->mmc->ios.timing == MMC_TIMING_MMC_HS200) && |
| !(host->mmc->ios.timing == MMC_TIMING_MMC_HS400 && !use_4tap)) |
| return false; |
| |
| if (mmc_doing_tune(host->mmc)) |
| return false; |
| |
| if (((mrq->cmd->error == -ETIMEDOUT) || |
| (mrq->data && mrq->data->error == -ETIMEDOUT)) && |
| ((host->mmc->caps & MMC_CAP_NONREMOVABLE) || |
| (host->ops.get_cd && host->ops.get_cd(host->mmc)))) |
| ret |= true; |
| |
| if (sd_scc_read32(host, priv, SH_MOBILE_SDHI_SCC_RVSCNTL) & |
| SH_MOBILE_SDHI_SCC_RVSCNTL_RVSEN) |
| ret |= renesas_sdhi_auto_correction(host); |
| else |
| ret |= renesas_sdhi_manual_correction(host, use_4tap); |
| |
| return ret; |
| } |
| |
| static int renesas_sdhi_wait_idle(struct tmio_mmc_host *host, u32 bit) |
| { |
| int timeout = 1000; |
| /* CBSY is set when busy, SCLKDIVEN is cleared when busy */ |
| u32 wait_state = (bit == TMIO_STAT_CMD_BUSY ? TMIO_STAT_CMD_BUSY : 0); |
| |
| while (--timeout && (sd_ctrl_read16_and_16_as_32(host, CTL_STATUS) |
| & bit) == wait_state) |
| udelay(1); |
| |
| if (!timeout) { |
| dev_warn(&host->pdev->dev, "timeout waiting for SD bus idle\n"); |
| return -EBUSY; |
| } |
| |
| return 0; |
| } |
| |
| static int renesas_sdhi_write16_hook(struct tmio_mmc_host *host, int addr) |
| { |
| u32 bit = TMIO_STAT_SCLKDIVEN; |
| |
| switch (addr) { |
| case CTL_SD_CMD: |
| case CTL_STOP_INTERNAL_ACTION: |
| case CTL_XFER_BLK_COUNT: |
| case CTL_SD_XFER_LEN: |
| case CTL_SD_MEM_CARD_OPT: |
| case CTL_TRANSACTION_CTL: |
| case CTL_DMA_ENABLE: |
| case CTL_HOST_MODE: |
| if (host->pdata->flags & TMIO_MMC_HAVE_CBSY) |
| bit = TMIO_STAT_CMD_BUSY; |
| fallthrough; |
| case CTL_SD_CARD_CLK_CTL: |
| return renesas_sdhi_wait_idle(host, bit); |
| } |
| |
| return 0; |
| } |
| |
| static int renesas_sdhi_multi_io_quirk(struct mmc_card *card, |
| unsigned int direction, int blk_size) |
| { |
| /* |
| * In Renesas controllers, when performing a |
| * multiple block read of one or two blocks, |
| * depending on the timing with which the |
| * response register is read, the response |
| * value may not be read properly. |
| * Use single block read for this HW bug |
| */ |
| if ((direction == MMC_DATA_READ) && |
| blk_size == 2) |
| return 1; |
| |
| return blk_size; |
| } |
| |
| static void renesas_sdhi_fixup_request(struct tmio_mmc_host *host, struct mmc_request *mrq) |
| { |
| struct renesas_sdhi *priv = host_to_priv(host); |
| |
| if (priv->needs_adjust_hs400 && mrq->cmd->opcode == MMC_SEND_STATUS) |
| renesas_sdhi_adjust_hs400_mode_enable(host); |
| } |
| static void renesas_sdhi_enable_dma(struct tmio_mmc_host *host, bool enable) |
| { |
| /* Iff regs are 8 byte apart, sdbuf is 64 bit. Otherwise always 32. */ |
| int width = (host->bus_shift == 2) ? 64 : 32; |
| |
| sd_ctrl_write16(host, CTL_DMA_ENABLE, enable ? DMA_ENABLE_DMASDRW : 0); |
| renesas_sdhi_sdbuf_width(host, enable ? width : 16); |
| } |
| |
| static const struct renesas_sdhi_quirks sdhi_quirks_4tap_nohs400 = { |
| .hs400_disabled = true, |
| .hs400_4taps = true, |
| }; |
| |
| static const struct renesas_sdhi_quirks sdhi_quirks_4tap = { |
| .hs400_4taps = true, |
| .hs400_bad_taps = BIT(2) | BIT(3) | BIT(6) | BIT(7), |
| }; |
| |
| static const struct renesas_sdhi_quirks sdhi_quirks_nohs400 = { |
| .hs400_disabled = true, |
| }; |
| |
| static const struct renesas_sdhi_quirks sdhi_quirks_bad_taps1357 = { |
