Google Git
Sign in
android-kvm / linux / 451ed8058c69a3fee29fa9e2967a4e22a221fe75 / . / drivers / power / supply / smb347-charger.c
blob: 1511f71f937c73ad125001fb3016f529acfa05cb [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0-only
/*
* Summit Microelectronics SMB347 Battery Charger Driver
*
* Copyright (C) 2011, Intel Corporation
*
* Authors: Bruce E. Robertson <bruce.e.robertson@intel.com>
* Mika Westerberg <mika.westerberg@linux.intel.com>
*/
#include <linux/delay.h>
#include <linux/err.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/i2c.h>
#include <linux/power_supply.h>
#include <linux/property.h>
#include <linux/regmap.h>
#include <linux/regulator/driver.h>
#include <dt-bindings/power/summit,smb347-charger.h>
/* Use the default compensation method */
#define SMB3XX_SOFT_TEMP_COMPENSATE_DEFAULT -1
/* Use default factory programmed value for hard/soft temperature limit */
#define SMB3XX_TEMP_USE_DEFAULT -273
/*
* Configuration registers. These are mirrored to volatile RAM and can be
* written once %CMD_A_ALLOW_WRITE is set in %CMD_A register. They will be
* reloaded from non-volatile registers after POR.
*/
#define CFG_CHARGE_CURRENT 0x00
#define CFG_CHARGE_CURRENT_FCC_MASK 0xe0
#define CFG_CHARGE_CURRENT_FCC_SHIFT 5
#define CFG_CHARGE_CURRENT_PCC_MASK 0x18
#define CFG_CHARGE_CURRENT_PCC_SHIFT 3
#define CFG_CHARGE_CURRENT_TC_MASK 0x07
#define CFG_CURRENT_LIMIT 0x01
#define CFG_CURRENT_LIMIT_DC_MASK 0xf0
#define CFG_CURRENT_LIMIT_DC_SHIFT 4
#define CFG_CURRENT_LIMIT_USB_MASK 0x0f
#define CFG_FLOAT_VOLTAGE 0x03
#define CFG_FLOAT_VOLTAGE_FLOAT_MASK 0x3f
#define CFG_FLOAT_VOLTAGE_THRESHOLD_MASK 0xc0
#define CFG_FLOAT_VOLTAGE_THRESHOLD_SHIFT 6
#define CFG_STAT 0x05
#define CFG_STAT_DISABLED BIT(5)
#define CFG_STAT_ACTIVE_HIGH BIT(7)
#define CFG_PIN 0x06
#define CFG_PIN_EN_CTRL_MASK 0x60
#define CFG_PIN_EN_CTRL_ACTIVE_HIGH 0x40
#define CFG_PIN_EN_CTRL_ACTIVE_LOW 0x60
#define CFG_PIN_EN_APSD_IRQ BIT(1)
#define CFG_PIN_EN_CHARGER_ERROR BIT(2)
#define CFG_PIN_EN_CTRL BIT(4)
#define CFG_THERM 0x07
#define CFG_THERM_SOFT_HOT_COMPENSATION_MASK 0x03
#define CFG_THERM_SOFT_HOT_COMPENSATION_SHIFT 0
#define CFG_THERM_SOFT_COLD_COMPENSATION_MASK 0x0c
#define CFG_THERM_SOFT_COLD_COMPENSATION_SHIFT 2
#define CFG_THERM_MONITOR_DISABLED BIT(4)
#define CFG_SYSOK 0x08
#define CFG_SYSOK_INOK_ACTIVE_HIGH BIT(0)
#define CFG_SYSOK_SUSPEND_HARD_LIMIT_DISABLED BIT(2)
#define CFG_OTHER 0x09
#define CFG_OTHER_RID_MASK 0xc0
#define CFG_OTHER_RID_ENABLED_AUTO_OTG 0xc0
#define CFG_OTG 0x0a
#define CFG_OTG_TEMP_THRESHOLD_MASK 0x30
#define CFG_OTG_CURRENT_LIMIT_250mA BIT(2)
#define CFG_OTG_CURRENT_LIMIT_750mA BIT(3)
#define CFG_OTG_TEMP_THRESHOLD_SHIFT 4
#define CFG_OTG_CC_COMPENSATION_MASK 0xc0
#define CFG_OTG_CC_COMPENSATION_SHIFT 6
#define CFG_TEMP_LIMIT 0x0b
#define CFG_TEMP_LIMIT_SOFT_HOT_MASK 0x03
#define CFG_TEMP_LIMIT_SOFT_HOT_SHIFT 0
#define CFG_TEMP_LIMIT_SOFT_COLD_MASK 0x0c
#define CFG_TEMP_LIMIT_SOFT_COLD_SHIFT 2
#define CFG_TEMP_LIMIT_HARD_HOT_MASK 0x30
#define CFG_TEMP_LIMIT_HARD_HOT_SHIFT 4
#define CFG_TEMP_LIMIT_HARD_COLD_MASK 0xc0
#define CFG_TEMP_LIMIT_HARD_COLD_SHIFT 6
#define CFG_FAULT_IRQ 0x0c
#define CFG_FAULT_IRQ_DCIN_UV BIT(2)
#define CFG_STATUS_IRQ 0x0d
#define CFG_STATUS_IRQ_TERMINATION_OR_TAPER BIT(4)
#define CFG_STATUS_IRQ_CHARGE_TIMEOUT BIT(7)
#define CFG_ADDRESS 0x0e
/* Command registers */
#define CMD_A 0x30
#define CMD_A_CHG_ENABLED BIT(1)
#define CMD_A_SUSPEND_ENABLED BIT(2)
#define CMD_A_OTG_ENABLED BIT(4)
#define CMD_A_ALLOW_WRITE BIT(7)
#define CMD_B 0x31
#define CMD_C 0x33
/* Interrupt Status registers */
#define IRQSTAT_A 0x35
#define IRQSTAT_C 0x37
#define IRQSTAT_C_TERMINATION_STAT BIT(0)
#define IRQSTAT_C_TERMINATION_IRQ BIT(1)
#define IRQSTAT_C_TAPER_IRQ BIT(3)
#define IRQSTAT_D 0x38
#define IRQSTAT_D_CHARGE_TIMEOUT_STAT BIT(2)
#define IRQSTAT_D_CHARGE_TIMEOUT_IRQ BIT(3)
#define IRQSTAT_E 0x39
#define IRQSTAT_E_USBIN_UV_STAT BIT(0)
#define IRQSTAT_E_USBIN_UV_IRQ BIT(1)
#define IRQSTAT_E_DCIN_UV_STAT BIT(4)
#define IRQSTAT_E_DCIN_UV_IRQ BIT(5)
#define IRQSTAT_F 0x3a
/* Status registers */
#define STAT_A 0x3b
#define STAT_A_FLOAT_VOLTAGE_MASK 0x3f
#define STAT_B 0x3c
#define STAT_C 0x3d
#define STAT_C_CHG_ENABLED BIT(0)
#define STAT_C_HOLDOFF_STAT BIT(3)
#define STAT_C_CHG_MASK 0x06
#define STAT_C_CHG_SHIFT 1
#define STAT_C_CHG_TERM BIT(5)
#define STAT_C_CHARGER_ERROR BIT(6)
#define STAT_E 0x3f
#define SMB347_MAX_REGISTER 0x3f
/**
* struct smb347_charger - smb347 charger instance
* @dev: pointer to device
* @regmap: pointer to driver regmap
* @mains: power_supply instance for AC/DC power
* @usb: power_supply instance for USB power
* @usb_rdev: USB VBUS regulator device
* @id: SMB charger ID
* @mains_online: is AC/DC input connected
* @usb_online: is USB input connected
* @irq_unsupported: is interrupt unsupported by SMB hardware
* @usb_vbus_enabled: is USB VBUS powered by SMB charger
* @max_charge_current: maximum current (in uA) the battery can be charged
* @max_charge_voltage: maximum voltage (in uV) the battery can be charged
* @pre_charge_current: current (in uA) to use in pre-charging phase
* @termination_current: current (in uA) used to determine when the
* charging cycle terminates
* @pre_to_fast_voltage: voltage (in uV) treshold used for transitioning to
* pre-charge to fast charge mode
* @mains_current_limit: maximum input current drawn from AC/DC input (in uA)
* @usb_hc_current_limit: maximum input high current (in uA) drawn from USB
* input
* @chip_temp_threshold: die temperature where device starts limiting charge
* current [%100 - %130] (in degree C)
* @soft_cold_temp_limit: soft cold temperature limit [%0 - %15] (in degree C),
* granularity is 5 deg C.
