| // SPDX-License-Identifier: GPL-2.0 |
| /* Copyright(c) 2007 - 2018 Intel Corporation. */ |
| |
| #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt |
| |
| #include <linux/module.h> |
| #include <linux/types.h> |
| #include <linux/init.h> |
| #include <linux/bitops.h> |
| #include <linux/vmalloc.h> |
| #include <linux/pagemap.h> |
| #include <linux/netdevice.h> |
| #include <linux/ipv6.h> |
| #include <linux/slab.h> |
| #include <net/checksum.h> |
| #include <net/ip6_checksum.h> |
| #include <net/pkt_sched.h> |
| #include <net/pkt_cls.h> |
| #include <linux/net_tstamp.h> |
| #include <linux/mii.h> |
| #include <linux/ethtool.h> |
| #include <linux/if.h> |
| #include <linux/if_vlan.h> |
| #include <linux/pci.h> |
| #include <linux/delay.h> |
| #include <linux/interrupt.h> |
| #include <linux/ip.h> |
| #include <linux/tcp.h> |
| #include <linux/sctp.h> |
| #include <linux/if_ether.h> |
| #include <linux/prefetch.h> |
| #include <linux/bpf.h> |
| #include <linux/bpf_trace.h> |
| #include <linux/pm_runtime.h> |
| #include <linux/etherdevice.h> |
| #ifdef CONFIG_IGB_DCA |
| #include <linux/dca.h> |
| #endif |
| #include <linux/i2c.h> |
| #include "igb.h" |
| |
| enum queue_mode { |
| QUEUE_MODE_STRICT_PRIORITY, |
| QUEUE_MODE_STREAM_RESERVATION, |
| }; |
| |
| enum tx_queue_prio { |
| TX_QUEUE_PRIO_HIGH, |
| TX_QUEUE_PRIO_LOW, |
| }; |
| |
| char igb_driver_name[] = "igb"; |
| static const char igb_driver_string[] = |
| "Intel(R) Gigabit Ethernet Network Driver"; |
| static const char igb_copyright[] = |
| "Copyright (c) 2007-2014 Intel Corporation."; |
| |
| static const struct e1000_info *igb_info_tbl[] = { |
| [board_82575] = &e1000_82575_info, |
| }; |
| |
| static const struct pci_device_id igb_pci_tbl[] = { |
| { PCI_VDEVICE(INTEL, E1000_DEV_ID_I354_BACKPLANE_1GBPS) }, |
| { PCI_VDEVICE(INTEL, E1000_DEV_ID_I354_SGMII) }, |
| { PCI_VDEVICE(INTEL, E1000_DEV_ID_I354_BACKPLANE_2_5GBPS) }, |
| { PCI_VDEVICE(INTEL, E1000_DEV_ID_I211_COPPER), board_82575 }, |
| { PCI_VDEVICE(INTEL, E1000_DEV_ID_I210_COPPER), board_82575 }, |
| { PCI_VDEVICE(INTEL, E1000_DEV_ID_I210_FIBER), board_82575 }, |
| { PCI_VDEVICE(INTEL, E1000_DEV_ID_I210_SERDES), board_82575 }, |
| { PCI_VDEVICE(INTEL, E1000_DEV_ID_I210_SGMII), board_82575 }, |
| { PCI_VDEVICE(INTEL, E1000_DEV_ID_I210_COPPER_FLASHLESS), board_82575 }, |
| { PCI_VDEVICE(INTEL, E1000_DEV_ID_I210_SERDES_FLASHLESS), board_82575 }, |
| { PCI_VDEVICE(INTEL, E1000_DEV_ID_I350_COPPER), board_82575 }, |
| { PCI_VDEVICE(INTEL, E1000_DEV_ID_I350_FIBER), board_82575 }, |
| { PCI_VDEVICE(INTEL, E1000_DEV_ID_I350_SERDES), board_82575 }, |
| { PCI_VDEVICE(INTEL, E1000_DEV_ID_I350_SGMII), board_82575 }, |
| { PCI_VDEVICE(INTEL, E1000_DEV_ID_82580_COPPER), board_82575 }, |
| { PCI_VDEVICE(INTEL, E1000_DEV_ID_82580_FIBER), board_82575 }, |
| { PCI_VDEVICE(INTEL, E1000_DEV_ID_82580_QUAD_FIBER), board_82575 }, |
| { PCI_VDEVICE(INTEL, E1000_DEV_ID_82580_SERDES), board_82575 }, |
| { PCI_VDEVICE(INTEL, E1000_DEV_ID_82580_SGMII), board_82575 }, |
| { PCI_VDEVICE(INTEL, E1000_DEV_ID_82580_COPPER_DUAL), board_82575 }, |
| { PCI_VDEVICE(INTEL, E1000_DEV_ID_DH89XXCC_SGMII), board_82575 }, |
| { PCI_VDEVICE(INTEL, E1000_DEV_ID_DH89XXCC_SERDES), board_82575 }, |
| { PCI_VDEVICE(INTEL, E1000_DEV_ID_DH89XXCC_BACKPLANE), board_82575 }, |
| { PCI_VDEVICE(INTEL, E1000_DEV_ID_DH89XXCC_SFP), board_82575 }, |
| { PCI_VDEVICE(INTEL, E1000_DEV_ID_82576), board_82575 }, |
| { PCI_VDEVICE(INTEL, E1000_DEV_ID_82576_NS), board_82575 }, |
| { PCI_VDEVICE(INTEL, E1000_DEV_ID_82576_NS_SERDES), board_82575 }, |
| { PCI_VDEVICE(INTEL, E1000_DEV_ID_82576_FIBER), board_82575 }, |
| { PCI_VDEVICE(INTEL, E1000_DEV_ID_82576_SERDES), board_82575 }, |
| { PCI_VDEVICE(INTEL, E1000_DEV_ID_82576_SERDES_QUAD), board_82575 }, |
| { PCI_VDEVICE(INTEL, E1000_DEV_ID_82576_QUAD_COPPER_ET2), board_82575 }, |
| { PCI_VDEVICE(INTEL, E1000_DEV_ID_82576_QUAD_COPPER), board_82575 }, |
| { PCI_VDEVICE(INTEL, E1000_DEV_ID_82575EB_COPPER), board_82575 }, |
| { PCI_VDEVICE(INTEL, E1000_DEV_ID_82575EB_FIBER_SERDES), board_82575 }, |
| { PCI_VDEVICE(INTEL, E1000_DEV_ID_82575GB_QUAD_COPPER), board_82575 }, |
| /* required last entry */ |
| {0, } |
| }; |
| |
| MODULE_DEVICE_TABLE(pci, igb_pci_tbl); |
| |
| static int igb_setup_all_tx_resources(struct igb_adapter *); |
| static int igb_setup_all_rx_resources(struct igb_adapter *); |
| static void igb_free_all_tx_resources(struct igb_adapter *); |
| static void igb_free_all_rx_resources(struct igb_adapter *); |
| static void igb_setup_mrqc(struct igb_adapter *); |
| static void igb_init_queue_configuration(struct igb_adapter *adapter); |
| static int igb_sw_init(struct igb_adapter *); |
| int igb_open(struct net_device *); |
| int igb_close(struct net_device *); |
| static void igb_configure(struct igb_adapter *); |
| static void igb_configure_tx(struct igb_adapter *); |
| static void igb_configure_rx(struct igb_adapter *); |
| static void igb_clean_all_tx_rings(struct igb_adapter *); |
| static void igb_clean_all_rx_rings(struct igb_adapter *); |
| static void igb_clean_tx_ring(struct igb_ring *); |
| static void igb_clean_rx_ring(struct igb_ring *); |
| static void igb_set_rx_mode(struct net_device *); |
| static void igb_update_phy_info(struct timer_list *); |
| static void igb_watchdog(struct timer_list *); |
| static void igb_watchdog_task(struct work_struct *); |
| static netdev_tx_t igb_xmit_frame(struct sk_buff *skb, struct net_device *); |
| static void igb_get_stats64(struct net_device *dev, |
| struct rtnl_link_stats64 *stats); |
| static int igb_change_mtu(struct net_device *, int); |
| static int igb_set_mac(struct net_device *, void *); |
| static void igb_set_uta(struct igb_adapter *adapter, bool set); |
| static irqreturn_t igb_intr(int irq, void *); |
| static irqreturn_t igb_intr_msi(int irq, void *); |
| static irqreturn_t igb_msix_other(int irq, void *); |
| static irqreturn_t igb_msix_ring(int irq, void *); |
| #ifdef CONFIG_IGB_DCA |
| static void igb_update_dca(struct igb_q_vector *); |
| static void igb_setup_dca(struct igb_adapter *); |
| #endif /* CONFIG_IGB_DCA */ |
| static int igb_poll(struct napi_struct *, int); |
| static bool igb_clean_tx_irq(struct igb_q_vector *, int); |
| static int igb_clean_rx_irq(struct igb_q_vector *, int); |
| static int igb_ioctl(struct net_device *, struct ifreq *, int cmd); |
| static void igb_tx_timeout(struct net_device *, unsigned int txqueue); |
| static void igb_reset_task(struct work_struct *); |
| static void igb_vlan_mode(struct net_device *netdev, |
| netdev_features_t features); |
| static int igb_vlan_rx_add_vid(struct net_device *, __be16, u16); |
| static int igb_vlan_rx_kill_vid(struct net_device *, __be16, u16); |
| static void igb_restore_vlan(struct igb_adapter *); |
| static void igb_rar_set_index(struct igb_adapter *, u32); |
| static void igb_ping_all_vfs(struct igb_adapter *); |
| static void igb_msg_task(struct igb_adapter *); |
| static void igb_vmm_control(struct igb_adapter *); |
| static int igb_set_vf_mac(struct igb_adapter *, int, unsigned char *); |
| static void igb_flush_mac_table(struct igb_adapter *); |
| static int igb_available_rars(struct igb_adapter *, u8); |
| static void igb_set_default_mac_filter(struct igb_adapter *); |
| static int igb_uc_sync(struct net_device *, const unsigned char *); |
| static int igb_uc_unsync(struct net_device *, const unsigned char *); |
| static void igb_restore_vf_multicasts(struct igb_adapter *adapter); |
| static int igb_ndo_set_vf_mac(struct net_device *netdev, int vf, u8 *mac); |
| static int igb_ndo_set_vf_vlan(struct net_device *netdev, |
| int vf, u16 vlan, u8 qos, __be16 vlan_proto); |
| static int igb_ndo_set_vf_bw(struct net_device *, int, int, int); |
| static int igb_ndo_set_vf_spoofchk(struct net_device *netdev, int vf, |
| bool setting); |
| static int igb_ndo_set_vf_trust(struct net_device *netdev, int vf, |
| bool setting); |
| static int igb_ndo_get_vf_config(struct net_device *netdev, int vf, |
| struct ifla_vf_info *ivi); |
| static void igb_check_vf_rate_limit(struct igb_adapter *); |
| static void igb_nfc_filter_exit(struct igb_adapter *adapter); |
| static void igb_nfc_filter_restore(struct igb_adapter *adapter); |
| |
| #ifdef CONFIG_PCI_IOV |
| static int igb_vf_configure(struct igb_adapter *adapter, int vf); |
| static int igb_disable_sriov(struct pci_dev *dev, bool reinit); |
| #endif |
| |
| #ifdef CONFIG_IGB_DCA |
| static int igb_notify_dca(struct notifier_block *, unsigned long, void *); |
| static struct notifier_block dca_notifier = { |
| .notifier_call = igb_notify_dca, |
| .next = NULL, |
| .priority = 0 |
| }; |
| #endif |
| #ifdef CONFIG_PCI_IOV |
| static unsigned int max_vfs; |
| module_param(max_vfs, uint, 0444); |
| MODULE_PARM_DESC(max_vfs, "Maximum number of virtual functions to allocate per physical function"); |
| #endif /* CONFIG_PCI_IOV */ |
| |
| static pci_ers_result_t igb_io_error_detected(struct pci_dev *, |
| pci_channel_state_t); |
| static pci_ers_result_t igb_io_slot_reset(struct pci_dev *); |
| static void igb_io_resume(struct pci_dev *); |
| |
| static const struct pci_error_handlers igb_err_handler = { |
| .error_detected = igb_io_error_detected, |
| .slot_reset = igb_io_slot_reset, |
| .resume = igb_io_resume, |
| }; |
| |
| static void igb_init_dmac(struct igb_adapter *adapter, u32 pba); |
| |
| MODULE_DESCRIPTION("Intel(R) Gigabit Ethernet Network Driver"); |
| MODULE_LICENSE("GPL v2"); |
| |
| #define DEFAULT_MSG_ENABLE (NETIF_MSG_DRV|NETIF_MSG_PROBE|NETIF_MSG_LINK) |
| static int debug = -1; |
| module_param(debug, int, 0); |
| MODULE_PARM_DESC(debug, "Debug level (0=none,...,16=all)"); |
| |
| struct igb_reg_info { |
| u32 ofs; |
| char *name; |
| }; |
| |
| static const struct igb_reg_info igb_reg_info_tbl[] = { |
| |
| /* General Registers */ |
| {E1000_CTRL, "CTRL"}, |
| {E1000_STATUS, "STATUS"}, |
| {E1000_CTRL_EXT, "CTRL_EXT"}, |
| |
| /* Interrupt Registers */ |
| {E1000_ICR, "ICR"}, |
| |
| /* RX Registers */ |
| {E1000_RCTL, "RCTL"}, |
| {E1000_RDLEN(0), "RDLEN"}, |
| {E1000_RDH(0), "RDH"}, |
| {E1000_RDT(0), "RDT"}, |
| {E1000_RXDCTL(0), "RXDCTL"}, |
| {E1000_RDBAL(0), "RDBAL"}, |
| {E1000_RDBAH(0), "RDBAH"}, |
| |
| /* TX Registers */ |
| {E1000_TCTL, "TCTL"}, |
| {E1000_TDBAL(0), "TDBAL"}, |
| {E1000_TDBAH(0), "TDBAH"}, |
| {E1000_TDLEN(0), "TDLEN"}, |
| {E1000_TDH(0), "TDH"}, |
