| # SPDX-License-Identifier: GPL-2.0-only |
| |
| # |
| # Light sensors |
| # |
| # When adding new entries keep the list in alphabetical order |
| |
| menu "Light sensors" |
| |
| config ACPI_ALS |
| tristate "ACPI Ambient Light Sensor" |
| depends on ACPI |
| select IIO_BUFFER |
| select IIO_TRIGGERED_BUFFER |
| select IIO_KFIFO_BUF |
| help |
| Say Y here if you want to build a driver for the ACPI0008 |
| Ambient Light Sensor. |
| |
| To compile this driver as a module, choose M here: the module will |
| be called acpi-als. |
| |
| config ADJD_S311 |
| tristate "ADJD-S311-CR999 digital color sensor" |
| select IIO_BUFFER |
| select IIO_TRIGGERED_BUFFER |
| depends on I2C |
| help |
| If you say yes here you get support for the Avago ADJD-S311-CR999 |
| digital color light sensor. |
| |
| This driver can also be built as a module. If so, the module |
| will be called adjd_s311. |
| |
| config ADUX1020 |
| tristate "ADUX1020 photometric sensor" |
| select REGMAP_I2C |
| depends on I2C |
| help |
| Say Y here if you want to build a driver for the Analog Devices |
| ADUX1020 photometric sensor. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called adux1020. |
| |
| config AL3010 |
| tristate "AL3010 ambient light sensor" |
| depends on I2C |
| help |
| Say Y here if you want to build a driver for the Dyna Image AL3010 |
| ambient light sensor. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called al3010. |
| |
| config AL3320A |
| tristate "AL3320A ambient light sensor" |
| depends on I2C |
| help |
| Say Y here if you want to build a driver for the Dyna Image AL3320A |
| ambient light sensor. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called al3320a. |
| |
| config APDS9300 |
| tristate "APDS9300 ambient light sensor" |
| depends on I2C |
| help |
| Say Y here if you want to build a driver for the Avago APDS9300 |
| ambient light sensor. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called apds9300. |
| |
| config APDS9306 |
| tristate "Avago APDS9306 Ambient Light Sensor" |
| depends on I2C |
| select REGMAP_I2C |
| select IIO_GTS_HELPER |
| help |
| If you say Y or M here, you get support for Avago APDS9306 |
| Ambient Light Sensor. |
| |
| If built as a dynamically linked module, it will be called |
| apds9306. |
| |
| config APDS9960 |
| tristate "Avago APDS9960 gesture/RGB/ALS/proximity sensor" |
| select REGMAP_I2C |
| select IIO_BUFFER |
| select IIO_KFIFO_BUF |
| depends on I2C |
| help |
| Say Y here to build I2C interface support for the Avago |
| APDS9960 gesture/RGB/ALS/proximity sensor. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called apds9960 |
| |
| config AS73211 |
| tristate "AMS AS73211 XYZ color sensor and AMS AS7331 UV sensor" |
| depends on I2C |
| select IIO_BUFFER |
| select IIO_TRIGGERED_BUFFER |
| help |
| If you say yes here you get support for the AMS AS73211 |
| JENCOLOR(R) Digital XYZ and the AMS AS7331 UVA, UVB and UVC |
| ultraviolet sensors. |
| |
| For triggered measurements, you will need an additional trigger driver |
| like IIO_HRTIMER_TRIGGER or IIO_SYSFS_TRIGGER. |
| |
| This driver can also be built as a module. If so, the module |
| will be called as73211. |
| |
| config BH1745 |
| tristate "ROHM BH1745 colour sensor" |
| depends on I2C |
| select REGMAP_I2C |
| select IIO_BUFFER |
| select IIO_TRIGGERED_BUFFER |
| select IIO_GTS_HELPER |
| help |
| Say Y here to build support for the ROHM bh1745 colour sensor. |
| |
| To compile this driver as a module, choose M here: the module will |
| be called bh1745. |
| |
| config BH1750 |
| tristate "ROHM BH1750 ambient light sensor" |
| depends on I2C |
| help |
| Say Y here to build support for the ROHM BH1710, BH1715, BH1721, |