* @soft_hot_temp_limit: soft hot temperature limit [%40 - %55] (in degree C),
* granularity is 5 deg C.
* @hard_cold_temp_limit: hard cold temperature limit [%-5 - %10] (in degree C),
* granularity is 5 deg C.
* @hard_hot_temp_limit: hard hot temperature limit [%50 - %65] (in degree C),
* granularity is 5 deg C.
* @suspend_on_hard_temp_limit: suspend charging when hard limit is hit
* @soft_temp_limit_compensation: compensation method when soft temperature
* limit is hit
* @charge_current_compensation: current (in uA) for charging compensation
* current when temperature hits soft limits
* @use_mains: AC/DC input can be used
* @use_usb: USB input can be used
* @use_usb_otg: USB OTG output can be used (not implemented yet)
* @enable_control: how charging enable/disable is controlled
* (driver/pin controls)
* @inok_polarity: polarity of INOK signal which denotes presence of external
* power supply
*
* @use_main, @use_usb, and @use_usb_otg are means to enable/disable
* hardware support for these. This is useful when we want to have for
* example OTG charging controlled via OTG transceiver driver and not by
* the SMB347 hardware.
*
* Hard and soft temperature limit values are given as described in the
* device data sheet and assuming NTC beta value is %3750. Even if this is
* not the case, these values should be used. They can be mapped to the
* corresponding NTC beta values with the help of table %2 in the data
* sheet. So for example if NTC beta is %3375 and we want to program hard
* hot limit to be %53 deg C, @hard_hot_temp_limit should be set to %50.
*
* If zero value is given in any of the current and voltage values, the
* factory programmed default will be used. For soft/hard temperature
* values, pass in %SMB3XX_TEMP_USE_DEFAULT instead.
*/
struct smb347_charger {
struct device *dev;
struct regmap *regmap;
struct power_supply *mains;
struct power_supply *usb;
struct regulator_dev *usb_rdev;
unsigned int id;
bool mains_online;
bool usb_online;
bool irq_unsupported;
bool usb_vbus_enabled;
unsigned int max_charge_current;
unsigned int max_charge_voltage;
unsigned int pre_charge_current;
unsigned int termination_current;
unsigned int pre_to_fast_voltage;
unsigned int mains_current_limit;
unsigned int usb_hc_current_limit;
unsigned int chip_temp_threshold;
int soft_cold_temp_limit;
int soft_hot_temp_limit;
int hard_cold_temp_limit;
int hard_hot_temp_limit;
bool suspend_on_hard_temp_limit;
unsigned int soft_temp_limit_compensation;
unsigned int charge_current_compensation;
bool use_mains;
bool use_usb;
bool use_usb_otg;
unsigned int enable_control;
unsigned int inok_polarity;
};
enum smb_charger_chipid {
SMB345,
SMB347,
SMB358,
NUM_CHIP_TYPES,
};
/* Fast charge current in uA */
static const unsigned int fcc_tbl[NUM_CHIP_TYPES][8] = {
[SMB345] = { 200000, 450000, 600000, 900000,
1300000, 1500000, 1800000, 2000000 },
[SMB347] = { 700000, 900000, 1200000, 1500000,
1800000, 2000000, 2200000, 2500000 },
[SMB358] = { 200000, 450000, 600000, 900000,
1300000, 1500000, 1800000, 2000000 },
};
/* Pre-charge current in uA */
static const unsigned int pcc_tbl[NUM_CHIP_TYPES][4] = {
[SMB345] = { 150000, 250000, 350000, 450000 },
[SMB347] = { 100000, 150000, 200000, 250000 },
[SMB358] = { 150000, 250000, 350000, 450000 },
};
/* Termination current in uA */
static const unsigned int tc_tbl[NUM_CHIP_TYPES][8] = {
[SMB345] = { 30000, 40000, 60000, 80000,
100000, 125000, 150000, 200000 },
[SMB347] = { 37500, 50000, 100000, 150000,
200000, 250000, 500000, 600000 },
[SMB358] = { 30000, 40000, 60000, 80000,
100000, 125000, 150000, 200000 },
};
/* Input current limit in uA */
static const unsigned int icl_tbl[NUM_CHIP_TYPES][10] = {
[SMB345] = { 300000, 500000, 700000, 1000000, 1500000,
1800000, 2000000, 2000000, 2000000, 2000000 },
[SMB347] = { 300000, 500000, 700000, 900000, 1200000,
1500000, 1800000, 2000000, 2200000, 2500000 },
[SMB358] = { 300000, 500000, 700000, 1000000, 1500000,
1800000, 2000000, 2000000, 2000000, 2000000 },
};
/* Charge current compensation in uA */
static const unsigned int ccc_tbl[NUM_CHIP_TYPES][4] = {
[SMB345] = { 200000, 450000, 600000, 900000 },
[SMB347] = { 250000, 700000, 900000, 1200000 },
[SMB358] = { 200000, 450000, 600000, 900000 },
};
/* Convert register value to current using lookup table */
static int hw_to_current(const unsigned int *tbl, size_t size, unsigned int val)
{
if (val >= size)
return -EINVAL;
return tbl[val];
}
/* Convert current to register value using lookup table */
static int current_to_hw(const unsigned int *tbl, size_t size, unsigned int val)
{
size_t i;
for (i = 0; i < size; i++)
if (val < tbl[i])
break;
return i > 0 ? i - 1 : -EINVAL;
}
/**
* smb347_update_ps_status - refreshes the power source status
* @smb: pointer to smb347 charger instance
*
* Function checks whether any power source is connected to the charger and
* updates internal state accordingly. If there is a change to previous state
* function returns %1, otherwise %0 and negative errno in case of errror.