| {E1000_TDT(0), "TDT"}, |
| {E1000_TXDCTL(0), "TXDCTL"}, |
| {E1000_TDFH, "TDFH"}, |
| {E1000_TDFT, "TDFT"}, |
| {E1000_TDFHS, "TDFHS"}, |
| {E1000_TDFPC, "TDFPC"}, |
| |
| /* List Terminator */ |
| {} |
| }; |
| |
| /* igb_regdump - register printout routine */ |
| static void igb_regdump(struct e1000_hw *hw, struct igb_reg_info *reginfo) |
| { |
| int n = 0; |
| char rname[16]; |
| u32 regs[8]; |
| |
| switch (reginfo->ofs) { |
| case E1000_RDLEN(0): |
| for (n = 0; n < 4; n++) |
| regs[n] = rd32(E1000_RDLEN(n)); |
| break; |
| case E1000_RDH(0): |
| for (n = 0; n < 4; n++) |
| regs[n] = rd32(E1000_RDH(n)); |
| break; |
| case E1000_RDT(0): |
| for (n = 0; n < 4; n++) |
| regs[n] = rd32(E1000_RDT(n)); |
| break; |
| case E1000_RXDCTL(0): |
| for (n = 0; n < 4; n++) |
| regs[n] = rd32(E1000_RXDCTL(n)); |
| break; |
| case E1000_RDBAL(0): |
| for (n = 0; n < 4; n++) |
| regs[n] = rd32(E1000_RDBAL(n)); |
| break; |
| case E1000_RDBAH(0): |
| for (n = 0; n < 4; n++) |
| regs[n] = rd32(E1000_RDBAH(n)); |
| break; |
| case E1000_TDBAL(0): |
| for (n = 0; n < 4; n++) |
| regs[n] = rd32(E1000_TDBAL(n)); |
| break; |
| case E1000_TDBAH(0): |
| for (n = 0; n < 4; n++) |
| regs[n] = rd32(E1000_TDBAH(n)); |
| break; |
| case E1000_TDLEN(0): |
| for (n = 0; n < 4; n++) |
| regs[n] = rd32(E1000_TDLEN(n)); |
| break; |
| case E1000_TDH(0): |
| for (n = 0; n < 4; n++) |
| regs[n] = rd32(E1000_TDH(n)); |
| break; |
| case E1000_TDT(0): |
| for (n = 0; n < 4; n++) |
| regs[n] = rd32(E1000_TDT(n)); |
| break; |
| case E1000_TXDCTL(0): |
| for (n = 0; n < 4; n++) |
| regs[n] = rd32(E1000_TXDCTL(n)); |
| break; |
| default: |
| pr_info("%-15s %08x\n", reginfo->name, rd32(reginfo->ofs)); |
| return; |
| } |
| |
| snprintf(rname, 16, "%s%s", reginfo->name, "[0-3]"); |
| pr_info("%-15s %08x %08x %08x %08x\n", rname, regs[0], regs[1], |
| regs[2], regs[3]); |
| } |
| |
| /* igb_dump - Print registers, Tx-rings and Rx-rings */ |
| static void igb_dump(struct igb_adapter *adapter) |
| { |
| struct net_device *netdev = adapter->netdev; |
| struct e1000_hw *hw = &adapter->hw; |
| struct igb_reg_info *reginfo; |
| struct igb_ring *tx_ring; |
| union e1000_adv_tx_desc *tx_desc; |
| struct my_u0 { __le64 a; __le64 b; } *u0; |
| struct igb_ring *rx_ring; |
| union e1000_adv_rx_desc *rx_desc; |
| u32 staterr; |
| u16 i, n; |
| |
| if (!netif_msg_hw(adapter)) |
| return; |
| |
| /* Print netdevice Info */ |
| if (netdev) { |
| dev_info(&adapter->pdev->dev, "Net device Info\n"); |
| pr_info("Device Name state trans_start\n"); |
| pr_info("%-15s %016lX %016lX\n", netdev->name, |
| netdev->state, dev_trans_start(netdev)); |
| } |
| |
| /* Print Registers */ |
| dev_info(&adapter->pdev->dev, "Register Dump\n"); |
| pr_info(" Register Name Value\n"); |
| for (reginfo = (struct igb_reg_info *)igb_reg_info_tbl; |
| reginfo->name; reginfo++) { |
| igb_regdump(hw, reginfo); |
| } |
| |
| /* Print TX Ring Summary */ |
| if (!netdev || !netif_running(netdev)) |
| goto exit; |
| |
| dev_info(&adapter->pdev->dev, "TX Rings Summary\n"); |
| pr_info("Queue [NTU] [NTC] [bi(ntc)->dma ] leng ntw timestamp\n"); |
| for (n = 0; n < adapter->num_tx_queues; n++) { |
| struct igb_tx_buffer *buffer_info; |
| tx_ring = adapter->tx_ring[n]; |
| buffer_info = &tx_ring->tx_buffer_info[tx_ring->next_to_clean]; |
| pr_info(" %5d %5X %5X %016llX %04X %p %016llX\n", |
| n, tx_ring->next_to_use, tx_ring->next_to_clean, |
| (u64)dma_unmap_addr(buffer_info, dma), |
| dma_unmap_len(buffer_info, len), |
| buffer_info->next_to_watch, |
| (u64)buffer_info->time_stamp); |
| } |
| |
| /* Print TX Rings */ |
| if (!netif_msg_tx_done(adapter)) |
| goto rx_ring_summary; |
| |
| dev_info(&adapter->pdev->dev, "TX Rings Dump\n"); |
| |
| /* Transmit Descriptor Formats |
| * |
| * Advanced Transmit Descriptor |
| * +--------------------------------------------------------------+ |
| * 0 | Buffer Address [63:0] | |
| * +--------------------------------------------------------------+ |
| * 8 | PAYLEN | PORTS |CC|IDX | STA | DCMD |DTYP|MAC|RSV| DTALEN | |
| * +--------------------------------------------------------------+ |
| * 63 46 45 40 39 38 36 35 32 31 24 15 0 |
| */ |
| |
| for (n = 0; n < adapter->num_tx_queues; n++) { |
| tx_ring = adapter->tx_ring[n]; |
| pr_info("------------------------------------\n"); |
| pr_info("TX QUEUE INDEX = %d\n", tx_ring->queue_index); |
| pr_info("------------------------------------\n"); |
| pr_info("T [desc] [address 63:0 ] [PlPOCIStDDM Ln] [bi->dma ] leng ntw timestamp bi->skb\n"); |
| |
| for (i = 0; tx_ring->desc && (i < tx_ring->count); i++) { |
| const char *next_desc; |
| struct igb_tx_buffer *buffer_info; |
| tx_desc = IGB_TX_DESC(tx_ring, i); |
| buffer_info = &tx_ring->tx_buffer_info[i]; |
| u0 = (struct my_u0 *)tx_desc; |
| if (i == tx_ring->next_to_use && |
| i == tx_ring->next_to_clean) |
| next_desc = " NTC/U"; |
| else if (i == tx_ring->next_to_use) |
| next_desc = " NTU"; |
| else if (i == tx_ring->next_to_clean) |
| next_desc = " NTC"; |
| else |
| next_desc = ""; |
| |
| pr_info("T [0x%03X] %016llX %016llX %016llX %04X %p %016llX %p%s\n", |
| i, le64_to_cpu(u0->a), |
| le64_to_cpu(u0->b), |
| (u64)dma_unmap_addr(buffer_info, dma), |
| dma_unmap_len(buffer_info, len), |
| buffer_info->next_to_watch, |
| (u64)buffer_info->time_stamp, |
| buffer_info->skb, next_desc); |
| |
| if (netif_msg_pktdata(adapter) && buffer_info->skb) |
| print_hex_dump(KERN_INFO, "", |
| DUMP_PREFIX_ADDRESS, |
| 16, 1, buffer_info->skb->data, |
| dma_unmap_len(buffer_info, len), |
| true); |
| } |
| } |
| |
| /* Print RX Rings Summary */ |
| rx_ring_summary: |
| dev_info(&adapter->pdev->dev, "RX Rings Summary\n"); |
| pr_info("Queue [NTU] [NTC]\n"); |
| for (n = 0; n < adapter->num_rx_queues; n++) { |
| rx_ring = adapter->rx_ring[n]; |
| pr_info(" %5d %5X %5X\n", |
| n, rx_ring->next_to_use, rx_ring->next_to_clean); |
| } |
| |
| /* Print RX Rings */ |
| if (!netif_msg_rx_status(adapter)) |
| goto exit; |
| |
| dev_info(&adapter->pdev->dev, "RX Rings Dump\n"); |
| |
| /* Advanced Receive Descriptor (Read) Format |
| * 63 1 0 |
| * +-----------------------------------------------------+ |
| * 0 | Packet Buffer Address [63:1] |A0/NSE| |
| * +----------------------------------------------+------+ |
| * 8 | Header Buffer Address [63:1] | DD | |
| * +-----------------------------------------------------+ |
| * |
| * |
| * Advanced Receive Descriptor (Write-Back) Format |
| * |
| * 63 48 47 32 31 30 21 20 17 16 4 3 0 |
| * +------------------------------------------------------+ |
| * 0 | Packet IP |SPH| HDR_LEN | RSV|Packet| RSS | |
| * | Checksum Ident | | | | Type | Type | |
| * +------------------------------------------------------+ |
| * 8 | VLAN Tag | Length | Extended Error | Extended Status | |
| * +------------------------------------------------------+ |
| * 63 48 47 32 31 20 19 0 |
| */ |
| |
| for (n = 0; n < adapter->num_rx_queues; n++) { |
| rx_ring = adapter->rx_ring[n]; |
| pr_info("------------------------------------\n"); |
| pr_info("RX QUEUE INDEX = %d\n", rx_ring->queue_index); |
| pr_info("------------------------------------\n"); |
| pr_info("R [desc] [ PktBuf A0] [ HeadBuf DD] [bi->dma ] [bi->skb] <-- Adv Rx Read format\n"); |
| pr_info("RWB[desc] [PcsmIpSHl PtRs] [vl er S cks ln] ---------------- [bi->skb] <-- Adv Rx Write-Back format\n"); |
| |
| for (i = 0; i < rx_ring->count; i++) { |
| const char *next_desc; |
| struct igb_rx_buffer *buffer_info; |
| buffer_info = &rx_ring->rx_buffer_info[i]; |
| rx_desc = IGB_RX_DESC(rx_ring, i); |
| u0 = (struct my_u0 *)rx_desc; |
| staterr = le32_to_cpu(rx_desc->wb.upper.status_error); |
| |
| if (i == rx_ring->next_to_use) |
| next_desc = " NTU"; |
| else if (i == rx_ring->next_to_clean) |
| next_desc = " NTC"; |
| else |
| next_desc = ""; |
| |
| if (staterr & E1000_RXD_STAT_DD) { |
| /* Descriptor Done */ |
| pr_info("%s[0x%03X] %016llX %016llX ---------------- %s\n", |
| "RWB", i, |
| le64_to_cpu(u0->a), |
| le64_to_cpu(u0->b), |
| next_desc); |
| } else { |
| pr_info("%s[0x%03X] %016llX %016llX %016llX %s\n", |
| "R ", i, |
| le64_to_cpu(u0->a), |
| le64_to_cpu(u0->b), |
| (u64)buffer_info->dma, |
| next_desc); |
| |
| if (netif_msg_pktdata(adapter) && |
| buffer_info->dma && buffer_info->page) { |
| print_hex_dump(KERN_INFO, "", |
| DUMP_PREFIX_ADDRESS, |
| 16, 1, |
| page_address(buffer_info->page) + |
| buffer_info->page_offset, |
| igb_rx_bufsz(rx_ring), true); |
| } |
| } |
| } |
| } |
| |
| exit: |
| return; |
| } |
| |
| /** |
| * igb_get_i2c_data - Reads the I2C SDA data bit |
| * @data: opaque pointer to adapter struct |
| * |
| * Returns the I2C data bit value |
| **/ |
| static int igb_get_i2c_data(void *data) |
| { |
| struct igb_adapter *adapter = (struct igb_adapter *)data; |
| struct e1000_hw *hw = &adapter->hw; |
| s32 i2cctl = rd32(E1000_I2CPARAMS); |
| |
| return !!(i2cctl & E1000_I2C_DATA_IN); |
| } |
| |
| /** |
| * igb_set_i2c_data - Sets the I2C data bit |
| * @data: pointer to hardware structure |
| * @state: I2C data value (0 or 1) to set |
| * |
| * Sets the I2C data bit |
| **/ |
| static void igb_set_i2c_data(void *data, int state) |
| { |
| struct igb_adapter *adapter = (struct igb_adapter *)data; |
| struct e1000_hw *hw = &adapter->hw; |
| s32 i2cctl = rd32(E1000_I2CPARAMS); |
| |
| if (state) { |
| i2cctl |= E1000_I2C_DATA_OUT | E1000_I2C_DATA_OE_N; |
| } else { |
| i2cctl &= ~E1000_I2C_DATA_OE_N; |
| i2cctl &= ~E1000_I2C_DATA_OUT; |
| } |
| |
| wr32(E1000_I2CPARAMS, i2cctl); |
| wrfl(); |
| } |
| |
| /** |
| * igb_set_i2c_clk - Sets the I2C SCL clock |
| * @data: pointer to hardware structure |
| * @state: state to set clock |
| * |
| * Sets the I2C clock line to state |
| **/ |
| static void igb_set_i2c_clk(void *data, int state) |
| { |
| struct igb_adapter *adapter = (struct igb_adapter *)data; |
| struct e1000_hw *hw = &adapter->hw; |
| s32 i2cctl = rd32(E1000_I2CPARAMS); |
| |
| if (state) { |
| i2cctl |= E1000_I2C_CLK_OUT | E1000_I2C_CLK_OE_N; |
| } else { |
| i2cctl &= ~E1000_I2C_CLK_OUT; |
| i2cctl &= ~E1000_I2C_CLK_OE_N; |
| } |
| wr32(E1000_I2CPARAMS, i2cctl); |
| wrfl(); |
| } |
| |
| /** |
| * igb_get_i2c_clk - Gets the I2C SCL clock state |
| * @data: pointer to hardware structure |
| * |
| * Gets the I2C clock state |
| **/ |
| static int igb_get_i2c_clk(void *data) |
| { |
| struct igb_adapter *adapter = (struct igb_adapter *)data; |
