| // SPDX-License-Identifier: GPL-2.0-or-later |
| /* |
| * Copyright (C) 2008 Sascha Hauer, Pengutronix |
| */ |
| |
| #include <linux/types.h> |
| #include <linux/init.h> |
| #include <linux/dma-mapping.h> |
| #include <linux/platform_device.h> |
| #include <linux/mtd/physmap.h> |
| #include <linux/mtd/plat-ram.h> |
| #include <linux/memory.h> |
| #include <linux/gpio.h> |
| #include <linux/smsc911x.h> |
| #include <linux/interrupt.h> |
| #include <linux/i2c.h> |
| #include <linux/property.h> |
| #include <linux/delay.h> |
| #include <linux/spi/spi.h> |
| #include <linux/irq.h> |
| #include <linux/can/platform/sja1000.h> |
| #include <linux/usb/otg.h> |
| #include <linux/usb/ulpi.h> |
| #include <linux/gfp.h> |
| #include <linux/regulator/machine.h> |
| #include <linux/regulator/fixed.h> |
| |
| #include <asm/mach-types.h> |
| #include <asm/mach/arch.h> |
| #include <asm/mach/time.h> |
| #include <asm/mach/map.h> |
| |
| #include "common.h" |
| #include "devices-imx31.h" |
| #include "ehci.h" |
| #include "hardware.h" |
| #include "iomux-mx3.h" |
| #include "pcm037.h" |
| #include "ulpi.h" |
| |
| static enum pcm037_board_variant pcm037_instance = PCM037_PCM970; |
| |
| static int __init pcm037_variant_setup(char *str) |
| { |
| if (!strcmp("eet", str)) |
| pcm037_instance = PCM037_EET; |
| else if (strcmp("pcm970", str)) |
| pr_warn("Unknown pcm037 baseboard variant %s\n", str); |
| |
| return 1; |
| } |
| |
| /* Supported values: "pcm970" (default) and "eet" */ |
| __setup("pcm037_variant=", pcm037_variant_setup); |
| |
| enum pcm037_board_variant pcm037_variant(void) |
| { |
| return pcm037_instance; |
| } |
| |
| /* UART1 with RTS/CTS handshake signals */ |
| static unsigned int pcm037_uart1_handshake_pins[] = { |
| MX31_PIN_CTS1__CTS1, |
| MX31_PIN_RTS1__RTS1, |
| MX31_PIN_TXD1__TXD1, |
| MX31_PIN_RXD1__RXD1, |
| }; |
| |
| /* UART1 without RTS/CTS handshake signals */ |
| static unsigned int pcm037_uart1_pins[] = { |
| MX31_PIN_TXD1__TXD1, |
| MX31_PIN_RXD1__RXD1, |
| }; |
| |
| static unsigned int pcm037_pins[] = { |
| /* I2C */ |
| MX31_PIN_CSPI2_MOSI__SCL, |
| MX31_PIN_CSPI2_MISO__SDA, |
| MX31_PIN_CSPI2_SS2__I2C3_SDA, |
| MX31_PIN_CSPI2_SCLK__I2C3_SCL, |
| /* SDHC1 */ |
| MX31_PIN_SD1_DATA3__SD1_DATA3, |
| MX31_PIN_SD1_DATA2__SD1_DATA2, |
| MX31_PIN_SD1_DATA1__SD1_DATA1, |
| MX31_PIN_SD1_DATA0__SD1_DATA0, |
| MX31_PIN_SD1_CLK__SD1_CLK, |
| MX31_PIN_SD1_CMD__SD1_CMD, |
| IOMUX_MODE(MX31_PIN_SCK6, IOMUX_CONFIG_GPIO), /* card detect */ |
| IOMUX_MODE(MX31_PIN_SFS6, IOMUX_CONFIG_GPIO), /* write protect */ |
| /* SPI1 */ |
| MX31_PIN_CSPI1_MOSI__MOSI, |
| MX31_PIN_CSPI1_MISO__MISO, |
| MX31_PIN_CSPI1_SCLK__SCLK, |
| MX31_PIN_CSPI1_SPI_RDY__SPI_RDY, |
| MX31_PIN_CSPI1_SS0__SS0, |
| MX31_PIN_CSPI1_SS1__SS1, |
| MX31_PIN_CSPI1_SS2__SS2, |
| /* UART2 */ |
