| Kernel driver tps53679 |
| ====================== |
| |
| Supported chips: |
| |
| * Texas Instruments TPS53647 |
| |
| Prefix: 'tps53647' |
| |
| Addresses scanned: - |
| |
| Datasheet: https://www.ti.com/lit/gpn/tps53647 |
| |
| * Texas Instruments TPS53667 |
| |
| Prefix: 'tps53667' |
| |
| Addresses scanned: - |
| |
| Datasheet: https://www.ti.com/lit/gpn/TPS53667 |
| |
| * Texas Instruments TPS53676 |
| |
| Prefix: 'tps53676' |
| |
| Addresses scanned: - |
| |
| Datasheet: https://www.ti.com/lit/gpn/TPS53676 |
| |
| * Texas Instruments TPS53679 |
| |
| Prefix: 'tps53679' |
| |
| Addresses scanned: - |
| |
| Datasheet: https://www.ti.com/lit/gpn/TPS53679 (short version) |
| |
| * Texas Instruments TPS53681 |
| |
| Prefix: 'tps53681' |
| |
| Addresses scanned: - |
| |
| Datasheet: https://www.ti.com/lit/gpn/TPS53681 |
| |
| * Texas Instruments TPS53688 |
| |
| Prefix: 'tps53688' |
| |
| Addresses scanned: - |
| |
| Datasheet: Available under NDA |
| |
| |
| Authors: |
| Vadim Pasternak <vadimp@mellanox.com> |
| Guenter Roeck <linux@roeck-us.net> |
| |
| |
| Description |
| ----------- |
| |
| Chips in this series are multi-phase step-down converters with one or two |
| output channels and up to 8 phases per channel. |
| |
| |
| Usage Notes |
| ----------- |
| |
| This driver does not probe for PMBus devices. You will have to instantiate |
| devices explicitly. |
| |
| Example: the following commands will load the driver for an TPS53681 at address |
| 0x60 on I2C bus #1:: |
| |
| # modprobe tps53679 |
| # echo tps53681 0x60 > /sys/bus/i2c/devices/i2c-1/new_device |
| |
| |
| Sysfs attributes |
| ---------------- |
| |
| ======================= ======================================================== |
| in1_label "vin" |
| |
| in1_input Measured input voltage. |
| |
| in1_lcrit Critical minimum input voltage |
| |
| TPS53679, TPS53681, TPS53688 only. |
| |
| in1_lcrit_alarm Input voltage critical low alarm. |
| |
| TPS53679, TPS53681, TPS53688 only. |
| |
| in1_crit Critical maximum input voltage. |
| |
| in1_crit_alarm Input voltage critical high alarm. |
| |
| in[N]_label "vout[1-2]" |
| |
| - TPS53647, TPS53667: N=2 |
| - TPS53679, TPS53588: N=2,3 |
| |
| in[N]_input Measured output voltage. |
| |
| in[N]_lcrit Critical minimum input voltage. |
| |
| TPS53679, TPS53681, TPS53688 only. |
| |
| in[N]_lcrit_alarm Critical minimum voltage alarm. |
| |
| TPS53679, TPS53681, TPS53688 only. |
| |
| in[N]_alarm Output voltage alarm. |
| |
| TPS53647, TPS53667 only. |
| |
| in[N]_crit Critical maximum output voltage. |
| |
| TPS53679, TPS53681, TPS53688 only. |
| |
| in[N]_crit_alarm Output voltage critical high alarm. |
| |
| TPS53679, TPS53681, TPS53688 only. |
| |
| temp[N]_input Measured temperature. |
| |
| - TPS53647, TPS53667: N=1 |
| - TPS53679, TPS53681, TPS53588: N=1,2 |
| |
| temp[N]_max Maximum temperature. |
| |
| temp[N]_crit Critical high temperature. |
| |
| temp[N]_max_alarm Temperature high alarm. |
| |
| temp[N]_crit_alarm Temperature critical high alarm. |
| |
| power1_label "pin". |
| |
| power1_input Measured input power. |
| |
| power[N]_label "pout[1-2]". |
| |
| - TPS53647, TPS53667: N=2 |
| - TPS53676, TPS53679, TPS53681, TPS53588: N=2,3 |
| |
| power[N]_input Measured output power. |
| |
| curr1_label "iin". |
| |
| curr1_input Measured input current. |
| |
| curr1_max Maximum input current. |
| |
| curr1_max_alarm Input current high alarm. |
| |
| curr1_crit Critical input current. |
| |
| curr1_crit_alarm Input current critical alarm. |
| |
| curr[N]_label "iout[1-2]" or "iout1.[0-5]". |
| |
| The first digit is the output channel, the second |
| digit is the phase within the channel. Per-phase |
| telemetry supported on TPS53676 and TPS53681 only. |
| |
| - TPS53647, TPS53667: N=2 |
| - TPS53679, TPS53588: N=2,3 |
| - TPS53676: N=2-8 |
| - TPS53681: N=2-9 |
| |
| curr[N]_input Measured output current. |
| |
| curr[N]_max Maximum output current. |
| |
| curr[N]_crit Critical high output current. |
| |
| curr[N]_max_alarm Output current high alarm. |
| |
| curr[N]_crit_alarm Output current critical high alarm. |
| |
| Limit and alarm attributes are only available for |
| non-phase telemetry (iout1, iout2). |
| |
| ======================= ======================================================== |