| BH1750, BH1751 ambient light sensors. |
| |
| To compile this driver as a module, choose M here: the module will |
| be called bh1750. |
| |
| config BH1780 |
| tristate "ROHM BH1780 ambient light sensor" |
| depends on I2C |
| help |
| Say Y here to build support for the ROHM BH1780GLI ambient |
| light sensor. |
| |
| To compile this driver as a module, choose M here: the module will |
| be called bh1780. |
| |
| config CM32181 |
| depends on I2C |
| tristate "CM32181 driver" |
| help |
| Say Y here if you use cm32181. |
| This option enables ambient light sensor using |
| Capella cm32181 device driver. |
| |
| To compile this driver as a module, choose M here: |
| the module will be called cm32181. |
| |
| config CM3232 |
| depends on I2C |
| tristate "CM3232 ambient light sensor" |
| help |
| Say Y here if you use cm3232. |
| This option enables ambient light sensor using |
| Capella Microsystems cm3232 device driver. |
| |
| To compile this driver as a module, choose M here: |
| the module will be called cm3232. |
| |
| config CM3323 |
| depends on I2C |
| tristate "Capella CM3323 color light sensor" |
| help |
| Say Y here if you want to build a driver for Capella CM3323 |
| color sensor. |
| |
| To compile this driver as a module, choose M here: the module will |
| be called cm3323. |
| |
| config CM3605 |
| tristate "Capella CM3605 ambient light and proximity sensor" |
| help |
| Say Y here if you want to build a driver for Capella CM3605 |
| ambient light and short range proximity sensor. |
| |
| To compile this driver as a module, choose M here: the module will |
| be called cm3605. |
| |
| config CM36651 |
| depends on I2C |
| tristate "CM36651 driver" |
| help |
| Say Y here if you use cm36651. |
| This option enables proximity & RGB sensor using |
| Capella cm36651 device driver. |
| |
| To compile this driver as a module, choose M here: |
| the module will be called cm36651. |
| |
| config IIO_CROS_EC_LIGHT_PROX |
| tristate "ChromeOS EC Light and Proximity Sensors" |
| depends on IIO_CROS_EC_SENSORS_CORE |
| help |
| Say Y here if you use the light and proximity sensors |
| presented by the ChromeOS EC Sensor hub. |
| |
| To compile this driver as a module, choose M here: |
| the module will be called cros_ec_light_prox. |
| |
| config GP2AP002 |
| tristate "Sharp GP2AP002 Proximity/ALS sensor" |
| depends on I2C |
| select REGMAP |
| help |
| Say Y here if you have a Sharp GP2AP002 proximity/ALS combo-chip |
| hooked to an I2C bus. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called gp2ap002. |
| |
| config GP2AP020A00F |
| tristate "Sharp GP2AP020A00F Proximity/ALS sensor" |
| depends on I2C |
| select REGMAP_I2C |
| select IIO_BUFFER |
| select IIO_TRIGGERED_BUFFER |
| select IRQ_WORK |
| help |
| Say Y here if you have a Sharp GP2AP020A00F proximity/ALS combo-chip |
| hooked to an I2C bus. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called gp2ap020a00f. |
| |
| config IQS621_ALS |
| tristate "Azoteq IQS621/622 ambient light sensors" |
| depends on MFD_IQS62X || COMPILE_TEST |
| help |
| Say Y here if you want to build support for the Azoteq IQS621 |
| and IQS622 ambient light sensors. |
| |
| To compile this driver as a module, choose M here: the module |
| will be called iqs621-als. |
| |
| config SENSORS_ISL29018 |
| tristate "Intersil 29018 light and proximity sensor" |
| depends on I2C |
| select REGMAP_I2C |
| default n |
| help |
| If you say yes here you get support for ambient light sensing and |
| proximity infrared sensing from Intersil ISL29018. |
| This driver will provide the measurements of ambient light intensity |
| in lux, proximity infrared sensing and normal infrared sensing. |
| Data from sensor is accessible via sysfs. |
