| // SPDX-License-Identifier: GPL-2.0-or-later |
| |
| /* Advanced Micro Devices Inc. AMD8111E Linux Network Driver |
| * Copyright (C) 2004 Advanced Micro Devices |
| * |
| * Copyright 2001,2002 Jeff Garzik <jgarzik@mandrakesoft.com> [ 8139cp.c,tg3.c ] |
| * Copyright (C) 2001, 2002 David S. Miller (davem@redhat.com)[ tg3.c] |
| * Copyright 1996-1999 Thomas Bogendoerfer [ pcnet32.c ] |
| * Derived from the lance driver written 1993,1994,1995 by Donald Becker. |
| * Copyright 1993 United States Government as represented by the |
| * Director, National Security Agency.[ pcnet32.c ] |
| * Carsten Langgaard, carstenl@mips.com [ pcnet32.c ] |
| * Copyright (C) 2000 MIPS Technologies, Inc. All rights reserved. |
| * |
| |
| Module Name: |
| |
| amd8111e.c |
| |
| Abstract: |
| |
| AMD8111 based 10/100 Ethernet Controller Driver. |
| |
| Environment: |
| |
| Kernel Mode |
| |
| Revision History: |
| 3.0.0 |
| Initial Revision. |
| 3.0.1 |
| 1. Dynamic interrupt coalescing. |
| 2. Removed prev_stats. |
| 3. MII support. |
| 4. Dynamic IPG support |
| 3.0.2 05/29/2003 |
| 1. Bug fix: Fixed failure to send jumbo packets larger than 4k. |
| 2. Bug fix: Fixed VLAN support failure. |
| 3. Bug fix: Fixed receive interrupt coalescing bug. |
| 4. Dynamic IPG support is disabled by default. |
| 3.0.3 06/05/2003 |
| 1. Bug fix: Fixed failure to close the interface if SMP is enabled. |
| 3.0.4 12/09/2003 |
| 1. Added set_mac_address routine for bonding driver support. |
| 2. Tested the driver for bonding support |
| 3. Bug fix: Fixed mismach in actual receive buffer lenth and lenth |
| indicated to the h/w. |
| 4. Modified amd8111e_rx() routine to receive all the received packets |
| in the first interrupt. |
| 5. Bug fix: Corrected rx_errors reported in get_stats() function. |
| 3.0.5 03/22/2004 |
| 1. Added NAPI support |
| |
| */ |
| |
| |
| #include <linux/module.h> |
| #include <linux/kernel.h> |
| #include <linux/types.h> |
| #include <linux/compiler.h> |
| #include <linux/delay.h> |
| #include <linux/interrupt.h> |
| #include <linux/ioport.h> |
| #include <linux/pci.h> |
| #include <linux/netdevice.h> |
| #include <linux/etherdevice.h> |
| #include <linux/skbuff.h> |
| #include <linux/ethtool.h> |
| #include <linux/mii.h> |
| #include <linux/if_vlan.h> |
| #include <linux/ctype.h> |
| #include <linux/crc32.h> |
| #include <linux/dma-mapping.h> |
| |
| #include <asm/io.h> |
| #include <asm/byteorder.h> |
| #include <linux/uaccess.h> |
| |
| #if IS_ENABLED(CONFIG_VLAN_8021Q) |
| #define AMD8111E_VLAN_TAG_USED 1 |
| #else |
| #define AMD8111E_VLAN_TAG_USED 0 |
| #endif |
| |
| #include "amd8111e.h" |
| #define MODULE_NAME "amd8111e" |
| MODULE_AUTHOR("Advanced Micro Devices, Inc."); |
| MODULE_DESCRIPTION("AMD8111 based 10/100 Ethernet Controller."); |
| MODULE_LICENSE("GPL"); |
| module_param_array(speed_duplex, int, NULL, 0); |
| MODULE_PARM_DESC(speed_duplex, "Set device speed and duplex modes, 0: Auto Negotiate, 1: 10Mbps Half Duplex, 2: 10Mbps Full Duplex, 3: 100Mbps Half Duplex, 4: 100Mbps Full Duplex"); |
| module_param_array(coalesce, bool, NULL, 0); |
| MODULE_PARM_DESC(coalesce, "Enable or Disable interrupt coalescing, 1: Enable, 0: Disable"); |
| module_param_array(dynamic_ipg, bool, NULL, 0); |
| MODULE_PARM_DESC(dynamic_ipg, "Enable or Disable dynamic IPG, 1: Enable, 0: Disable"); |
| |
| /* This function will read the PHY registers. */ |
| static int amd8111e_read_phy(struct amd8111e_priv *lp, |
| int phy_id, int reg, u32 *val) |
| { |
| void __iomem *mmio = lp->mmio; |
| unsigned int reg_val; |
| unsigned int repeat = REPEAT_CNT; |
| |
| reg_val = readl(mmio + PHY_ACCESS); |
| while (reg_val & PHY_CMD_ACTIVE) |
| reg_val = readl(mmio + PHY_ACCESS); |
| |
| writel(PHY_RD_CMD | ((phy_id & 0x1f) << 21) | |
| ((reg & 0x1f) << 16), mmio + PHY_ACCESS); |
| do { |
| reg_val = readl(mmio + PHY_ACCESS); |
| udelay(30); /* It takes 30 us to read/write data */ |
| } while (--repeat && (reg_val & PHY_CMD_ACTIVE)); |
| if (reg_val & PHY_RD_ERR) |
| goto err_phy_read; |
| |
| *val = reg_val & 0xffff; |
| return 0; |
| err_phy_read: |
| *val = 0; |
| return -EINVAL; |
| |
| } |
| |
| /* This function will write into PHY registers. */ |
| static int amd8111e_write_phy(struct amd8111e_priv *lp, |
| int phy_id, int reg, u32 val) |
| { |
| unsigned int repeat = REPEAT_CNT; |
| void __iomem *mmio = lp->mmio; |
| unsigned int reg_val; |
| |
| reg_val = readl(mmio + PHY_ACCESS); |
| while (reg_val & PHY_CMD_ACTIVE) |
| reg_val = readl(mmio + PHY_ACCESS); |
| |
| writel(PHY_WR_CMD | ((phy_id & 0x1f) << 21) | |
| ((reg & 0x1f) << 16)|val, mmio + PHY_ACCESS); |
| |
| do { |
| reg_val = readl(mmio + PHY_ACCESS); |
| udelay(30); /* It takes 30 us to read/write the data */ |
| } while (--repeat && (reg_val & PHY_CMD_ACTIVE)); |
| |
| if (reg_val & PHY_RD_ERR) |
| goto err_phy_write; |
| |
| return 0; |
| |
| err_phy_write: |
| return -EINVAL; |
| |
| } |
| |
| /* This is the mii register read function provided to the mii interface. */ |
| static int amd8111e_mdio_read(struct net_device *dev, int phy_id, int reg_num) |
| { |
| struct amd8111e_priv *lp = netdev_priv(dev); |
| unsigned int reg_val; |
| |
| amd8111e_read_phy(lp, phy_id, reg_num, ®_val); |
| return reg_val; |
| |
| } |
| |
| /* This is the mii register write function provided to the mii interface. */ |
| static void amd8111e_mdio_write(struct net_device *dev, |
| int phy_id, int reg_num, int val) |
| { |
| struct amd8111e_priv *lp = netdev_priv(dev); |
| |
| amd8111e_write_phy(lp, phy_id, reg_num, val); |
| } |
| |
| /* This function will set PHY speed. During initialization sets |
| * the original speed to 100 full |
| */ |
| static void amd8111e_set_ext_phy(struct net_device *dev) |
| { |
| struct amd8111e_priv *lp = netdev_priv(dev); |
| u32 bmcr, advert, tmp; |
| |
| /* Determine mii register values to set the speed */ |
| advert = amd8111e_mdio_read(dev, lp->ext_phy_addr, MII_ADVERTISE); |
| tmp = advert & ~(ADVERTISE_ALL | ADVERTISE_100BASE4); |
| switch (lp->ext_phy_option) { |
| |
| default: |
| case SPEED_AUTONEG: /* advertise all values */ |
| tmp |= (ADVERTISE_10HALF | ADVERTISE_10FULL | |
| ADVERTISE_100HALF | ADVERTISE_100FULL); |
| break; |
| case SPEED10_HALF: |
| tmp |= ADVERTISE_10HALF; |
| break; |
| case SPEED10_FULL: |
| tmp |= ADVERTISE_10FULL; |
| break; |
| case SPEED100_HALF: |
| tmp |= ADVERTISE_100HALF; |
| break; |
| case SPEED100_FULL: |
| tmp |= ADVERTISE_100FULL; |
| break; |
| } |
| |
| if(advert != tmp) |
| amd8111e_mdio_write(dev, lp->ext_phy_addr, MII_ADVERTISE, tmp); |
| /* Restart auto negotiation */ |
| bmcr = amd8111e_mdio_read(dev, lp->ext_phy_addr, MII_BMCR); |
| bmcr |= (BMCR_ANENABLE | BMCR_ANRESTART); |
| amd8111e_mdio_write(dev, lp->ext_phy_addr, MII_BMCR, bmcr); |
| |
| } |
| |
| /* This function will unmap skb->data space and will free |
| * all transmit and receive skbuffs. |
| */ |
| static int amd8111e_free_skbs(struct net_device *dev) |
| { |
