| // SPDX-License-Identifier: GPL-2.0-or-later |
| /* |
| * Driver for Silicon Labs Si2161 DVB-T and Si2165 DVB-C/-T Demodulator |
| * |
| * Copyright (C) 2013-2017 Matthias Schwarzott <zzam@gentoo.org> |
| * |
| * References: |
| * https://www.silabs.com/Support%20Documents/TechnicalDocs/Si2165-short.pdf |
| */ |
| |
| #include <linux/delay.h> |
| #include <linux/errno.h> |
| #include <linux/init.h> |
| #include <linux/kernel.h> |
| #include <linux/module.h> |
| #include <linux/string.h> |
| #include <linux/slab.h> |
| #include <linux/firmware.h> |
| #include <linux/regmap.h> |
| |
| #include <media/dvb_frontend.h> |
| #include <linux/int_log.h> |
| #include "si2165_priv.h" |
| #include "si2165.h" |
| |
| /* |
| * Hauppauge WinTV-HVR-930C-HD B130 / PCTV QuatroStick 521e 1113xx |
| * uses 16 MHz xtal |
| * |
| * Hauppauge WinTV-HVR-930C-HD B131 / PCTV QuatroStick 522e 1114xx |
| * uses 24 MHz clock provided by tuner |
| */ |
| |
| struct si2165_state { |
| struct i2c_client *client; |
| |
| struct regmap *regmap; |
| |
| struct dvb_frontend fe; |
| |
| struct si2165_config config; |
| |
| u8 chip_revcode; |
| u8 chip_type; |
| |
| /* calculated by xtal and div settings */ |
| u32 fvco_hz; |
| u32 sys_clk; |
| u32 adc_clk; |
| |
| /* DVBv3 stats */ |
| u64 ber_prev; |
| |
| bool has_dvbc; |
| bool has_dvbt; |
| bool firmware_loaded; |
| }; |
| |
| static int si2165_write(struct si2165_state *state, const u16 reg, |
| const u8 *src, const int count) |
| { |
| int ret; |
| |
| dev_dbg(&state->client->dev, "i2c write: reg: 0x%04x, data: %*ph\n", |
| reg, count, src); |
| |
| ret = regmap_bulk_write(state->regmap, reg, src, count); |
| |
| if (ret) |
| dev_err(&state->client->dev, "%s: ret == %d\n", __func__, ret); |
| |
| return ret; |
| } |
| |
| static int si2165_read(struct si2165_state *state, |
| const u16 reg, u8 *val, const int count) |
| { |
| int ret = regmap_bulk_read(state->regmap, reg, val, count); |
| |
| if (ret) { |
| dev_err(&state->client->dev, "%s: error (addr %02x reg %04x error (ret == %i)\n", |
| __func__, state->config.i2c_addr, reg, ret); |
| return ret; |
| } |
| |
| dev_dbg(&state->client->dev, "i2c read: reg: 0x%04x, data: %*ph\n", |
| reg, count, val); |
| |
| return 0; |
| } |
| |
| static int si2165_readreg8(struct si2165_state *state, |
| const u16 reg, u8 *val) |
| { |
| unsigned int val_tmp; |
| int ret = regmap_read(state->regmap, reg, &val_tmp); |
| *val = (u8)val_tmp; |
| dev_dbg(&state->client->dev, "reg read: R(0x%04x)=0x%02x\n", reg, *val); |
| return ret; |
| } |
| |
| static int si2165_readreg16(struct si2165_state *state, |
| const u16 reg, u16 *val) |
| { |
| u8 buf[2]; |
| |
| int ret = si2165_read(state, reg, buf, 2); |
| *val = buf[0] | buf[1] << 8; |
| dev_dbg(&state->client->dev, "reg read: R(0x%04x)=0x%04x\n", reg, *val); |
| return ret; |
| } |
| |
| static int si2165_readreg24(struct si2165_state *state, |
| const u16 reg, u32 *val) |
| { |
| u8 buf[3]; |
| |
| int ret = si2165_read(state, reg, buf, 3); |
| *val = buf[0] | buf[1] << 8 | buf[2] << 16; |
| dev_dbg(&state->client->dev, "reg read: R(0x%04x)=0x%06x\n", reg, *val); |
| return ret; |
| } |
| |
| static int si2165_writereg8(struct si2165_state *state, const u16 reg, u8 val) |
| { |
| return regmap_write(state->regmap, reg, val); |
| } |
| |
| static int si2165_writereg16(struct si2165_state *state, const u16 reg, u16 val) |
| { |
| u8 buf[2] = { val & 0xff, (val >> 8) & 0xff }; |
| |
| return si2165_write(state, reg, buf, 2); |
| } |
| |
| static int si2165_writereg24(struct si2165_state *state, const u16 reg, u32 val) |
| { |
| u8 buf[3] = { val & 0xff, (val >> 8) & 0xff, (val >> 16) & 0xff }; |
| |
| return si2165_write(state, reg, buf, 3); |
| } |
| |
| static int si2165_writereg32(struct si2165_state *state, const u16 reg, u32 val) |
| { |
| u8 buf[4] = { |
| val & 0xff, |
| (val >> 8) & 0xff, |
| (val >> 16) & 0xff, |
| (val >> 24) & 0xff |
| }; |
| return si2165_write(state, reg, buf, 4); |
| } |
| |
| static int si2165_writereg_mask8(struct si2165_state *state, const u16 reg, |
| u8 val, u8 mask) |
| { |
| if (mask != 0xff) { |
| u8 tmp; |
