| // SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| |
| /dts-v1/; |
| |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/leds/common.h> |
| #include "rk3588.dtsi" |
| |
| / { |
| model = "Radxa ROCK 5B"; |
| compatible = "radxa,rock-5b", "rockchip,rk3588"; |
| |
| aliases { |
| mmc0 = &sdhci; |
| mmc1 = &sdmmc; |
| mmc2 = &sdio; |
| }; |
| |
| chosen { |
| stdout-path = "serial2:1500000n8"; |
| }; |
| |
| analog-sound { |
| compatible = "audio-graph-card"; |
| label = "rk3588-es8316"; |
| |
| widgets = "Microphone", "Mic Jack", |
| "Headphone", "Headphones"; |
| |
| routing = "MIC2", "Mic Jack", |
| "Headphones", "HPOL", |
| "Headphones", "HPOR"; |
| |
| dais = <&i2s0_8ch_p0>; |
| hp-det-gpio = <&gpio1 RK_PD5 GPIO_ACTIVE_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&hp_detect>; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&led_rgb_b>; |
| |
| led_rgb_b { |
| function = LED_FUNCTION_STATUS; |
| color = <LED_COLOR_ID_BLUE>; |
| gpios = <&gpio0 RK_PB7 GPIO_ACTIVE_HIGH>; |
| linux,default-trigger = "heartbeat"; |
| }; |
| }; |
| |
| fan: pwm-fan { |
| compatible = "pwm-fan"; |
| cooling-levels = <0 120 150 180 210 240 255>; |
| fan-supply = <&vcc5v0_sys>; |
| pwms = <&pwm1 0 50000 0>; |
| #cooling-cells = <2>; |
| }; |
| |
| rfkill { |
| compatible = "rfkill-gpio"; |
| label = "rfkill-pcie-wlan"; |
| radio-type = "wlan"; |
| shutdown-gpios = <&gpio4 RK_PA2 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| rfkill-bt { |
| compatible = "rfkill-gpio"; |
| label = "rfkill-m2-bt"; |
| radio-type = "bluetooth"; |
| shutdown-gpios = <&gpio3 RK_PD5 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| vcc3v3_pcie2x1l0: vcc3v3-pcie2x1l0-regulator { |
| compatible = "regulator-fixed"; |
| enable-active-high; |
| gpios = <&gpio1 RK_PD2 GPIO_ACTIVE_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pcie2_0_vcc3v3_en>; |
| regulator-name = "vcc3v3_pcie2x1l0"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| startup-delay-us = <50000>; |
| vin-supply = <&vcc5v0_sys>; |
| }; |
| |
| vcc3v3_pcie2x1l2: vcc3v3-pcie2x1l2-regulator { |
| compatible = "regulator-fixed"; |
| regulator-name = "vcc3v3_pcie2x1l2"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| startup-delay-us = <5000>; |
| vin-supply = <&vcc_3v3_s3>; |
| }; |
| |
| vcc3v3_pcie30: vcc3v3-pcie30-regulator { |
| compatible = "regulator-fixed"; |
| enable-active-high; |
| gpios = <&gpio1 RK_PA4 GPIO_ACTIVE_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pcie3_vcc3v3_en>; |
| regulator-name = "vcc3v3_pcie30"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| startup-delay-us = <5000>; |
| vin-supply = <&vcc5v0_sys>; |
| }; |
| |
| vcc5v0_host: vcc5v0-host-regulator { |
| compatible = "regulator-fixed"; |
| regulator-name = "vcc5v0_host"; |
| regulator-boot-on; |
| regulator-always-on; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| enable-active-high; |
| gpio = <&gpio4 RK_PB0 GPIO_ACTIVE_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&vcc5v0_host_en>; |
| vin-supply = <&vcc5v0_sys>; |
| }; |
| |
| vcc5v0_sys: vcc5v0-sys-regulator { |
| compatible = "regulator-fixed"; |
| regulator-name = "vcc5v0_sys"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| }; |
| |
| vcc_1v1_nldo_s3: vcc-1v1-nldo-s3-regulator { |
| compatible = "regulator-fixed"; |
| regulator-name = "vcc_1v1_nldo_s3"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <1100000>; |
| regulator-max-microvolt = <1100000>; |
| vin-supply = <&vcc5v0_sys>; |
