| // SPDX-License-Identifier: GPL-2.0-only |
| /* Copyright Altera Corporation (C) 2014. All rights reserved. |
| * |
| * Adopted from dwmac-sti.c |
| */ |
| |
| #include <linux/mfd/altera-sysmgr.h> |
| #include <linux/of.h> |
| #include <linux/of_address.h> |
| #include <linux/of_net.h> |
| #include <linux/phy.h> |
| #include <linux/regmap.h> |
| #include <linux/mdio/mdio-regmap.h> |
| #include <linux/pcs-lynx.h> |
| #include <linux/reset.h> |
| #include <linux/stmmac.h> |
| |
| #include "stmmac.h" |
| #include "stmmac_platform.h" |
| |
| #define SYSMGR_EMACGRP_CTRL_PHYSEL_ENUM_GMII_MII 0x0 |
| #define SYSMGR_EMACGRP_CTRL_PHYSEL_ENUM_RGMII 0x1 |
| #define SYSMGR_EMACGRP_CTRL_PHYSEL_ENUM_RMII 0x2 |
| #define SYSMGR_EMACGRP_CTRL_PHYSEL_WIDTH 2 |
| #define SYSMGR_EMACGRP_CTRL_PHYSEL_MASK 0x00000003 |
| #define SYSMGR_EMACGRP_CTRL_PTP_REF_CLK_MASK 0x00000010 |
| #define SYSMGR_GEN10_EMACGRP_CTRL_PTP_REF_CLK_MASK 0x00000100 |
| |
| #define SYSMGR_FPGAGRP_MODULE_REG 0x00000028 |
| #define SYSMGR_FPGAGRP_MODULE_EMAC 0x00000004 |
| #define SYSMGR_FPGAINTF_EMAC_REG 0x00000070 |
| #define SYSMGR_FPGAINTF_EMAC_BIT 0x1 |
| |
| #define EMAC_SPLITTER_CTRL_REG 0x0 |
| #define EMAC_SPLITTER_CTRL_SPEED_MASK 0x3 |
| #define EMAC_SPLITTER_CTRL_SPEED_10 0x2 |
| #define EMAC_SPLITTER_CTRL_SPEED_100 0x3 |
| #define EMAC_SPLITTER_CTRL_SPEED_1000 0x0 |
| |
| #define SGMII_ADAPTER_CTRL_REG 0x00 |
| #define SGMII_ADAPTER_ENABLE 0x0000 |
| #define SGMII_ADAPTER_DISABLE 0x0001 |
| |
| struct socfpga_dwmac; |
| struct socfpga_dwmac_ops { |
| int (*set_phy_mode)(struct socfpga_dwmac *dwmac_priv); |
| }; |
| |
| struct socfpga_dwmac { |
| u32 reg_offset; |
| u32 reg_shift; |
| struct device *dev; |
| struct regmap *sys_mgr_base_addr; |
| struct reset_control *stmmac_rst; |
| struct reset_control *stmmac_ocp_rst; |
| void __iomem *splitter_base; |
| void __iomem *tse_pcs_base; |
| void __iomem *sgmii_adapter_base; |
| bool f2h_ptp_ref_clk; |
| const struct socfpga_dwmac_ops *ops; |
| struct mdio_device *pcs_mdiodev; |
| }; |
| |
| static void socfpga_dwmac_fix_mac_speed(void *priv, unsigned int speed, unsigned int mode) |
| { |
| struct socfpga_dwmac *dwmac = (struct socfpga_dwmac *)priv; |
| void __iomem *splitter_base = dwmac->splitter_base; |
| void __iomem *sgmii_adapter_base = dwmac->sgmii_adapter_base; |
| struct device *dev = dwmac->dev; |
| struct net_device *ndev = dev_get_drvdata(dev); |
| struct phy_device *phy_dev = ndev->phydev; |
| u32 val; |
| |
| if (sgmii_adapter_base) |
| writew(SGMII_ADAPTER_DISABLE, |
| sgmii_adapter_base + SGMII_ADAPTER_CTRL_REG); |
| |
| if (splitter_base) { |
| val = readl(splitter_base + EMAC_SPLITTER_CTRL_REG); |
| val &= ~EMAC_SPLITTER_CTRL_SPEED_MASK; |
| |
| switch (speed) { |
| case 1000: |
| val |= EMAC_SPLITTER_CTRL_SPEED_1000; |
| break; |
| case 100: |
| val |= EMAC_SPLITTER_CTRL_SPEED_100; |
| break; |
| case 10: |
| val |= EMAC_SPLITTER_CTRL_SPEED_10; |
| break; |
| default: |
| return; |
| } |
| writel(val, splitter_base + EMAC_SPLITTER_CTRL_REG); |
| } |
| |
| if (phy_dev && sgmii_adapter_base) |