| int ret = si2165_readreg8(state, reg, &tmp); |
| |
| if (ret < 0) |
| return ret; |
| |
| val &= mask; |
| tmp &= ~mask; |
| val |= tmp; |
| } |
| return si2165_writereg8(state, reg, val); |
| } |
| |
| #define REG16(reg, val) \ |
| { (reg), (val) & 0xff }, \ |
| { (reg) + 1, (val) >> 8 & 0xff } |
| struct si2165_reg_value_pair { |
| u16 reg; |
| u8 val; |
| }; |
| |
| static int si2165_write_reg_list(struct si2165_state *state, |
| const struct si2165_reg_value_pair *regs, |
| int count) |
| { |
| int i; |
| int ret; |
| |
| for (i = 0; i < count; i++) { |
| ret = si2165_writereg8(state, regs[i].reg, regs[i].val); |
| if (ret < 0) |
| return ret; |
| } |
| return 0; |
| } |
| |
| static int si2165_get_tune_settings(struct dvb_frontend *fe, |
| struct dvb_frontend_tune_settings *s) |
| { |
| s->min_delay_ms = 1000; |
| return 0; |
| } |
| |
| static int si2165_init_pll(struct si2165_state *state) |
| { |
| u32 ref_freq_hz = state->config.ref_freq_hz; |
| u8 divr = 1; /* 1..7 */ |
| u8 divp = 1; /* only 1 or 4 */ |
| u8 divn = 56; /* 1..63 */ |
| u8 divm = 8; |
| u8 divl = 12; |
| u8 buf[4]; |
| |
| /* |
| * hardcoded values can be deleted if calculation is verified |
| * or it yields the same values as the windows driver |
| */ |
| switch (ref_freq_hz) { |
| case 16000000u: |
| divn = 56; |
| break; |
| case 24000000u: |
| divr = 2; |
| divp = 4; |
| divn = 19; |
| break; |
| default: |
| /* ref_freq / divr must be between 4 and 16 MHz */ |
| if (ref_freq_hz > 16000000u) |
| divr = 2; |
| |
| /* |
| * now select divn and divp such that |
| * fvco is in 1624..1824 MHz |
| */ |
| if (1624000000u * divr > ref_freq_hz * 2u * 63u) |
| divp = 4; |
| |
| /* is this already correct regarding rounding? */ |
| divn = 1624000000u * divr / (ref_freq_hz * 2u * divp); |
| break; |
| } |
| |
| /* adc_clk and sys_clk depend on xtal and pll settings */ |
| state->fvco_hz = ref_freq_hz / divr |
| * 2u * divn * divp; |
| state->adc_clk = state->fvco_hz / (divm * 4u); |
| state->sys_clk = state->fvco_hz / (divl * 2u); |
| |
| /* write all 4 pll registers 0x00a0..0x00a3 at once */ |
| buf[0] = divl; |
| buf[1] = divm; |
| buf[2] = (divn & 0x3f) | ((divp == 1) ? 0x40 : 0x00) | 0x80; |
| buf[3] = divr; |
| return si2165_write(state, REG_PLL_DIVL, buf, 4); |
| } |
| |
| static int si2165_adjust_pll_divl(struct si2165_state *state, u8 divl) |
| { |
| state->sys_clk = state->fvco_hz / (divl * 2u); |
| return si2165_writereg8(state, REG_PLL_DIVL, divl); |
| } |
| |
| static u32 si2165_get_fe_clk(struct si2165_state *state) |
| { |
| /* assume Oversampling mode Ovr4 is used */ |
| return state->adc_clk; |
| } |
| |
| static int si2165_wait_init_done(struct si2165_state *state) |
| { |
| int ret; |
| u8 val = 0; |
| int i; |
| |
| for (i = 0; i < 3; ++i) { |
| ret = si2165_readreg8(state, REG_INIT_DONE, &val); |
| if (ret < 0) |
| return ret; |
| if (val == 0x01) |
| return 0; |
| usleep_range(1000, 50000); |
| } |
| dev_err(&state->client->dev, "init_done was not set\n"); |
| return -EINVAL; |
| } |
| |
| static int si2165_upload_firmware_block(struct si2165_state *state, |
| const u8 *data, u32 len, u32 *poffset, |
| u32 block_count) |
| { |
| int ret; |
| u8 buf_ctrl[4] = { 0x00, 0x00, 0x00, 0xc0 }; |
| u8 wordcount; |
| u32 cur_block = 0; |
| u32 offset = poffset ? *poffset : 0; |
| |
| if (len < 4) |
| return -EINVAL; |
| if (len % 4 != 0) |
| return -EINVAL; |
| |
| dev_dbg(&state->client->dev, |
| "fw load: %s: called with len=0x%x offset=0x%x blockcount=0x%x\n", |
| __func__, len, offset, block_count); |
| while (offset + 12 <= len && cur_block < block_count) { |
| dev_dbg(&state->client->dev, |
| "fw load: %s: in while len=0x%x offset=0x%x cur_block=0x%x blockcount=0x%x\n", |
| __func__, len, offset, cur_block, block_count); |
| wordcount = data[offset]; |
| if (wordcount < 1 || data[offset + 1] || |
| data[offset + 2] || data[offset + 3]) { |
| dev_warn(&state->client->dev, |
| "bad fw data[0..3] = %*ph\n", |
| 4, data); |
| return -EINVAL; |
| } |
| |
| if (offset + 8 + wordcount * 4 > len) { |
| dev_warn(&state->client->dev, |
| "len is too small for block len=%d, wordcount=%d\n", |
| len, wordcount); |