| }; |
| }; |
| |
| &combphy0_ps { |
| status = "okay"; |
| }; |
| |
| &combphy1_ps { |
| status = "okay"; |
| }; |
| |
| &combphy2_psu { |
| status = "okay"; |
| }; |
| |
| &cpu_b0 { |
| cpu-supply = <&vdd_cpu_big0_s0>; |
| }; |
| |
| &cpu_b1 { |
| cpu-supply = <&vdd_cpu_big0_s0>; |
| }; |
| |
| &cpu_b2 { |
| cpu-supply = <&vdd_cpu_big1_s0>; |
| }; |
| |
| &cpu_b3 { |
| cpu-supply = <&vdd_cpu_big1_s0>; |
| }; |
| |
| &cpu_l0 { |
| cpu-supply = <&vdd_cpu_lit_s0>; |
| }; |
| |
| &cpu_l1 { |
| cpu-supply = <&vdd_cpu_lit_s0>; |
| }; |
| |
| &cpu_l2 { |
| cpu-supply = <&vdd_cpu_lit_s0>; |
| }; |
| |
| &cpu_l3 { |
| cpu-supply = <&vdd_cpu_lit_s0>; |
| }; |
| |
| &gpu { |
| mali-supply = <&vdd_gpu_s0>; |
| status = "okay"; |
| }; |
| |
| &i2c0 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c0m2_xfer>; |
| status = "okay"; |
| |
| vdd_cpu_big0_s0: regulator@42 { |
| compatible = "rockchip,rk8602"; |
| reg = <0x42>; |
| fcs,suspend-voltage-selector = <1>; |
| regulator-name = "vdd_cpu_big0_s0"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <550000>; |
| regulator-max-microvolt = <1050000>; |
| regulator-ramp-delay = <2300>; |
| vin-supply = <&vcc5v0_sys>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| vdd_cpu_big1_s0: regulator@43 { |
| compatible = "rockchip,rk8603", "rockchip,rk8602"; |
| reg = <0x43>; |
| fcs,suspend-voltage-selector = <1>; |
| regulator-name = "vdd_cpu_big1_s0"; |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <550000>; |
| regulator-max-microvolt = <1050000>; |
| regulator-ramp-delay = <2300>; |
| vin-supply = <&vcc5v0_sys>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| }; |
| |
| &i2c6 { |
| status = "okay"; |
| |
| hym8563: rtc@51 { |
| compatible = "haoyu,hym8563"; |
| reg = <0x51>; |
| #clock-cells = <0>; |
| clock-output-names = "hym8563"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&hym8563_int>; |
| interrupt-parent = <&gpio0>; |
| interrupts = <RK_PB0 IRQ_TYPE_LEVEL_LOW>; |
| wakeup-source; |
| }; |
| }; |
| |
| &i2c7 { |
| status = "okay"; |
| |
| es8316: audio-codec@11 { |
| compatible = "everest,es8316"; |
| reg = <0x11>; |
| clocks = <&cru I2S0_8CH_MCLKOUT>; |
| clock-names = "mclk"; |
| assigned-clocks = <&cru I2S0_8CH_MCLKOUT>; |
| assigned-clock-rates = <12288000>; |
| #sound-dai-cells = <0>; |
| |
| port { |
| es8316_p0_0: endpoint { |
| remote-endpoint = <&i2s0_8ch_p0_0>; |
| }; |
| }; |
| }; |
| }; |
| |
| &i2s0_8ch { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2s0_lrck |
| &i2s0_mclk |
| &i2s0_sclk |
| &i2s0_sdi0 |
| &i2s0_sdo0>; |
| status = "okay"; |
| |
| i2s0_8ch_p0: port { |
| i2s0_8ch_p0_0: endpoint { |
| dai-format = "i2s"; |
| mclk-fs = <256>; |
| remote-endpoint = <&es8316_p0_0>; |
| }; |
| }; |
| }; |
| |
| &package_thermal { |
| polling-delay = <1000>; |
| |
| trips { |
| package_fan0: package-fan0 { |
| temperature = <55000>; |
| hysteresis = <2000>; |
| type = "active"; |
| }; |
| |
| package_fan1: package-fan1 { |
| temperature = <65000>; |
| hysteresis = <2000>; |
| type = "active"; |
| }; |
| }; |
| |
| cooling-maps { |
| map0 { |
| trip = <&package_fan0>; |
| cooling-device = <&fan THERMAL_NO_LIMIT 1>; |
| }; |
| |
| map1 { |
| trip = <&package_fan1>; |
| cooling-device = <&fan 2 THERMAL_NO_LIMIT>; |
| }; |
| }; |
| }; |
| |
| &pcie2x1l0 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pcie2_0_rst>; |
| reset-gpios = <&gpio4 RK_PA5 GPIO_ACTIVE_HIGH>; |
| vpcie3v3-supply = <&vcc3v3_pcie2x1l0>; |
| status = "okay"; |