| struct e1000_hw *hw = &adapter->hw; |
| s32 i2cctl = rd32(E1000_I2CPARAMS); |
| |
| return !!(i2cctl & E1000_I2C_CLK_IN); |
| } |
| |
| static const struct i2c_algo_bit_data igb_i2c_algo = { |
| .setsda = igb_set_i2c_data, |
| .setscl = igb_set_i2c_clk, |
| .getsda = igb_get_i2c_data, |
| .getscl = igb_get_i2c_clk, |
| .udelay = 5, |
| .timeout = 20, |
| }; |
| |
| /** |
| * igb_get_hw_dev - return device |
| * @hw: pointer to hardware structure |
| * |
| * used by hardware layer to print debugging information |
| **/ |
| struct net_device *igb_get_hw_dev(struct e1000_hw *hw) |
| { |
| struct igb_adapter *adapter = hw->back; |
| return adapter->netdev; |
| } |
| |
| static struct pci_driver igb_driver; |
| |
| /** |
| * igb_init_module - Driver Registration Routine |
| * |
| * igb_init_module is the first routine called when the driver is |
| * loaded. All it does is register with the PCI subsystem. |
| **/ |
| static int __init igb_init_module(void) |
| { |
| int ret; |
| |
| pr_info("%s\n", igb_driver_string); |
| pr_info("%s\n", igb_copyright); |
| |
| #ifdef CONFIG_IGB_DCA |
| dca_register_notify(&dca_notifier); |
| #endif |
| ret = pci_register_driver(&igb_driver); |
| return ret; |
| } |
| |
| module_init(igb_init_module); |
| |
| /** |
| * igb_exit_module - Driver Exit Cleanup Routine |
| * |
| * igb_exit_module is called just before the driver is removed |
| * from memory. |
| **/ |
| static void __exit igb_exit_module(void) |
| { |
| #ifdef CONFIG_IGB_DCA |
| dca_unregister_notify(&dca_notifier); |
| #endif |
| pci_unregister_driver(&igb_driver); |
| } |
| |
| module_exit(igb_exit_module); |
| |
| #define Q_IDX_82576(i) (((i & 0x1) << 3) + (i >> 1)) |
| /** |
| * igb_cache_ring_register - Descriptor ring to register mapping |
| * @adapter: board private structure to initialize |
| * |
| * Once we know the feature-set enabled for the device, we'll cache |
| * the register offset the descriptor ring is assigned to. |
| **/ |
| static void igb_cache_ring_register(struct igb_adapter *adapter) |
| { |
| int i = 0, j = 0; |
| u32 rbase_offset = adapter->vfs_allocated_count; |
| |
| switch (adapter->hw.mac.type) { |
| case e1000_82576: |
| /* The queues are allocated for virtualization such that VF 0 |
| * is allocated queues 0 and 8, VF 1 queues 1 and 9, etc. |
| * In order to avoid collision we start at the first free queue |
| * and continue consuming queues in the same sequence |
| */ |
| if (adapter->vfs_allocated_count) { |
| for (; i < adapter->rss_queues; i++) |
| adapter->rx_ring[i]->reg_idx = rbase_offset + |
| Q_IDX_82576(i); |
| } |
| fallthrough; |
| case e1000_82575: |
| case e1000_82580: |
| case e1000_i350: |
| case e1000_i354: |
| case e1000_i210: |
| case e1000_i211: |
| default: |
| for (; i < adapter->num_rx_queues; i++) |
| adapter->rx_ring[i]->reg_idx = rbase_offset + i; |
| for (; j < adapter->num_tx_queues; j++) |
| adapter->tx_ring[j]->reg_idx = rbase_offset + j; |
| break; |
| } |
| } |
| |
| u32 igb_rd32(struct e1000_hw *hw, u32 reg) |
| { |
| struct igb_adapter *igb = container_of(hw, struct igb_adapter, hw); |
| u8 __iomem *hw_addr = READ_ONCE(hw->hw_addr); |
| u32 value = 0; |
| |
| if (E1000_REMOVED(hw_addr)) |
| return ~value; |
| |
| value = readl(&hw_addr[reg]); |
| |
| /* reads should not return all F's */ |
| if (!(~value) && (!reg || !(~readl(hw_addr)))) { |
| struct net_device *netdev = igb->netdev; |
| hw->hw_addr = NULL; |
| netdev_err(netdev, "PCIe link lost\n"); |
| WARN(pci_device_is_present(igb->pdev), |
| "igb: Failed to read reg 0x%x!\n", reg); |
| } |
| |
| return value; |
| } |
| |
| /** |
| * igb_write_ivar - configure ivar for given MSI-X vector |
| * @hw: pointer to the HW structure |
| * @msix_vector: vector number we are allocating to a given ring |
| * @index: row index of IVAR register to write within IVAR table |
| * @offset: column offset of in IVAR, should be multiple of 8 |
| * |
| * This function is intended to handle the writing of the IVAR register |
| * for adapters 82576 and newer. The IVAR table consists of 2 columns, |
| * each containing an cause allocation for an Rx and Tx ring, and a |
| * variable number of rows depending on the number of queues supported. |
| **/ |
| static void igb_write_ivar(struct e1000_hw *hw, int msix_vector, |
| int index, int offset) |
| { |
| u32 ivar = array_rd32(E1000_IVAR0, index); |
| |
| /* clear any bits that are currently set */ |
| ivar &= ~((u32)0xFF << offset); |
| |
| /* write vector and valid bit */ |
| ivar |= (msix_vector | E1000_IVAR_VALID) << offset; |
| |
| array_wr32(E1000_IVAR0, index, ivar); |
| } |
| |
| #define IGB_N0_QUEUE -1 |
| static void igb_assign_vector(struct igb_q_vector *q_vector, int msix_vector) |
| { |
| struct igb_adapter *adapter = q_vector->adapter; |
| struct e1000_hw *hw = &adapter->hw; |
| int rx_queue = IGB_N0_QUEUE; |
| int tx_queue = IGB_N0_QUEUE; |
| u32 msixbm = 0; |
| |
| if (q_vector->rx.ring) |
| rx_queue = q_vector->rx.ring->reg_idx; |
| if (q_vector->tx.ring) |
| tx_queue = q_vector->tx.ring->reg_idx; |
| |
| switch (hw->mac.type) { |
| case e1000_82575: |
| /* The 82575 assigns vectors using a bitmask, which matches the |
| * bitmask for the EICR/EIMS/EIMC registers. To assign one |
| * or more queues to a vector, we write the appropriate bits |
| * into the MSIXBM register for that vector. |
| */ |
| if (rx_queue > IGB_N0_QUEUE) |
| msixbm = E1000_EICR_RX_QUEUE0 << rx_queue; |
| if (tx_queue > IGB_N0_QUEUE) |
| msixbm |= E1000_EICR_TX_QUEUE0 << tx_queue; |
| if (!(adapter->flags & IGB_FLAG_HAS_MSIX) && msix_vector == 0) |
| msixbm |= E1000_EIMS_OTHER; |
| array_wr32(E1000_MSIXBM(0), msix_vector, msixbm); |
| q_vector->eims_value = msixbm; |
| break; |
| case e1000_82576: |
| /* 82576 uses a table that essentially consists of 2 columns |
| * with 8 rows. The ordering is column-major so we use the |
| * lower 3 bits as the row index, and the 4th bit as the |
| * column offset. |
| */ |
| if (rx_queue > IGB_N0_QUEUE) |
| igb_write_ivar(hw, msix_vector, |
| rx_queue & 0x7, |
| (rx_queue & 0x8) << 1); |
| if (tx_queue > IGB_N0_QUEUE) |
| igb_write_ivar(hw, msix_vector, |
| tx_queue & 0x7, |
| ((tx_queue & 0x8) << 1) + 8); |
| q_vector->eims_value = BIT(msix_vector); |
| break; |
| case e1000_82580: |
| case e1000_i350: |
| case e1000_i354: |
| case e1000_i210: |
| case e1000_i211: |
| /* On 82580 and newer adapters the scheme is similar to 82576 |
| * however instead of ordering column-major we have things |
| * ordered row-major. So we traverse the table by using |
| * bit 0 as the column offset, and the remaining bits as the |
| * row index. |
| */ |
| if (rx_queue > IGB_N0_QUEUE) |
| igb_write_ivar(hw, msix_vector, |
| rx_queue >> 1, |
| (rx_queue & 0x1) << 4); |
| if (tx_queue > IGB_N0_QUEUE) |
| igb_write_ivar(hw, msix_vector, |
| tx_queue >> 1, |
| ((tx_queue & 0x1) << 4) + 8); |
| q_vector->eims_value = BIT(msix_vector); |
| break; |
| default: |
| BUG(); |
| break; |
| } |
| |
| /* add q_vector eims value to global eims_enable_mask */ |
| adapter->eims_enable_mask |= q_vector->eims_value; |
| |
| /* configure q_vector to set itr on first interrupt */ |
| q_vector->set_itr = 1; |
| } |
| |
| /** |
| * igb_configure_msix - Configure MSI-X hardware |
| * @adapter: board private structure to initialize |
| * |
| * igb_configure_msix sets up the hardware to properly |
| * generate MSI-X interrupts. |
| **/ |
| static void igb_configure_msix(struct igb_adapter *adapter) |
| { |
| u32 tmp; |
| int i, vector = 0; |
| struct e1000_hw *hw = &adapter->hw; |
| |
| adapter->eims_enable_mask = 0; |
| |
| /* set vector for other causes, i.e. link changes */ |
| switch (hw->mac.type) { |
| case e1000_82575: |
| tmp = rd32(E1000_CTRL_EXT); |
| /* enable MSI-X PBA support*/ |
| tmp |= E1000_CTRL_EXT_PBA_CLR; |
| |
| /* Auto-Mask interrupts upon ICR read. */ |
| tmp |= E1000_CTRL_EXT_EIAME; |
| tmp |= E1000_CTRL_EXT_IRCA; |
| |
| wr32(E1000_CTRL_EXT, tmp); |
| |
| /* enable msix_other interrupt */ |
| array_wr32(E1000_MSIXBM(0), vector++, E1000_EIMS_OTHER); |
| adapter->eims_other = E1000_EIMS_OTHER; |
| |
| break; |
| |
| case e1000_82576: |
| case e1000_82580: |
| case e1000_i350: |
| case e1000_i354: |
| case e1000_i210: |
| case e1000_i211: |
| /* Turn on MSI-X capability first, or our settings |
| * won't stick. And it will take days to debug. |
| */ |
| wr32(E1000_GPIE, E1000_GPIE_MSIX_MODE | |
| E1000_GPIE_PBA | E1000_GPIE_EIAME | |
| E1000_GPIE_NSICR); |
| |
| /* enable msix_other interrupt */ |
| adapter->eims_other = BIT(vector); |
| tmp = (vector++ | E1000_IVAR_VALID) << 8; |
| |
| wr32(E1000_IVAR_MISC, tmp); |
| break; |
| default: |
| /* do nothing, since nothing else supports MSI-X */ |
| break; |
| } /* switch (hw->mac.type) */ |
| |
| adapter->eims_enable_mask |= adapter->eims_other; |
| |
| for (i = 0; i < adapter->num_q_vectors; i++) |
| igb_assign_vector(adapter->q_vector[i], vector++); |
| |
| wrfl(); |
| } |
| |
| /** |
| * igb_request_msix - Initialize MSI-X interrupts |
| * @adapter: board private structure to initialize |
| * |
| * igb_request_msix allocates MSI-X vectors and requests interrupts from the |
| * kernel. |
| **/ |
| static int igb_request_msix(struct igb_adapter *adapter) |
| { |
| unsigned int num_q_vectors = adapter->num_q_vectors; |
| struct net_device *netdev = adapter->netdev; |
| int i, err = 0, vector = 0, free_vector = 0; |
| |
| err = request_irq(adapter->msix_entries[vector].vector, |
| igb_msix_other, 0, netdev->name, adapter); |
| if (err) |
| goto err_out; |
| |
| if (num_q_vectors > MAX_Q_VECTORS) { |
| num_q_vectors = MAX_Q_VECTORS; |
| dev_warn(&adapter->pdev->dev, |
| "The number of queue vectors (%d) is higher than max allowed (%d)\n", |
| adapter->num_q_vectors, MAX_Q_VECTORS); |
| } |
| for (i = 0; i < num_q_vectors; i++) { |
| struct igb_q_vector *q_vector = adapter->q_vector[i]; |
| |
| vector++; |
| |
| q_vector->itr_register = adapter->io_addr + E1000_EITR(vector); |
| |
| if (q_vector->rx.ring && q_vector->tx.ring) |
| sprintf(q_vector->name, "%s-TxRx-%u", netdev->name, |
| q_vector->rx.ring->queue_index); |
| else if (q_vector->tx.ring) |
| sprintf(q_vector->name, "%s-tx-%u", netdev->name, |
| q_vector->tx.ring->queue_index); |
| else if (q_vector->rx.ring) |
| sprintf(q_vector->name, "%s-rx-%u", netdev->name, |
| q_vector->rx.ring->queue_index); |
| else |
| sprintf(q_vector->name, "%s-unused", netdev->name); |
| |
