| // SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| /* |
| * Copyright 2019 NXP |
| */ |
| |
| #include <dt-bindings/clock/imx8mm-clock.h> |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| #include <dt-bindings/thermal/thermal.h> |
| |
| #include "imx8mm-pinfunc.h" |
| |
| / { |
| compatible = "fsl,imx8mm"; |
| interrupt-parent = <&gic>; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| |
| aliases { |
| ethernet0 = &fec1; |
| i2c0 = &i2c1; |
| i2c1 = &i2c2; |
| i2c2 = &i2c3; |
| i2c3 = &i2c4; |
| serial0 = &uart1; |
| serial1 = &uart2; |
| serial2 = &uart3; |
| serial3 = &uart4; |
| spi0 = &ecspi1; |
| spi1 = &ecspi2; |
| spi2 = &ecspi3; |
| mmc0 = &usdhc1; |
| mmc1 = &usdhc2; |
| mmc2 = &usdhc3; |
| gpio0 = &gpio1; |
| gpio1 = &gpio2; |
| gpio2 = &gpio3; |
| gpio3 = &gpio4; |
| gpio4 = &gpio5; |
| }; |
| |
| cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| idle-states { |
| entry-method = "psci"; |
| |
| cpu_pd_wait: cpu-pd-wait { |
| compatible = "arm,idle-state"; |
| arm,psci-suspend-param = <0x0010033>; |
| local-timer-stop; |
| entry-latency-us = <1000>; |
| exit-latency-us = <700>; |
| min-residency-us = <2700>; |
| }; |
| }; |
| |
| A53_0: cpu@0 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a53"; |
| reg = <0x0>; |
| clock-latency = <61036>; /* two CLK32 periods */ |
| clocks = <&clk IMX8MM_CLK_ARM>; |
| enable-method = "psci"; |
| next-level-cache = <&A53_L2>; |
| operating-points-v2 = <&a53_opp_table>; |
| nvmem-cells = <&cpu_speed_grade>; |
| nvmem-cell-names = "speed_grade"; |
| cpu-idle-states = <&cpu_pd_wait>; |
| }; |
| |
| A53_1: cpu@1 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a53"; |
| reg = <0x1>; |
| clock-latency = <61036>; /* two CLK32 periods */ |
| clocks = <&clk IMX8MM_CLK_ARM>; |
| enable-method = "psci"; |
| next-level-cache = <&A53_L2>; |
| operating-points-v2 = <&a53_opp_table>; |
| cpu-idle-states = <&cpu_pd_wait>; |
| }; |
| |
| A53_2: cpu@2 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a53"; |
| reg = <0x2>; |
| clock-latency = <61036>; /* two CLK32 periods */ |
| clocks = <&clk IMX8MM_CLK_ARM>; |
| enable-method = "psci"; |
| next-level-cache = <&A53_L2>; |
| operating-points-v2 = <&a53_opp_table>; |
| cpu-idle-states = <&cpu_pd_wait>; |
| }; |
| |
| A53_3: cpu@3 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a53"; |
| reg = <0x3>; |
| clock-latency = <61036>; /* two CLK32 periods */ |
| clocks = <&clk IMX8MM_CLK_ARM>; |
| enable-method = "psci"; |
| next-level-cache = <&A53_L2>; |
| operating-points-v2 = <&a53_opp_table>; |
| cpu-idle-states = <&cpu_pd_wait>; |
| }; |
| |
| A53_L2: l2-cache0 { |
| compatible = "cache"; |
| }; |
| }; |
| |
| a53_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| opp-shared; |
| |
| opp-1200000000 { |
| opp-hz = /bits/ 64 <1200000000>; |
| opp-microvolt = <850000>; |
| opp-supported-hw = <0xe>, <0x7>; |
| clock-latency-ns = <150000>; |
| opp-suspend; |
| }; |
| |
| opp-1600000000 { |
| opp-hz = /bits/ 64 <1600000000>; |
| opp-microvolt = <900000>; |
| opp-supported-hw = <0xc>, <0x7>; |
| clock-latency-ns = <150000>; |
| opp-suspend; |
| }; |
| |
| opp-1800000000 { |
| opp-hz = /bits/ 64 <1800000000>; |
| opp-microvolt = <1000000>; |
| opp-supported-hw = <0x8>, <0x3>; |
| clock-latency-ns = <150000>; |
| opp-suspend; |
| }; |
| }; |
| |
| memory@40000000 { |
| device_type = "memory"; |
| reg = <0x0 0x40000000 0 0x80000000>; |
| }; |