| }; |
| |
| &pcie2x1l2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pcie2_2_rst>; |
| reset-gpios = <&gpio3 RK_PB0 GPIO_ACTIVE_HIGH>; |
| vpcie3v3-supply = <&vcc3v3_pcie2x1l2>; |
| status = "okay"; |
| }; |
| |
| &pcie30phy { |
| status = "okay"; |
| }; |
| |
| &pcie3x4 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pcie3_rst>; |
| reset-gpios = <&gpio4 RK_PB6 GPIO_ACTIVE_HIGH>; |
| vpcie3v3-supply = <&vcc3v3_pcie30>; |
| status = "okay"; |
| }; |
| |
| &pinctrl { |
| hym8563 { |
| hym8563_int: hym8563-int { |
| rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| }; |
| |
| leds { |
| led_rgb_b: led-rgb-b { |
| rockchip,pins = <0 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| }; |
| |
| sound { |
| hp_detect: hp-detect { |
| rockchip,pins = <1 RK_PD5 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| }; |
| |
| pcie2 { |
| pcie2_0_rst: pcie2-0-rst { |
| rockchip,pins = <4 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| |
| pcie2_0_vcc3v3_en: pcie2-0-vcc-en { |
| rockchip,pins = <1 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| |
| pcie2_2_rst: pcie2-2-rst { |
| rockchip,pins = <3 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| }; |
| |
| pcie3 { |
| pcie3_rst: pcie3-rst { |
| rockchip,pins = <4 RK_PB6 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| |
| pcie3_vcc3v3_en: pcie3-vcc3v3-en { |
| rockchip,pins = <1 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| }; |
| |
| usb { |
| vcc5v0_host_en: vcc5v0-host-en { |
| rockchip,pins = <4 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>; |
| }; |
| }; |
| }; |
| |
| &pwm1 { |
| status = "okay"; |
| }; |
| |
| &saradc { |
| vref-supply = <&avcc_1v8_s0>; |
| status = "okay"; |
| }; |
| |
| &sdhci { |
| bus-width = <8>; |
| no-sdio; |
| no-sd; |
| non-removable; |
| mmc-hs400-1_8v; |
| mmc-hs400-enhanced-strobe; |
| status = "okay"; |
| }; |
| |
| &sdmmc { |
| max-frequency = <200000000>; |
| no-sdio; |
| no-mmc; |
| bus-width = <4>; |
| cap-mmc-highspeed; |
| cap-sd-highspeed; |
| cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>; |
| disable-wp; |
| sd-uhs-sdr104; |
| vmmc-supply = <&vcc_3v3_s3>; |
| vqmmc-supply = <&vccio_sd_s0>; |
| status = "okay"; |
| }; |
| |
| &sdio { |
| max-frequency = <200000000>; |
| no-sd; |
| no-mmc; |
| non-removable; |
| bus-width = <4>; |
| cap-sdio-irq; |
| disable-wp; |
| keep-power-in-suspend; |
| wakeup-source; |
| sd-uhs-sdr12; |
| sd-uhs-sdr25; |
| sd-uhs-sdr50; |
| sd-uhs-sdr104; |
| vmmc-supply = <&vcc3v3_pcie2x1l0>; |
| vqmmc-supply = <&vcc_1v8_s3>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&sdiom0_pins>; |
| status = "okay"; |
| }; |
| |
| &sfc { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&fspim2_pins>; |
| status = "okay"; |
| |
| flash@0 { |
| compatible = "jedec,spi-nor"; |
| reg = <0>; |
| spi-max-frequency = <104000000>; |
| spi-rx-bus-width = <4>; |
| spi-tx-bus-width = <1>; |
| }; |
| }; |
| |
| &uart6 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart6m1_xfer &uart6m1_ctsn &uart6m1_rtsn>; |
| status = "okay"; |
| }; |
| |
| &spi2 { |
| status = "okay"; |
| assigned-clocks = <&cru CLK_SPI2>; |
| assigned-clock-rates = <200000000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&spi2m2_cs0 &spi2m2_pins>; |
| num-cs = <1>; |
| |
| pmic@0 { |
| compatible = "rockchip,rk806"; |
| spi-max-frequency = <1000000>; |
| reg = <0x0>; |
| |
| interrupt-parent = <&gpio0>; |
| interrupts = <7 IRQ_TYPE_LEVEL_LOW>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pmic_pins>, <&rk806_dvs1_null>, |
