| // SPDX-License-Identifier: GPL-2.0 |
| // Copyright (c) 2018, Linaro Limited |
| |
| #include <dt-bindings/spmi/spmi.h> |
| #include <dt-bindings/input/linux-event-codes.h> |
| #include <dt-bindings/iio/qcom,spmi-vadc.h> |
| #include <dt-bindings/thermal/thermal.h> |
| |
| / { |
| thermal-zones { |
| pms405 { |
| polling-delay-passive = <250>; |
| polling-delay = <1000>; |
| |
| thermal-sensors = <&pms405_temp>; |
| |
| trips { |
| pms405_alert0: pms405-alert0 { |
| temperature = <105000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| pms405_crit: pms405-crit { |
| temperature = <125000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| &spmi_bus { |
| pms405_0: pms405@0 { |
| compatible = "qcom,spmi-pmic"; |
| reg = <0x0 SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pms405_gpios: gpio@c000 { |
| compatible = "qcom,pms405-gpio"; |
| reg = <0xc000>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupts = <0 0xc0 0 IRQ_TYPE_NONE>, |
| <0 0xc1 0 IRQ_TYPE_NONE>, |
| <0 0xc2 0 IRQ_TYPE_NONE>, |
| <0 0xc3 0 IRQ_TYPE_NONE>, |
| <0 0xc4 0 IRQ_TYPE_NONE>, |
| <0 0xc5 0 IRQ_TYPE_NONE>, |
| <0 0xc6 0 IRQ_TYPE_NONE>, |
| <0 0xc7 0 IRQ_TYPE_NONE>, |
| <0 0xc8 0 IRQ_TYPE_NONE>, |
| <0 0xc9 0 IRQ_TYPE_NONE>, |
| <0 0xca 0 IRQ_TYPE_NONE>, |
| <0 0xcb 0 IRQ_TYPE_NONE>; |
| }; |
| |
| pon@800 { |
| compatible = "qcom,pms405-pon"; |
| reg = <0x0800>; |
| mode-bootloader = <0x2>; |
| mode-recovery = <0x1>; |
| |
| pwrkey { |
| compatible = "qcom,pm8941-pwrkey"; |
| interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>; |
| debounce = <15625>; |
| bias-pull-up; |
| linux,code = <KEY_POWER>; |
| }; |
| }; |
| |
| pms405_temp: temp-alarm@2400 { |
| compatible = "qcom,spmi-temp-alarm"; |
| reg = <0x2400>; |
| interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>; |
| io-channels = <&pms405_adc ADC5_DIE_TEMP>; |
| io-channel-names = "thermal"; |
| #thermal-sensor-cells = <0>; |
| }; |
| |
| pms405_adc: adc@3100 { |
| compatible = "qcom,pms405-adc", "qcom,spmi-adc-rev2"; |
| reg = <0x3100>; |
| interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #io-channel-cells = <1>; |
| |
| ref_gnd@0 { |
| reg = <ADC5_REF_GND>; |
| qcom,pre-scaling = <1 1>; |
| }; |
| |
| vref_1p25@1 { |
| reg = <ADC5_1P25VREF>; |
| qcom,pre-scaling = <1 1>; |
| }; |
| |
| pon_1: vph_pwr@131 { |
| reg = <ADC5_VPH_PWR>; |
| qcom,pre-scaling = <1 3>; |
| }; |
| |
| die_temp@6 { |
| reg = <ADC5_DIE_TEMP>; |
| qcom,pre-scaling = <1 1>; |
| }; |
| |
| pa_therm1: thermistor1@77 { |
| reg = <ADC5_AMUX_THM1_100K_PU>; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| qcom,pre-scaling = <1 1>; |
| }; |
| |
| pa_therm3: thermistor3@79 { |
| reg = <ADC5_AMUX_THM3_100K_PU>; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| qcom,pre-scaling = <1 1>; |
| }; |
| |
| xo_therm: xo_temp@76 { |
| reg = <ADC5_XO_THERM_100K_PU>; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| qcom,pre-scaling = <1 1>; |
| }; |
| }; |
| |
| rtc@6000 { |
| compatible = "qcom,pm8941-rtc"; |
| reg = <0x6000>; |
| reg-names = "rtc", "alarm"; |
| interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>; |
| }; |
| }; |
| |
| pms405_1: pms405@1 { |
| compatible = "qcom,spmi-pmic"; |
| reg = <0x1 SPMI_USID>; |
| |
| pms405_spmi_regulators: regulators { |
| compatible = "qcom,pms405-regulators"; |
| }; |
| }; |
| }; |