| // SPDX-License-Identifier: GPL-2.0-or-later |
| /* |
| * Driver for the NXP SAA7164 PCIe bridge |
| * |
| * Copyright (c) 2010-2015 Steven Toth <stoth@kernellabs.com> |
| */ |
| |
| #include <linux/wait.h> |
| #include <linux/slab.h> |
| |
| #include "saa7164.h" |
| |
| int saa7164_api_get_load_info(struct saa7164_dev *dev, struct tmFwInfoStruct *i) |
| { |
| int ret; |
| |
| if (!(saa_debug & DBGLVL_CPU)) |
| return 0; |
| |
| dprintk(DBGLVL_API, "%s()\n", __func__); |
| |
| i->deviceinst = 0; |
| i->devicespec = 0; |
| i->mode = 0; |
| i->status = 0; |
| |
| ret = saa7164_cmd_send(dev, 0, GET_CUR, |
| GET_FW_STATUS_CONTROL, sizeof(struct tmFwInfoStruct), i); |
| if (ret != SAA_OK) |
| printk(KERN_ERR "%s() error, ret = 0x%x\n", __func__, ret); |
| |
| printk(KERN_INFO "saa7164[%d]-CPU: %d percent", dev->nr, i->CPULoad); |
| |
| return ret; |
| } |
| |
| int saa7164_api_collect_debug(struct saa7164_dev *dev) |
| { |
| struct tmComResDebugGetData d; |
| u8 more = 255; |
| int ret; |
| |
| dprintk(DBGLVL_API, "%s()\n", __func__); |
| |
| while (more--) { |
| |
| memset(&d, 0, sizeof(d)); |
| |
| ret = saa7164_cmd_send(dev, 0, GET_CUR, |
| GET_DEBUG_DATA_CONTROL, sizeof(d), &d); |
| if (ret != SAA_OK) |
| printk(KERN_ERR "%s() error, ret = 0x%x\n", |
| __func__, ret); |
| |
| if (d.dwResult != SAA_OK) |
| break; |
| |
| printk(KERN_INFO "saa7164[%d]-FWMSG: %s", dev->nr, |
| d.ucDebugData); |
| } |
| |
| return 0; |
| } |
| |
| int saa7164_api_set_debug(struct saa7164_dev *dev, u8 level) |
| { |
| struct tmComResDebugSetLevel lvl; |
| int ret; |
| |
| dprintk(DBGLVL_API, "%s(level=%d)\n", __func__, level); |
| |
| /* Retrieve current state */ |
| ret = saa7164_cmd_send(dev, 0, GET_CUR, |
| SET_DEBUG_LEVEL_CONTROL, sizeof(lvl), &lvl); |
| if (ret != SAA_OK) |
| printk(KERN_ERR "%s() error, ret = 0x%x\n", __func__, ret); |
| |
| dprintk(DBGLVL_API, "%s() Was %d\n", __func__, lvl.dwDebugLevel); |
| |
| lvl.dwDebugLevel = level; |
| |
| /* set new state */ |
| ret = saa7164_cmd_send(dev, 0, SET_CUR, |
| SET_DEBUG_LEVEL_CONTROL, sizeof(lvl), &lvl); |
| if (ret != SAA_OK) |
| printk(KERN_ERR "%s() error, ret = 0x%x\n", __func__, ret); |
| |
| return ret; |
| } |
| |
| int saa7164_api_set_vbi_format(struct saa7164_port *port) |
| { |
| struct saa7164_dev *dev = port->dev; |
| struct tmComResProbeCommit fmt, rsp; |
| int ret; |
| |
| dprintk(DBGLVL_API, "%s(nr=%d, unitid=0x%x)\n", __func__, |
| port->nr, port->hwcfg.unitid); |
| |
| fmt.bmHint = 0; |
| fmt.bFormatIndex = 1; |
| fmt.bFrameIndex = 1; |
| |
| /* Probe, see if it can support this format */ |
| ret = saa7164_cmd_send(port->dev, port->hwcfg.unitid, |
| SET_CUR, SAA_PROBE_CONTROL, sizeof(fmt), &fmt); |
| if (ret != SAA_OK) |
| printk(KERN_ERR "%s() set error, ret = 0x%x\n", __func__, ret); |
| |
| /* See of the format change was successful */ |
| ret = saa7164_cmd_send(port->dev, port->hwcfg.unitid, |
| GET_CUR, SAA_PROBE_CONTROL, sizeof(rsp), &rsp); |
| if (ret != SAA_OK) { |
| printk(KERN_ERR "%s() get error, ret = 0x%x\n", __func__, ret); |
| } else { |
| /* Compare requested vs received, should be same */ |
| if (memcmp(&fmt, &rsp, sizeof(rsp)) == 0) { |
| dprintk(DBGLVL_API, "SET/PROBE Verified\n"); |
| |
| /* Ask the device to select the negotiated format */ |
| ret = saa7164_cmd_send(port->dev, port->hwcfg.unitid, |
| SET_CUR, SAA_COMMIT_CONTROL, sizeof(fmt), &fmt); |
| if (ret != SAA_OK) |
| printk(KERN_ERR "%s() commit error, ret = 0x%x\n", |
| __func__, ret); |
| |
| ret = saa7164_cmd_send(port->dev, port->hwcfg.unitid, |
| GET_CUR, SAA_COMMIT_CONTROL, sizeof(rsp), &rsp); |
| if (ret != SAA_OK) |
| printk(KERN_ERR "%s() GET commit error, ret = 0x%x\n", |
| __func__, ret); |
| |
| if (memcmp(&fmt, &rsp, sizeof(rsp)) != 0) { |
| printk(KERN_ERR "%s() memcmp error, ret = 0x%x\n", |
| __func__, ret); |
| } else |
| dprintk(DBGLVL_API, "SET/COMMIT Verified\n"); |
| |
| dprintk(DBGLVL_API, "rsp.bmHint = 0x%x\n", rsp.bmHint); |
| dprintk(DBGLVL_API, "rsp.bFormatIndex = 0x%x\n", |
| rsp.bFormatIndex); |
| dprintk(DBGLVL_API, "rsp.bFrameIndex = 0x%x\n", |
| rsp.bFrameIndex); |
| } else |
| printk(KERN_ERR "%s() compare failed\n", __func__); |
| } |
| |
| if (ret == SAA_OK) |
| dprintk(DBGLVL_API, "%s(nr=%d) Success\n", __func__, port->nr); |
| |
| return ret; |
| } |
| |
| static int saa7164_api_set_gop_size(struct saa7164_port *port) |
| { |
| struct saa7164_dev *dev = port->dev; |
| struct tmComResEncVideoGopStructure gs; |
| int ret; |
| |
| dprintk(DBGLVL_ENC, "%s()\n", __func__); |
| |
| gs.ucRefFrameDist = port->encoder_params.refdist; |
| gs.ucGOPSize = port->encoder_params.gop_size; |
| ret = saa7164_cmd_send(port->dev, port->hwcfg.sourceid, SET_CUR, |
| EU_VIDEO_GOP_STRUCTURE_CONTROL, |
| sizeof(gs), &gs); |
| if (ret != SAA_OK) |
| printk(KERN_ERR "%s() error, ret = 0x%x\n", __func__, ret); |
| |
| return ret; |
| } |
| |
| int saa7164_api_set_encoder(struct saa7164_port *port) |
| { |
| struct saa7164_dev *dev = port->dev; |
| struct tmComResEncVideoBitRate vb; |
| struct tmComResEncAudioBitRate ab; |
| int ret; |
| |
| dprintk(DBGLVL_ENC, "%s() unitid=0x%x\n", __func__, |
| port->hwcfg.sourceid); |
| |
| if (port->encoder_params.stream_type == V4L2_MPEG_STREAM_TYPE_MPEG2_PS) |
| port->encoder_profile = EU_PROFILE_PS_DVD; |
| else |
| port->encoder_profile = EU_PROFILE_TS_HQ; |
| |
| ret = saa7164_cmd_send(port->dev, port->hwcfg.sourceid, SET_CUR, |
| EU_PROFILE_CONTROL, sizeof(u8), &port->encoder_profile); |
| if (ret != SAA_OK) |
| printk(KERN_ERR "%s() error, ret = 0x%x\n", __func__, ret); |
| |
| /* Resolution */ |
| ret = saa7164_cmd_send(port->dev, port->hwcfg.sourceid, SET_CUR, |
| EU_PROFILE_CONTROL, sizeof(u8), &port->encoder_profile); |
| if (ret != SAA_OK) |
| printk(KERN_ERR "%s() error, ret = 0x%x\n", __func__, ret); |
| |
| /* Establish video bitrates */ |
| if (port->encoder_params.bitrate_mode == |