| <&rk806_dvs2_null>, <&rk806_dvs3_null>; |
| |
| system-power-controller; |
| |
| vcc1-supply = <&vcc5v0_sys>; |
| vcc2-supply = <&vcc5v0_sys>; |
| vcc3-supply = <&vcc5v0_sys>; |
| vcc4-supply = <&vcc5v0_sys>; |
| vcc5-supply = <&vcc5v0_sys>; |
| vcc6-supply = <&vcc5v0_sys>; |
| vcc7-supply = <&vcc5v0_sys>; |
| vcc8-supply = <&vcc5v0_sys>; |
| vcc9-supply = <&vcc5v0_sys>; |
| vcc10-supply = <&vcc5v0_sys>; |
| vcc11-supply = <&vcc_2v0_pldo_s3>; |
| vcc12-supply = <&vcc5v0_sys>; |
| vcc13-supply = <&vcc_1v1_nldo_s3>; |
| vcc14-supply = <&vcc_1v1_nldo_s3>; |
| vcca-supply = <&vcc5v0_sys>; |
| |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| rk806_dvs1_null: dvs1-null-pins { |
| pins = "gpio_pwrctrl1"; |
| function = "pin_fun0"; |
| }; |
| |
| rk806_dvs2_null: dvs2-null-pins { |
| pins = "gpio_pwrctrl2"; |
| function = "pin_fun0"; |
| }; |
| |
| rk806_dvs3_null: dvs3-null-pins { |
| pins = "gpio_pwrctrl3"; |
| function = "pin_fun0"; |
| }; |
| |
| regulators { |
| vdd_gpu_s0: vdd_gpu_mem_s0: dcdc-reg1 { |
| regulator-boot-on; |
| regulator-min-microvolt = <550000>; |
| regulator-max-microvolt = <950000>; |
| regulator-ramp-delay = <12500>; |
| regulator-name = "vdd_gpu_s0"; |
| regulator-enable-ramp-delay = <400>; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| vdd_cpu_lit_s0: vdd_cpu_lit_mem_s0: dcdc-reg2 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <550000>; |
| regulator-max-microvolt = <950000>; |
| regulator-ramp-delay = <12500>; |
| regulator-name = "vdd_cpu_lit_s0"; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| vdd_log_s0: dcdc-reg3 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <675000>; |
| regulator-max-microvolt = <750000>; |
| regulator-ramp-delay = <12500>; |
| regulator-name = "vdd_log_s0"; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| regulator-suspend-microvolt = <750000>; |
| }; |
| }; |
| |
| vdd_vdenc_s0: vdd_vdenc_mem_s0: dcdc-reg4 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <550000>; |
| regulator-max-microvolt = <950000>; |
| regulator-ramp-delay = <12500>; |
| regulator-name = "vdd_vdenc_s0"; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| vdd_ddr_s0: dcdc-reg5 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <675000>; |
| regulator-max-microvolt = <900000>; |
| regulator-ramp-delay = <12500>; |
| regulator-name = "vdd_ddr_s0"; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| regulator-suspend-microvolt = <850000>; |
| }; |
| }; |
| |
| vdd2_ddr_s3: dcdc-reg6 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-name = "vdd2_ddr_s3"; |
| |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| }; |
| }; |
| |
| vcc_2v0_pldo_s3: dcdc-reg7 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <2000000>; |
| regulator-max-microvolt = <2000000>; |
| regulator-ramp-delay = <12500>; |
| regulator-name = "vdd_2v0_pldo_s3"; |
| |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| regulator-suspend-microvolt = <2000000>; |
| }; |
| }; |
| |
| vcc_3v3_s3: dcdc-reg8 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-name = "vcc_3v3_s3"; |
| |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| regulator-suspend-microvolt = <3300000>; |
| }; |
| }; |
| |
| vddq_ddr_s0: dcdc-reg9 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-name = "vddq_ddr_s0"; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| vcc_1v8_s3: dcdc-reg10 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-name = "vcc_1v8_s3"; |