| return -EINVAL; |
| } |
| |
| buf_ctrl[0] = wordcount - 1; |
| |
| ret = si2165_write(state, REG_DCOM_CONTROL_BYTE, buf_ctrl, 4); |
| if (ret < 0) |
| goto error; |
| ret = si2165_write(state, REG_DCOM_ADDR, data + offset + 4, 4); |
| if (ret < 0) |
| goto error; |
| |
| offset += 8; |
| |
| while (wordcount > 0) { |
| ret = si2165_write(state, REG_DCOM_DATA, |
| data + offset, 4); |
| if (ret < 0) |
| goto error; |
| wordcount--; |
| offset += 4; |
| } |
| cur_block++; |
| } |
| |
| dev_dbg(&state->client->dev, |
| "fw load: %s: after while len=0x%x offset=0x%x cur_block=0x%x blockcount=0x%x\n", |
| __func__, len, offset, cur_block, block_count); |
| |
| if (poffset) |
| *poffset = offset; |
| |
| dev_dbg(&state->client->dev, |
| "fw load: %s: returned offset=0x%x\n", |
| __func__, offset); |
| |
| return 0; |
| error: |
| return ret; |
| } |
| |
| static int si2165_upload_firmware(struct si2165_state *state) |
| { |
| /* int ret; */ |
| u8 val[3]; |
| u16 val16; |
| int ret; |
| |
| const struct firmware *fw = NULL; |
| u8 *fw_file; |
| const u8 *data; |
| u32 len; |
| u32 offset; |
| u8 patch_version; |
| u8 block_count; |
| u16 crc_expected; |
| |
| switch (state->chip_revcode) { |
| case 0x03: /* revision D */ |
| fw_file = SI2165_FIRMWARE_REV_D; |
| break; |
| default: |
| dev_info(&state->client->dev, "no firmware file for revision=%d\n", |
| state->chip_revcode); |
| return 0; |
| } |
| |
| /* request the firmware, this will block and timeout */ |
| ret = request_firmware(&fw, fw_file, &state->client->dev); |
| if (ret) { |
| dev_warn(&state->client->dev, "firmware file '%s' not found\n", |
| fw_file); |
| goto error; |
| } |
| |
| data = fw->data; |
| len = fw->size; |
| |
| dev_info(&state->client->dev, "downloading firmware from file '%s' size=%d\n", |
| fw_file, len); |
| |
| if (len % 4 != 0) { |
| dev_warn(&state->client->dev, "firmware size is not multiple of 4\n"); |
| ret = -EINVAL; |
| goto error; |
| } |
| |
| /* check header (8 bytes) */ |
| if (len < 8) { |
| dev_warn(&state->client->dev, "firmware header is missing\n"); |
| ret = -EINVAL; |
| goto error; |
| } |
| |
| if (data[0] != 1 || data[1] != 0) { |
| dev_warn(&state->client->dev, "firmware file version is wrong\n"); |
| ret = -EINVAL; |
| goto error; |
| } |
| |
| patch_version = data[2]; |
| block_count = data[4]; |
| crc_expected = data[7] << 8 | data[6]; |
| |
| /* start uploading fw */ |
| /* boot/wdog status */ |
| ret = si2165_writereg8(state, REG_WDOG_AND_BOOT, 0x00); |
| if (ret < 0) |
| goto error; |
| /* reset */ |
| ret = si2165_writereg8(state, REG_RST_ALL, 0x00); |
| if (ret < 0) |
| goto error; |
| /* boot/wdog status */ |
| ret = si2165_readreg8(state, REG_WDOG_AND_BOOT, val); |
| if (ret < 0) |
| goto error; |
| |
| /* enable reset on error */ |
| ret = si2165_readreg8(state, REG_EN_RST_ERROR, val); |
| if (ret < 0) |
| goto error; |
| ret = si2165_readreg8(state, REG_EN_RST_ERROR, val); |
| if (ret < 0) |
| goto error; |
| ret = si2165_writereg8(state, REG_EN_RST_ERROR, 0x02); |
| if (ret < 0) |
| goto error; |
| |
| /* start right after the header */ |
| offset = 8; |
| |
| dev_info(&state->client->dev, "%s: extracted patch_version=0x%02x, block_count=0x%02x, crc_expected=0x%04x\n", |
| __func__, patch_version, block_count, crc_expected); |
| |
| ret = si2165_upload_firmware_block(state, data, len, &offset, 1); |
| if (ret < 0) |
| goto error; |
| |
| ret = si2165_writereg8(state, REG_PATCH_VERSION, patch_version); |
| if (ret < 0) |
| goto error; |
| |
| /* reset crc */ |
| ret = si2165_writereg8(state, REG_RST_CRC, 0x01); |
| if (ret) |
| goto error; |
| |
| ret = si2165_upload_firmware_block(state, data, len, |
| &offset, block_count); |
| if (ret < 0) { |
| dev_err(&state->client->dev, |
| "firmware could not be uploaded\n"); |
| goto error; |
| } |
| |
| /* read crc */ |
| ret = si2165_readreg16(state, REG_CRC, &val16); |
| if (ret) |
| goto error; |
| |
| if (val16 != crc_expected) { |
| dev_err(&state->client->dev, |
| "firmware crc mismatch %04x != %04x\n", |
| val16, crc_expected); |
| ret = -EINVAL; |
| goto error; |
| } |
| |