| struct amd8111e_priv *lp = netdev_priv(dev); |
| struct sk_buff *rx_skbuff; |
| int i; |
| |
| /* Freeing transmit skbs */ |
| for (i = 0; i < NUM_TX_BUFFERS; i++) { |
| if (lp->tx_skbuff[i]) { |
| dma_unmap_single(&lp->pci_dev->dev, |
| lp->tx_dma_addr[i], |
| lp->tx_skbuff[i]->len, DMA_TO_DEVICE); |
| dev_kfree_skb(lp->tx_skbuff[i]); |
| lp->tx_skbuff[i] = NULL; |
| lp->tx_dma_addr[i] = 0; |
| } |
| } |
| /* Freeing previously allocated receive buffers */ |
| for (i = 0; i < NUM_RX_BUFFERS; i++) { |
| rx_skbuff = lp->rx_skbuff[i]; |
| if (rx_skbuff != NULL) { |
| dma_unmap_single(&lp->pci_dev->dev, |
| lp->rx_dma_addr[i], |
| lp->rx_buff_len - 2, DMA_FROM_DEVICE); |
| dev_kfree_skb(lp->rx_skbuff[i]); |
| lp->rx_skbuff[i] = NULL; |
| lp->rx_dma_addr[i] = 0; |
| } |
| } |
| |
| return 0; |
| } |
| |
| /* This will set the receive buffer length corresponding |
| * to the mtu size of networkinterface. |
| */ |
| static inline void amd8111e_set_rx_buff_len(struct net_device *dev) |
| { |
| struct amd8111e_priv *lp = netdev_priv(dev); |
| unsigned int mtu = dev->mtu; |
| |
| if (mtu > ETH_DATA_LEN) { |
| /* MTU + ethernet header + FCS |
| * + optional VLAN tag + skb reserve space 2 |
| */ |
| lp->rx_buff_len = mtu + ETH_HLEN + 10; |
| lp->options |= OPTION_JUMBO_ENABLE; |
| } else { |
| lp->rx_buff_len = PKT_BUFF_SZ; |
| lp->options &= ~OPTION_JUMBO_ENABLE; |
| } |
| } |
| |
| /* This function will free all the previously allocated buffers, |
| * determine new receive buffer length and will allocate new receive buffers. |
| * This function also allocates and initializes both the transmitter |
| * and receive hardware descriptors. |
| */ |
| static int amd8111e_init_ring(struct net_device *dev) |
| { |
| struct amd8111e_priv *lp = netdev_priv(dev); |
| int i; |
| |
| lp->rx_idx = lp->tx_idx = 0; |
| lp->tx_complete_idx = 0; |
| lp->tx_ring_idx = 0; |
| |
| |
| if (lp->opened) |
| /* Free previously allocated transmit and receive skbs */ |
| amd8111e_free_skbs(dev); |
| |
| else { |
| /* allocate the tx and rx descriptors */ |
| lp->tx_ring = dma_alloc_coherent(&lp->pci_dev->dev, |
| sizeof(struct amd8111e_tx_dr) * NUM_TX_RING_DR, |
| &lp->tx_ring_dma_addr, GFP_ATOMIC); |
| if (!lp->tx_ring) |
| goto err_no_mem; |
| |
| lp->rx_ring = dma_alloc_coherent(&lp->pci_dev->dev, |
| sizeof(struct amd8111e_rx_dr) * NUM_RX_RING_DR, |
| &lp->rx_ring_dma_addr, GFP_ATOMIC); |
| if (!lp->rx_ring) |
| goto err_free_tx_ring; |
| } |
| |
| /* Set new receive buff size */ |
| amd8111e_set_rx_buff_len(dev); |
| |
| /* Allocating receive skbs */ |
| for (i = 0; i < NUM_RX_BUFFERS; i++) { |
| |
| lp->rx_skbuff[i] = netdev_alloc_skb(dev, lp->rx_buff_len); |
| if (!lp->rx_skbuff[i]) { |
| /* Release previos allocated skbs */ |
| for (--i; i >= 0; i--) |
| dev_kfree_skb(lp->rx_skbuff[i]); |
| goto err_free_rx_ring; |
| } |
| skb_reserve(lp->rx_skbuff[i], 2); |
| } |
| /* Initilaizing receive descriptors */ |
| for (i = 0; i < NUM_RX_BUFFERS; i++) { |
| lp->rx_dma_addr[i] = dma_map_single(&lp->pci_dev->dev, |
| lp->rx_skbuff[i]->data, |
| lp->rx_buff_len - 2, |
| DMA_FROM_DEVICE); |
| |
| lp->rx_ring[i].buff_phy_addr = cpu_to_le32(lp->rx_dma_addr[i]); |
| lp->rx_ring[i].buff_count = cpu_to_le16(lp->rx_buff_len-2); |
| wmb(); |
| lp->rx_ring[i].rx_flags = cpu_to_le16(OWN_BIT); |
| } |
| |
| /* Initializing transmit descriptors */ |
| for (i = 0; i < NUM_TX_RING_DR; i++) { |
| lp->tx_ring[i].buff_phy_addr = 0; |
| lp->tx_ring[i].tx_flags = 0; |
| lp->tx_ring[i].buff_count = 0; |
| } |
| |
| return 0; |
| |
| err_free_rx_ring: |
| |
| dma_free_coherent(&lp->pci_dev->dev, |
| sizeof(struct amd8111e_rx_dr) * NUM_RX_RING_DR, |
| lp->rx_ring, lp->rx_ring_dma_addr); |
| |
| err_free_tx_ring: |
| |
| dma_free_coherent(&lp->pci_dev->dev, |
| sizeof(struct amd8111e_tx_dr) * NUM_TX_RING_DR, |
| lp->tx_ring, lp->tx_ring_dma_addr); |
| |
| err_no_mem: |
| return -ENOMEM; |
| } |
| |
| /* This function will set the interrupt coalescing according |
| * to the input arguments |
| */ |
| static int amd8111e_set_coalesce(struct net_device *dev, enum coal_mode cmod) |
| { |
| unsigned int timeout; |
| unsigned int event_count; |
| |
| struct amd8111e_priv *lp = netdev_priv(dev); |
| void __iomem *mmio = lp->mmio; |
| struct amd8111e_coalesce_conf *coal_conf = &lp->coal_conf; |
| |
| |
| switch(cmod) |
| { |
| case RX_INTR_COAL : |
| timeout = coal_conf->rx_timeout; |
| event_count = coal_conf->rx_event_count; |
| if (timeout > MAX_TIMEOUT || |
| event_count > MAX_EVENT_COUNT) |
| return -EINVAL; |
| |
| timeout = timeout * DELAY_TIMER_CONV; |
| writel(VAL0|STINTEN, mmio+INTEN0); |
| writel((u32)DLY_INT_A_R0 | (event_count << 16) | |
| timeout, mmio + DLY_INT_A); |
| break; |
| |
| case TX_INTR_COAL: |
| timeout = coal_conf->tx_timeout; |
| event_count = coal_conf->tx_event_count; |
| if (timeout > MAX_TIMEOUT || |
| event_count > MAX_EVENT_COUNT) |
| return -EINVAL; |
| |
| |
| timeout = timeout * DELAY_TIMER_CONV; |
| writel(VAL0 | STINTEN, mmio + INTEN0); |
| writel((u32)DLY_INT_B_T0 | (event_count << 16) | |
| timeout, mmio + DLY_INT_B); |
| break; |
| |
| case DISABLE_COAL: |
| writel(0, mmio + STVAL); |
| writel(STINTEN, mmio + INTEN0); |
| writel(0, mmio + DLY_INT_B); |
| writel(0, mmio + DLY_INT_A); |
| break; |
| case ENABLE_COAL: |
| /* Start the timer */ |
| writel((u32)SOFT_TIMER_FREQ, mmio + STVAL); /* 0.5 sec */ |
| writel(VAL0 | STINTEN, mmio + INTEN0); |
| break; |
| default: |
| break; |
| |
| } |
| return 0; |
| |
| } |
| |
| /* This function initializes the device registers and starts the device. */ |
| static int amd8111e_restart(struct net_device *dev) |
| { |
| struct amd8111e_priv *lp = netdev_priv(dev); |
| void __iomem *mmio = lp->mmio; |
| int i, reg_val; |
| |
| /* stop the chip */ |
| writel(RUN, mmio + CMD0); |
| |
| if (amd8111e_init_ring(dev)) |
| return -ENOMEM; |
| |
| /* enable the port manager and set auto negotiation always */ |
| writel((u32)VAL1 | EN_PMGR, mmio + CMD3); |
| writel((u32)XPHYANE | XPHYRST, mmio + CTRL2); |
| |
| amd8111e_set_ext_phy(dev); |
| |
| /* set control registers */ |
| reg_val = readl(mmio + CTRL1); |
| reg_val &= ~XMTSP_MASK; |
| writel(reg_val | XMTSP_128 | CACHE_ALIGN, mmio + CTRL1); |
| |
| /* enable interrupt */ |
| writel(APINT5EN | APINT4EN | APINT3EN | APINT2EN | APINT1EN | |
| APINT0EN | MIIPDTINTEN | MCCIINTEN | MCCINTEN | MREINTEN | |
| SPNDINTEN | MPINTEN | SINTEN | STINTEN, mmio + INTEN0); |
| |
| writel(VAL3 | LCINTEN | VAL1 | TINTEN0 | VAL0 | RINTEN0, mmio + INTEN0); |
| |
| /* initialize tx and rx ring base addresses */ |
| writel((u32)lp->tx_ring_dma_addr, mmio + XMT_RING_BASE_ADDR0); |
| writel((u32)lp->rx_ring_dma_addr, mmio + RCV_RING_BASE_ADDR0); |
| |
| writew((u32)NUM_TX_RING_DR, mmio + XMT_RING_LEN0); |
| writew((u16)NUM_RX_RING_DR, mmio + RCV_RING_LEN0); |
| |
| /* set default IPG to 96 */ |
| writew((u32)DEFAULT_IPG, mmio + IPG); |
| writew((u32)(DEFAULT_IPG-IFS1_DELTA), mmio + IFS1); |
| |
| if (lp->options & OPTION_JUMBO_ENABLE) { |