| |
| config SENSORS_ISL29028 |
| tristate "Intersil ISL29028 Concurrent Light and Proximity Sensor" |
| depends on I2C |
| select REGMAP_I2C |
| help |
| Provides driver for the Intersil's ISL29028 device. |
| This driver supports the sysfs interface to get the ALS, IR intensity, |
| Proximity value via iio. The ISL29028 provides the concurrent sensing |
| of ambient light and proximity. |
| |
| config ISL29125 |
| tristate "Intersil ISL29125 digital color light sensor" |
| depends on I2C |
| select IIO_BUFFER |
| select IIO_TRIGGERED_BUFFER |
| help |
| Say Y here if you want to build a driver for the Intersil ISL29125 |
| RGB light sensor for I2C. |
| |
| To compile this driver as a module, choose M here: the module will be |
| called isl29125. |
| |
| config ISL76682 |
| tristate "Intersil ISL76682 Light Sensor" |
| depends on I2C |
| select REGMAP_I2C |
| help |
| Say Y here if you want to build a driver for the Intersil ISL76682 |
| Ambient Light Sensor and IR Intensity sensor. This driver provides |
| the readouts via standard IIO sysfs and device interface. Both ALS |
| illuminance and IR illuminance are provided raw with separate scale |
| setting which can be configured via sysfs, the default scale is 1000 |
| lux, other options are 4000/16000/64000 lux. |
| |
| To compile this driver as a module, choose M here: the module will be |
| called isl76682. |
| |
| config HID_SENSOR_ALS |
| depends on HID_SENSOR_HUB |
| select IIO_BUFFER |
| select HID_SENSOR_IIO_COMMON |
| select HID_SENSOR_IIO_TRIGGER |
| tristate "HID ALS" |
| help |
| Say yes here to build support for the HID SENSOR |
| Ambient light sensor. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called hid-sensor-als. |
| |
| config HID_SENSOR_PROX |
| depends on HID_SENSOR_HUB |
| select IIO_BUFFER |
| select HID_SENSOR_IIO_COMMON |
| select HID_SENSOR_IIO_TRIGGER |
| tristate "HID PROX" |
| help |
| Say yes here to build support for the HID SENSOR |
| Proximity sensor. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called hid-sensor-prox. |
| |
| config JSA1212 |
| tristate "JSA1212 ALS and proximity sensor driver" |
| depends on I2C |
| select REGMAP_I2C |
| help |
| Say Y here if you want to build a IIO driver for JSA1212 |
| proximity & ALS sensor device. |
| |
| To compile this driver as a module, choose M here: |
| the module will be called jsa1212. |
| |
| config ROHM_BU27008 |
| tristate "ROHM BU27008 color (RGB+C/IR) sensor" |
| depends on I2C |
| select REGMAP_I2C |
| select IIO_GTS_HELPER |
| select IIO_BUFFER |
| select IIO_TRIGGERED_BUFFER |
| help |
| Enable support for the ROHM BU27008 color sensor. |
| The ROHM BU27008 is a sensor with 5 photodiodes (red, green, |
| blue, clear and IR) with four configurable channels. Red and |
| green being always available and two out of the rest three |
| (blue, clear, IR) can be selected to be simultaneously measured. |
| Typical application is adjusting LCD backlight of TVs, |
| mobile phones and tablet PCs. |
| |
| config ROHM_BU27034 |
| tristate "ROHM BU27034 ambient light sensor" |
| depends on I2C |
| select REGMAP_I2C |
| select IIO_GTS_HELPER |
| select IIO_BUFFER |
| select IIO_KFIFO_BUF |
| help |
| Enable support for the ROHM BU27034 ambient light sensor. ROHM BU27034 |
| is an ambient light sesnor with 3 channels and 3 photo diodes capable |
| of detecting a very wide range of illuminance. |
| Typical application is adjusting LCD and backlight power of TVs and |
| mobile phones. |
| |
| config RPR0521 |
| tristate "ROHM RPR0521 ALS and proximity sensor driver" |
| depends on I2C |
| select REGMAP_I2C |
| select IIO_BUFFER |
| select IIO_TRIGGERED_BUFFER |
| help |
| Say Y here if you want to build support for ROHM's RPR0521 |