| ret = si2165_upload_firmware_block(state, data, len, &offset, 5); |
| if (ret) |
| goto error; |
| |
| if (len != offset) { |
| dev_err(&state->client->dev, |
| "firmware len mismatch %04x != %04x\n", |
| len, offset); |
| ret = -EINVAL; |
| goto error; |
| } |
| |
| /* reset watchdog error register */ |
| ret = si2165_writereg_mask8(state, REG_WDOG_AND_BOOT, 0x02, 0x02); |
| if (ret < 0) |
| goto error; |
| |
| /* enable reset on error */ |
| ret = si2165_writereg_mask8(state, REG_EN_RST_ERROR, 0x01, 0x01); |
| if (ret < 0) |
| goto error; |
| |
| dev_info(&state->client->dev, "fw load finished\n"); |
| |
| ret = 0; |
| state->firmware_loaded = true; |
| error: |
| release_firmware(fw); |
| fw = NULL; |
| |
| return ret; |
| } |
| |
| static int si2165_init(struct dvb_frontend *fe) |
| { |
| int ret = 0; |
| struct si2165_state *state = fe->demodulator_priv; |
| struct dtv_frontend_properties *c = &fe->dtv_property_cache; |
| u8 val; |
| u8 patch_version = 0x00; |
| |
| dev_dbg(&state->client->dev, "%s: called\n", __func__); |
| |
| /* powerup */ |
| ret = si2165_writereg8(state, REG_CHIP_MODE, state->config.chip_mode); |
| if (ret < 0) |
| goto error; |
| /* dsp_clock_enable */ |
| ret = si2165_writereg8(state, REG_DSP_CLOCK, 0x01); |
| if (ret < 0) |
| goto error; |
| /* verify chip_mode */ |
| ret = si2165_readreg8(state, REG_CHIP_MODE, &val); |
| if (ret < 0) |
| goto error; |
| if (val != state->config.chip_mode) { |
| dev_err(&state->client->dev, "could not set chip_mode\n"); |
| return -EINVAL; |
| } |
| |
| /* agc */ |
| ret = si2165_writereg8(state, REG_AGC_IF_TRI, 0x00); |
| if (ret < 0) |
| goto error; |
| ret = si2165_writereg8(state, REG_AGC_IF_SLR, 0x01); |
| if (ret < 0) |
| goto error; |
| ret = si2165_writereg8(state, REG_AGC2_OUTPUT, 0x00); |
| if (ret < 0) |
| goto error; |
| ret = si2165_writereg8(state, REG_AGC2_CLKDIV, 0x07); |
| if (ret < 0) |
| goto error; |
| /* rssi pad */ |
| ret = si2165_writereg8(state, REG_RSSI_PAD_CTRL, 0x00); |
| if (ret < 0) |
| goto error; |
| ret = si2165_writereg8(state, REG_RSSI_ENABLE, 0x00); |
| if (ret < 0) |
| goto error; |
| |
| ret = si2165_init_pll(state); |
| if (ret < 0) |
| goto error; |
| |
| /* enable chip_init */ |
| ret = si2165_writereg8(state, REG_CHIP_INIT, 0x01); |
| if (ret < 0) |
| goto error; |
| /* set start_init */ |
| ret = si2165_writereg8(state, REG_START_INIT, 0x01); |
| if (ret < 0) |
| goto error; |
| ret = si2165_wait_init_done(state); |
| if (ret < 0) |
| goto error; |
| |
| /* disable chip_init */ |
| ret = si2165_writereg8(state, REG_CHIP_INIT, 0x00); |
| if (ret < 0) |
| goto error; |
| |
| /* ber_pkt - default 65535 */ |
| ret = si2165_writereg16(state, REG_BER_PKT, |
| STATISTICS_PERIOD_PKT_COUNT); |
| if (ret < 0) |
| goto error; |
| |
| ret = si2165_readreg8(state, REG_PATCH_VERSION, &patch_version); |
| if (ret < 0) |
| goto error; |
| |
| ret = si2165_writereg8(state, REG_AUTO_RESET, 0x00); |
| if (ret < 0) |
| goto error; |
| |
| /* dsp_addr_jump */ |
| ret = si2165_writereg32(state, REG_ADDR_JUMP, 0xf4000000); |
| if (ret < 0) |
| goto error; |
| /* boot/wdog status */ |
| ret = si2165_readreg8(state, REG_WDOG_AND_BOOT, &val); |
| if (ret < 0) |
| goto error; |
| |
| if (patch_version == 0x00) { |
| ret = si2165_upload_firmware(state); |
| if (ret < 0) |
| goto error; |
| } |
| |
| /* ts output config */ |
| ret = si2165_writereg8(state, REG_TS_DATA_MODE, 0x20); |
| if (ret < 0) |
| return ret; |
| ret = si2165_writereg16(state, REG_TS_TRI, 0x00fe); |
| if (ret < 0) |
| return ret; |
| ret = si2165_writereg24(state, REG_TS_SLR, 0x555555); |
| if (ret < 0) |
| return ret; |
| ret = si2165_writereg8(state, REG_TS_CLK_MODE, 0x01); |
| if (ret < 0) |
| return ret; |
| ret = si2165_writereg8(state, REG_TS_PARALLEL_MODE, 0x00); |
| if (ret < 0) |
| return ret; |
| |
| c = &state->fe.dtv_property_cache; |
| c->cnr.len = 1; |
| c->cnr.stat[0].scale = FE_SCALE_NOT_AVAILABLE; |
| c->post_bit_error.len = 1; |
| c->post_bit_error.stat[0].scale = FE_SCALE_NOT_AVAILABLE; |
| c->post_bit_count.len = 1; |
| c->post_bit_count.stat[0].scale = FE_SCALE_NOT_AVAILABLE; |
| |
| return 0; |
| error: |
| return ret; |