| writel((u32)VAL2|JUMBO, mmio + CMD3); |
| /* Reset REX_UFLO */ |
| writel(REX_UFLO, mmio + CMD2); |
| /* Should not set REX_UFLO for jumbo frames */ |
| writel(VAL0 | APAD_XMT | REX_RTRY, mmio + CMD2); |
| } else { |
| writel(VAL0 | APAD_XMT | REX_RTRY | REX_UFLO, mmio + CMD2); |
| writel((u32)JUMBO, mmio + CMD3); |
| } |
| |
| #if AMD8111E_VLAN_TAG_USED |
| writel((u32)VAL2 | VSIZE | VL_TAG_DEL, mmio + CMD3); |
| #endif |
| writel(VAL0 | APAD_XMT | REX_RTRY, mmio + CMD2); |
| |
| /* Setting the MAC address to the device */ |
| for (i = 0; i < ETH_ALEN; i++) |
| writeb(dev->dev_addr[i], mmio + PADR + i); |
| |
| /* Enable interrupt coalesce */ |
| if (lp->options & OPTION_INTR_COAL_ENABLE) { |
| netdev_info(dev, "Interrupt Coalescing Enabled.\n"); |
| amd8111e_set_coalesce(dev, ENABLE_COAL); |
| } |
| |
| /* set RUN bit to start the chip */ |
| writel(VAL2 | RDMD0, mmio + CMD0); |
| writel(VAL0 | INTREN | RUN, mmio + CMD0); |
| |
| /* To avoid PCI posting bug */ |
| readl(mmio+CMD0); |
| return 0; |
| } |
| |
| /* This function clears necessary the device registers. */ |
| static void amd8111e_init_hw_default(struct amd8111e_priv *lp) |
| { |
| unsigned int reg_val; |
| unsigned int logic_filter[2] = {0,}; |
| void __iomem *mmio = lp->mmio; |
| |
| |
| /* stop the chip */ |
| writel(RUN, mmio + CMD0); |
| |
| /* AUTOPOLL0 Register *//*TBD default value is 8100 in FPS */ |
| writew( 0x8100 | lp->ext_phy_addr, mmio + AUTOPOLL0); |
| |
| /* Clear RCV_RING_BASE_ADDR */ |
| writel(0, mmio + RCV_RING_BASE_ADDR0); |
| |
| /* Clear XMT_RING_BASE_ADDR */ |
| writel(0, mmio + XMT_RING_BASE_ADDR0); |
| writel(0, mmio + XMT_RING_BASE_ADDR1); |
| writel(0, mmio + XMT_RING_BASE_ADDR2); |
| writel(0, mmio + XMT_RING_BASE_ADDR3); |
| |
| /* Clear CMD0 */ |
| writel(CMD0_CLEAR, mmio + CMD0); |
| |
| /* Clear CMD2 */ |
| writel(CMD2_CLEAR, mmio + CMD2); |
| |
| /* Clear CMD7 */ |
| writel(CMD7_CLEAR, mmio + CMD7); |
| |
| /* Clear DLY_INT_A and DLY_INT_B */ |
| writel(0x0, mmio + DLY_INT_A); |
| writel(0x0, mmio + DLY_INT_B); |
| |
| /* Clear FLOW_CONTROL */ |
| writel(0x0, mmio + FLOW_CONTROL); |
| |
| /* Clear INT0 write 1 to clear register */ |
| reg_val = readl(mmio + INT0); |
| writel(reg_val, mmio + INT0); |
| |
| /* Clear STVAL */ |
| writel(0x0, mmio + STVAL); |
| |
| /* Clear INTEN0 */ |
| writel(INTEN0_CLEAR, mmio + INTEN0); |
| |
| /* Clear LADRF */ |
| writel(0x0, mmio + LADRF); |
| |
| /* Set SRAM_SIZE & SRAM_BOUNDARY registers */ |
| writel(0x80010, mmio + SRAM_SIZE); |
| |
| /* Clear RCV_RING0_LEN */ |
| writel(0x0, mmio + RCV_RING_LEN0); |
| |
| /* Clear XMT_RING0/1/2/3_LEN */ |
| writel(0x0, mmio + XMT_RING_LEN0); |
| writel(0x0, mmio + XMT_RING_LEN1); |
| writel(0x0, mmio + XMT_RING_LEN2); |
| writel(0x0, mmio + XMT_RING_LEN3); |
| |
| /* Clear XMT_RING_LIMIT */ |
| writel(0x0, mmio + XMT_RING_LIMIT); |
| |
| /* Clear MIB */ |
| writew(MIB_CLEAR, mmio + MIB_ADDR); |
| |
| /* Clear LARF */ |
| amd8111e_writeq(*(u64 *)logic_filter, mmio + LADRF); |
| |
| /* SRAM_SIZE register */ |
| reg_val = readl(mmio + SRAM_SIZE); |
| |
| if (lp->options & OPTION_JUMBO_ENABLE) |
| writel(VAL2 | JUMBO, mmio + CMD3); |
| #if AMD8111E_VLAN_TAG_USED |
| writel(VAL2 | VSIZE | VL_TAG_DEL, mmio + CMD3); |
| #endif |
| /* Set default value to CTRL1 Register */ |
| writel(CTRL1_DEFAULT, mmio + CTRL1); |
| |
| /* To avoid PCI posting bug */ |
| readl(mmio + CMD2); |
| |
| } |
| |
| /* This function disables the interrupt and clears all the pending |
| * interrupts in INT0 |
| */ |
| static void amd8111e_disable_interrupt(struct amd8111e_priv *lp) |
| { |
| u32 intr0; |
| |
| /* Disable interrupt */ |
| writel(INTREN, lp->mmio + CMD0); |
| |
| /* Clear INT0 */ |
| intr0 = readl(lp->mmio + INT0); |
| writel(intr0, lp->mmio + INT0); |
| |
| /* To avoid PCI posting bug */ |
| readl(lp->mmio + INT0); |
| |
| } |
| |
| /* This function stops the chip. */ |
| static void amd8111e_stop_chip(struct amd8111e_priv *lp) |
| { |
| writel(RUN, lp->mmio + CMD0); |
| |
| /* To avoid PCI posting bug */ |
| readl(lp->mmio + CMD0); |
| } |
| |
| /* This function frees the transmiter and receiver descriptor rings. */ |
| static void amd8111e_free_ring(struct amd8111e_priv *lp) |
| { |
| /* Free transmit and receive descriptor rings */ |
| if (lp->rx_ring) { |
| dma_free_coherent(&lp->pci_dev->dev, |
| sizeof(struct amd8111e_rx_dr) * NUM_RX_RING_DR, |
| lp->rx_ring, lp->rx_ring_dma_addr); |
| lp->rx_ring = NULL; |
| } |
| |
| if (lp->tx_ring) { |
| dma_free_coherent(&lp->pci_dev->dev, |
| sizeof(struct amd8111e_tx_dr) * NUM_TX_RING_DR, |
| lp->tx_ring, lp->tx_ring_dma_addr); |
| |
| lp->tx_ring = NULL; |
| } |
| |
| } |
| |
| /* This function will free all the transmit skbs that are actually |
| * transmitted by the device. It will check the ownership of the |
| * skb before freeing the skb. |
| */ |
| static int amd8111e_tx(struct net_device *dev) |
| { |
| struct amd8111e_priv *lp = netdev_priv(dev); |
| int tx_index; |
| int status; |
| /* Complete all the transmit packet */ |
| while (lp->tx_complete_idx != lp->tx_idx) { |
| tx_index = lp->tx_complete_idx & TX_RING_DR_MOD_MASK; |
| status = le16_to_cpu(lp->tx_ring[tx_index].tx_flags); |
| |
| if (status & OWN_BIT) |
| break; /* It still hasn't been Txed */ |
| |
| lp->tx_ring[tx_index].buff_phy_addr = 0; |
| |
| /* We must free the original skb */ |
| if (lp->tx_skbuff[tx_index]) { |
| dma_unmap_single(&lp->pci_dev->dev, |
| lp->tx_dma_addr[tx_index], |
| lp->tx_skbuff[tx_index]->len, |
| DMA_TO_DEVICE); |
| dev_consume_skb_irq(lp->tx_skbuff[tx_index]); |
| lp->tx_skbuff[tx_index] = NULL; |
| lp->tx_dma_addr[tx_index] = 0; |
| } |
| lp->tx_complete_idx++; |
| /*COAL update tx coalescing parameters */ |
| lp->coal_conf.tx_packets++; |
| lp->coal_conf.tx_bytes += |
| le16_to_cpu(lp->tx_ring[tx_index].buff_count); |
| |
| if (netif_queue_stopped(dev) && |
| lp->tx_complete_idx > lp->tx_idx - NUM_TX_BUFFERS + 2) { |
| /* The ring is no longer full, clear tbusy. */ |
| /* lp->tx_full = 0; */ |
| netif_wake_queue(dev); |
| } |
| } |
| return 0; |
| } |
| |
| /* This function handles the driver receive operation in polling mode */ |
| static int amd8111e_rx_poll(struct napi_struct *napi, int budget) |
| { |
| struct amd8111e_priv *lp = container_of(napi, struct amd8111e_priv, napi); |
| struct net_device *dev = lp->amd8111e_net_dev; |
| int rx_index = lp->rx_idx & RX_RING_DR_MOD_MASK; |
| void __iomem *mmio = lp->mmio; |
| struct sk_buff *skb, *new_skb; |
| int min_pkt_len, status; |
| int num_rx_pkt = 0; |
| short pkt_len; |
| #if AMD8111E_VLAN_TAG_USED |
| short vtag; |
| #endif |
| |
| while (num_rx_pkt < budget) { |
| status = le16_to_cpu(lp->rx_ring[rx_index].rx_flags); |
| if (status & OWN_BIT) |
| break; |
| |
| /* There is a tricky error noted by John Murphy, |
| * <murf@perftech.com> to Russ Nelson: Even with |
| * full-sized * buffers it's possible for a |
| * jabber packet to use two buffers, with only |