| V4L2_MPEG_VIDEO_BITRATE_MODE_CBR) |
| vb.ucVideoBitRateMode = EU_VIDEO_BIT_RATE_MODE_CONSTANT; |
| else |
| vb.ucVideoBitRateMode = EU_VIDEO_BIT_RATE_MODE_VARIABLE_PEAK; |
| vb.dwVideoBitRate = port->encoder_params.bitrate; |
| vb.dwVideoBitRatePeak = port->encoder_params.bitrate_peak; |
| ret = saa7164_cmd_send(port->dev, port->hwcfg.sourceid, SET_CUR, |
| EU_VIDEO_BIT_RATE_CONTROL, |
| sizeof(struct tmComResEncVideoBitRate), |
| &vb); |
| if (ret != SAA_OK) |
| printk(KERN_ERR "%s() error, ret = 0x%x\n", __func__, ret); |
| |
| /* Establish audio bitrates */ |
| ab.ucAudioBitRateMode = 0; |
| ab.dwAudioBitRate = 384000; |
| ab.dwAudioBitRatePeak = ab.dwAudioBitRate; |
| ret = saa7164_cmd_send(port->dev, port->hwcfg.sourceid, SET_CUR, |
| EU_AUDIO_BIT_RATE_CONTROL, |
| sizeof(struct tmComResEncAudioBitRate), |
| &ab); |
| if (ret != SAA_OK) |
| printk(KERN_ERR "%s() error, ret = 0x%x\n", __func__, |
| ret); |
| |
| saa7164_api_set_aspect_ratio(port); |
| saa7164_api_set_gop_size(port); |
| |
| return ret; |
| } |
| |
| int saa7164_api_get_encoder(struct saa7164_port *port) |
| { |
| struct saa7164_dev *dev = port->dev; |
| struct tmComResEncVideoBitRate v; |
| struct tmComResEncAudioBitRate a; |
| struct tmComResEncVideoInputAspectRatio ar; |
| int ret; |
| |
| dprintk(DBGLVL_ENC, "%s() unitid=0x%x\n", __func__, |
| port->hwcfg.sourceid); |
| |
| port->encoder_profile = 0; |
| port->video_format = 0; |
| port->video_resolution = 0; |
| port->audio_format = 0; |
| |
| ret = saa7164_cmd_send(port->dev, port->hwcfg.sourceid, GET_CUR, |
| EU_PROFILE_CONTROL, sizeof(u8), &port->encoder_profile); |
| if (ret != SAA_OK) |
| printk(KERN_ERR "%s() error, ret = 0x%x\n", __func__, ret); |
| |
| ret = saa7164_cmd_send(port->dev, port->hwcfg.sourceid, GET_CUR, |
| EU_VIDEO_RESOLUTION_CONTROL, sizeof(u8), |
| &port->video_resolution); |
| if (ret != SAA_OK) |
| printk(KERN_ERR "%s() error, ret = 0x%x\n", __func__, ret); |
| |
| ret = saa7164_cmd_send(port->dev, port->hwcfg.sourceid, GET_CUR, |
| EU_VIDEO_FORMAT_CONTROL, sizeof(u8), &port->video_format); |
| if (ret != SAA_OK) |
| printk(KERN_ERR "%s() error, ret = 0x%x\n", __func__, ret); |
| |
| ret = saa7164_cmd_send(port->dev, port->hwcfg.sourceid, GET_CUR, |
| EU_VIDEO_BIT_RATE_CONTROL, sizeof(v), &v); |
| if (ret != SAA_OK) |
| printk(KERN_ERR "%s() error, ret = 0x%x\n", __func__, ret); |
| |
| ret = saa7164_cmd_send(port->dev, port->hwcfg.sourceid, GET_CUR, |
| EU_AUDIO_FORMAT_CONTROL, sizeof(u8), &port->audio_format); |
| if (ret != SAA_OK) |
| printk(KERN_ERR "%s() error, ret = 0x%x\n", __func__, ret); |
| |
| ret = saa7164_cmd_send(port->dev, port->hwcfg.sourceid, GET_CUR, |
| EU_AUDIO_BIT_RATE_CONTROL, sizeof(a), &a); |
| if (ret != SAA_OK) |
| printk(KERN_ERR "%s() error, ret = 0x%x\n", __func__, ret); |
| |
| /* Aspect Ratio */ |
| ar.width = 0; |
| ar.height = 0; |
| ret = saa7164_cmd_send(port->dev, port->hwcfg.sourceid, GET_CUR, |
| EU_VIDEO_INPUT_ASPECT_CONTROL, |
| sizeof(struct tmComResEncVideoInputAspectRatio), &ar); |
| if (ret != SAA_OK) |
| printk(KERN_ERR "%s() error, ret = 0x%x\n", __func__, ret); |
| |
| dprintk(DBGLVL_ENC, "encoder_profile = %d\n", port->encoder_profile); |
| dprintk(DBGLVL_ENC, "video_format = %d\n", port->video_format); |
| dprintk(DBGLVL_ENC, "audio_format = %d\n", port->audio_format); |
| dprintk(DBGLVL_ENC, "video_resolution= %d\n", port->video_resolution); |
| dprintk(DBGLVL_ENC, "v.ucVideoBitRateMode = %d\n", |
| v.ucVideoBitRateMode); |
| dprintk(DBGLVL_ENC, "v.dwVideoBitRate = %d\n", |
| v.dwVideoBitRate); |
| dprintk(DBGLVL_ENC, "v.dwVideoBitRatePeak = %d\n", |
| v.dwVideoBitRatePeak); |
| dprintk(DBGLVL_ENC, "a.ucVideoBitRateMode = %d\n", |
| a.ucAudioBitRateMode); |
| dprintk(DBGLVL_ENC, "a.dwVideoBitRate = %d\n", |
| a.dwAudioBitRate); |
| dprintk(DBGLVL_ENC, "a.dwVideoBitRatePeak = %d\n", |
| a.dwAudioBitRatePeak); |
| dprintk(DBGLVL_ENC, "aspect.width / height = %d:%d\n", |
| ar.width, ar.height); |
| |
| return ret; |
| } |
| |
| int saa7164_api_set_aspect_ratio(struct saa7164_port *port) |
| { |
| struct saa7164_dev *dev = port->dev; |
| struct tmComResEncVideoInputAspectRatio ar; |
| int ret; |
| |
| dprintk(DBGLVL_ENC, "%s(%d)\n", __func__, |
| port->encoder_params.ctl_aspect); |
| |
| switch (port->encoder_params.ctl_aspect) { |
| case V4L2_MPEG_VIDEO_ASPECT_1x1: |
| ar.width = 1; |
| ar.height = 1; |
| break; |
| case V4L2_MPEG_VIDEO_ASPECT_4x3: |
| ar.width = 4; |
| ar.height = 3; |
| break; |
| case V4L2_MPEG_VIDEO_ASPECT_16x9: |
| ar.width = 16; |
| ar.height = 9; |
| break; |
| case V4L2_MPEG_VIDEO_ASPECT_221x100: |
| ar.width = 221; |
| ar.height = 100; |
| break; |
| default: |
| BUG(); |
| } |
| |
| dprintk(DBGLVL_ENC, "%s(%d) now %d:%d\n", __func__, |
| port->encoder_params.ctl_aspect, |
| ar.width, ar.height); |
| |
| /* Aspect Ratio */ |
| ret = saa7164_cmd_send(port->dev, port->hwcfg.sourceid, SET_CUR, |
| EU_VIDEO_INPUT_ASPECT_CONTROL, |
| sizeof(struct tmComResEncVideoInputAspectRatio), &ar); |
| if (ret != SAA_OK) |
| printk(KERN_ERR "%s() error, ret = 0x%x\n", __func__, ret); |
| |
| return ret; |
| } |
| |
| int saa7164_api_set_usercontrol(struct saa7164_port *port, u8 ctl) |
| { |
| struct saa7164_dev *dev = port->dev; |
| int ret; |
| u16 val; |
| |
| if (ctl == PU_BRIGHTNESS_CONTROL) |
| val = port->ctl_brightness; |
| else |
| if (ctl == PU_CONTRAST_CONTROL) |
| val = port->ctl_contrast; |
| else |
| if (ctl == PU_HUE_CONTROL) |
| val = port->ctl_hue; |
| else |
| if (ctl == PU_SATURATION_CONTROL) |
| val = port->ctl_saturation; |
| else |
| if (ctl == PU_SHARPNESS_CONTROL) |
| val = port->ctl_sharpness; |
| else |
| return -EINVAL; |
| |
| dprintk(DBGLVL_ENC, "%s() unitid=0x%x ctl=%d, val=%d\n", |
| __func__, port->encunit.vsourceid, ctl, val); |
| |
| ret = saa7164_cmd_send(port->dev, port->encunit.vsourceid, SET_CUR, |
| ctl, sizeof(u16), &val); |