| MX31_PIN_TXD2__TXD2, |
| MX31_PIN_RXD2__RXD2, |
| MX31_PIN_CTS2__CTS2, |
| MX31_PIN_RTS2__RTS2, |
| /* UART3 */ |
| MX31_PIN_CSPI3_MOSI__RXD3, |
| MX31_PIN_CSPI3_MISO__TXD3, |
| MX31_PIN_CSPI3_SCLK__RTS3, |
| MX31_PIN_CSPI3_SPI_RDY__CTS3, |
| /* LAN9217 irq pin */ |
| IOMUX_MODE(MX31_PIN_GPIO3_1, IOMUX_CONFIG_GPIO), |
| /* Onewire */ |
| MX31_PIN_BATT_LINE__OWIRE, |
| /* Framebuffer */ |
| MX31_PIN_LD0__LD0, |
| MX31_PIN_LD1__LD1, |
| MX31_PIN_LD2__LD2, |
| MX31_PIN_LD3__LD3, |
| MX31_PIN_LD4__LD4, |
| MX31_PIN_LD5__LD5, |
| MX31_PIN_LD6__LD6, |
| MX31_PIN_LD7__LD7, |
| MX31_PIN_LD8__LD8, |
| MX31_PIN_LD9__LD9, |
| MX31_PIN_LD10__LD10, |
| MX31_PIN_LD11__LD11, |
| MX31_PIN_LD12__LD12, |
| MX31_PIN_LD13__LD13, |
| MX31_PIN_LD14__LD14, |
| MX31_PIN_LD15__LD15, |
| MX31_PIN_LD16__LD16, |
| MX31_PIN_LD17__LD17, |
| MX31_PIN_VSYNC3__VSYNC3, |
| MX31_PIN_HSYNC__HSYNC, |
| MX31_PIN_FPSHIFT__FPSHIFT, |
| MX31_PIN_DRDY0__DRDY0, |
| MX31_PIN_D3_REV__D3_REV, |
| MX31_PIN_CONTRAST__CONTRAST, |
| MX31_PIN_D3_SPL__D3_SPL, |
| MX31_PIN_D3_CLS__D3_CLS, |
| MX31_PIN_LCS0__GPIO3_23, |
| /* GPIO */ |
| IOMUX_MODE(MX31_PIN_ATA_DMACK, IOMUX_CONFIG_GPIO), |
| /* OTG */ |
| MX31_PIN_USBOTG_DATA0__USBOTG_DATA0, |
| MX31_PIN_USBOTG_DATA1__USBOTG_DATA1, |
| MX31_PIN_USBOTG_DATA2__USBOTG_DATA2, |
| MX31_PIN_USBOTG_DATA3__USBOTG_DATA3, |
| MX31_PIN_USBOTG_DATA4__USBOTG_DATA4, |
| MX31_PIN_USBOTG_DATA5__USBOTG_DATA5, |
| MX31_PIN_USBOTG_DATA6__USBOTG_DATA6, |
| MX31_PIN_USBOTG_DATA7__USBOTG_DATA7, |
| MX31_PIN_USBOTG_CLK__USBOTG_CLK, |
| MX31_PIN_USBOTG_DIR__USBOTG_DIR, |
| MX31_PIN_USBOTG_NXT__USBOTG_NXT, |
| MX31_PIN_USBOTG_STP__USBOTG_STP, |
| /* USB host 2 */ |
| IOMUX_MODE(MX31_PIN_USBH2_CLK, IOMUX_CONFIG_FUNC), |
| IOMUX_MODE(MX31_PIN_USBH2_DIR, IOMUX_CONFIG_FUNC), |
| IOMUX_MODE(MX31_PIN_USBH2_NXT, IOMUX_CONFIG_FUNC), |
| IOMUX_MODE(MX31_PIN_USBH2_STP, IOMUX_CONFIG_FUNC), |
| IOMUX_MODE(MX31_PIN_USBH2_DATA0, IOMUX_CONFIG_FUNC), |
| IOMUX_MODE(MX31_PIN_USBH2_DATA1, IOMUX_CONFIG_FUNC), |
| IOMUX_MODE(MX31_PIN_STXD3, IOMUX_CONFIG_FUNC), |
| IOMUX_MODE(MX31_PIN_SRXD3, IOMUX_CONFIG_FUNC), |
| IOMUX_MODE(MX31_PIN_SCK3, IOMUX_CONFIG_FUNC), |
| IOMUX_MODE(MX31_PIN_SFS3, IOMUX_CONFIG_FUNC), |
| IOMUX_MODE(MX31_PIN_STXD6, IOMUX_CONFIG_FUNC), |
| IOMUX_MODE(MX31_PIN_SRXD6, IOMUX_CONFIG_FUNC), |
| }; |
| |
| static struct physmap_flash_data pcm037_flash_data = { |
| .width = 2, |
| }; |
| |
| static struct resource pcm037_flash_resource = { |
| .start = 0xa0000000, |
| .end = 0xa1ffffff, |
| .flags = IORESOURCE_MEM, |
| }; |
| |
| static struct platform_device pcm037_flash = { |
| .name = "physmap-flash", |
| .id = 0, |
| .dev = { |
| .platform_data = &pcm037_flash_data, |
| }, |
| .resource = &pcm037_flash_resource, |
| .num_resources = 1, |
| }; |
| |
| static const struct imxuart_platform_data uart_pdata __initconst = { |
