| // SPDX-License-Identifier: BSD-3-Clause |
| /* |
| * Copyright (c) 2020, The Linux Foundation. All rights reserved. |
| */ |
| |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| #include <dt-bindings/clock/qcom,gcc-sm8250.h> |
| #include <dt-bindings/clock/qcom,gpucc-sm8250.h> |
| #include <dt-bindings/clock/qcom,rpmh.h> |
| #include <dt-bindings/interconnect/qcom,osm-l3.h> |
| #include <dt-bindings/mailbox/qcom-ipcc.h> |
| #include <dt-bindings/power/qcom-aoss-qmp.h> |
| #include <dt-bindings/power/qcom-rpmpd.h> |
| #include <dt-bindings/soc/qcom,rpmh-rsc.h> |
| #include <dt-bindings/thermal/thermal.h> |
| |
| / { |
| interrupt-parent = <&intc>; |
| |
| #address-cells = <2>; |
| #size-cells = <2>; |
| |
| aliases { |
| i2c0 = &i2c0; |
| i2c1 = &i2c1; |
| i2c2 = &i2c2; |
| i2c3 = &i2c3; |
| i2c4 = &i2c4; |
| i2c5 = &i2c5; |
| i2c6 = &i2c6; |
| i2c7 = &i2c7; |
| i2c8 = &i2c8; |
| i2c9 = &i2c9; |
| i2c10 = &i2c10; |
| i2c11 = &i2c11; |
| i2c12 = &i2c12; |
| i2c13 = &i2c13; |
| i2c14 = &i2c14; |
| i2c15 = &i2c15; |
| i2c16 = &i2c16; |
| i2c17 = &i2c17; |
| i2c18 = &i2c18; |
| i2c19 = &i2c19; |
| spi0 = &spi0; |
| spi1 = &spi1; |
| spi2 = &spi2; |
| spi3 = &spi3; |
| spi4 = &spi4; |
| spi5 = &spi5; |
| spi6 = &spi6; |
| spi7 = &spi7; |
| spi8 = &spi8; |
| spi9 = &spi9; |
| spi10 = &spi10; |
| spi11 = &spi11; |
| spi12 = &spi12; |
| spi13 = &spi13; |
| spi14 = &spi14; |
| spi15 = &spi15; |
| spi16 = &spi16; |
| spi17 = &spi17; |
| spi18 = &spi18; |
| spi19 = &spi19; |
| }; |
| |
| chosen { }; |
| |
| clocks { |
| xo_board: xo-board { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <38400000>; |
| clock-output-names = "xo_board"; |
| }; |
| |
| sleep_clk: sleep-clk { |
| compatible = "fixed-clock"; |
| clock-frequency = <32768>; |
| #clock-cells = <0>; |
| }; |
| }; |
| |
| cpus { |
| #address-cells = <2>; |
| #size-cells = <0>; |
| |
| CPU0: cpu@0 { |
| device_type = "cpu"; |
| compatible = "qcom,kryo485"; |
| reg = <0x0 0x0>; |
| enable-method = "psci"; |
| next-level-cache = <&L2_0>; |
| qcom,freq-domain = <&cpufreq_hw 0>; |
| #cooling-cells = <2>; |
| L2_0: l2-cache { |
| compatible = "cache"; |
| next-level-cache = <&L3_0>; |
| L3_0: l3-cache { |
| compatible = "cache"; |
| }; |
| }; |
| }; |
| |
| CPU1: cpu@100 { |
| device_type = "cpu"; |
| compatible = "qcom,kryo485"; |
| reg = <0x0 0x100>; |
| enable-method = "psci"; |
| next-level-cache = <&L2_100>; |
| qcom,freq-domain = <&cpufreq_hw 0>; |
| #cooling-cells = <2>; |
| L2_100: l2-cache { |
| compatible = "cache"; |
| next-level-cache = <&L3_0>; |
| }; |
| }; |
| |
| CPU2: cpu@200 { |
| device_type = "cpu"; |
| compatible = "qcom,kryo485"; |
| reg = <0x0 0x200>; |
| enable-method = "psci"; |
| next-level-cache = <&L2_200>; |
| qcom,freq-domain = <&cpufreq_hw 0>; |
| #cooling-cells = <2>; |
| L2_200: l2-cache { |
| compatible = "cache"; |
| next-level-cache = <&L3_0>; |
| }; |
| }; |
| |
| CPU3: cpu@300 { |
| device_type = "cpu"; |
| compatible = "qcom,kryo485"; |
| reg = <0x0 0x300>; |
| enable-method = "psci"; |
| next-level-cache = <&L2_300>; |
| qcom,freq-domain = <&cpufreq_hw 0>; |
| #cooling-cells = <2>; |
| L2_300: l2-cache { |
| compatible = "cache"; |
| next-level-cache = <&L3_0>; |
| }; |
| }; |
| |
| CPU4: cpu@400 { |
| device_type = "cpu"; |
| compatible = "qcom,kryo485"; |
| reg = <0x0 0x400>; |
| enable-method = "psci"; |
| next-level-cache = <&L2_400>; |
| qcom,freq-domain = <&cpufreq_hw 1>; |
| #cooling-cells = <2>; |
| L2_400: l2-cache { |
| compatible = "cache"; |
| next-level-cache = <&L3_0>; |
| }; |
| }; |
| |
| CPU5: cpu@500 { |
| device_type = "cpu"; |
| compatible = "qcom,kryo485"; |
| reg = <0x0 0x500>; |
| enable-method = "psci"; |
| next-level-cache = <&L2_500>; |
| qcom,freq-domain = <&cpufreq_hw 1>; |
| #cooling-cells = <2>; |
| L2_500: l2-cache { |
| compatible = "cache"; |
| next-level-cache = <&L3_0>; |
| }; |
| |
| }; |
| |
| CPU6: cpu@600 { |
| device_type = "cpu"; |
| compatible = "qcom,kryo485"; |
| reg = <0x0 0x600>; |
| enable-method = "psci"; |
| next-level-cache = <&L2_600>; |
| qcom,freq-domain = <&cpufreq_hw 1>; |
| #cooling-cells = <2>; |
| L2_600: l2-cache { |
| compatible = "cache"; |
| next-level-cache = <&L3_0>; |
| }; |
| }; |
| |
| CPU7: cpu@700 { |
| device_type = "cpu"; |
| compatible = "qcom,kryo485"; |
| reg = <0x0 0x700>; |
| enable-method = "psci"; |
| next-level-cache = <&L2_700>; |
| qcom,freq-domain = <&cpufreq_hw 2>; |
| #cooling-cells = <2>; |
| L2_700: l2-cache { |
| compatible = "cache"; |
| next-level-cache = <&L3_0>; |
| }; |
| }; |
| }; |
| |
| firmware { |
| scm: scm { |
| compatible = "qcom,scm"; |
| #reset-cells = <1>; |
| }; |
| }; |
| |
| memory@80000000 { |
| device_type = "memory"; |
| /* We expect the bootloader to fill in the size */ |
| reg = <0x0 0x80000000 0x0 0x0>; |
| }; |
| |
| pmu { |
| compatible = "arm,armv8-pmuv3"; |
| interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| psci { |
| compatible = "arm,psci-1.0"; |
| method = "smc"; |
| }; |
| |
| reserved-memory { |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| hyp_mem: memory@80000000 { |
| reg = <0x0 0x80000000 0x0 0x600000>; |
| no-map; |
| }; |
| |
| xbl_aop_mem: memory@80700000 { |
| reg = <0x0 0x80700000 0x0 0x160000>; |
| no-map; |
| }; |
| |
| cmd_db: memory@80860000 { |
| compatible = "qcom,cmd-db"; |
| reg = <0x0 0x80860000 0x0 0x20000>; |
| no-map; |
| }; |
| |
| smem_mem: memory@80900000 { |
| reg = <0x0 0x80900000 0x0 0x200000>; |
| no-map; |
| }; |
| |
| removed_mem: memory@80b00000 { |
| reg = <0x0 0x80b00000 0x0 0x5300000>; |
| no-map; |
| }; |
| |
| camera_mem: memory@86200000 { |
| reg = <0x0 0x86200000 0x0 0x500000>; |
| no-map; |
| }; |
| |
| wlan_mem: memory@86700000 { |
| reg = <0x0 0x86700000 0x0 0x100000>; |
| no-map; |
| }; |
| |
| ipa_fw_mem: memory@86800000 { |
| reg = <0x0 0x86800000 0x0 0x10000>; |
| no-map; |
| }; |
| |
| ipa_gsi_mem: memory@86810000 { |
| reg = <0x0 0x86810000 0x0 0xa000>; |
| no-map; |
| }; |
| |
| gpu_mem: memory@8681a000 { |
| reg = <0x0 0x8681a000 0x0 0x2000>; |
| no-map; |
| }; |
| |
| npu_mem: memory@86900000 { |
| reg = <0x0 0x86900000 0x0 0x500000>; |
| no-map; |
| }; |
| |
| video_mem: memory@86e00000 { |
| reg = <0x0 0x86e00000 0x0 0x500000>; |
| no-map; |
| }; |
| |
| cvp_mem: memory@87300000 { |
| reg = <0x0 0x87300000 0x0 0x500000>; |
| no-map; |
| }; |
| |
| cdsp_mem: memory@87800000 { |
| reg = <0x0 0x87800000 0x0 0x1400000>; |
| no-map; |
| }; |
| |
| slpi_mem: memory@88c00000 { |
| reg = <0x0 0x88c00000 0x0 0x1500000>; |
| no-map; |
| }; |
| |
| adsp_mem: memory@8a100000 { |
| reg = <0x0 0x8a100000 0x0 0x1d00000>; |
| no-map; |
| }; |
| |
| spss_mem: memory@8be00000 { |
| reg = <0x0 0x8be00000 0x0 0x100000>; |
| no-map; |
| }; |
| |
| cdsp_secure_heap: memory@8bf00000 { |
| reg = <0x0 0x8bf00000 0x0 0x4600000>; |
| no-map; |
| }; |
| }; |
| |
| smem: qcom,smem { |
| compatible = "qcom,smem"; |
| memory-region = <&smem_mem>; |
| hwlocks = <&tcsr_mutex 3>; |
| }; |
| |
| smp2p-adsp { |
| compatible = "qcom,smp2p"; |
| qcom,smem = <443>, <429>; |
| interrupts-extended = <&ipcc IPCC_CLIENT_LPASS |
| IPCC_MPROC_SIGNAL_SMP2P |
| IRQ_TYPE_EDGE_RISING>; |
| mboxes = <&ipcc IPCC_CLIENT_LPASS |
| IPCC_MPROC_SIGNAL_SMP2P>; |
| |
| qcom,local-pid = <0>; |
| qcom,remote-pid = <2>; |
| |
| smp2p_adsp_out: master-kernel { |
| qcom,entry-name = "master-kernel"; |
| #qcom,smem-state-cells = <1>; |
| }; |
| |
| smp2p_adsp_in: slave-kernel { |
| qcom,entry-name = "slave-kernel"; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| smp2p-cdsp { |
| compatible = "qcom,smp2p"; |
| qcom,smem = <94>, <432>; |
| interrupts-extended = <&ipcc IPCC_CLIENT_CDSP |