| if (ret != SAA_OK) |
| printk(KERN_ERR "%s() error, ret = 0x%x\n", __func__, ret); |
| |
| return ret; |
| } |
| |
| int saa7164_api_get_usercontrol(struct saa7164_port *port, u8 ctl) |
| { |
| struct saa7164_dev *dev = port->dev; |
| int ret; |
| u16 val; |
| |
| ret = saa7164_cmd_send(port->dev, port->encunit.vsourceid, GET_CUR, |
| ctl, sizeof(u16), &val); |
| if (ret != SAA_OK) { |
| printk(KERN_ERR "%s() error, ret = 0x%x\n", __func__, ret); |
| return ret; |
| } |
| |
| dprintk(DBGLVL_ENC, "%s() ctl=%d, val=%d\n", |
| __func__, ctl, val); |
| |
| if (ctl == PU_BRIGHTNESS_CONTROL) |
| port->ctl_brightness = val; |
| else |
| if (ctl == PU_CONTRAST_CONTROL) |
| port->ctl_contrast = val; |
| else |
| if (ctl == PU_HUE_CONTROL) |
| port->ctl_hue = val; |
| else |
| if (ctl == PU_SATURATION_CONTROL) |
| port->ctl_saturation = val; |
| else |
| if (ctl == PU_SHARPNESS_CONTROL) |
| port->ctl_sharpness = val; |
| |
| return ret; |
| } |
| |
| int saa7164_api_set_videomux(struct saa7164_port *port) |
| { |
| struct saa7164_dev *dev = port->dev; |
| u8 inputs[] = { 1, 2, 2, 2, 5, 5, 5 }; |
| int ret; |
| |
| dprintk(DBGLVL_ENC, "%s() v_mux=%d a_mux=%d\n", |
| __func__, port->mux_input, inputs[port->mux_input - 1]); |
| |
| /* Audio Mute */ |
| ret = saa7164_api_audio_mute(port, 1); |
| if (ret != SAA_OK) |
| printk(KERN_ERR "%s() error, ret = 0x%x\n", __func__, ret); |
| |
| /* Video Mux */ |
| ret = saa7164_cmd_send(port->dev, port->vidproc.sourceid, SET_CUR, |
| SU_INPUT_SELECT_CONTROL, sizeof(u8), &port->mux_input); |
| if (ret != SAA_OK) |
| printk(KERN_ERR "%s() error, ret = 0x%x\n", __func__, ret); |
| |
| /* Audio Mux */ |
| ret = saa7164_cmd_send(port->dev, port->audfeat.sourceid, SET_CUR, |
| SU_INPUT_SELECT_CONTROL, sizeof(u8), |
| &inputs[port->mux_input - 1]); |
| if (ret != SAA_OK) |
| printk(KERN_ERR "%s() error, ret = 0x%x\n", __func__, ret); |
| |
| /* Audio UnMute */ |
| ret = saa7164_api_audio_mute(port, 0); |
| if (ret != SAA_OK) |
| printk(KERN_ERR "%s() error, ret = 0x%x\n", __func__, ret); |
| |
| return ret; |
| } |
| |
| int saa7164_api_audio_mute(struct saa7164_port *port, int mute) |
| { |
| struct saa7164_dev *dev = port->dev; |
| u8 v = mute; |
| int ret; |
| |
| dprintk(DBGLVL_API, "%s(%d)\n", __func__, mute); |
| |
| ret = saa7164_cmd_send(port->dev, port->audfeat.unitid, SET_CUR, |
| MUTE_CONTROL, sizeof(u8), &v); |
| if (ret != SAA_OK) |
| printk(KERN_ERR "%s() error, ret = 0x%x\n", __func__, ret); |
| |
| return ret; |
| } |
| |
| /* 0 = silence, 0xff = full */ |
| int saa7164_api_set_audio_volume(struct saa7164_port *port, s8 level) |
| { |
| struct saa7164_dev *dev = port->dev; |
| s16 v, min, max; |
| int ret; |
| |
| dprintk(DBGLVL_API, "%s(%d)\n", __func__, level); |
| |
| /* Obtain the min/max ranges */ |
| ret = saa7164_cmd_send(port->dev, port->audfeat.unitid, GET_MIN, |
| VOLUME_CONTROL, sizeof(u16), &min); |
| if (ret != SAA_OK) |
| printk(KERN_ERR "%s() error, ret = 0x%x\n", __func__, ret); |
| |
| ret = saa7164_cmd_send(port->dev, port->audfeat.unitid, GET_MAX, |
| VOLUME_CONTROL, sizeof(u16), &max); |
| if (ret != SAA_OK) |
| printk(KERN_ERR "%s() error, ret = 0x%x\n", __func__, ret); |
| |
| ret = saa7164_cmd_send(port->dev, port->audfeat.unitid, GET_CUR, |
| (0x01 << 8) | VOLUME_CONTROL, sizeof(u16), &v); |
| if (ret != SAA_OK) |
| printk(KERN_ERR "%s() error, ret = 0x%x\n", __func__, ret); |
| |
| dprintk(DBGLVL_API, "%s(%d) min=%d max=%d cur=%d\n", __func__, |
| level, min, max, v); |
| |
| v = level; |
| if (v < min) |
| v = min; |
| if (v > max) |
| v = max; |
| |
| /* Left */ |
| ret = saa7164_cmd_send(port->dev, port->audfeat.unitid, SET_CUR, |
| (0x01 << 8) | VOLUME_CONTROL, sizeof(s16), &v); |
| if (ret != SAA_OK) |
| printk(KERN_ERR "%s() error, ret = 0x%x\n", __func__, ret); |
| |
| /* Right */ |
| ret = saa7164_cmd_send(port->dev, port->audfeat.unitid, SET_CUR, |
| (0x02 << 8) | VOLUME_CONTROL, sizeof(s16), &v); |
| if (ret != SAA_OK) |
| printk(KERN_ERR "%s() error, ret = 0x%x\n", __func__, ret); |
| |
| ret = saa7164_cmd_send(port->dev, port->audfeat.unitid, GET_CUR, |
| (0x01 << 8) | VOLUME_CONTROL, sizeof(u16), &v); |
| if (ret != SAA_OK) |
| printk(KERN_ERR "%s() error, ret = 0x%x\n", __func__, ret); |
| |
| dprintk(DBGLVL_API, "%s(%d) min=%d max=%d cur=%d\n", __func__, |
| level, min, max, v); |
| |
| return ret; |
| } |
| |
| int saa7164_api_set_audio_std(struct saa7164_port *port) |
| { |
| struct saa7164_dev *dev = port->dev; |
| struct tmComResAudioDefaults lvl; |
| struct tmComResTunerStandard tvaudio; |
| int ret; |
| |
| dprintk(DBGLVL_API, "%s()\n", __func__); |
| |
| /* Establish default levels */ |
| lvl.ucDecoderLevel = TMHW_LEV_ADJ_DECLEV_DEFAULT; |
| lvl.ucDecoderFM_Level = TMHW_LEV_ADJ_DECLEV_DEFAULT; |
| lvl.ucMonoLevel = TMHW_LEV_ADJ_MONOLEV_DEFAULT; |
| lvl.ucNICAM_Level = TMHW_LEV_ADJ_NICLEV_DEFAULT; |
| lvl.ucSAP_Level = TMHW_LEV_ADJ_SAPLEV_DEFAULT; |
| lvl.ucADC_Level = TMHW_LEV_ADJ_ADCLEV_DEFAULT; |
| ret = saa7164_cmd_send(port->dev, port->audfeat.unitid, SET_CUR, |
| AUDIO_DEFAULT_CONTROL, sizeof(struct tmComResAudioDefaults), |
| &lvl); |
| if (ret != SAA_OK) |
| printk(KERN_ERR "%s() error, ret = 0x%x\n", __func__, ret); |
| |
| /* Manually select the appropriate TV audio standard */ |
| if (port->encodernorm.id & V4L2_STD_NTSC) { |
| tvaudio.std = TU_STANDARD_NTSC_M; |
| tvaudio.country = 1; |
| } else { |
| tvaudio.std = TU_STANDARD_PAL_I; |
| tvaudio.country = 44; |
| } |
| |
| ret = saa7164_cmd_send(port->dev, port->tunerunit.unitid, SET_CUR, |
| TU_STANDARD_CONTROL, sizeof(tvaudio), &tvaudio); |
| if (ret != SAA_OK) |
| printk(KERN_ERR "%s() TU_STANDARD_CONTROL error, ret = 0x%x\n", |
| __func__, ret); |
| return ret; |
| } |
| |
| int saa7164_api_set_audio_detection(struct saa7164_port *port, int autodetect) |
| { |
| struct saa7164_dev *dev = port->dev; |
| struct tmComResTunerStandardAuto p; |