| .flags = IMXUART_HAVE_RTSCTS, |
| }; |
| |
| static struct resource smsc911x_resources[] = { |
| { |
| .start = MX31_CS1_BASE_ADDR + 0x300, |
| .end = MX31_CS1_BASE_ADDR + 0x300 + SZ_64K - 1, |
| .flags = IORESOURCE_MEM, |
| }, { |
| /* irq number is run-time assigned */ |
| .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL, |
| }, |
| }; |
| |
| static struct smsc911x_platform_config smsc911x_info = { |
| .flags = SMSC911X_USE_32BIT | SMSC911X_FORCE_INTERNAL_PHY | |
| SMSC911X_SAVE_MAC_ADDRESS, |
| .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW, |
| .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN, |
| .phy_interface = PHY_INTERFACE_MODE_MII, |
| }; |
| |
| static struct platform_device pcm037_eth = { |
| .name = "smsc911x", |
| .id = -1, |
| .num_resources = ARRAY_SIZE(smsc911x_resources), |
| .resource = smsc911x_resources, |
| .dev = { |
| .platform_data = &smsc911x_info, |
| }, |
| }; |
| |
| static struct platdata_mtd_ram pcm038_sram_data = { |
| .bankwidth = 2, |
| }; |
| |
| static struct resource pcm038_sram_resource = { |
| .start = MX31_CS4_BASE_ADDR, |
| .end = MX31_CS4_BASE_ADDR + 512 * 1024 - 1, |
| .flags = IORESOURCE_MEM, |
| }; |
| |
| static struct platform_device pcm037_sram_device = { |
| .name = "mtd-ram", |
| .id = 0, |
| .dev = { |
| .platform_data = &pcm038_sram_data, |
| }, |
| .num_resources = 1, |
| .resource = &pcm038_sram_resource, |
| }; |
| |
| static const struct mxc_nand_platform_data |
| pcm037_nand_board_info __initconst = { |
| .width = 1, |
| .hw_ecc = 1, |
| }; |
| |
| static const struct imxi2c_platform_data pcm037_i2c1_data __initconst = { |
| .bitrate = 100000, |
| }; |
| |
| static const struct imxi2c_platform_data pcm037_i2c2_data __initconst = { |
| .bitrate = 20000, |
| }; |
| |
| static const struct property_entry board_eeprom_properties[] = { |
| PROPERTY_ENTRY_U32("pagesize", 32), |
| { } |
| }; |
| |
| static struct i2c_board_info pcm037_i2c_devices[] = { |
| { |
| I2C_BOARD_INFO("24c32", 0x52), /* E0=0, E1=1, E2=0 */ |
| .properties = board_eeprom_properties, |
| }, { |
| I2C_BOARD_INFO("pcf8563", 0x51), |
| } |
| }; |
| |
| /* Not connected by default */ |
| #ifdef PCM970_SDHC_RW_SWITCH |
| static int pcm970_sdhc1_get_ro(struct device *dev) |
| { |
| return gpio_get_value(IOMUX_TO_GPIO(MX31_PIN_SFS6)); |
| } |
| #endif |
| |
| #define SDHC1_GPIO_WP IOMUX_TO_GPIO(MX31_PIN_SFS6) |
| #define SDHC1_GPIO_DET IOMUX_TO_GPIO(MX31_PIN_SCK6) |
| |
| static int pcm970_sdhc1_init(struct device *dev, irq_handler_t detect_irq, |
| void *data) |
| { |
| int ret; |
| |
| ret = gpio_request(SDHC1_GPIO_DET, "sdhc-detect"); |
| if (ret) |
| return ret; |
| |
| gpio_direction_input(SDHC1_GPIO_DET); |
| |
| #ifdef PCM970_SDHC_RW_SWITCH |
| ret = gpio_request(SDHC1_GPIO_WP, "sdhc-wp"); |
| if (ret) |