| IPCC_MPROC_SIGNAL_SMP2P |
| IRQ_TYPE_EDGE_RISING>; |
| mboxes = <&ipcc IPCC_CLIENT_CDSP |
| IPCC_MPROC_SIGNAL_SMP2P>; |
| |
| qcom,local-pid = <0>; |
| qcom,remote-pid = <5>; |
| |
| smp2p_cdsp_out: master-kernel { |
| qcom,entry-name = "master-kernel"; |
| #qcom,smem-state-cells = <1>; |
| }; |
| |
| smp2p_cdsp_in: slave-kernel { |
| qcom,entry-name = "slave-kernel"; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| smp2p-slpi { |
| compatible = "qcom,smp2p"; |
| qcom,smem = <481>, <430>; |
| interrupts-extended = <&ipcc IPCC_CLIENT_SLPI |
| IPCC_MPROC_SIGNAL_SMP2P |
| IRQ_TYPE_EDGE_RISING>; |
| mboxes = <&ipcc IPCC_CLIENT_SLPI |
| IPCC_MPROC_SIGNAL_SMP2P>; |
| |
| qcom,local-pid = <0>; |
| qcom,remote-pid = <3>; |
| |
| smp2p_slpi_out: master-kernel { |
| qcom,entry-name = "master-kernel"; |
| #qcom,smem-state-cells = <1>; |
| }; |
| |
| smp2p_slpi_in: slave-kernel { |
| qcom,entry-name = "slave-kernel"; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| soc: soc@0 { |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges = <0 0 0 0 0x10 0>; |
| dma-ranges = <0 0 0 0 0x10 0>; |
| compatible = "simple-bus"; |
| |
| gcc: clock-controller@100000 { |
| compatible = "qcom,gcc-sm8250"; |
| reg = <0x0 0x00100000 0x0 0x1f0000>; |
| #clock-cells = <1>; |
| #reset-cells = <1>; |
| #power-domain-cells = <1>; |
| clock-names = "bi_tcxo", |
| "bi_tcxo_ao", |
| "sleep_clk"; |
| clocks = <&rpmhcc RPMH_CXO_CLK>, |
| <&rpmhcc RPMH_CXO_CLK_A>, |
| <&sleep_clk>; |
| }; |
| |
| ipcc: mailbox@408000 { |
| compatible = "qcom,sm8250-ipcc", "qcom,ipcc"; |
| reg = <0 0x00408000 0 0x1000>; |
| interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-controller; |
| #interrupt-cells = <3>; |
| #mbox-cells = <2>; |
| }; |
| |
| qup_opp_table: qup-opp-table { |
| compatible = "operating-points-v2"; |
| |
| opp-50000000 { |
| opp-hz = /bits/ 64 <50000000>; |
| required-opps = <&rpmhpd_opp_min_svs>; |
| }; |
| |
| opp-75000000 { |
| opp-hz = /bits/ 64 <75000000>; |
| required-opps = <&rpmhpd_opp_low_svs>; |
| }; |
| |
| opp-120000000 { |
| opp-hz = /bits/ 64 <120000000>; |
| required-opps = <&rpmhpd_opp_svs>; |
| }; |
| }; |
| |
| qupv3_id_2: geniqup@8c0000 { |
| compatible = "qcom,geni-se-qup"; |
| reg = <0x0 0x008c0000 0x0 0x6000>; |
| clock-names = "m-ahb", "s-ahb"; |
| clocks = <&gcc GCC_QUPV3_WRAP_2_M_AHB_CLK>, |
| <&gcc GCC_QUPV3_WRAP_2_S_AHB_CLK>; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| status = "disabled"; |
| |
| i2c14: i2c@880000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00880000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_i2c14_default>; |
| interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| spi14: spi@880000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00880000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_spi14_default>; |
| interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| power-domains = <&rpmhpd SM8250_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| status = "disabled"; |
| }; |
| |
| i2c15: i2c@884000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00884000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_i2c15_default>; |
| interrupts = <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| spi15: spi@884000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00884000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_spi15_default>; |
| interrupts = <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| power-domains = <&rpmhpd SM8250_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| status = "disabled"; |
| }; |
| |
| i2c16: i2c@888000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00888000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_i2c16_default>; |
| interrupts = <GIC_SPI 584 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| spi16: spi@888000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00888000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_spi16_default>; |
| interrupts = <GIC_SPI 584 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| power-domains = <&rpmhpd SM8250_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| status = "disabled"; |
| }; |
| |
| i2c17: i2c@88c000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x0088c000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_i2c17_default>; |
| interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| spi17: spi@88c000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x0088c000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_spi17_default>; |
| interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| power-domains = <&rpmhpd SM8250_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| status = "disabled"; |
| }; |
| |
| uart17: serial@88c000 { |
| compatible = "qcom,geni-uart"; |
| reg = <0 0x0088c000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_uart17_default>; |
| interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>; |
| power-domains = <&rpmhpd SM8250_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| status = "disabled"; |
| }; |
| |
| i2c18: i2c@890000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00890000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_i2c18_default>; |
| interrupts = <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| spi18: spi@890000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00890000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_spi18_default>; |
| interrupts = <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| power-domains = <&rpmhpd SM8250_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| status = "disabled"; |
| }; |
| |
| uart18: serial@890000 { |
| compatible = "qcom,geni-uart"; |
| reg = <0 0x00890000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_uart18_default>; |
| interrupts = <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>; |
| power-domains = <&rpmhpd SM8250_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| status = "disabled"; |
| }; |
| |
| i2c19: i2c@894000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00894000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_i2c19_default>; |
| interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| spi19: spi@894000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00894000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_spi19_default>; |
| interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| power-domains = <&rpmhpd SM8250_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| status = "disabled"; |
| }; |
| }; |
| |
| qupv3_id_0: geniqup@9c0000 { |
| compatible = "qcom,geni-se-qup"; |
| reg = <0x0 0x009c0000 0x0 0x6000>; |
| clock-names = "m-ahb", "s-ahb"; |
| clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>, |
| <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| status = "disabled"; |
| |
| i2c0: i2c@980000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00980000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_i2c0_default>; |
| interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| spi0: spi@980000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00980000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_spi0_default>; |
| interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| power-domains = <&rpmhpd SM8250_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| status = "disabled"; |
| }; |
| |
| i2c1: i2c@984000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00984000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_i2c1_default>; |
| interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| spi1: spi@984000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00984000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_spi1_default>; |
| interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| power-domains = <&rpmhpd SM8250_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| status = "disabled"; |
| }; |
| |
| i2c2: i2c@988000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00988000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_i2c2_default>; |
| interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| spi2: spi@988000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00988000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_spi2_default>; |
| interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| power-domains = <&rpmhpd SM8250_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| status = "disabled"; |
| }; |
| |
| uart2: serial@988000 { |
| compatible = "qcom,geni-debug-uart"; |
| reg = <0 0x00988000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_uart2_default>; |
| interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>; |
| power-domains = <&rpmhpd SM8250_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| status = "disabled"; |
| }; |
| |
| i2c3: i2c@98c000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x0098c000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_i2c3_default>; |
| interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| spi3: spi@98c000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x0098c000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_spi3_default>; |
| interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| power-domains = <&rpmhpd SM8250_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| status = "disabled"; |
| }; |
| |
| i2c4: i2c@990000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00990000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_i2c4_default>; |
| interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| spi4: spi@990000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00990000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_spi4_default>; |
| interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| power-domains = <&rpmhpd SM8250_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| status = "disabled"; |
| }; |
| |
| i2c5: i2c@994000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00994000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_i2c5_default>; |
| interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| spi5: spi@994000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00994000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_spi5_default>; |
| interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| power-domains = <&rpmhpd SM8250_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| status = "disabled"; |
| }; |
| |
| i2c6: i2c@998000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00998000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_i2c6_default>; |
| interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| spi6: spi@998000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00998000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_spi6_default>; |
| interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| power-domains = <&rpmhpd SM8250_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| status = "disabled"; |
| }; |
| |
| uart6: serial@998000 { |
| compatible = "qcom,geni-uart"; |
| reg = <0 0x00998000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_uart6_default>; |
| interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>; |
| power-domains = <&rpmhpd SM8250_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| status = "disabled"; |
| }; |
| |
| i2c7: i2c@99c000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x0099c000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_i2c7_default>; |
| interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| spi7: spi@99c000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x0099c000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_spi7_default>; |
| interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| power-domains = <&rpmhpd SM8250_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| status = "disabled"; |
| }; |
| }; |
| |
| qupv3_id_1: geniqup@ac0000 { |
| compatible = "qcom,geni-se-qup"; |
| reg = <0x0 0x00ac0000 0x0 0x6000>; |
| clock-names = "m-ahb", "s-ahb"; |
| clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>, |
| <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| status = "disabled"; |
| |
| i2c8: i2c@a80000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00a80000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_i2c8_default>; |
| interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| spi8: spi@a80000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00a80000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_spi8_default>; |
| interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| power-domains = <&rpmhpd SM8250_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| status = "disabled"; |
| }; |
| |
| i2c9: i2c@a84000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00a84000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_i2c9_default>; |
| interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| spi9: spi@a84000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00a84000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_spi9_default>; |
| interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| power-domains = <&rpmhpd SM8250_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| status = "disabled"; |
| }; |
| |
| i2c10: i2c@a88000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00a88000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_i2c10_default>; |
| interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| spi10: spi@a88000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00a88000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_spi10_default>; |
| interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| power-domains = <&rpmhpd SM8250_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| status = "disabled"; |
| }; |
| |
| i2c11: i2c@a8c000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00a8c000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_i2c11_default>; |
| interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| spi11: spi@a8c000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00a8c000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_spi11_default>; |
| interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| power-domains = <&rpmhpd SM8250_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| status = "disabled"; |
| }; |
| |
| i2c12: i2c@a90000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00a90000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_i2c12_default>; |
| interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| spi12: spi@a90000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00a90000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_spi12_default>; |
| interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| power-domains = <&rpmhpd SM8250_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| status = "disabled"; |
| }; |
| |
| uart12: serial@a90000 { |
| compatible = "qcom,geni-debug-uart"; |
| reg = <0x0 0x00a90000 0x0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_uart12_default>; |
| interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>; |
| power-domains = <&rpmhpd SM8250_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| status = "disabled"; |
| }; |