| * the last correctly noting the error. |
| */ |
| if (status & ERR_BIT) { |
| /* resetting flags */ |
| lp->rx_ring[rx_index].rx_flags &= RESET_RX_FLAGS; |
| goto err_next_pkt; |
| } |
| /* check for STP and ENP */ |
| if (!((status & STP_BIT) && (status & ENP_BIT))) { |
| /* resetting flags */ |
| lp->rx_ring[rx_index].rx_flags &= RESET_RX_FLAGS; |
| goto err_next_pkt; |
| } |
| pkt_len = le16_to_cpu(lp->rx_ring[rx_index].msg_count) - 4; |
| |
| #if AMD8111E_VLAN_TAG_USED |
| vtag = status & TT_MASK; |
| /* MAC will strip vlan tag */ |
| if (vtag != 0) |
| min_pkt_len = MIN_PKT_LEN - 4; |
| else |
| #endif |
| min_pkt_len = MIN_PKT_LEN; |
| |
| if (pkt_len < min_pkt_len) { |
| lp->rx_ring[rx_index].rx_flags &= RESET_RX_FLAGS; |
| lp->drv_rx_errors++; |
| goto err_next_pkt; |
| } |
| new_skb = netdev_alloc_skb(dev, lp->rx_buff_len); |
| if (!new_skb) { |
| /* if allocation fail, |
| * ignore that pkt and go to next one |
| */ |
| lp->rx_ring[rx_index].rx_flags &= RESET_RX_FLAGS; |
| lp->drv_rx_errors++; |
| goto err_next_pkt; |
| } |
| |
| skb_reserve(new_skb, 2); |
| skb = lp->rx_skbuff[rx_index]; |
| dma_unmap_single(&lp->pci_dev->dev, lp->rx_dma_addr[rx_index], |
| lp->rx_buff_len - 2, DMA_FROM_DEVICE); |
| skb_put(skb, pkt_len); |
| lp->rx_skbuff[rx_index] = new_skb; |
| lp->rx_dma_addr[rx_index] = dma_map_single(&lp->pci_dev->dev, |
| new_skb->data, |
| lp->rx_buff_len - 2, |
| DMA_FROM_DEVICE); |
| |
| skb->protocol = eth_type_trans(skb, dev); |
| |
| #if AMD8111E_VLAN_TAG_USED |
| if (vtag == TT_VLAN_TAGGED) { |
| u16 vlan_tag = le16_to_cpu(lp->rx_ring[rx_index].tag_ctrl_info); |
| __vlan_hwaccel_put_tag(skb, htons(ETH_P_8021Q), vlan_tag); |
| } |
| #endif |
| napi_gro_receive(napi, skb); |
| /* COAL update rx coalescing parameters */ |
| lp->coal_conf.rx_packets++; |
| lp->coal_conf.rx_bytes += pkt_len; |
| num_rx_pkt++; |
| |
| err_next_pkt: |
| lp->rx_ring[rx_index].buff_phy_addr |
| = cpu_to_le32(lp->rx_dma_addr[rx_index]); |
| lp->rx_ring[rx_index].buff_count = |
| cpu_to_le16(lp->rx_buff_len-2); |
| wmb(); |
| lp->rx_ring[rx_index].rx_flags |= cpu_to_le16(OWN_BIT); |
| rx_index = (++lp->rx_idx) & RX_RING_DR_MOD_MASK; |
| } |
| |
| if (num_rx_pkt < budget && napi_complete_done(napi, num_rx_pkt)) { |
| unsigned long flags; |
| |
| /* Receive descriptor is empty now */ |
| spin_lock_irqsave(&lp->lock, flags); |
| writel(VAL0|RINTEN0, mmio + INTEN0); |
| writel(VAL2 | RDMD0, mmio + CMD0); |
| spin_unlock_irqrestore(&lp->lock, flags); |
| } |
| |
| return num_rx_pkt; |
| } |
| |
| /* This function will indicate the link status to the kernel. */ |
| static int amd8111e_link_change(struct net_device *dev) |
| { |
| struct amd8111e_priv *lp = netdev_priv(dev); |
| int status0, speed; |
| |
| /* read the link change */ |
| status0 = readl(lp->mmio + STAT0); |
| |
| if (status0 & LINK_STATS) { |
| if (status0 & AUTONEG_COMPLETE) |
| lp->link_config.autoneg = AUTONEG_ENABLE; |
| else |
| lp->link_config.autoneg = AUTONEG_DISABLE; |
| |
| if (status0 & FULL_DPLX) |
| lp->link_config.duplex = DUPLEX_FULL; |
| else |
| lp->link_config.duplex = DUPLEX_HALF; |
| speed = (status0 & SPEED_MASK) >> 7; |
| if (speed == PHY_SPEED_10) |
| lp->link_config.speed = SPEED_10; |
| else if (speed == PHY_SPEED_100) |
| lp->link_config.speed = SPEED_100; |
| |
| netdev_info(dev, "Link is Up. Speed is %s Mbps %s Duplex\n", |
| (lp->link_config.speed == SPEED_100) ? |
| "100" : "10", |
| (lp->link_config.duplex == DUPLEX_FULL) ? |
| "Full" : "Half"); |
| |
| netif_carrier_on(dev); |
| } else { |
| lp->link_config.speed = SPEED_INVALID; |
| lp->link_config.duplex = DUPLEX_INVALID; |
| lp->link_config.autoneg = AUTONEG_INVALID; |
| netdev_info(dev, "Link is Down.\n"); |
| netif_carrier_off(dev); |
| } |
| |
| return 0; |
| } |
| |
| /* This function reads the mib counters. */ |
| static int amd8111e_read_mib(void __iomem *mmio, u8 MIB_COUNTER) |
| { |
| unsigned int status; |
| unsigned int data; |
| unsigned int repeat = REPEAT_CNT; |
| |
| writew(MIB_RD_CMD | MIB_COUNTER, mmio + MIB_ADDR); |
| do { |
| status = readw(mmio + MIB_ADDR); |
| udelay(2); /* controller takes MAX 2 us to get mib data */ |
| } |
| while (--repeat && (status & MIB_CMD_ACTIVE)); |
| |
| data = readl(mmio + MIB_DATA); |
| return data; |
| } |
| |
| /* This function reads the mib registers and returns the hardware statistics. |
| * It updates previous internal driver statistics with new values. |
| */ |
| static struct net_device_stats *amd8111e_get_stats(struct net_device *dev) |
| { |
| struct amd8111e_priv *lp = netdev_priv(dev); |
| void __iomem *mmio = lp->mmio; |
| unsigned long flags; |
| struct net_device_stats *new_stats = &dev->stats; |
| |
| if (!lp->opened) |
| return new_stats; |
| spin_lock_irqsave(&lp->lock, flags); |
| |
| /* stats.rx_packets */ |
| new_stats->rx_packets = amd8111e_read_mib(mmio, rcv_broadcast_pkts)+ |
| amd8111e_read_mib(mmio, rcv_multicast_pkts)+ |
| amd8111e_read_mib(mmio, rcv_unicast_pkts); |
| |
| /* stats.tx_packets */ |
| new_stats->tx_packets = amd8111e_read_mib(mmio, xmt_packets); |
| |
| /*stats.rx_bytes */ |
| new_stats->rx_bytes = amd8111e_read_mib(mmio, rcv_octets); |
| |
| /* stats.tx_bytes */ |
| new_stats->tx_bytes = amd8111e_read_mib(mmio, xmt_octets); |
| |
| /* stats.rx_errors */ |
| /* hw errors + errors driver reported */ |
| new_stats->rx_errors = amd8111e_read_mib(mmio, rcv_undersize_pkts)+ |
| amd8111e_read_mib(mmio, rcv_fragments)+ |
| amd8111e_read_mib(mmio, rcv_jabbers)+ |
| amd8111e_read_mib(mmio, rcv_alignment_errors)+ |
| amd8111e_read_mib(mmio, rcv_fcs_errors)+ |
| amd8111e_read_mib(mmio, rcv_miss_pkts)+ |
| lp->drv_rx_errors; |
| |
| /* stats.tx_errors */ |
| new_stats->tx_errors = amd8111e_read_mib(mmio, xmt_underrun_pkts); |
| |
| /* stats.rx_dropped*/ |
| new_stats->rx_dropped = amd8111e_read_mib(mmio, rcv_miss_pkts); |
| |
| /* stats.tx_dropped*/ |
| new_stats->tx_dropped = amd8111e_read_mib(mmio, xmt_underrun_pkts); |
| |
| /* stats.multicast*/ |
| new_stats->multicast = amd8111e_read_mib(mmio, rcv_multicast_pkts); |
| |
| /* stats.collisions*/ |
| new_stats->collisions = amd8111e_read_mib(mmio, xmt_collisions); |
| |
| /* stats.rx_length_errors*/ |
| new_stats->rx_length_errors = |
| amd8111e_read_mib(mmio, rcv_undersize_pkts)+ |
| amd8111e_read_mib(mmio, rcv_oversize_pkts); |
| |
| /* stats.rx_over_errors*/ |
| new_stats->rx_over_errors = amd8111e_read_mib(mmio, rcv_miss_pkts); |
| |
| /* stats.rx_crc_errors*/ |
| new_stats->rx_crc_errors = amd8111e_read_mib(mmio, rcv_fcs_errors); |
| |
| /* stats.rx_frame_errors*/ |
| new_stats->rx_frame_errors = |
| amd8111e_read_mib(mmio, rcv_alignment_errors); |
| |
| /* stats.rx_fifo_errors */ |
| new_stats->rx_fifo_errors = amd8111e_read_mib(mmio, rcv_miss_pkts); |
| |
| /* stats.rx_missed_errors */ |
| new_stats->rx_missed_errors = amd8111e_read_mib(mmio, rcv_miss_pkts); |
| |
| /* stats.tx_aborted_errors*/ |
| new_stats->tx_aborted_errors = |
| amd8111e_read_mib(mmio, xmt_excessive_collision); |