| |
| osc_32k: clock-osc-32k { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <32768>; |
| clock-output-names = "osc_32k"; |
| }; |
| |
| osc_24m: clock-osc-24m { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <24000000>; |
| clock-output-names = "osc_24m"; |
| }; |
| |
| clk_ext1: clock-ext1 { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <133000000>; |
| clock-output-names = "clk_ext1"; |
| }; |
| |
| clk_ext2: clock-ext2 { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <133000000>; |
| clock-output-names = "clk_ext2"; |
| }; |
| |
| clk_ext3: clock-ext3 { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <133000000>; |
| clock-output-names = "clk_ext3"; |
| }; |
| |
| clk_ext4: clock-ext4 { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency= <133000000>; |
| clock-output-names = "clk_ext4"; |
| }; |
| |
| psci { |
| compatible = "arm,psci-1.0"; |
| method = "smc"; |
| }; |
| |
| pmu { |
| compatible = "arm,armv8-pmuv3"; |
| interrupts = <GIC_PPI 7 |
| (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_HIGH)>; |
| interrupt-affinity = <&A53_0>, <&A53_1>, <&A53_2>, <&A53_3>; |
| }; |
| |
| timer { |
| compatible = "arm,armv8-timer"; |
| interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>, /* Physical Secure */ |
| <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>, /* Physical Non-Secure */ |
| <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>, /* Virtual */ |
| <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>; /* Hypervisor */ |
| clock-frequency = <8000000>; |
| arm,no-tick-in-suspend; |
| }; |
| |
| usbphynop1: usbphynop1 { |
| compatible = "usb-nop-xceiv"; |
| clocks = <&clk IMX8MM_CLK_USB_PHY_REF>; |
| assigned-clocks = <&clk IMX8MM_CLK_USB_PHY_REF>; |
| assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_100M>; |
| clock-names = "main_clk"; |
| }; |
| |
| usbphynop2: usbphynop2 { |
| compatible = "usb-nop-xceiv"; |
| clocks = <&clk IMX8MM_CLK_USB_PHY_REF>; |
| assigned-clocks = <&clk IMX8MM_CLK_USB_PHY_REF>; |
| assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_100M>; |
| clock-names = "main_clk"; |
| }; |
| |
| soc@0 { |
| compatible = "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0x0 0x0 0x0 0x3e000000>; |
| |
| aips1: bus@30000000 { |
| compatible = "fsl,aips-bus", "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0x30000000 0x30000000 0x400000>; |
| |
| sai1: sai@30010000 { |
| compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai"; |
| reg = <0x30010000 0x10000>; |
| interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MM_CLK_SAI1_IPG>, |
| <&clk IMX8MM_CLK_SAI1_ROOT>, |
| <&clk IMX8MM_CLK_DUMMY>, <&clk IMX8MM_CLK_DUMMY>; |
| clock-names = "bus", "mclk1", "mclk2", "mclk3"; |
| dmas = <&sdma2 0 2 0>, <&sdma2 1 2 0>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| sai2: sai@30020000 { |
| compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai"; |
| reg = <0x30020000 0x10000>; |
| interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MM_CLK_SAI2_IPG>, |
| <&clk IMX8MM_CLK_SAI2_ROOT>, |
| <&clk IMX8MM_CLK_DUMMY>, <&clk IMX8MM_CLK_DUMMY>; |
| clock-names = "bus", "mclk1", "mclk2", "mclk3"; |
| dmas = <&sdma2 2 2 0>, <&sdma2 3 2 0>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| sai3: sai@30030000 { |
| #sound-dai-cells = <0>; |
| compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai"; |
| reg = <0x30030000 0x10000>; |
| interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MM_CLK_SAI3_IPG>, |
| <&clk IMX8MM_CLK_SAI3_ROOT>, |
| <&clk IMX8MM_CLK_DUMMY>, <&clk IMX8MM_CLK_DUMMY>; |
| clock-names = "bus", "mclk1", "mclk2", "mclk3"; |
| dmas = <&sdma2 4 2 0>, <&sdma2 5 2 0>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| sai5: sai@30050000 { |
| compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai"; |
| reg = <0x30050000 0x10000>; |
| interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MM_CLK_SAI5_IPG>, |
| <&clk IMX8MM_CLK_SAI5_ROOT>, |
| <&clk IMX8MM_CLK_DUMMY>, <&clk IMX8MM_CLK_DUMMY>; |
| clock-names = "bus", "mclk1", "mclk2", "mclk3"; |
| dmas = <&sdma2 8 2 0>, <&sdma2 9 2 0>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| sai6: sai@30060000 { |
| compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai"; |
| reg = <0x30060000 0x10000>; |
| interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MM_CLK_SAI6_IPG>, |
| <&clk IMX8MM_CLK_SAI6_ROOT>, |
| <&clk IMX8MM_CLK_DUMMY>, <&clk IMX8MM_CLK_DUMMY>; |
| clock-names = "bus", "mclk1", "mclk2", "mclk3"; |
| dmas = <&sdma2 10 2 0>, <&sdma2 11 2 0>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| gpio1: gpio@30200000 { |
| compatible = "fsl,imx8mm-gpio", "fsl,imx35-gpio"; |
| reg = <0x30200000 0x10000>; |
| interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MM_CLK_GPIO1_ROOT>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| gpio-ranges = <&iomuxc 0 10 30>; |
| }; |
| |
| gpio2: gpio@30210000 { |
| compatible = "fsl,imx8mm-gpio", "fsl,imx35-gpio"; |
| reg = <0x30210000 0x10000>; |
| interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MM_CLK_GPIO2_ROOT>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| gpio-ranges = <&iomuxc 0 40 21>; |
| }; |
| |
| gpio3: gpio@30220000 { |
| compatible = "fsl,imx8mm-gpio", "fsl,imx35-gpio"; |
| reg = <0x30220000 0x10000>; |
| interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MM_CLK_GPIO3_ROOT>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| gpio-ranges = <&iomuxc 0 61 26>; |
| }; |
| |
| gpio4: gpio@30230000 { |
| compatible = "fsl,imx8mm-gpio", "fsl,imx35-gpio"; |
| reg = <0x30230000 0x10000>; |
| interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MM_CLK_GPIO4_ROOT>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| gpio-ranges = <&iomuxc 0 87 32>; |
| }; |
| |
| gpio5: gpio@30240000 { |
| compatible = "fsl,imx8mm-gpio", "fsl,imx35-gpio"; |
| reg = <0x30240000 0x10000>; |
| interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MM_CLK_GPIO5_ROOT>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| gpio-ranges = <&iomuxc 0 119 30>; |
| }; |
| |
| wdog1: watchdog@30280000 { |
| compatible = "fsl,imx8mm-wdt", "fsl,imx21-wdt"; |
| reg = <0x30280000 0x10000>; |
| interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MM_CLK_WDOG1_ROOT>; |
| status = "disabled"; |
| }; |
| |
| wdog2: watchdog@30290000 { |
| compatible = "fsl,imx8mm-wdt", "fsl,imx21-wdt"; |
| reg = <0x30290000 0x10000>; |
| interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MM_CLK_WDOG2_ROOT>; |
| status = "disabled"; |
| }; |
| |
| wdog3: watchdog@302a0000 { |
| compatible = "fsl,imx8mm-wdt", "fsl,imx21-wdt"; |
| reg = <0x302a0000 0x10000>; |
| interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MM_CLK_WDOG3_ROOT>; |
| status = "disabled"; |
| }; |
| |
| sdma2: dma-controller@302c0000 { |
| compatible = "fsl,imx8mm-sdma", "fsl,imx8mq-sdma"; |