| |
| i2c13: i2c@a94000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0 0x00a94000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_i2c13_default>; |
| interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| spi13: spi@a94000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0 0x00a94000 0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_spi13_default>; |
| interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| power-domains = <&rpmhpd SM8250_CX>; |
| operating-points-v2 = <&qup_opp_table>; |
| status = "disabled"; |
| }; |
| }; |
| |
| config_noc: interconnect@1500000 { |
| compatible = "qcom,sm8250-config-noc"; |
| reg = <0 0x01500000 0 0xa580>; |
| #interconnect-cells = <1>; |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| }; |
| |
| system_noc: interconnect@1620000 { |
| compatible = "qcom,sm8250-system-noc"; |
| reg = <0 0x01620000 0 0x1c200>; |
| #interconnect-cells = <1>; |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| }; |
| |
| mc_virt: interconnect@163d000 { |
| compatible = "qcom,sm8250-mc-virt"; |
| reg = <0 0x0163d000 0 0x1000>; |
| #interconnect-cells = <1>; |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| }; |
| |
| aggre1_noc: interconnect@16e0000 { |
| compatible = "qcom,sm8250-aggre1-noc"; |
| reg = <0 0x016e0000 0 0x1f180>; |
| #interconnect-cells = <1>; |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| }; |
| |
| aggre2_noc: interconnect@1700000 { |
| compatible = "qcom,sm8250-aggre2-noc"; |
| reg = <0 0x01700000 0 0x33000>; |
| #interconnect-cells = <1>; |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| }; |
| |
| compute_noc: interconnect@1733000 { |
| compatible = "qcom,sm8250-compute-noc"; |
| reg = <0 0x01733000 0 0xa180>; |
| #interconnect-cells = <1>; |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| }; |
| |
| mmss_noc: interconnect@1740000 { |
| compatible = "qcom,sm8250-mmss-noc"; |
| reg = <0 0x01740000 0 0x1f080>; |
| #interconnect-cells = <1>; |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| }; |
| |
| ufs_mem_hc: ufshc@1d84000 { |
| compatible = "qcom,sm8250-ufshc", "qcom,ufshc", |
| "jedec,ufs-2.0"; |
| reg = <0 0x01d84000 0 0x3000>; |
| interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>; |
| phys = <&ufs_mem_phy_lanes>; |
| phy-names = "ufsphy"; |
| lanes-per-direction = <2>; |
| #reset-cells = <1>; |
| resets = <&gcc GCC_UFS_PHY_BCR>; |
| reset-names = "rst"; |
| |
| power-domains = <&gcc UFS_PHY_GDSC>; |
| |
| clock-names = |
| "core_clk", |
| "bus_aggr_clk", |
| "iface_clk", |
| "core_clk_unipro", |
| "ref_clk", |
| "tx_lane0_sync_clk", |
| "rx_lane0_sync_clk", |
| "rx_lane1_sync_clk"; |
| clocks = |
| <&gcc GCC_UFS_PHY_AXI_CLK>, |
| <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>, |
| <&gcc GCC_UFS_PHY_AHB_CLK>, |
| <&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>, |
| <&rpmhcc RPMH_CXO_CLK>, |
| <&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>, |
| <&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>, |
| <&gcc GCC_UFS_PHY_RX_SYMBOL_1_CLK>; |
| freq-table-hz = |
| <37500000 300000000>, |
| <0 0>, |
| <0 0>, |
| <37500000 300000000>, |
| <0 0>, |
| <0 0>, |
| <0 0>, |
| <0 0>; |
| |
| status = "disabled"; |
| }; |
| |
| ufs_mem_phy: phy@1d87000 { |
| compatible = "qcom,sm8250-qmp-ufs-phy"; |
| reg = <0 0x01d87000 0 0x1c0>; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| clock-names = "ref", |
| "ref_aux"; |
| clocks = <&rpmhcc RPMH_CXO_CLK>, |
| <&gcc GCC_UFS_PHY_PHY_AUX_CLK>; |
| |
| resets = <&ufs_mem_hc 0>; |
| reset-names = "ufsphy"; |
| status = "disabled"; |
| |
| ufs_mem_phy_lanes: lanes@1d87400 { |
| reg = <0 0x01d87400 0 0x108>, |
| <0 0x01d87600 0 0x1e0>, |
| <0 0x01d87c00 0 0x1dc>, |
| <0 0x01d87800 0 0x108>, |
| <0 0x01d87a00 0 0x1e0>; |
| #phy-cells = <0>; |
| }; |
| }; |
| |
| ipa_virt: interconnect@1e00000 { |
| compatible = "qcom,sm8250-ipa-virt"; |
| reg = <0 0x01e00000 0 0x1000>; |
| #interconnect-cells = <1>; |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| }; |
| |
| tcsr_mutex: hwlock@1f40000 { |
| compatible = "qcom,tcsr-mutex"; |
| reg = <0x0 0x01f40000 0x0 0x40000>; |
| #hwlock-cells = <1>; |
| }; |
| |
| gpu: gpu@3d00000 { |
| /* |
| * note: the amd,imageon compatible makes it possible |
| * to use the drm/msm driver without the display node, |
| * make sure to remove it when display node is added |
| */ |
| compatible = "qcom,adreno-650.2", |
| "qcom,adreno", |
| "amd,imageon"; |
| #stream-id-cells = <16>; |
| |
| reg = <0 0x03d00000 0 0x40000>; |
| reg-names = "kgsl_3d0_reg_memory"; |
| |
| interrupts = <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>; |
| |
| iommus = <&adreno_smmu 0 0x401>; |
| |
| operating-points-v2 = <&gpu_opp_table>; |
| |
| qcom,gmu = <&gmu>; |
| |
| zap-shader { |
| memory-region = <&gpu_mem>; |
| }; |
| |
| /* note: downstream checks gpu binning for 670 Mhz */ |
| gpu_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| |
| opp-670000000 { |
| opp-hz = /bits/ 64 <670000000>; |
| opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>; |
| }; |
| |
| opp-587000000 { |
| opp-hz = /bits/ 64 <587000000>; |
| opp-level = <RPMH_REGULATOR_LEVEL_NOM>; |
| }; |
| |
| opp-525000000 { |
| opp-hz = /bits/ 64 <525000000>; |
| opp-level = <RPMH_REGULATOR_LEVEL_SVS_L2>; |
| }; |
| |
| opp-490000000 { |
| opp-hz = /bits/ 64 <490000000>; |
| opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>; |
| }; |
| |
| opp-441600000 { |
| opp-hz = /bits/ 64 <441600000>; |
| opp-level = <RPMH_REGULATOR_LEVEL_SVS_L0>; |
| }; |
| |
| opp-400000000 { |
| opp-hz = /bits/ 64 <400000000>; |
| opp-level = <RPMH_REGULATOR_LEVEL_SVS>; |
| }; |
| |
| opp-305000000 { |
| opp-hz = /bits/ 64 <305000000>; |
| opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>; |
| }; |
| }; |
| }; |
| |
| gmu: gmu@3d6a000 { |
| compatible="qcom,adreno-gmu-650.2", "qcom,adreno-gmu"; |
| |
| reg = <0 0x03d6a000 0 0x30000>, |
| <0 0x3de0000 0 0x10000>, |
| <0 0xb290000 0 0x10000>, |
| <0 0xb490000 0 0x10000>; |
| reg-names = "gmu", "rscc", "gmu_pdc", "gmu_pdc_seq"; |
| |
| interrupts = <GIC_SPI 304 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "hfi", "gmu"; |
| |
| clocks = <&gpucc GPU_CC_AHB_CLK>, |
| <&gpucc GPU_CC_CX_GMU_CLK>, |
| <&gpucc GPU_CC_CXO_CLK>, |
| <&gcc GCC_DDRSS_GPU_AXI_CLK>, |
| <&gcc GCC_GPU_MEMNOC_GFX_CLK>; |
| clock-names = "ahb", "gmu", "cxo", "axi", "memnoc"; |
| |
| power-domains = <&gpucc GPU_CX_GDSC>, |
| <&gpucc GPU_GX_GDSC>; |
| power-domain-names = "cx", "gx"; |
| |
| iommus = <&adreno_smmu 5 0x400>; |
| |
| operating-points-v2 = <&gmu_opp_table>; |
| |
| gmu_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| |
| opp-200000000 { |
| opp-hz = /bits/ 64 <200000000>; |
| opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>; |
| }; |
| }; |
| }; |
| |
| gpucc: clock-controller@3d90000 { |
| compatible = "qcom,sm8250-gpucc"; |
| reg = <0 0x03d90000 0 0x9000>; |
| clocks = <&rpmhcc RPMH_CXO_CLK>, |
| <&gcc GCC_GPU_GPLL0_CLK_SRC>, |
| <&gcc GCC_GPU_GPLL0_DIV_CLK_SRC>; |
| clock-names = "bi_tcxo", |
| "gcc_gpu_gpll0_clk_src", |
| "gcc_gpu_gpll0_div_clk_src"; |
| #clock-cells = <1>; |
| #reset-cells = <1>; |
| #power-domain-cells = <1>; |
| }; |
| |
| adreno_smmu: iommu@3da0000 { |
| compatible = "qcom,sm8250-smmu-500", "arm,mmu-500"; |
| reg = <0 0x03da0000 0 0x10000>; |
| #iommu-cells = <2>; |
| #global-interrupts = <2>; |