| err = request_irq(adapter->msix_entries[vector].vector, |
| igb_msix_ring, 0, q_vector->name, |
| q_vector); |
| if (err) |
| goto err_free; |
| } |
| |
| igb_configure_msix(adapter); |
| return 0; |
| |
| err_free: |
| /* free already assigned IRQs */ |
| free_irq(adapter->msix_entries[free_vector++].vector, adapter); |
| |
| vector--; |
| for (i = 0; i < vector; i++) { |
| free_irq(adapter->msix_entries[free_vector++].vector, |
| adapter->q_vector[i]); |
| } |
| err_out: |
| return err; |
| } |
| |
| /** |
| * igb_free_q_vector - Free memory allocated for specific interrupt vector |
| * @adapter: board private structure to initialize |
| * @v_idx: Index of vector to be freed |
| * |
| * This function frees the memory allocated to the q_vector. |
| **/ |
| static void igb_free_q_vector(struct igb_adapter *adapter, int v_idx) |
| { |
| struct igb_q_vector *q_vector = adapter->q_vector[v_idx]; |
| |
| adapter->q_vector[v_idx] = NULL; |
| |
| /* igb_get_stats64() might access the rings on this vector, |
| * we must wait a grace period before freeing it. |
| */ |
| if (q_vector) |
| kfree_rcu(q_vector, rcu); |
| } |
| |
| /** |
| * igb_reset_q_vector - Reset config for interrupt vector |
| * @adapter: board private structure to initialize |
| * @v_idx: Index of vector to be reset |
| * |
| * If NAPI is enabled it will delete any references to the |
| * NAPI struct. This is preparation for igb_free_q_vector. |
| **/ |
| static void igb_reset_q_vector(struct igb_adapter *adapter, int v_idx) |
| { |
| struct igb_q_vector *q_vector = adapter->q_vector[v_idx]; |
| |
| /* Coming from igb_set_interrupt_capability, the vectors are not yet |
| * allocated. So, q_vector is NULL so we should stop here. |
| */ |
| if (!q_vector) |
| return; |
| |
| if (q_vector->tx.ring) |
| adapter->tx_ring[q_vector->tx.ring->queue_index] = NULL; |
| |
| if (q_vector->rx.ring) |
| adapter->rx_ring[q_vector->rx.ring->queue_index] = NULL; |
| |
| netif_napi_del(&q_vector->napi); |
| |
| } |
| |
| static void igb_reset_interrupt_capability(struct igb_adapter *adapter) |
| { |
| int v_idx = adapter->num_q_vectors; |
| |
| if (adapter->flags & IGB_FLAG_HAS_MSIX) |
| pci_disable_msix(adapter->pdev); |
| else if (adapter->flags & IGB_FLAG_HAS_MSI) |
| pci_disable_msi(adapter->pdev); |
| |
| while (v_idx--) |
| igb_reset_q_vector(adapter, v_idx); |
| } |
| |
| /** |
| * igb_free_q_vectors - Free memory allocated for interrupt vectors |
| * @adapter: board private structure to initialize |
| * |
| * This function frees the memory allocated to the q_vectors. In addition if |
| * NAPI is enabled it will delete any references to the NAPI struct prior |
| * to freeing the q_vector. |
| **/ |
| static void igb_free_q_vectors(struct igb_adapter *adapter) |
| { |
| int v_idx = adapter->num_q_vectors; |
| |
| adapter->num_tx_queues = 0; |
| adapter->num_rx_queues = 0; |
| adapter->num_q_vectors = 0; |
| |
| while (v_idx--) { |
| igb_reset_q_vector(adapter, v_idx); |
| igb_free_q_vector(adapter, v_idx); |
| } |
| } |
| |
| /** |
| * igb_clear_interrupt_scheme - reset the device to a state of no interrupts |
| * @adapter: board private structure to initialize |
| * |
| * This function resets the device so that it has 0 Rx queues, Tx queues, and |
| * MSI-X interrupts allocated. |
| */ |
| static void igb_clear_interrupt_scheme(struct igb_adapter *adapter) |
| { |
| igb_free_q_vectors(adapter); |
| igb_reset_interrupt_capability(adapter); |
| } |
| |
| /** |
| * igb_set_interrupt_capability - set MSI or MSI-X if supported |
| * @adapter: board private structure to initialize |
| * @msix: boolean value of MSIX capability |
| * |
| * Attempt to configure interrupts using the best available |
| * capabilities of the hardware and kernel. |
| **/ |
| static void igb_set_interrupt_capability(struct igb_adapter *adapter, bool msix) |
| { |
| int err; |
| int numvecs, i; |
| |
| if (!msix) |
| goto msi_only; |
| adapter->flags |= IGB_FLAG_HAS_MSIX; |
| |
| /* Number of supported queues. */ |
| adapter->num_rx_queues = adapter->rss_queues; |
| if (adapter->vfs_allocated_count) |
| adapter->num_tx_queues = 1; |
| else |
| adapter->num_tx_queues = adapter->rss_queues; |
| |
| /* start with one vector for every Rx queue */ |
| numvecs = adapter->num_rx_queues; |
| |
| /* if Tx handler is separate add 1 for every Tx queue */ |
| if (!(adapter->flags & IGB_FLAG_QUEUE_PAIRS)) |
| numvecs += adapter->num_tx_queues; |
| |
| /* store the number of vectors reserved for queues */ |
| adapter->num_q_vectors = numvecs; |
| |
| /* add 1 vector for link status interrupts */ |
| numvecs++; |
| for (i = 0; i < numvecs; i++) |
| adapter->msix_entries[i].entry = i; |
| |
| err = pci_enable_msix_range(adapter->pdev, |
| adapter->msix_entries, |
| numvecs, |
| numvecs); |
| if (err > 0) |
| return; |
| |
| igb_reset_interrupt_capability(adapter); |
| |
| /* If we can't do MSI-X, try MSI */ |
| msi_only: |
| adapter->flags &= ~IGB_FLAG_HAS_MSIX; |
| #ifdef CONFIG_PCI_IOV |
| /* disable SR-IOV for non MSI-X configurations */ |
| if (adapter->vf_data) { |
| struct e1000_hw *hw = &adapter->hw; |
| /* disable iov and allow time for transactions to clear */ |
| pci_disable_sriov(adapter->pdev); |
| msleep(500); |
| |
| kfree(adapter->vf_mac_list); |
| adapter->vf_mac_list = NULL; |
| kfree(adapter->vf_data); |
| adapter->vf_data = NULL; |
| wr32(E1000_IOVCTL, E1000_IOVCTL_REUSE_VFQ); |
| wrfl(); |
| msleep(100); |
| dev_info(&adapter->pdev->dev, "IOV Disabled\n"); |
| } |
| #endif |
| adapter->vfs_allocated_count = 0; |
| adapter->rss_queues = 1; |
| adapter->flags |= IGB_FLAG_QUEUE_PAIRS; |
| adapter->num_rx_queues = 1; |
| adapter->num_tx_queues = 1; |
| adapter->num_q_vectors = 1; |
| if (!pci_enable_msi(adapter->pdev)) |
| adapter->flags |= IGB_FLAG_HAS_MSI; |
| } |
| |
| static void igb_add_ring(struct igb_ring *ring, |
| struct igb_ring_container *head) |
| { |
| head->ring = ring; |
| head->count++; |
| } |
| |
| /** |
| * igb_alloc_q_vector - Allocate memory for a single interrupt vector |
| * @adapter: board private structure to initialize |
| * @v_count: q_vectors allocated on adapter, used for ring interleaving |
| * @v_idx: index of vector in adapter struct |
| * @txr_count: total number of Tx rings to allocate |
| * @txr_idx: index of first Tx ring to allocate |
| * @rxr_count: total number of Rx rings to allocate |
| * @rxr_idx: index of first Rx ring to allocate |
| * |
| * We allocate one q_vector. If allocation fails we return -ENOMEM. |
| **/ |
| static int igb_alloc_q_vector(struct igb_adapter *adapter, |
| int v_count, int v_idx, |
| int txr_count, int txr_idx, |
| int rxr_count, int rxr_idx) |
| { |
| struct igb_q_vector *q_vector; |
| struct igb_ring *ring; |
| int ring_count; |
| size_t size; |
| |
| /* igb only supports 1 Tx and/or 1 Rx queue per vector */ |
| if (txr_count > 1 || rxr_count > 1) |
| return -ENOMEM; |
| |
| ring_count = txr_count + rxr_count; |
| size = kmalloc_size_roundup(struct_size(q_vector, ring, ring_count)); |
| |
| /* allocate q_vector and rings */ |
| q_vector = adapter->q_vector[v_idx]; |
| if (!q_vector) { |
| q_vector = kzalloc(size, GFP_KERNEL); |
| } else if (size > ksize(q_vector)) { |
| struct igb_q_vector *new_q_vector; |
| |
| new_q_vector = kzalloc(size, GFP_KERNEL); |
| if (new_q_vector) |
| kfree_rcu(q_vector, rcu); |
| q_vector = new_q_vector; |
| } else { |
| memset(q_vector, 0, size); |
| } |
| if (!q_vector) |
| return -ENOMEM; |
| |
| /* initialize NAPI */ |
| netif_napi_add(adapter->netdev, &q_vector->napi, igb_poll); |
| |
| /* tie q_vector and adapter together */ |
| adapter->q_vector[v_idx] = q_vector; |
| q_vector->adapter = adapter; |
| |
| /* initialize work limits */ |
| q_vector->tx.work_limit = adapter->tx_work_limit; |
| |
| /* initialize ITR configuration */ |
| q_vector->itr_register = adapter->io_addr + E1000_EITR(0); |
| q_vector->itr_val = IGB_START_ITR; |
| |
| /* initialize pointer to rings */ |
| ring = q_vector->ring; |
| |
| /* intialize ITR */ |
| if (rxr_count) { |
| /* rx or rx/tx vector */ |
| if (!adapter->rx_itr_setting || adapter->rx_itr_setting > 3) |
| q_vector->itr_val = adapter->rx_itr_setting; |
| } else { |
| /* tx only vector */ |
| if (!adapter->tx_itr_setting || adapter->tx_itr_setting > 3) |
| q_vector->itr_val = adapter->tx_itr_setting; |
| } |
| |
| if (txr_count) { |
| /* assign generic ring traits */ |
| ring->dev = &adapter->pdev->dev; |
| ring->netdev = adapter->netdev; |
| |
| /* configure backlink on ring */ |
| ring->q_vector = q_vector; |
| |
| /* update q_vector Tx values */ |
| igb_add_ring(ring, &q_vector->tx); |
| |
| /* For 82575, context index must be unique per ring. */ |
| if (adapter->hw.mac.type == e1000_82575) |
| set_bit(IGB_RING_FLAG_TX_CTX_IDX, &ring->flags); |
| |
| /* apply Tx specific ring traits */ |
| ring->count = adapter->tx_ring_count; |
| ring->queue_index = txr_idx; |
| |
| ring->cbs_enable = false; |
| ring->idleslope = 0; |
| ring->sendslope = 0; |
| ring->hicredit = 0; |
| ring->locredit = 0; |
| |
| u64_stats_init(&ring->tx_syncp); |
| u64_stats_init(&ring->tx_syncp2); |
| |
| /* assign ring to adapter */ |
| adapter->tx_ring[txr_idx] = ring; |
| |
| /* push pointer to next ring */ |
| ring++; |
| } |
| |
| if (rxr_count) { |
| /* assign generic ring traits */ |
| ring->dev = &adapter->pdev->dev; |
| ring->netdev = adapter->netdev; |
| |
| /* configure backlink on ring */ |
| ring->q_vector = q_vector; |
| |
| /* update q_vector Rx values */ |
| igb_add_ring(ring, &q_vector->rx); |
| |
| /* set flag indicating ring supports SCTP checksum offload */ |
| if (adapter->hw.mac.type >= e1000_82576) |
| set_bit(IGB_RING_FLAG_RX_SCTP_CSUM, &ring->flags); |
| |
| /* On i350, i354, i210, and i211, loopback VLAN packets |
| * have the tag byte-swapped. |
| */ |
| if (adapter->hw.mac.type >= e1000_i350) |
| set_bit(IGB_RING_FLAG_RX_LB_VLAN_BSWAP, &ring->flags); |
| |
| /* apply Rx specific ring traits */ |
| ring->count = adapter->rx_ring_count; |
| ring->queue_index = rxr_idx; |
| |
| u64_stats_init(&ring->rx_syncp); |
| |
| /* assign ring to adapter */ |
| adapter->rx_ring[rxr_idx] = ring; |
| } |
| |
| return 0; |
| } |
| |
| |
| /** |
| * igb_alloc_q_vectors - Allocate memory for interrupt vectors |
| * @adapter: board private structure to initialize |
| * |
| * We allocate one q_vector per queue interrupt. If allocation fails we |
| * return -ENOMEM. |
| **/ |
