| // SPDX-License-Identifier: GPL-2.0-only |
| /* |
| * DRM driver for Solomon SSD13xx OLED displays |
| * |
| * Copyright 2022 Red Hat Inc. |
| * Author: Javier Martinez Canillas <javierm@redhat.com> |
| * |
| * Based on drivers/video/fbdev/ssd1307fb.c |
| * Copyright 2012 Free Electrons |
| */ |
| |
| #include <linux/backlight.h> |
| #include <linux/bitfield.h> |
| #include <linux/bits.h> |
| #include <linux/delay.h> |
| #include <linux/gpio/consumer.h> |
| #include <linux/property.h> |
| #include <linux/pwm.h> |
| #include <linux/regulator/consumer.h> |
| |
| #include <drm/drm_atomic.h> |
| #include <drm/drm_atomic_helper.h> |
| #include <drm/drm_crtc_helper.h> |
| #include <drm/drm_damage_helper.h> |
| #include <drm/drm_edid.h> |
| #include <drm/drm_fbdev_shmem.h> |
| #include <drm/drm_format_helper.h> |
| #include <drm/drm_framebuffer.h> |
| #include <drm/drm_gem_atomic_helper.h> |
| #include <drm/drm_gem_framebuffer_helper.h> |
| #include <drm/drm_gem_shmem_helper.h> |
| #include <drm/drm_managed.h> |
| #include <drm/drm_modes.h> |
| #include <drm/drm_rect.h> |
| #include <drm/drm_probe_helper.h> |
| |
| #include "ssd130x.h" |
| |
| #define DRIVER_NAME "ssd130x" |
| #define DRIVER_DESC "DRM driver for Solomon SSD13xx OLED displays" |
| #define DRIVER_DATE "20220131" |
| #define DRIVER_MAJOR 1 |
| #define DRIVER_MINOR 0 |
| |
| #define SSD130X_PAGE_HEIGHT 8 |
| |
| #define SSD132X_SEGMENT_WIDTH 2 |
| |
| /* ssd13xx commands */ |
| #define SSD13XX_CONTRAST 0x81 |
| #define SSD13XX_SET_SEG_REMAP 0xa0 |
| #define SSD13XX_SET_MULTIPLEX_RATIO 0xa8 |
| #define SSD13XX_DISPLAY_OFF 0xae |
| #define SSD13XX_DISPLAY_ON 0xaf |
| |
| #define SSD13XX_SET_SEG_REMAP_MASK GENMASK(0, 0) |
| #define SSD13XX_SET_SEG_REMAP_SET(val) FIELD_PREP(SSD13XX_SET_SEG_REMAP_MASK, (val)) |
| |
| /* ssd130x commands */ |
| #define SSD130X_PAGE_COL_START_LOW 0x00 |
| #define SSD130X_PAGE_COL_START_HIGH 0x10 |
| #define SSD130X_SET_ADDRESS_MODE 0x20 |
| #define SSD130X_SET_COL_RANGE 0x21 |
| #define SSD130X_SET_PAGE_RANGE 0x22 |
| #define SSD130X_SET_LOOKUP_TABLE 0x91 |
| #define SSD130X_CHARGE_PUMP 0x8d |
| #define SSD130X_START_PAGE_ADDRESS 0xb0 |
| #define SSD130X_SET_COM_SCAN_DIR 0xc0 |
| #define SSD130X_SET_DISPLAY_OFFSET 0xd3 |
| #define SSD130X_SET_CLOCK_FREQ 0xd5 |
| #define SSD130X_SET_AREA_COLOR_MODE 0xd8 |
| #define SSD130X_SET_PRECHARGE_PERIOD 0xd9 |
| #define SSD130X_SET_COM_PINS_CONFIG 0xda |
| #define SSD130X_SET_VCOMH 0xdb |
| |
| /* ssd130x commands accessors */ |
| #define SSD130X_PAGE_COL_START_MASK GENMASK(3, 0) |
| #define SSD130X_PAGE_COL_START_HIGH_SET(val) FIELD_PREP(SSD130X_PAGE_COL_START_MASK, (val) >> 4) |
| #define SSD130X_PAGE_COL_START_LOW_SET(val) FIELD_PREP(SSD130X_PAGE_COL_START_MASK, (val)) |
| #define SSD130X_START_PAGE_ADDRESS_MASK GENMASK(2, 0) |
| #define SSD130X_START_PAGE_ADDRESS_SET(val) FIELD_PREP(SSD130X_START_PAGE_ADDRESS_MASK, (val)) |
| #define SSD130X_SET_COM_SCAN_DIR_MASK GENMASK(3, 3) |
| #define SSD130X_SET_COM_SCAN_DIR_SET(val) FIELD_PREP(SSD130X_SET_COM_SCAN_DIR_MASK, (val)) |
| #define SSD130X_SET_CLOCK_DIV_MASK GENMASK(3, 0) |
| #define SSD130X_SET_CLOCK_DIV_SET(val) FIELD_PREP(SSD130X_SET_CLOCK_DIV_MASK, (val)) |
| #define SSD130X_SET_CLOCK_FREQ_MASK GENMASK(7, 4) |
| #define SSD130X_SET_CLOCK_FREQ_SET(val) FIELD_PREP(SSD130X_SET_CLOCK_FREQ_MASK, (val)) |
| #define SSD130X_SET_PRECHARGE_PERIOD1_MASK GENMASK(3, 0) |
| #define SSD130X_SET_PRECHARGE_PERIOD1_SET(val) FIELD_PREP(SSD130X_SET_PRECHARGE_PERIOD1_MASK, (val)) |
| #define SSD130X_SET_PRECHARGE_PERIOD2_MASK GENMASK(7, 4) |
| #define SSD130X_SET_PRECHARGE_PERIOD2_SET(val) FIELD_PREP(SSD130X_SET_PRECHARGE_PERIOD2_MASK, (val)) |
| #define SSD130X_SET_COM_PINS_CONFIG1_MASK GENMASK(4, 4) |
| #define SSD130X_SET_COM_PINS_CONFIG1_SET(val) FIELD_PREP(SSD130X_SET_COM_PINS_CONFIG1_MASK, (val)) |
| #define SSD130X_SET_COM_PINS_CONFIG2_MASK GENMASK(5, 5) |
| #define SSD130X_SET_COM_PINS_CONFIG2_SET(val) FIELD_PREP(SSD130X_SET_COM_PINS_CONFIG2_MASK, (val)) |
| |
| #define SSD130X_SET_ADDRESS_MODE_HORIZONTAL 0x00 |
| #define SSD130X_SET_ADDRESS_MODE_VERTICAL 0x01 |
| #define SSD130X_SET_ADDRESS_MODE_PAGE 0x02 |
| |
| #define SSD130X_SET_AREA_COLOR_MODE_ENABLE 0x1e |
| #define SSD130X_SET_AREA_COLOR_MODE_LOW_POWER 0x05 |
| |
| /* ssd132x commands */ |
| #define SSD132X_SET_COL_RANGE 0x15 |
| #define SSD132X_SET_DEACTIVATE_SCROLL 0x2e |
| #define SSD132X_SET_ROW_RANGE 0x75 |
| #define SSD132X_SET_DISPLAY_START 0xa1 |
| #define SSD132X_SET_DISPLAY_OFFSET 0xa2 |
| #define SSD132X_SET_DISPLAY_NORMAL 0xa4 |
| #define SSD132X_SET_FUNCTION_SELECT_A 0xab |
| #define SSD132X_SET_PHASE_LENGTH 0xb1 |
| #define SSD132X_SET_CLOCK_FREQ 0xb3 |
| #define SSD132X_SET_GPIO 0xb5 |
| #define SSD132X_SET_PRECHARGE_PERIOD 0xb6 |
| #define SSD132X_SET_GRAY_SCALE_TABLE 0xb8 |
| #define SSD132X_SELECT_DEFAULT_TABLE 0xb9 |
| #define SSD132X_SET_PRECHARGE_VOLTAGE 0xbc |
| #define SSD130X_SET_VCOMH_VOLTAGE 0xbe |
| #define SSD132X_SET_FUNCTION_SELECT_B 0xd5 |
| |
| /* ssd133x commands */ |
| #define SSD133X_SET_COL_RANGE 0x15 |
| #define SSD133X_SET_ROW_RANGE 0x75 |
| #define SSD133X_CONTRAST_A 0x81 |
| #define SSD133X_CONTRAST_B 0x82 |
| #define SSD133X_CONTRAST_C 0x83 |
| #define SSD133X_SET_MASTER_CURRENT 0x87 |
| #define SSD132X_SET_PRECHARGE_A 0x8a |
| #define SSD132X_SET_PRECHARGE_B 0x8b |
| #define SSD132X_SET_PRECHARGE_C 0x8c |
| #define SSD133X_SET_DISPLAY_START 0xa1 |
| #define SSD133X_SET_DISPLAY_OFFSET 0xa2 |
| #define SSD133X_SET_DISPLAY_NORMAL 0xa4 |
| #define SSD133X_SET_MASTER_CONFIG 0xad |
| #define SSD133X_POWER_SAVE_MODE 0xb0 |
| #define SSD133X_PHASES_PERIOD 0xb1 |
| #define SSD133X_SET_CLOCK_FREQ 0xb3 |
| #define SSD133X_SET_PRECHARGE_VOLTAGE 0xbb |
| #define SSD133X_SET_VCOMH_VOLTAGE 0xbe |
| |
| #define MAX_CONTRAST 255 |
| |
| const struct ssd130x_deviceinfo ssd130x_variants[] = { |
| [SH1106_ID] = { |
| .default_vcomh = 0x40, |
| .default_dclk_div = 1, |
| .default_dclk_frq = 5, |
| .default_width = 132, |
| .default_height = 64, |
| .page_mode_only = 1, |
| .family_id = SSD130X_FAMILY, |
| }, |
| [SSD1305_ID] = { |
| .default_vcomh = 0x34, |
| .default_dclk_div = 1, |
| .default_dclk_frq = 7, |
| .default_width = 132, |
| .default_height = 64, |
| .family_id = SSD130X_FAMILY, |
| }, |
| [SSD1306_ID] = { |
| .default_vcomh = 0x20, |
| .default_dclk_div = 1, |
| .default_dclk_frq = 8, |
| .need_chargepump = 1, |
| .default_width = 128, |
| .default_height = 64, |
| .family_id = SSD130X_FAMILY, |
| }, |
| [SSD1307_ID] = { |
| .default_vcomh = 0x20, |
| .default_dclk_div = 2, |
| .default_dclk_frq = 12, |
| .need_pwm = 1, |
| .default_width = 128, |
| .default_height = 39, |
| .family_id = SSD130X_FAMILY, |
| }, |
| [SSD1309_ID] = { |
| .default_vcomh = 0x34, |
| .default_dclk_div = 1, |
| .default_dclk_frq = 10, |
| .default_width = 128, |
| .default_height = 64, |
| .family_id = SSD130X_FAMILY, |
| }, |
| /* ssd132x family */ |
| [SSD1322_ID] = { |
| .default_width = 480, |
| .default_height = 128, |
| .family_id = SSD132X_FAMILY, |
| }, |
| [SSD1325_ID] = { |
| .default_width = 128, |
| .default_height = 80, |
| .family_id = SSD132X_FAMILY, |
| }, |
| [SSD1327_ID] = { |
| .default_width = 128, |
| .default_height = 128, |
| .family_id = SSD132X_FAMILY, |
| }, |
| /* ssd133x family */ |
| [SSD1331_ID] = { |
| .default_width = 96, |
| .default_height = 64, |
| .family_id = SSD133X_FAMILY, |
| } |
| }; |
| EXPORT_SYMBOL_NS_GPL(ssd130x_variants, DRM_SSD130X); |
| |
| struct ssd130x_crtc_state { |
| struct drm_crtc_state base; |
| /* Buffer to store pixels in HW format and written to the panel */ |
| u8 *data_array; |
| }; |
| |
| struct ssd130x_plane_state { |
| struct drm_shadow_plane_state base; |
| /* Intermediate buffer to convert pixels from XRGB8888 to HW format */ |
| u8 *buffer; |
| }; |
| |
| static inline struct ssd130x_crtc_state *to_ssd130x_crtc_state(struct drm_crtc_state *state) |
| { |
| return container_of(state, struct ssd130x_crtc_state, base); |
| } |
| |
