| # SPDX-License-Identifier: GPL-2.0-only | |
| # | |
| # PHY Layer Configuration | |
| # | |
| config PHYLINK | |
| tristate | |
| select PHYLIB | |
| select SWPHY | |
| help | |
| PHYlink models the link between the PHY and MAC, allowing fixed | |
| configuration links, PHYs, and Serdes links with MAC level | |
| autonegotiation modes. | |
| menuconfig PHYLIB | |
| tristate "PHY Device support and infrastructure" | |
| help | |
| Ethernet controllers are usually attached to PHY | |
| devices. This option provides infrastructure for | |
| managing PHY devices. | |
| if PHYLIB | |
| config SWPHY | |
| bool | |
| config PHY_PACKAGE | |
| tristate | |
| config LED_TRIGGER_PHY | |
| bool "Support LED triggers for tracking link state" | |
| depends on LEDS_TRIGGERS | |
| help | |
| Adds support for a set of LED trigger events per-PHY. Link | |
| state change will trigger the events, for consumption by an | |
| LED class driver. There are triggers for each link speed currently | |
| supported by the PHY and also a one common "link" trigger as a | |
| logical-or of all the link speed ones. | |
| All these triggers are named according to the following pattern: | |
| <mii bus id>:<phy>:<speed> | |
| Where speed is in the form: | |
| <Speed in megabits>Mbps OR <Speed in gigabits>Gbps OR link | |
| for any speed known to the PHY. | |
| config OPEN_ALLIANCE_HELPERS | |
| bool | |
| config PHYLIB_LEDS | |
| def_bool OF | |
| depends on LEDS_CLASS=y || LEDS_CLASS=PHYLIB | |
| help | |
| When LED class support is enabled, phylib can automatically | |
| probe LED setting from device tree. | |
| config FIXED_PHY | |
| tristate "MDIO Bus/PHY emulation with fixed speed/link PHYs" | |
| select SWPHY | |
| help | |
| Adds the platform "fixed" MDIO Bus to cover the boards that use | |
| PHYs that are not connected to the real MDIO bus. | |
| Currently tested with mpc866ads and mpc8349e-mitx. | |
| config RUST_PHYLIB_ABSTRACTIONS | |
| bool "Rust PHYLIB abstractions support" | |
| depends on RUST | |
| depends on PHYLIB=y | |
| help | |
| Adds support needed for PHY drivers written in Rust. It provides | |
| a wrapper around the C phylib core. | |
| config SFP | |
| tristate "SFP cage support" | |
| depends on I2C && PHYLINK | |
| depends on HWMON || HWMON=n | |
| select MDIO_I2C | |
| comment "MII PHY device drivers" | |
| config AS21XXX_PHY | |
| tristate "Aeonsemi AS21xxx PHYs" | |
| help | |
| Currently supports the Aeonsemi AS21xxx PHY. | |
| These are C45 PHYs 10G that require all a generic firmware. | |
| Supported PHYs AS21011JB1, AS21011PB1, AS21010JB1, AS21010PB1, | |
| AS21511JB1, AS21511PB1, AS21510JB1, AS21510PB1, AS21210JB1, | |
| AS21210PB1 that all register with the PHY ID 0x7500 0x7500 | |
| before the firmware is loaded. | |
| config AIR_AN8801_PHY | |
| tristate "Airoha AN8801 Gigabit PHY" | |
| select AIR_NET_PHYLIB | |
| help | |
| Currently supports the Airoha AN8801R PHY. | |
| config AIR_EN8811H_PHY | |
| tristate "Airoha EN8811H 2.5 Gigabit PHY" | |
| select AIR_NET_PHYLIB | |
| select PHY_COMMON_PROPS | |
| help | |
| Currently supports the Airoha EN8811H PHY. | |
| config AIR_NET_PHYLIB | |
| tristate | |
| help | |
| Airoha Ethernet PHY common library | |
| config AMD_PHY | |
| tristate "AMD and Altima PHYs" | |
| help | |
| Currently supports the AMD am79c874 and Altima AC101L. | |
| config MESON_GXL_PHY | |
| tristate "Amlogic Meson GXL Internal PHY" | |
| depends on ARCH_MESON || COMPILE_TEST | |
| select SMSC_PHY | |
| help | |
| Currently has a driver for the Amlogic Meson GXL Internal PHY | |
| config ADIN_PHY | |
| tristate "Analog Devices Industrial Ethernet PHYs" | |