| writew(SGMII_ADAPTER_ENABLE, |
| sgmii_adapter_base + SGMII_ADAPTER_CTRL_REG); |
| } |
| |
| static int socfpga_dwmac_parse_data(struct socfpga_dwmac *dwmac, struct device *dev) |
| { |
| struct device_node *np = dev->of_node; |
| struct regmap *sys_mgr_base_addr; |
| u32 reg_offset, reg_shift; |
| int ret, index; |
| struct device_node *np_splitter = NULL; |
| struct device_node *np_sgmii_adapter = NULL; |
| struct resource res_splitter; |
| struct resource res_tse_pcs; |
| struct resource res_sgmii_adapter; |
| |
| sys_mgr_base_addr = |
| altr_sysmgr_regmap_lookup_by_phandle(np, "altr,sysmgr-syscon"); |
| if (IS_ERR(sys_mgr_base_addr)) { |
| dev_info(dev, "No sysmgr-syscon node found\n"); |
| return PTR_ERR(sys_mgr_base_addr); |
| } |
| |
| ret = of_property_read_u32_index(np, "altr,sysmgr-syscon", 1, ®_offset); |
| if (ret) { |
| dev_info(dev, "Could not read reg_offset from sysmgr-syscon!\n"); |
| return -EINVAL; |
| } |
| |
| ret = of_property_read_u32_index(np, "altr,sysmgr-syscon", 2, ®_shift); |
| if (ret) { |
| dev_info(dev, "Could not read reg_shift from sysmgr-syscon!\n"); |
| return -EINVAL; |
| } |
| |
| dwmac->f2h_ptp_ref_clk = of_property_read_bool(np, "altr,f2h_ptp_ref_clk"); |
| |
| np_splitter = of_parse_phandle(np, "altr,emac-splitter", 0); |
| if (np_splitter) { |
| ret = of_address_to_resource(np_splitter, 0, &res_splitter); |
| of_node_put(np_splitter); |
| if (ret) { |
| dev_info(dev, "Missing emac splitter address\n"); |
| return -EINVAL; |
| } |
| |
| dwmac->splitter_base = devm_ioremap_resource(dev, &res_splitter); |
| if (IS_ERR(dwmac->splitter_base)) { |
| dev_info(dev, "Failed to mapping emac splitter\n"); |
| return PTR_ERR(dwmac->splitter_base); |
| } |
| } |
| |
| np_sgmii_adapter = of_parse_phandle(np, |
| "altr,gmii-to-sgmii-converter", 0); |
| if (np_sgmii_adapter) { |
| index = of_property_match_string(np_sgmii_adapter, "reg-names", |
| "hps_emac_interface_splitter_avalon_slave"); |
| |
| if (index >= 0) { |
| if (of_address_to_resource(np_sgmii_adapter, index, |
| &res_splitter)) { |
| dev_err(dev, |
| "%s: ERROR: missing emac splitter address\n", |
| __func__); |
| ret = -EINVAL; |
| goto err_node_put; |
| } |
| |
| dwmac->splitter_base = |
| devm_ioremap_resource(dev, &res_splitter); |
| |
| if (IS_ERR(dwmac->splitter_base)) { |
| ret = PTR_ERR(dwmac->splitter_base); |
| goto err_node_put; |
| } |
| } |
| |
| index = of_property_match_string(np_sgmii_adapter, "reg-names", |
| "gmii_to_sgmii_adapter_avalon_slave"); |
| |
| if (index >= 0) { |
| if (of_address_to_resource(np_sgmii_adapter, index, |
| &res_sgmii_adapter)) { |
| dev_err(dev, |
| "%s: ERROR: failed mapping adapter\n", |
| __func__); |
| ret = -EINVAL; |
| goto err_node_put; |
| } |
| |
| dwmac->sgmii_adapter_base = |
| devm_ioremap_resource(dev, &res_sgmii_adapter); |
| |
| if (IS_ERR(dwmac->sgmii_adapter_base)) { |
| ret = PTR_ERR(dwmac->sgmii_adapter_base); |
| goto err_node_put; |
| } |
| } |
| |
| index = of_property_match_string(np_sgmii_adapter, "reg-names", |
| "eth_tse_control_port"); |
| |
| if (index >= 0) { |