| static inline struct ssd130x_plane_state *to_ssd130x_plane_state(struct drm_plane_state *state) |
| { |
| return container_of(state, struct ssd130x_plane_state, base.base); |
| } |
| |
| static inline struct ssd130x_device *drm_to_ssd130x(struct drm_device *drm) |
| { |
| return container_of(drm, struct ssd130x_device, drm); |
| } |
| |
| /* |
| * Helper to write data (SSD13XX_DATA) to the device. |
| */ |
| static int ssd130x_write_data(struct ssd130x_device *ssd130x, u8 *values, int count) |
| { |
| return regmap_bulk_write(ssd130x->regmap, SSD13XX_DATA, values, count); |
| } |
| |
| /* |
| * Helper to write command (SSD13XX_COMMAND). The fist variadic argument |
| * is the command to write and the following are the command options. |
| * |
| * Note that the ssd13xx protocol requires each command and option to be |
| * written as a SSD13XX_COMMAND device register value. That is why a call |
| * to regmap_write(..., SSD13XX_COMMAND, ...) is done for each argument. |
| */ |
| static int ssd130x_write_cmd(struct ssd130x_device *ssd130x, int count, |
| /* u8 cmd, u8 option, ... */...) |
| { |
| va_list ap; |
| u8 value; |
| int ret; |
| |
| va_start(ap, count); |
| |
| do { |
| value = va_arg(ap, int); |
| ret = regmap_write(ssd130x->regmap, SSD13XX_COMMAND, value); |
| if (ret) |
| goto out_end; |
| } while (--count); |
| |
| out_end: |
| va_end(ap); |
| |
| return ret; |
| } |
| |
| /* Set address range for horizontal/vertical addressing modes */ |
| static int ssd130x_set_col_range(struct ssd130x_device *ssd130x, |
| u8 col_start, u8 cols) |
| { |
| u8 col_end = col_start + cols - 1; |
| int ret; |
| |
| if (col_start == ssd130x->col_start && col_end == ssd130x->col_end) |
| return 0; |
| |
| ret = ssd130x_write_cmd(ssd130x, 3, SSD130X_SET_COL_RANGE, col_start, col_end); |
| if (ret < 0) |
| return ret; |
| |
| ssd130x->col_start = col_start; |
| ssd130x->col_end = col_end; |
| return 0; |
| } |
| |
| static int ssd130x_set_page_range(struct ssd130x_device *ssd130x, |
| u8 page_start, u8 pages) |
| { |
| u8 page_end = page_start + pages - 1; |
| int ret; |
| |
| if (page_start == ssd130x->page_start && page_end == ssd130x->page_end) |
| return 0; |
| |
| ret = ssd130x_write_cmd(ssd130x, 3, SSD130X_SET_PAGE_RANGE, page_start, page_end); |
| if (ret < 0) |
| return ret; |
| |
| ssd130x->page_start = page_start; |
| ssd130x->page_end = page_end; |
| return 0; |
| } |
| |
| /* Set page and column start address for page addressing mode */ |
| static int ssd130x_set_page_pos(struct ssd130x_device *ssd130x, |
| u8 page_start, u8 col_start) |
| { |
| int ret; |
| u32 page, col_low, col_high; |
| |
| page = SSD130X_START_PAGE_ADDRESS | |
| SSD130X_START_PAGE_ADDRESS_SET(page_start); |
| col_low = SSD130X_PAGE_COL_START_LOW | |
| SSD130X_PAGE_COL_START_LOW_SET(col_start); |
| col_high = SSD130X_PAGE_COL_START_HIGH | |
| SSD130X_PAGE_COL_START_HIGH_SET(col_start); |
| ret = ssd130x_write_cmd(ssd130x, 3, page, col_low, col_high); |
| if (ret < 0) |
| return ret; |
| |
| return 0; |
| } |
| |
| static int ssd130x_pwm_enable(struct ssd130x_device *ssd130x) |
| { |
| struct device *dev = ssd130x->dev; |
| struct pwm_state pwmstate; |
| |
| ssd130x->pwm = pwm_get(dev, NULL); |
| if (IS_ERR(ssd130x->pwm)) { |
| dev_err(dev, "Could not get PWM from firmware description!\n"); |
| return PTR_ERR(ssd130x->pwm); |
| } |
| |
| pwm_init_state(ssd130x->pwm, &pwmstate); |
| pwm_set_relative_duty_cycle(&pwmstate, 50, 100); |
| pwm_apply_might_sleep(ssd130x->pwm, &pwmstate); |
| |
| /* Enable the PWM */ |
| pwm_enable(ssd130x->pwm); |
| |
| dev_dbg(dev, "Using PWM %s with a %lluns period.\n", |
| ssd130x->pwm->label, pwm_get_period(ssd130x->pwm)); |
| |
| return 0; |
| } |
| |
| static void ssd130x_reset(struct ssd130x_device *ssd130x) |
| { |
| if (!ssd130x->reset) |
| return; |
| |
| /* Reset the screen */ |
| gpiod_set_value_cansleep(ssd130x->reset, 1); |
| udelay(4); |
| gpiod_set_value_cansleep(ssd130x->reset, 0); |
| udelay(4); |
| } |
| |
| static int ssd130x_power_on(struct ssd130x_device *ssd130x) |
| { |
| struct device *dev = ssd130x->dev; |
| int ret; |
| |
| ssd130x_reset(ssd130x); |
| |
| ret = regulator_enable(ssd130x->vcc_reg); |
| if (ret) { |
| dev_err(dev, "Failed to enable VCC: %d\n", ret); |
| return ret; |
| } |
| |
| if (ssd130x->device_info->need_pwm) { |
| ret = ssd130x_pwm_enable(ssd130x); |
| if (ret) { |
| dev_err(dev, "Failed to enable PWM: %d\n", ret); |
| regulator_disable(ssd130x->vcc_reg); |
| return ret; |
| } |
| } |
| |
| return 0; |
| } |
| |
| static void ssd130x_power_off(struct ssd130x_device *ssd130x) |
| { |
| pwm_disable(ssd130x->pwm); |
| pwm_put(ssd130x->pwm); |
| |
| regulator_disable(ssd130x->vcc_reg); |
| } |
| |
| static int ssd130x_init(struct ssd130x_device *ssd130x) |
| { |
| u32 precharge, dclk, com_invdir, compins, chargepump, seg_remap; |
| bool scan_mode; |
| int ret; |
| |
| /* Set initial contrast */ |
| ret = ssd130x_write_cmd(ssd130x, 2, SSD13XX_CONTRAST, ssd130x->contrast); |
| if (ret < 0) |
| return ret; |
| |
| /* Set segment re-map */ |
| seg_remap = (SSD13XX_SET_SEG_REMAP | |
| SSD13XX_SET_SEG_REMAP_SET(ssd130x->seg_remap)); |
| ret = ssd130x_write_cmd(ssd130x, 1, seg_remap); |
| if (ret < 0) |
| return ret; |
| |
| /* Set COM direction */ |
| com_invdir = (SSD130X_SET_COM_SCAN_DIR | |
| SSD130X_SET_COM_SCAN_DIR_SET(ssd130x->com_invdir)); |
| ret = ssd130x_write_cmd(ssd130x, 1, com_invdir); |
| if (ret < 0) |
| return ret; |
| |
| /* Set multiplex ratio value */ |
| ret = ssd130x_write_cmd(ssd130x, 2, SSD13XX_SET_MULTIPLEX_RATIO, ssd130x->height - 1); |
| if (ret < 0) |
| return ret; |
| |
| /* set display offset value */ |
| ret = ssd130x_write_cmd(ssd130x, 2, SSD130X_SET_DISPLAY_OFFSET, ssd130x->com_offset); |
| if (ret < 0) |
| return ret; |
| |
| /* Set clock frequency */ |
| dclk = (SSD130X_SET_CLOCK_DIV_SET(ssd130x->dclk_div - 1) | |
| SSD130X_SET_CLOCK_FREQ_SET(ssd130x->dclk_frq)); |
| ret = ssd130x_write_cmd(ssd130x, 2, SSD130X_SET_CLOCK_FREQ, dclk); |
| if (ret < 0) |
| return ret; |
| |
| /* Set Area Color Mode ON/OFF & Low Power Display Mode */ |
| if (ssd130x->area_color_enable || ssd130x->low_power) { |
| u32 mode = 0; |
| |
| if (ssd130x->area_color_enable) |
| mode |= SSD130X_SET_AREA_COLOR_MODE_ENABLE; |
| |
| if (ssd130x->low_power) |
| mode |= SSD130X_SET_AREA_COLOR_MODE_LOW_POWER; |
| |
| ret = ssd130x_write_cmd(ssd130x, 2, SSD130X_SET_AREA_COLOR_MODE, mode); |
| if (ret < 0) |
| return ret; |
| } |
| |
| /* Set precharge period in number of ticks from the internal clock */ |
| precharge = (SSD130X_SET_PRECHARGE_PERIOD1_SET(ssd130x->prechargep1) | |
| SSD130X_SET_PRECHARGE_PERIOD2_SET(ssd130x->prechargep2)); |
| ret = ssd130x_write_cmd(ssd130x, 2, SSD130X_SET_PRECHARGE_PERIOD, precharge); |
| if (ret < 0) |
| return ret; |
| |
| /* Set COM pins configuration */ |
| compins = BIT(1); |
| /* |
| * The COM scan mode field values are the inverse of the boolean DT |
| * property "solomon,com-seq". The value 0b means scan from COM0 to |
| * COM[N - 1] while 1b means scan from COM[N - 1] to COM0. |
| */ |
| scan_mode = !ssd130x->com_seq; |
| compins |= (SSD130X_SET_COM_PINS_CONFIG1_SET(scan_mode) | |
| SSD130X_SET_COM_PINS_CONFIG2_SET(ssd130x->com_lrremap)); |
| ret = ssd130x_write_cmd(ssd130x, 2, SSD130X_SET_COM_PINS_CONFIG, compins); |
| if (ret < 0) |
| return ret; |
| |
| /* Set VCOMH */ |
| ret = ssd130x_write_cmd(ssd130x, 2, SSD130X_SET_VCOMH, ssd130x->vcomh); |
| if (ret < 0) |
| return ret; |
| |
| /* Turn on the DC-DC Charge Pump */ |
| chargepump = BIT(4); |
| |
| if (ssd130x->device_info->need_chargepump) |
| chargepump |= BIT(2); |
| |
| ret = ssd130x_write_cmd(ssd130x, 2, SSD130X_CHARGE_PUMP, chargepump); |
| if (ret < 0) |
| return ret; |
| |
| /* Set lookup table */ |
| if (ssd130x->lookup_table_set) { |
| int i; |
| |
| ret = ssd130x_write_cmd(ssd130x, 1, SSD130X_SET_LOOKUP_TABLE); |
| if (ret < 0) |
| return ret; |
| |
| for (i = 0; i < ARRAY_SIZE(ssd130x->lookup_table); i++) { |
| u8 val = ssd130x->lookup_table[i]; |
| |
| if (val < 31 || val > 63) |