*/
static int smb347_update_ps_status(struct smb347_charger *smb)
{
bool usb = false;
bool dc = false;
unsigned int val;
int ret;
ret = regmap_read(smb->regmap, IRQSTAT_E, &val);
if (ret < 0)
return ret;
/*
* Dc and usb are set depending on whether they are enabled in
* platform data _and_ whether corresponding undervoltage is set.
*/
if (smb->use_mains)
dc = !(val & IRQSTAT_E_DCIN_UV_STAT);
if (smb->use_usb)
usb = !(val & IRQSTAT_E_USBIN_UV_STAT);
ret = smb->mains_online != dc || smb->usb_online != usb;
smb->mains_online = dc;
smb->usb_online = usb;
return ret;
}
/*
* smb347_is_ps_online - returns whether input power source is connected
* @smb: pointer to smb347 charger instance
*
* Returns %true if input power source is connected. Note that this is
* dependent on what platform has configured for usable power sources. For
* example if USB is disabled, this will return %false even if the USB cable
* is connected.
*/
static bool smb347_is_ps_online(struct smb347_charger *smb)
{
return smb->usb_online || smb->mains_online;
}
/**
* smb347_charging_status - returns status of charging
* @smb: pointer to smb347 charger instance
*
* Function returns charging status. %0 means no charging is in progress,
* %1 means pre-charging, %2 fast-charging and %3 taper-charging.
*/
static int smb347_charging_status(struct smb347_charger *smb)
{
unsigned int val;
int ret;
if (!smb347_is_ps_online(smb))
return 0;
ret = regmap_read(smb->regmap, STAT_C, &val);
if (ret < 0)
return 0;
return (val & STAT_C_CHG_MASK) >> STAT_C_CHG_SHIFT;
}
static int smb347_charging_set(struct smb347_charger *smb, bool enable)
{
if (smb->enable_control != SMB3XX_CHG_ENABLE_SW) {
dev_dbg(smb->dev, "charging enable/disable in SW disabled\n");
return 0;
}
if (enable && smb->usb_vbus_enabled) {
dev_dbg(smb->dev, "charging not enabled because USB is in host mode\n");
return 0;
}
return regmap_update_bits(smb->regmap, CMD_A, CMD_A_CHG_ENABLED,
enable ? CMD_A_CHG_ENABLED : 0);
}
static inline int smb347_charging_enable(struct smb347_charger *smb)
{
return smb347_charging_set(smb, true);
}
static inline int smb347_charging_disable(struct smb347_charger *smb)
{
return smb347_charging_set(smb, false);
}
static int smb347_start_stop_charging(struct smb347_charger *smb)
{
int ret;
/*
* Depending on whether valid power source is connected or not, we
* disable or enable the charging. We do it manually because it
* depends on how the platform has configured the valid inputs.
*/
if (smb347_is_ps_online(smb)) {
ret = smb347_charging_enable(smb);
if (ret < 0)
dev_err(smb->dev, "failed to enable charging\n");
} else {
ret = smb347_charging_disable(smb);
if (ret < 0)
dev_err(smb->dev, "failed to disable charging\n");
}
return ret;
}
static int smb347_set_charge_current(struct smb347_charger *smb)
{
unsigned int id = smb->id;
int ret;
if (smb->max_charge_current) {
ret = current_to_hw(fcc_tbl[id], ARRAY_SIZE(fcc_tbl[id]),
smb->max_charge_current);
if (ret < 0)
return ret;
ret = regmap_update_bits(smb->regmap, CFG_CHARGE_CURRENT,
CFG_CHARGE_CURRENT_FCC_MASK,
ret << CFG_CHARGE_CURRENT_FCC_SHIFT);
if (ret < 0)
return ret;
}
if (smb->pre_charge_current) {
ret = current_to_hw(pcc_tbl[id], ARRAY_SIZE(pcc_tbl[id]),
smb->pre_charge_current);
if (ret < 0)
return ret;
ret = regmap_update_bits(smb->regmap, CFG_CHARGE_CURRENT,
CFG_CHARGE_CURRENT_PCC_MASK,
ret << CFG_CHARGE_CURRENT_PCC_SHIFT);
if (ret < 0)
return ret;
}
if (smb->termination_current) {
ret = current_to_hw(tc_tbl[id], ARRAY_SIZE(tc_tbl[id]),
smb->termination_current);
if (ret < 0)
return ret;
ret = regmap_update_bits(smb->regmap, CFG_CHARGE_CURRENT,
CFG_CHARGE_CURRENT_TC_MASK, ret);
if (ret < 0)
return ret;
}
return 0;
}
static int smb347_set_current_limits(struct smb347_charger *smb)
{
unsigned int id = smb->id;
int ret;
if (smb->mains_current_limit) {
ret = current_to_hw(icl_tbl[id], ARRAY_SIZE(icl_tbl[id]),
smb->mains_current_limit);
if (ret < 0)
return ret;
ret = regmap_update_bits(smb->regmap, CFG_CURRENT_LIMIT,
CFG_CURRENT_LIMIT_DC_MASK,
ret << CFG_CURRENT_LIMIT_DC_SHIFT);
if (ret < 0)
return ret;
}
if (smb->usb_hc_current_limit) {
ret = current_to_hw(icl_tbl[id], ARRAY_SIZE(icl_tbl[id]),
smb->usb_hc_current_limit);
if (ret < 0)
return ret;
ret = regmap_update_bits(smb->regmap, CFG_CURRENT_LIMIT,
CFG_CURRENT_LIMIT_USB_MASK, ret);
if (ret < 0)
return ret;
}
return 0;
}
static int smb347_set_voltage_limits(struct smb347_charger *smb)
{
int ret;
if (smb->pre_to_fast_voltage) {
ret = smb->pre_to_fast_voltage;
/* uV */
ret = clamp_val(ret, 2400000, 3000000) - 2400000;
ret /= 200000;
ret = regmap_update_bits(smb->regmap, CFG_FLOAT_VOLTAGE,
CFG_FLOAT_VOLTAGE_THRESHOLD_MASK,
ret << CFG_FLOAT_VOLTAGE_THRESHOLD_SHIFT);
if (ret < 0)
return ret;
}
if (smb->max_charge_voltage) {
ret = smb->max_charge_voltage;
/* uV */
ret = clamp_val(ret, 3500000, 4500000) - 3500000;
ret /= 20000;