| } |
| |
| static int si2165_sleep(struct dvb_frontend *fe) |
| { |
| int ret; |
| struct si2165_state *state = fe->demodulator_priv; |
| |
| /* dsp clock disable */ |
| ret = si2165_writereg8(state, REG_DSP_CLOCK, 0x00); |
| if (ret < 0) |
| return ret; |
| /* chip mode */ |
| ret = si2165_writereg8(state, REG_CHIP_MODE, SI2165_MODE_OFF); |
| if (ret < 0) |
| return ret; |
| return 0; |
| } |
| |
| static int si2165_read_status(struct dvb_frontend *fe, enum fe_status *status) |
| { |
| int ret; |
| u8 u8tmp; |
| u32 u32tmp; |
| struct si2165_state *state = fe->demodulator_priv; |
| struct dtv_frontend_properties *c = &fe->dtv_property_cache; |
| u32 delsys = c->delivery_system; |
| |
| *status = 0; |
| |
| switch (delsys) { |
| case SYS_DVBT: |
| /* check fast signal type */ |
| ret = si2165_readreg8(state, REG_CHECK_SIGNAL, &u8tmp); |
| if (ret < 0) |
| return ret; |
| switch (u8tmp & 0x3) { |
| case 0: /* searching */ |
| case 1: /* nothing */ |
| break; |
| case 2: /* digital signal */ |
| *status |= FE_HAS_SIGNAL | FE_HAS_CARRIER; |
| break; |
| } |
| break; |
| case SYS_DVBC_ANNEX_A: |
| /* check packet sync lock */ |
| ret = si2165_readreg8(state, REG_PS_LOCK, &u8tmp); |
| if (ret < 0) |
| return ret; |
| if (u8tmp & 0x01) { |
| *status |= FE_HAS_SIGNAL; |
| *status |= FE_HAS_CARRIER; |
| *status |= FE_HAS_VITERBI; |
| *status |= FE_HAS_SYNC; |
| } |
| break; |
| } |
| |
| /* check fec_lock */ |
| ret = si2165_readreg8(state, REG_FEC_LOCK, &u8tmp); |
| if (ret < 0) |
| return ret; |
| if (u8tmp & 0x01) { |
| *status |= FE_HAS_SIGNAL; |
| *status |= FE_HAS_CARRIER; |
| *status |= FE_HAS_VITERBI; |
| *status |= FE_HAS_SYNC; |
| *status |= FE_HAS_LOCK; |
| } |
| |
| /* CNR */ |
| if (delsys == SYS_DVBC_ANNEX_A && *status & FE_HAS_VITERBI) { |
| ret = si2165_readreg24(state, REG_C_N, &u32tmp); |
| if (ret < 0) |
| return ret; |
| /* |
| * svalue = |
| * 1000 * c_n/dB = |
| * 1000 * 10 * log10(2^24 / regval) = |
| * 1000 * 10 * (log10(2^24) - log10(regval)) = |
| * 1000 * 10 * (intlog10(2^24) - intlog10(regval)) / 2^24 |
| * |
| * intlog10(x) = log10(x) * 2^24 |
| * intlog10(2^24) = log10(2^24) * 2^24 = 121210686 |
| */ |
| u32tmp = (1000 * 10 * (121210686 - (u64)intlog10(u32tmp))) |
| >> 24; |
| c->cnr.stat[0].scale = FE_SCALE_DECIBEL; |
| c->cnr.stat[0].svalue = u32tmp; |
| } else |
| c->cnr.stat[0].scale = FE_SCALE_NOT_AVAILABLE; |
| |
| /* BER */ |
| if (*status & FE_HAS_VITERBI) { |
| if (c->post_bit_error.stat[0].scale == FE_SCALE_NOT_AVAILABLE) { |
| /* start new sampling period to get rid of old data*/ |
| ret = si2165_writereg8(state, REG_BER_RST, 0x01); |
| if (ret < 0) |
| return ret; |
| |
| /* set scale to enter read code on next call */ |
| c->post_bit_error.stat[0].scale = FE_SCALE_COUNTER; |
| c->post_bit_count.stat[0].scale = FE_SCALE_COUNTER; |
| c->post_bit_error.stat[0].uvalue = 0; |
| c->post_bit_count.stat[0].uvalue = 0; |
| |
| /* |
| * reset DVBv3 value to deliver a good result |
| * for the first call |
| */ |
| state->ber_prev = 0; |
| |
| } else { |
| ret = si2165_readreg8(state, REG_BER_AVAIL, &u8tmp); |
| if (ret < 0) |
| return ret; |
| |
| if (u8tmp & 1) { |
| u32 biterrcnt; |
| |
| ret = si2165_readreg24(state, REG_BER_BIT, |
| &biterrcnt); |
| if (ret < 0) |
| return ret; |
| |
| c->post_bit_error.stat[0].uvalue += |
| biterrcnt; |
| c->post_bit_count.stat[0].uvalue += |
| STATISTICS_PERIOD_BIT_COUNT; |
| |
| /* start new sampling period */ |
| ret = si2165_writereg8(state, |
| REG_BER_RST, 0x01); |
| if (ret < 0) |
| return ret; |
| |
| dev_dbg(&state->client->dev, |
| "post_bit_error=%u post_bit_count=%u\n", |
| biterrcnt, STATISTICS_PERIOD_BIT_COUNT); |
| } |
| } |
| } else { |
| c->post_bit_error.stat[0].scale = FE_SCALE_NOT_AVAILABLE; |
| c->post_bit_count.stat[0].scale = FE_SCALE_NOT_AVAILABLE; |
| } |
| |
| return 0; |
| } |
| |
| static int si2165_read_snr(struct dvb_frontend *fe, u16 *snr) |
| { |
| struct dtv_frontend_properties *c = &fe->dtv_property_cache; |
| |
| if (c->cnr.stat[0].scale == FE_SCALE_DECIBEL) |
| *snr = div_s64(c->cnr.stat[0].svalue, 100); |
| else |
| *snr = 0; |
| return 0; |
| } |
| |