| .hs400_bad_taps = BIT(1) | BIT(3) | BIT(5) | BIT(7), |
| }; |
| |
| static const struct renesas_sdhi_quirks sdhi_quirks_bad_taps2367 = { |
| .hs400_bad_taps = BIT(2) | BIT(3) | BIT(6) | BIT(7), |
| }; |
| |
| static const struct renesas_sdhi_quirks sdhi_quirks_r8a7796_es13 = { |
| .hs400_4taps = true, |
| .hs400_bad_taps = BIT(2) | BIT(3) | BIT(6) | BIT(7), |
| .hs400_calib_table = r8a7796_es13_calib_table, |
| }; |
| |
| static const struct renesas_sdhi_quirks sdhi_quirks_r8a77965 = { |
| .hs400_bad_taps = BIT(2) | BIT(3) | BIT(6) | BIT(7), |
| .hs400_calib_table = r8a77965_calib_table, |
| }; |
| |
| static const struct renesas_sdhi_quirks sdhi_quirks_r8a77990 = { |
| .hs400_calib_table = r8a77990_calib_table, |
| }; |
| |
| /* |
| * Note for r8a7796 / r8a774a1: we can't distinguish ES1.1 and 1.2 as of now. |
| * So, we want to treat them equally and only have a match for ES1.2 to enforce |
| * this if there ever will be a way to distinguish ES1.2. |
| */ |
| static const struct soc_device_attribute sdhi_quirks_match[] = { |
| { .soc_id = "r8a774a1", .revision = "ES1.[012]", .data = &sdhi_quirks_4tap_nohs400 }, |
| { .soc_id = "r8a7795", .revision = "ES1.*", .data = &sdhi_quirks_4tap_nohs400 }, |
| { .soc_id = "r8a7795", .revision = "ES2.0", .data = &sdhi_quirks_4tap }, |
| { .soc_id = "r8a7795", .revision = "ES3.*", .data = &sdhi_quirks_bad_taps2367 }, |
| { .soc_id = "r8a7796", .revision = "ES1.[012]", .data = &sdhi_quirks_4tap_nohs400 }, |
| { .soc_id = "r8a7796", .revision = "ES1.*", .data = &sdhi_quirks_r8a7796_es13 }, |
| { .soc_id = "r8a77961", .data = &sdhi_quirks_bad_taps1357 }, |
| { .soc_id = "r8a77965", .data = &sdhi_quirks_r8a77965 }, |
| { .soc_id = "r8a77980", .data = &sdhi_quirks_nohs400 }, |
| { .soc_id = "r8a77990", .data = &sdhi_quirks_r8a77990 }, |
| { /* Sentinel. */ }, |
| }; |
| |
| int renesas_sdhi_probe(struct platform_device *pdev, |
| const struct tmio_mmc_dma_ops *dma_ops) |
| { |
| struct tmio_mmc_data *mmd = pdev->dev.platform_data; |
| const struct renesas_sdhi_quirks *quirks = NULL; |
| const struct renesas_sdhi_of_data *of_data; |
| const struct soc_device_attribute *attr; |
| struct tmio_mmc_data *mmc_data; |
| struct tmio_mmc_dma *dma_priv; |
| struct tmio_mmc_host *host; |
| struct renesas_sdhi *priv; |
| int num_irqs, irq, ret, i; |
| struct resource *res; |
| u16 ver; |
| |
| of_data = of_device_get_match_data(&pdev->dev); |
| |
| attr = soc_device_match(sdhi_quirks_match); |
| if (attr) |
| quirks = attr->data; |
| |
| res = platform_get_resource(pdev, IORESOURCE_MEM, 0); |
| if (!res) |
| return -EINVAL; |
| |
| priv = devm_kzalloc(&pdev->dev, sizeof(struct renesas_sdhi), |
| GFP_KERNEL); |
| if (!priv) |
| return -ENOMEM; |
| |
| priv->quirks = quirks; |
| mmc_data = &priv->mmc_data; |
| dma_priv = &priv->dma_priv; |
| |
| priv->clk = devm_clk_get(&pdev->dev, NULL); |
| if (IS_ERR(priv->clk)) { |
| ret = PTR_ERR(priv->clk); |
| dev_err(&pdev->dev, "cannot get clock: %d\n", ret); |
| return ret; |
| } |
| |
| /* |
| * Some controllers provide a 2nd clock just to run the internal card |
| * detection logic. Unfortunately, the existing driver architecture does |
| * not support a separation of clocks for runtime PM usage. When |
| * native hotplug is used, the tmio driver assumes that the core |