| static int igb_alloc_q_vectors(struct igb_adapter *adapter) |
| { |
| int q_vectors = adapter->num_q_vectors; |
| int rxr_remaining = adapter->num_rx_queues; |
| int txr_remaining = adapter->num_tx_queues; |
| int rxr_idx = 0, txr_idx = 0, v_idx = 0; |
| int err; |
| |
| if (q_vectors >= (rxr_remaining + txr_remaining)) { |
| for (; rxr_remaining; v_idx++) { |
| err = igb_alloc_q_vector(adapter, q_vectors, v_idx, |
| 0, 0, 1, rxr_idx); |
| |
| if (err) |
| goto err_out; |
| |
| /* update counts and index */ |
| rxr_remaining--; |
| rxr_idx++; |
| } |
| } |
| |
| for (; v_idx < q_vectors; v_idx++) { |
| int rqpv = DIV_ROUND_UP(rxr_remaining, q_vectors - v_idx); |
| int tqpv = DIV_ROUND_UP(txr_remaining, q_vectors - v_idx); |
| |
| err = igb_alloc_q_vector(adapter, q_vectors, v_idx, |
| tqpv, txr_idx, rqpv, rxr_idx); |
| |
| if (err) |
| goto err_out; |
| |
| /* update counts and index */ |
| rxr_remaining -= rqpv; |
| txr_remaining -= tqpv; |
| rxr_idx++; |
| txr_idx++; |
| } |
| |
| return 0; |
| |
| err_out: |
| adapter->num_tx_queues = 0; |
| adapter->num_rx_queues = 0; |
| adapter->num_q_vectors = 0; |
| |
| while (v_idx--) |
| igb_free_q_vector(adapter, v_idx); |
| |
| return -ENOMEM; |
| } |
| |
| /** |
| * igb_init_interrupt_scheme - initialize interrupts, allocate queues/vectors |
| * @adapter: board private structure to initialize |
| * @msix: boolean value of MSIX capability |
| * |
| * This function initializes the interrupts and allocates all of the queues. |
| **/ |
| static int igb_init_interrupt_scheme(struct igb_adapter *adapter, bool msix) |
| { |
| struct pci_dev *pdev = adapter->pdev; |
| int err; |
| |
| igb_set_interrupt_capability(adapter, msix); |
| |
| err = igb_alloc_q_vectors(adapter); |
| if (err) { |
| dev_err(&pdev->dev, "Unable to allocate memory for vectors\n"); |
| goto err_alloc_q_vectors; |
| } |
| |
| igb_cache_ring_register(adapter); |
| |
| return 0; |
| |
| err_alloc_q_vectors: |
| igb_reset_interrupt_capability(adapter); |
| return err; |
| } |
| |
| /** |
| * igb_request_irq - initialize interrupts |
| * @adapter: board private structure to initialize |
| * |
| * Attempts to configure interrupts using the best available |
| * capabilities of the hardware and kernel. |
| **/ |
| static int igb_request_irq(struct igb_adapter *adapter) |
| { |
| struct net_device *netdev = adapter->netdev; |
| struct pci_dev *pdev = adapter->pdev; |
| int err = 0; |
| |
| if (adapter->flags & IGB_FLAG_HAS_MSIX) { |
| err = igb_request_msix(adapter); |
| if (!err) |
| goto request_done; |
| /* fall back to MSI */ |
| igb_free_all_tx_resources(adapter); |
| igb_free_all_rx_resources(adapter); |
| |
| igb_clear_interrupt_scheme(adapter); |
| err = igb_init_interrupt_scheme(adapter, false); |
| if (err) |
| goto request_done; |
| |
| igb_setup_all_tx_resources(adapter); |
| igb_setup_all_rx_resources(adapter); |
| igb_configure(adapter); |
| } |
| |
| igb_assign_vector(adapter->q_vector[0], 0); |
| |
| if (adapter->flags & IGB_FLAG_HAS_MSI) { |
| err = request_irq(pdev->irq, igb_intr_msi, 0, |
| netdev->name, adapter); |
| if (!err) |
| goto request_done; |
| |
| /* fall back to legacy interrupts */ |
| igb_reset_interrupt_capability(adapter); |
| adapter->flags &= ~IGB_FLAG_HAS_MSI; |
| } |
| |
| err = request_irq(pdev->irq, igb_intr, IRQF_SHARED, |
| netdev->name, adapter); |
| |
| if (err) |
| dev_err(&pdev->dev, "Error %d getting interrupt\n", |
| err); |
| |
| request_done: |
| return err; |
| } |
| |
| static void igb_free_irq(struct igb_adapter *adapter) |
| { |
| if (adapter->flags & IGB_FLAG_HAS_MSIX) { |
| int vector = 0, i; |
| |
| free_irq(adapter->msix_entries[vector++].vector, adapter); |
| |
| for (i = 0; i < adapter->num_q_vectors; i++) |
| free_irq(adapter->msix_entries[vector++].vector, |
| adapter->q_vector[i]); |
| } else { |
| free_irq(adapter->pdev->irq, adapter); |
| } |
| } |
| |
| /** |
| * igb_irq_disable - Mask off interrupt generation on the NIC |
| * @adapter: board private structure |
| **/ |
| static void igb_irq_disable(struct igb_adapter *adapter) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| |
| /* we need to be careful when disabling interrupts. The VFs are also |
| * mapped into these registers and so clearing the bits can cause |
| * issues on the VF drivers so we only need to clear what we set |
| */ |
| if (adapter->flags & IGB_FLAG_HAS_MSIX) { |
| u32 regval = rd32(E1000_EIAM); |
| |
| wr32(E1000_EIAM, regval & ~adapter->eims_enable_mask); |
| wr32(E1000_EIMC, adapter->eims_enable_mask); |
| regval = rd32(E1000_EIAC); |
| wr32(E1000_EIAC, regval & ~adapter->eims_enable_mask); |
| } |
| |
| wr32(E1000_IAM, 0); |
| wr32(E1000_IMC, ~0); |
| wrfl(); |
| if (adapter->flags & IGB_FLAG_HAS_MSIX) { |
| int i; |
| |
| for (i = 0; i < adapter->num_q_vectors; i++) |
| synchronize_irq(adapter->msix_entries[i].vector); |
| } else { |
| synchronize_irq(adapter->pdev->irq); |
| } |
| } |
| |
| /** |
| * igb_irq_enable - Enable default interrupt generation settings |
| * @adapter: board private structure |
| **/ |
| static void igb_irq_enable(struct igb_adapter *adapter) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| |
| if (adapter->flags & IGB_FLAG_HAS_MSIX) { |
| u32 ims = E1000_IMS_LSC | E1000_IMS_DOUTSYNC | E1000_IMS_DRSTA; |
| u32 regval = rd32(E1000_EIAC); |
| |
| wr32(E1000_EIAC, regval | adapter->eims_enable_mask); |
| regval = rd32(E1000_EIAM); |
| wr32(E1000_EIAM, regval | adapter->eims_enable_mask); |
| wr32(E1000_EIMS, adapter->eims_enable_mask); |
| if (adapter->vfs_allocated_count) { |
| wr32(E1000_MBVFIMR, 0xFF); |
| ims |= E1000_IMS_VMMB; |
| } |
| wr32(E1000_IMS, ims); |
| } else { |
| wr32(E1000_IMS, IMS_ENABLE_MASK | |
| E1000_IMS_DRSTA); |
| wr32(E1000_IAM, IMS_ENABLE_MASK | |
| E1000_IMS_DRSTA); |
| } |
| } |
| |
| static void igb_update_mng_vlan(struct igb_adapter *adapter) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| u16 pf_id = adapter->vfs_allocated_count; |
| u16 vid = adapter->hw.mng_cookie.vlan_id; |
| u16 old_vid = adapter->mng_vlan_id; |
| |
| if (hw->mng_cookie.status & E1000_MNG_DHCP_COOKIE_STATUS_VLAN) { |
| /* add VID to filter table */ |
| igb_vfta_set(hw, vid, pf_id, true, true); |
| adapter->mng_vlan_id = vid; |
| } else { |
| adapter->mng_vlan_id = IGB_MNG_VLAN_NONE; |
| } |
| |
| if ((old_vid != (u16)IGB_MNG_VLAN_NONE) && |
| (vid != old_vid) && |
| !test_bit(old_vid, adapter->active_vlans)) { |
| /* remove VID from filter table */ |
| igb_vfta_set(hw, vid, pf_id, false, true); |
| } |
| } |
| |
| /** |
| * igb_release_hw_control - release control of the h/w to f/w |
| * @adapter: address of board private structure |
| * |
| * igb_release_hw_control resets CTRL_EXT:DRV_LOAD bit. |
| * For ASF and Pass Through versions of f/w this means that the |
| * driver is no longer loaded. |
| **/ |
| static void igb_release_hw_control(struct igb_adapter *adapter) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| u32 ctrl_ext; |
| |
| /* Let firmware take over control of h/w */ |
| ctrl_ext = rd32(E1000_CTRL_EXT); |
| wr32(E1000_CTRL_EXT, |
| ctrl_ext & ~E1000_CTRL_EXT_DRV_LOAD); |
| } |
| |
| /** |
| * igb_get_hw_control - get control of the h/w from f/w |
| * @adapter: address of board private structure |
| * |
| * igb_get_hw_control sets CTRL_EXT:DRV_LOAD bit. |
| * For ASF and Pass Through versions of f/w this means that |
| * the driver is loaded. |
| **/ |
| static void igb_get_hw_control(struct igb_adapter *adapter) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| u32 ctrl_ext; |
| |
| /* Let firmware know the driver has taken over */ |
| ctrl_ext = rd32(E1000_CTRL_EXT); |
| wr32(E1000_CTRL_EXT, |
| ctrl_ext | E1000_CTRL_EXT_DRV_LOAD); |
| } |
| |
| static void enable_fqtss(struct igb_adapter *adapter, bool enable) |
| { |
| struct net_device *netdev = adapter->netdev; |
| struct e1000_hw *hw = &adapter->hw; |
| |
| WARN_ON(hw->mac.type != e1000_i210); |
| |
| if (enable) |
| adapter->flags |= IGB_FLAG_FQTSS; |
| else |
| adapter->flags &= ~IGB_FLAG_FQTSS; |
| |
| if (netif_running(netdev)) |
| schedule_work(&adapter->reset_task); |
| } |
| |
| static bool is_fqtss_enabled(struct igb_adapter *adapter) |
| { |
| return (adapter->flags & IGB_FLAG_FQTSS) ? true : false; |
| } |
| |
| static void set_tx_desc_fetch_prio(struct e1000_hw *hw, int queue, |
| enum tx_queue_prio prio) |
| { |
| u32 val; |
| |
| WARN_ON(hw->mac.type != e1000_i210); |
| WARN_ON(queue < 0 || queue > 4); |
| |
| val = rd32(E1000_I210_TXDCTL(queue)); |
| |
| if (prio == TX_QUEUE_PRIO_HIGH) |
| val |= E1000_TXDCTL_PRIORITY; |
| else |
| val &= ~E1000_TXDCTL_PRIORITY; |
| |
| wr32(E1000_I210_TXDCTL(queue), val); |
| } |
| |
| static void set_queue_mode(struct e1000_hw *hw, int queue, enum queue_mode mode) |
| { |
| u32 val; |
| |
| WARN_ON(hw->mac.type != e1000_i210); |
| WARN_ON(queue < 0 || queue > 1); |
| |
| val = rd32(E1000_I210_TQAVCC(queue)); |
| |
| if (mode == QUEUE_MODE_STREAM_RESERVATION) |
| val |= E1000_TQAVCC_QUEUEMODE; |
| else |
| val &= ~E1000_TQAVCC_QUEUEMODE; |
| |
| wr32(E1000_I210_TQAVCC(queue), val); |
| } |
| |
| static bool is_any_cbs_enabled(struct igb_adapter *adapter) |
| { |
| int i; |
| |
| for (i = 0; i < adapter->num_tx_queues; i++) { |
| if (adapter->tx_ring[i]->cbs_enable) |
| return true; |
| } |
| |
| return false; |
| } |
| |
| static bool is_any_txtime_enabled(struct igb_adapter *adapter) |
| { |
| int i; |
| |
| for (i = 0; i < adapter->num_tx_queues; i++) { |
| if (adapter->tx_ring[i]->launchtime_enable) |
| return true; |
| } |
| |
| return false; |
| } |
| |
| /** |
| * igb_config_tx_modes - Configure "Qav Tx mode" features on igb |
| * @adapter: pointer to adapter struct |
| * @queue: queue number |
| * |
| * Configure CBS and Launchtime for a given hardware queue. |
| * Parameters are retrieved from the correct Tx ring, so |
| * igb_save_cbs_params() and igb_save_txtime_params() should be used |
| * for setting those correctly prior to this function being called. |
| **/ |
| static void igb_config_tx_modes(struct igb_adapter *adapter, int queue) |
| { |
| struct net_device *netdev = adapter->netdev; |
| struct e1000_hw *hw = &adapter->hw; |
| struct igb_ring *ring; |
| u32 tqavcc, tqavctrl; |
| u16 value; |
| |
| WARN_ON(hw->mac.type != e1000_i210); |
| WARN_ON(queue < 0 || queue > 1); |
| ring = adapter->tx_ring[queue]; |
| |
| /* If any of the Qav features is enabled, configure queues as SR and |