| if (of_address_to_resource(np_sgmii_adapter, index, |
| &res_tse_pcs)) { |
| dev_err(dev, |
| "%s: ERROR: failed mapping tse control port\n", |
| __func__); |
| ret = -EINVAL; |
| goto err_node_put; |
| } |
| |
| dwmac->tse_pcs_base = |
| devm_ioremap_resource(dev, &res_tse_pcs); |
| |
| if (IS_ERR(dwmac->tse_pcs_base)) { |
| ret = PTR_ERR(dwmac->tse_pcs_base); |
| goto err_node_put; |
| } |
| } |
| } |
| dwmac->reg_offset = reg_offset; |
| dwmac->reg_shift = reg_shift; |
| dwmac->sys_mgr_base_addr = sys_mgr_base_addr; |
| dwmac->dev = dev; |
| of_node_put(np_sgmii_adapter); |
| |
| return 0; |
| |
| err_node_put: |
| of_node_put(np_sgmii_adapter); |
| return ret; |
| } |
| |
| static int socfpga_get_plat_phymode(struct socfpga_dwmac *dwmac) |
| { |
| struct net_device *ndev = dev_get_drvdata(dwmac->dev); |
| struct stmmac_priv *priv = netdev_priv(ndev); |
| |
| return priv->plat->mac_interface; |
| } |
| |
| static void socfpga_sgmii_config(struct socfpga_dwmac *dwmac, bool enable) |
| { |
| u16 val = enable ? SGMII_ADAPTER_ENABLE : SGMII_ADAPTER_DISABLE; |
| |
| writew(val, dwmac->sgmii_adapter_base + SGMII_ADAPTER_CTRL_REG); |
| } |
| |
| static int socfpga_set_phy_mode_common(int phymode, u32 *val) |
| { |
| switch (phymode) { |
| case PHY_INTERFACE_MODE_RGMII: |
| case PHY_INTERFACE_MODE_RGMII_ID: |
| case PHY_INTERFACE_MODE_RGMII_RXID: |
| case PHY_INTERFACE_MODE_RGMII_TXID: |
| *val = SYSMGR_EMACGRP_CTRL_PHYSEL_ENUM_RGMII; |
| break; |
| case PHY_INTERFACE_MODE_MII: |
| case PHY_INTERFACE_MODE_GMII: |
| case PHY_INTERFACE_MODE_SGMII: |
| *val = SYSMGR_EMACGRP_CTRL_PHYSEL_ENUM_GMII_MII; |
| break; |
| case PHY_INTERFACE_MODE_RMII: |
| *val = SYSMGR_EMACGRP_CTRL_PHYSEL_ENUM_RMII; |
| break; |
| default: |
| return -EINVAL; |
| } |
| return 0; |
| } |
| |
| static int socfpga_gen5_set_phy_mode(struct socfpga_dwmac *dwmac) |
| { |
| struct regmap *sys_mgr_base_addr = dwmac->sys_mgr_base_addr; |
| int phymode = socfpga_get_plat_phymode(dwmac); |
| u32 reg_offset = dwmac->reg_offset; |
| u32 reg_shift = dwmac->reg_shift; |
| u32 ctrl, val, module; |
| |
| if (socfpga_set_phy_mode_common(phymode, &val)) { |
| dev_err(dwmac->dev, "bad phy mode %d\n", phymode); |
| return -EINVAL; |
| } |
| |
| /* Overwrite val to GMII if splitter core is enabled. The phymode here |
| * is the actual phy mode on phy hardware, but phy interface from |
| * EMAC core is GMII. |
| */ |
| if (dwmac->splitter_base) |
| val = SYSMGR_EMACGRP_CTRL_PHYSEL_ENUM_GMII_MII; |
| |
| /* Assert reset to the enet controller before changing the phy mode */ |
| reset_control_assert(dwmac->stmmac_ocp_rst); |
| reset_control_assert(dwmac->stmmac_rst); |
| |
| regmap_read(sys_mgr_base_addr, reg_offset, &ctrl); |
| ctrl &= ~(SYSMGR_EMACGRP_CTRL_PHYSEL_MASK << reg_shift); |
| ctrl |= val << reg_shift; |
| |
| if (dwmac->f2h_ptp_ref_clk || |
| phymode == PHY_INTERFACE_MODE_MII || |
| phymode == PHY_INTERFACE_MODE_GMII || |
| phymode == PHY_INTERFACE_MODE_SGMII) { |
| regmap_read(sys_mgr_base_addr, SYSMGR_FPGAGRP_MODULE_REG, |
| &module); |