| static int si2165_read_ber(struct dvb_frontend *fe, u32 *ber) |
| { |
| struct si2165_state *state = fe->demodulator_priv; |
| struct dtv_frontend_properties *c = &fe->dtv_property_cache; |
| |
| if (c->post_bit_error.stat[0].scale != FE_SCALE_COUNTER) { |
| *ber = 0; |
| return 0; |
| } |
| |
| *ber = c->post_bit_error.stat[0].uvalue - state->ber_prev; |
| state->ber_prev = c->post_bit_error.stat[0].uvalue; |
| |
| return 0; |
| } |
| |
| static int si2165_set_oversamp(struct si2165_state *state, u32 dvb_rate) |
| { |
| u64 oversamp; |
| u32 reg_value; |
| |
| if (!dvb_rate) |
| return -EINVAL; |
| |
| oversamp = si2165_get_fe_clk(state); |
| oversamp <<= 23; |
| do_div(oversamp, dvb_rate); |
| reg_value = oversamp & 0x3fffffff; |
| |
| dev_dbg(&state->client->dev, "Write oversamp=%#x\n", reg_value); |
| return si2165_writereg32(state, REG_OVERSAMP, reg_value); |
| } |
| |
| static int si2165_set_if_freq_shift(struct si2165_state *state) |
| { |
| struct dvb_frontend *fe = &state->fe; |
| u64 if_freq_shift; |
| s32 reg_value = 0; |
| u32 fe_clk = si2165_get_fe_clk(state); |
| u32 IF = 0; |
| |
| if (!fe->ops.tuner_ops.get_if_frequency) { |
| dev_err(&state->client->dev, |
| "Error: get_if_frequency() not defined at tuner. Can't work without it!\n"); |
| return -EINVAL; |
| } |
| |
| if (!fe_clk) |
| return -EINVAL; |
| |
| fe->ops.tuner_ops.get_if_frequency(fe, &IF); |
| if_freq_shift = IF; |
| if_freq_shift <<= 29; |
| |
| do_div(if_freq_shift, fe_clk); |
| reg_value = (s32)if_freq_shift; |
| |
| if (state->config.inversion) |
| reg_value = -reg_value; |
| |
| reg_value = reg_value & 0x1fffffff; |
| |
| /* if_freq_shift, usbdump contained 0x023ee08f; */ |
| return si2165_writereg32(state, REG_IF_FREQ_SHIFT, reg_value); |
| } |
| |
| static const struct si2165_reg_value_pair dvbt_regs[] = { |
| /* standard = DVB-T */ |
| { REG_DVB_STANDARD, 0x01 }, |
| /* impulsive_noise_remover */ |
| { REG_IMPULSIVE_NOISE_REM, 0x01 }, |
| { REG_AUTO_RESET, 0x00 }, |
| /* agc2 */ |
| { REG_AGC2_MIN, 0x41 }, |
| { REG_AGC2_KACQ, 0x0e }, |
| { REG_AGC2_KLOC, 0x10 }, |
| /* agc */ |
| { REG_AGC_UNFREEZE_THR, 0x03 }, |
| { REG_AGC_CRESTF_DBX8, 0x78 }, |
| /* agc */ |
| { REG_AAF_CRESTF_DBX8, 0x78 }, |
| { REG_ACI_CRESTF_DBX8, 0x68 }, |
| /* freq_sync_range */ |
| REG16(REG_FREQ_SYNC_RANGE, 0x0064), |
| /* gp_reg0 */ |
| { REG_GP_REG0_MSB, 0x00 } |
| }; |
| |
| static int si2165_set_frontend_dvbt(struct dvb_frontend *fe) |
| { |
| int ret; |
| struct dtv_frontend_properties *p = &fe->dtv_property_cache; |
| struct si2165_state *state = fe->demodulator_priv; |
| u32 dvb_rate = 0; |
| u16 bw10k; |
| u32 bw_hz = p->bandwidth_hz; |
| |
| dev_dbg(&state->client->dev, "%s: called\n", __func__); |
| |
| if (!state->has_dvbt) |
| return -EINVAL; |
| |
| /* no bandwidth auto-detection */ |
| if (bw_hz == 0) |
| return -EINVAL; |
| |
| dvb_rate = bw_hz * 8 / 7; |
| bw10k = bw_hz / 10000; |
| |
| ret = si2165_adjust_pll_divl(state, 12); |
| if (ret < 0) |
| return ret; |
| |
| /* bandwidth in 10KHz steps */ |
| ret = si2165_writereg16(state, REG_T_BANDWIDTH, bw10k); |
| if (ret < 0) |
| return ret; |
| ret = si2165_set_oversamp(state, dvb_rate); |
| if (ret < 0) |
| return ret; |
| |
| ret = si2165_write_reg_list(state, dvbt_regs, ARRAY_SIZE(dvbt_regs)); |
| if (ret < 0) |
| return ret; |
| |
| return 0; |
| } |
| |
| static const struct si2165_reg_value_pair dvbc_regs[] = { |
| /* standard = DVB-C */ |
| { REG_DVB_STANDARD, 0x05 }, |
| |
| /* agc2 */ |
| { REG_AGC2_MIN, 0x50 }, |
| { REG_AGC2_KACQ, 0x0e }, |
| { REG_AGC2_KLOC, 0x10 }, |
| /* agc */ |
| { REG_AGC_UNFREEZE_THR, 0x03 }, |
| { REG_AGC_CRESTF_DBX8, 0x68 }, |
| /* agc */ |
| { REG_AAF_CRESTF_DBX8, 0x68 }, |
| { REG_ACI_CRESTF_DBX8, 0x50 }, |
| |
| { REG_EQ_AUTO_CONTROL, 0x0d }, |
| |
| { REG_KP_LOCK, 0x05 }, |
| { REG_CENTRAL_TAP, 0x09 }, |
| REG16(REG_UNKNOWN_350, 0x3e80), |
| |
| { REG_AUTO_RESET, 0x01 }, |
| REG16(REG_UNKNOWN_24C, 0x0000), |
| REG16(REG_UNKNOWN_27C, 0x0000), |
| { REG_SWEEP_STEP, 0x03 }, |
| { REG_AGC_IF_TRI, 0x00 }, |
| }; |
| |
| static int si2165_set_frontend_dvbc(struct dvb_frontend *fe) |
| { |
| struct si2165_state *state = fe->demodulator_priv; |