| help | |
| Adds support for the Analog Devices Industrial Ethernet PHYs. | |
| Currently supports the: | |
| - ADIN1200 - Robust,Industrial, Low Power 10/100 Ethernet PHY | |
| - ADIN1300 - Robust,Industrial, Low Latency 10/100/1000 Gigabit | |
| Ethernet PHY | |
| config ADIN1100_PHY | |
| tristate "Analog Devices Industrial Ethernet T1L PHYs" | |
| help | |
| Adds support for the Analog Devices Industrial T1L Ethernet PHYs. | |
| Currently supports the: | |
| - ADIN1100 - Robust,Industrial, Low Power 10BASE-T1L Ethernet PHY | |
| config AMCC_QT2025_PHY | |
| tristate "AMCC QT2025 PHY" | |
| depends on RUST_PHYLIB_ABSTRACTIONS | |
| depends on RUST_FW_LOADER_ABSTRACTIONS | |
| help | |
| Adds support for the Applied Micro Circuits Corporation QT2025 PHY. | |
| source "drivers/net/phy/aquantia/Kconfig" | |
| config AX88796B_PHY | |
| tristate "Asix PHYs" | |
| help | |
| Currently supports the Asix Electronics PHY found in the X-Surf 100 | |
| AX88796B package. | |
| config AX88796B_RUST_PHY | |
| bool "Rust reference driver for Asix PHYs" | |
| depends on RUST_PHYLIB_ABSTRACTIONS && AX88796B_PHY | |
| help | |
| Uses the Rust reference driver for Asix PHYs (ax88796b_rust.ko). | |
| The features are equivalent. It supports the Asix Electronics PHY | |
| found in the X-Surf 100 AX88796B package. | |
| config BROADCOM_PHY | |
| tristate "Broadcom 54XX PHYs" | |
| select BCM_NET_PHYLIB | |
| select BCM_NET_PHYPTP if NETWORK_PHY_TIMESTAMPING | |
| depends on PTP_1588_CLOCK_OPTIONAL | |
| help | |
| Currently supports the BCM5411, BCM5421, BCM5461, BCM54616S, BCM5464, | |
| BCM5481, BCM54810 and BCM5482 PHYs. | |
| config BCM54140_PHY | |
| tristate "Broadcom BCM54140 PHY" | |
| depends on HWMON || HWMON=n | |
| select BCM_NET_PHYLIB | |
| select PHY_PACKAGE | |
| help | |
| Support the Broadcom BCM54140 Quad SGMII/QSGMII PHY. | |
| This driver also supports the hardware monitoring of this PHY and | |
| exposes voltage and temperature sensors. | |
| config BCM63XX_PHY | |
| tristate "Broadcom 63xx SOCs internal PHY" | |
| depends on BCM63XX || COMPILE_TEST | |
| select BCM_NET_PHYLIB | |
| help | |
| Currently supports the 6348 and 6358 PHYs. | |
| config BCM7XXX_PHY | |
| tristate "Broadcom 7xxx SOCs internal PHYs" | |
| select BCM_NET_PHYLIB | |
| help | |
| Currently supports the BCM7366, BCM7439, BCM7445, and | |
| 40nm and 65nm generation of BCM7xxx Set Top Box SoCs. | |
| config BCM84881_PHY | |
| tristate "Broadcom BCM84881 PHY" | |
| help | |
| Support the Broadcom BCM84881 PHY. | |
| config BCM87XX_PHY | |
| tristate "Broadcom BCM8706 and BCM8727 PHYs" | |
| help | |
| Currently supports the BCM8706 and BCM8727 10G Ethernet PHYs. | |
| config BCM_CYGNUS_PHY | |
| tristate "Broadcom Cygnus/Omega SoC internal PHY" | |
| depends on ARCH_BCM_IPROC || COMPILE_TEST | |
| depends on MDIO_BCM_IPROC | |
| select BCM_NET_PHYLIB | |
| help | |
| This PHY driver is for the 1G internal PHYs of the Broadcom | |
| Cygnus and Omega Family SoC. | |
| Currently supports internal PHY's used in the BCM11300, | |
| BCM11320, BCM11350, BCM11360, BCM58300, BCM58302, | |
| BCM58303 & BCM58305 Broadcom Cygnus SoCs. | |
| config BCM_NET_PHYLIB | |
| tristate | |
| config BCM_NET_PHYPTP | |
| tristate | |
| config CICADA_PHY | |
| tristate "Cicada PHYs" | |
| help | |
| Currently supports the cis8204 | |
| config CORTINA_PHY | |
| tristate "Cortina EDC CDR 10G Ethernet PHY" | |
| help | |
| Currently supports the CS4340 phy. | |
| config DAVICOM_PHY | |
| tristate "Davicom PHYs" | |
| help | |
| Currently supports dm9161e and dm9131 | |
| config ICPLUS_PHY | |
| tristate "ICPlus PHYs" | |
| help | |