| module |= (SYSMGR_FPGAGRP_MODULE_EMAC << (reg_shift / 2)); |
| regmap_write(sys_mgr_base_addr, SYSMGR_FPGAGRP_MODULE_REG, |
| module); |
| } |
| |
| if (dwmac->f2h_ptp_ref_clk) |
| ctrl |= SYSMGR_EMACGRP_CTRL_PTP_REF_CLK_MASK << (reg_shift / 2); |
| else |
| ctrl &= ~(SYSMGR_EMACGRP_CTRL_PTP_REF_CLK_MASK << |
| (reg_shift / 2)); |
| |
| regmap_write(sys_mgr_base_addr, reg_offset, ctrl); |
| |
| /* Deassert reset for the phy configuration to be sampled by |
| * the enet controller, and operation to start in requested mode |
| */ |
| reset_control_deassert(dwmac->stmmac_ocp_rst); |
| reset_control_deassert(dwmac->stmmac_rst); |
| if (phymode == PHY_INTERFACE_MODE_SGMII) |
| socfpga_sgmii_config(dwmac, true); |
| |
| return 0; |
| } |
| |
| static int socfpga_gen10_set_phy_mode(struct socfpga_dwmac *dwmac) |
| { |
| struct regmap *sys_mgr_base_addr = dwmac->sys_mgr_base_addr; |
| int phymode = socfpga_get_plat_phymode(dwmac); |
| u32 reg_offset = dwmac->reg_offset; |
| u32 reg_shift = dwmac->reg_shift; |
| u32 ctrl, val, module; |
| |
| if (socfpga_set_phy_mode_common(phymode, &val)) |
| return -EINVAL; |
| |
| /* Overwrite val to GMII if splitter core is enabled. The phymode here |
| * is the actual phy mode on phy hardware, but phy interface from |
| * EMAC core is GMII. |
| */ |
| if (dwmac->splitter_base) |
| val = SYSMGR_EMACGRP_CTRL_PHYSEL_ENUM_GMII_MII; |
| |
| /* Assert reset to the enet controller before changing the phy mode */ |
| reset_control_assert(dwmac->stmmac_ocp_rst); |
| reset_control_assert(dwmac->stmmac_rst); |
| |
| regmap_read(sys_mgr_base_addr, reg_offset, &ctrl); |
| ctrl &= ~(SYSMGR_EMACGRP_CTRL_PHYSEL_MASK); |
| ctrl |= val; |
| |
| if (dwmac->f2h_ptp_ref_clk || |
| phymode == PHY_INTERFACE_MODE_MII || |
| phymode == PHY_INTERFACE_MODE_GMII || |
| phymode == PHY_INTERFACE_MODE_SGMII) { |
| ctrl |= SYSMGR_GEN10_EMACGRP_CTRL_PTP_REF_CLK_MASK; |
| regmap_read(sys_mgr_base_addr, SYSMGR_FPGAINTF_EMAC_REG, |
| &module); |
| module |= (SYSMGR_FPGAINTF_EMAC_BIT << reg_shift); |
| regmap_write(sys_mgr_base_addr, SYSMGR_FPGAINTF_EMAC_REG, |
| module); |
| } else { |
| ctrl &= ~SYSMGR_GEN10_EMACGRP_CTRL_PTP_REF_CLK_MASK; |
| } |
| |
| regmap_write(sys_mgr_base_addr, reg_offset, ctrl); |
| |
| /* Deassert reset for the phy configuration to be sampled by |
| * the enet controller, and operation to start in requested mode |
| */ |
| reset_control_deassert(dwmac->stmmac_ocp_rst); |
| reset_control_deassert(dwmac->stmmac_rst); |
| if (phymode == PHY_INTERFACE_MODE_SGMII) |
| socfpga_sgmii_config(dwmac, true); |
| return 0; |
| } |
| |
| static int socfpga_dwmac_pcs_init(struct stmmac_priv *priv) |
| { |
| struct socfpga_dwmac *dwmac = priv->plat->bsp_priv; |
| struct regmap_config pcs_regmap_cfg = { |
| .reg_bits = 16, |
| .val_bits = 16, |
| .reg_shift = REGMAP_UPSHIFT(1), |
| }; |
| struct mdio_regmap_config mrc; |
| struct regmap *pcs_regmap; |
| struct phylink_pcs *pcs; |
| struct mii_bus *pcs_bus; |
| |
| if (!dwmac->tse_pcs_base) |
| return 0; |
| |
| pcs_regmap = devm_regmap_init_mmio(priv->device, dwmac->tse_pcs_base, |