| interrupts = <GIC_SPI 672 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 673 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 678 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 679 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 680 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 681 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 682 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 683 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 684 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 685 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gpucc GPU_CC_AHB_CLK>, |
| <&gcc GCC_GPU_MEMNOC_GFX_CLK>, |
| <&gcc GCC_GPU_SNOC_DVM_GFX_CLK>; |
| clock-names = "ahb", "bus", "iface"; |
| |
| power-domains = <&gpucc GPU_CX_GDSC>; |
| }; |
| |
| slpi: remoteproc@5c00000 { |
| compatible = "qcom,sm8250-slpi-pas"; |
| reg = <0 0x05c00000 0 0x4000>; |
| |
| interrupts-extended = <&pdc 9 IRQ_TYPE_LEVEL_HIGH>, |
| <&smp2p_slpi_in 0 IRQ_TYPE_EDGE_RISING>, |
| <&smp2p_slpi_in 1 IRQ_TYPE_EDGE_RISING>, |
| <&smp2p_slpi_in 2 IRQ_TYPE_EDGE_RISING>, |
| <&smp2p_slpi_in 3 IRQ_TYPE_EDGE_RISING>; |
| interrupt-names = "wdog", "fatal", "ready", |
| "handover", "stop-ack"; |
| |
| clocks = <&rpmhcc RPMH_CXO_CLK>; |
| clock-names = "xo"; |
| |
| power-domains = <&aoss_qmp AOSS_QMP_LS_SLPI>, |
| <&rpmhpd SM8250_LCX>, |
| <&rpmhpd SM8250_LMX>; |
| power-domain-names = "load_state", "lcx", "lmx"; |
| |
| memory-region = <&slpi_mem>; |
| |
| qcom,smem-states = <&smp2p_slpi_out 0>; |
| qcom,smem-state-names = "stop"; |
| |
| status = "disabled"; |
| |
| glink-edge { |
| interrupts-extended = <&ipcc IPCC_CLIENT_SLPI |
| IPCC_MPROC_SIGNAL_GLINK_QMP |
| IRQ_TYPE_EDGE_RISING>; |
| mboxes = <&ipcc IPCC_CLIENT_SLPI |
| IPCC_MPROC_SIGNAL_GLINK_QMP>; |
| |
| label = "lpass"; |
| qcom,remote-pid = <3>; |
| }; |
| }; |
| |
| cdsp: remoteproc@8300000 { |
| compatible = "qcom,sm8250-cdsp-pas"; |
| reg = <0 0x08300000 0 0x10000>; |
| |
| interrupts-extended = <&intc GIC_SPI 578 IRQ_TYPE_LEVEL_HIGH>, |
| <&smp2p_cdsp_in 0 IRQ_TYPE_EDGE_RISING>, |
| <&smp2p_cdsp_in 1 IRQ_TYPE_EDGE_RISING>, |
| <&smp2p_cdsp_in 2 IRQ_TYPE_EDGE_RISING>, |
| <&smp2p_cdsp_in 3 IRQ_TYPE_EDGE_RISING>; |
| interrupt-names = "wdog", "fatal", "ready", |
| "handover", "stop-ack"; |
| |
| clocks = <&rpmhcc RPMH_CXO_CLK>; |
| clock-names = "xo"; |
| |
| power-domains = <&aoss_qmp AOSS_QMP_LS_CDSP>, |
| <&rpmhpd SM8250_CX>; |
| power-domain-names = "load_state", "cx"; |
| |
| memory-region = <&cdsp_mem>; |
| |
| qcom,smem-states = <&smp2p_cdsp_out 0>; |
| qcom,smem-state-names = "stop"; |
| |
| status = "disabled"; |
| |
| glink-edge { |
| interrupts-extended = <&ipcc IPCC_CLIENT_CDSP |
| IPCC_MPROC_SIGNAL_GLINK_QMP |
| IRQ_TYPE_EDGE_RISING>; |
| mboxes = <&ipcc IPCC_CLIENT_CDSP |
| IPCC_MPROC_SIGNAL_GLINK_QMP>; |
| |
| label = "lpass"; |
| qcom,remote-pid = <5>; |
| }; |
| }; |
| |
| dc_noc: interconnect@90c0000 { |
| compatible = "qcom,sm8250-dc-noc"; |
| reg = <0 0x090c0000 0 0x4200>; |
| #interconnect-cells = <1>; |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| }; |
| |
| gem_noc: interconnect@9100000 { |
| compatible = "qcom,sm8250-gem-noc"; |
| reg = <0 0x09100000 0 0xb4000>; |
| #interconnect-cells = <1>; |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| }; |
| |
| npu_noc: interconnect@9990000 { |
| compatible = "qcom,sm8250-npu-noc"; |
| reg = <0 0x09990000 0 0x1600>; |
| #interconnect-cells = <1>; |
| qcom,bcm-voters = <&apps_bcm_voter>; |
| }; |
| |
| pdc: interrupt-controller@b220000 { |
| compatible = "qcom,sm8250-pdc", "qcom,pdc"; |
| reg = <0 0x0b220000 0 0x30000>, <0 0x17c000f0 0 0x60>; |
| qcom,pdc-ranges = <0 480 94>, <94 609 31>, |
| <125 63 1>, <126 716 12>; |
| #interrupt-cells = <2>; |
| interrupt-parent = <&intc>; |
| interrupt-controller; |
| }; |
| |
| tsens0: thermal-sensor@c263000 { |
| compatible = "qcom,sm8250-tsens", "qcom,tsens-v2"; |
| reg = <0 0x0c263000 0 0x1ff>, /* TM */ |
| <0 0x0c222000 0 0x1ff>; /* SROT */ |
| #qcom,sensors = <16>; |
| interrupts = <GIC_SPI 506 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 508 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "uplow", "critical"; |
| #thermal-sensor-cells = <1>; |
| }; |
| |
| tsens1: thermal-sensor@c265000 { |
| compatible = "qcom,sm8250-tsens", "qcom,tsens-v2"; |
| reg = <0 0x0c265000 0 0x1ff>, /* TM */ |
| <0 0x0c223000 0 0x1ff>; /* SROT */ |
| #qcom,sensors = <9>; |
| interrupts = <GIC_SPI 507 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 509 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "uplow", "critical"; |
| #thermal-sensor-cells = <1>; |
| }; |
| |
| aoss_qmp: qmp@c300000 { |
| compatible = "qcom,sm8250-aoss-qmp"; |
| reg = <0 0x0c300000 0 0x100000>; |
| interrupts-extended = <&ipcc IPCC_CLIENT_AOP |
| IPCC_MPROC_SIGNAL_GLINK_QMP |
| IRQ_TYPE_EDGE_RISING>; |
| mboxes = <&ipcc IPCC_CLIENT_AOP |
| IPCC_MPROC_SIGNAL_GLINK_QMP>; |
| |
| #clock-cells = <0>; |
| #power-domain-cells = <1>; |
| }; |
| |
| spmi_bus: spmi@c440000 { |
| compatible = "qcom,spmi-pmic-arb"; |
| reg = <0x0 0x0c440000 0x0 0x0001100>, |
| <0x0 0x0c600000 0x0 0x2000000>, |
| <0x0 0x0e600000 0x0 0x0100000>, |
| <0x0 0x0e700000 0x0 0x00a0000>, |
| <0x0 0x0c40a000 0x0 0x0026000>; |
| reg-names = "core", "chnls", "obsrvr", "intr", "cnfg"; |
| interrupt-names = "periph_irq"; |
| interrupts-extended = <&pdc 1 IRQ_TYPE_LEVEL_HIGH>; |
| qcom,ee = <0>; |
| qcom,channel = <0>; |
| #address-cells = <2>; |
| #size-cells = <0>; |
| interrupt-controller; |
| #interrupt-cells = <4>; |
| }; |
| |
| tlmm: pinctrl@f100000 { |
| compatible = "qcom,sm8250-pinctrl"; |
| reg = <0 0x0f100000 0 0x300000>, |
| <0 0x0f500000 0 0x300000>, |
| <0 0x0f900000 0 0x300000>; |
| reg-names = "west", "south", "north"; |
| interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| gpio-ranges = <&tlmm 0 0 180>; |
| wakeup-parent = <&pdc>; |
| |
| qup_i2c0_default: qup-i2c0-default { |
| mux { |
| pins = "gpio28", "gpio29"; |
| function = "qup0"; |
| }; |
| |
| config { |
| pins = "gpio28", "gpio29"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| |
| qup_i2c1_default: qup-i2c1-default { |
| pinmux { |
| pins = "gpio4", "gpio5"; |
| function = "qup1"; |
| }; |
| |
| config { |
| pins = "gpio4", "gpio5"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| |
| qup_i2c2_default: qup-i2c2-default { |
| mux { |
| pins = "gpio115", "gpio116"; |
| function = "qup2"; |
| }; |
| |
| config { |
| pins = "gpio115", "gpio116"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| |
| qup_i2c3_default: qup-i2c3-default { |
| mux { |
| pins = "gpio119", "gpio120"; |
| function = "qup3"; |
| }; |
| |
| config { |
| pins = "gpio119", "gpio120"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| |
| qup_i2c4_default: qup-i2c4-default { |
| mux { |
| pins = "gpio8", "gpio9"; |
| function = "qup4"; |
| }; |
| |
| config { |
| pins = "gpio8", "gpio9"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| |
| qup_i2c5_default: qup-i2c5-default { |
| mux { |
| pins = "gpio12", "gpio13"; |
| function = "qup5"; |
| }; |
| |
| config { |
| pins = "gpio12", "gpio13"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| |
| qup_i2c6_default: qup-i2c6-default { |
| mux { |
| pins = "gpio16", "gpio17"; |
| function = "qup6"; |
| }; |
| |
| config { |
| pins = "gpio16", "gpio17"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| |
| qup_i2c7_default: qup-i2c7-default { |
| mux { |
| pins = "gpio20", "gpio21"; |
| function = "qup7"; |
| }; |
| |
| config { |
| pins = "gpio20", "gpio21"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| |
| qup_i2c8_default: qup-i2c8-default { |
| mux { |
| pins = "gpio24", "gpio25"; |
| function = "qup8"; |
| }; |
| |
| config { |
| pins = "gpio24", "gpio25"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| |
| qup_i2c9_default: qup-i2c9-default { |
| mux { |
| pins = "gpio125", "gpio126"; |