| ambient light and proximity sensor device. |
| |
| To compile this driver as a module, choose M here: |
| the module will be called rpr0521. |
| |
| config SENSORS_LM3533 |
| tristate "LM3533 ambient light sensor" |
| depends on MFD_LM3533 |
| help |
| If you say yes here you get support for the ambient light sensor |
| interface on National Semiconductor / TI LM3533 Lighting Power |
| chips. |
| |
| The sensor interface can be used to control the LEDs and backlights |
| of the chip through defining five light zones and three sets of |
| corresponding output-current values. |
| |
| The driver provides raw and mean adc readings along with the current |
| light zone through sysfs. A threshold event can be generated on zone |
| changes. The ALS-control output values can be set per zone for the |
| three current output channels. |
| |
| config LTR390 |
| tristate "LTR-390UV-01 ambient light and UV sensor" |
| depends on I2C |
| select REGMAP_I2C |
| help |
| If you say yes here you get support for the Lite-On LTR-390UV-01 |
| ambient light and UV sensor. |
| |
| This driver can also be built as a module. If so, the module |
| will be called ltr390. |
| |
| config LTR501 |
| tristate "LTR-501ALS-01 light sensor" |
| depends on I2C |
| select REGMAP_I2C |
| select IIO_BUFFER |
| select IIO_TRIGGERED_BUFFER |
| help |
| If you say yes here you get support for the Lite-On LTR-501ALS-01 |
| ambient light and proximity sensor. This driver also supports LTR-559 |
| ALS/PS or LTR-301 ALS sensors. |
| |
| This driver can also be built as a module. If so, the module |
| will be called ltr501. |
| |
| config LTRF216A |
| tristate "Liteon LTRF216A Light Sensor" |
| depends on I2C |
| select REGMAP_I2C |
| help |
| If you say Y or M here, you get support for Liteon LTRF216A |
| Ambient Light Sensor. |
| |
| If built as a dynamically linked module, it will be called |
| ltrf216a. |
| |
| config LV0104CS |
| tristate "LV0104CS Ambient Light Sensor" |
| depends on I2C |
| help |
| Say Y here if you want to build support for the On Semiconductor |
| LV0104CS ambient light sensor. |
| |
| To compile this driver as a module, choose M here: |
| the module will be called lv0104cs. |
| |
| config MAX44000 |
| tristate "MAX44000 Ambient and Infrared Proximity Sensor" |
| depends on I2C |
| select REGMAP_I2C |
| select IIO_BUFFER |
| select IIO_TRIGGERED_BUFFER |
| help |
| Say Y here if you want to build support for Maxim Integrated's |
| MAX44000 ambient and infrared proximity sensor device. |
| |
| To compile this driver as a module, choose M here: |
| the module will be called max44000. |
| |
| config MAX44009 |
| tristate "MAX44009 Ambient Light Sensor" |
| depends on I2C |
| select REGMAP_I2C |
| help |
| Say Y here if you want to build support for Maxim Integrated's |
| MAX44009 ambient light sensor device. |
| |
| To compile this driver as a module, choose M here: |
| the module will be called max44009. |
| |
| config NOA1305 |
| tristate "ON Semiconductor NOA1305 ambient light sensor" |
| depends on I2C |
| select REGMAP_I2C |
| help |
| Say Y here if you want to build support for the ON Semiconductor |
| NOA1305 ambient light sensor. |
| |
| To compile this driver as a module, choose M here: |
| The module will be called noa1305. |
| |
| config OPT3001 |
| tristate "Texas Instruments OPT3001 Light Sensor" |
| depends on I2C |
| help |
| If you say Y or M here, you get support for Texas Instruments |
| OPT3001 Ambient Light Sensor. |
| |
| If built as a dynamically linked module, it will be called |
| opt3001. |
| |
| config OPT4001 |
| tristate "Texas Instruments OPT4001 Light Sensor" |
| depends on I2C |
| select REGMAP_I2C |
| help |
| If you say Y or M here, you get support for Texas Instruments |