| goto err_gpio_free; |
| gpio_direction_input(SDHC1_GPIO_WP); |
| #endif |
| |
| ret = request_irq(gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_SCK6)), detect_irq, |
| IRQF_TRIGGER_FALLING, "sdhc-detect", data); |
| if (ret) |
| goto err_gpio_free_2; |
| |
| return 0; |
| |
| err_gpio_free_2: |
| #ifdef PCM970_SDHC_RW_SWITCH |
| gpio_free(SDHC1_GPIO_WP); |
| err_gpio_free: |
| #endif |
| gpio_free(SDHC1_GPIO_DET); |
| |
| return ret; |
| } |
| |
| static void pcm970_sdhc1_exit(struct device *dev, void *data) |
| { |
| free_irq(gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_SCK6)), data); |
| gpio_free(SDHC1_GPIO_DET); |
| gpio_free(SDHC1_GPIO_WP); |
| } |
| |
| static const struct imxmmc_platform_data sdhc_pdata __initconst = { |
| #ifdef PCM970_SDHC_RW_SWITCH |
| .get_ro = pcm970_sdhc1_get_ro, |
| #endif |
| .init = pcm970_sdhc1_init, |
| .exit = pcm970_sdhc1_exit, |
| }; |
| |
| static struct platform_device *devices[] __initdata = { |
| &pcm037_flash, |
| &pcm037_sram_device, |
| }; |
| |
| static const struct fb_videomode fb_modedb[] = { |
| { |
| /* 240x320 @ 60 Hz Sharp */ |
| .name = "Sharp-LQ035Q7DH06-QVGA", |
| .refresh = 60, |
| .xres = 240, |
| .yres = 320, |
| .pixclock = 185925, |
| .left_margin = 9, |
| .right_margin = 16, |
| .upper_margin = 7, |
| .lower_margin = 9, |
| .hsync_len = 1, |
| .vsync_len = 1, |
| .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_SHARP_MODE | |
| FB_SYNC_CLK_INVERT | FB_SYNC_CLK_IDLE_EN, |
| .vmode = FB_VMODE_NONINTERLACED, |
| .flag = 0, |
| }, { |
| /* 240x320 @ 60 Hz */ |
| .name = "TX090", |
| .refresh = 60, |
| .xres = 240, |
| .yres = 320, |
| .pixclock = 38255, |
| .left_margin = 144, |
| .right_margin = 0, |
| .upper_margin = 7, |
| .lower_margin = 40, |
| .hsync_len = 96, |
| .vsync_len = 1, |
| .sync = FB_SYNC_VERT_HIGH_ACT | FB_SYNC_OE_ACT_HIGH, |
| .vmode = FB_VMODE_NONINTERLACED, |
| .flag = 0, |
| }, { |
| /* 240x320 @ 60 Hz */ |
| .name = "CMEL-OLED", |
| .refresh = 60, |
| .xres = 240, |
| .yres = 320, |
| .pixclock = 185925, |
| .left_margin = 9, |
| .right_margin = 16, |
| .upper_margin = 7, |
| .lower_margin = 9, |
| .hsync_len = 1, |
| .vsync_len = 1, |
| .sync = FB_SYNC_OE_ACT_HIGH | FB_SYNC_CLK_INVERT, |
| .vmode = FB_VMODE_NONINTERLACED, |
| .flag = 0, |
| }, |
| }; |
| |
| static struct mx3fb_platform_data mx3fb_pdata = { |
| .name = "Sharp-LQ035Q7DH06-QVGA", |
| .mode = fb_modedb, |
| .num_modes = ARRAY_SIZE(fb_modedb), |
| }; |
| |
| static struct resource pcm970_sja1000_resources[] = { |
| { |
| .start = MX31_CS5_BASE_ADDR, |
| .end = MX31_CS5_BASE_ADDR + 0x100 - 1, |
| .flags = IORESOURCE_MEM, |
| }, { |
| /* irq number is run-time assigned */ |
| .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE, |
| }, |
| }; |
| |
| static struct sja1000_platform_data pcm970_sja1000_platform_data = { |