| |
| /* stats.tx_carrier_errors*/ |
| new_stats->tx_carrier_errors = |
| amd8111e_read_mib(mmio, xmt_loss_carrier); |
| |
| /* stats.tx_fifo_errors*/ |
| new_stats->tx_fifo_errors = amd8111e_read_mib(mmio, xmt_underrun_pkts); |
| |
| /* stats.tx_window_errors*/ |
| new_stats->tx_window_errors = |
| amd8111e_read_mib(mmio, xmt_late_collision); |
| |
| /* Reset the mibs for collecting new statistics */ |
| /* writew(MIB_CLEAR, mmio + MIB_ADDR);*/ |
| |
| spin_unlock_irqrestore(&lp->lock, flags); |
| |
| return new_stats; |
| } |
| |
| /* This function recalculate the interrupt coalescing mode on every interrupt |
| * according to the datarate and the packet rate. |
| */ |
| static int amd8111e_calc_coalesce(struct net_device *dev) |
| { |
| struct amd8111e_priv *lp = netdev_priv(dev); |
| struct amd8111e_coalesce_conf *coal_conf = &lp->coal_conf; |
| int tx_pkt_rate; |
| int rx_pkt_rate; |
| int tx_data_rate; |
| int rx_data_rate; |
| int rx_pkt_size; |
| int tx_pkt_size; |
| |
| tx_pkt_rate = coal_conf->tx_packets - coal_conf->tx_prev_packets; |
| coal_conf->tx_prev_packets = coal_conf->tx_packets; |
| |
| tx_data_rate = coal_conf->tx_bytes - coal_conf->tx_prev_bytes; |
| coal_conf->tx_prev_bytes = coal_conf->tx_bytes; |
| |
| rx_pkt_rate = coal_conf->rx_packets - coal_conf->rx_prev_packets; |
| coal_conf->rx_prev_packets = coal_conf->rx_packets; |
| |
| rx_data_rate = coal_conf->rx_bytes - coal_conf->rx_prev_bytes; |
| coal_conf->rx_prev_bytes = coal_conf->rx_bytes; |
| |
| if (rx_pkt_rate < 800) { |
| if (coal_conf->rx_coal_type != NO_COALESCE) { |
| |
| coal_conf->rx_timeout = 0x0; |
| coal_conf->rx_event_count = 0; |
| amd8111e_set_coalesce(dev, RX_INTR_COAL); |
| coal_conf->rx_coal_type = NO_COALESCE; |
| } |
| } else { |
| |
| rx_pkt_size = rx_data_rate/rx_pkt_rate; |
| if (rx_pkt_size < 128) { |
| if (coal_conf->rx_coal_type != NO_COALESCE) { |
| |
| coal_conf->rx_timeout = 0; |
| coal_conf->rx_event_count = 0; |
| amd8111e_set_coalesce(dev, RX_INTR_COAL); |
| coal_conf->rx_coal_type = NO_COALESCE; |
| } |
| |
| } else if ((rx_pkt_size >= 128) && (rx_pkt_size < 512)) { |
| |
| if (coal_conf->rx_coal_type != LOW_COALESCE) { |
| coal_conf->rx_timeout = 1; |
| coal_conf->rx_event_count = 4; |
| amd8111e_set_coalesce(dev, RX_INTR_COAL); |
| coal_conf->rx_coal_type = LOW_COALESCE; |
| } |
| } else if ((rx_pkt_size >= 512) && (rx_pkt_size < 1024)) { |
| |
| if (coal_conf->rx_coal_type != MEDIUM_COALESCE) { |
| coal_conf->rx_timeout = 1; |
| coal_conf->rx_event_count = 4; |
| amd8111e_set_coalesce(dev, RX_INTR_COAL); |
| coal_conf->rx_coal_type = MEDIUM_COALESCE; |
| } |
| |
| } else if (rx_pkt_size >= 1024) { |
| |
| if (coal_conf->rx_coal_type != HIGH_COALESCE) { |
| coal_conf->rx_timeout = 2; |
| coal_conf->rx_event_count = 3; |
| amd8111e_set_coalesce(dev, RX_INTR_COAL); |
| coal_conf->rx_coal_type = HIGH_COALESCE; |
| } |
| } |
| } |
| /* NOW FOR TX INTR COALESC */ |
| if (tx_pkt_rate < 800) { |
| if (coal_conf->tx_coal_type != NO_COALESCE) { |
| |
| coal_conf->tx_timeout = 0x0; |
| coal_conf->tx_event_count = 0; |
| amd8111e_set_coalesce(dev, TX_INTR_COAL); |
| coal_conf->tx_coal_type = NO_COALESCE; |
| } |
| } else { |
| |
| tx_pkt_size = tx_data_rate/tx_pkt_rate; |
| if (tx_pkt_size < 128) { |
| |
| if (coal_conf->tx_coal_type != NO_COALESCE) { |
| |
| coal_conf->tx_timeout = 0; |
| coal_conf->tx_event_count = 0; |
| amd8111e_set_coalesce(dev, TX_INTR_COAL); |
| coal_conf->tx_coal_type = NO_COALESCE; |
| } |
| |
| } else if ((tx_pkt_size >= 128) && (tx_pkt_size < 512)) { |
| |
| if (coal_conf->tx_coal_type != LOW_COALESCE) { |
| coal_conf->tx_timeout = 1; |
| coal_conf->tx_event_count = 2; |
| amd8111e_set_coalesce(dev, TX_INTR_COAL); |
| coal_conf->tx_coal_type = LOW_COALESCE; |
| |
| } |
| } else if ((tx_pkt_size >= 512) && (tx_pkt_size < 1024)) { |
| |
| if (coal_conf->tx_coal_type != MEDIUM_COALESCE) { |
| coal_conf->tx_timeout = 2; |
| coal_conf->tx_event_count = 5; |
| amd8111e_set_coalesce(dev, TX_INTR_COAL); |
| coal_conf->tx_coal_type = MEDIUM_COALESCE; |
| } |
| } else if (tx_pkt_size >= 1024) { |
| if (coal_conf->tx_coal_type != HIGH_COALESCE) { |
| coal_conf->tx_timeout = 4; |
| coal_conf->tx_event_count = 8; |
| amd8111e_set_coalesce(dev, TX_INTR_COAL); |
| coal_conf->tx_coal_type = HIGH_COALESCE; |
| } |
| } |
| } |
| return 0; |
| |
| } |
| |
| /* This is device interrupt function. It handles transmit, |
| * receive,link change and hardware timer interrupts. |
| */ |
| static irqreturn_t amd8111e_interrupt(int irq, void *dev_id) |
| { |
| |
| struct net_device *dev = (struct net_device *)dev_id; |
| struct amd8111e_priv *lp = netdev_priv(dev); |
| void __iomem *mmio = lp->mmio; |
| unsigned int intr0, intren0; |
| unsigned int handled = 1; |
| |
| if (unlikely(dev == NULL)) |
| return IRQ_NONE; |
| |
| spin_lock(&lp->lock); |
| |
| /* disabling interrupt */ |
| writel(INTREN, mmio + CMD0); |
| |
| /* Read interrupt status */ |
| intr0 = readl(mmio + INT0); |
| intren0 = readl(mmio + INTEN0); |
| |
| /* Process all the INT event until INTR bit is clear. */ |
| |
| if (!(intr0 & INTR)) { |
| handled = 0; |
| goto err_no_interrupt; |
| } |
| |
| /* Current driver processes 4 interrupts : RINT,TINT,LCINT,STINT */ |
| writel(intr0, mmio + INT0); |
| |
| /* Check if Receive Interrupt has occurred. */ |
| if (intr0 & RINT0) { |
| if (napi_schedule_prep(&lp->napi)) { |
| /* Disable receive interupts */ |
| writel(RINTEN0, mmio + INTEN0); |
| /* Schedule a polling routine */ |
| __napi_schedule(&lp->napi); |
| } else if (intren0 & RINTEN0) { |
| netdev_dbg(dev, "************Driver bug! interrupt while in poll\n"); |
| /* Fix by disable receive interrupts */ |
| writel(RINTEN0, mmio + INTEN0); |
| } |
| } |
| |
| /* Check if Transmit Interrupt has occurred. */ |
| if (intr0 & TINT0) |
| amd8111e_tx(dev); |
| |
| /* Check if Link Change Interrupt has occurred. */ |
| if (intr0 & LCINT) |
| amd8111e_link_change(dev); |
| |
| /* Check if Hardware Timer Interrupt has occurred. */ |
| if (intr0 & STINT) |
| amd8111e_calc_coalesce(dev); |
| |
| err_no_interrupt: |
| writel(VAL0 | INTREN, mmio + CMD0); |
| |
| spin_unlock(&lp->lock); |
| |
| return IRQ_RETVAL(handled); |
| } |
| |
| #ifdef CONFIG_NET_POLL_CONTROLLER |
| static void amd8111e_poll(struct net_device *dev) |
| { |
| unsigned long flags; |
| local_irq_save(flags); |
| amd8111e_interrupt(0, dev); |
| local_irq_restore(flags); |
| } |
| #endif |
| |
| |
| /* This function closes the network interface and updates |
| * the statistics so that most recent statistics will be |
| * available after the interface is down. |
| */ |
| static int amd8111e_close(struct net_device *dev) |
| { |
| struct amd8111e_priv *lp = netdev_priv(dev); |
| netif_stop_queue(dev); |
| |
| napi_disable(&lp->napi); |
| |
| spin_lock_irq(&lp->lock); |
| |
| amd8111e_disable_interrupt(lp); |
| amd8111e_stop_chip(lp); |
| |
| /* Free transmit and receive skbs */ |