| reg = <0x302c0000 0x10000>; |
| interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MM_CLK_SDMA2_ROOT>, |
| <&clk IMX8MM_CLK_SDMA2_ROOT>; |
| clock-names = "ipg", "ahb"; |
| #dma-cells = <3>; |
| fsl,sdma-ram-script-name = "imx/sdma/sdma-imx7d.bin"; |
| }; |
| |
| sdma3: dma-controller@302b0000 { |
| compatible = "fsl,imx8mm-sdma", "fsl,imx8mq-sdma"; |
| reg = <0x302b0000 0x10000>; |
| interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MM_CLK_SDMA3_ROOT>, |
| <&clk IMX8MM_CLK_SDMA3_ROOT>; |
| clock-names = "ipg", "ahb"; |
| #dma-cells = <3>; |
| fsl,sdma-ram-script-name = "imx/sdma/sdma-imx7d.bin"; |
| }; |
| |
| iomuxc: pinctrl@30330000 { |
| compatible = "fsl,imx8mm-iomuxc"; |
| reg = <0x30330000 0x10000>; |
| }; |
| |
| gpr: iomuxc-gpr@30340000 { |
| compatible = "fsl,imx8mm-iomuxc-gpr", "syscon"; |
| reg = <0x30340000 0x10000>; |
| }; |
| |
| ocotp: ocotp-ctrl@30350000 { |
| compatible = "fsl,imx8mm-ocotp", "fsl,imx7d-ocotp", "syscon"; |
| reg = <0x30350000 0x10000>; |
| clocks = <&clk IMX8MM_CLK_OCOTP_ROOT>; |
| /* For nvmem subnodes */ |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| cpu_speed_grade: speed-grade@10 { |
| reg = <0x10 4>; |
| }; |
| }; |
| |
| anatop: anatop@30360000 { |
| compatible = "fsl,imx8mm-anatop", "syscon", "simple-bus"; |
| reg = <0x30360000 0x10000>; |
| }; |
| |
| snvs: snvs@30370000 { |
| compatible = "fsl,sec-v4.0-mon","syscon", "simple-mfd"; |
| reg = <0x30370000 0x10000>; |
| |
| snvs_rtc: snvs-rtc-lp { |
| compatible = "fsl,sec-v4.0-mon-rtc-lp"; |
| regmap = <&snvs>; |
| offset = <0x34>; |
| interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MM_CLK_SNVS_ROOT>; |
| clock-names = "snvs-rtc"; |
| }; |
| |
| snvs_pwrkey: snvs-powerkey { |
| compatible = "fsl,sec-v4.0-pwrkey"; |
| regmap = <&snvs>; |
| interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; |
| linux,keycode = <KEY_POWER>; |
| wakeup-source; |
| status = "disabled"; |
| }; |
| }; |
| |
| clk: clock-controller@30380000 { |
| compatible = "fsl,imx8mm-ccm"; |
| reg = <0x30380000 0x10000>; |
| #clock-cells = <1>; |
| clocks = <&osc_32k>, <&osc_24m>, <&clk_ext1>, <&clk_ext2>, |
| <&clk_ext3>, <&clk_ext4>; |
| clock-names = "osc_32k", "osc_24m", "clk_ext1", "clk_ext2", |
| "clk_ext3", "clk_ext4"; |
| assigned-clocks = <&clk IMX8MM_CLK_NOC>, |
| <&clk IMX8MM_CLK_AUDIO_AHB>, |
| <&clk IMX8MM_CLK_IPG_AUDIO_ROOT>, |
| <&clk IMX8MM_SYS_PLL3>, |
| <&clk IMX8MM_VIDEO_PLL1>; |
| assigned-clock-parents = <&clk IMX8MM_SYS_PLL3_OUT>, |
| <&clk IMX8MM_SYS_PLL1_800M>; |
| assigned-clock-rates = <0>, |
| <400000000>, |
| <400000000>, |
| <750000000>, |
| <594000000>; |
| }; |
| |
| src: reset-controller@30390000 { |
| compatible = "fsl,imx8mm-src", "fsl,imx8mq-src", "syscon"; |
| reg = <0x30390000 0x10000>; |
| interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>; |
| #reset-cells = <1>; |
| }; |
| }; |
| |
| aips2: bus@30400000 { |
| compatible = "fsl,aips-bus", "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0x30400000 0x30400000 0x400000>; |
| |
| pwm1: pwm@30660000 { |
| compatible = "fsl,imx8mm-pwm", "fsl,imx27-pwm"; |
| reg = <0x30660000 0x10000>; |
| interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MM_CLK_PWM1_ROOT>, |
| <&clk IMX8MM_CLK_PWM1_ROOT>; |
| clock-names = "ipg", "per"; |
| #pwm-cells = <2>; |
| status = "disabled"; |
| }; |
| |
| pwm2: pwm@30670000 { |
| compatible = "fsl,imx8mm-pwm", "fsl,imx27-pwm"; |