| * must continue to run for card detect to stay active, so we cannot |
| * disable it. |
| * Additionally, it is prohibited to supply a clock to the core but not |
| * to the card detect circuit. That leaves us with if separate clocks |
| * are presented, we must treat them both as virtually 1 clock. |
| */ |
| priv->clk_cd = devm_clk_get(&pdev->dev, "cd"); |
| if (IS_ERR(priv->clk_cd)) |
| priv->clk_cd = NULL; |
| |
| priv->pinctrl = devm_pinctrl_get(&pdev->dev); |
| if (!IS_ERR(priv->pinctrl)) { |
| priv->pins_default = pinctrl_lookup_state(priv->pinctrl, |
| PINCTRL_STATE_DEFAULT); |
| priv->pins_uhs = pinctrl_lookup_state(priv->pinctrl, |
| "state_uhs"); |
| } |
| |
| host = tmio_mmc_host_alloc(pdev, mmc_data); |
| if (IS_ERR(host)) |
| return PTR_ERR(host); |
| |
| if (of_data) { |
| mmc_data->flags |= of_data->tmio_flags; |
| mmc_data->ocr_mask = of_data->tmio_ocr_mask; |
| mmc_data->capabilities |= of_data->capabilities; |
| mmc_data->capabilities2 |= of_data->capabilities2; |
| mmc_data->dma_rx_offset = of_data->dma_rx_offset; |
| mmc_data->max_blk_count = of_data->max_blk_count; |
| mmc_data->max_segs = of_data->max_segs; |
| dma_priv->dma_buswidth = of_data->dma_buswidth; |
| host->bus_shift = of_data->bus_shift; |
| } |
| |
| host->write16_hook = renesas_sdhi_write16_hook; |
| host->clk_enable = renesas_sdhi_clk_enable; |
| host->clk_disable = renesas_sdhi_clk_disable; |
| host->set_clock = renesas_sdhi_set_clock; |
| host->multi_io_quirk = renesas_sdhi_multi_io_quirk; |
| host->dma_ops = dma_ops; |
| |
| if (quirks && quirks->hs400_disabled) |
| host->mmc->caps2 &= ~(MMC_CAP2_HS400 | MMC_CAP2_HS400_ES); |
| |
| /* For some SoC, we disable internal WP. GPIO may override this */ |
| if (mmc_can_gpio_ro(host->mmc)) |
| mmc_data->capabilities2 &= ~MMC_CAP2_NO_WRITE_PROTECT; |
| |
| /* SDR speeds are only available on Gen2+ */ |
| if (mmc_data->flags & TMIO_MMC_MIN_RCAR2) { |
| /* card_busy caused issues on r8a73a4 (pre-Gen2) CD-less SDHI */ |
| host->ops.card_busy = renesas_sdhi_card_busy; |
| host->ops.start_signal_voltage_switch = |
| renesas_sdhi_start_signal_voltage_switch; |
| host->sdcard_irq_setbit_mask = TMIO_STAT_ALWAYS_SET_27; |
| host->sdcard_irq_mask_all = TMIO_MASK_ALL_RCAR2; |
| host->reset = renesas_sdhi_reset; |
| } |
| |
| /* Orginally registers were 16 bit apart, could be 32 or 64 nowadays */ |
| if (!host->bus_shift && resource_size(res) > 0x100) /* old way to determine the shift */ |
| host->bus_shift = 1; |
| |
| if (mmd) |
| *mmc_data = *mmd; |
| |
| dma_priv->filter = shdma_chan_filter; |
| dma_priv->enable = renesas_sdhi_enable_dma; |
| |
| mmc_data->alignment_shift = 1; /* 2-byte alignment */ |
| mmc_data->capabilities |= MMC_CAP_MMC_HIGHSPEED; |
| |
| /* |
| * All SDHI blocks support 2-byte and larger block sizes in 4-bit |
| * bus width mode. |
| */ |
| mmc_data->flags |= TMIO_MMC_BLKSZ_2BYTES; |
| |
| /* |
| * All SDHI blocks support SDIO IRQ signalling. |
| */ |
| mmc_data->flags |= TMIO_MMC_SDIO_IRQ; |
| |
| /* All SDHI have CMD12 control bit */ |
| mmc_data->flags |= TMIO_MMC_HAVE_CMD12_CTRL; |
| |
| /* All SDHI have SDIO status bits which must be 1 */ |
| mmc_data->flags |= TMIO_MMC_SDIO_STATUS_SETBITS; |
| |
| /* All SDHI support HW busy detection */ |
| mmc_data->flags |= TMIO_MMC_USE_BUSY_TIMEOUT; |
| |
| dev_pm_domain_start(&pdev->dev); |
| |
| ret = renesas_sdhi_clk_enable(host); |