| * with HIGH PRIO. If none is, then configure them with LOW PRIO and |
| * as SP. |
| */ |
| if (ring->cbs_enable || ring->launchtime_enable) { |
| set_tx_desc_fetch_prio(hw, queue, TX_QUEUE_PRIO_HIGH); |
| set_queue_mode(hw, queue, QUEUE_MODE_STREAM_RESERVATION); |
| } else { |
| set_tx_desc_fetch_prio(hw, queue, TX_QUEUE_PRIO_LOW); |
| set_queue_mode(hw, queue, QUEUE_MODE_STRICT_PRIORITY); |
| } |
| |
| /* If CBS is enabled, set DataTranARB and config its parameters. */ |
| if (ring->cbs_enable || queue == 0) { |
| /* i210 does not allow the queue 0 to be in the Strict |
| * Priority mode while the Qav mode is enabled, so, |
| * instead of disabling strict priority mode, we give |
| * queue 0 the maximum of credits possible. |
| * |
| * See section 8.12.19 of the i210 datasheet, "Note: |
| * Queue0 QueueMode must be set to 1b when |
| * TransmitMode is set to Qav." |
| */ |
| if (queue == 0 && !ring->cbs_enable) { |
| /* max "linkspeed" idleslope in kbps */ |
| ring->idleslope = 1000000; |
| ring->hicredit = ETH_FRAME_LEN; |
| } |
| |
| /* Always set data transfer arbitration to credit-based |
| * shaper algorithm on TQAVCTRL if CBS is enabled for any of |
| * the queues. |
| */ |
| tqavctrl = rd32(E1000_I210_TQAVCTRL); |
| tqavctrl |= E1000_TQAVCTRL_DATATRANARB; |
| wr32(E1000_I210_TQAVCTRL, tqavctrl); |
| |
| /* According to i210 datasheet section 7.2.7.7, we should set |
| * the 'idleSlope' field from TQAVCC register following the |
| * equation: |
| * |
| * For 100 Mbps link speed: |
| * |
| * value = BW * 0x7735 * 0.2 (E1) |
| * |
| * For 1000Mbps link speed: |
| * |
| * value = BW * 0x7735 * 2 (E2) |
| * |
| * E1 and E2 can be merged into one equation as shown below. |
| * Note that 'link-speed' is in Mbps. |
| * |
| * value = BW * 0x7735 * 2 * link-speed |
| * -------------- (E3) |
| * 1000 |
| * |
| * 'BW' is the percentage bandwidth out of full link speed |
| * which can be found with the following equation. Note that |
| * idleSlope here is the parameter from this function which |
| * is in kbps. |
| * |
| * BW = idleSlope |
| * ----------------- (E4) |
| * link-speed * 1000 |
| * |
| * That said, we can come up with a generic equation to |
| * calculate the value we should set it TQAVCC register by |
| * replacing 'BW' in E3 by E4. The resulting equation is: |
| * |
| * value = idleSlope * 0x7735 * 2 * link-speed |
| * ----------------- -------------- (E5) |
| * link-speed * 1000 1000 |
| * |
| * 'link-speed' is present in both sides of the fraction so |
| * it is canceled out. The final equation is the following: |
| * |
| * value = idleSlope * 61034 |
| * ----------------- (E6) |
| * 1000000 |
| * |
| * NOTE: For i210, given the above, we can see that idleslope |
| * is represented in 16.38431 kbps units by the value at |
| * the TQAVCC register (1Gbps / 61034), which reduces |
| * the granularity for idleslope increments. |
| * For instance, if you want to configure a 2576kbps |
| * idleslope, the value to be written on the register |
| * would have to be 157.23. If rounded down, you end |
| * up with less bandwidth available than originally |
| * required (~2572 kbps). If rounded up, you end up |
| * with a higher bandwidth (~2589 kbps). Below the |
| * approach we take is to always round up the |
| * calculated value, so the resulting bandwidth might |
| * be slightly higher for some configurations. |
| */ |
| value = DIV_ROUND_UP_ULL(ring->idleslope * 61034ULL, 1000000); |
| |
| tqavcc = rd32(E1000_I210_TQAVCC(queue)); |
| tqavcc &= ~E1000_TQAVCC_IDLESLOPE_MASK; |
| tqavcc |= value; |
| wr32(E1000_I210_TQAVCC(queue), tqavcc); |
| |
| wr32(E1000_I210_TQAVHC(queue), |
| 0x80000000 + ring->hicredit * 0x7735); |
| } else { |
| |
| /* Set idleSlope to zero. */ |
| tqavcc = rd32(E1000_I210_TQAVCC(queue)); |
| tqavcc &= ~E1000_TQAVCC_IDLESLOPE_MASK; |
| wr32(E1000_I210_TQAVCC(queue), tqavcc); |
| |
| /* Set hiCredit to zero. */ |
| wr32(E1000_I210_TQAVHC(queue), 0); |
| |
| /* If CBS is not enabled for any queues anymore, then return to |
| * the default state of Data Transmission Arbitration on |
| * TQAVCTRL. |
| */ |
| if (!is_any_cbs_enabled(adapter)) { |
| tqavctrl = rd32(E1000_I210_TQAVCTRL); |
| tqavctrl &= ~E1000_TQAVCTRL_DATATRANARB; |
| wr32(E1000_I210_TQAVCTRL, tqavctrl); |
| } |
| } |
| |
| /* If LaunchTime is enabled, set DataTranTIM. */ |
| if (ring->launchtime_enable) { |
| /* Always set DataTranTIM on TQAVCTRL if LaunchTime is enabled |
| * for any of the SR queues, and configure fetchtime delta. |
| * XXX NOTE: |
| * - LaunchTime will be enabled for all SR queues. |
| * - A fixed offset can be added relative to the launch |
| * time of all packets if configured at reg LAUNCH_OS0. |
| * We are keeping it as 0 for now (default value). |
| */ |
| tqavctrl = rd32(E1000_I210_TQAVCTRL); |
| tqavctrl |= E1000_TQAVCTRL_DATATRANTIM | |
| E1000_TQAVCTRL_FETCHTIME_DELTA; |
| wr32(E1000_I210_TQAVCTRL, tqavctrl); |
| } else { |
| /* If Launchtime is not enabled for any SR queues anymore, |
| * then clear DataTranTIM on TQAVCTRL and clear fetchtime delta, |
| * effectively disabling Launchtime. |
| */ |
| if (!is_any_txtime_enabled(adapter)) { |
| tqavctrl = rd32(E1000_I210_TQAVCTRL); |
| tqavctrl &= ~E1000_TQAVCTRL_DATATRANTIM; |
| tqavctrl &= ~E1000_TQAVCTRL_FETCHTIME_DELTA; |
| wr32(E1000_I210_TQAVCTRL, tqavctrl); |
| } |
| } |
| |
| /* XXX: In i210 controller the sendSlope and loCredit parameters from |
| * CBS are not configurable by software so we don't do any 'controller |
| * configuration' in respect to these parameters. |
| */ |
| |
| netdev_dbg(netdev, "Qav Tx mode: cbs %s, launchtime %s, queue %d idleslope %d sendslope %d hiCredit %d locredit %d\n", |
| ring->cbs_enable ? "enabled" : "disabled", |
| ring->launchtime_enable ? "enabled" : "disabled", |
| queue, |
| ring->idleslope, ring->sendslope, |
| ring->hicredit, ring->locredit); |
| } |
| |
| static int igb_save_txtime_params(struct igb_adapter *adapter, int queue, |
| bool enable) |
| { |
| struct igb_ring *ring; |
| |
| if (queue < 0 || queue > adapter->num_tx_queues) |
| return -EINVAL; |
| |
| ring = adapter->tx_ring[queue]; |
| ring->launchtime_enable = enable; |
| |
| return 0; |
| } |
| |
| static int igb_save_cbs_params(struct igb_adapter *adapter, int queue, |
| bool enable, int idleslope, int sendslope, |
| int hicredit, int locredit) |
| { |
| struct igb_ring *ring; |
| |
| if (queue < 0 || queue > adapter->num_tx_queues) |
| return -EINVAL; |
| |
| ring = adapter->tx_ring[queue]; |
| |
| ring->cbs_enable = enable; |
| ring->idleslope = idleslope; |
| ring->sendslope = sendslope; |
| ring->hicredit = hicredit; |
| ring->locredit = locredit; |
| |
| return 0; |
| } |
| |
| /** |
| * igb_setup_tx_mode - Switch to/from Qav Tx mode when applicable |
| * @adapter: pointer to adapter struct |
| * |
| * Configure TQAVCTRL register switching the controller's Tx mode |
| * if FQTSS mode is enabled or disabled. Additionally, will issue |
| * a call to igb_config_tx_modes() per queue so any previously saved |
| * Tx parameters are applied. |
| **/ |
| static void igb_setup_tx_mode(struct igb_adapter *adapter) |
| { |
| struct net_device *netdev = adapter->netdev; |
| struct e1000_hw *hw = &adapter->hw; |
| u32 val; |
| |
| /* Only i210 controller supports changing the transmission mode. */ |
| if (hw->mac.type != e1000_i210) |
| return; |
| |
| if (is_fqtss_enabled(adapter)) { |
| int i, max_queue; |
| |
| /* Configure TQAVCTRL register: set transmit mode to 'Qav', |
| * set data fetch arbitration to 'round robin', set SP_WAIT_SR |
| * so SP queues wait for SR ones. |
| */ |
| val = rd32(E1000_I210_TQAVCTRL); |
| val |= E1000_TQAVCTRL_XMIT_MODE | E1000_TQAVCTRL_SP_WAIT_SR; |
| val &= ~E1000_TQAVCTRL_DATAFETCHARB; |
| wr32(E1000_I210_TQAVCTRL, val); |
| |
| /* Configure Tx and Rx packet buffers sizes as described in |
| * i210 datasheet section 7.2.7.7. |
| */ |
| val = rd32(E1000_TXPBS); |
| val &= ~I210_TXPBSIZE_MASK; |
| val |= I210_TXPBSIZE_PB0_6KB | I210_TXPBSIZE_PB1_6KB | |
| I210_TXPBSIZE_PB2_6KB | I210_TXPBSIZE_PB3_6KB; |
| wr32(E1000_TXPBS, val); |
| |
| val = rd32(E1000_RXPBS); |
| val &= ~I210_RXPBSIZE_MASK; |
| val |= I210_RXPBSIZE_PB_30KB; |
| wr32(E1000_RXPBS, val); |
| |
| /* Section 8.12.9 states that MAX_TPKT_SIZE from DTXMXPKTSZ |
| * register should not exceed the buffer size programmed in |
| * TXPBS. The smallest buffer size programmed in TXPBS is 4kB |
| * so according to the datasheet we should set MAX_TPKT_SIZE to |
| * 4kB / 64. |
| * |
| * However, when we do so, no frame from queue 2 and 3 are |
| * transmitted. It seems the MAX_TPKT_SIZE should not be great |
| * or _equal_ to the buffer size programmed in TXPBS. For this |
| * reason, we set MAX_ TPKT_SIZE to (4kB - 1) / 64. |
| */ |
| val = (4096 - 1) / 64; |
| wr32(E1000_I210_DTXMXPKTSZ, val); |
| |
| /* Since FQTSS mode is enabled, apply any CBS configuration |
| * previously set. If no previous CBS configuration has been |
| * done, then the initial configuration is applied, which means |
| * CBS is disabled. |
| */ |
| max_queue = (adapter->num_tx_queues < I210_SR_QUEUES_NUM) ? |
| adapter->num_tx_queues : I210_SR_QUEUES_NUM; |
| |
| for (i = 0; i < max_queue; i++) { |
| igb_config_tx_modes(adapter, i); |
| } |
| } else { |
| wr32(E1000_RXPBS, I210_RXPBSIZE_DEFAULT); |
| wr32(E1000_TXPBS, I210_TXPBSIZE_DEFAULT); |
| wr32(E1000_I210_DTXMXPKTSZ, I210_DTXMXPKTSZ_DEFAULT); |
| |
| val = rd32(E1000_I210_TQAVCTRL); |
| /* According to Section 8.12.21, the other flags we've set when |
| * enabling FQTSS are not relevant when disabling FQTSS so we |
| * don't set they here. |
| */ |
| val &= ~E1000_TQAVCTRL_XMIT_MODE; |
| wr32(E1000_I210_TQAVCTRL, val); |
| } |
| |
| netdev_dbg(netdev, "FQTSS %s\n", (is_fqtss_enabled(adapter)) ? |
| "enabled" : "disabled"); |
| } |
| |
| /** |
| * igb_configure - configure the hardware for RX and TX |
| * @adapter: private board structure |
| **/ |
| static void igb_configure(struct igb_adapter *adapter) |
| { |
| struct net_device *netdev = adapter->netdev; |
| int i; |
| |
| igb_get_hw_control(adapter); |
| igb_set_rx_mode(netdev); |
| igb_setup_tx_mode(adapter); |
| |
| igb_restore_vlan(adapter); |
| |
| igb_setup_tctl(adapter); |
| igb_setup_mrqc(adapter); |
| igb_setup_rctl(adapter); |
| |
| igb_nfc_filter_restore(adapter); |
| igb_configure_tx(adapter); |
| igb_configure_rx(adapter); |
| |