ret = regmap_update_bits(smb->regmap, CFG_FLOAT_VOLTAGE,
CFG_FLOAT_VOLTAGE_FLOAT_MASK, ret);
if (ret < 0)
return ret;
}
return 0;
}
static int smb347_set_temp_limits(struct smb347_charger *smb)
{
unsigned int id = smb->id;
bool enable_therm_monitor = false;
int ret = 0;
int val;
if (smb->chip_temp_threshold) {
val = smb->chip_temp_threshold;
/* degree C */
val = clamp_val(val, 100, 130) - 100;
val /= 10;
ret = regmap_update_bits(smb->regmap, CFG_OTG,
CFG_OTG_TEMP_THRESHOLD_MASK,
val << CFG_OTG_TEMP_THRESHOLD_SHIFT);
if (ret < 0)
return ret;
}
if (smb->soft_cold_temp_limit != SMB3XX_TEMP_USE_DEFAULT) {
val = smb->soft_cold_temp_limit;
val = clamp_val(val, 0, 15);
val /= 5;
/* this goes from higher to lower so invert the value */
val = ~val & 0x3;
ret = regmap_update_bits(smb->regmap, CFG_TEMP_LIMIT,
CFG_TEMP_LIMIT_SOFT_COLD_MASK,
val << CFG_TEMP_LIMIT_SOFT_COLD_SHIFT);
if (ret < 0)
return ret;
enable_therm_monitor = true;
}
if (smb->soft_hot_temp_limit != SMB3XX_TEMP_USE_DEFAULT) {
val = smb->soft_hot_temp_limit;
val = clamp_val(val, 40, 55) - 40;
val /= 5;
ret = regmap_update_bits(smb->regmap, CFG_TEMP_LIMIT,
CFG_TEMP_LIMIT_SOFT_HOT_MASK,
val << CFG_TEMP_LIMIT_SOFT_HOT_SHIFT);
if (ret < 0)
return ret;
enable_therm_monitor = true;
}
if (smb->hard_cold_temp_limit != SMB3XX_TEMP_USE_DEFAULT) {
val = smb->hard_cold_temp_limit;
val = clamp_val(val, -5, 10) + 5;
val /= 5;
/* this goes from higher to lower so invert the value */
val = ~val & 0x3;
ret = regmap_update_bits(smb->regmap, CFG_TEMP_LIMIT,
CFG_TEMP_LIMIT_HARD_COLD_MASK,
val << CFG_TEMP_LIMIT_HARD_COLD_SHIFT);
if (ret < 0)
return ret;
enable_therm_monitor = true;
}
if (smb->hard_hot_temp_limit != SMB3XX_TEMP_USE_DEFAULT) {
val = smb->hard_hot_temp_limit;
val = clamp_val(val, 50, 65) - 50;
val /= 5;
ret = regmap_update_bits(smb->regmap, CFG_TEMP_LIMIT,
CFG_TEMP_LIMIT_HARD_HOT_MASK,
val << CFG_TEMP_LIMIT_HARD_HOT_SHIFT);
if (ret < 0)
return ret;
enable_therm_monitor = true;
}
/*
* If any of the temperature limits are set, we also enable the
* thermistor monitoring.
*
* When soft limits are hit, the device will start to compensate
* current and/or voltage depending on the configuration.
*
* When hard limit is hit, the device will suspend charging
* depending on the configuration.
*/
if (enable_therm_monitor) {
ret = regmap_update_bits(smb->regmap, CFG_THERM,
CFG_THERM_MONITOR_DISABLED, 0);
if (ret < 0)
return ret;
}
if (smb->suspend_on_hard_temp_limit) {
ret = regmap_update_bits(smb->regmap, CFG_SYSOK,
CFG_SYSOK_SUSPEND_HARD_LIMIT_DISABLED, 0);
if (ret < 0)
return ret;
}
if (smb->soft_temp_limit_compensation !=
SMB3XX_SOFT_TEMP_COMPENSATE_DEFAULT) {
val = smb->soft_temp_limit_compensation & 0x3;
ret = regmap_update_bits(smb->regmap, CFG_THERM,
CFG_THERM_SOFT_HOT_COMPENSATION_MASK,
val << CFG_THERM_SOFT_HOT_COMPENSATION_SHIFT);
if (ret < 0)
return ret;
ret = regmap_update_bits(smb->regmap, CFG_THERM,
CFG_THERM_SOFT_COLD_COMPENSATION_MASK,
val << CFG_THERM_SOFT_COLD_COMPENSATION_SHIFT);
if (ret < 0)
return ret;
}
if (smb->charge_current_compensation) {
val = current_to_hw(ccc_tbl[id], ARRAY_SIZE(ccc_tbl[id]),
smb->charge_current_compensation);
if (val < 0)
return val;
ret = regmap_update_bits(smb->regmap, CFG_OTG,
CFG_OTG_CC_COMPENSATION_MASK,
(val & 0x3) << CFG_OTG_CC_COMPENSATION_SHIFT);
if (ret < 0)
return ret;
}
return ret;
}
/*
* smb347_set_writable - enables/disables writing to non-volatile registers
* @smb: pointer to smb347 charger instance
*
* You can enable/disable writing to the non-volatile configuration
* registers by calling this function.
*
* Returns %0 on success and negative errno in case of failure.
*/
static int smb347_set_writable(struct smb347_charger *smb, bool writable,
bool irq_toggle)
{
struct i2c_client *client = to_i2c_client(smb->dev);
int ret;
if (writable && irq_toggle && !smb->irq_unsupported)
disable_irq(client->irq);
ret = regmap_update_bits(smb->regmap, CMD_A, CMD_A_ALLOW_WRITE,
writable ? CMD_A_ALLOW_WRITE : 0);
if ((!writable || ret) && irq_toggle && !smb->irq_unsupported)
enable_irq(client->irq);
return ret;
}
static int smb347_hw_init(struct smb347_charger *smb)
{
unsigned int val;
int ret;
ret = smb347_set_writable(smb, true, false);
if (ret < 0)
return ret;
/*
* Program the platform specific configuration values to the device
* first.
*/
ret = smb347_set_charge_current(smb);
if (ret < 0)
goto fail;
ret = smb347_set_current_limits(smb);
if (ret < 0)
goto fail;
ret = smb347_set_voltage_limits(smb);
if (ret < 0)
goto fail;
ret = smb347_set_temp_limits(smb);
if (ret < 0)
goto fail;
/* If USB charging is disabled we put the USB in suspend mode */
if (!smb->use_usb) {
ret = regmap_update_bits(smb->regmap, CMD_A,
CMD_A_SUSPEND_ENABLED,
CMD_A_SUSPEND_ENABLED);
if (ret < 0)
goto fail;
}
/*
* If configured by platform data, we enable hardware Auto-OTG
* support for driving VBUS. Otherwise we disable it.