| OPT4001 Ambient Light Sensor. |
| |
| If built as a dynamically linked module, it will be called |
| opt4001. |
| |
| config PA12203001 |
| tristate "TXC PA12203001 light and proximity sensor" |
| depends on I2C |
| select REGMAP_I2C |
| help |
| If you say yes here you get support for the TXC PA12203001 |
| ambient light and proximity sensor. |
| |
| This driver can also be built as a module. If so, the module |
| will be called pa12203001. |
| |
| config SI1133 |
| tristate "SI1133 UV Index Sensor and Ambient Light Sensor" |
| depends on I2C |
| select REGMAP_I2C |
| help |
| Say Y here if you want to build a driver for the Silicon Labs SI1133 |
| UV Index Sensor and Ambient Light Sensor chip. |
| |
| To compile this driver as a module, choose M here: the module will be |
| called si1133. |
| |
| config SI1145 |
| tristate "SI1132 and SI1141/2/3/5/6/7 combined ALS, UV index and proximity sensor" |
| depends on I2C |
| select IIO_BUFFER |
| select IIO_TRIGGERED_BUFFER |
| help |
| Say Y here if you want to build a driver for the Silicon Labs SI1132 or |
| SI1141/2/3/5/6/7 combined ambient light, UV index and proximity sensor |
| chips. |
| |
| To compile this driver as a module, choose M here: the module will be |
| called si1145. |
| |
| config STK3310 |
| tristate "STK3310 ALS and proximity sensor" |
| depends on I2C |
| select REGMAP_I2C |
| help |
| Say yes here to get support for the Sensortek STK3310 ambient light |
| and proximity sensor. The STK3311 model is also supported by this |
| driver. |
| |
| Choosing M will build the driver as a module. If so, the module |
| will be called stk3310. |
| |
| config ST_UVIS25 |
| tristate "STMicroelectronics UVIS25 sensor driver" |
| depends on (I2C || SPI) |
| select IIO_BUFFER |
| select IIO_TRIGGERED_BUFFER |
| select ST_UVIS25_I2C if (I2C) |
| select ST_UVIS25_SPI if (SPI_MASTER) |
| help |
| Say yes here to build support for STMicroelectronics UVIS25 |
| uv sensor |
| |
| To compile this driver as a module, choose M here: the module |
| will be called st_uvis25. |
| |
| config ST_UVIS25_I2C |
| tristate |
| depends on ST_UVIS25 |
| select REGMAP_I2C |
| |
| config ST_UVIS25_SPI |
| tristate |
| depends on ST_UVIS25 |
| select REGMAP_SPI |
| |
| config TCS3414 |
| tristate "TAOS TCS3414 digital color sensor" |
| depends on I2C |
| select IIO_BUFFER |
| select IIO_TRIGGERED_BUFFER |
| help |
| If you say yes here you get support for the TAOS TCS3414 |
| family of digital color sensors. |
| |
| This driver can also be built as a module. If so, the module |
| will be called tcs3414. |
| |
| config TCS3472 |
| tristate "TAOS TCS3472 color light-to-digital converter" |
| depends on I2C |
| select IIO_BUFFER |
| select IIO_TRIGGERED_BUFFER |
| help |
| If you say yes here you get support for the TAOS TCS3472 |
| family of color light-to-digital converters with IR filter. |
| |
| This driver can also be built as a module. If so, the module |
| will be called tcs3472. |
| |
| config SENSORS_TSL2563 |
| tristate "TAOS TSL2560, TSL2561, TSL2562 and TSL2563 ambient light sensors" |
| depends on I2C |
| help |
| If you say yes here you get support for the Taos TSL2560, |
| TSL2561, TSL2562 and TSL2563 ambient light sensors. |
| |
| This driver can also be built as a module. If so, the module |
| will be called tsl2563. |
| |
| config TSL2583 |
| tristate "TAOS TSL2580, TSL2581 and TSL2583 light-to-digital converters" |
| depends on I2C |
| help |
| Provides support for the TAOS tsl2580, tsl2581 and tsl2583 devices. |
| Access ALS data via iio, sysfs. |
| |
| config TSL2591 |
| tristate "TAOS TSL2591 ambient light sensor" |
| depends on I2C |
| help |