| Currently supports the IP175C and IP1001 PHYs. | |
| config LXT_PHY | |
| tristate "Intel LXT PHYs" | |
| help | |
| Currently supports the lxt970, lxt971 | |
| config INTEL_XWAY_PHY | |
| tristate "Intel XWAY PHYs" | |
| help | |
| Supports the Intel XWAY (former Lantiq) 11G and 22F PHYs. | |
| These PHYs are marked as standalone chips under the names | |
| PEF 7061, PEF 7071 and PEF 7072 or integrated into the Intel | |
| SoCs xRX200, xRX300, xRX330, xRX350 and xRX550. | |
| config LSI_ET1011C_PHY | |
| tristate "LSI ET1011C PHY" | |
| help | |
| Supports the LSI ET1011C PHY. | |
| config MARVELL_PHY | |
| tristate "Marvell Alaska PHYs" | |
| help | |
| Currently has a driver for the 88E1XXX | |
| config MARVELL_10G_PHY | |
| tristate "Marvell Alaska 10Gbit PHYs" | |
| help | |
| Support for the Marvell Alaska MV88X3310 and compatible PHYs. | |
| config MARVELL_88Q2XXX_PHY | |
| tristate "Marvell 88Q2XXX PHY" | |
| depends on HWMON || HWMON=n | |
| help | |
| Support for the Marvell 88Q2XXX 100/1000BASE-T1 Automotive Ethernet | |
| PHYs. | |
| config MARVELL_88X2222_PHY | |
| tristate "Marvell 88X2222 PHY" | |
| help | |
| Support for the Marvell 88X2222 Dual-port Multi-speed Ethernet | |
| Transceiver. | |
| config MAXLINEAR_GPHY | |
| tristate "Maxlinear Ethernet PHYs" | |
| select POLYNOMIAL if HWMON | |
| depends on HWMON || HWMON=n | |
| help | |
| Support for the Maxlinear GPY115, GPY211, GPY212, GPY215, | |
| GPY241, GPY245 PHYs. | |
| config MAXLINEAR_86110_PHY | |
| tristate "MaxLinear MXL86110 PHY support" | |
| help | |
| Support for the MaxLinear MXL86110 Gigabit Ethernet | |
| Physical Layer transceiver. | |
| The MXL86110 is commonly used in networking equipment such as | |
| routers, switches, and embedded systems, providing the | |
| physical interface for 10/100/1000 Mbps Ethernet connections | |
| over copper media. | |
| If you are using a board with the MXL86110 PHY connected to your | |
| Ethernet MAC, you should enable this option. | |
| source "drivers/net/phy/mediatek/Kconfig" | |
| config MICREL_PHY | |
| tristate "Micrel PHYs" | |
| depends on PTP_1588_CLOCK_OPTIONAL | |
| select PHY_PACKAGE | |
| help | |
| Supports the KSZ8xxx, KSZ9xxx, and LAN88xx families of Micrel/Microchip PHYs. | |
| config MICROCHIP_T1S_PHY | |
| tristate "Microchip 10BASE-T1S Ethernet PHYs" | |
| help | |
| Currently supports the LAN8670/1/2 Rev.B1/C1/C2/D0 and | |
| LAN8650/1 Rev.B0/B1 Internal PHYs. | |
| config MICROCHIP_PHY | |
| tristate "Microchip PHYs" | |
| help | |
| Supports the LAN88XX PHYs. | |
| config MICROCHIP_T1_PHY | |
| tristate "Microchip T1 PHYs" | |
| select MICROCHIP_PHY_RDS_PTP if NETWORK_PHY_TIMESTAMPING | |
| depends on PTP_1588_CLOCK_OPTIONAL | |
| help | |
| Supports the LAN8XXX PHYs. | |
| config MICROCHIP_PHY_RDS_PTP | |
| tristate | |
| help | |
| Currently supports LAN887X T1 PHY | |
| config MICROSEMI_PHY | |
| tristate "Microsemi PHYs" | |
| depends on MACSEC || MACSEC=n | |
| depends on PTP_1588_CLOCK_OPTIONAL || !NETWORK_PHY_TIMESTAMPING | |
| select CRYPTO_LIB_AES if MACSEC | |
| select PHY_PACKAGE | |
| help | |
| Currently supports VSC8514, VSC8530, VSC8531, VSC8540 and VSC8541 PHYs | |
| config MOTORCOMM_PHY | |
| tristate "Motorcomm PHYs" | |
| help | |
| Enables support for Motorcomm network PHYs. | |
| Currently supports YT85xx Gigabit Ethernet PHYs. | |
| config NATIONAL_PHY | |
| tristate "National Semiconductor PHYs" | |
| help | |
| Currently supports the DP83865 PHY. | |
| config NXP_CBTX_PHY | |
| tristate "NXP 100BASE-TX PHYs" | |
| help | |
| Support the 100BASE-TX PHY integrated on the SJA1110 automotive | |
| switch family. | |