| &pcs_regmap_cfg); |
| if (IS_ERR(pcs_regmap)) |
| return PTR_ERR(pcs_regmap); |
| |
| memset(&mrc, 0, sizeof(mrc)); |
| mrc.regmap = pcs_regmap; |
| mrc.parent = priv->device; |
| mrc.valid_addr = 0x0; |
| mrc.autoscan = false; |
| |
| /* Can't use ndev->name here because it will not have been initialised, |
| * and in any case, the user can rename network interfaces at runtime. |
| */ |
| snprintf(mrc.name, MII_BUS_ID_SIZE, "%s-pcs-mii", |
| dev_name(priv->device)); |
| pcs_bus = devm_mdio_regmap_register(priv->device, &mrc); |
| if (IS_ERR(pcs_bus)) |
| return PTR_ERR(pcs_bus); |
| |
| pcs = lynx_pcs_create_mdiodev(pcs_bus, 0); |
| if (IS_ERR(pcs)) |
| return PTR_ERR(pcs); |
| |
| priv->hw->phylink_pcs = pcs; |
| return 0; |
| } |
| |
| static void socfpga_dwmac_pcs_exit(struct stmmac_priv *priv) |
| { |
| if (priv->hw->phylink_pcs) |
| lynx_pcs_destroy(priv->hw->phylink_pcs); |
| } |
| |
| static struct phylink_pcs *socfpga_dwmac_select_pcs(struct stmmac_priv *priv, |
| phy_interface_t interface) |
| { |
| return priv->hw->phylink_pcs; |
| } |
| |
| static int socfpga_dwmac_probe(struct platform_device *pdev) |
| { |
| struct plat_stmmacenet_data *plat_dat; |
| struct stmmac_resources stmmac_res; |
| struct device *dev = &pdev->dev; |
| int ret; |
| struct socfpga_dwmac *dwmac; |
| struct net_device *ndev; |
| struct stmmac_priv *stpriv; |
| const struct socfpga_dwmac_ops *ops; |
| |
| ops = device_get_match_data(&pdev->dev); |
| if (!ops) { |
| dev_err(&pdev->dev, "no of match data provided\n"); |
| return -EINVAL; |
| } |
| |
| ret = stmmac_get_platform_resources(pdev, &stmmac_res); |
| if (ret) |
| return ret; |
| |
| plat_dat = devm_stmmac_probe_config_dt(pdev, stmmac_res.mac); |
| if (IS_ERR(plat_dat)) |
| return PTR_ERR(plat_dat); |
| |
| dwmac = devm_kzalloc(dev, sizeof(*dwmac), GFP_KERNEL); |
| if (!dwmac) |
| return -ENOMEM; |
| |
| dwmac->stmmac_ocp_rst = devm_reset_control_get_optional(dev, "stmmaceth-ocp"); |
| if (IS_ERR(dwmac->stmmac_ocp_rst)) { |
| ret = PTR_ERR(dwmac->stmmac_ocp_rst); |
| dev_err(dev, "error getting reset control of ocp %d\n", ret); |
| return ret; |
| } |
| |
| reset_control_deassert(dwmac->stmmac_ocp_rst); |
| |
| ret = socfpga_dwmac_parse_data(dwmac, dev); |
| if (ret) { |
| dev_err(dev, "Unable to parse OF data\n"); |
| return ret; |
| } |
| |
| dwmac->ops = ops; |
| plat_dat->bsp_priv = dwmac; |
| plat_dat->fix_mac_speed = socfpga_dwmac_fix_mac_speed; |
| plat_dat->pcs_init = socfpga_dwmac_pcs_init; |
| plat_dat->pcs_exit = socfpga_dwmac_pcs_exit; |
| plat_dat->select_pcs = socfpga_dwmac_select_pcs; |
| |
| ret = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res); |
| if (ret) |
| return ret; |
| |
| ndev = platform_get_drvdata(pdev); |
| stpriv = netdev_priv(ndev); |
| |
| /* The socfpga driver needs to control the stmmac reset to set the phy |
| * mode. Create a copy of the core reset handle so it can be used by |
| * the driver later. |
| */ |
| dwmac->stmmac_rst = stpriv->plat->stmmac_rst; |
| |
| ret = ops->set_phy_mode(dwmac); |
| if (ret) |