| igb_rx_fifo_flush_82575(&adapter->hw); |
| |
| /* call igb_desc_unused which always leaves |
| * at least 1 descriptor unused to make sure |
| * next_to_use != next_to_clean |
| */ |
| for (i = 0; i < adapter->num_rx_queues; i++) { |
| struct igb_ring *ring = adapter->rx_ring[i]; |
| igb_alloc_rx_buffers(ring, igb_desc_unused(ring)); |
| } |
| } |
| |
| /** |
| * igb_power_up_link - Power up the phy/serdes link |
| * @adapter: address of board private structure |
| **/ |
| void igb_power_up_link(struct igb_adapter *adapter) |
| { |
| igb_reset_phy(&adapter->hw); |
| |
| if (adapter->hw.phy.media_type == e1000_media_type_copper) |
| igb_power_up_phy_copper(&adapter->hw); |
| else |
| igb_power_up_serdes_link_82575(&adapter->hw); |
| |
| igb_setup_link(&adapter->hw); |
| } |
| |
| /** |
| * igb_power_down_link - Power down the phy/serdes link |
| * @adapter: address of board private structure |
| */ |
| static void igb_power_down_link(struct igb_adapter *adapter) |
| { |
| if (adapter->hw.phy.media_type == e1000_media_type_copper) |
| igb_power_down_phy_copper_82575(&adapter->hw); |
| else |
| igb_shutdown_serdes_link_82575(&adapter->hw); |
| } |
| |
| /** |
| * igb_check_swap_media - Detect and switch function for Media Auto Sense |
| * @adapter: address of the board private structure |
| **/ |
| static void igb_check_swap_media(struct igb_adapter *adapter) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| u32 ctrl_ext, connsw; |
| bool swap_now = false; |
| |
| ctrl_ext = rd32(E1000_CTRL_EXT); |
| connsw = rd32(E1000_CONNSW); |
| |
| /* need to live swap if current media is copper and we have fiber/serdes |
| * to go to. |
| */ |
| |
| if ((hw->phy.media_type == e1000_media_type_copper) && |
| (!(connsw & E1000_CONNSW_AUTOSENSE_EN))) { |
| swap_now = true; |
| } else if ((hw->phy.media_type != e1000_media_type_copper) && |
| !(connsw & E1000_CONNSW_SERDESD)) { |
| /* copper signal takes time to appear */ |
| if (adapter->copper_tries < 4) { |
| adapter->copper_tries++; |
| connsw |= E1000_CONNSW_AUTOSENSE_CONF; |
| wr32(E1000_CONNSW, connsw); |
| return; |
| } else { |
| adapter->copper_tries = 0; |
| if ((connsw & E1000_CONNSW_PHYSD) && |
| (!(connsw & E1000_CONNSW_PHY_PDN))) { |
| swap_now = true; |
| connsw &= ~E1000_CONNSW_AUTOSENSE_CONF; |
| wr32(E1000_CONNSW, connsw); |
| } |
| } |
| } |
| |
| if (!swap_now) |
| return; |
| |
| switch (hw->phy.media_type) { |
| case e1000_media_type_copper: |
| netdev_info(adapter->netdev, |
| "MAS: changing media to fiber/serdes\n"); |
| ctrl_ext |= |
| E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES; |
| adapter->flags |= IGB_FLAG_MEDIA_RESET; |
| adapter->copper_tries = 0; |
| break; |
| case e1000_media_type_internal_serdes: |
| case e1000_media_type_fiber: |
| netdev_info(adapter->netdev, |
| "MAS: changing media to copper\n"); |
| ctrl_ext &= |
| ~E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES; |
| adapter->flags |= IGB_FLAG_MEDIA_RESET; |
| break; |
| default: |
| /* shouldn't get here during regular operation */ |
| netdev_err(adapter->netdev, |
| "AMS: Invalid media type found, returning\n"); |
| break; |
| } |
| wr32(E1000_CTRL_EXT, ctrl_ext); |
| } |
| |
| /** |
| * igb_up - Open the interface and prepare it to handle traffic |
| * @adapter: board private structure |
| **/ |
| int igb_up(struct igb_adapter *adapter) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| int i; |
| |
| /* hardware has been reset, we need to reload some things */ |
| igb_configure(adapter); |
| |
| clear_bit(__IGB_DOWN, &adapter->state); |
| |
| for (i = 0; i < adapter->num_q_vectors; i++) |
| napi_enable(&(adapter->q_vector[i]->napi)); |
| |
| if (adapter->flags & IGB_FLAG_HAS_MSIX) |
| igb_configure_msix(adapter); |
| else |
| igb_assign_vector(adapter->q_vector[0], 0); |
| |
| /* Clear any pending interrupts. */ |
| rd32(E1000_TSICR); |
| rd32(E1000_ICR); |
| igb_irq_enable(adapter); |
| |
| /* notify VFs that reset has been completed */ |
| if (adapter->vfs_allocated_count) { |
| u32 reg_data = rd32(E1000_CTRL_EXT); |
| |
| reg_data |= E1000_CTRL_EXT_PFRSTD; |
| wr32(E1000_CTRL_EXT, reg_data); |
| } |
| |
| netif_tx_start_all_queues(adapter->netdev); |
| |
| /* start the watchdog. */ |
| hw->mac.get_link_status = 1; |
| schedule_work(&adapter->watchdog_task); |
| |
| if ((adapter->flags & IGB_FLAG_EEE) && |
| (!hw->dev_spec._82575.eee_disable)) |
| adapter->eee_advert = MDIO_EEE_100TX | MDIO_EEE_1000T; |
| |
| return 0; |
| } |
| |
| void igb_down(struct igb_adapter *adapter) |
| { |
| struct net_device *netdev = adapter->netdev; |
| struct e1000_hw *hw = &adapter->hw; |
| u32 tctl, rctl; |
| int i; |
| |
| /* signal that we're down so the interrupt handler does not |
| * reschedule our watchdog timer |
| */ |
| set_bit(__IGB_DOWN, &adapter->state); |
| |
| /* disable receives in the hardware */ |
| rctl = rd32(E1000_RCTL); |
| wr32(E1000_RCTL, rctl & ~E1000_RCTL_EN); |
| /* flush and sleep below */ |
| |
| igb_nfc_filter_exit(adapter); |
| |
| netif_carrier_off(netdev); |
| netif_tx_stop_all_queues(netdev); |
| |
| /* disable transmits in the hardware */ |
| tctl = rd32(E1000_TCTL); |
| tctl &= ~E1000_TCTL_EN; |
| wr32(E1000_TCTL, tctl); |
| /* flush both disables and wait for them to finish */ |
| wrfl(); |
| usleep_range(10000, 11000); |
| |
| igb_irq_disable(adapter); |
| |
| adapter->flags &= ~IGB_FLAG_NEED_LINK_UPDATE; |
| |
| for (i = 0; i < adapter->num_q_vectors; i++) { |
| if (adapter->q_vector[i]) { |
| napi_synchronize(&adapter->q_vector[i]->napi); |
| napi_disable(&adapter->q_vector[i]->napi); |
| } |
| } |
| |
| del_timer_sync(&adapter->watchdog_timer); |
| del_timer_sync(&adapter->phy_info_timer); |
| |
| /* record the stats before reset*/ |
| spin_lock(&adapter->stats64_lock); |
| igb_update_stats(adapter); |
| spin_unlock(&adapter->stats64_lock); |
| |
| adapter->link_speed = 0; |
| adapter->link_duplex = 0; |
| |
| if (!pci_channel_offline(adapter->pdev)) |
| igb_reset(adapter); |
| |
| /* clear VLAN promisc flag so VFTA will be updated if necessary */ |
| adapter->flags &= ~IGB_FLAG_VLAN_PROMISC; |
| |
| igb_clean_all_tx_rings(adapter); |
| igb_clean_all_rx_rings(adapter); |
| #ifdef CONFIG_IGB_DCA |
| |
| /* since we reset the hardware DCA settings were cleared */ |
| igb_setup_dca(adapter); |
| #endif |
| } |
| |
| void igb_reinit_locked(struct igb_adapter *adapter) |
| { |
| while (test_and_set_bit(__IGB_RESETTING, &adapter->state)) |
| usleep_range(1000, 2000); |
| igb_down(adapter); |
| igb_up(adapter); |
| clear_bit(__IGB_RESETTING, &adapter->state); |
| } |
| |
| /** igb_enable_mas - Media Autosense re-enable after swap |
| * |
| * @adapter: adapter struct |
| **/ |
| static void igb_enable_mas(struct igb_adapter *adapter) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| u32 connsw = rd32(E1000_CONNSW); |
| |
| /* configure for SerDes media detect */ |
| if ((hw->phy.media_type == e1000_media_type_copper) && |
| (!(connsw & E1000_CONNSW_SERDESD))) { |
| connsw |= E1000_CONNSW_ENRGSRC; |
| connsw |= E1000_CONNSW_AUTOSENSE_EN; |
| wr32(E1000_CONNSW, connsw); |
| wrfl(); |
| } |
| } |
| |
| #ifdef CONFIG_IGB_HWMON |
| /** |
| * igb_set_i2c_bb - Init I2C interface |
| * @hw: pointer to hardware structure |
| **/ |
| static void igb_set_i2c_bb(struct e1000_hw *hw) |
| { |
| u32 ctrl_ext; |
| s32 i2cctl; |
| |
| ctrl_ext = rd32(E1000_CTRL_EXT); |
| ctrl_ext |= E1000_CTRL_I2C_ENA; |
| wr32(E1000_CTRL_EXT, ctrl_ext); |
| wrfl(); |
| |
| i2cctl = rd32(E1000_I2CPARAMS); |
| i2cctl |= E1000_I2CBB_EN |
| | E1000_I2C_CLK_OE_N |
| | E1000_I2C_DATA_OE_N; |
| wr32(E1000_I2CPARAMS, i2cctl); |
| wrfl(); |
| } |
| #endif |
| |
| void igb_reset(struct igb_adapter *adapter) |
| { |
| struct pci_dev *pdev = adapter->pdev; |
| struct e1000_hw *hw = &adapter->hw; |
| struct e1000_mac_info *mac = &hw->mac; |
| struct e1000_fc_info *fc = &hw->fc; |
| u32 pba, hwm; |
| |
| /* Repartition Pba for greater than 9k mtu |
| * To take effect CTRL.RST is required. |
| */ |
| switch (mac->type) { |
| case e1000_i350: |
| case e1000_i354: |
| case e1000_82580: |
| pba = rd32(E1000_RXPBS); |
| pba = igb_rxpbs_adjust_82580(pba); |
| break; |
| case e1000_82576: |
| pba = rd32(E1000_RXPBS); |
| pba &= E1000_RXPBS_SIZE_MASK_82576; |
| break; |
| case e1000_82575: |
| case e1000_i210: |
| case e1000_i211: |
| default: |
| pba = E1000_PBA_34K; |
| break; |
| } |
| |
| if (mac->type == e1000_82575) { |
| u32 min_rx_space, min_tx_space, needed_tx_space; |
| |
| /* write Rx PBA so that hardware can report correct Tx PBA */ |
| wr32(E1000_PBA, pba); |
| |
| /* To maintain wire speed transmits, the Tx FIFO should be |
| * large enough to accommodate two full transmit packets, |
| * rounded up to the next 1KB and expressed in KB. Likewise, |
| * the Rx FIFO should be large enough to accommodate at least |
| * one full receive packet and is similarly rounded up and |
| * expressed in KB. |
| */ |
| min_rx_space = DIV_ROUND_UP(MAX_JUMBO_FRAME_SIZE, 1024); |
| |
| /* The Tx FIFO also stores 16 bytes of information about the Tx |
| * but don't include Ethernet FCS because hardware appends it. |
| * We only need to round down to the nearest 512 byte block |
| * count since the value we care about is 2 frames, not 1. |
| */ |
| min_tx_space = adapter->max_frame_size; |
| min_tx_space += sizeof(union e1000_adv_tx_desc) - ETH_FCS_LEN; |
| min_tx_space = DIV_ROUND_UP(min_tx_space, 512); |
| |
| /* upper 16 bits has Tx packet buffer allocation size in KB */ |
| needed_tx_space = min_tx_space - (rd32(E1000_PBA) >> 16); |
| |
| /* If current Tx allocation is less than the min Tx FIFO size, |
| * and the min Tx FIFO size is less than the current Rx FIFO |
| * allocation, take space away from current Rx allocation. |
| */ |
| if (needed_tx_space < pba) { |
| pba -= needed_tx_space; |
| |
| /* if short on Rx space, Rx wins and must trump Tx |
| * adjustment |
| */ |
| if (pba < min_rx_space) |
| pba = min_rx_space; |
| } |
| |
| /* adjust PBA for jumbo frames */ |
| wr32(E1000_PBA, pba); |
| } |
| |
| /* flow control settings |
| * The high water mark must be low enough to fit one full frame |
| * after transmitting the pause frame. As such we must have enough |
| * space to allow for us to complete our current transmit and then |
| * receive the frame that is in progress from the link partner. |
| * Set it to: |
| * - the full Rx FIFO size minus one full Tx plus one full Rx frame |
| */ |