| function = "qup9"; |
| }; |
| |
| config { |
| pins = "gpio125", "gpio126"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| |
| qup_i2c10_default: qup-i2c10-default { |
| mux { |
| pins = "gpio129", "gpio130"; |
| function = "qup10"; |
| }; |
| |
| config { |
| pins = "gpio129", "gpio130"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| |
| qup_i2c11_default: qup-i2c11-default { |
| mux { |
| pins = "gpio60", "gpio61"; |
| function = "qup11"; |
| }; |
| |
| config { |
| pins = "gpio60", "gpio61"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| |
| qup_i2c12_default: qup-i2c12-default { |
| mux { |
| pins = "gpio32", "gpio33"; |
| function = "qup12"; |
| }; |
| |
| config { |
| pins = "gpio32", "gpio33"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| |
| qup_i2c13_default: qup-i2c13-default { |
| mux { |
| pins = "gpio36", "gpio37"; |
| function = "qup13"; |
| }; |
| |
| config { |
| pins = "gpio36", "gpio37"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| |
| qup_i2c14_default: qup-i2c14-default { |
| mux { |
| pins = "gpio40", "gpio41"; |
| function = "qup14"; |
| }; |
| |
| config { |
| pins = "gpio40", "gpio41"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| |
| qup_i2c15_default: qup-i2c15-default { |
| mux { |
| pins = "gpio44", "gpio45"; |
| function = "qup15"; |
| }; |
| |
| config { |
| pins = "gpio44", "gpio45"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| |
| qup_i2c16_default: qup-i2c16-default { |
| mux { |
| pins = "gpio48", "gpio49"; |
| function = "qup16"; |
| }; |
| |
| config { |
| pins = "gpio48", "gpio49"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| |
| qup_i2c17_default: qup-i2c17-default { |
| mux { |
| pins = "gpio52", "gpio53"; |
| function = "qup17"; |
| }; |
| |
| config { |
| pins = "gpio52", "gpio53"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| |
| qup_i2c18_default: qup-i2c18-default { |
| mux { |
| pins = "gpio56", "gpio57"; |
| function = "qup18"; |
| }; |
| |
| config { |
| pins = "gpio56", "gpio57"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| |
| qup_i2c19_default: qup-i2c19-default { |
| mux { |
| pins = "gpio0", "gpio1"; |
| function = "qup19"; |
| }; |
| |
| config { |
| pins = "gpio0", "gpio1"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| |
| qup_spi0_default: qup-spi0-default { |
| mux { |
| pins = "gpio28", "gpio29", |
| "gpio30", "gpio31"; |
| function = "qup0"; |
| }; |
| |
| config { |
| pins = "gpio28", "gpio29", |
| "gpio30", "gpio31"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| }; |
| |
| qup_spi1_default: qup-spi1-default { |
| mux { |
| pins = "gpio4", "gpio5", |
| "gpio6", "gpio7"; |
| function = "qup1"; |
| }; |
| |
| config { |
| pins = "gpio4", "gpio5", |
| "gpio6", "gpio7"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| }; |
| |
| qup_spi2_default: qup-spi2-default { |
| mux { |
| pins = "gpio115", "gpio116", |
| "gpio117", "gpio118"; |
| function = "qup2"; |
| }; |
| |
| config { |
| pins = "gpio115", "gpio116", |
| "gpio117", "gpio118"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| }; |
| |
| qup_spi3_default: qup-spi3-default { |
| mux { |
| pins = "gpio119", "gpio120", |
| "gpio121", "gpio122"; |
| function = "qup3"; |
| }; |
| |
| config { |
| pins = "gpio119", "gpio120", |
| "gpio121", "gpio122"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| }; |
| |
| qup_spi4_default: qup-spi4-default { |
| mux { |
| pins = "gpio8", "gpio9", |
| "gpio10", "gpio11"; |
| function = "qup4"; |
| }; |
| |
| config { |
| pins = "gpio8", "gpio9", |
| "gpio10", "gpio11"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| }; |
| |
| qup_spi5_default: qup-spi5-default { |
| mux { |
| pins = "gpio12", "gpio13", |
| "gpio14", "gpio15"; |
| function = "qup5"; |
| }; |
| |
| config { |
| pins = "gpio12", "gpio13", |
| "gpio14", "gpio15"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| }; |
| |
| qup_spi6_default: qup-spi6-default { |
| mux { |
| pins = "gpio16", "gpio17", |
| "gpio18", "gpio19"; |
| function = "qup6"; |
| }; |
| |
| config { |
| pins = "gpio16", "gpio17", |
| "gpio18", "gpio19"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| }; |
| |
| qup_spi7_default: qup-spi7-default { |
| mux { |
| pins = "gpio20", "gpio21", |
| "gpio22", "gpio23"; |
| function = "qup7"; |
| }; |
| |
| config { |
| pins = "gpio20", "gpio21", |
| "gpio22", "gpio23"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| }; |
| |
| qup_spi8_default: qup-spi8-default { |
| mux { |
| pins = "gpio24", "gpio25", |
| "gpio26", "gpio27"; |
| function = "qup8"; |
| }; |
| |
| config { |
| pins = "gpio24", "gpio25", |
| "gpio26", "gpio27"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| }; |
| |
| qup_spi9_default: qup-spi9-default { |
| mux { |
| pins = "gpio125", "gpio126", |
| "gpio127", "gpio128"; |
| function = "qup9"; |
| }; |
| |
| config { |
| pins = "gpio125", "gpio126", |
| "gpio127", "gpio128"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| }; |
| |
| qup_spi10_default: qup-spi10-default { |
| mux { |
| pins = "gpio129", "gpio130", |
| "gpio131", "gpio132"; |
| function = "qup10"; |
| }; |
| |
| config { |
| pins = "gpio129", "gpio130", |
| "gpio131", "gpio132"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| }; |
| |
| qup_spi11_default: qup-spi11-default { |
| mux { |
| pins = "gpio60", "gpio61", |
| "gpio62", "gpio63"; |
| function = "qup11"; |
| }; |
| |
| config { |
| pins = "gpio60", "gpio61", |
| "gpio62", "gpio63"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| }; |
| |
| qup_spi12_default: qup-spi12-default { |
| mux { |
| pins = "gpio32", "gpio33", |
| "gpio34", "gpio35"; |
| function = "qup12"; |
| }; |
| |
| config { |
| pins = "gpio32", "gpio33", |
| "gpio34", "gpio35"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| }; |
| |
| qup_spi13_default: qup-spi13-default { |
| mux { |
| pins = "gpio36", "gpio37", |
| "gpio38", "gpio39"; |
| function = "qup13"; |
| }; |
| |
| config { |
| pins = "gpio36", "gpio37", |
| "gpio38", "gpio39"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| }; |
| |
| qup_spi14_default: qup-spi14-default { |
| mux { |
| pins = "gpio40", "gpio41", |
| "gpio42", "gpio43"; |
| function = "qup14"; |
| }; |
| |
| config { |
| pins = "gpio40", "gpio41", |
| "gpio42", "gpio43"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| }; |
| |
| qup_spi15_default: qup-spi15-default { |
| mux { |
| pins = "gpio44", "gpio45", |
| "gpio46", "gpio47"; |
| function = "qup15"; |
| }; |
| |
| config { |
| pins = "gpio44", "gpio45", |
| "gpio46", "gpio47"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| }; |
| |
| qup_spi16_default: qup-spi16-default { |
| mux { |
| pins = "gpio48", "gpio49", |
| "gpio50", "gpio51"; |
| function = "qup16"; |
| }; |
| |
| config { |
| pins = "gpio48", "gpio49", |
| "gpio50", "gpio51"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| }; |
| |
| qup_spi17_default: qup-spi17-default { |
| mux { |
| pins = "gpio52", "gpio53", |
| "gpio54", "gpio55"; |
| function = "qup17"; |
| }; |
| |
| config { |
| pins = "gpio52", "gpio53", |
| "gpio54", "gpio55"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| }; |
| |
| qup_spi18_default: qup-spi18-default { |
| mux { |
| pins = "gpio56", "gpio57", |
| "gpio58", "gpio59"; |
| function = "qup18"; |
| }; |
| |
| config { |
| pins = "gpio56", "gpio57", |
| "gpio58", "gpio59"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| }; |
| |
| qup_spi19_default: qup-spi19-default { |
| mux { |
| pins = "gpio0", "gpio1", |
| "gpio2", "gpio3"; |
| function = "qup19"; |
| }; |
| |
| config { |
| pins = "gpio0", "gpio1", |