| goto err_dvr_remove; |
| |
| return 0; |
| |
| err_dvr_remove: |
| stmmac_dvr_remove(&pdev->dev); |
| |
| return ret; |
| } |
| |
| #ifdef CONFIG_PM_SLEEP |
| static int socfpga_dwmac_resume(struct device *dev) |
| { |
| struct net_device *ndev = dev_get_drvdata(dev); |
| struct stmmac_priv *priv = netdev_priv(ndev); |
| struct socfpga_dwmac *dwmac_priv = get_stmmac_bsp_priv(dev); |
| |
| dwmac_priv->ops->set_phy_mode(priv->plat->bsp_priv); |
| |
| /* Before the enet controller is suspended, the phy is suspended. |
| * This causes the phy clock to be gated. The enet controller is |
| * resumed before the phy, so the clock is still gated "off" when |
| * the enet controller is resumed. This code makes sure the phy |
| * is "resumed" before reinitializing the enet controller since |
| * the enet controller depends on an active phy clock to complete |
| * a DMA reset. A DMA reset will "time out" if executed |
| * with no phy clock input on the Synopsys enet controller. |
| * Verified through Synopsys Case #8000711656. |
| * |
| * Note that the phy clock is also gated when the phy is isolated. |
| * Phy "suspend" and "isolate" controls are located in phy basic |
| * control register 0, and can be modified by the phy driver |
| * framework. |
| */ |
| if (ndev->phydev) |
| phy_resume(ndev->phydev); |
| |
| return stmmac_resume(dev); |
| } |
| #endif /* CONFIG_PM_SLEEP */ |
| |
| static int __maybe_unused socfpga_dwmac_runtime_suspend(struct device *dev) |
| { |
| struct net_device *ndev = dev_get_drvdata(dev); |
| struct stmmac_priv *priv = netdev_priv(ndev); |
| |
| stmmac_bus_clks_config(priv, false); |
| |
| return 0; |
| } |
| |
| static int __maybe_unused socfpga_dwmac_runtime_resume(struct device *dev) |
| { |
| struct net_device *ndev = dev_get_drvdata(dev); |
| struct stmmac_priv *priv = netdev_priv(ndev); |
| |
| return stmmac_bus_clks_config(priv, true); |
| } |
| |
| static const struct dev_pm_ops socfpga_dwmac_pm_ops = { |
| SET_SYSTEM_SLEEP_PM_OPS(stmmac_suspend, socfpga_dwmac_resume) |
| SET_RUNTIME_PM_OPS(socfpga_dwmac_runtime_suspend, socfpga_dwmac_runtime_resume, NULL) |
| }; |
| |
| static const struct socfpga_dwmac_ops socfpga_gen5_ops = { |
| .set_phy_mode = socfpga_gen5_set_phy_mode, |
| }; |
| |
| static const struct socfpga_dwmac_ops socfpga_gen10_ops = { |
| .set_phy_mode = socfpga_gen10_set_phy_mode, |
| }; |
| |
| static const struct of_device_id socfpga_dwmac_match[] = { |
| { .compatible = "altr,socfpga-stmmac", .data = &socfpga_gen5_ops }, |
| { .compatible = "altr,socfpga-stmmac-a10-s10", .data = &socfpga_gen10_ops }, |
| { } |
| }; |
| MODULE_DEVICE_TABLE(of, socfpga_dwmac_match); |
| |
| static struct platform_driver socfpga_dwmac_driver = { |
| .probe = socfpga_dwmac_probe, |
| .remove_new = stmmac_pltfr_remove, |
| .driver = { |
| .name = "socfpga-dwmac", |
| .pm = &socfpga_dwmac_pm_ops, |
| .of_match_table = socfpga_dwmac_match, |
| }, |
| }; |
| module_platform_driver(socfpga_dwmac_driver); |
| |
| MODULE_DESCRIPTION("Altera SOC DWMAC Specific Glue layer"); |
| MODULE_LICENSE("GPL v2"); |