| dev_warn(ssd130x->dev, |
| "lookup table index %d value out of range 31 <= %d <= 63\n", |
| i, val); |
| ret = ssd130x_write_cmd(ssd130x, 1, val); |
| if (ret < 0) |
| return ret; |
| } |
| } |
| |
| /* Switch to page addressing mode */ |
| if (ssd130x->page_address_mode) |
| return ssd130x_write_cmd(ssd130x, 2, SSD130X_SET_ADDRESS_MODE, |
| SSD130X_SET_ADDRESS_MODE_PAGE); |
| |
| /* Switch to horizontal addressing mode */ |
| return ssd130x_write_cmd(ssd130x, 2, SSD130X_SET_ADDRESS_MODE, |
| SSD130X_SET_ADDRESS_MODE_HORIZONTAL); |
| } |
| |
| static int ssd132x_init(struct ssd130x_device *ssd130x) |
| { |
| int ret; |
| |
| /* Set initial contrast */ |
| ret = ssd130x_write_cmd(ssd130x, 2, SSD13XX_CONTRAST, 0x80); |
| if (ret < 0) |
| return ret; |
| |
| /* Set column start and end */ |
| ret = ssd130x_write_cmd(ssd130x, 3, SSD132X_SET_COL_RANGE, 0x00, |
| ssd130x->width / SSD132X_SEGMENT_WIDTH - 1); |
| if (ret < 0) |
| return ret; |
| |
| /* Set row start and end */ |
| ret = ssd130x_write_cmd(ssd130x, 3, SSD132X_SET_ROW_RANGE, 0x00, ssd130x->height - 1); |
| if (ret < 0) |
| return ret; |
| /* |
| * Horizontal Address Increment |
| * Re-map for Column Address, Nibble and COM |
| * COM Split Odd Even |
| */ |
| ret = ssd130x_write_cmd(ssd130x, 2, SSD13XX_SET_SEG_REMAP, 0x53); |
| if (ret < 0) |
| return ret; |
| |
| /* Set display start and offset */ |
| ret = ssd130x_write_cmd(ssd130x, 2, SSD132X_SET_DISPLAY_START, 0x00); |
| if (ret < 0) |
| return ret; |
| |
| ret = ssd130x_write_cmd(ssd130x, 2, SSD132X_SET_DISPLAY_OFFSET, 0x00); |
| if (ret < 0) |
| return ret; |
| |
| /* Set display mode normal */ |
| ret = ssd130x_write_cmd(ssd130x, 1, SSD132X_SET_DISPLAY_NORMAL); |
| if (ret < 0) |
| return ret; |
| |
| /* Set multiplex ratio value */ |
| ret = ssd130x_write_cmd(ssd130x, 2, SSD13XX_SET_MULTIPLEX_RATIO, ssd130x->height - 1); |
| if (ret < 0) |
| return ret; |
| |
| /* Set phase length */ |
| ret = ssd130x_write_cmd(ssd130x, 2, SSD132X_SET_PHASE_LENGTH, 0x55); |
| if (ret < 0) |
| return ret; |
| |
| /* Select default linear gray scale table */ |
| ret = ssd130x_write_cmd(ssd130x, 1, SSD132X_SELECT_DEFAULT_TABLE); |
| if (ret < 0) |
| return ret; |
| |
| /* Set clock frequency */ |
| ret = ssd130x_write_cmd(ssd130x, 2, SSD132X_SET_CLOCK_FREQ, 0x01); |
| if (ret < 0) |
| return ret; |
| |
| /* Enable internal VDD regulator */ |
| ret = ssd130x_write_cmd(ssd130x, 2, SSD132X_SET_FUNCTION_SELECT_A, 0x1); |
| if (ret < 0) |
| return ret; |
| |
| /* Set pre-charge period */ |
| ret = ssd130x_write_cmd(ssd130x, 2, SSD132X_SET_PRECHARGE_PERIOD, 0x01); |
| if (ret < 0) |
| return ret; |
| |
| /* Set pre-charge voltage */ |
| ret = ssd130x_write_cmd(ssd130x, 2, SSD132X_SET_PRECHARGE_VOLTAGE, 0x08); |
| if (ret < 0) |
| return ret; |
| |
| /* Set VCOMH voltage */ |
| ret = ssd130x_write_cmd(ssd130x, 2, SSD130X_SET_VCOMH_VOLTAGE, 0x07); |
| if (ret < 0) |
| return ret; |
| |
| /* Enable second pre-charge and internal VSL */ |
| ret = ssd130x_write_cmd(ssd130x, 2, SSD132X_SET_FUNCTION_SELECT_B, 0x62); |
| if (ret < 0) |
| return ret; |
| |
| return 0; |
| } |
| |
| static int ssd133x_init(struct ssd130x_device *ssd130x) |
| { |
| int ret; |
| |
| /* Set color A contrast */ |
| ret = ssd130x_write_cmd(ssd130x, 2, SSD133X_CONTRAST_A, 0x91); |
| if (ret < 0) |
| return ret; |
| |
| /* Set color B contrast */ |
| ret = ssd130x_write_cmd(ssd130x, 2, SSD133X_CONTRAST_B, 0x50); |
| if (ret < 0) |
| return ret; |
| |
| /* Set color C contrast */ |
| ret = ssd130x_write_cmd(ssd130x, 2, SSD133X_CONTRAST_C, 0x7d); |
| if (ret < 0) |
| return ret; |
| |
| /* Set master current */ |
| ret = ssd130x_write_cmd(ssd130x, 2, SSD133X_SET_MASTER_CURRENT, 0x06); |
| if (ret < 0) |
| return ret; |
| |
| /* Set column start and end */ |
| ret = ssd130x_write_cmd(ssd130x, 3, SSD133X_SET_COL_RANGE, 0x00, ssd130x->width - 1); |
| if (ret < 0) |
| return ret; |
| |
| /* Set row start and end */ |
| ret = ssd130x_write_cmd(ssd130x, 3, SSD133X_SET_ROW_RANGE, 0x00, ssd130x->height - 1); |
| if (ret < 0) |
| return ret; |
| |
| /* |
| * Horizontal Address Increment |
| * Normal order SA,SB,SC (e.g. RGB) |
| * COM Split Odd Even |
| * 256 color format |
| */ |
| ret = ssd130x_write_cmd(ssd130x, 2, SSD13XX_SET_SEG_REMAP, 0x20); |
| if (ret < 0) |
| return ret; |
| |
| /* Set display start and offset */ |
| ret = ssd130x_write_cmd(ssd130x, 2, SSD133X_SET_DISPLAY_START, 0x00); |
| if (ret < 0) |
| return ret; |
| |
| ret = ssd130x_write_cmd(ssd130x, 2, SSD133X_SET_DISPLAY_OFFSET, 0x00); |
| if (ret < 0) |
| return ret; |
| |
| /* Set display mode normal */ |
| ret = ssd130x_write_cmd(ssd130x, 1, SSD133X_SET_DISPLAY_NORMAL); |
| if (ret < 0) |
| return ret; |
| |
| /* Set multiplex ratio value */ |
| ret = ssd130x_write_cmd(ssd130x, 2, SSD13XX_SET_MULTIPLEX_RATIO, ssd130x->height - 1); |
| if (ret < 0) |
| return ret; |
| |
| /* Set master configuration */ |
| ret = ssd130x_write_cmd(ssd130x, 2, SSD133X_SET_MASTER_CONFIG, 0x8e); |
| if (ret < 0) |
| return ret; |
| |
| /* Set power mode */ |
| ret = ssd130x_write_cmd(ssd130x, 2, SSD133X_POWER_SAVE_MODE, 0x0b); |
| if (ret < 0) |
| return ret; |
| |
| /* Set Phase 1 and 2 period */ |
| ret = ssd130x_write_cmd(ssd130x, 2, SSD133X_PHASES_PERIOD, 0x31); |
| if (ret < 0) |
| return ret; |
| |
| /* Set clock divider */ |
| ret = ssd130x_write_cmd(ssd130x, 2, SSD133X_SET_CLOCK_FREQ, 0xf0); |
| if (ret < 0) |
| return ret; |
| |
| /* Set pre-charge A */ |
| ret = ssd130x_write_cmd(ssd130x, 2, SSD132X_SET_PRECHARGE_A, 0x64); |
| if (ret < 0) |
| return ret; |
| |
| /* Set pre-charge B */ |
| ret = ssd130x_write_cmd(ssd130x, 2, SSD132X_SET_PRECHARGE_B, 0x78); |
| if (ret < 0) |
| return ret; |
| |
| /* Set pre-charge C */ |
| ret = ssd130x_write_cmd(ssd130x, 2, SSD132X_SET_PRECHARGE_C, 0x64); |
| if (ret < 0) |
| return ret; |
| |
| /* Set pre-charge level */ |
| ret = ssd130x_write_cmd(ssd130x, 2, SSD133X_SET_PRECHARGE_VOLTAGE, 0x3a); |
| if (ret < 0) |
| return ret; |
| |
| /* Set VCOMH voltage */ |
| ret = ssd130x_write_cmd(ssd130x, 2, SSD133X_SET_VCOMH_VOLTAGE, 0x3e); |
| if (ret < 0) |
| return ret; |
| |
| return 0; |
| } |
| |
| static int ssd130x_update_rect(struct ssd130x_device *ssd130x, |
| struct drm_rect *rect, u8 *buf, |
| u8 *data_array) |
| { |
| unsigned int x = rect->x1; |
| unsigned int y = rect->y1; |
| unsigned int width = drm_rect_width(rect); |
| unsigned int height = drm_rect_height(rect); |
| unsigned int line_length = DIV_ROUND_UP(width, 8); |
| unsigned int page_height = SSD130X_PAGE_HEIGHT; |
| unsigned int pages = DIV_ROUND_UP(height, page_height); |
| struct drm_device *drm = &ssd130x->drm; |
| u32 array_idx = 0; |
| int ret, i, j, k; |
| |
| drm_WARN_ONCE(drm, y % page_height != 0, "y must be aligned to screen page\n"); |
| |
| /* |
| * The screen is divided in pages, each having a height of 8 |
| * pixels, and the width of the screen. When sending a byte of |
| * data to the controller, it gives the 8 bits for the current |
| * column. I.e, the first byte are the 8 bits of the first |
| * column, then the 8 bits for the second column, etc. |
| * |
| * |
| * Representation of the screen, assuming it is 5 bits |
| * wide. Each letter-number combination is a bit that controls |
| * one pixel. |
| * |
| * A0 A1 A2 A3 A4 |
| * B0 B1 B2 B3 B4 |
| * C0 C1 C2 C3 C4 |
| * D0 D1 D2 D3 D4 |
| * E0 E1 E2 E3 E4 |
| * F0 F1 F2 F3 F4 |
| * G0 G1 G2 G3 G4 |
| * H0 H1 H2 H3 H4 |
| * |
| * If you want to update this screen, you need to send 5 bytes: |
| * (1) A0 B0 C0 D0 E0 F0 G0 H0 |
| * (2) A1 B1 C1 D1 E1 F1 G1 H1 |
| * (3) A2 B2 C2 D2 E2 F2 G2 H2 |
| * (4) A3 B3 C3 D3 E3 F3 G3 H3 |
| * (5) A4 B4 C4 D4 E4 F4 G4 H4 |
| */ |
| |
| if (!ssd130x->page_address_mode) { |
| u8 page_start; |
| |
| /* Set address range for horizontal addressing mode */ |
| ret = ssd130x_set_col_range(ssd130x, ssd130x->col_offset + x, width); |
| if (ret < 0) |
| return ret; |
| |
| page_start = ssd130x->page_offset + y / page_height; |
| ret = ssd130x_set_page_range(ssd130x, page_start, pages); |