*/
ret = regmap_update_bits(smb->regmap, CFG_OTHER, CFG_OTHER_RID_MASK,
smb->use_usb_otg ? CFG_OTHER_RID_ENABLED_AUTO_OTG : 0);
if (ret < 0)
goto fail;
/* Activate pin control, making it writable. */
switch (smb->enable_control) {
case SMB3XX_CHG_ENABLE_PIN_ACTIVE_LOW:
case SMB3XX_CHG_ENABLE_PIN_ACTIVE_HIGH:
ret = regmap_set_bits(smb->regmap, CFG_PIN, CFG_PIN_EN_CTRL);
if (ret < 0)
goto fail;
}
/*
* Make the charging functionality controllable by a write to the
* command register unless pin control is specified in the platform
* data.
*/
switch (smb->enable_control) {
case SMB3XX_CHG_ENABLE_PIN_ACTIVE_LOW:
val = CFG_PIN_EN_CTRL_ACTIVE_LOW;
break;
case SMB3XX_CHG_ENABLE_PIN_ACTIVE_HIGH:
val = CFG_PIN_EN_CTRL_ACTIVE_HIGH;
break;
default:
val = 0;
break;
}
ret = regmap_update_bits(smb->regmap, CFG_PIN, CFG_PIN_EN_CTRL_MASK,
val);
if (ret < 0)
goto fail;
/* Disable Automatic Power Source Detection (APSD) interrupt. */
ret = regmap_update_bits(smb->regmap, CFG_PIN, CFG_PIN_EN_APSD_IRQ, 0);
if (ret < 0)
goto fail;
ret = smb347_update_ps_status(smb);
if (ret < 0)
goto fail;
ret = smb347_start_stop_charging(smb);
fail:
smb347_set_writable(smb, false, false);
return ret;
}
static irqreturn_t smb347_interrupt(int irq, void *data)
{
struct smb347_charger *smb = data;
unsigned int stat_c, irqstat_c, irqstat_d, irqstat_e;
bool handled = false;
int ret;
/* SMB347 it needs at least 20ms for setting IRQSTAT_E_*IN_UV_IRQ */
usleep_range(25000, 35000);
ret = regmap_read(smb->regmap, STAT_C, &stat_c);
if (ret < 0) {
dev_warn(smb->dev, "reading STAT_C failed\n");
return IRQ_NONE;
}
ret = regmap_read(smb->regmap, IRQSTAT_C, &irqstat_c);
if (ret < 0) {
dev_warn(smb->dev, "reading IRQSTAT_C failed\n");
return IRQ_NONE;
}
ret = regmap_read(smb->regmap, IRQSTAT_D, &irqstat_d);
if (ret < 0) {
dev_warn(smb->dev, "reading IRQSTAT_D failed\n");
return IRQ_NONE;
}
ret = regmap_read(smb->regmap, IRQSTAT_E, &irqstat_e);
if (ret < 0) {
dev_warn(smb->dev, "reading IRQSTAT_E failed\n");
return IRQ_NONE;
}
/*
* If we get charger error we report the error back to user.
* If the error is recovered charging will resume again.
*/
if (stat_c & STAT_C_CHARGER_ERROR) {
dev_err(smb->dev, "charging stopped due to charger error\n");
if (smb->use_mains)
power_supply_changed(smb->mains);
if (smb->use_usb)
power_supply_changed(smb->usb);
handled = true;
}
/*
* If we reached the termination current the battery is charged and
* we can update the status now. Charging is automatically
* disabled by the hardware.
*/
if (irqstat_c & (IRQSTAT_C_TERMINATION_IRQ | IRQSTAT_C_TAPER_IRQ)) {
if (irqstat_c & IRQSTAT_C_TERMINATION_STAT) {
if (smb->use_mains)
power_supply_changed(smb->mains);
if (smb->use_usb)
power_supply_changed(smb->usb);
}
dev_dbg(smb->dev, "going to HW maintenance mode\n");
handled = true;
}
/*
* If we got a charger timeout INT that means the charge
* full is not detected with in charge timeout value.
*/
if (irqstat_d & IRQSTAT_D_CHARGE_TIMEOUT_IRQ) {
dev_dbg(smb->dev, "total Charge Timeout INT received\n");
if (irqstat_d & IRQSTAT_D_CHARGE_TIMEOUT_STAT)
dev_warn(smb->dev, "charging stopped due to timeout\n");
if (smb->use_mains)
power_supply_changed(smb->mains);
if (smb->use_usb)
power_supply_changed(smb->usb);
handled = true;
}
/*
* If we got an under voltage interrupt it means that AC/USB input
* was connected or disconnected.
*/
if (irqstat_e & (IRQSTAT_E_USBIN_UV_IRQ | IRQSTAT_E_DCIN_UV_IRQ)) {
if (smb347_update_ps_status(smb) > 0) {
smb347_start_stop_charging(smb);
if (smb->use_mains)
power_supply_changed(smb->mains);
if (smb->use_usb)
power_supply_changed(smb->usb);
}
handled = true;
}
return handled ? IRQ_HANDLED : IRQ_NONE;
}
static int smb347_irq_set(struct smb347_charger *smb, bool enable)
{
int ret;
if (smb->irq_unsupported)
return 0;
ret = smb347_set_writable(smb, true, true);
if (ret < 0)
return ret;
/*
* Enable/disable interrupts for:
* - under voltage
* - termination current reached
* - charger timeout
* - charger error
*/
ret = regmap_update_bits(smb->regmap, CFG_FAULT_IRQ, 0xff,
enable ? CFG_FAULT_IRQ_DCIN_UV : 0);
if (ret < 0)
goto fail;
ret = regmap_update_bits(smb->regmap, CFG_STATUS_IRQ, 0xff,
enable ? (CFG_STATUS_IRQ_TERMINATION_OR_TAPER |
CFG_STATUS_IRQ_CHARGE_TIMEOUT) : 0);
if (ret < 0)
goto fail;
ret = regmap_update_bits(smb->regmap, CFG_PIN, CFG_PIN_EN_CHARGER_ERROR,
enable ? CFG_PIN_EN_CHARGER_ERROR : 0);
fail:
smb347_set_writable(smb, false, true);
return ret;
}
static inline int smb347_irq_enable(struct smb347_charger *smb)
{
return smb347_irq_set(smb, true);
}
static inline int smb347_irq_disable(struct smb347_charger *smb)
{
return smb347_irq_set(smb, false);
}
static int smb347_irq_init(struct smb347_charger *smb,
struct i2c_client *client)
{
int ret;
smb->irq_unsupported = true;
/*
* Interrupt pin is optional. If it is connected, we setup the
* interrupt support here.
*/
if (!client->irq)
return 0;
ret = smb347_set_writable(smb, true, false);
if (ret < 0)
return ret;
/*
* Configure the STAT output to be suitable for interrupts: disable
* all other output (except interrupts) and make it active low.