| amd8111e_free_skbs(lp->amd8111e_net_dev); |
| |
| netif_carrier_off(lp->amd8111e_net_dev); |
| |
| /* Delete ipg timer */ |
| if (lp->options & OPTION_DYN_IPG_ENABLE) |
| del_timer_sync(&lp->ipg_data.ipg_timer); |
| |
| spin_unlock_irq(&lp->lock); |
| free_irq(dev->irq, dev); |
| amd8111e_free_ring(lp); |
| |
| /* Update the statistics before closing */ |
| amd8111e_get_stats(dev); |
| lp->opened = 0; |
| return 0; |
| } |
| |
| /* This function opens new interface.It requests irq for the device, |
| * initializes the device,buffers and descriptors, and starts the device. |
| */ |
| static int amd8111e_open(struct net_device *dev) |
| { |
| struct amd8111e_priv *lp = netdev_priv(dev); |
| |
| if (dev->irq == 0 || request_irq(dev->irq, amd8111e_interrupt, |
| IRQF_SHARED, dev->name, dev)) |
| return -EAGAIN; |
| |
| napi_enable(&lp->napi); |
| |
| spin_lock_irq(&lp->lock); |
| |
| amd8111e_init_hw_default(lp); |
| |
| if (amd8111e_restart(dev)) { |
| spin_unlock_irq(&lp->lock); |
| napi_disable(&lp->napi); |
| if (dev->irq) |
| free_irq(dev->irq, dev); |
| return -ENOMEM; |
| } |
| /* Start ipg timer */ |
| if (lp->options & OPTION_DYN_IPG_ENABLE) { |
| add_timer(&lp->ipg_data.ipg_timer); |
| netdev_info(dev, "Dynamic IPG Enabled\n"); |
| } |
| |
| lp->opened = 1; |
| |
| spin_unlock_irq(&lp->lock); |
| |
| netif_start_queue(dev); |
| |
| return 0; |
| } |
| |
| /* This function checks if there is any transmit descriptors |
| * available to queue more packet. |
| */ |
| static int amd8111e_tx_queue_avail(struct amd8111e_priv *lp) |
| { |
| int tx_index = lp->tx_idx & TX_BUFF_MOD_MASK; |
| if (lp->tx_skbuff[tx_index]) |
| return -1; |
| else |
| return 0; |
| |
| } |
| |
| /* This function will queue the transmit packets to the |
| * descriptors and will trigger the send operation. It also |
| * initializes the transmit descriptors with buffer physical address, |
| * byte count, ownership to hardware etc. |
| */ |
| static netdev_tx_t amd8111e_start_xmit(struct sk_buff *skb, |
| struct net_device *dev) |
| { |
| struct amd8111e_priv *lp = netdev_priv(dev); |
| int tx_index; |
| unsigned long flags; |
| |
| spin_lock_irqsave(&lp->lock, flags); |
| |
| tx_index = lp->tx_idx & TX_RING_DR_MOD_MASK; |
| |
| lp->tx_ring[tx_index].buff_count = cpu_to_le16(skb->len); |
| |
| lp->tx_skbuff[tx_index] = skb; |
| lp->tx_ring[tx_index].tx_flags = 0; |
| |
| #if AMD8111E_VLAN_TAG_USED |
| if (skb_vlan_tag_present(skb)) { |
| lp->tx_ring[tx_index].tag_ctrl_cmd |= |
| cpu_to_le16(TCC_VLAN_INSERT); |
| lp->tx_ring[tx_index].tag_ctrl_info = |
| cpu_to_le16(skb_vlan_tag_get(skb)); |
| |
| } |
| #endif |
| lp->tx_dma_addr[tx_index] = |
| dma_map_single(&lp->pci_dev->dev, skb->data, skb->len, |
| DMA_TO_DEVICE); |
| lp->tx_ring[tx_index].buff_phy_addr = |
| cpu_to_le32(lp->tx_dma_addr[tx_index]); |
| |
| /* Set FCS and LTINT bits */ |
| wmb(); |
| lp->tx_ring[tx_index].tx_flags |= |
| cpu_to_le16(OWN_BIT | STP_BIT | ENP_BIT|ADD_FCS_BIT|LTINT_BIT); |
| |
| lp->tx_idx++; |
| |
| /* Trigger an immediate send poll. */ |
| writel(VAL1 | TDMD0, lp->mmio + CMD0); |
| writel(VAL2 | RDMD0, lp->mmio + CMD0); |
| |
| if (amd8111e_tx_queue_avail(lp) < 0) { |
| netif_stop_queue(dev); |
| } |
| spin_unlock_irqrestore(&lp->lock, flags); |
| return NETDEV_TX_OK; |
| } |
| /* This function returns all the memory mapped registers of the device. */ |
| static void amd8111e_read_regs(struct amd8111e_priv *lp, u32 *buf) |
| { |
| void __iomem *mmio = lp->mmio; |
| /* Read only necessary registers */ |
| buf[0] = readl(mmio + XMT_RING_BASE_ADDR0); |
| buf[1] = readl(mmio + XMT_RING_LEN0); |
| buf[2] = readl(mmio + RCV_RING_BASE_ADDR0); |
| buf[3] = readl(mmio + RCV_RING_LEN0); |
| buf[4] = readl(mmio + CMD0); |
| buf[5] = readl(mmio + CMD2); |
| buf[6] = readl(mmio + CMD3); |
| buf[7] = readl(mmio + CMD7); |
| buf[8] = readl(mmio + INT0); |
| buf[9] = readl(mmio + INTEN0); |
| buf[10] = readl(mmio + LADRF); |
| buf[11] = readl(mmio + LADRF+4); |
| buf[12] = readl(mmio + STAT0); |
| } |
| |
| |
| /* This function sets promiscuos mode, all-multi mode or the multicast address |
| * list to the device. |
| */ |
| static void amd8111e_set_multicast_list(struct net_device *dev) |
| { |
| struct netdev_hw_addr *ha; |
| struct amd8111e_priv *lp = netdev_priv(dev); |
| u32 mc_filter[2]; |
| int bit_num; |
| |
| if (dev->flags & IFF_PROMISC) { |
| writel(VAL2 | PROM, lp->mmio + CMD2); |
| return; |
| } |
| else |
| writel(PROM, lp->mmio + CMD2); |
| if (dev->flags & IFF_ALLMULTI || |
| netdev_mc_count(dev) > MAX_FILTER_SIZE) { |
| /* get all multicast packet */ |
| mc_filter[1] = mc_filter[0] = 0xffffffff; |
| lp->options |= OPTION_MULTICAST_ENABLE; |
| amd8111e_writeq(*(u64 *)mc_filter, lp->mmio + LADRF); |
| return; |
| } |
| if (netdev_mc_empty(dev)) { |
| /* get only own packets */ |
| mc_filter[1] = mc_filter[0] = 0; |
| lp->options &= ~OPTION_MULTICAST_ENABLE; |
| amd8111e_writeq(*(u64 *)mc_filter, lp->mmio + LADRF); |
| /* disable promiscuous mode */ |
| writel(PROM, lp->mmio + CMD2); |
| return; |
| } |
| /* load all the multicast addresses in the logic filter */ |
| lp->options |= OPTION_MULTICAST_ENABLE; |
| mc_filter[1] = mc_filter[0] = 0; |
| netdev_for_each_mc_addr(ha, dev) { |
| bit_num = (ether_crc_le(ETH_ALEN, ha->addr) >> 26) & 0x3f; |
| mc_filter[bit_num >> 5] |= 1 << (bit_num & 31); |
| } |
| amd8111e_writeq(*(u64 *)mc_filter, lp->mmio + LADRF); |
| |
| /* To eliminate PCI posting bug */ |
| readl(lp->mmio + CMD2); |
| |
| } |
| |
| static void amd8111e_get_drvinfo(struct net_device *dev, |
| struct ethtool_drvinfo *info) |
| { |
| struct amd8111e_priv *lp = netdev_priv(dev); |
| struct pci_dev *pci_dev = lp->pci_dev; |
| strlcpy(info->driver, MODULE_NAME, sizeof(info->driver)); |
| snprintf(info->fw_version, sizeof(info->fw_version), |
| "%u", chip_version); |
| strlcpy(info->bus_info, pci_name(pci_dev), sizeof(info->bus_info)); |
| } |
| |
| static int amd8111e_get_regs_len(struct net_device *dev) |
| { |
| return AMD8111E_REG_DUMP_LEN; |
| } |
| |
| static void amd8111e_get_regs(struct net_device *dev, struct ethtool_regs *regs, void *buf) |
| { |
| struct amd8111e_priv *lp = netdev_priv(dev); |
| regs->version = 0; |
| amd8111e_read_regs(lp, buf); |
| } |
| |
| static int amd8111e_get_link_ksettings(struct net_device *dev, |
| struct ethtool_link_ksettings *cmd) |
| { |
| struct amd8111e_priv *lp = netdev_priv(dev); |
| spin_lock_irq(&lp->lock); |
| mii_ethtool_get_link_ksettings(&lp->mii_if, cmd); |
| spin_unlock_irq(&lp->lock); |
| return 0; |
| } |
| |
| static int amd8111e_set_link_ksettings(struct net_device *dev, |
| const struct ethtool_link_ksettings *cmd) |
| { |
| struct amd8111e_priv *lp = netdev_priv(dev); |
| int res; |
| spin_lock_irq(&lp->lock); |
| res = mii_ethtool_set_link_ksettings(&lp->mii_if, cmd); |
| spin_unlock_irq(&lp->lock); |
| return res; |
| } |
| |
| static int amd8111e_nway_reset(struct net_device *dev) |
| { |
| struct amd8111e_priv *lp = netdev_priv(dev); |