| int ret; |
| |
| dprintk(DBGLVL_API, "%s(%d)\n", __func__, autodetect); |
| |
| /* Disable TV Audio autodetect if not already set (buggy) */ |
| if (autodetect) |
| p.mode = TU_STANDARD_AUTO; |
| else |
| p.mode = TU_STANDARD_MANUAL; |
| ret = saa7164_cmd_send(port->dev, port->tunerunit.unitid, SET_CUR, |
| TU_STANDARD_AUTO_CONTROL, sizeof(p), &p); |
| if (ret != SAA_OK) |
| printk(KERN_ERR |
| "%s() TU_STANDARD_AUTO_CONTROL error, ret = 0x%x\n", |
| __func__, ret); |
| |
| return ret; |
| } |
| |
| int saa7164_api_get_videomux(struct saa7164_port *port) |
| { |
| struct saa7164_dev *dev = port->dev; |
| int ret; |
| |
| ret = saa7164_cmd_send(port->dev, port->vidproc.sourceid, GET_CUR, |
| SU_INPUT_SELECT_CONTROL, sizeof(u8), &port->mux_input); |
| if (ret != SAA_OK) |
| printk(KERN_ERR "%s() error, ret = 0x%x\n", __func__, ret); |
| |
| dprintk(DBGLVL_ENC, "%s() v_mux=%d\n", |
| __func__, port->mux_input); |
| |
| return ret; |
| } |
| |
| static int saa7164_api_set_dif(struct saa7164_port *port, u8 reg, u8 val) |
| { |
| struct saa7164_dev *dev = port->dev; |
| |
| u16 len = 0; |
| u8 buf[256]; |
| int ret; |
| u8 mas; |
| |
| dprintk(DBGLVL_API, "%s(nr=%d type=%d val=%x)\n", __func__, |
| port->nr, port->type, val); |
| |
| if (port->nr == 0) |
| mas = 0xd0; |
| else |
| mas = 0xe0; |
| |
| memset(buf, 0, sizeof(buf)); |
| |
| buf[0x00] = 0x04; |
| buf[0x01] = 0x00; |
| buf[0x02] = 0x00; |
| buf[0x03] = 0x00; |
| |
| buf[0x04] = 0x04; |
| buf[0x05] = 0x00; |
| buf[0x06] = 0x00; |
| buf[0x07] = 0x00; |
| |
| buf[0x08] = reg; |
| buf[0x09] = 0x26; |
| buf[0x0a] = mas; |
| buf[0x0b] = 0xb0; |
| |
| buf[0x0c] = val; |
| buf[0x0d] = 0x00; |
| buf[0x0e] = 0x00; |
| buf[0x0f] = 0x00; |
| |
| ret = saa7164_cmd_send(dev, port->ifunit.unitid, GET_LEN, |
| EXU_REGISTER_ACCESS_CONTROL, sizeof(len), &len); |
| if (ret != SAA_OK) { |
| printk(KERN_ERR "%s() error, ret(1) = 0x%x\n", __func__, ret); |
| return -EIO; |
| } |
| |
| ret = saa7164_cmd_send(dev, port->ifunit.unitid, SET_CUR, |
| EXU_REGISTER_ACCESS_CONTROL, len, &buf); |
| if (ret != SAA_OK) |
| printk(KERN_ERR "%s() error, ret(2) = 0x%x\n", __func__, ret); |
| #if 0 |
| print_hex_dump(KERN_INFO, "", DUMP_PREFIX_OFFSET, 16, 1, buf, 16, |
| false); |
| #endif |
| return ret == SAA_OK ? 0 : -EIO; |
| } |
| |
| /* Disable the IF block AGC controls */ |
| int saa7164_api_configure_dif(struct saa7164_port *port, u32 std) |
| { |
| struct saa7164_dev *dev = port->dev; |
| u8 agc_disable; |
| |
| dprintk(DBGLVL_API, "%s(nr=%d, 0x%x)\n", __func__, port->nr, std); |
| |
| if (std & V4L2_STD_NTSC) { |
| dprintk(DBGLVL_API, " NTSC\n"); |
| saa7164_api_set_dif(port, 0x00, 0x01); /* Video Standard */ |
| agc_disable = 0; |
| } else if (std & V4L2_STD_PAL_I) { |
| dprintk(DBGLVL_API, " PAL-I\n"); |
| saa7164_api_set_dif(port, 0x00, 0x08); /* Video Standard */ |
| agc_disable = 0; |
| } else if (std & V4L2_STD_PAL_M) { |
| dprintk(DBGLVL_API, " PAL-M\n"); |
| saa7164_api_set_dif(port, 0x00, 0x01); /* Video Standard */ |
| agc_disable = 0; |
| } else if (std & V4L2_STD_PAL_N) { |
| dprintk(DBGLVL_API, " PAL-N\n"); |
| saa7164_api_set_dif(port, 0x00, 0x01); /* Video Standard */ |
| agc_disable = 0; |
| } else if (std & V4L2_STD_PAL_Nc) { |
| dprintk(DBGLVL_API, " PAL-Nc\n"); |
| saa7164_api_set_dif(port, 0x00, 0x01); /* Video Standard */ |
| agc_disable = 0; |
| } else if (std & V4L2_STD_PAL_B) { |
| dprintk(DBGLVL_API, " PAL-B\n"); |
| saa7164_api_set_dif(port, 0x00, 0x02); /* Video Standard */ |
| agc_disable = 0; |
| } else if (std & V4L2_STD_PAL_DK) { |
| dprintk(DBGLVL_API, " PAL-DK\n"); |
| saa7164_api_set_dif(port, 0x00, 0x10); /* Video Standard */ |
| agc_disable = 0; |
| } else if (std & V4L2_STD_SECAM_L) { |
| dprintk(DBGLVL_API, " SECAM-L\n"); |
| saa7164_api_set_dif(port, 0x00, 0x20); /* Video Standard */ |
| agc_disable = 0; |
| } else { |
| /* Unknown standard, assume DTV */ |
| dprintk(DBGLVL_API, " Unknown (assuming DTV)\n"); |
| /* Undefinded Video Standard */ |
| saa7164_api_set_dif(port, 0x00, 0x80); |
| agc_disable = 1; |
| } |
| |
| saa7164_api_set_dif(port, 0x48, 0xa0); /* AGC Functions 1 */ |
| saa7164_api_set_dif(port, 0xc0, agc_disable); /* AGC Output Disable */ |
| saa7164_api_set_dif(port, 0x7c, 0x04); /* CVBS EQ */ |
| saa7164_api_set_dif(port, 0x04, 0x01); /* Active */ |
| msleep(100); |
| saa7164_api_set_dif(port, 0x04, 0x00); /* Active (again) */ |
| msleep(100); |
| |
| return 0; |
| } |
| |
| /* Ensure the dif is in the correct state for the operating mode |
| * (analog / dtv). We only configure the diff through the analog encoder |
| * so when we're in digital mode we need to find the appropriate encoder |
| * and use it to configure the DIF. |
| */ |
| int saa7164_api_initialize_dif(struct saa7164_port *port) |
| { |
| struct saa7164_dev *dev = port->dev; |
| struct saa7164_port *p = NULL; |
| int ret = -EINVAL; |
| u32 std = 0; |
| |
| dprintk(DBGLVL_API, "%s(nr=%d type=%d)\n", __func__, |
| port->nr, port->type); |
| |
| if (port->type == SAA7164_MPEG_ENCODER) { |
| /* Pick any analog standard to init the diff. |
| * we'll come back during encoder_init' |
| * and set the correct standard if required. |
| */ |
| std = V4L2_STD_NTSC; |
| } else |
| if (port->type == SAA7164_MPEG_DVB) { |
| if (port->nr == SAA7164_PORT_TS1) |
| p = &dev->ports[SAA7164_PORT_ENC1]; |
| else |
| p = &dev->ports[SAA7164_PORT_ENC2]; |
| } else |
| if (port->type == SAA7164_MPEG_VBI) { |
| std = V4L2_STD_NTSC; |
| if (port->nr == SAA7164_PORT_VBI1) |
| p = &dev->ports[SAA7164_PORT_ENC1]; |
| else |
| p = &dev->ports[SAA7164_PORT_ENC2]; |
| } else |
| BUG(); |
| |
| if (p) |
| ret = saa7164_api_configure_dif(p, std); |
| |
| return ret; |
| } |
| |
| int saa7164_api_transition_port(struct saa7164_port *port, u8 mode) |
| { |
| struct saa7164_dev *dev = port->dev; |
| |
| int ret; |
| |
| dprintk(DBGLVL_API, "%s(nr=%d unitid=0x%x,%d)\n", |