| int ret; |
| struct dtv_frontend_properties *p = &fe->dtv_property_cache; |
| const u32 dvb_rate = p->symbol_rate; |
| u8 u8tmp; |
| |
| if (!state->has_dvbc) |
| return -EINVAL; |
| |
| if (dvb_rate == 0) |
| return -EINVAL; |
| |
| ret = si2165_adjust_pll_divl(state, 14); |
| if (ret < 0) |
| return ret; |
| |
| /* Oversampling */ |
| ret = si2165_set_oversamp(state, dvb_rate); |
| if (ret < 0) |
| return ret; |
| |
| switch (p->modulation) { |
| case QPSK: |
| u8tmp = 0x3; |
| break; |
| case QAM_16: |
| u8tmp = 0x7; |
| break; |
| case QAM_32: |
| u8tmp = 0x8; |
| break; |
| case QAM_64: |
| u8tmp = 0x9; |
| break; |
| case QAM_128: |
| u8tmp = 0xa; |
| break; |
| case QAM_256: |
| default: |
| u8tmp = 0xb; |
| break; |
| } |
| ret = si2165_writereg8(state, REG_REQ_CONSTELLATION, u8tmp); |
| if (ret < 0) |
| return ret; |
| |
| ret = si2165_writereg32(state, REG_LOCK_TIMEOUT, 0x007a1200); |
| if (ret < 0) |
| return ret; |
| |
| ret = si2165_write_reg_list(state, dvbc_regs, ARRAY_SIZE(dvbc_regs)); |
| if (ret < 0) |
| return ret; |
| |
| return 0; |
| } |
| |
| static const struct si2165_reg_value_pair adc_rewrite[] = { |
| { REG_ADC_RI1, 0x46 }, |
| { REG_ADC_RI3, 0x00 }, |
| { REG_ADC_RI5, 0x0a }, |
| { REG_ADC_RI6, 0xff }, |
| { REG_ADC_RI8, 0x70 } |
| }; |
| |
| static int si2165_set_frontend(struct dvb_frontend *fe) |
| { |
| struct si2165_state *state = fe->demodulator_priv; |
| struct dtv_frontend_properties *p = &fe->dtv_property_cache; |
| u32 delsys = p->delivery_system; |
| int ret; |
| u8 val[3]; |
| |
| /* initial setting of if freq shift */ |
| ret = si2165_set_if_freq_shift(state); |
| if (ret < 0) |
| return ret; |
| |
| switch (delsys) { |
| case SYS_DVBT: |
| ret = si2165_set_frontend_dvbt(fe); |
| if (ret < 0) |
| return ret; |
| break; |
| case SYS_DVBC_ANNEX_A: |
| ret = si2165_set_frontend_dvbc(fe); |
| if (ret < 0) |
| return ret; |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| /* dsp_addr_jump */ |
| ret = si2165_writereg32(state, REG_ADDR_JUMP, 0xf4000000); |
| if (ret < 0) |
| return ret; |
| |
| if (fe->ops.tuner_ops.set_params) |
| fe->ops.tuner_ops.set_params(fe); |
| |
| /* recalc if_freq_shift if IF might has changed */ |
| ret = si2165_set_if_freq_shift(state); |
| if (ret < 0) |
| return ret; |
| |
| /* boot/wdog status */ |
| ret = si2165_readreg8(state, REG_WDOG_AND_BOOT, val); |
| if (ret < 0) |
| return ret; |
| ret = si2165_writereg8(state, REG_WDOG_AND_BOOT, 0x00); |
| if (ret < 0) |
| return ret; |
| |
| /* reset all */ |
| ret = si2165_writereg8(state, REG_RST_ALL, 0x00); |
| if (ret < 0) |
| return ret; |
| /* gp_reg0 */ |
| ret = si2165_writereg32(state, REG_GP_REG0_LSB, 0x00000000); |
| if (ret < 0) |
| return ret; |
| |
| /* write adc values after each reset*/ |
| ret = si2165_write_reg_list(state, adc_rewrite, |
| ARRAY_SIZE(adc_rewrite)); |
| if (ret < 0) |
| return ret; |
| |
| /* start_synchro */ |
| ret = si2165_writereg8(state, REG_START_SYNCHRO, 0x01); |
| if (ret < 0) |
| return ret; |
| /* boot/wdog status */ |
| ret = si2165_readreg8(state, REG_WDOG_AND_BOOT, val); |
| if (ret < 0) |
| return ret; |
| |
| return 0; |
| } |
| |
| static const struct dvb_frontend_ops si2165_ops = { |
| .info = { |
| .name = "Silicon Labs ", |
| /* For DVB-C */ |
| .symbol_rate_min = 1000000, |
| .symbol_rate_max = 7200000, |
| /* For DVB-T */ |
| .frequency_stepsize_hz = 166667, |
| .caps = FE_CAN_FEC_1_2 | |
| FE_CAN_FEC_2_3 | |
| FE_CAN_FEC_3_4 | |
| FE_CAN_FEC_5_6 | |
| FE_CAN_FEC_7_8 | |
| FE_CAN_FEC_AUTO | |
| FE_CAN_QPSK | |
| FE_CAN_QAM_16 | |
| FE_CAN_QAM_32 | |
| FE_CAN_QAM_64 | |
| FE_CAN_QAM_128 | |
| FE_CAN_QAM_256 | |
| FE_CAN_GUARD_INTERVAL_AUTO | |
| FE_CAN_HIERARCHY_AUTO | |
| FE_CAN_MUTE_TS | |
| FE_CAN_TRANSMISSION_MODE_AUTO | |
| FE_CAN_RECOVER |
| }, |
| |
| .get_tune_settings = si2165_get_tune_settings, |
| |
| .init = si2165_init, |
| .sleep = si2165_sleep, |
| |
| .set_frontend = si2165_set_frontend, |
| .read_status = si2165_read_status, |
| .read_snr = si2165_read_snr, |
| .read_ber = si2165_read_ber, |
| }; |
| |
| static int si2165_probe(struct i2c_client *client) |