| .osc_freq = 16000000, |
| .ocr = OCR_TX1_PULLDOWN | OCR_TX0_PUSHPULL, |
| .cdr = CDR_CBP, |
| }; |
| |
| static struct platform_device pcm970_sja1000 = { |
| .name = "sja1000_platform", |
| .dev = { |
| .platform_data = &pcm970_sja1000_platform_data, |
| }, |
| .resource = pcm970_sja1000_resources, |
| .num_resources = ARRAY_SIZE(pcm970_sja1000_resources), |
| }; |
| |
| static int pcm037_otg_init(struct platform_device *pdev) |
| { |
| return mx31_initialize_usb_hw(pdev->id, MXC_EHCI_INTERFACE_DIFF_UNI); |
| } |
| |
| static struct mxc_usbh_platform_data otg_pdata __initdata = { |
| .init = pcm037_otg_init, |
| .portsc = MXC_EHCI_MODE_ULPI, |
| }; |
| |
| static int pcm037_usbh2_init(struct platform_device *pdev) |
| { |
| return mx31_initialize_usb_hw(pdev->id, MXC_EHCI_INTERFACE_DIFF_UNI); |
| } |
| |
| static struct mxc_usbh_platform_data usbh2_pdata __initdata = { |
| .init = pcm037_usbh2_init, |
| .portsc = MXC_EHCI_MODE_ULPI, |
| }; |
| |
| static const struct fsl_usb2_platform_data otg_device_pdata __initconst = { |
| .operating_mode = FSL_USB2_DR_DEVICE, |
| .phy_mode = FSL_USB2_PHY_ULPI, |
| }; |
| |
| static bool otg_mode_host __initdata; |
| |
| static int __init pcm037_otg_mode(char *options) |
| { |
| if (!strcmp(options, "host")) |
| otg_mode_host = true; |
| else if (!strcmp(options, "device")) |
| otg_mode_host = false; |
| else |
| pr_info("otg_mode neither \"host\" nor \"device\". " |
| "Defaulting to device\n"); |
| return 1; |
| } |
| __setup("otg_mode=", pcm037_otg_mode); |
| |
| static struct regulator_consumer_supply dummy_supplies[] = { |
| REGULATOR_SUPPLY("vdd33a", "smsc911x"), |
| REGULATOR_SUPPLY("vddvario", "smsc911x"), |
| }; |
| |
| /* |
| * Board specific initialization. |
| */ |
| static void __init pcm037_init(void) |
| { |
| imx31_soc_init(); |
| |
| regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies)); |
| |
| mxc_iomux_set_gpr(MUX_PGP_UH2, 1); |
| |
| mxc_iomux_setup_multiple_pins(pcm037_pins, ARRAY_SIZE(pcm037_pins), |
| "pcm037"); |
| |
| #define H2_PAD_CFG (PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST | PAD_CTL_HYS_CMOS \ |
| | PAD_CTL_ODE_CMOS | PAD_CTL_100K_PU) |
| |
| mxc_iomux_set_pad(MX31_PIN_USBH2_CLK, H2_PAD_CFG); |
| mxc_iomux_set_pad(MX31_PIN_USBH2_DIR, H2_PAD_CFG); |
| mxc_iomux_set_pad(MX31_PIN_USBH2_NXT, H2_PAD_CFG); |
| mxc_iomux_set_pad(MX31_PIN_USBH2_STP, H2_PAD_CFG); |
| mxc_iomux_set_pad(MX31_PIN_USBH2_DATA0, H2_PAD_CFG); /* USBH2_DATA0 */ |
| mxc_iomux_set_pad(MX31_PIN_USBH2_DATA1, H2_PAD_CFG); /* USBH2_DATA1 */ |
| mxc_iomux_set_pad(MX31_PIN_SRXD6, H2_PAD_CFG); /* USBH2_DATA2 */ |
| mxc_iomux_set_pad(MX31_PIN_STXD6, H2_PAD_CFG); /* USBH2_DATA3 */ |
| mxc_iomux_set_pad(MX31_PIN_SFS3, H2_PAD_CFG); /* USBH2_DATA4 */ |
| mxc_iomux_set_pad(MX31_PIN_SCK3, H2_PAD_CFG); /* USBH2_DATA5 */ |