| Select Y here for support of the AMS/TAOS TSL2591 ambient light sensor, |
| featuring channels for combined visible + IR intensity and lux illuminance. |
| Access data via iio and sysfs. Supports iio_events. |
| |
| To compile this driver as a module, select M: the |
| module will be called tsl2591. |
| |
| config TSL2772 |
| tristate "TAOS TSL/TMD2x71 and TSL/TMD2x72 Family of light and proximity sensors" |
| depends on I2C |
| help |
| Support for: tsl2571, tsl2671, tmd2671, tsl2771, tmd2771, tsl2572, tsl2672, |
| tmd2672, tsl2772, tmd2772 devices. |
| Provides iio_events and direct access via sysfs. |
| |
| config TSL4531 |
| tristate "TAOS TSL4531 ambient light sensors" |
| depends on I2C |
| help |
| Say Y here if you want to build a driver for the TAOS TSL4531 family |
| of ambient light sensors with direct lux output. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called tsl4531. |
| |
| config US5182D |
| tristate "UPISEMI light and proximity sensor" |
| depends on I2C |
| help |
| If you say yes here you get support for the UPISEMI US5182D |
| ambient light and proximity sensor. |
| |
| This driver can also be built as a module. If so, the module |
| will be called us5182d. |
| |
| config VCNL4000 |
| tristate "VCNL4000/4010/4020/4200 combined ALS and proximity sensor" |
| select IIO_BUFFER |
| select IIO_TRIGGERED_BUFFER |
| depends on I2C |
| help |
| Say Y here if you want to build a driver for the Vishay VCNL4000, |
| VCNL4010, VCNL4020, VCNL4200 combined ambient light and proximity |
| sensor. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called vcnl4000. |
| |
| config VCNL4035 |
| tristate "VCNL4035 combined ALS and proximity sensor" |
| select IIO_BUFFER |
| select IIO_TRIGGERED_BUFFER |
| select REGMAP_I2C |
| depends on I2C |
| help |
| Say Y here if you want to build a driver for the Vishay VCNL4035, |
| combined ambient light (ALS) and proximity sensor. Currently only ALS |
| function is available. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called vcnl4035. |
| |
| config VEML6030 |
| tristate "VEML6030 ambient light sensor" |
| select REGMAP_I2C |
| depends on I2C |
| help |
| Say Y here if you want to build a driver for the Vishay VEML6030 |
| ambient light sensor (ALS). |
| |
| To compile this driver as a module, choose M here: the |
| module will be called veml6030. |
| |
| config VEML6040 |
| tristate "VEML6040 RGBW light sensor" |
| select REGMAP_I2C |
| depends on I2C |
| help |
| Say Y here if you want to build a driver for the Vishay VEML6040 |
| RGBW light sensor. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called veml6040. |
| |
| config VEML6070 |
| tristate "VEML6070 UV A light sensor" |
| depends on I2C |
| help |
| Say Y here if you want to build a driver for the Vishay VEML6070 UV A |
| light sensor. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called veml6070. |
| |
| config VEML6075 |
| tristate "VEML6075 UVA and UVB light sensor" |
| select REGMAP_I2C |
| depends on I2C |
| help |
| Say Y here if you want to build a driver for the Vishay VEML6075 UVA |
| and UVB light sensor. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called veml6075. |
| |
| config VL6180 |
| tristate "VL6180 ALS, range and proximity sensor" |
| depends on I2C |
| help |
| Say Y here if you want to build a driver for the STMicroelectronics |
| VL6180 combined ambient light, range and proximity sensor. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called vl6180. |
| |
| config ZOPT2201 |
| tristate "ZOPT2201 ALS and UV B sensor" |
| depends on I2C |
| help |
| Say Y here if you want to build a driver for the IDT |
| ZOPT2201 ambient light and UV B sensor. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called zopt2201. |
| |
| endmenu |