| |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| regulator-suspend-microvolt = <1800000>; |
| }; |
| }; |
| |
| avcc_1v8_s0: pldo-reg1 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-name = "avcc_1v8_s0"; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| vcc_1v8_s0: pldo-reg2 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-name = "vcc_1v8_s0"; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| regulator-suspend-microvolt = <1800000>; |
| }; |
| }; |
| |
| avdd_1v2_s0: pldo-reg3 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-name = "avdd_1v2_s0"; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| vcc_3v3_s0: pldo-reg4 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-ramp-delay = <12500>; |
| regulator-name = "vcc_3v3_s0"; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| vccio_sd_s0: pldo-reg5 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-ramp-delay = <12500>; |
| regulator-name = "vccio_sd_s0"; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| pldo6_s3: pldo-reg6 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-name = "pldo6_s3"; |
| |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| regulator-suspend-microvolt = <1800000>; |
| }; |
| }; |
| |
| vdd_0v75_s3: nldo-reg1 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <750000>; |
| regulator-max-microvolt = <750000>; |
| regulator-name = "vdd_0v75_s3"; |
| |
| regulator-state-mem { |
| regulator-on-in-suspend; |
| regulator-suspend-microvolt = <750000>; |
| }; |
| }; |
| |
| vdd_ddr_pll_s0: nldo-reg2 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <850000>; |
| regulator-max-microvolt = <850000>; |
| regulator-name = "vdd_ddr_pll_s0"; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| regulator-suspend-microvolt = <850000>; |
| }; |
| }; |
| |
| avdd_0v75_s0: nldo-reg3 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <750000>; |
| regulator-max-microvolt = <750000>; |
| regulator-name = "avdd_0v75_s0"; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| vdd_0v85_s0: nldo-reg4 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <850000>; |
| regulator-max-microvolt = <850000>; |
| regulator-name = "vdd_0v85_s0"; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| |
| vdd_0v75_s0: nldo-reg5 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <750000>; |
| regulator-max-microvolt = <750000>; |
| regulator-name = "vdd_0v75_s0"; |
| |
| regulator-state-mem { |
| regulator-off-in-suspend; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| &tsadc { |
| status = "okay"; |
| }; |
| |
| &uart2 { |
| pinctrl-0 = <&uart2m0_xfer>; |
| status = "okay"; |
| }; |
| |
| &u2phy1 { |
| status = "okay"; |
| }; |
| |
| &u2phy1_otg { |
| status = "okay"; |
| }; |
| |
| &u2phy2 { |
| status = "okay"; |
| }; |
| |
| &u2phy2_host { |
| /* connected to USB hub, which is powered by vcc5v0_sys */ |
| phy-supply = <&vcc5v0_sys>; |
| status = "okay"; |
| }; |
| |
| &u2phy3 { |
| status = "okay"; |
| }; |
| |
| &u2phy3_host { |
| phy-supply = <&vcc5v0_host>; |
| status = "okay"; |
| }; |
| |
| &usbdp_phy1 { |
| status = "okay"; |
| }; |
| |
| &usb_host0_ehci { |
| status = "okay"; |
| }; |
| |
| &usb_host0_ohci { |
| status = "okay"; |
| }; |
| |
| &usb_host1_ehci { |
| status = "okay"; |
| }; |
| |
| &usb_host1_ohci { |
| status = "okay"; |
| }; |
| |
| &usb_host1_xhci { |
| dr_mode = "host"; |
| status = "okay"; |
| }; |
| |
| &usb_host2_xhci { |
| status = "okay"; |
| }; |