| return mii_nway_restart(&lp->mii_if); |
| } |
| |
| static u32 amd8111e_get_link(struct net_device *dev) |
| { |
| struct amd8111e_priv *lp = netdev_priv(dev); |
| return mii_link_ok(&lp->mii_if); |
| } |
| |
| static void amd8111e_get_wol(struct net_device *dev, struct ethtool_wolinfo *wol_info) |
| { |
| struct amd8111e_priv *lp = netdev_priv(dev); |
| wol_info->supported = WAKE_MAGIC|WAKE_PHY; |
| if (lp->options & OPTION_WOL_ENABLE) |
| wol_info->wolopts = WAKE_MAGIC; |
| } |
| |
| static int amd8111e_set_wol(struct net_device *dev, struct ethtool_wolinfo *wol_info) |
| { |
| struct amd8111e_priv *lp = netdev_priv(dev); |
| if (wol_info->wolopts & ~(WAKE_MAGIC|WAKE_PHY)) |
| return -EINVAL; |
| spin_lock_irq(&lp->lock); |
| if (wol_info->wolopts & WAKE_MAGIC) |
| lp->options |= |
| (OPTION_WOL_ENABLE | OPTION_WAKE_MAGIC_ENABLE); |
| else if (wol_info->wolopts & WAKE_PHY) |
| lp->options |= |
| (OPTION_WOL_ENABLE | OPTION_WAKE_PHY_ENABLE); |
| else |
| lp->options &= ~OPTION_WOL_ENABLE; |
| spin_unlock_irq(&lp->lock); |
| return 0; |
| } |
| |
| static const struct ethtool_ops ops = { |
| .get_drvinfo = amd8111e_get_drvinfo, |
| .get_regs_len = amd8111e_get_regs_len, |
| .get_regs = amd8111e_get_regs, |
| .nway_reset = amd8111e_nway_reset, |
| .get_link = amd8111e_get_link, |
| .get_wol = amd8111e_get_wol, |
| .set_wol = amd8111e_set_wol, |
| .get_link_ksettings = amd8111e_get_link_ksettings, |
| .set_link_ksettings = amd8111e_set_link_ksettings, |
| }; |
| |
| /* This function handles all the ethtool ioctls. It gives driver info, |
| * gets/sets driver speed, gets memory mapped register values, forces |
| * auto negotiation, sets/gets WOL options for ethtool application. |
| */ |
| static int amd8111e_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd) |
| { |
| struct mii_ioctl_data *data = if_mii(ifr); |
| struct amd8111e_priv *lp = netdev_priv(dev); |
| int err; |
| u32 mii_regval; |
| |
| switch (cmd) { |
| case SIOCGMIIPHY: |
| data->phy_id = lp->ext_phy_addr; |
| |
| fallthrough; |
| case SIOCGMIIREG: |
| |
| spin_lock_irq(&lp->lock); |
| err = amd8111e_read_phy(lp, data->phy_id, |
| data->reg_num & PHY_REG_ADDR_MASK, &mii_regval); |
| spin_unlock_irq(&lp->lock); |
| |
| data->val_out = mii_regval; |
| return err; |
| |
| case SIOCSMIIREG: |
| |
| spin_lock_irq(&lp->lock); |
| err = amd8111e_write_phy(lp, data->phy_id, |
| data->reg_num & PHY_REG_ADDR_MASK, data->val_in); |
| spin_unlock_irq(&lp->lock); |
| |
| return err; |
| |
| default: |
| /* do nothing */ |
| break; |
| } |
| return -EOPNOTSUPP; |
| } |
| static int amd8111e_set_mac_address(struct net_device *dev, void *p) |
| { |
| struct amd8111e_priv *lp = netdev_priv(dev); |
| int i; |
| struct sockaddr *addr = p; |
| |
| eth_hw_addr_set(dev, addr->sa_data); |
| spin_lock_irq(&lp->lock); |
| /* Setting the MAC address to the device */ |
| for (i = 0; i < ETH_ALEN; i++) |
| writeb(dev->dev_addr[i], lp->mmio + PADR + i); |
| |
| spin_unlock_irq(&lp->lock); |
| |
| return 0; |
| } |
| |
| /* This function changes the mtu of the device. It restarts the device to |
| * initialize the descriptor with new receive buffers. |
| */ |
| static int amd8111e_change_mtu(struct net_device *dev, int new_mtu) |
| { |
| struct amd8111e_priv *lp = netdev_priv(dev); |
| int err; |
| |
| if (!netif_running(dev)) { |
| /* new_mtu will be used |
| * when device starts netxt time |
| */ |
| dev->mtu = new_mtu; |
| return 0; |
| } |
| |
| spin_lock_irq(&lp->lock); |
| |
| /* stop the chip */ |
| writel(RUN, lp->mmio + CMD0); |
| |
| dev->mtu = new_mtu; |
| |
| err = amd8111e_restart(dev); |
| spin_unlock_irq(&lp->lock); |
| if (!err) |
| netif_start_queue(dev); |
| return err; |
| } |
| |
| static int amd8111e_enable_magicpkt(struct amd8111e_priv *lp) |
| { |
| writel(VAL1 | MPPLBA, lp->mmio + CMD3); |
| writel(VAL0 | MPEN_SW, lp->mmio + CMD7); |
| |
| /* To eliminate PCI posting bug */ |
| readl(lp->mmio + CMD7); |
| return 0; |
| } |
| |
| static int amd8111e_enable_link_change(struct amd8111e_priv *lp) |
| { |
| |
| /* Adapter is already stoped/suspended/interrupt-disabled */ |
| writel(VAL0 | LCMODE_SW, lp->mmio + CMD7); |
| |
| /* To eliminate PCI posting bug */ |
| readl(lp->mmio + CMD7); |
| return 0; |
| } |
| |
| /* This function is called when a packet transmission fails to complete |
| * within a reasonable period, on the assumption that an interrupt have |
| * failed or the interface is locked up. This function will reinitialize |
| * the hardware. |
| */ |
| static void amd8111e_tx_timeout(struct net_device *dev, unsigned int txqueue) |
| { |
| struct amd8111e_priv *lp = netdev_priv(dev); |
| int err; |
| |
| netdev_err(dev, "transmit timed out, resetting\n"); |
| |
| spin_lock_irq(&lp->lock); |
| err = amd8111e_restart(dev); |
| spin_unlock_irq(&lp->lock); |
| if (!err) |
| netif_wake_queue(dev); |
| } |
| |
| static int __maybe_unused amd8111e_suspend(struct device *dev_d) |
| { |
| struct net_device *dev = dev_get_drvdata(dev_d); |
| struct amd8111e_priv *lp = netdev_priv(dev); |
| |
| if (!netif_running(dev)) |
| return 0; |
| |
| /* disable the interrupt */ |
| spin_lock_irq(&lp->lock); |
| amd8111e_disable_interrupt(lp); |
| spin_unlock_irq(&lp->lock); |
| |
| netif_device_detach(dev); |
| |
| /* stop chip */ |
| spin_lock_irq(&lp->lock); |
| if (lp->options & OPTION_DYN_IPG_ENABLE) |
| del_timer_sync(&lp->ipg_data.ipg_timer); |
| amd8111e_stop_chip(lp); |
| spin_unlock_irq(&lp->lock); |
| |
| if (lp->options & OPTION_WOL_ENABLE) { |
| /* enable wol */ |
| if (lp->options & OPTION_WAKE_MAGIC_ENABLE) |
| amd8111e_enable_magicpkt(lp); |
| if (lp->options & OPTION_WAKE_PHY_ENABLE) |
| amd8111e_enable_link_change(lp); |
| |
| device_set_wakeup_enable(dev_d, 1); |
| |
| } else { |
| device_set_wakeup_enable(dev_d, 0); |
| } |
| |
| return 0; |
| } |
| |
| static int __maybe_unused amd8111e_resume(struct device *dev_d) |
| { |
| struct net_device *dev = dev_get_drvdata(dev_d); |
| struct amd8111e_priv *lp = netdev_priv(dev); |
| |
| if (!netif_running(dev)) |
| return 0; |
| |
| netif_device_attach(dev); |
| |
| spin_lock_irq(&lp->lock); |
| amd8111e_restart(dev); |
| /* Restart ipg timer */ |
| if (lp->options & OPTION_DYN_IPG_ENABLE) |
| mod_timer(&lp->ipg_data.ipg_timer, |
| jiffies + IPG_CONVERGE_JIFFIES); |
| spin_unlock_irq(&lp->lock); |
| |
| return 0; |
| } |
| |
| static void amd8111e_config_ipg(struct timer_list *t) |
| { |
| struct amd8111e_priv *lp = from_timer(lp, t, ipg_data.ipg_timer); |
| struct ipg_info *ipg_data = &lp->ipg_data; |
| void __iomem *mmio = lp->mmio; |
| unsigned int prev_col_cnt = ipg_data->col_cnt; |
| unsigned int total_col_cnt; |
| unsigned int tmp_ipg; |
| |
| if (lp->link_config.duplex == DUPLEX_FULL) { |
| ipg_data->ipg = DEFAULT_IPG; |
| return; |
| } |
| |
| if (ipg_data->ipg_state == SSTATE) { |
| |
| if (ipg_data->timer_tick == IPG_STABLE_TIME) { |
| |
| ipg_data->timer_tick = 0; |
| ipg_data->ipg = MIN_IPG - IPG_STEP; |