| config NXP_C45_TJA11XX_PHY | |
| tristate "NXP C45 TJA11XX PHYs" | |
| depends on PTP_1588_CLOCK_OPTIONAL | |
| depends on MACSEC || !MACSEC | |
| help | |
| Enable support for NXP C45 TJA11XX PHYs. | |
| Currently supports the TJA1103, TJA1104, TJA1120 and TJA1121 PHYs. | |
| config NXP_TJA11XX_PHY | |
| tristate "NXP TJA11xx PHYs support" | |
| depends on HWMON | |
| help | |
| Currently supports the NXP TJA1100, TJA1101 and TJA1102 PHYs. | |
| config NCN26000_PHY | |
| tristate "Onsemi 10BASE-T1S Ethernet PHY" | |
| help | |
| Adds support for the onsemi 10BASE-T1S Ethernet PHY. | |
| Currently supports the NCN26000 10BASE-T1S Industrial PHY | |
| with MII interface. | |
| source "drivers/net/phy/qcom/Kconfig" | |
| config QSEMI_PHY | |
| tristate "Quality Semiconductor PHYs" | |
| help | |
| Currently supports the qs6612 | |
| source "drivers/net/phy/realtek/Kconfig" | |
| config RENESAS_PHY | |
| tristate "Renesas PHYs" | |
| help | |
| Supports the Renesas PHYs uPD60620 and uPD60620A. | |
| config ROCKCHIP_PHY | |
| tristate "Rockchip Ethernet PHYs" | |
| help | |
| Currently supports the integrated Ethernet PHY. | |
| config SMSC_PHY | |
| tristate "SMSC PHYs" | |
| select CRC16 | |
| help | |
| Currently supports the LAN83C185, LAN8187 and LAN8700 PHYs | |
| config STE10XP | |
| tristate "STMicroelectronics STe10Xp PHYs" | |
| help | |
| This is the driver for the STe100p and STe101p PHYs. | |
| config TERANETICS_PHY | |
| tristate "Teranetics PHYs" | |
| help | |
| Currently supports the Teranetics TN2020 | |
| config DP83822_PHY | |
| tristate "Texas Instruments DP83822/825/826 PHYs" | |
| help | |
| Supports the DP83822, DP83825I, DP83825CM, DP83825CS, DP83825S, | |
| DP83826C and DP83826NC PHYs. | |
| config DP83TC811_PHY | |
| tristate "Texas Instruments DP83TC811 PHY" | |
| help | |
| Supports the DP83TC811 PHY. | |
| config DP83848_PHY | |
| tristate "Texas Instruments DP83848 PHY" | |
| help | |
| Supports the DP83848 PHY. | |
| config DP83867_PHY | |
| tristate "Texas Instruments DP83867 Gigabit PHY" | |
| help | |
| Currently supports the DP83867 PHY. | |
| config DP83869_PHY | |
| tristate "Texas Instruments DP83869 Gigabit PHY" | |
| help | |
| Currently supports the DP83869 PHY. This PHY supports copper and | |
| fiber connections. | |
| config DP83TD510_PHY | |
| tristate "Texas Instruments DP83TD510 Ethernet 10Base-T1L PHY" | |
| help | |
| Support for the DP83TD510 Ethernet 10Base-T1L PHY. This PHY supports | |
| a 10M single pair Ethernet connection for up to 1000 meter cable. | |
| config DP83TG720_PHY | |
| tristate "Texas Instruments DP83TG720 Ethernet 1000Base-T1 PHY" | |
| select OPEN_ALLIANCE_HELPERS | |
| help | |
| The DP83TG720S-Q1 is an automotive Ethernet physical layer | |
| transceiver compliant with IEEE 802.3bp and Open Alliance | |
| standards. It supports key functions necessary for | |
| transmitting and receiving data over both unshielded and | |
| shielded single twisted-pair cables. This device offers | |
| flexible xMII interface options, including support for both | |
| RGMII and SGMII MAC interfaces. It's suitable for applications | |
| requiring high-speed data transmission in automotive | |
| networking environments. | |
| config VITESSE_PHY | |
| tristate "Vitesse PHYs" | |
| help | |
| Currently supports the vsc8244 | |
| config XILINX_GMII2RGMII | |
| tristate "Xilinx GMII2RGMII converter driver" | |
| help | |
| This driver support xilinx GMII to RGMII IP core it provides | |
| the Reduced Gigabit Media Independent Interface(RGMII) between | |
| Ethernet physical media devices and the Gigabit Ethernet controller. | |
| endif # PHYLIB |