| if (ret < 0) |
| return ret; |
| } |
| |
| for (i = 0; i < pages; i++) { |
| int m = page_height; |
| |
| /* Last page may be partial */ |
| if (page_height * (y / page_height + i + 1) > ssd130x->height) |
| m = ssd130x->height % page_height; |
| |
| for (j = 0; j < width; j++) { |
| u8 data = 0; |
| |
| for (k = 0; k < m; k++) { |
| u32 idx = (page_height * i + k) * line_length + j / 8; |
| u8 byte = buf[idx]; |
| u8 bit = (byte >> (j % 8)) & 1; |
| |
| data |= bit << k; |
| } |
| data_array[array_idx++] = data; |
| } |
| |
| /* |
| * In page addressing mode, the start address needs to be reset, |
| * and each page then needs to be written out separately. |
| */ |
| if (ssd130x->page_address_mode) { |
| ret = ssd130x_set_page_pos(ssd130x, |
| ssd130x->page_offset + i, |
| ssd130x->col_offset + x); |
| if (ret < 0) |
| return ret; |
| |
| ret = ssd130x_write_data(ssd130x, data_array, width); |
| if (ret < 0) |
| return ret; |
| |
| array_idx = 0; |
| } |
| } |
| |
| /* Write out update in one go if we aren't using page addressing mode */ |
| if (!ssd130x->page_address_mode) |
| ret = ssd130x_write_data(ssd130x, data_array, width * pages); |
| |
| return ret; |
| } |
| |
| static int ssd132x_update_rect(struct ssd130x_device *ssd130x, |
| struct drm_rect *rect, u8 *buf, |
| u8 *data_array) |
| { |
| unsigned int x = rect->x1; |
| unsigned int y = rect->y1; |
| unsigned int segment_width = SSD132X_SEGMENT_WIDTH; |
| unsigned int width = drm_rect_width(rect); |
| unsigned int height = drm_rect_height(rect); |
| unsigned int columns = DIV_ROUND_UP(width, segment_width); |
| unsigned int rows = height; |
| struct drm_device *drm = &ssd130x->drm; |
| u32 array_idx = 0; |
| unsigned int i, j; |
| int ret; |
| |
| drm_WARN_ONCE(drm, x % segment_width != 0, "x must be aligned to screen segment\n"); |
| |
| /* |
| * The screen is divided in Segment and Common outputs, where |
| * COM0 to COM[N - 1] are the rows and SEG0 to SEG[M - 1] are |
| * the columns. |
| * |
| * Each Segment has a 4-bit pixel and each Common output has a |
| * row of pixels. When using the (default) horizontal address |
| * increment mode, each byte of data sent to the controller has |
| * two Segments (e.g: SEG0 and SEG1) that are stored in the lower |
| * and higher nibbles of a single byte representing one column. |
| * That is, the first byte are SEG0 (D0[3:0]) and SEG1 (D0[7:4]), |
| * the second byte are SEG2 (D1[3:0]) and SEG3 (D1[7:4]) and so on. |
| */ |
| |
| /* Set column start and end */ |
| ret = ssd130x_write_cmd(ssd130x, 3, SSD132X_SET_COL_RANGE, x / segment_width, columns - 1); |
| if (ret < 0) |
| return ret; |
| |
| /* Set row start and end */ |
| ret = ssd130x_write_cmd(ssd130x, 3, SSD132X_SET_ROW_RANGE, y, rows - 1); |
| if (ret < 0) |
| return ret; |
| |
| for (i = 0; i < height; i++) { |
| /* Process pair of pixels and combine them into a single byte */ |
| for (j = 0; j < width; j += segment_width) { |
| u8 n1 = buf[i * width + j]; |
| u8 n2 = buf[i * width + j + 1]; |
| |
| data_array[array_idx++] = (n2 << 4) | n1; |
| } |
| } |
| |
| /* Write out update in one go since horizontal addressing mode is used */ |
| ret = ssd130x_write_data(ssd130x, data_array, columns * rows); |
| |
| return ret; |
| } |
| |
| static int ssd133x_update_rect(struct ssd130x_device *ssd130x, |
| struct drm_rect *rect, u8 *data_array, |
| unsigned int pitch) |
| { |
| unsigned int x = rect->x1; |
| unsigned int y = rect->y1; |
| unsigned int columns = drm_rect_width(rect); |
| unsigned int rows = drm_rect_height(rect); |
| int ret; |
| |
| /* |
| * The screen is divided in Segment and Common outputs, where |
| * COM0 to COM[N - 1] are the rows and SEG0 to SEG[M - 1] are |
| * the columns. |
| * |
| * Each Segment has a 8-bit pixel and each Common output has a |
| * row of pixels. When using the (default) horizontal address |
| * increment mode, each byte of data sent to the controller has |
| * a Segment (e.g: SEG0). |
| * |
| * When using the 256 color depth format, each pixel contains 3 |
| * sub-pixels for color A, B and C. These have 3 bit, 3 bit and |
| * 2 bits respectively. |
| */ |
| |
| /* Set column start and end */ |
| ret = ssd130x_write_cmd(ssd130x, 3, SSD133X_SET_COL_RANGE, x, columns - 1); |
| if (ret < 0) |
| return ret; |
| |
| /* Set row start and end */ |
| ret = ssd130x_write_cmd(ssd130x, 3, SSD133X_SET_ROW_RANGE, y, rows - 1); |
| if (ret < 0) |
| return ret; |
| |
| /* Write out update in one go since horizontal addressing mode is used */ |
| ret = ssd130x_write_data(ssd130x, data_array, pitch * rows); |
| |
| return ret; |
| } |
| |
| static void ssd130x_clear_screen(struct ssd130x_device *ssd130x, u8 *data_array) |
| { |
| unsigned int pages = DIV_ROUND_UP(ssd130x->height, SSD130X_PAGE_HEIGHT); |
| unsigned int width = ssd130x->width; |
| int ret, i; |
| |
| if (!ssd130x->page_address_mode) { |
| memset(data_array, 0, width * pages); |
| |
| /* Set address range for horizontal addressing mode */ |
| ret = ssd130x_set_col_range(ssd130x, ssd130x->col_offset, width); |
| if (ret < 0) |
| return; |
| |
| ret = ssd130x_set_page_range(ssd130x, ssd130x->page_offset, pages); |
| if (ret < 0) |
| return; |
| |
| /* Write out update in one go if we aren't using page addressing mode */ |
| ssd130x_write_data(ssd130x, data_array, width * pages); |
| } else { |
| /* |
| * In page addressing mode, the start address needs to be reset, |
| * and each page then needs to be written out separately. |
| */ |
| memset(data_array, 0, width); |
| |
| for (i = 0; i < pages; i++) { |
| ret = ssd130x_set_page_pos(ssd130x, |
| ssd130x->page_offset + i, |
| ssd130x->col_offset); |
| if (ret < 0) |
| return; |
| |
| ret = ssd130x_write_data(ssd130x, data_array, width); |
| if (ret < 0) |
| return; |
| } |
| } |
| } |
| |
| static void ssd132x_clear_screen(struct ssd130x_device *ssd130x, u8 *data_array) |
| { |
| unsigned int columns = DIV_ROUND_UP(ssd130x->height, SSD132X_SEGMENT_WIDTH); |
| unsigned int height = ssd130x->height; |
| |
| memset(data_array, 0, columns * height); |
| |
| /* Write out update in one go since horizontal addressing mode is used */ |
| ssd130x_write_data(ssd130x, data_array, columns * height); |
| } |
| |
| static void ssd133x_clear_screen(struct ssd130x_device *ssd130x, u8 *data_array) |
| { |
| const struct drm_format_info *fi = drm_format_info(DRM_FORMAT_RGB332); |
| unsigned int pitch; |
| |
| if (!fi) |
| return; |
| |
| pitch = drm_format_info_min_pitch(fi, 0, ssd130x->width); |
| |
| memset(data_array, 0, pitch * ssd130x->height); |
| |
| /* Write out update in one go since horizontal addressing mode is used */ |
| ssd130x_write_data(ssd130x, data_array, pitch * ssd130x->height); |
| } |
| |
| static int ssd130x_fb_blit_rect(struct drm_framebuffer *fb, |
| const struct iosys_map *vmap, |
| struct drm_rect *rect, |
| u8 *buf, u8 *data_array, |
| struct drm_format_conv_state *fmtcnv_state) |
| { |
| struct ssd130x_device *ssd130x = drm_to_ssd130x(fb->dev); |
| struct iosys_map dst; |
| unsigned int dst_pitch; |
| int ret = 0; |
| |
| /* Align y to display page boundaries */ |
| rect->y1 = round_down(rect->y1, SSD130X_PAGE_HEIGHT); |
| rect->y2 = min_t(unsigned int, round_up(rect->y2, SSD130X_PAGE_HEIGHT), ssd130x->height); |
| |
| dst_pitch = DIV_ROUND_UP(drm_rect_width(rect), 8); |
| |
| ret = drm_gem_fb_begin_cpu_access(fb, DMA_FROM_DEVICE); |
| if (ret) |
| return ret; |
| |
| iosys_map_set_vaddr(&dst, buf); |
| drm_fb_xrgb8888_to_mono(&dst, &dst_pitch, vmap, fb, rect, fmtcnv_state); |
| |
| drm_gem_fb_end_cpu_access(fb, DMA_FROM_DEVICE); |
| |
| ssd130x_update_rect(ssd130x, rect, buf, data_array); |
| |
| return ret; |
| } |
| |
| static int ssd132x_fb_blit_rect(struct drm_framebuffer *fb, |
| const struct iosys_map *vmap, |
| struct drm_rect *rect, u8 *buf, |
| u8 *data_array, |
| struct drm_format_conv_state *fmtcnv_state) |
| { |
| struct ssd130x_device *ssd130x = drm_to_ssd130x(fb->dev); |
| unsigned int dst_pitch = drm_rect_width(rect); |
| struct iosys_map dst; |