| "gpio2", "gpio3"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| }; |
| |
| qup_uart2_default: qup-uart2-default { |
| mux { |
| pins = "gpio117", "gpio118"; |
| function = "qup2"; |
| }; |
| }; |
| |
| qup_uart6_default: qup-uart6-default { |
| mux { |
| pins = "gpio16", "gpio17", |
| "gpio18", "gpio19"; |
| function = "qup6"; |
| }; |
| }; |
| |
| qup_uart12_default: qup-uart12-default { |
| mux { |
| pins = "gpio34", "gpio35"; |
| function = "qup12"; |
| }; |
| }; |
| |
| qup_uart17_default: qup-uart17-default { |
| mux { |
| pins = "gpio52", "gpio53", |
| "gpio54", "gpio55"; |
| function = "qup17"; |
| }; |
| }; |
| |
| qup_uart18_default: qup-uart18-default { |
| mux { |
| pins = "gpio58", "gpio59"; |
| function = "qup18"; |
| }; |
| }; |
| }; |
| |
| adsp: remoteproc@17300000 { |
| compatible = "qcom,sm8250-adsp-pas"; |
| reg = <0 0x17300000 0 0x100>; |
| |
| interrupts-extended = <&pdc 6 IRQ_TYPE_LEVEL_HIGH>, |
| <&smp2p_adsp_in 0 IRQ_TYPE_EDGE_RISING>, |
| <&smp2p_adsp_in 1 IRQ_TYPE_EDGE_RISING>, |
| <&smp2p_adsp_in 2 IRQ_TYPE_EDGE_RISING>, |
| <&smp2p_adsp_in 3 IRQ_TYPE_EDGE_RISING>; |
| interrupt-names = "wdog", "fatal", "ready", |
| "handover", "stop-ack"; |
| |
| clocks = <&rpmhcc RPMH_CXO_CLK>; |
| clock-names = "xo"; |
| |
| power-domains = <&aoss_qmp AOSS_QMP_LS_LPASS>, |
| <&rpmhpd SM8250_LCX>, |
| <&rpmhpd SM8250_LMX>; |
| power-domain-names = "load_state", "lcx", "lmx"; |
| |
| memory-region = <&adsp_mem>; |
| |
| qcom,smem-states = <&smp2p_adsp_out 0>; |
| qcom,smem-state-names = "stop"; |
| |
| status = "disabled"; |
| |
| glink-edge { |
| interrupts-extended = <&ipcc IPCC_CLIENT_LPASS |
| IPCC_MPROC_SIGNAL_GLINK_QMP |
| IRQ_TYPE_EDGE_RISING>; |
| mboxes = <&ipcc IPCC_CLIENT_LPASS |
| IPCC_MPROC_SIGNAL_GLINK_QMP>; |
| |
| label = "lpass"; |
| qcom,remote-pid = <2>; |
| }; |
| }; |
| |
| intc: interrupt-controller@17a00000 { |
| compatible = "arm,gic-v3"; |
| #interrupt-cells = <3>; |
| interrupt-controller; |
| reg = <0x0 0x17a00000 0x0 0x10000>, /* GICD */ |
| <0x0 0x17a60000 0x0 0x100000>; /* GICR * 8 */ |
| interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| watchdog@17c10000 { |
| compatible = "qcom,apss-wdt-sm8250", "qcom,kpss-wdt"; |
| reg = <0 0x17c10000 0 0x1000>; |
| clocks = <&sleep_clk>; |
| }; |
| |
| timer@17c20000 { |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| compatible = "arm,armv7-timer-mem"; |
| reg = <0x0 0x17c20000 0x0 0x1000>; |
| clock-frequency = <19200000>; |
| |
| frame@17c21000 { |
| frame-number = <0>; |
| interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0 0x17c21000 0x0 0x1000>, |
| <0x0 0x17c22000 0x0 0x1000>; |
| }; |
| |
| frame@17c23000 { |
| frame-number = <1>; |
| interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0 0x17c23000 0x0 0x1000>; |
| status = "disabled"; |
| }; |
| |
| frame@17c25000 { |
| frame-number = <2>; |
| interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0 0x17c25000 0x0 0x1000>; |
| status = "disabled"; |
| }; |
| |
| frame@17c27000 { |
| frame-number = <3>; |
| interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0 0x17c27000 0x0 0x1000>; |
| status = "disabled"; |
| }; |
| |
| frame@17c29000 { |
| frame-number = <4>; |
| interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0 0x17c29000 0x0 0x1000>; |
| status = "disabled"; |
| }; |
| |
| frame@17c2b000 { |
| frame-number = <5>; |
| interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0 0x17c2b000 0x0 0x1000>; |
| status = "disabled"; |
| }; |
| |
| frame@17c2d000 { |
| frame-number = <6>; |
| interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0 0x17c2d000 0x0 0x1000>; |
| status = "disabled"; |
| }; |
| }; |
| |
| apps_rsc: rsc@18200000 { |
| label = "apps_rsc"; |
| compatible = "qcom,rpmh-rsc"; |
| reg = <0x0 0x18200000 0x0 0x10000>, |
| <0x0 0x18210000 0x0 0x10000>, |
| <0x0 0x18220000 0x0 0x10000>; |
| reg-names = "drv-0", "drv-1", "drv-2"; |
| interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; |
| qcom,tcs-offset = <0xd00>; |
| qcom,drv-id = <2>; |
| qcom,tcs-config = <ACTIVE_TCS 2>, <SLEEP_TCS 3>, |
| <WAKE_TCS 3>, <CONTROL_TCS 1>; |
| |
| rpmhcc: clock-controller { |
| compatible = "qcom,sm8250-rpmh-clk"; |
| #clock-cells = <1>; |
| clock-names = "xo"; |
| clocks = <&xo_board>; |
| }; |
| |
| rpmhpd: power-controller { |
| compatible = "qcom,sm8250-rpmhpd"; |
| #power-domain-cells = <1>; |
| operating-points-v2 = <&rpmhpd_opp_table>; |
| |
| rpmhpd_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| |
| rpmhpd_opp_ret: opp1 { |
| opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>; |
| }; |
| |
| rpmhpd_opp_min_svs: opp2 { |
| opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>; |
| }; |
| |
| rpmhpd_opp_low_svs: opp3 { |
| opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>; |
| }; |
| |
| rpmhpd_opp_svs: opp4 { |
| opp-level = <RPMH_REGULATOR_LEVEL_SVS>; |
| }; |
| |
| rpmhpd_opp_svs_l1: opp5 { |
| opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>; |
| }; |
| |
| rpmhpd_opp_nom: opp6 { |
| opp-level = <RPMH_REGULATOR_LEVEL_NOM>; |
| }; |
| |
| rpmhpd_opp_nom_l1: opp7 { |
| opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>; |
| }; |
| |
| rpmhpd_opp_nom_l2: opp8 { |
| opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>; |
| }; |
| |
| rpmhpd_opp_turbo: opp9 { |
| opp-level = <RPMH_REGULATOR_LEVEL_TURBO>; |
| }; |
| |
| rpmhpd_opp_turbo_l1: opp10 { |
| opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>; |
| }; |
| }; |
| }; |
| |
| apps_bcm_voter: bcm_voter { |
| compatible = "qcom,bcm-voter"; |
| }; |
| }; |
| |
| epss_l3: interconnect@18591000 { |
| compatible = "qcom,sm8250-epss-l3"; |
| reg = <0 0x18590000 0 0x1000>; |
| |
| clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GPLL0>; |
| clock-names = "xo", "alternate"; |
| |
| #interconnect-cells = <1>; |
| }; |
| |
| cpufreq_hw: cpufreq@18591000 { |
| compatible = "qcom,sm8250-cpufreq-epss", "qcom,cpufreq-epss"; |
| reg = <0 0x18591000 0 0x1000>, |
| <0 0x18592000 0 0x1000>, |
| <0 0x18593000 0 0x1000>; |
| reg-names = "freq-domain0", "freq-domain1", |
| "freq-domain2"; |
| |
| clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GPLL0>; |
| clock-names = "xo", "alternate"; |
| |
| #freq-domain-cells = <1>; |
| }; |
| }; |
| |
| timer { |
| compatible = "arm,armv8-timer"; |
| interrupts = <GIC_PPI 13 |
| (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 14 |
| (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 11 |
| (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 12 |
| (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>; |
| }; |
| |
| thermal-zones { |
| cpu0-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens0 1>; |
| |
| trips { |
| cpu0_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu0_alert1: trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu0_crit: cpu_crit { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| |
| cooling-maps { |
| map0 { |
| trip = <&cpu0_alert0>; |
| cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| map1 { |
| trip = <&cpu0_alert1>; |
| cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| }; |
| }; |
| |
| cpu1-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens0 2>; |
| |
| trips { |
| cpu1_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu1_alert1: trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu1_crit: cpu_crit { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| |
| cooling-maps { |
| map0 { |
| trip = <&cpu1_alert0>; |
| cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| map1 { |
| trip = <&cpu1_alert1>; |
| cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| }; |
| }; |