| mxc_iomux_set_pad(MX31_PIN_SRXD3, H2_PAD_CFG); /* USBH2_DATA6 */ |
| mxc_iomux_set_pad(MX31_PIN_STXD3, H2_PAD_CFG); /* USBH2_DATA7 */ |
| |
| if (pcm037_variant() == PCM037_EET) |
| mxc_iomux_setup_multiple_pins(pcm037_uart1_pins, |
| ARRAY_SIZE(pcm037_uart1_pins), "pcm037_uart1"); |
| else |
| mxc_iomux_setup_multiple_pins(pcm037_uart1_handshake_pins, |
| ARRAY_SIZE(pcm037_uart1_handshake_pins), |
| "pcm037_uart1"); |
| |
| platform_add_devices(devices, ARRAY_SIZE(devices)); |
| |
| imx31_add_imx2_wdt(); |
| imx31_add_imx_uart0(&uart_pdata); |
| /* XXX: should't this have .flags = 0 (i.e. no RTSCTS) on PCM037_EET? */ |
| imx31_add_imx_uart1(&uart_pdata); |
| imx31_add_imx_uart2(&uart_pdata); |
| |
| imx31_add_mxc_w1(); |
| |
| /* I2C adapters and devices */ |
| i2c_register_board_info(1, pcm037_i2c_devices, |
| ARRAY_SIZE(pcm037_i2c_devices)); |
| |
| imx31_add_imx_i2c1(&pcm037_i2c1_data); |
| imx31_add_imx_i2c2(&pcm037_i2c2_data); |
| |
| imx31_add_mxc_nand(&pcm037_nand_board_info); |
| imx31_add_ipu_core(); |
| imx31_add_mx3_sdc_fb(&mx3fb_pdata); |
| |
| if (otg_mode_host) { |
| otg_pdata.otg = imx_otg_ulpi_create(ULPI_OTG_DRVVBUS | |
| ULPI_OTG_DRVVBUS_EXT); |
| if (otg_pdata.otg) |
| imx31_add_mxc_ehci_otg(&otg_pdata); |
| } |
| |
| usbh2_pdata.otg = imx_otg_ulpi_create(ULPI_OTG_DRVVBUS | |
| ULPI_OTG_DRVVBUS_EXT); |
| if (usbh2_pdata.otg) |
| imx31_add_mxc_ehci_hs(2, &usbh2_pdata); |
| |
| if (!otg_mode_host) |
| imx31_add_fsl_usb2_udc(&otg_device_pdata); |
| } |
| |
| static void __init pcm037_timer_init(void) |
| { |
| mx31_clocks_init(26000000); |
| } |
| |
| static void __init pcm037_init_late(void) |
| { |
| int ret; |
| |
| /* LAN9217 IRQ pin */ |
| ret = gpio_request(IOMUX_TO_GPIO(MX31_PIN_GPIO3_1), "lan9217-irq"); |
| if (!ret) { |
| gpio_direction_input(IOMUX_TO_GPIO(MX31_PIN_GPIO3_1)); |
| smsc911x_resources[1].start = |
| gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO3_1)); |
| smsc911x_resources[1].end = |
| gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO3_1)); |
| platform_device_register(&pcm037_eth); |
| } else { |
| pr_warn("could not get LAN irq gpio\n"); |
| } |
| |
| imx31_add_mxc_mmc(0, &sdhc_pdata); |
| |
| pcm970_sja1000_resources[1].start = |
| gpio_to_irq(IOMUX_TO_GPIO(IOMUX_PIN(48, 105))); |
| pcm970_sja1000_resources[1].end = |
| gpio_to_irq(IOMUX_TO_GPIO(IOMUX_PIN(48, 105))); |
| platform_device_register(&pcm970_sja1000); |
| |
| pcm037_eet_init_devices(); |
| } |
| |
| MACHINE_START(PCM037, "Phytec Phycore pcm037") |
| /* Maintainer: Pengutronix */ |
| .atag_offset = 0x100, |
| .map_io = mx31_map_io, |
| .init_early = imx31_init_early, |
| .init_irq = mx31_init_irq, |
| .init_time = pcm037_timer_init, |
| .init_machine = pcm037_init, |
| .init_late = pcm037_init_late, |
| .restart = mxc_restart, |
| MACHINE_END |