| int ret = 0; |
| |
| /* Align x to display segment boundaries */ |
| rect->x1 = round_down(rect->x1, SSD132X_SEGMENT_WIDTH); |
| rect->x2 = min_t(unsigned int, round_up(rect->x2, SSD132X_SEGMENT_WIDTH), |
| ssd130x->width); |
| |
| ret = drm_gem_fb_begin_cpu_access(fb, DMA_FROM_DEVICE); |
| if (ret) |
| return ret; |
| |
| iosys_map_set_vaddr(&dst, buf); |
| drm_fb_xrgb8888_to_gray8(&dst, &dst_pitch, vmap, fb, rect, fmtcnv_state); |
| |
| drm_gem_fb_end_cpu_access(fb, DMA_FROM_DEVICE); |
| |
| ssd132x_update_rect(ssd130x, rect, buf, data_array); |
| |
| return ret; |
| } |
| |
| static int ssd133x_fb_blit_rect(struct drm_framebuffer *fb, |
| const struct iosys_map *vmap, |
| struct drm_rect *rect, u8 *data_array, |
| struct drm_format_conv_state *fmtcnv_state) |
| { |
| struct ssd130x_device *ssd130x = drm_to_ssd130x(fb->dev); |
| const struct drm_format_info *fi = drm_format_info(DRM_FORMAT_RGB332); |
| unsigned int dst_pitch; |
| struct iosys_map dst; |
| int ret = 0; |
| |
| if (!fi) |
| return -EINVAL; |
| |
| dst_pitch = drm_format_info_min_pitch(fi, 0, drm_rect_width(rect)); |
| |
| ret = drm_gem_fb_begin_cpu_access(fb, DMA_FROM_DEVICE); |
| if (ret) |
| return ret; |
| |
| iosys_map_set_vaddr(&dst, data_array); |
| drm_fb_xrgb8888_to_rgb332(&dst, &dst_pitch, vmap, fb, rect, fmtcnv_state); |
| |
| drm_gem_fb_end_cpu_access(fb, DMA_FROM_DEVICE); |
| |
| ssd133x_update_rect(ssd130x, rect, data_array, dst_pitch); |
| |
| return ret; |
| } |
| |
| static int ssd130x_primary_plane_atomic_check(struct drm_plane *plane, |
| struct drm_atomic_state *state) |
| { |
| struct drm_device *drm = plane->dev; |
| struct ssd130x_device *ssd130x = drm_to_ssd130x(drm); |
| struct drm_plane_state *plane_state = drm_atomic_get_new_plane_state(state, plane); |
| struct ssd130x_plane_state *ssd130x_state = to_ssd130x_plane_state(plane_state); |
| struct drm_shadow_plane_state *shadow_plane_state = &ssd130x_state->base; |
| struct drm_crtc *crtc = plane_state->crtc; |
| struct drm_crtc_state *crtc_state = NULL; |
| const struct drm_format_info *fi; |
| unsigned int pitch; |
| int ret; |
| |
| if (crtc) |
| crtc_state = drm_atomic_get_new_crtc_state(state, crtc); |
| |
| ret = drm_atomic_helper_check_plane_state(plane_state, crtc_state, |
| DRM_PLANE_NO_SCALING, |
| DRM_PLANE_NO_SCALING, |
| false, false); |
| if (ret) |
| return ret; |
| else if (!plane_state->visible) |
| return 0; |
| |
| fi = drm_format_info(DRM_FORMAT_R1); |
| if (!fi) |
| return -EINVAL; |
| |
| pitch = drm_format_info_min_pitch(fi, 0, ssd130x->width); |
| |
| if (plane_state->fb->format != fi) { |
| void *buf; |
| |
| /* format conversion necessary; reserve buffer */ |
| buf = drm_format_conv_state_reserve(&shadow_plane_state->fmtcnv_state, |
| pitch, GFP_KERNEL); |
| if (!buf) |
| return -ENOMEM; |
| } |
| |
| ssd130x_state->buffer = kcalloc(pitch, ssd130x->height, GFP_KERNEL); |
| if (!ssd130x_state->buffer) |
| return -ENOMEM; |
| |
| return 0; |
| } |
| |
| static int ssd132x_primary_plane_atomic_check(struct drm_plane *plane, |
| struct drm_atomic_state *state) |
| { |
| struct drm_device *drm = plane->dev; |
| struct ssd130x_device *ssd130x = drm_to_ssd130x(drm); |
| struct drm_plane_state *plane_state = drm_atomic_get_new_plane_state(state, plane); |
| struct ssd130x_plane_state *ssd130x_state = to_ssd130x_plane_state(plane_state); |
| struct drm_shadow_plane_state *shadow_plane_state = &ssd130x_state->base; |
| struct drm_crtc *crtc = plane_state->crtc; |
| struct drm_crtc_state *crtc_state = NULL; |
| const struct drm_format_info *fi; |
| unsigned int pitch; |
| int ret; |
| |
| if (crtc) |
| crtc_state = drm_atomic_get_new_crtc_state(state, crtc); |
| |
| ret = drm_atomic_helper_check_plane_state(plane_state, crtc_state, |
| DRM_PLANE_NO_SCALING, |
| DRM_PLANE_NO_SCALING, |
| false, false); |
| if (ret) |
| return ret; |
| else if (!plane_state->visible) |
| return 0; |
| |
| fi = drm_format_info(DRM_FORMAT_R8); |
| if (!fi) |
| return -EINVAL; |
| |
| pitch = drm_format_info_min_pitch(fi, 0, ssd130x->width); |
| |
| if (plane_state->fb->format != fi) { |
| void *buf; |
| |
| /* format conversion necessary; reserve buffer */ |
| buf = drm_format_conv_state_reserve(&shadow_plane_state->fmtcnv_state, |
| pitch, GFP_KERNEL); |
| if (!buf) |
| return -ENOMEM; |
| } |
| |
| ssd130x_state->buffer = kcalloc(pitch, ssd130x->height, GFP_KERNEL); |
| if (!ssd130x_state->buffer) |
| return -ENOMEM; |
| |
| return 0; |
| } |
| |
| static int ssd133x_primary_plane_atomic_check(struct drm_plane *plane, |
| struct drm_atomic_state *state) |
| { |
| struct drm_plane_state *plane_state = drm_atomic_get_new_plane_state(state, plane); |
| struct drm_crtc *crtc = plane_state->crtc; |
| struct drm_crtc_state *crtc_state = NULL; |
| int ret; |
| |
| if (crtc) |
| crtc_state = drm_atomic_get_new_crtc_state(state, crtc); |
| |
| ret = drm_atomic_helper_check_plane_state(plane_state, crtc_state, |
| DRM_PLANE_NO_SCALING, |
| DRM_PLANE_NO_SCALING, |
| false, false); |
| if (ret) |
| return ret; |
| else if (!plane_state->visible) |
| return 0; |
| |
| return 0; |
| } |
| |
| static void ssd130x_primary_plane_atomic_update(struct drm_plane *plane, |
| struct drm_atomic_state *state) |
| { |
| struct drm_plane_state *plane_state = drm_atomic_get_new_plane_state(state, plane); |
| struct drm_plane_state *old_plane_state = drm_atomic_get_old_plane_state(state, plane); |
| struct drm_shadow_plane_state *shadow_plane_state = to_drm_shadow_plane_state(plane_state); |
| struct drm_crtc_state *crtc_state = drm_atomic_get_new_crtc_state(state, plane_state->crtc); |
| struct ssd130x_crtc_state *ssd130x_crtc_state = to_ssd130x_crtc_state(crtc_state); |
| struct ssd130x_plane_state *ssd130x_plane_state = to_ssd130x_plane_state(plane_state); |
| struct drm_framebuffer *fb = plane_state->fb; |
| struct drm_atomic_helper_damage_iter iter; |
| struct drm_device *drm = plane->dev; |
| struct drm_rect dst_clip; |
| struct drm_rect damage; |
| int idx; |
| |
| if (!drm_dev_enter(drm, &idx)) |
| return; |
| |
| drm_atomic_helper_damage_iter_init(&iter, old_plane_state, plane_state); |
| drm_atomic_for_each_plane_damage(&iter, &damage) { |
| dst_clip = plane_state->dst; |
| |
| if (!drm_rect_intersect(&dst_clip, &damage)) |
| continue; |
| |
| ssd130x_fb_blit_rect(fb, &shadow_plane_state->data[0], &dst_clip, |
| ssd130x_plane_state->buffer, |
| ssd130x_crtc_state->data_array, |
| &shadow_plane_state->fmtcnv_state); |
| } |
| |
| drm_dev_exit(idx); |
| } |
| |
| static void ssd132x_primary_plane_atomic_update(struct drm_plane *plane, |
| struct drm_atomic_state *state) |
| { |
| struct drm_plane_state *plane_state = drm_atomic_get_new_plane_state(state, plane); |
| struct drm_plane_state *old_plane_state = drm_atomic_get_old_plane_state(state, plane); |
| struct drm_shadow_plane_state *shadow_plane_state = to_drm_shadow_plane_state(plane_state); |
| struct drm_crtc_state *crtc_state = drm_atomic_get_new_crtc_state(state, plane_state->crtc); |
| struct ssd130x_crtc_state *ssd130x_crtc_state = to_ssd130x_crtc_state(crtc_state); |
| struct ssd130x_plane_state *ssd130x_plane_state = to_ssd130x_plane_state(plane_state); |
| struct drm_framebuffer *fb = plane_state->fb; |
| struct drm_atomic_helper_damage_iter iter; |
| struct drm_device *drm = plane->dev; |
| struct drm_rect dst_clip; |
| struct drm_rect damage; |
| int idx; |
| |
| if (!drm_dev_enter(drm, &idx)) |
| return; |
| |
| drm_atomic_helper_damage_iter_init(&iter, old_plane_state, plane_state); |
| drm_atomic_for_each_plane_damage(&iter, &damage) { |
| dst_clip = plane_state->dst; |
| |
| if (!drm_rect_intersect(&dst_clip, &damage)) |
| continue; |
| |
| ssd132x_fb_blit_rect(fb, &shadow_plane_state->data[0], &dst_clip, |
| ssd130x_plane_state->buffer, |
| ssd130x_crtc_state->data_array, |
| &shadow_plane_state->fmtcnv_state); |
| } |
| |
| drm_dev_exit(idx); |
| } |
| |
| static void ssd133x_primary_plane_atomic_update(struct drm_plane *plane, |
| struct drm_atomic_state *state) |
| { |