| { |
| struct si2165_state *state = NULL; |
| struct si2165_platform_data *pdata = client->dev.platform_data; |
| int n; |
| int ret = 0; |
| u8 val; |
| char rev_char; |
| const char *chip_name; |
| static const struct regmap_config regmap_config = { |
| .reg_bits = 16, |
| .val_bits = 8, |
| .max_register = 0x08ff, |
| }; |
| |
| /* allocate memory for the internal state */ |
| state = kzalloc(sizeof(*state), GFP_KERNEL); |
| if (!state) { |
| ret = -ENOMEM; |
| goto error; |
| } |
| |
| /* create regmap */ |
| state->regmap = devm_regmap_init_i2c(client, ®map_config); |
| if (IS_ERR(state->regmap)) { |
| ret = PTR_ERR(state->regmap); |
| goto error; |
| } |
| |
| /* setup the state */ |
| state->client = client; |
| state->config.i2c_addr = client->addr; |
| state->config.chip_mode = pdata->chip_mode; |
| state->config.ref_freq_hz = pdata->ref_freq_hz; |
| state->config.inversion = pdata->inversion; |
| |
| if (state->config.ref_freq_hz < 4000000 || |
| state->config.ref_freq_hz > 27000000) { |
| dev_err(&state->client->dev, "ref_freq of %d Hz not supported by this driver\n", |
| state->config.ref_freq_hz); |
| ret = -EINVAL; |
| goto error; |
| } |
| |
| /* create dvb_frontend */ |
| memcpy(&state->fe.ops, &si2165_ops, |
| sizeof(struct dvb_frontend_ops)); |
| state->fe.ops.release = NULL; |
| state->fe.demodulator_priv = state; |
| i2c_set_clientdata(client, state); |
| |
| /* powerup */ |
| ret = si2165_writereg8(state, REG_CHIP_MODE, state->config.chip_mode); |
| if (ret < 0) |
| goto nodev_error; |
| |
| ret = si2165_readreg8(state, REG_CHIP_MODE, &val); |
| if (ret < 0) |
| goto nodev_error; |
| if (val != state->config.chip_mode) |
| goto nodev_error; |
| |
| ret = si2165_readreg8(state, REG_CHIP_REVCODE, &state->chip_revcode); |
| if (ret < 0) |
| goto nodev_error; |
| |
| ret = si2165_readreg8(state, REV_CHIP_TYPE, &state->chip_type); |
| if (ret < 0) |
| goto nodev_error; |
| |
| /* powerdown */ |
| ret = si2165_writereg8(state, REG_CHIP_MODE, SI2165_MODE_OFF); |
| if (ret < 0) |
| goto nodev_error; |
| |
| if (state->chip_revcode < 26) |
| rev_char = 'A' + state->chip_revcode; |
| else |
| rev_char = '?'; |
| |
| switch (state->chip_type) { |
| case 0x06: |
| chip_name = "Si2161"; |
| state->has_dvbt = true; |
| break; |
| case 0x07: |
| chip_name = "Si2165"; |
| state->has_dvbt = true; |
| state->has_dvbc = true; |
| break; |
| default: |
| dev_err(&state->client->dev, "Unsupported Silicon Labs chip (type %d, rev %d)\n", |
| state->chip_type, state->chip_revcode); |
| goto nodev_error; |
| } |
| |
| dev_info(&state->client->dev, |
| "Detected Silicon Labs %s-%c (type %d, rev %d)\n", |
| chip_name, rev_char, state->chip_type, |
| state->chip_revcode); |
| |
| strlcat(state->fe.ops.info.name, chip_name, |
| sizeof(state->fe.ops.info.name)); |
| |
| n = 0; |
| if (state->has_dvbt) { |
| state->fe.ops.delsys[n++] = SYS_DVBT; |
| strlcat(state->fe.ops.info.name, " DVB-T", |
| sizeof(state->fe.ops.info.name)); |
| } |
| if (state->has_dvbc) { |
| state->fe.ops.delsys[n++] = SYS_DVBC_ANNEX_A; |
| strlcat(state->fe.ops.info.name, " DVB-C", |
| sizeof(state->fe.ops.info.name)); |
| } |
| |
| /* return fe pointer */ |
| *pdata->fe = &state->fe; |
| |
| return 0; |
| |
| nodev_error: |
| ret = -ENODEV; |
| error: |
| kfree(state); |
| dev_dbg(&client->dev, "failed=%d\n", ret); |
| return ret; |
| } |
| |
| static void si2165_remove(struct i2c_client *client) |
| { |
| struct si2165_state *state = i2c_get_clientdata(client); |
| |
| dev_dbg(&client->dev, "\n"); |
| |
| kfree(state); |
| } |
| |
| static const struct i2c_device_id si2165_id_table[] = { |
| { "si2165" }, |
| {} |
| }; |
| MODULE_DEVICE_TABLE(i2c, si2165_id_table); |
| |
| static struct i2c_driver si2165_driver = { |
| .driver = { |
| .name = "si2165", |
| }, |
| .probe = si2165_probe, |
| .remove = si2165_remove, |
| .id_table = si2165_id_table, |
| }; |
| |
| module_i2c_driver(si2165_driver); |
| |
| MODULE_DESCRIPTION("Silicon Labs Si2165 DVB-C/-T Demodulator driver"); |
| MODULE_AUTHOR("Matthias Schwarzott <zzam@gentoo.org>"); |
| MODULE_LICENSE("GPL"); |
| MODULE_FIRMWARE(SI2165_FIRMWARE_REV_D); |