| __func__, port->nr, port->hwcfg.unitid, mode); |
| |
| ret = saa7164_cmd_send(port->dev, port->hwcfg.unitid, SET_CUR, |
| SAA_STATE_CONTROL, sizeof(mode), &mode); |
| if (ret != SAA_OK) |
| printk(KERN_ERR "%s(portnr %d unitid 0x%x) error, ret = 0x%x\n", |
| __func__, port->nr, port->hwcfg.unitid, ret); |
| |
| return ret; |
| } |
| |
| int saa7164_api_get_fw_version(struct saa7164_dev *dev, u32 *version) |
| { |
| int ret; |
| |
| ret = saa7164_cmd_send(dev, 0, GET_CUR, |
| GET_FW_VERSION_CONTROL, sizeof(u32), version); |
| if (ret != SAA_OK) |
| printk(KERN_ERR "%s() error, ret = 0x%x\n", __func__, ret); |
| |
| return ret; |
| } |
| |
| int saa7164_api_read_eeprom(struct saa7164_dev *dev, u8 *buf, int buflen) |
| { |
| u8 reg[] = { 0x0f, 0x00 }; |
| |
| if (buflen < 128) |
| return -ENOMEM; |
| |
| /* Assumption: Hauppauge eeprom is at 0xa0 on on bus 0 */ |
| /* TODO: Pull the details from the boards struct */ |
| return saa7164_api_i2c_read(&dev->i2c_bus[0], 0xa0 >> 1, sizeof(reg), |
| ®[0], 128, buf); |
| } |
| |
| static int saa7164_api_configure_port_vbi(struct saa7164_dev *dev, |
| struct saa7164_port *port) |
| { |
| struct tmComResVBIFormatDescrHeader *fmt = &port->vbi_fmt_ntsc; |
| |
| dprintk(DBGLVL_API, " bFormatIndex = 0x%x\n", fmt->bFormatIndex); |
| dprintk(DBGLVL_API, " VideoStandard = 0x%x\n", fmt->VideoStandard); |
| dprintk(DBGLVL_API, " StartLine = %d\n", fmt->StartLine); |
| dprintk(DBGLVL_API, " EndLine = %d\n", fmt->EndLine); |
| dprintk(DBGLVL_API, " FieldRate = %d\n", fmt->FieldRate); |
| dprintk(DBGLVL_API, " bNumLines = %d\n", fmt->bNumLines); |
| |
| /* Cache the hardware configuration in the port */ |
| |
| port->bufcounter = port->hwcfg.BARLocation; |
| port->pitch = port->hwcfg.BARLocation + (2 * sizeof(u32)); |
| port->bufsize = port->hwcfg.BARLocation + (3 * sizeof(u32)); |
| port->bufoffset = port->hwcfg.BARLocation + (4 * sizeof(u32)); |
| port->bufptr32l = port->hwcfg.BARLocation + |
| (4 * sizeof(u32)) + |
| (sizeof(u32) * port->hwcfg.buffercount) + sizeof(u32); |
| port->bufptr32h = port->hwcfg.BARLocation + |
| (4 * sizeof(u32)) + |
| (sizeof(u32) * port->hwcfg.buffercount); |
| port->bufptr64 = port->hwcfg.BARLocation + |
| (4 * sizeof(u32)) + |
| (sizeof(u32) * port->hwcfg.buffercount); |
| dprintk(DBGLVL_API, " = port->hwcfg.BARLocation = 0x%x\n", |
| port->hwcfg.BARLocation); |
| |
| dprintk(DBGLVL_API, " = VS_FORMAT_VBI (becomes dev->en[%d])\n", |
| port->nr); |
| |
| return 0; |
| } |
| |
| static int |
| saa7164_api_configure_port_mpeg2ts(struct saa7164_dev *dev, |
| struct saa7164_port *port, |
| struct tmComResTSFormatDescrHeader *tsfmt) |
| { |
| dprintk(DBGLVL_API, " bFormatIndex = 0x%x\n", tsfmt->bFormatIndex); |
| dprintk(DBGLVL_API, " bDataOffset = 0x%x\n", tsfmt->bDataOffset); |
| dprintk(DBGLVL_API, " bPacketLength= 0x%x\n", tsfmt->bPacketLength); |
| dprintk(DBGLVL_API, " bStrideLength= 0x%x\n", tsfmt->bStrideLength); |
| dprintk(DBGLVL_API, " bguid = (....)\n"); |
| |
| /* Cache the hardware configuration in the port */ |
| |
| port->bufcounter = port->hwcfg.BARLocation; |
| port->pitch = port->hwcfg.BARLocation + (2 * sizeof(u32)); |
| port->bufsize = port->hwcfg.BARLocation + (3 * sizeof(u32)); |
| port->bufoffset = port->hwcfg.BARLocation + (4 * sizeof(u32)); |
| port->bufptr32l = port->hwcfg.BARLocation + |
| (4 * sizeof(u32)) + |
| (sizeof(u32) * port->hwcfg.buffercount) + sizeof(u32); |
| port->bufptr32h = port->hwcfg.BARLocation + |
| (4 * sizeof(u32)) + |
| (sizeof(u32) * port->hwcfg.buffercount); |
| port->bufptr64 = port->hwcfg.BARLocation + |
| (4 * sizeof(u32)) + |
| (sizeof(u32) * port->hwcfg.buffercount); |
| dprintk(DBGLVL_API, " = port->hwcfg.BARLocation = 0x%x\n", |
| port->hwcfg.BARLocation); |
| |
| dprintk(DBGLVL_API, " = VS_FORMAT_MPEGTS (becomes dev->ts[%d])\n", |
| port->nr); |
| |
| return 0; |
| } |
| |
| static int |
| saa7164_api_configure_port_mpeg2ps(struct saa7164_dev *dev, |
| struct saa7164_port *port, |
| struct tmComResPSFormatDescrHeader *fmt) |
| { |
| dprintk(DBGLVL_API, " bFormatIndex = 0x%x\n", fmt->bFormatIndex); |
| dprintk(DBGLVL_API, " wPacketLength= 0x%x\n", fmt->wPacketLength); |
| dprintk(DBGLVL_API, " wPackLength= 0x%x\n", fmt->wPackLength); |
| dprintk(DBGLVL_API, " bPackDataType= 0x%x\n", fmt->bPackDataType); |
| |
| /* Cache the hardware configuration in the port */ |
| /* TODO: CHECK THIS in the port config */ |
| port->bufcounter = port->hwcfg.BARLocation; |
| port->pitch = port->hwcfg.BARLocation + (2 * sizeof(u32)); |
| port->bufsize = port->hwcfg.BARLocation + (3 * sizeof(u32)); |
| port->bufoffset = port->hwcfg.BARLocation + (4 * sizeof(u32)); |
| port->bufptr32l = port->hwcfg.BARLocation + |
| (4 * sizeof(u32)) + |
| (sizeof(u32) * port->hwcfg.buffercount) + sizeof(u32); |
| port->bufptr32h = port->hwcfg.BARLocation + |
| (4 * sizeof(u32)) + |
| (sizeof(u32) * port->hwcfg.buffercount); |
| port->bufptr64 = port->hwcfg.BARLocation + |
| (4 * sizeof(u32)) + |
| (sizeof(u32) * port->hwcfg.buffercount); |
| dprintk(DBGLVL_API, " = port->hwcfg.BARLocation = 0x%x\n", |
| port->hwcfg.BARLocation); |
| |
| dprintk(DBGLVL_API, " = VS_FORMAT_MPEGPS (becomes dev->enc[%d])\n", |
| port->nr); |
| |
| return 0; |
| } |
| |
| static int saa7164_api_dump_subdevs(struct saa7164_dev *dev, u8 *buf, int len) |
| { |
| struct saa7164_port *tsport = NULL; |
| struct saa7164_port *encport = NULL; |
| struct saa7164_port *vbiport = NULL; |
| u32 idx, next_offset; |
| int i; |
| struct tmComResDescrHeader *hdr, *t; |
| struct tmComResExtDevDescrHeader *exthdr; |
| struct tmComResPathDescrHeader *pathhdr; |
| struct tmComResAntTermDescrHeader *anttermhdr; |
| struct tmComResTunerDescrHeader *tunerunithdr; |
| struct tmComResDMATermDescrHeader *vcoutputtermhdr; |
| struct tmComResTSFormatDescrHeader *tsfmt; |
| struct tmComResPSFormatDescrHeader *psfmt; |