| struct drm_plane_state *plane_state = drm_atomic_get_new_plane_state(state, plane); |
| struct drm_plane_state *old_plane_state = drm_atomic_get_old_plane_state(state, plane); |
| struct drm_shadow_plane_state *shadow_plane_state = to_drm_shadow_plane_state(plane_state); |
| struct drm_crtc_state *crtc_state = drm_atomic_get_new_crtc_state(state, plane_state->crtc); |
| struct ssd130x_crtc_state *ssd130x_crtc_state = to_ssd130x_crtc_state(crtc_state); |
| struct drm_framebuffer *fb = plane_state->fb; |
| struct drm_atomic_helper_damage_iter iter; |
| struct drm_device *drm = plane->dev; |
| struct drm_rect dst_clip; |
| struct drm_rect damage; |
| int idx; |
| |
| if (!drm_dev_enter(drm, &idx)) |
| return; |
| |
| drm_atomic_helper_damage_iter_init(&iter, old_plane_state, plane_state); |
| drm_atomic_for_each_plane_damage(&iter, &damage) { |
| dst_clip = plane_state->dst; |
| |
| if (!drm_rect_intersect(&dst_clip, &damage)) |
| continue; |
| |
| ssd133x_fb_blit_rect(fb, &shadow_plane_state->data[0], &dst_clip, |
| ssd130x_crtc_state->data_array, |
| &shadow_plane_state->fmtcnv_state); |
| } |
| |
| drm_dev_exit(idx); |
| } |
| |
| static void ssd130x_primary_plane_atomic_disable(struct drm_plane *plane, |
| struct drm_atomic_state *state) |
| { |
| struct drm_device *drm = plane->dev; |
| struct ssd130x_device *ssd130x = drm_to_ssd130x(drm); |
| struct drm_plane_state *plane_state = drm_atomic_get_new_plane_state(state, plane); |
| struct drm_crtc_state *crtc_state; |
| struct ssd130x_crtc_state *ssd130x_crtc_state; |
| int idx; |
| |
| if (!plane_state->crtc) |
| return; |
| |
| crtc_state = drm_atomic_get_new_crtc_state(state, plane_state->crtc); |
| ssd130x_crtc_state = to_ssd130x_crtc_state(crtc_state); |
| |
| if (!drm_dev_enter(drm, &idx)) |
| return; |
| |
| ssd130x_clear_screen(ssd130x, ssd130x_crtc_state->data_array); |
| |
| drm_dev_exit(idx); |
| } |
| |
| static void ssd132x_primary_plane_atomic_disable(struct drm_plane *plane, |
| struct drm_atomic_state *state) |
| { |
| struct drm_device *drm = plane->dev; |
| struct ssd130x_device *ssd130x = drm_to_ssd130x(drm); |
| struct drm_plane_state *plane_state = drm_atomic_get_new_plane_state(state, plane); |
| struct drm_crtc_state *crtc_state; |
| struct ssd130x_crtc_state *ssd130x_crtc_state; |
| int idx; |
| |
| if (!plane_state->crtc) |
| return; |
| |
| crtc_state = drm_atomic_get_new_crtc_state(state, plane_state->crtc); |
| ssd130x_crtc_state = to_ssd130x_crtc_state(crtc_state); |
| |
| if (!drm_dev_enter(drm, &idx)) |
| return; |
| |
| ssd132x_clear_screen(ssd130x, ssd130x_crtc_state->data_array); |
| |
| drm_dev_exit(idx); |
| } |
| |
| static void ssd133x_primary_plane_atomic_disable(struct drm_plane *plane, |
| struct drm_atomic_state *state) |
| { |
| struct drm_device *drm = plane->dev; |
| struct ssd130x_device *ssd130x = drm_to_ssd130x(drm); |
| struct drm_plane_state *plane_state = drm_atomic_get_new_plane_state(state, plane); |
| struct drm_crtc_state *crtc_state; |
| struct ssd130x_crtc_state *ssd130x_crtc_state; |
| int idx; |
| |
| if (!plane_state->crtc) |
| return; |
| |
| crtc_state = drm_atomic_get_new_crtc_state(state, plane_state->crtc); |
| ssd130x_crtc_state = to_ssd130x_crtc_state(crtc_state); |
| |
| if (!drm_dev_enter(drm, &idx)) |
| return; |
| |
| ssd133x_clear_screen(ssd130x, ssd130x_crtc_state->data_array); |
| |
| drm_dev_exit(idx); |
| } |
| |
| /* Called during init to allocate the plane's atomic state. */ |
| static void ssd130x_primary_plane_reset(struct drm_plane *plane) |
| { |
| struct ssd130x_plane_state *ssd130x_state; |
| |
| WARN_ON(plane->state); |
| |
| ssd130x_state = kzalloc(sizeof(*ssd130x_state), GFP_KERNEL); |
| if (!ssd130x_state) |
| return; |
| |
| __drm_gem_reset_shadow_plane(plane, &ssd130x_state->base); |
| } |
| |
| static struct drm_plane_state *ssd130x_primary_plane_duplicate_state(struct drm_plane *plane) |
| { |
| struct drm_shadow_plane_state *new_shadow_plane_state; |
| struct ssd130x_plane_state *old_ssd130x_state; |
| struct ssd130x_plane_state *ssd130x_state; |
| |
| if (WARN_ON(!plane->state)) |
| return NULL; |
| |
| old_ssd130x_state = to_ssd130x_plane_state(plane->state); |
| ssd130x_state = kmemdup(old_ssd130x_state, sizeof(*ssd130x_state), GFP_KERNEL); |
| if (!ssd130x_state) |
| return NULL; |
| |
| /* The buffer is not duplicated and is allocated in .atomic_check */ |
| ssd130x_state->buffer = NULL; |
| |
| new_shadow_plane_state = &ssd130x_state->base; |
| |
| __drm_gem_duplicate_shadow_plane_state(plane, new_shadow_plane_state); |
| |
| return &new_shadow_plane_state->base; |
| } |
| |
| static void ssd130x_primary_plane_destroy_state(struct drm_plane *plane, |
| struct drm_plane_state *state) |
| { |
| struct ssd130x_plane_state *ssd130x_state = to_ssd130x_plane_state(state); |
| |
| kfree(ssd130x_state->buffer); |
| |
| __drm_gem_destroy_shadow_plane_state(&ssd130x_state->base); |
| |
| kfree(ssd130x_state); |
| } |
| |
| static const struct drm_plane_helper_funcs ssd130x_primary_plane_helper_funcs[] = { |
| [SSD130X_FAMILY] = { |
| DRM_GEM_SHADOW_PLANE_HELPER_FUNCS, |
| .atomic_check = ssd130x_primary_plane_atomic_check, |
| .atomic_update = ssd130x_primary_plane_atomic_update, |
| .atomic_disable = ssd130x_primary_plane_atomic_disable, |
| }, |
| [SSD132X_FAMILY] = { |
| DRM_GEM_SHADOW_PLANE_HELPER_FUNCS, |
| .atomic_check = ssd132x_primary_plane_atomic_check, |
| .atomic_update = ssd132x_primary_plane_atomic_update, |
| .atomic_disable = ssd132x_primary_plane_atomic_disable, |
| }, |
| [SSD133X_FAMILY] = { |
| DRM_GEM_SHADOW_PLANE_HELPER_FUNCS, |
| .atomic_check = ssd133x_primary_plane_atomic_check, |
| .atomic_update = ssd133x_primary_plane_atomic_update, |
| .atomic_disable = ssd133x_primary_plane_atomic_disable, |
| } |
| }; |
| |
| static const struct drm_plane_funcs ssd130x_primary_plane_funcs = { |
| .update_plane = drm_atomic_helper_update_plane, |
| .disable_plane = drm_atomic_helper_disable_plane, |
| .reset = ssd130x_primary_plane_reset, |
| .atomic_duplicate_state = ssd130x_primary_plane_duplicate_state, |
| .atomic_destroy_state = ssd130x_primary_plane_destroy_state, |
| .destroy = drm_plane_cleanup, |
| }; |
| |
| static enum drm_mode_status ssd130x_crtc_mode_valid(struct drm_crtc *crtc, |
| const struct drm_display_mode *mode) |
| { |
| struct ssd130x_device *ssd130x = drm_to_ssd130x(crtc->dev); |
| |
| if (mode->hdisplay != ssd130x->mode.hdisplay && |
| mode->vdisplay != ssd130x->mode.vdisplay) |
| return MODE_ONE_SIZE; |
| else if (mode->hdisplay != ssd130x->mode.hdisplay) |
| return MODE_ONE_WIDTH; |
| else if (mode->vdisplay != ssd130x->mode.vdisplay) |
| return MODE_ONE_HEIGHT; |
| |
| return MODE_OK; |
| } |
| |
| static int ssd130x_crtc_atomic_check(struct drm_crtc *crtc, |
| struct drm_atomic_state *state) |
| { |
| struct drm_device *drm = crtc->dev; |
| struct ssd130x_device *ssd130x = drm_to_ssd130x(drm); |
| struct drm_crtc_state *crtc_state = drm_atomic_get_new_crtc_state(state, crtc); |
| struct ssd130x_crtc_state *ssd130x_state = to_ssd130x_crtc_state(crtc_state); |
| unsigned int pages = DIV_ROUND_UP(ssd130x->height, SSD130X_PAGE_HEIGHT); |
| int ret; |
| |
| ret = drm_crtc_helper_atomic_check(crtc, state); |
| if (ret) |
| return ret; |
| |
| ssd130x_state->data_array = kmalloc(ssd130x->width * pages, GFP_KERNEL); |
| if (!ssd130x_state->data_array) |
| return -ENOMEM; |
| |
| return 0; |
| } |
| |
| static int ssd132x_crtc_atomic_check(struct drm_crtc *crtc, |
| struct drm_atomic_state *state) |
| { |
| struct drm_device *drm = crtc->dev; |
| struct ssd130x_device *ssd130x = drm_to_ssd130x(drm); |
| struct drm_crtc_state *crtc_state = drm_atomic_get_new_crtc_state(state, crtc); |
| struct ssd130x_crtc_state *ssd130x_state = to_ssd130x_crtc_state(crtc_state); |
| unsigned int columns = DIV_ROUND_UP(ssd130x->width, SSD132X_SEGMENT_WIDTH); |
| int ret; |
| |
| ret = drm_crtc_helper_atomic_check(crtc, state); |
| if (ret) |
| return ret; |
| |
| ssd130x_state->data_array = kmalloc(columns * ssd130x->height, GFP_KERNEL); |