*/
ret = regmap_update_bits(smb->regmap, CFG_STAT,
CFG_STAT_ACTIVE_HIGH | CFG_STAT_DISABLED,
CFG_STAT_DISABLED);
smb347_set_writable(smb, false, false);
if (ret < 0) {
dev_warn(smb->dev, "failed to initialize IRQ: %d\n", ret);
dev_warn(smb->dev, "disabling IRQ support\n");
return 0;
}
ret = devm_request_threaded_irq(smb->dev, client->irq, NULL,
smb347_interrupt, IRQF_ONESHOT,
client->name, smb);
if (ret)
return ret;
smb->irq_unsupported = false;
ret = smb347_irq_enable(smb);
if (ret < 0)
return ret;
return 0;
}
/*
* Returns the constant charge current programmed
* into the charger in uA.
*/
static int get_const_charge_current(struct smb347_charger *smb)
{
unsigned int id = smb->id;
int ret, intval;
unsigned int v;
if (!smb347_is_ps_online(smb))
return -ENODATA;
ret = regmap_read(smb->regmap, STAT_B, &v);
if (ret < 0)
return ret;
/*
* The current value is composition of FCC and PCC values
* and we can detect which table to use from bit 5.
*/
if (v & 0x20) {
intval = hw_to_current(fcc_tbl[id],
ARRAY_SIZE(fcc_tbl[id]), v & 7);
} else {
v >>= 3;
intval = hw_to_current(pcc_tbl[id],
ARRAY_SIZE(pcc_tbl[id]), v & 7);
}
return intval;
}
/*
* Returns the constant charge voltage programmed
* into the charger in uV.
*/
static int get_const_charge_voltage(struct smb347_charger *smb)
{
int ret, intval;
unsigned int v;
if (!smb347_is_ps_online(smb))
return -ENODATA;
ret = regmap_read(smb->regmap, STAT_A, &v);
if (ret < 0)
return ret;
v &= STAT_A_FLOAT_VOLTAGE_MASK;
if (v > 0x3d)
v = 0x3d;
intval = 3500000 + v * 20000;
return intval;
}
static int smb347_get_charging_status(struct smb347_charger *smb,
struct power_supply *psy)
{
int ret, status;
unsigned int val;
if (psy->desc->type == POWER_SUPPLY_TYPE_USB) {
if (!smb->usb_online)
return POWER_SUPPLY_STATUS_DISCHARGING;
} else {
if (!smb->mains_online)
return POWER_SUPPLY_STATUS_DISCHARGING;
}
ret = regmap_read(smb->regmap, STAT_C, &val);
if (ret < 0)
return ret;
if ((val & STAT_C_CHARGER_ERROR) ||
(val & STAT_C_HOLDOFF_STAT)) {
/*
* set to NOT CHARGING upon charger error
* or charging has stopped.
*/
status = POWER_SUPPLY_STATUS_NOT_CHARGING;
} else {
if ((val & STAT_C_CHG_MASK) >> STAT_C_CHG_SHIFT) {
/*
* set to charging if battery is in pre-charge,
* fast charge or taper charging mode.
*/
status = POWER_SUPPLY_STATUS_CHARGING;
} else if (val & STAT_C_CHG_TERM) {
/*
* set the status to FULL if battery is not in pre
* charge, fast charge or taper charging mode AND
* charging is terminated at least once.
*/
status = POWER_SUPPLY_STATUS_FULL;
} else {
/*
* in this case no charger error or termination
* occured but charging is not in progress!!!
*/
status = POWER_SUPPLY_STATUS_NOT_CHARGING;
}
}
return status;
}
static int smb347_get_property_locked(struct power_supply *psy,
enum power_supply_property prop,
union power_supply_propval *val)
{
struct smb347_charger *smb = power_supply_get_drvdata(psy);
int ret;
switch (prop) {
case POWER_SUPPLY_PROP_STATUS:
ret = smb347_get_charging_status(smb, psy);
if (ret < 0)
return ret;
val->intval = ret;
break;
case POWER_SUPPLY_PROP_CHARGE_TYPE:
if (psy->desc->type == POWER_SUPPLY_TYPE_USB) {
if (!smb->usb_online)
return -ENODATA;
} else {
if (!smb->mains_online)
return -ENODATA;
}
/*
* We handle trickle and pre-charging the same, and taper
* and none the same.
*/
switch (smb347_charging_status(smb)) {
case 1:
val->intval = POWER_SUPPLY_CHARGE_TYPE_TRICKLE;
break;
case 2:
val->intval = POWER_SUPPLY_CHARGE_TYPE_FAST;
break;
default:
val->intval = POWER_SUPPLY_CHARGE_TYPE_NONE;
break;
}
break;
case POWER_SUPPLY_PROP_ONLINE:
if (psy->desc->type == POWER_SUPPLY_TYPE_USB)
val->intval = smb->usb_online;
else
val->intval = smb->mains_online;
break;
case POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE:
ret = get_const_charge_voltage(smb);
if (ret < 0)
return ret;
val->intval = ret;
break;
case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT:
ret = get_const_charge_current(smb);
if (ret < 0)
return ret;
val->intval = ret;
break;
default:
return -EINVAL;
}
return 0;
}
static int smb347_get_property(struct power_supply *psy,
enum power_supply_property prop,
union power_supply_propval *val)
{
struct smb347_charger *smb = power_supply_get_drvdata(psy);
struct i2c_client *client = to_i2c_client(smb->dev);
int ret;
if (!smb->irq_unsupported)
disable_irq(client->irq);
ret = smb347_get_property_locked(psy, prop, val);
if (!smb->irq_unsupported)
enable_irq(client->irq);
return ret;
}
static enum power_supply_property smb347_properties[] = {
POWER_SUPPLY_PROP_STATUS,
POWER_SUPPLY_PROP_CHARGE_TYPE,
POWER_SUPPLY_PROP_ONLINE,
POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT,
POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE,
};
static bool smb347_volatile_reg(struct device *dev, unsigned int reg)
{
switch (reg) {
case IRQSTAT_A:
case IRQSTAT_C:
case IRQSTAT_D:
case IRQSTAT_E:
case IRQSTAT_F:
case STAT_A:
case STAT_B:
case STAT_C:
case STAT_E:
return true;
}
return false;
}
static bool smb347_readable_reg(struct device *dev, unsigned int reg)
{
switch (reg) {
case CFG_CHARGE_CURRENT:
case CFG_CURRENT_LIMIT:
case CFG_FLOAT_VOLTAGE:
case CFG_STAT:
case CFG_PIN:
case CFG_THERM:
case CFG_SYSOK:
case CFG_OTHER:
case CFG_OTG:
case CFG_TEMP_LIMIT:
case CFG_FAULT_IRQ:
case CFG_STATUS_IRQ:
case CFG_ADDRESS:
case CMD_A:
case CMD_B:
case CMD_C:
return true;
}
return smb347_volatile_reg(dev, reg);
}
static void smb347_dt_parse_dev_info(struct smb347_charger *smb)
{
struct device *dev = smb->dev;
smb->soft_temp_limit_compensation =
SMB3XX_SOFT_TEMP_COMPENSATE_DEFAULT;
/*
* These properties come from the battery info, still we need to
* pre-initialize the values. See smb347_get_battery_info() below.