| if (ret) |
| goto efree; |
| |
| priv->rstc = devm_reset_control_get_optional_exclusive(&pdev->dev, NULL); |
| if (IS_ERR(priv->rstc)) |
| return PTR_ERR(priv->rstc); |
| |
| ver = sd_ctrl_read16(host, CTL_VERSION); |
| /* GEN2_SDR104 is first known SDHI to use 32bit block count */ |
| if (ver < SDHI_VER_GEN2_SDR104 && mmc_data->max_blk_count > U16_MAX) |
| mmc_data->max_blk_count = U16_MAX; |
| |
| /* One Gen2 SDHI incarnation does NOT have a CBSY bit */ |
| if (ver == SDHI_VER_GEN2_SDR50) |
| mmc_data->flags &= ~TMIO_MMC_HAVE_CBSY; |
| |
| if (ver == SDHI_VER_GEN3_SDMMC && quirks && quirks->hs400_calib_table) { |
| host->fixup_request = renesas_sdhi_fixup_request; |
| priv->adjust_hs400_calib_table = *( |
| res->start == SDHI_GEN3_MMC0_ADDR ? |
| quirks->hs400_calib_table : |
| quirks->hs400_calib_table + 1); |
| } |
| |
| /* these have an EXTOP bit */ |
| if (ver >= SDHI_VER_GEN3_SD) |
| host->get_timeout_cycles = renesas_sdhi_gen3_get_cycles; |
| |
| /* Enable tuning iff we have an SCC and a supported mode */ |
| if (of_data && of_data->scc_offset && |
| (host->mmc->caps & MMC_CAP_UHS_SDR104 || |
| host->mmc->caps2 & (MMC_CAP2_HS200_1_8V_SDR | |
| MMC_CAP2_HS400_1_8V))) { |
| const struct renesas_sdhi_scc *taps = of_data->taps; |
| bool use_4tap = priv->quirks && priv->quirks->hs400_4taps; |
| bool hit = false; |
| |
| for (i = 0; i < of_data->taps_num; i++) { |
| if (taps[i].clk_rate == 0 || |
| taps[i].clk_rate == host->mmc->f_max) { |
| priv->scc_tappos = taps->tap; |
| priv->scc_tappos_hs400 = use_4tap ? |
| taps->tap_hs400_4tap : |
| taps->tap; |
| hit = true; |
| break; |
| } |
| } |
| |
| if (!hit) |
| dev_warn(&host->pdev->dev, "Unknown clock rate for tuning\n"); |
| |
| priv->scc_ctl = host->ctl + of_data->scc_offset; |
| host->check_retune = renesas_sdhi_check_scc_error; |
| host->ops.execute_tuning = renesas_sdhi_execute_tuning; |
| host->ops.prepare_hs400_tuning = renesas_sdhi_prepare_hs400_tuning; |
| host->ops.hs400_downgrade = renesas_sdhi_disable_scc; |
| host->ops.hs400_complete = renesas_sdhi_hs400_complete; |
| } |
| |
| ret = tmio_mmc_host_probe(host); |
| if (ret < 0) |
| goto edisclk; |
| |
| num_irqs = platform_irq_count(pdev); |
| if (num_irqs < 0) { |
| ret = num_irqs; |
| goto eirq; |
| } |
| |
| /* There must be at least one IRQ source */ |
| if (!num_irqs) { |
| ret = -ENXIO; |
| goto eirq; |
| } |
| |
| for (i = 0; i < num_irqs; i++) { |
| irq = platform_get_irq(pdev, i); |
| if (irq < 0) { |
| ret = irq; |
| goto eirq; |
| } |
| |
| ret = devm_request_irq(&pdev->dev, irq, tmio_mmc_irq, 0, |
| dev_name(&pdev->dev), host); |
| if (ret) |
| goto eirq; |
| } |
| |
| dev_info(&pdev->dev, "%s base at %pa, max clock rate %u MHz\n", |
| mmc_hostname(host->mmc), &res->start, host->mmc->f_max / 1000000); |
| |
| return ret; |
| |
| eirq: |
| tmio_mmc_host_remove(host); |
| edisclk: |
| renesas_sdhi_clk_disable(host); |
| efree: |
| tmio_mmc_host_free(host); |
| |
| return ret; |
| } |
| EXPORT_SYMBOL_GPL(renesas_sdhi_probe); |
| |
| int renesas_sdhi_remove(struct platform_device *pdev) |
| { |
| struct tmio_mmc_host *host = platform_get_drvdata(pdev); |
| |
| tmio_mmc_host_remove(host); |
| renesas_sdhi_clk_disable(host); |
| tmio_mmc_host_free(host); |
| |
| return 0; |
| } |
| EXPORT_SYMBOL_GPL(renesas_sdhi_remove); |
| |
| MODULE_LICENSE("GPL v2"); |