| if (!ssd130x_state->data_array) |
| return -ENOMEM; |
| |
| return 0; |
| } |
| |
| static int ssd133x_crtc_atomic_check(struct drm_crtc *crtc, |
| struct drm_atomic_state *state) |
| { |
| struct drm_device *drm = crtc->dev; |
| struct ssd130x_device *ssd130x = drm_to_ssd130x(drm); |
| struct drm_crtc_state *crtc_state = drm_atomic_get_new_crtc_state(state, crtc); |
| struct ssd130x_crtc_state *ssd130x_state = to_ssd130x_crtc_state(crtc_state); |
| const struct drm_format_info *fi = drm_format_info(DRM_FORMAT_RGB332); |
| unsigned int pitch; |
| int ret; |
| |
| if (!fi) |
| return -EINVAL; |
| |
| ret = drm_crtc_helper_atomic_check(crtc, state); |
| if (ret) |
| return ret; |
| |
| pitch = drm_format_info_min_pitch(fi, 0, ssd130x->width); |
| |
| ssd130x_state->data_array = kmalloc(pitch * ssd130x->height, GFP_KERNEL); |
| if (!ssd130x_state->data_array) |
| return -ENOMEM; |
| |
| return 0; |
| } |
| |
| /* Called during init to allocate the CRTC's atomic state. */ |
| static void ssd130x_crtc_reset(struct drm_crtc *crtc) |
| { |
| struct ssd130x_crtc_state *ssd130x_state; |
| |
| WARN_ON(crtc->state); |
| |
| ssd130x_state = kzalloc(sizeof(*ssd130x_state), GFP_KERNEL); |
| if (!ssd130x_state) |
| return; |
| |
| __drm_atomic_helper_crtc_reset(crtc, &ssd130x_state->base); |
| } |
| |
| static struct drm_crtc_state *ssd130x_crtc_duplicate_state(struct drm_crtc *crtc) |
| { |
| struct ssd130x_crtc_state *old_ssd130x_state; |
| struct ssd130x_crtc_state *ssd130x_state; |
| |
| if (WARN_ON(!crtc->state)) |
| return NULL; |
| |
| old_ssd130x_state = to_ssd130x_crtc_state(crtc->state); |
| ssd130x_state = kmemdup(old_ssd130x_state, sizeof(*ssd130x_state), GFP_KERNEL); |
| if (!ssd130x_state) |
| return NULL; |
| |
| /* The buffer is not duplicated and is allocated in .atomic_check */ |
| ssd130x_state->data_array = NULL; |
| |
| __drm_atomic_helper_crtc_duplicate_state(crtc, &ssd130x_state->base); |
| |
| return &ssd130x_state->base; |
| } |
| |
| static void ssd130x_crtc_destroy_state(struct drm_crtc *crtc, |
| struct drm_crtc_state *state) |
| { |
| struct ssd130x_crtc_state *ssd130x_state = to_ssd130x_crtc_state(state); |
| |
| kfree(ssd130x_state->data_array); |
| |
| __drm_atomic_helper_crtc_destroy_state(state); |
| |
| kfree(ssd130x_state); |
| } |
| |
| /* |
| * The CRTC is always enabled. Screen updates are performed by |
| * the primary plane's atomic_update function. Disabling clears |
| * the screen in the primary plane's atomic_disable function. |
| */ |
| static const struct drm_crtc_helper_funcs ssd130x_crtc_helper_funcs[] = { |
| [SSD130X_FAMILY] = { |
| .mode_valid = ssd130x_crtc_mode_valid, |
| .atomic_check = ssd130x_crtc_atomic_check, |
| }, |
| [SSD132X_FAMILY] = { |
| .mode_valid = ssd130x_crtc_mode_valid, |
| .atomic_check = ssd132x_crtc_atomic_check, |
| }, |
| [SSD133X_FAMILY] = { |
| .mode_valid = ssd130x_crtc_mode_valid, |
| .atomic_check = ssd133x_crtc_atomic_check, |
| }, |
| }; |
| |
| static const struct drm_crtc_funcs ssd130x_crtc_funcs = { |
| .reset = ssd130x_crtc_reset, |
| .destroy = drm_crtc_cleanup, |
| .set_config = drm_atomic_helper_set_config, |
| .page_flip = drm_atomic_helper_page_flip, |
| .atomic_duplicate_state = ssd130x_crtc_duplicate_state, |
| .atomic_destroy_state = ssd130x_crtc_destroy_state, |
| }; |
| |
| static void ssd130x_encoder_atomic_enable(struct drm_encoder *encoder, |
| struct drm_atomic_state *state) |
| { |
| struct drm_device *drm = encoder->dev; |
| struct ssd130x_device *ssd130x = drm_to_ssd130x(drm); |
| int ret; |
| |
| ret = ssd130x_power_on(ssd130x); |
| if (ret) |
| return; |
| |
| ret = ssd130x_init(ssd130x); |
| if (ret) |
| goto power_off; |
| |
| ssd130x_write_cmd(ssd130x, 1, SSD13XX_DISPLAY_ON); |
| |
| backlight_enable(ssd130x->bl_dev); |
| |
| return; |
| |
| power_off: |
| ssd130x_power_off(ssd130x); |
| return; |
| } |
| |
| static void ssd132x_encoder_atomic_enable(struct drm_encoder *encoder, |
| struct drm_atomic_state *state) |
| { |
| struct drm_device *drm = encoder->dev; |
| struct ssd130x_device *ssd130x = drm_to_ssd130x(drm); |
| int ret; |
| |
| ret = ssd130x_power_on(ssd130x); |
| if (ret) |
| return; |
| |
| ret = ssd132x_init(ssd130x); |
| if (ret) |
| goto power_off; |
| |
| ssd130x_write_cmd(ssd130x, 1, SSD13XX_DISPLAY_ON); |
| |
| backlight_enable(ssd130x->bl_dev); |
| |
| return; |
| |
| power_off: |
| ssd130x_power_off(ssd130x); |
| } |
| |
| static void ssd133x_encoder_atomic_enable(struct drm_encoder *encoder, |
| struct drm_atomic_state *state) |
| { |
| struct drm_device *drm = encoder->dev; |
| struct ssd130x_device *ssd130x = drm_to_ssd130x(drm); |
| int ret; |
| |
| ret = ssd130x_power_on(ssd130x); |
| if (ret) |
| return; |
| |
| ret = ssd133x_init(ssd130x); |
| if (ret) |
| goto power_off; |
| |
| ssd130x_write_cmd(ssd130x, 1, SSD13XX_DISPLAY_ON); |
| |
| backlight_enable(ssd130x->bl_dev); |
| |
| return; |
| |
| power_off: |
| ssd130x_power_off(ssd130x); |
| } |
| |
| static void ssd130x_encoder_atomic_disable(struct drm_encoder *encoder, |
| struct drm_atomic_state *state) |
| { |
| struct drm_device *drm = encoder->dev; |
| struct ssd130x_device *ssd130x = drm_to_ssd130x(drm); |
| |
| backlight_disable(ssd130x->bl_dev); |
| |
| ssd130x_write_cmd(ssd130x, 1, SSD13XX_DISPLAY_OFF); |
| |
| ssd130x_power_off(ssd130x); |
| } |
| |
| static const struct drm_encoder_helper_funcs ssd130x_encoder_helper_funcs[] = { |
| [SSD130X_FAMILY] = { |
| .atomic_enable = ssd130x_encoder_atomic_enable, |
| .atomic_disable = ssd130x_encoder_atomic_disable, |
| }, |
| [SSD132X_FAMILY] = { |
| .atomic_enable = ssd132x_encoder_atomic_enable, |
| .atomic_disable = ssd130x_encoder_atomic_disable, |
| }, |
| [SSD133X_FAMILY] = { |
| .atomic_enable = ssd133x_encoder_atomic_enable, |
| .atomic_disable = ssd130x_encoder_atomic_disable, |
| } |
| }; |
| |
| static const struct drm_encoder_funcs ssd130x_encoder_funcs = { |
| .destroy = drm_encoder_cleanup, |
| }; |
| |
| static int ssd130x_connector_get_modes(struct drm_connector *connector) |
| { |
| struct ssd130x_device *ssd130x = drm_to_ssd130x(connector->dev); |
| struct drm_display_mode *mode; |
| struct device *dev = ssd130x->dev; |
| |
| mode = drm_mode_duplicate(connector->dev, &ssd130x->mode); |
| if (!mode) { |
| dev_err(dev, "Failed to duplicated mode\n"); |
| return 0; |
| } |
| |
| drm_mode_probed_add(connector, mode); |
| drm_set_preferred_mode(connector, mode->hdisplay, mode->vdisplay); |
| |
| /* There is only a single mode */ |
| return 1; |
| } |
| |
| static const struct drm_connector_helper_funcs ssd130x_connector_helper_funcs = { |
| .get_modes = ssd130x_connector_get_modes, |
| }; |
| |
| static const struct drm_connector_funcs ssd130x_connector_funcs = { |
| .reset = drm_atomic_helper_connector_reset, |
| .fill_modes = drm_helper_probe_single_connector_modes, |
| .destroy = drm_connector_cleanup, |
| .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state, |
| .atomic_destroy_state = drm_atomic_helper_connector_destroy_state, |
| }; |
| |
| static const struct drm_mode_config_funcs ssd130x_mode_config_funcs = { |
| .fb_create = drm_gem_fb_create_with_dirty, |
| .atomic_check = drm_atomic_helper_check, |
| .atomic_commit = drm_atomic_helper_commit, |
| }; |
| |
| static const uint32_t ssd130x_formats[] = { |
| DRM_FORMAT_XRGB8888, |
| }; |
| |
| DEFINE_DRM_GEM_FOPS(ssd130x_fops); |
| |
| static const struct drm_driver ssd130x_drm_driver = { |
| DRM_GEM_SHMEM_DRIVER_OPS, |
| .name = DRIVER_NAME, |
| .desc = DRIVER_DESC, |
| .date = DRIVER_DATE, |
| .major = DRIVER_MAJOR, |
| .minor = DRIVER_MINOR, |
| .driver_features = DRIVER_ATOMIC | DRIVER_GEM | DRIVER_MODESET, |
| .fops = &ssd130x_fops, |
| }; |
| |
| static int ssd130x_update_bl(struct backlight_device *bdev) |
| { |
| struct ssd130x_device *ssd130x = bl_get_data(bdev); |
| int brightness = backlight_get_brightness(bdev); |
| int ret; |
| |
| ssd130x->contrast = brightness; |
| |
| ret = ssd130x_write_cmd(ssd130x, 1, SSD13XX_CONTRAST); |
| if (ret < 0) |