*/
smb->soft_cold_temp_limit = SMB3XX_TEMP_USE_DEFAULT;
smb->hard_cold_temp_limit = SMB3XX_TEMP_USE_DEFAULT;
smb->soft_hot_temp_limit = SMB3XX_TEMP_USE_DEFAULT;
smb->hard_hot_temp_limit = SMB3XX_TEMP_USE_DEFAULT;
/* Charging constraints */
device_property_read_u32(dev, "summit,fast-voltage-threshold-microvolt",
&smb->pre_to_fast_voltage);
device_property_read_u32(dev, "summit,mains-current-limit-microamp",
&smb->mains_current_limit);
device_property_read_u32(dev, "summit,usb-current-limit-microamp",
&smb->usb_hc_current_limit);
/* For thermometer monitoring */
device_property_read_u32(dev, "summit,chip-temperature-threshold-celsius",
&smb->chip_temp_threshold);
device_property_read_u32(dev, "summit,soft-compensation-method",
&smb->soft_temp_limit_compensation);
device_property_read_u32(dev, "summit,charge-current-compensation-microamp",
&smb->charge_current_compensation);
/* Supported charging mode */
smb->use_mains = device_property_read_bool(dev, "summit,enable-mains-charging");
smb->use_usb = device_property_read_bool(dev, "summit,enable-usb-charging");
smb->use_usb_otg = device_property_read_bool(dev, "summit,enable-otg-charging");
/* Select charging control */
device_property_read_u32(dev, "summit,enable-charge-control",
&smb->enable_control);
/*
* Polarity of INOK signal indicating presence of external power
* supply connected to the charger.
*/
device_property_read_u32(dev, "summit,inok-polarity",
&smb->inok_polarity);
}
static int smb347_get_battery_info(struct smb347_charger *smb)
{
struct power_supply_battery_info *info;
struct power_supply *supply;
int err;
if (smb->mains)
supply = smb->mains;
else
supply = smb->usb;
err = power_supply_get_battery_info(supply, &info);
if (err == -ENXIO || err == -ENODEV)
return 0;
if (err)
return err;
if (info->constant_charge_current_max_ua != -EINVAL)
smb->max_charge_current = info->constant_charge_current_max_ua;
if (info->constant_charge_voltage_max_uv != -EINVAL)
smb->max_charge_voltage = info->constant_charge_voltage_max_uv;
if (info->precharge_current_ua != -EINVAL)
smb->pre_charge_current = info->precharge_current_ua;
if (info->charge_term_current_ua != -EINVAL)
smb->termination_current = info->charge_term_current_ua;
if (info->temp_alert_min != INT_MIN)
smb->soft_cold_temp_limit = info->temp_alert_min;
if (info->temp_alert_max != INT_MAX)
smb->soft_hot_temp_limit = info->temp_alert_max;
if (info->temp_min != INT_MIN)
smb->hard_cold_temp_limit = info->temp_min;
if (info->temp_max != INT_MAX)
smb->hard_hot_temp_limit = info->temp_max;
/* Suspend when battery temperature is outside hard limits */
if (smb->hard_cold_temp_limit != SMB3XX_TEMP_USE_DEFAULT ||
smb->hard_hot_temp_limit != SMB3XX_TEMP_USE_DEFAULT)
smb->suspend_on_hard_temp_limit = true;
return 0;
}
static int smb347_usb_vbus_get_current_limit(struct regulator_dev *rdev)
{
struct smb347_charger *smb = rdev_get_drvdata(rdev);
unsigned int val;
int ret;
ret = regmap_read(smb->regmap, CFG_OTG, &val);
if (ret < 0)
return ret;
/*
* It's unknown what happens if this bit is unset due to lack of
* access to the datasheet, assume it's limit-enable.
*/
if (!(val & CFG_OTG_CURRENT_LIMIT_250mA))
return 0;
return val & CFG_OTG_CURRENT_LIMIT_750mA ? 750000 : 250000;
}
static int smb347_usb_vbus_set_new_current_limit(struct smb347_charger *smb,
int max_uA)
{
const unsigned int mask = CFG_OTG_CURRENT_LIMIT_750mA |
CFG_OTG_CURRENT_LIMIT_250mA;
unsigned int val = CFG_OTG_CURRENT_LIMIT_250mA;
int ret;
if (max_uA >= 750000)
val |= CFG_OTG_CURRENT_LIMIT_750mA;
ret = regmap_update_bits(smb->regmap, CFG_OTG, mask, val);
if (ret < 0)
dev_err(smb->dev, "failed to change USB current limit\n");
return ret;
}
static int smb347_usb_vbus_set_current_limit(struct regulator_dev *rdev,
int min_uA, int max_uA)
{
struct smb347_charger *smb = rdev_get_drvdata(rdev);
int ret;
ret = smb347_set_writable(smb, true, true);
if (ret < 0)
return ret;
ret = smb347_usb_vbus_set_new_current_limit(smb, max_uA);
smb347_set_writable(smb, false, true);
return ret;
}
static int smb347_usb_vbus_regulator_enable(struct regulator_dev *rdev)
{
struct smb347_charger *smb = rdev_get_drvdata(rdev);
int ret, max_uA;
ret = smb347_set_writable(smb, true, true);
if (ret < 0)
return ret;
smb347_charging_disable(smb);
if (device_property_read_bool(&rdev->dev, "summit,needs-inok-toggle")) {
unsigned int sysok = 0;
if (smb->inok_polarity == SMB3XX_SYSOK_INOK_ACTIVE_LOW)
sysok = CFG_SYSOK_INOK_ACTIVE_HIGH;
/*
* VBUS won't be powered if INOK is active, so we need to
* manually disable INOK on some platforms.