| struct tmComResSelDescrHeader *psel; |
| struct tmComResProcDescrHeader *pdh; |
| struct tmComResAFeatureDescrHeader *afd; |
| struct tmComResEncoderDescrHeader *edh; |
| struct tmComResVBIFormatDescrHeader *vbifmt; |
| u32 currpath = 0; |
| |
| dprintk(DBGLVL_API, |
| "%s(?,?,%d) sizeof(struct tmComResDescrHeader) = %d bytes\n", |
| __func__, len, (u32)sizeof(struct tmComResDescrHeader)); |
| |
| for (idx = 0; idx < (len - sizeof(struct tmComResDescrHeader));) { |
| |
| hdr = (struct tmComResDescrHeader *)(buf + idx); |
| |
| if (hdr->type != CS_INTERFACE) |
| return SAA_ERR_NOT_SUPPORTED; |
| |
| dprintk(DBGLVL_API, "@ 0x%x =\n", idx); |
| switch (hdr->subtype) { |
| case GENERAL_REQUEST: |
| dprintk(DBGLVL_API, " GENERAL_REQUEST\n"); |
| break; |
| case VC_TUNER_PATH: |
| dprintk(DBGLVL_API, " VC_TUNER_PATH\n"); |
| pathhdr = (struct tmComResPathDescrHeader *)(buf + idx); |
| dprintk(DBGLVL_API, " pathid = 0x%x\n", |
| pathhdr->pathid); |
| currpath = pathhdr->pathid; |
| break; |
| case VC_INPUT_TERMINAL: |
| dprintk(DBGLVL_API, " VC_INPUT_TERMINAL\n"); |
| anttermhdr = |
| (struct tmComResAntTermDescrHeader *)(buf + idx); |
| dprintk(DBGLVL_API, " terminalid = 0x%x\n", |
| anttermhdr->terminalid); |
| dprintk(DBGLVL_API, " terminaltype = 0x%x\n", |
| anttermhdr->terminaltype); |
| switch (anttermhdr->terminaltype) { |
| case ITT_ANTENNA: |
| dprintk(DBGLVL_API, " = ITT_ANTENNA\n"); |
| break; |
| case LINE_CONNECTOR: |
| dprintk(DBGLVL_API, " = LINE_CONNECTOR\n"); |
| break; |
| case SPDIF_CONNECTOR: |
| dprintk(DBGLVL_API, " = SPDIF_CONNECTOR\n"); |
| break; |
| case COMPOSITE_CONNECTOR: |
| dprintk(DBGLVL_API, |
| " = COMPOSITE_CONNECTOR\n"); |
| break; |
| case SVIDEO_CONNECTOR: |
| dprintk(DBGLVL_API, " = SVIDEO_CONNECTOR\n"); |
| break; |
| case COMPONENT_CONNECTOR: |
| dprintk(DBGLVL_API, |
| " = COMPONENT_CONNECTOR\n"); |
| break; |
| case STANDARD_DMA: |
| dprintk(DBGLVL_API, " = STANDARD_DMA\n"); |
| break; |
| default: |
| dprintk(DBGLVL_API, " = undefined (0x%x)\n", |
| anttermhdr->terminaltype); |
| } |
| dprintk(DBGLVL_API, " assocterminal= 0x%x\n", |
| anttermhdr->assocterminal); |
| dprintk(DBGLVL_API, " iterminal = 0x%x\n", |
| anttermhdr->iterminal); |
| dprintk(DBGLVL_API, " controlsize = 0x%x\n", |
| anttermhdr->controlsize); |
| break; |
| case VC_OUTPUT_TERMINAL: |
| dprintk(DBGLVL_API, " VC_OUTPUT_TERMINAL\n"); |
| vcoutputtermhdr = |
| (struct tmComResDMATermDescrHeader *)(buf + idx); |
| dprintk(DBGLVL_API, " unitid = 0x%x\n", |
| vcoutputtermhdr->unitid); |
| dprintk(DBGLVL_API, " terminaltype = 0x%x\n", |
| vcoutputtermhdr->terminaltype); |
| switch (vcoutputtermhdr->terminaltype) { |
| case ITT_ANTENNA: |
| dprintk(DBGLVL_API, " = ITT_ANTENNA\n"); |
| break; |
| case LINE_CONNECTOR: |
| dprintk(DBGLVL_API, " = LINE_CONNECTOR\n"); |
| break; |
| case SPDIF_CONNECTOR: |
| dprintk(DBGLVL_API, " = SPDIF_CONNECTOR\n"); |
| break; |
| case COMPOSITE_CONNECTOR: |
| dprintk(DBGLVL_API, |
| " = COMPOSITE_CONNECTOR\n"); |
| break; |
| case SVIDEO_CONNECTOR: |
| dprintk(DBGLVL_API, " = SVIDEO_CONNECTOR\n"); |
| break; |
| case COMPONENT_CONNECTOR: |
| dprintk(DBGLVL_API, |
| " = COMPONENT_CONNECTOR\n"); |
| break; |
| case STANDARD_DMA: |
| dprintk(DBGLVL_API, " = STANDARD_DMA\n"); |
| break; |
| default: |
| dprintk(DBGLVL_API, " = undefined (0x%x)\n", |
| vcoutputtermhdr->terminaltype); |
| } |
| dprintk(DBGLVL_API, " assocterminal= 0x%x\n", |
| vcoutputtermhdr->assocterminal); |
| dprintk(DBGLVL_API, " sourceid = 0x%x\n", |
| vcoutputtermhdr->sourceid); |
| dprintk(DBGLVL_API, " iterminal = 0x%x\n", |
| vcoutputtermhdr->iterminal); |
| dprintk(DBGLVL_API, " BARLocation = 0x%x\n", |
| vcoutputtermhdr->BARLocation); |
| dprintk(DBGLVL_API, " flags = 0x%x\n", |
| vcoutputtermhdr->flags); |
| dprintk(DBGLVL_API, " interruptid = 0x%x\n", |
| vcoutputtermhdr->interruptid); |
| dprintk(DBGLVL_API, " buffercount = 0x%x\n", |
| vcoutputtermhdr->buffercount); |
| dprintk(DBGLVL_API, " metadatasize = 0x%x\n", |
| vcoutputtermhdr->metadatasize); |
| dprintk(DBGLVL_API, " controlsize = 0x%x\n", |
| vcoutputtermhdr->controlsize); |
| dprintk(DBGLVL_API, " numformats = 0x%x\n", |
| vcoutputtermhdr->numformats); |
| |
| next_offset = idx + (vcoutputtermhdr->len); |
| for (i = 0; i < vcoutputtermhdr->numformats; i++) { |
| t = (struct tmComResDescrHeader *) |
| (buf + next_offset); |
| switch (t->subtype) { |
| case VS_FORMAT_MPEG2TS: |
| tsfmt = |
| (struct tmComResTSFormatDescrHeader *)t; |
| if (currpath == 1) |
| tsport = &dev->ports[SAA7164_PORT_TS1]; |
| else |
| tsport = &dev->ports[SAA7164_PORT_TS2]; |
| memcpy(&tsport->hwcfg, vcoutputtermhdr, |
| sizeof(*vcoutputtermhdr)); |
| saa7164_api_configure_port_mpeg2ts(dev, |
| tsport, tsfmt); |
| break; |
| case VS_FORMAT_MPEG2PS: |
| psfmt = |
| (struct tmComResPSFormatDescrHeader *)t; |
| if (currpath == 1) |
| encport = &dev->ports[SAA7164_PORT_ENC1]; |
| else |
| encport = &dev->ports[SAA7164_PORT_ENC2]; |
| memcpy(&encport->hwcfg, vcoutputtermhdr, |
| sizeof(*vcoutputtermhdr)); |
| saa7164_api_configure_port_mpeg2ps(dev, |
| encport, psfmt); |
| break; |
| case VS_FORMAT_VBI: |
| vbifmt = |
| (struct tmComResVBIFormatDescrHeader *)t; |
| if (currpath == 1) |
| vbiport = &dev->ports[SAA7164_PORT_VBI1]; |
| else |
| vbiport = &dev->ports[SAA7164_PORT_VBI2]; |
| memcpy(&vbiport->hwcfg, vcoutputtermhdr, |
| sizeof(*vcoutputtermhdr)); |
| memcpy(&vbiport->vbi_fmt_ntsc, vbifmt, |
| sizeof(*vbifmt)); |
| saa7164_api_configure_port_vbi(dev, |
| vbiport); |
| break; |
| case VS_FORMAT_RDS: |
| dprintk(DBGLVL_API, |
| " = VS_FORMAT_RDS\n"); |
| break; |
| case VS_FORMAT_UNCOMPRESSED: |
| dprintk(DBGLVL_API, |
| " = VS_FORMAT_UNCOMPRESSED\n"); |
| break; |
| case VS_FORMAT_TYPE: |
| dprintk(DBGLVL_API, |
| " = VS_FORMAT_TYPE\n"); |
| break; |
| default: |
| dprintk(DBGLVL_API, |
| " = undefined (0x%x)\n", |
| t->subtype); |
| } |