| |
| cpu2-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens0 3>; |
| |
| trips { |
| cpu2_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu2_alert1: trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu2_crit: cpu_crit { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| |
| cooling-maps { |
| map0 { |
| trip = <&cpu2_alert0>; |
| cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| map1 { |
| trip = <&cpu2_alert1>; |
| cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| }; |
| }; |
| |
| cpu3-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens0 4>; |
| |
| trips { |
| cpu3_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu3_alert1: trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu3_crit: cpu_crit { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| |
| cooling-maps { |
| map0 { |
| trip = <&cpu3_alert0>; |
| cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| map1 { |
| trip = <&cpu3_alert1>; |
| cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| }; |
| }; |
| |
| cpu4-top-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens0 7>; |
| |
| trips { |
| cpu4_top_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu4_top_alert1: trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu4_top_crit: cpu_crit { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| |
| cooling-maps { |
| map0 { |
| trip = <&cpu4_top_alert0>; |
| cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| map1 { |
| trip = <&cpu4_top_alert1>; |
| cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| }; |
| }; |
| |
| cpu5-top-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens0 8>; |
| |
| trips { |
| cpu5_top_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu5_top_alert1: trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu5_top_crit: cpu_crit { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| |
| cooling-maps { |
| map0 { |
| trip = <&cpu5_top_alert0>; |
| cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| map1 { |
| trip = <&cpu5_top_alert1>; |
| cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| }; |
| }; |
| |
| cpu6-top-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens0 9>; |
| |
| trips { |
| cpu6_top_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu6_top_alert1: trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu6_top_crit: cpu_crit { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| |
| cooling-maps { |
| map0 { |
| trip = <&cpu6_top_alert0>; |
| cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| map1 { |
| trip = <&cpu6_top_alert1>; |
| cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| }; |
| }; |
| |
| cpu7-top-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens0 10>; |
| |
| trips { |
| cpu7_top_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu7_top_alert1: trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu7_top_crit: cpu_crit { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| |
| cooling-maps { |
| map0 { |
| trip = <&cpu7_top_alert0>; |
| cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| map1 { |
| trip = <&cpu7_top_alert1>; |
| cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| }; |
| }; |
| |
| cpu4-bottom-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens0 11>; |
| |
| trips { |
| cpu4_bottom_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu4_bottom_alert1: trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu4_bottom_crit: cpu_crit { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| |
| cooling-maps { |
| map0 { |
| trip = <&cpu4_bottom_alert0>; |
| cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| map1 { |
| trip = <&cpu4_bottom_alert1>; |
| cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| }; |
| }; |
| |
| cpu5-bottom-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens0 12>; |
| |
| trips { |
| cpu5_bottom_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu5_bottom_alert1: trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu5_bottom_crit: cpu_crit { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| |
| cooling-maps { |
| map0 { |
| trip = <&cpu5_bottom_alert0>; |
| cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| map1 { |
| trip = <&cpu5_bottom_alert1>; |
| cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| }; |
| }; |
| |
| cpu6-bottom-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens0 13>; |
| |
| trips { |
| cpu6_bottom_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu6_bottom_alert1: trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu6_bottom_crit: cpu_crit { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| |
| cooling-maps { |
| map0 { |
| trip = <&cpu6_bottom_alert0>; |
| cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| map1 { |
| trip = <&cpu6_bottom_alert1>; |
| cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| }; |
| }; |
| |
| cpu7-bottom-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens0 14>; |
| |
| trips { |
| cpu7_bottom_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu7_bottom_alert1: trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu7_bottom_crit: cpu_crit { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| |
| cooling-maps { |
| map0 { |
| trip = <&cpu7_bottom_alert0>; |
| cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| map1 { |
| trip = <&cpu7_bottom_alert1>; |
| cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| }; |
| }; |
| |
| aoss0-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens0 0>; |
| |
| trips { |
| aoss0_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| cluster0-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens0 5>; |
| |
| trips { |
| cluster0_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| cluster0_crit: cluster0_crit { |
| temperature = <110000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cluster1-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens0 6>; |
| |
| trips { |
| cluster1_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| cluster1_crit: cluster1_crit { |
| temperature = <110000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| gpu-thermal-top { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens0 15>; |
| |
| trips { |
| gpu1_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| aoss1-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens1 0>; |
| |
| trips { |
| aoss1_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| wlan-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens1 1>; |
| |
| trips { |
| wlan_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| video-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens1 2>; |
| |
| trips { |
| video_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| mem-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens1 3>; |
| |
| trips { |
| mem_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| q6-hvx-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens1 4>; |
| |
| trips { |
| q6_hvx_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| camera-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens1 5>; |
| |
| trips { |
| camera_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| compute-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens1 6>; |
| |
| trips { |
| compute_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| npu-thermal { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens1 7>; |
| |
| trips { |
| npu_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| gpu-thermal-bottom { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&tsens1 8>; |
| |
| trips { |
| gpu2_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| }; |
| }; |