*/
ret = regmap_update_bits(smb->regmap, CFG_SYSOK,
CFG_SYSOK_INOK_ACTIVE_HIGH, sysok);
if (ret < 0) {
dev_err(smb->dev, "failed to disable INOK\n");
goto done;
}
}
ret = smb347_usb_vbus_get_current_limit(rdev);
if (ret < 0) {
dev_err(smb->dev, "failed to get USB VBUS current limit\n");
goto done;
}
max_uA = ret;
ret = smb347_usb_vbus_set_new_current_limit(smb, 250000);
if (ret < 0) {
dev_err(smb->dev, "failed to preset USB VBUS current limit\n");
goto done;
}
ret = regmap_set_bits(smb->regmap, CMD_A, CMD_A_OTG_ENABLED);
if (ret < 0) {
dev_err(smb->dev, "failed to enable USB VBUS\n");
goto done;
}
smb->usb_vbus_enabled = true;
ret = smb347_usb_vbus_set_new_current_limit(smb, max_uA);
if (ret < 0) {
dev_err(smb->dev, "failed to restore USB VBUS current limit\n");
goto done;
}
done:
smb347_set_writable(smb, false, true);
return ret;
}
static int smb347_usb_vbus_regulator_disable(struct regulator_dev *rdev)
{
struct smb347_charger *smb = rdev_get_drvdata(rdev);
int ret;
ret = smb347_set_writable(smb, true, true);
if (ret < 0)
return ret;
ret = regmap_clear_bits(smb->regmap, CMD_A, CMD_A_OTG_ENABLED);
if (ret < 0) {
dev_err(smb->dev, "failed to disable USB VBUS\n");
goto done;
}
smb->usb_vbus_enabled = false;
if (device_property_read_bool(&rdev->dev, "summit,needs-inok-toggle")) {
unsigned int sysok = 0;
if (smb->inok_polarity == SMB3XX_SYSOK_INOK_ACTIVE_HIGH)
sysok = CFG_SYSOK_INOK_ACTIVE_HIGH;
ret = regmap_update_bits(smb->regmap, CFG_SYSOK,
CFG_SYSOK_INOK_ACTIVE_HIGH, sysok);
if (ret < 0) {
dev_err(smb->dev, "failed to enable INOK\n");
goto done;
}
}
smb347_start_stop_charging(smb);
done:
smb347_set_writable(smb, false, true);
return ret;
}
static const struct regmap_config smb347_regmap = {
.reg_bits = 8,
.val_bits = 8,
.max_register = SMB347_MAX_REGISTER,
.volatile_reg = smb347_volatile_reg,
.readable_reg = smb347_readable_reg,
.cache_type = REGCACHE_RBTREE,
};
static const struct regulator_ops smb347_usb_vbus_regulator_ops = {
.is_enabled = regulator_is_enabled_regmap,
.enable = smb347_usb_vbus_regulator_enable,
.disable = smb347_usb_vbus_regulator_disable,
.get_current_limit = smb347_usb_vbus_get_current_limit,
.set_current_limit = smb347_usb_vbus_set_current_limit,
};
static const struct power_supply_desc smb347_mains_desc = {
.name = "smb347-mains",
.type = POWER_SUPPLY_TYPE_MAINS,
.get_property = smb347_get_property,
.properties = smb347_properties,
.num_properties = ARRAY_SIZE(smb347_properties),
};
static const struct power_supply_desc smb347_usb_desc = {
.name = "smb347-usb",
.type = POWER_SUPPLY_TYPE_USB,
.get_property = smb347_get_property,
.properties = smb347_properties,
.num_properties = ARRAY_SIZE(smb347_properties),
};
static const struct regulator_desc smb347_usb_vbus_regulator_desc = {
.name = "smb347-usb-vbus",
.of_match = of_match_ptr("usb-vbus"),
.ops = &smb347_usb_vbus_regulator_ops,
.type = REGULATOR_VOLTAGE,
.owner = THIS_MODULE,
.enable_reg = CMD_A,
.enable_mask = CMD_A_OTG_ENABLED,
.enable_val = CMD_A_OTG_ENABLED,
.fixed_uV = 5000000,
.n_voltages = 1,
};
static int smb347_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
struct power_supply_config mains_usb_cfg = {};
struct regulator_config usb_rdev_cfg = {};
struct device *dev = &client->dev;
struct smb347_charger *smb;
int ret;
smb = devm_kzalloc(dev, sizeof(*smb), GFP_KERNEL);
if (!smb)
return -ENOMEM;
smb->dev = &client->dev;
smb->id = id->driver_data;
i2c_set_clientdata(client, smb);
smb347_dt_parse_dev_info(smb);
if (!smb->use_mains && !smb->use_usb)
return -EINVAL;
smb->regmap = devm_regmap_init_i2c(client, &smb347_regmap);
if (IS_ERR(smb->regmap))
return PTR_ERR(smb->regmap);
mains_usb_cfg.drv_data = smb;
mains_usb_cfg.of_node = dev->of_node;
if (smb->use_mains) {
smb->mains = devm_power_supply_register(dev, &smb347_mains_desc,
&mains_usb_cfg);
if (IS_ERR(smb->mains))
return PTR_ERR(smb->mains);
}
if (smb->use_usb) {
smb->usb = devm_power_supply_register(dev, &smb347_usb_desc,
&mains_usb_cfg);
if (IS_ERR(smb->usb))
return PTR_ERR(smb->usb);
}
ret = smb347_get_battery_info(smb);
if (ret)
return ret;
ret = smb347_hw_init(smb);
if (ret < 0)
return ret;
ret = smb347_irq_init(smb, client);
if (ret)
return ret;
usb_rdev_cfg.dev = dev;
usb_rdev_cfg.driver_data = smb;
usb_rdev_cfg.regmap = smb->regmap;
smb->usb_rdev = devm_regulator_register(dev,
&smb347_usb_vbus_regulator_desc,
&usb_rdev_cfg);
if (IS_ERR(smb->usb_rdev)) {
smb347_irq_disable(smb);
return PTR_ERR(smb->usb_rdev);
}
return 0;
}
static int smb347_remove(struct i2c_client *client)
{
struct smb347_charger *smb = i2c_get_clientdata(client);
smb347_usb_vbus_regulator_disable(smb->usb_rdev);
smb347_irq_disable(smb);
return 0;
}
static void smb347_shutdown(struct i2c_client *client)
{
smb347_remove(client);
}
static const struct i2c_device_id smb347_id[] = {
{ "smb345", SMB345 },
{ "smb347", SMB347 },
{ "smb358", SMB358 },
{ },
};
MODULE_DEVICE_TABLE(i2c, smb347_id);
static const struct of_device_id smb3xx_of_match[] = {
{ .compatible = "summit,smb345" },
{ .compatible = "summit,smb347" },
{ .compatible = "summit,smb358" },
{ },
};
MODULE_DEVICE_TABLE(of, smb3xx_of_match);
static struct i2c_driver smb347_driver = {
.driver = {
.name = "smb347",
.of_match_table = smb3xx_of_match,
},
.probe = smb347_probe,
.remove = smb347_remove,
.shutdown = smb347_shutdown,
.id_table = smb347_id,
};
module_i2c_driver(smb347_driver);
MODULE_AUTHOR("Bruce E. Robertson <bruce.e.robertson@intel.com>");
MODULE_AUTHOR("Mika Westerberg <mika.westerberg@linux.intel.com>");
MODULE_DESCRIPTION("SMB347 battery charger driver");
MODULE_LICENSE("GPL");