| reg = <0x30670000 0x10000>; |
| interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MM_CLK_PWM2_ROOT>, |
| <&clk IMX8MM_CLK_PWM2_ROOT>; |
| clock-names = "ipg", "per"; |
| #pwm-cells = <2>; |
| status = "disabled"; |
| }; |
| |
| pwm3: pwm@30680000 { |
| compatible = "fsl,imx8mm-pwm", "fsl,imx27-pwm"; |
| reg = <0x30680000 0x10000>; |
| interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MM_CLK_PWM3_ROOT>, |
| <&clk IMX8MM_CLK_PWM3_ROOT>; |
| clock-names = "ipg", "per"; |
| #pwm-cells = <2>; |
| status = "disabled"; |
| }; |
| |
| pwm4: pwm@30690000 { |
| compatible = "fsl,imx8mm-pwm", "fsl,imx27-pwm"; |
| reg = <0x30690000 0x10000>; |
| interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MM_CLK_PWM4_ROOT>, |
| <&clk IMX8MM_CLK_PWM4_ROOT>; |
| clock-names = "ipg", "per"; |
| #pwm-cells = <2>; |
| status = "disabled"; |
| }; |
| |
| system_counter: timer@306a0000 { |
| compatible = "nxp,sysctr-timer"; |
| reg = <0x306a0000 0x20000>; |
| interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&osc_24m>; |
| clock-names = "per"; |
| }; |
| }; |
| |
| aips3: bus@30800000 { |
| compatible = "fsl,aips-bus", "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0x30800000 0x30800000 0x400000>; |
| |
| ecspi1: spi@30820000 { |
| compatible = "fsl,imx8mm-ecspi", "fsl,imx51-ecspi"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x30820000 0x10000>; |
| interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MM_CLK_ECSPI1_ROOT>, |
| <&clk IMX8MM_CLK_ECSPI1_ROOT>; |
| clock-names = "ipg", "per"; |
| dmas = <&sdma1 0 7 1>, <&sdma1 1 7 2>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| ecspi2: spi@30830000 { |
| compatible = "fsl,imx8mm-ecspi", "fsl,imx51-ecspi"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x30830000 0x10000>; |
| interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MM_CLK_ECSPI2_ROOT>, |
| <&clk IMX8MM_CLK_ECSPI2_ROOT>; |
| clock-names = "ipg", "per"; |
| dmas = <&sdma1 2 7 1>, <&sdma1 3 7 2>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| ecspi3: spi@30840000 { |
| compatible = "fsl,imx8mm-ecspi", "fsl,imx51-ecspi"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x30840000 0x10000>; |
| interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MM_CLK_ECSPI3_ROOT>, |
| <&clk IMX8MM_CLK_ECSPI3_ROOT>; |
| clock-names = "ipg", "per"; |
| dmas = <&sdma1 4 7 1>, <&sdma1 5 7 2>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| uart1: serial@30860000 { |
| compatible = "fsl,imx8mm-uart", "fsl,imx6q-uart"; |
| reg = <0x30860000 0x10000>; |
| interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MM_CLK_UART1_ROOT>, |
| <&clk IMX8MM_CLK_UART1_ROOT>; |
| clock-names = "ipg", "per"; |
| dmas = <&sdma1 22 4 0>, <&sdma1 23 4 0>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| uart3: serial@30880000 { |
| compatible = "fsl,imx8mm-uart", "fsl,imx6q-uart"; |
| reg = <0x30880000 0x10000>; |
| interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MM_CLK_UART3_ROOT>, |
| <&clk IMX8MM_CLK_UART3_ROOT>; |
| clock-names = "ipg", "per"; |
| dmas = <&sdma1 26 4 0>, <&sdma1 27 4 0>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| uart2: serial@30890000 { |
| compatible = "fsl,imx8mm-uart", "fsl,imx6q-uart"; |
| reg = <0x30890000 0x10000>; |
| interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MM_CLK_UART2_ROOT>, |
| <&clk IMX8MM_CLK_UART2_ROOT>; |
| clock-names = "ipg", "per"; |
| status = "disabled"; |