| return ret; |
| |
| ret = ssd130x_write_cmd(ssd130x, 1, ssd130x->contrast); |
| if (ret < 0) |
| return ret; |
| |
| return 0; |
| } |
| |
| static const struct backlight_ops ssd130xfb_bl_ops = { |
| .update_status = ssd130x_update_bl, |
| }; |
| |
| static void ssd130x_parse_properties(struct ssd130x_device *ssd130x) |
| { |
| struct device *dev = ssd130x->dev; |
| |
| if (device_property_read_u32(dev, "solomon,width", &ssd130x->width)) |
| ssd130x->width = ssd130x->device_info->default_width; |
| |
| if (device_property_read_u32(dev, "solomon,height", &ssd130x->height)) |
| ssd130x->height = ssd130x->device_info->default_height; |
| |
| if (device_property_read_u32(dev, "solomon,page-offset", &ssd130x->page_offset)) |
| ssd130x->page_offset = 1; |
| |
| if (device_property_read_u32(dev, "solomon,col-offset", &ssd130x->col_offset)) |
| ssd130x->col_offset = 0; |
| |
| if (device_property_read_u32(dev, "solomon,com-offset", &ssd130x->com_offset)) |
| ssd130x->com_offset = 0; |
| |
| if (device_property_read_u32(dev, "solomon,prechargep1", &ssd130x->prechargep1)) |
| ssd130x->prechargep1 = 2; |
| |
| if (device_property_read_u32(dev, "solomon,prechargep2", &ssd130x->prechargep2)) |
| ssd130x->prechargep2 = 2; |
| |
| if (!device_property_read_u8_array(dev, "solomon,lookup-table", |
| ssd130x->lookup_table, |
| ARRAY_SIZE(ssd130x->lookup_table))) |
| ssd130x->lookup_table_set = 1; |
| |
| ssd130x->seg_remap = !device_property_read_bool(dev, "solomon,segment-no-remap"); |
| ssd130x->com_seq = device_property_read_bool(dev, "solomon,com-seq"); |
| ssd130x->com_lrremap = device_property_read_bool(dev, "solomon,com-lrremap"); |
| ssd130x->com_invdir = device_property_read_bool(dev, "solomon,com-invdir"); |
| ssd130x->area_color_enable = |
| device_property_read_bool(dev, "solomon,area-color-enable"); |
| ssd130x->low_power = device_property_read_bool(dev, "solomon,low-power"); |
| |
| ssd130x->contrast = 127; |
| ssd130x->vcomh = ssd130x->device_info->default_vcomh; |
| |
| /* Setup display timing */ |
| if (device_property_read_u32(dev, "solomon,dclk-div", &ssd130x->dclk_div)) |
| ssd130x->dclk_div = ssd130x->device_info->default_dclk_div; |
| if (device_property_read_u32(dev, "solomon,dclk-frq", &ssd130x->dclk_frq)) |
| ssd130x->dclk_frq = ssd130x->device_info->default_dclk_frq; |
| } |
| |
| static int ssd130x_init_modeset(struct ssd130x_device *ssd130x) |
| { |
| enum ssd130x_family_ids family_id = ssd130x->device_info->family_id; |
| struct drm_display_mode *mode = &ssd130x->mode; |
| struct device *dev = ssd130x->dev; |
| struct drm_device *drm = &ssd130x->drm; |
| unsigned long max_width, max_height; |
| struct drm_plane *primary_plane; |
| struct drm_crtc *crtc; |
| struct drm_encoder *encoder; |
| struct drm_connector *connector; |
| int ret; |
| |
| /* |
| * Modesetting |
| */ |
| |
| ret = drmm_mode_config_init(drm); |
| if (ret) { |
| dev_err(dev, "DRM mode config init failed: %d\n", ret); |
| return ret; |
| } |
| |
| mode->type = DRM_MODE_TYPE_DRIVER; |
| mode->clock = 1; |
| mode->hdisplay = mode->htotal = ssd130x->width; |
| mode->hsync_start = mode->hsync_end = ssd130x->width; |
| mode->vdisplay = mode->vtotal = ssd130x->height; |
| mode->vsync_start = mode->vsync_end = ssd130x->height; |
| mode->width_mm = 27; |
| mode->height_mm = 27; |
| |
| max_width = max_t(unsigned long, mode->hdisplay, DRM_SHADOW_PLANE_MAX_WIDTH); |
| max_height = max_t(unsigned long, mode->vdisplay, DRM_SHADOW_PLANE_MAX_HEIGHT); |
| |
| drm->mode_config.min_width = mode->hdisplay; |
| drm->mode_config.max_width = max_width; |
| drm->mode_config.min_height = mode->vdisplay; |
| drm->mode_config.max_height = max_height; |
| drm->mode_config.preferred_depth = 24; |
| drm->mode_config.funcs = &ssd130x_mode_config_funcs; |
| |
| /* Primary plane */ |
| |
| primary_plane = &ssd130x->primary_plane; |
| ret = drm_universal_plane_init(drm, primary_plane, 0, &ssd130x_primary_plane_funcs, |
| ssd130x_formats, ARRAY_SIZE(ssd130x_formats), |
| NULL, DRM_PLANE_TYPE_PRIMARY, NULL); |
| if (ret) { |
| dev_err(dev, "DRM primary plane init failed: %d\n", ret); |
| return ret; |
| } |
| |
| drm_plane_helper_add(primary_plane, &ssd130x_primary_plane_helper_funcs[family_id]); |
| |
| drm_plane_enable_fb_damage_clips(primary_plane); |
| |
| /* CRTC */ |
| |
| crtc = &ssd130x->crtc; |
| ret = drm_crtc_init_with_planes(drm, crtc, primary_plane, NULL, |
| &ssd130x_crtc_funcs, NULL); |
| if (ret) { |
| dev_err(dev, "DRM crtc init failed: %d\n", ret); |
| return ret; |
| } |
| |
| drm_crtc_helper_add(crtc, &ssd130x_crtc_helper_funcs[family_id]); |
| |
| /* Encoder */ |
| |
| encoder = &ssd130x->encoder; |
| ret = drm_encoder_init(drm, encoder, &ssd130x_encoder_funcs, |
| DRM_MODE_ENCODER_NONE, NULL); |
| if (ret) { |
| dev_err(dev, "DRM encoder init failed: %d\n", ret); |
| return ret; |
| } |
| |
| drm_encoder_helper_add(encoder, &ssd130x_encoder_helper_funcs[family_id]); |
| |
| encoder->possible_crtcs = drm_crtc_mask(crtc); |
| |
| /* Connector */ |
| |
| connector = &ssd130x->connector; |
| ret = drm_connector_init(drm, connector, &ssd130x_connector_funcs, |
| DRM_MODE_CONNECTOR_Unknown); |
| if (ret) { |
| dev_err(dev, "DRM connector init failed: %d\n", ret); |
| return ret; |
| } |
| |
| drm_connector_helper_add(connector, &ssd130x_connector_helper_funcs); |
| |
| ret = drm_connector_attach_encoder(connector, encoder); |
| if (ret) { |
| dev_err(dev, "DRM attach connector to encoder failed: %d\n", ret); |
| return ret; |
| } |
| |
| drm_mode_config_reset(drm); |
| |
| return 0; |
| } |
| |
| static int ssd130x_get_resources(struct ssd130x_device *ssd130x) |
| { |
| struct device *dev = ssd130x->dev; |
| |
| ssd130x->reset = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW); |
| if (IS_ERR(ssd130x->reset)) |
| return dev_err_probe(dev, PTR_ERR(ssd130x->reset), |
| "Failed to get reset gpio\n"); |
| |
| ssd130x->vcc_reg = devm_regulator_get(dev, "vcc"); |
| if (IS_ERR(ssd130x->vcc_reg)) |
| return dev_err_probe(dev, PTR_ERR(ssd130x->vcc_reg), |
| "Failed to get VCC regulator\n"); |
| |
| return 0; |
| } |
| |
| struct ssd130x_device *ssd130x_probe(struct device *dev, struct regmap *regmap) |
| { |
| struct ssd130x_device *ssd130x; |
| struct backlight_device *bl; |
| struct drm_device *drm; |
| int ret; |
| |
| ssd130x = devm_drm_dev_alloc(dev, &ssd130x_drm_driver, |
| struct ssd130x_device, drm); |
| if (IS_ERR(ssd130x)) |
| return ERR_PTR(dev_err_probe(dev, PTR_ERR(ssd130x), |
| "Failed to allocate DRM device\n")); |
| |
| drm = &ssd130x->drm; |
| |
| ssd130x->dev = dev; |
| ssd130x->regmap = regmap; |
| ssd130x->device_info = device_get_match_data(dev); |
| |
| if (ssd130x->device_info->page_mode_only) |
| ssd130x->page_address_mode = 1; |
| |
| ssd130x_parse_properties(ssd130x); |
| |
| ret = ssd130x_get_resources(ssd130x); |
| if (ret) |
| return ERR_PTR(ret); |
| |
| bl = devm_backlight_device_register(dev, dev_name(dev), dev, ssd130x, |
| &ssd130xfb_bl_ops, NULL); |
| if (IS_ERR(bl)) |
| return ERR_PTR(dev_err_probe(dev, PTR_ERR(bl), |
| "Unable to register backlight device\n")); |
| |
| bl->props.brightness = ssd130x->contrast; |
| bl->props.max_brightness = MAX_CONTRAST; |
| ssd130x->bl_dev = bl; |
| |
| ret = ssd130x_init_modeset(ssd130x); |
| if (ret) |
| return ERR_PTR(ret); |
| |
| ret = drm_dev_register(drm, 0); |
| if (ret) |
| return ERR_PTR(dev_err_probe(dev, ret, "DRM device register failed\n")); |
| |
| drm_fbdev_shmem_setup(drm, 32); |
| |
| return ssd130x; |
| } |
| EXPORT_SYMBOL_GPL(ssd130x_probe); |
| |
| void ssd130x_remove(struct ssd130x_device *ssd130x) |
| { |
| drm_dev_unplug(&ssd130x->drm); |
| drm_atomic_helper_shutdown(&ssd130x->drm); |
| } |
| EXPORT_SYMBOL_GPL(ssd130x_remove); |
| |
| void ssd130x_shutdown(struct ssd130x_device *ssd130x) |
| { |
| drm_atomic_helper_shutdown(&ssd130x->drm); |
| } |
| EXPORT_SYMBOL_GPL(ssd130x_shutdown); |
| |
| MODULE_DESCRIPTION(DRIVER_DESC); |
| MODULE_AUTHOR("Javier Martinez Canillas <javierm@redhat.com>"); |
| MODULE_LICENSE("GPL v2"); |