| next_offset += t->len; |
| } |
| |
| break; |
| case TUNER_UNIT: |
| dprintk(DBGLVL_API, " TUNER_UNIT\n"); |
| tunerunithdr = |
| (struct tmComResTunerDescrHeader *)(buf + idx); |
| dprintk(DBGLVL_API, " unitid = 0x%x\n", |
| tunerunithdr->unitid); |
| dprintk(DBGLVL_API, " sourceid = 0x%x\n", |
| tunerunithdr->sourceid); |
| dprintk(DBGLVL_API, " iunit = 0x%x\n", |
| tunerunithdr->iunit); |
| dprintk(DBGLVL_API, " tuningstandards = 0x%x\n", |
| tunerunithdr->tuningstandards); |
| dprintk(DBGLVL_API, " controlsize = 0x%x\n", |
| tunerunithdr->controlsize); |
| dprintk(DBGLVL_API, " controls = 0x%x\n", |
| tunerunithdr->controls); |
| |
| if (tunerunithdr->unitid == tunerunithdr->iunit) { |
| if (currpath == 1) |
| encport = &dev->ports[SAA7164_PORT_ENC1]; |
| else |
| encport = &dev->ports[SAA7164_PORT_ENC2]; |
| memcpy(&encport->tunerunit, tunerunithdr, |
| sizeof(struct tmComResTunerDescrHeader)); |
| dprintk(DBGLVL_API, |
| " (becomes dev->enc[%d] tuner)\n", |
| encport->nr); |
| } |
| break; |
| case VC_SELECTOR_UNIT: |
| psel = (struct tmComResSelDescrHeader *)(buf + idx); |
| dprintk(DBGLVL_API, " VC_SELECTOR_UNIT\n"); |
| dprintk(DBGLVL_API, " unitid = 0x%x\n", |
| psel->unitid); |
| dprintk(DBGLVL_API, " nrinpins = 0x%x\n", |
| psel->nrinpins); |
| dprintk(DBGLVL_API, " sourceid = 0x%x\n", |
| psel->sourceid); |
| break; |
| case VC_PROCESSING_UNIT: |
| pdh = (struct tmComResProcDescrHeader *)(buf + idx); |
| dprintk(DBGLVL_API, " VC_PROCESSING_UNIT\n"); |
| dprintk(DBGLVL_API, " unitid = 0x%x\n", |
| pdh->unitid); |
| dprintk(DBGLVL_API, " sourceid = 0x%x\n", |
| pdh->sourceid); |
| dprintk(DBGLVL_API, " controlsize = 0x%x\n", |
| pdh->controlsize); |
| if (pdh->controlsize == 0x04) { |
| if (currpath == 1) |
| encport = &dev->ports[SAA7164_PORT_ENC1]; |
| else |
| encport = &dev->ports[SAA7164_PORT_ENC2]; |
| memcpy(&encport->vidproc, pdh, |
| sizeof(struct tmComResProcDescrHeader)); |
| dprintk(DBGLVL_API, " (becomes dev->enc[%d])\n", |
| encport->nr); |
| } |
| break; |
| case FEATURE_UNIT: |
| afd = (struct tmComResAFeatureDescrHeader *)(buf + idx); |
| dprintk(DBGLVL_API, " FEATURE_UNIT\n"); |
| dprintk(DBGLVL_API, " unitid = 0x%x\n", |
| afd->unitid); |
| dprintk(DBGLVL_API, " sourceid = 0x%x\n", |
| afd->sourceid); |
| dprintk(DBGLVL_API, " controlsize = 0x%x\n", |
| afd->controlsize); |
| if (currpath == 1) |
| encport = &dev->ports[SAA7164_PORT_ENC1]; |
| else |
| encport = &dev->ports[SAA7164_PORT_ENC2]; |
| memcpy(&encport->audfeat, afd, |
| sizeof(struct tmComResAFeatureDescrHeader)); |
| dprintk(DBGLVL_API, " (becomes dev->enc[%d])\n", |
| encport->nr); |
| break; |
| case ENCODER_UNIT: |
| edh = (struct tmComResEncoderDescrHeader *)(buf + idx); |
| dprintk(DBGLVL_API, " ENCODER_UNIT\n"); |
| dprintk(DBGLVL_API, " subtype = 0x%x\n", edh->subtype); |
| dprintk(DBGLVL_API, " unitid = 0x%x\n", edh->unitid); |
| dprintk(DBGLVL_API, " vsourceid = 0x%x\n", |
| edh->vsourceid); |
| dprintk(DBGLVL_API, " asourceid = 0x%x\n", |
| edh->asourceid); |
| dprintk(DBGLVL_API, " iunit = 0x%x\n", edh->iunit); |
| if (edh->iunit == edh->unitid) { |
| if (currpath == 1) |
| encport = &dev->ports[SAA7164_PORT_ENC1]; |
| else |
| encport = &dev->ports[SAA7164_PORT_ENC2]; |
| memcpy(&encport->encunit, edh, |
| sizeof(struct tmComResEncoderDescrHeader)); |
| dprintk(DBGLVL_API, |
| " (becomes dev->enc[%d])\n", |
| encport->nr); |
| } |
| break; |
| case EXTENSION_UNIT: |
| dprintk(DBGLVL_API, " EXTENSION_UNIT\n"); |
| exthdr = (struct tmComResExtDevDescrHeader *)(buf + idx); |
| dprintk(DBGLVL_API, " unitid = 0x%x\n", |
| exthdr->unitid); |
| dprintk(DBGLVL_API, " deviceid = 0x%x\n", |
| exthdr->deviceid); |
| dprintk(DBGLVL_API, " devicetype = 0x%x\n", |
| exthdr->devicetype); |
| if (exthdr->devicetype & 0x1) |
| dprintk(DBGLVL_API, " = Decoder Device\n"); |
| if (exthdr->devicetype & 0x2) |
| dprintk(DBGLVL_API, " = GPIO Source\n"); |
| if (exthdr->devicetype & 0x4) |
| dprintk(DBGLVL_API, " = Video Decoder\n"); |
| if (exthdr->devicetype & 0x8) |
| dprintk(DBGLVL_API, " = Audio Decoder\n"); |
| if (exthdr->devicetype & 0x20) |
| dprintk(DBGLVL_API, " = Crossbar\n"); |
| if (exthdr->devicetype & 0x40) |
| dprintk(DBGLVL_API, " = Tuner\n"); |
| if (exthdr->devicetype & 0x80) |
| dprintk(DBGLVL_API, " = IF PLL\n"); |
| if (exthdr->devicetype & 0x100) |
| dprintk(DBGLVL_API, " = Demodulator\n"); |
| if (exthdr->devicetype & 0x200) |
| dprintk(DBGLVL_API, " = RDS Decoder\n"); |
| if (exthdr->devicetype & 0x400) |
| dprintk(DBGLVL_API, " = Encoder\n"); |
| if (exthdr->devicetype & 0x800) |
| dprintk(DBGLVL_API, " = IR Decoder\n"); |
| if (exthdr->devicetype & 0x1000) |
| dprintk(DBGLVL_API, " = EEPROM\n"); |
| if (exthdr->devicetype & 0x2000) |
| dprintk(DBGLVL_API, |
| " = VBI Decoder\n"); |
| if (exthdr->devicetype & 0x10000) |
| dprintk(DBGLVL_API, |
| " = Streaming Device\n"); |
| if (exthdr->devicetype & 0x20000) |
| dprintk(DBGLVL_API, |
| " = DRM Device\n"); |
| if (exthdr->devicetype & 0x40000000) |
| dprintk(DBGLVL_API, |
| " = Generic Device\n"); |
| if (exthdr->devicetype & 0x80000000) |
| dprintk(DBGLVL_API, |
| " = Config Space Device\n"); |
| dprintk(DBGLVL_API, " numgpiopins = 0x%x\n", |
| exthdr->numgpiopins); |
| dprintk(DBGLVL_API, " numgpiogroups = 0x%x\n", |
| exthdr->numgpiogroups); |
| dprintk(DBGLVL_API, " controlsize = 0x%x\n", |
| exthdr->controlsize); |
| if (exthdr->devicetype & 0x80) { |
| if (currpath == 1) |
| encport = &dev->ports[SAA7164_PORT_ENC1]; |
| else |
| encport = &dev->ports[SAA7164_PORT_ENC2]; |
| memcpy(&encport->ifunit, exthdr, |
| sizeof(struct tmComResExtDevDescrHeader)); |
| dprintk(DBGLVL_API, |
| " (becomes dev->enc[%d])\n", |
| encport->nr); |
| } |
| break; |
| case PVC_INFRARED_UNIT: |
| dprintk(DBGLVL_API, " PVC_INFRARED_UNIT\n"); |
| break; |
| case DRM_UNIT: |
| dprintk(DBGLVL_API, " DRM_UNIT\n"); |
| break; |
| default: |