| }; |
| |
| i2c1: i2c@30a20000 { |
| compatible = "fsl,imx8mm-i2c", "fsl,imx21-i2c"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x30a20000 0x10000>; |
| interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MM_CLK_I2C1_ROOT>; |
| status = "disabled"; |
| }; |
| |
| i2c2: i2c@30a30000 { |
| compatible = "fsl,imx8mm-i2c", "fsl,imx21-i2c"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x30a30000 0x10000>; |
| interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MM_CLK_I2C2_ROOT>; |
| status = "disabled"; |
| }; |
| |
| i2c3: i2c@30a40000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx8mm-i2c", "fsl,imx21-i2c"; |
| reg = <0x30a40000 0x10000>; |
| interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MM_CLK_I2C3_ROOT>; |
| status = "disabled"; |
| }; |
| |
| i2c4: i2c@30a50000 { |
| compatible = "fsl,imx8mm-i2c", "fsl,imx21-i2c"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x30a50000 0x10000>; |
| interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MM_CLK_I2C4_ROOT>; |
| status = "disabled"; |
| }; |
| |
| uart4: serial@30a60000 { |
| compatible = "fsl,imx8mm-uart", "fsl,imx6q-uart"; |
| reg = <0x30a60000 0x10000>; |
| interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MM_CLK_UART4_ROOT>, |
| <&clk IMX8MM_CLK_UART4_ROOT>; |
| clock-names = "ipg", "per"; |
| dmas = <&sdma1 28 4 0>, <&sdma1 29 4 0>; |
| dma-names = "rx", "tx"; |
| status = "disabled"; |
| }; |
| |
| usdhc1: mmc@30b40000 { |
| compatible = "fsl,imx8mm-usdhc", "fsl,imx7d-usdhc"; |
| reg = <0x30b40000 0x10000>; |
| interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MM_CLK_IPG_ROOT>, |
| <&clk IMX8MM_CLK_NAND_USDHC_BUS>, |
| <&clk IMX8MM_CLK_USDHC1_ROOT>; |
| clock-names = "ipg", "ahb", "per"; |
| assigned-clocks = <&clk IMX8MM_CLK_USDHC1>; |
| assigned-clock-rates = <400000000>; |
| fsl,tuning-start-tap = <20>; |
| fsl,tuning-step= <2>; |
| bus-width = <4>; |
| status = "disabled"; |
| }; |
| |
| usdhc2: mmc@30b50000 { |
| compatible = "fsl,imx8mm-usdhc", "fsl,imx7d-usdhc"; |
| reg = <0x30b50000 0x10000>; |
| interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MM_CLK_IPG_ROOT>, |
| <&clk IMX8MM_CLK_NAND_USDHC_BUS>, |
| <&clk IMX8MM_CLK_USDHC2_ROOT>; |
| clock-names = "ipg", "ahb", "per"; |
| fsl,tuning-start-tap = <20>; |
| fsl,tuning-step= <2>; |
| bus-width = <4>; |
| status = "disabled"; |
| }; |
| |
| usdhc3: mmc@30b60000 { |
| compatible = "fsl,imx8mm-usdhc", "fsl,imx7d-usdhc"; |
| reg = <0x30b60000 0x10000>; |
| interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MM_CLK_IPG_ROOT>, |
| <&clk IMX8MM_CLK_NAND_USDHC_BUS>, |
| <&clk IMX8MM_CLK_USDHC3_ROOT>; |
| clock-names = "ipg", "ahb", "per"; |
| assigned-clocks = <&clk IMX8MM_CLK_USDHC3_ROOT>; |
| assigned-clock-rates = <400000000>; |
| fsl,tuning-start-tap = <20>; |
| fsl,tuning-step= <2>; |
| bus-width = <4>; |
| status = "disabled"; |
| }; |
| |
| sdma1: dma-controller@30bd0000 { |
| compatible = "fsl,imx8mm-sdma", "fsl,imx8mq-sdma"; |
| reg = <0x30bd0000 0x10000>; |
| interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MM_CLK_SDMA1_ROOT>, |
| <&clk IMX8MM_CLK_SDMA1_ROOT>; |
| clock-names = "ipg", "ahb"; |
| #dma-cells = <3>; |
| fsl,sdma-ram-script-name = "imx/sdma/sdma-imx7d.bin"; |
| }; |
| |
| fec1: ethernet@30be0000 { |
| compatible = "fsl,imx8mm-fec", "fsl,imx6sx-fec"; |
| reg = <0x30be0000 0x10000>; |
| interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MM_CLK_ENET1_ROOT>, |