| ipg_data->current_ipg = MIN_IPG; |
| ipg_data->diff_col_cnt = 0xFFFFFFFF; |
| ipg_data->ipg_state = CSTATE; |
| } |
| else |
| ipg_data->timer_tick++; |
| } |
| |
| if (ipg_data->ipg_state == CSTATE) { |
| |
| /* Get the current collision count */ |
| |
| total_col_cnt = ipg_data->col_cnt = |
| amd8111e_read_mib(mmio, xmt_collisions); |
| |
| if ((total_col_cnt - prev_col_cnt) < |
| (ipg_data->diff_col_cnt)) { |
| |
| ipg_data->diff_col_cnt = |
| total_col_cnt - prev_col_cnt; |
| |
| ipg_data->ipg = ipg_data->current_ipg; |
| } |
| |
| ipg_data->current_ipg += IPG_STEP; |
| |
| if (ipg_data->current_ipg <= MAX_IPG) |
| tmp_ipg = ipg_data->current_ipg; |
| else { |
| tmp_ipg = ipg_data->ipg; |
| ipg_data->ipg_state = SSTATE; |
| } |
| writew((u32)tmp_ipg, mmio + IPG); |
| writew((u32)(tmp_ipg - IFS1_DELTA), mmio + IFS1); |
| } |
| mod_timer(&lp->ipg_data.ipg_timer, jiffies + IPG_CONVERGE_JIFFIES); |
| return; |
| |
| } |
| |
| static void amd8111e_probe_ext_phy(struct net_device *dev) |
| { |
| struct amd8111e_priv *lp = netdev_priv(dev); |
| int i; |
| |
| for (i = 0x1e; i >= 0; i--) { |
| u32 id1, id2; |
| |
| if (amd8111e_read_phy(lp, i, MII_PHYSID1, &id1)) |
| continue; |
| if (amd8111e_read_phy(lp, i, MII_PHYSID2, &id2)) |
| continue; |
| lp->ext_phy_id = (id1 << 16) | id2; |
| lp->ext_phy_addr = i; |
| return; |
| } |
| lp->ext_phy_id = 0; |
| lp->ext_phy_addr = 1; |
| } |
| |
| static const struct net_device_ops amd8111e_netdev_ops = { |
| .ndo_open = amd8111e_open, |
| .ndo_stop = amd8111e_close, |
| .ndo_start_xmit = amd8111e_start_xmit, |
| .ndo_tx_timeout = amd8111e_tx_timeout, |
| .ndo_get_stats = amd8111e_get_stats, |
| .ndo_set_rx_mode = amd8111e_set_multicast_list, |
| .ndo_validate_addr = eth_validate_addr, |
| .ndo_set_mac_address = amd8111e_set_mac_address, |
| .ndo_eth_ioctl = amd8111e_ioctl, |
| .ndo_change_mtu = amd8111e_change_mtu, |
| #ifdef CONFIG_NET_POLL_CONTROLLER |
| .ndo_poll_controller = amd8111e_poll, |
| #endif |
| }; |
| |
| static int amd8111e_probe_one(struct pci_dev *pdev, |
| const struct pci_device_id *ent) |
| { |
| int err, i; |
| unsigned long reg_addr, reg_len; |
| struct amd8111e_priv *lp; |
| struct net_device *dev; |
| u8 addr[ETH_ALEN]; |
| |
| err = pci_enable_device(pdev); |
| if (err) { |
| dev_err(&pdev->dev, "Cannot enable new PCI device\n"); |
| return err; |
| } |
| |
| if (!(pci_resource_flags(pdev, 0) & IORESOURCE_MEM)) { |
| dev_err(&pdev->dev, "Cannot find PCI base address\n"); |
| err = -ENODEV; |
| goto err_disable_pdev; |
| } |
| |
| err = pci_request_regions(pdev, MODULE_NAME); |
| if (err) { |
| dev_err(&pdev->dev, "Cannot obtain PCI resources\n"); |
| goto err_disable_pdev; |
| } |
| |
| pci_set_master(pdev); |
| |
| /* Find power-management capability. */ |
| if (!pdev->pm_cap) { |
| dev_err(&pdev->dev, "No Power Management capability\n"); |
| err = -ENODEV; |
| goto err_free_reg; |
| } |
| |
| /* Initialize DMA */ |
| if (dma_set_mask(&pdev->dev, DMA_BIT_MASK(32)) < 0) { |
| dev_err(&pdev->dev, "DMA not supported\n"); |
| err = -ENODEV; |
| goto err_free_reg; |
| } |
| |
| reg_addr = pci_resource_start(pdev, 0); |
| reg_len = pci_resource_len(pdev, 0); |
| |
| dev = alloc_etherdev(sizeof(struct amd8111e_priv)); |
| if (!dev) { |
| err = -ENOMEM; |
| goto err_free_reg; |
| } |
| |
| SET_NETDEV_DEV(dev, &pdev->dev); |
| |
| #if AMD8111E_VLAN_TAG_USED |
| dev->features |= NETIF_F_HW_VLAN_CTAG_TX | NETIF_F_HW_VLAN_CTAG_RX; |
| #endif |
| |
| lp = netdev_priv(dev); |
| lp->pci_dev = pdev; |
| lp->amd8111e_net_dev = dev; |
| lp->pm_cap = pdev->pm_cap; |
| |
| spin_lock_init(&lp->lock); |
| |
| lp->mmio = devm_ioremap(&pdev->dev, reg_addr, reg_len); |
| if (!lp->mmio) { |
| dev_err(&pdev->dev, "Cannot map device registers\n"); |
| err = -ENOMEM; |
| goto err_free_dev; |
| } |
| |
| /* Initializing MAC address */ |
| for (i = 0; i < ETH_ALEN; i++) |
| addr[i] = readb(lp->mmio + PADR + i); |
| eth_hw_addr_set(dev, addr); |
| |
| /* Setting user defined parametrs */ |
| lp->ext_phy_option = speed_duplex[card_idx]; |
| if (coalesce[card_idx]) |
| lp->options |= OPTION_INTR_COAL_ENABLE; |
| if (dynamic_ipg[card_idx++]) |
| lp->options |= OPTION_DYN_IPG_ENABLE; |
| |
| |
| /* Initialize driver entry points */ |
| dev->netdev_ops = &amd8111e_netdev_ops; |
| dev->ethtool_ops = &ops; |
| dev->irq = pdev->irq; |
| dev->watchdog_timeo = AMD8111E_TX_TIMEOUT; |
| dev->min_mtu = AMD8111E_MIN_MTU; |
| dev->max_mtu = AMD8111E_MAX_MTU; |
| netif_napi_add(dev, &lp->napi, amd8111e_rx_poll, 32); |
| |
| #if AMD8111E_VLAN_TAG_USED |
| dev->features |= NETIF_F_HW_VLAN_CTAG_TX | NETIF_F_HW_VLAN_CTAG_RX; |
| #endif |
| /* Probe the external PHY */ |
| amd8111e_probe_ext_phy(dev); |
| |
| /* setting mii default values */ |
| lp->mii_if.dev = dev; |
| lp->mii_if.mdio_read = amd8111e_mdio_read; |
| lp->mii_if.mdio_write = amd8111e_mdio_write; |
| lp->mii_if.phy_id = lp->ext_phy_addr; |
| |
| /* Set receive buffer length and set jumbo option*/ |
| amd8111e_set_rx_buff_len(dev); |
| |
| |
| err = register_netdev(dev); |
| if (err) { |
| dev_err(&pdev->dev, "Cannot register net device\n"); |
| goto err_free_dev; |
| } |
| |
| pci_set_drvdata(pdev, dev); |
| |
| /* Initialize software ipg timer */ |
| if (lp->options & OPTION_DYN_IPG_ENABLE) { |
| timer_setup(&lp->ipg_data.ipg_timer, amd8111e_config_ipg, 0); |
| lp->ipg_data.ipg_timer.expires = jiffies + |
| IPG_CONVERGE_JIFFIES; |
| lp->ipg_data.ipg = DEFAULT_IPG; |
| lp->ipg_data.ipg_state = CSTATE; |
| } |
| |
| /* display driver and device information */ |
| chip_version = (readl(lp->mmio + CHIPID) & 0xf0000000) >> 28; |
| dev_info(&pdev->dev, "[ Rev %x ] PCI 10/100BaseT Ethernet %pM\n", |
| chip_version, dev->dev_addr); |
| if (lp->ext_phy_id) |
| dev_info(&pdev->dev, "Found MII PHY ID 0x%08x at address 0x%02x\n", |
| lp->ext_phy_id, lp->ext_phy_addr); |
| else |
| dev_info(&pdev->dev, "Couldn't detect MII PHY, assuming address 0x01\n"); |
| |
| return 0; |
| |
| err_free_dev: |
| free_netdev(dev); |
| |
| err_free_reg: |
| pci_release_regions(pdev); |
| |
| err_disable_pdev: |
| pci_disable_device(pdev); |
| return err; |
| |
| } |
| |
| static void amd8111e_remove_one(struct pci_dev *pdev) |
| { |
| struct net_device *dev = pci_get_drvdata(pdev); |
| |
| if (dev) { |
| unregister_netdev(dev); |
| free_netdev(dev); |
| pci_release_regions(pdev); |
| pci_disable_device(pdev); |
| } |
| } |
| |
| static const struct pci_device_id amd8111e_pci_tbl[] = { |
| { |
| .vendor = PCI_VENDOR_ID_AMD, |
| .device = PCI_DEVICE_ID_AMD8111E_7462, |
| }, |
| { |
| .vendor = 0, |
| } |
| }; |
| MODULE_DEVICE_TABLE(pci, amd8111e_pci_tbl); |
| |
| static SIMPLE_DEV_PM_OPS(amd8111e_pm_ops, amd8111e_suspend, amd8111e_resume); |
| |
| static struct pci_driver amd8111e_driver = { |
| .name = MODULE_NAME, |
| .id_table = amd8111e_pci_tbl, |
| .probe = amd8111e_probe_one, |
| .remove = amd8111e_remove_one, |
| .driver.pm = &amd8111e_pm_ops |
| }; |
| |
| module_pci_driver(amd8111e_driver); |