| dprintk(DBGLVL_API, "default %d\n", hdr->subtype); |
| } |
| |
| dprintk(DBGLVL_API, " 1.%x\n", hdr->len); |
| dprintk(DBGLVL_API, " 2.%x\n", hdr->type); |
| dprintk(DBGLVL_API, " 3.%x\n", hdr->subtype); |
| dprintk(DBGLVL_API, " 4.%x\n", hdr->unitid); |
| |
| idx += hdr->len; |
| } |
| |
| return 0; |
| } |
| |
| int saa7164_api_enum_subdevs(struct saa7164_dev *dev) |
| { |
| int ret; |
| u32 buflen = 0; |
| u8 *buf; |
| |
| dprintk(DBGLVL_API, "%s()\n", __func__); |
| |
| /* Get the total descriptor length */ |
| ret = saa7164_cmd_send(dev, 0, GET_LEN, |
| GET_DESCRIPTORS_CONTROL, sizeof(buflen), &buflen); |
| if (ret != SAA_OK) |
| printk(KERN_ERR "%s() error, ret = 0x%x\n", __func__, ret); |
| |
| dprintk(DBGLVL_API, "%s() total descriptor size = %d bytes.\n", |
| __func__, buflen); |
| |
| /* Allocate enough storage for all of the descs */ |
| buf = kzalloc(buflen, GFP_KERNEL); |
| if (!buf) |
| return SAA_ERR_NO_RESOURCES; |
| |
| /* Retrieve them */ |
| ret = saa7164_cmd_send(dev, 0, GET_CUR, |
| GET_DESCRIPTORS_CONTROL, buflen, buf); |
| if (ret != SAA_OK) { |
| printk(KERN_ERR "%s() error, ret = 0x%x\n", __func__, ret); |
| goto out; |
| } |
| |
| if (saa_debug & DBGLVL_API) |
| print_hex_dump(KERN_INFO, "", DUMP_PREFIX_OFFSET, 16, 1, buf, |
| buflen & ~15, false); |
| |
| saa7164_api_dump_subdevs(dev, buf, buflen); |
| |
| out: |
| kfree(buf); |
| return ret; |
| } |
| |
| int saa7164_api_i2c_read(struct saa7164_i2c *bus, u8 addr, u32 reglen, u8 *reg, |
| u32 datalen, u8 *data) |
| { |
| struct saa7164_dev *dev = bus->dev; |
| u16 len = 0; |
| int unitid; |
| u8 buf[256]; |
| int ret; |
| |
| dprintk(DBGLVL_API, "%s() addr=%x reglen=%d datalen=%d\n", |
| __func__, addr, reglen, datalen); |
| |
| if (reglen > 4) |
| return -EIO; |
| |
| /* Prepare the send buffer */ |
| /* Bytes 00-03 source register length |
| * 04-07 source bytes to read |
| * 08... register address |
| */ |
| memset(buf, 0, sizeof(buf)); |
| memcpy((buf + 2 * sizeof(u32) + 0), reg, reglen); |
| *((u32 *)(buf + 0 * sizeof(u32))) = reglen; |
| *((u32 *)(buf + 1 * sizeof(u32))) = datalen; |
| |
| unitid = saa7164_i2caddr_to_unitid(bus, addr); |
| if (unitid < 0) { |
| printk(KERN_ERR |
| "%s() error, cannot translate regaddr 0x%x to unitid\n", |
| __func__, addr); |
| return -EIO; |
| } |
| |
| ret = saa7164_cmd_send(bus->dev, unitid, GET_LEN, |
| EXU_REGISTER_ACCESS_CONTROL, sizeof(len), &len); |
| if (ret != SAA_OK) { |
| printk(KERN_ERR "%s() error, ret(1) = 0x%x\n", __func__, ret); |
| return -EIO; |
| } |
| |
| dprintk(DBGLVL_API, "%s() len = %d bytes\n", __func__, len); |
| |
| if (saa_debug & DBGLVL_I2C) |
| print_hex_dump(KERN_INFO, "", DUMP_PREFIX_OFFSET, 16, 1, buf, |
| 32, false); |
| |
| ret = saa7164_cmd_send(bus->dev, unitid, GET_CUR, |
| EXU_REGISTER_ACCESS_CONTROL, len, &buf); |
| if (ret != SAA_OK) |
| printk(KERN_ERR "%s() error, ret(2) = 0x%x\n", __func__, ret); |
| else { |
| if (saa_debug & DBGLVL_I2C) |
| print_hex_dump(KERN_INFO, "", DUMP_PREFIX_OFFSET, 16, 1, |
| buf, sizeof(buf), false); |
| memcpy(data, (buf + 2 * sizeof(u32) + reglen), datalen); |
| } |
| |
| return ret == SAA_OK ? 0 : -EIO; |
| } |
| |
| /* For a given 8 bit i2c address device, write the buffer */ |
| int saa7164_api_i2c_write(struct saa7164_i2c *bus, u8 addr, u32 datalen, |
| u8 *data) |
| { |
| struct saa7164_dev *dev = bus->dev; |
| u16 len = 0; |
| int unitid; |
| int reglen; |
| u8 buf[256]; |
| int ret; |
| |
| dprintk(DBGLVL_API, "%s() addr=0x%2x len=0x%x\n", |
| __func__, addr, datalen); |
| |
| if ((datalen == 0) || (datalen > 232)) |
| return -EIO; |
| |
| memset(buf, 0, sizeof(buf)); |
| |
| unitid = saa7164_i2caddr_to_unitid(bus, addr); |
| if (unitid < 0) { |
| printk(KERN_ERR |
| "%s() error, cannot translate regaddr 0x%x to unitid\n", |
| __func__, addr); |
| return -EIO; |
| } |
| |
| reglen = saa7164_i2caddr_to_reglen(bus, addr); |
| if (reglen < 0) { |
| printk(KERN_ERR |
| "%s() error, cannot translate regaddr to reglen\n", |
| __func__); |
| return -EIO; |
| } |
| |
| ret = saa7164_cmd_send(bus->dev, unitid, GET_LEN, |
| EXU_REGISTER_ACCESS_CONTROL, sizeof(len), &len); |
| if (ret != SAA_OK) { |
| printk(KERN_ERR "%s() error, ret(1) = 0x%x\n", __func__, ret); |
| return -EIO; |
| } |
| |
| dprintk(DBGLVL_API, "%s() len = %d bytes unitid=0x%x\n", __func__, |
| len, unitid); |
| |
| /* Prepare the send buffer */ |
| /* Bytes 00-03 dest register length |
| * 04-07 dest bytes to write |
| * 08... register address |
| */ |
| *((u32 *)(buf + 0 * sizeof(u32))) = reglen; |
| *((u32 *)(buf + 1 * sizeof(u32))) = datalen - reglen; |
| memcpy((buf + 2 * sizeof(u32)), data, datalen); |
| |
| if (saa_debug & DBGLVL_I2C) |
| print_hex_dump(KERN_INFO, "", DUMP_PREFIX_OFFSET, 16, 1, |
| buf, sizeof(buf), false); |
| |
| ret = saa7164_cmd_send(bus->dev, unitid, SET_CUR, |
| EXU_REGISTER_ACCESS_CONTROL, len, &buf); |
| if (ret != SAA_OK) |
| printk(KERN_ERR "%s() error, ret(2) = 0x%x\n", __func__, ret); |
| |
| return ret == SAA_OK ? 0 : -EIO; |
| } |
| |
| static int saa7164_api_modify_gpio(struct saa7164_dev *dev, u8 unitid, |
| u8 pin, u8 state) |
| { |
| int ret; |
| struct tmComResGPIO t; |
| |
| dprintk(DBGLVL_API, "%s(0x%x, %d, %d)\n", |
| __func__, unitid, pin, state); |
| |
| if ((pin > 7) || (state > 2)) |
| return SAA_ERR_BAD_PARAMETER; |
| |
| t.pin = pin; |
| t.state = state; |
| |
| ret = saa7164_cmd_send(dev, unitid, SET_CUR, |
| EXU_GPIO_CONTROL, sizeof(t), &t); |
| if (ret != SAA_OK) |
| printk(KERN_ERR "%s() error, ret = 0x%x\n", |
| __func__, ret); |
| |
| return ret; |
| } |
| |
| int saa7164_api_set_gpiobit(struct saa7164_dev *dev, u8 unitid, |
| u8 pin) |
| { |
| return saa7164_api_modify_gpio(dev, unitid, pin, 1); |
| } |
| |
| int saa7164_api_clear_gpiobit(struct saa7164_dev *dev, u8 unitid, |
| u8 pin) |
| { |
| return saa7164_api_modify_gpio(dev, unitid, pin, 0); |
| } |
| |