| <&clk IMX8MM_CLK_ENET1_ROOT>, |
| <&clk IMX8MM_CLK_ENET_TIMER>, |
| <&clk IMX8MM_CLK_ENET_REF>, |
| <&clk IMX8MM_CLK_ENET_PHY_REF>; |
| clock-names = "ipg", "ahb", "ptp", |
| "enet_clk_ref", "enet_out"; |
| assigned-clocks = <&clk IMX8MM_CLK_ENET_AXI>, |
| <&clk IMX8MM_CLK_ENET_TIMER>, |
| <&clk IMX8MM_CLK_ENET_REF>, |
| <&clk IMX8MM_CLK_ENET_TIMER>; |
| assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_266M>, |
| <&clk IMX8MM_SYS_PLL2_100M>, |
| <&clk IMX8MM_SYS_PLL2_125M>; |
| assigned-clock-rates = <0>, <0>, <125000000>, <100000000>; |
| fsl,num-tx-queues = <3>; |
| fsl,num-rx-queues = <3>; |
| status = "disabled"; |
| }; |
| |
| }; |
| |
| aips4: bus@32c00000 { |
| compatible = "fsl,aips-bus", "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0x32c00000 0x32c00000 0x400000>; |
| |
| usbotg1: usb@32e40000 { |
| compatible = "fsl,imx8mm-usb", "fsl,imx7d-usb"; |
| reg = <0x32e40000 0x200>; |
| interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MM_CLK_USB1_CTRL_ROOT>; |
| clock-names = "usb1_ctrl_root_clk"; |
| assigned-clocks = <&clk IMX8MM_CLK_USB_BUS>; |
| assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_500M>; |
| fsl,usbphy = <&usbphynop1>; |
| fsl,usbmisc = <&usbmisc1 0>; |
| status = "disabled"; |
| }; |
| |
| usbmisc1: usbmisc@32e40200 { |
| compatible = "fsl,imx8mm-usbmisc", "fsl,imx7d-usbmisc"; |
| #index-cells = <1>; |
| reg = <0x32e40200 0x200>; |
| }; |
| |
| usbotg2: usb@32e50000 { |
| compatible = "fsl,imx8mm-usb", "fsl,imx7d-usb"; |
| reg = <0x32e50000 0x200>; |
| interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clk IMX8MM_CLK_USB1_CTRL_ROOT>; |
| clock-names = "usb1_ctrl_root_clk"; |
| assigned-clocks = <&clk IMX8MM_CLK_USB_BUS>; |
| assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_500M>; |
| fsl,usbphy = <&usbphynop2>; |
| fsl,usbmisc = <&usbmisc2 0>; |
| status = "disabled"; |
| }; |
| |
| usbmisc2: usbmisc@32e50200 { |
| compatible = "fsl,imx8mm-usbmisc", "fsl,imx7d-usbmisc"; |
| #index-cells = <1>; |
| reg = <0x32e50200 0x200>; |
| }; |
| |
| }; |
| |
| dma_apbh: dma-controller@33000000 { |
| compatible = "fsl,imx7d-dma-apbh", "fsl,imx28-dma-apbh"; |
| reg = <0x33000000 0x2000>; |
| interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "gpmi0", "gpmi1", "gpmi2", "gpmi3"; |
| #dma-cells = <1>; |
| dma-channels = <4>; |
| clocks = <&clk IMX8MM_CLK_NAND_USDHC_BUS_RAWNAND_CLK>; |
| }; |
| |
| gpmi: nand-controller@33002000{ |
| compatible = "fsl,imx8mm-gpmi-nand", "fsl,imx7d-gpmi-nand"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0x33002000 0x2000>, <0x33004000 0x4000>; |
| reg-names = "gpmi-nand", "bch"; |
| interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "bch"; |
| clocks = <&clk IMX8MM_CLK_NAND_ROOT>, |
| <&clk IMX8MM_CLK_NAND_USDHC_BUS_RAWNAND_CLK>; |
| clock-names = "gpmi_io", "gpmi_bch_apb"; |
| dmas = <&dma_apbh 0>; |
| dma-names = "rx-tx"; |
| status = "disabled"; |
| }; |
| |
| gic: interrupt-controller@38800000 { |
| compatible = "arm,gic-v3"; |
| reg = <0x38800000 0x10000>, /* GIC Dist */ |
| <0x38880000 0xc0000>; /* GICR (RD_base + SGI_base) */ |
| #interrupt-cells = <3>; |
| interrupt-controller; |
| interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| ddr-pmu@3d800000 { |
| compatible = "fsl,imx8mm-ddr-pmu", "fsl,imx8m-ddr-pmu"; |
| reg = <0x3d800000 0x400000>; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| }; |
| }; |