| hwm = (pba << 10) - (adapter->max_frame_size + MAX_JUMBO_FRAME_SIZE); |
| |
| fc->high_water = hwm & 0xFFFFFFF0; /* 16-byte granularity */ |
| fc->low_water = fc->high_water - 16; |
| fc->pause_time = 0xFFFF; |
| fc->send_xon = 1; |
| fc->current_mode = fc->requested_mode; |
| |
| /* disable receive for all VFs and wait one second */ |
| if (adapter->vfs_allocated_count) { |
| int i; |
| |
| for (i = 0 ; i < adapter->vfs_allocated_count; i++) |
| adapter->vf_data[i].flags &= IGB_VF_FLAG_PF_SET_MAC; |
| |
| /* ping all the active vfs to let them know we are going down */ |
| igb_ping_all_vfs(adapter); |
| |
| /* disable transmits and receives */ |
| wr32(E1000_VFRE, 0); |
| wr32(E1000_VFTE, 0); |
| } |
| |
| /* Allow time for pending master requests to run */ |
| hw->mac.ops.reset_hw(hw); |
| wr32(E1000_WUC, 0); |
| |
| if (adapter->flags & IGB_FLAG_MEDIA_RESET) { |
| /* need to resetup here after media swap */ |
| adapter->ei.get_invariants(hw); |
| adapter->flags &= ~IGB_FLAG_MEDIA_RESET; |
| } |
| if ((mac->type == e1000_82575 || mac->type == e1000_i350) && |
| (adapter->flags & IGB_FLAG_MAS_ENABLE)) { |
| igb_enable_mas(adapter); |
| } |
| if (hw->mac.ops.init_hw(hw)) |
| dev_err(&pdev->dev, "Hardware Error\n"); |
| |
| /* RAR registers were cleared during init_hw, clear mac table */ |
| igb_flush_mac_table(adapter); |
| __dev_uc_unsync(adapter->netdev, NULL); |
| |
| /* Recover default RAR entry */ |
| igb_set_default_mac_filter(adapter); |
| |
| /* Flow control settings reset on hardware reset, so guarantee flow |
| * control is off when forcing speed. |
| */ |
| if (!hw->mac.autoneg) |
| igb_force_mac_fc(hw); |
| |
| igb_init_dmac(adapter, pba); |
| #ifdef CONFIG_IGB_HWMON |
| /* Re-initialize the thermal sensor on i350 devices. */ |
| if (!test_bit(__IGB_DOWN, &adapter->state)) { |
| if (mac->type == e1000_i350 && hw->bus.func == 0) { |
| /* If present, re-initialize the external thermal sensor |
| * interface. |
| */ |
| if (adapter->ets) |
| igb_set_i2c_bb(hw); |
| mac->ops.init_thermal_sensor_thresh(hw); |
| } |
| } |
| #endif |
| /* Re-establish EEE setting */ |
| if (hw->phy.media_type == e1000_media_type_copper) { |
| switch (mac->type) { |
| case e1000_i350: |
| case e1000_i210: |
| case e1000_i211: |
| igb_set_eee_i350(hw, true, true); |
| break; |
| case e1000_i354: |
| igb_set_eee_i354(hw, true, true); |
| break; |
| default: |
| break; |
| } |
| } |
| if (!netif_running(adapter->netdev)) |
| igb_power_down_link(adapter); |
| |
| igb_update_mng_vlan(adapter); |
| |
| /* Enable h/w to recognize an 802.1Q VLAN Ethernet packet */ |
| wr32(E1000_VET, ETHERNET_IEEE_VLAN_TYPE); |
| |
| /* Re-enable PTP, where applicable. */ |
| if (adapter->ptp_flags & IGB_PTP_ENABLED) |
| igb_ptp_reset(adapter); |
| |
| igb_get_phy_info(hw); |
| } |
| |
| static netdev_features_t igb_fix_features(struct net_device *netdev, |
| netdev_features_t features) |
| { |
| /* Since there is no support for separate Rx/Tx vlan accel |
| * enable/disable make sure Tx flag is always in same state as Rx. |
| */ |
| if (features & NETIF_F_HW_VLAN_CTAG_RX) |
| features |= NETIF_F_HW_VLAN_CTAG_TX; |
| else |
| features &= ~NETIF_F_HW_VLAN_CTAG_TX; |
| |
| return features; |
| } |
| |
| static int igb_set_features(struct net_device *netdev, |
| netdev_features_t features) |
| { |
| netdev_features_t changed = netdev->features ^ features; |
| struct igb_adapter *adapter = netdev_priv(netdev); |
| |
| if (changed & NETIF_F_HW_VLAN_CTAG_RX) |
| igb_vlan_mode(netdev, features); |
| |
| if (!(changed & (NETIF_F_RXALL | NETIF_F_NTUPLE))) |
| return 0; |
| |
| if (!(features & NETIF_F_NTUPLE)) { |
| struct hlist_node *node2; |
| struct igb_nfc_filter *rule; |
| |
| spin_lock(&adapter->nfc_lock); |
| hlist_for_each_entry_safe(rule, node2, |
| &adapter->nfc_filter_list, nfc_node) { |
| igb_erase_filter(adapter, rule); |
| hlist_del(&rule->nfc_node); |
| kfree(rule); |
| } |
| spin_unlock(&adapter->nfc_lock); |
| adapter->nfc_filter_count = 0; |
| } |
| |
| netdev->features = features; |
| |
| if (netif_running(netdev)) |
| igb_reinit_locked(adapter); |
| else |
| igb_reset(adapter); |
| |
| return 1; |
| } |
| |
| static int igb_ndo_fdb_add(struct ndmsg *ndm, struct nlattr *tb[], |
| struct net_device *dev, |
| const unsigned char *addr, u16 vid, |
| u16 flags, |
| struct netlink_ext_ack *extack) |
| { |
| /* guarantee we can provide a unique filter for the unicast address */ |
| if (is_unicast_ether_addr(addr) || is_link_local_ether_addr(addr)) { |
| struct igb_adapter *adapter = netdev_priv(dev); |
| int vfn = adapter->vfs_allocated_count; |
| |
| if (netdev_uc_count(dev) >= igb_available_rars(adapter, vfn)) |
| return -ENOMEM; |
| } |
| |
| return ndo_dflt_fdb_add(ndm, tb, dev, addr, vid, flags); |
| } |
| |
| #define IGB_MAX_MAC_HDR_LEN 127 |
| #define IGB_MAX_NETWORK_HDR_LEN 511 |
| |
| static netdev_features_t |
| igb_features_check(struct sk_buff *skb, struct net_device *dev, |
| netdev_features_t features) |
| { |
| unsigned int network_hdr_len, mac_hdr_len; |
| |
| /* Make certain the headers can be described by a context descriptor */ |
| mac_hdr_len = skb_network_offset(skb); |
| if (unlikely(mac_hdr_len > IGB_MAX_MAC_HDR_LEN)) |
| return features & ~(NETIF_F_HW_CSUM | |
| NETIF_F_SCTP_CRC | |
| NETIF_F_GSO_UDP_L4 | |
| NETIF_F_HW_VLAN_CTAG_TX | |
| NETIF_F_TSO | |
| NETIF_F_TSO6); |
| |
| network_hdr_len = skb_checksum_start(skb) - skb_network_header(skb); |
| if (unlikely(network_hdr_len > IGB_MAX_NETWORK_HDR_LEN)) |
| return features & ~(NETIF_F_HW_CSUM | |
| NETIF_F_SCTP_CRC | |
| NETIF_F_GSO_UDP_L4 | |
| NETIF_F_TSO | |
| NETIF_F_TSO6); |
| |
| /* We can only support IPV4 TSO in tunnels if we can mangle the |
| * inner IP ID field, so strip TSO if MANGLEID is not supported. |
| */ |
| if (skb->encapsulation && !(features & NETIF_F_TSO_MANGLEID)) |
| features &= ~NETIF_F_TSO; |
| |
| return features; |
| } |
| |
| static void igb_offload_apply(struct igb_adapter *adapter, s32 queue) |
| { |
| if (!is_fqtss_enabled(adapter)) { |
| enable_fqtss(adapter, true); |
| return; |
| } |
| |
| igb_config_tx_modes(adapter, queue); |
| |
| if (!is_any_cbs_enabled(adapter) && !is_any_txtime_enabled(adapter)) |
| enable_fqtss(adapter, false); |
| } |
| |
| static int igb_offload_cbs(struct igb_adapter *adapter, |
| struct tc_cbs_qopt_offload *qopt) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| int err; |
| |
| /* CBS offloading is only supported by i210 controller. */ |
| if (hw->mac.type != e1000_i210) |
| return -EOPNOTSUPP; |
| |
| /* CBS offloading is only supported by queue 0 and queue 1. */ |
| if (qopt->queue < 0 || qopt->queue > 1) |
| return -EINVAL; |
| |
| err = igb_save_cbs_params(adapter, qopt->queue, qopt->enable, |
| qopt->idleslope, qopt->sendslope, |
| qopt->hicredit, qopt->locredit); |
| if (err) |
| return err; |
| |
| igb_offload_apply(adapter, qopt->queue); |
| |
| return 0; |
| } |
| |
| #define ETHER_TYPE_FULL_MASK ((__force __be16)~0) |
| #define VLAN_PRIO_FULL_MASK (0x07) |
| |
| static int igb_parse_cls_flower(struct igb_adapter *adapter, |
| struct flow_cls_offload *f, |
| int traffic_class, |
| struct igb_nfc_filter *input) |
| { |
| struct flow_rule *rule = flow_cls_offload_flow_rule(f); |
| struct flow_dissector *dissector = rule->match.dissector; |
| struct netlink_ext_ack *extack = f->common.extack; |
| |
| if (dissector->used_keys & |
| ~(BIT_ULL(FLOW_DISSECTOR_KEY_BASIC) | |
| BIT_ULL(FLOW_DISSECTOR_KEY_CONTROL) | |
| BIT_ULL(FLOW_DISSECTOR_KEY_ETH_ADDRS) | |
| BIT_ULL(FLOW_DISSECTOR_KEY_VLAN))) { |
| NL_SET_ERR_MSG_MOD(extack, |
| "Unsupported key used, only BASIC, CONTROL, ETH_ADDRS and VLAN are supported"); |
| return -EOPNOTSUPP; |
| } |
| |
| if (flow_rule_match_has_control_flags(rule, extack)) |
| return -EOPNOTSUPP; |
| |
| if (flow_rule_match_key(rule, FLOW_DISSECTOR_KEY_ETH_ADDRS)) { |
| struct flow_match_eth_addrs match; |
| |
| flow_rule_match_eth_addrs(rule, &match); |
| if (!is_zero_ether_addr(match.mask->dst)) { |
| if (!is_broadcast_ether_addr(match.mask->dst)) { |
| NL_SET_ERR_MSG_MOD(extack, "Only full masks are supported for destination MAC address"); |
| return -EINVAL; |
| } |
| |
| input->filter.match_flags |= |
| IGB_FILTER_FLAG_DST_MAC_ADDR; |
| ether_addr_copy(input->filter.dst_addr, match.key->dst); |
| } |
| |
| if (!is_zero_ether_addr(match.mask->src)) { |
| if (!is_broadcast_ether_addr(match.mask->src)) { |
| NL_SET_ERR_MSG_MOD(extack, "Only full masks are supported for source MAC address"); |
| return -EINVAL; |
| } |
| |
| input->filter.match_flags |= |
| IGB_FILTER_FLAG_SRC_MAC_ADDR; |
| ether_addr_copy(input->filter.src_addr, match.key->src); |
| } |
| } |
| |
| if (flow_rule_match_key(rule, FLOW_DISSECTOR_KEY_BASIC)) { |
| struct flow_match_basic match; |
| |
| flow_rule_match_basic(rule, &match); |
| if (match.mask->n_proto) { |
| if (match.mask->n_proto != ETHER_TYPE_FULL_MASK) { |
| NL_SET_ERR_MSG_MOD(extack, "Only full mask is supported for EtherType filter"); |
| return -EINVAL; |
| } |
| |
| input->filter.match_flags |= IGB_FILTER_FLAG_ETHER_TYPE; |
| input->filter.etype = match.key->n_proto; |
| } |
| } |
| |
| if (flow_rule_match_key(rule, FLOW_DISSECTOR_KEY_VLAN)) { |
| struct flow_match_vlan match; |
| |
| flow_rule_match_vlan(rule, &match); |
| if (match.mask->vlan_priority) { |
| if (match.mask->vlan_priority != VLAN_PRIO_FULL_MASK) { |
| NL_SET_ERR_MSG_MOD(extack, "Only full mask is supported for VLAN priority"); |
| return -EINVAL; |
| } |
| |
| input->filter.match_flags |= IGB_FILTER_FLAG_VLAN_TCI; |
| input->filter.vlan_tci = |
| (__force __be16)match.key->vlan_priority; |
| } |
| } |
| |
| input->action = traffic_class; |
| input->cookie = f->cookie; |
| |
| return 0; |
| } |
| |
| static int igb_configure_clsflower(struct igb_adapter *adapter, |
| struct flow_cls_offload *cls_flower) |
| { |
| struct netlink_ext_ack *extack = cls_flower->common.extack; |
| struct igb_nfc_filter *filter, *f; |
| int err, tc; |
| |
| tc = tc_classid_to_hwtc(adapter->netdev, cls_flower->classid); |
| if (tc < 0) { |
| NL_SET_ERR_MSG_MOD(extack, "Invalid traffic class"); |
| return -EINVAL; |
| } |
| |
| filter = kzalloc(sizeof(*filter), GFP_KERNEL); |
| if (!filter) |
| return -ENOMEM; |
| |
| err = igb_parse_cls_flower(adapter, cls_flower, tc, filter); |
| if (err < 0) |
| goto err_parse; |
| |
| spin_lock(&adapter->nfc_lock); |
| |
| hlist_for_each_entry(f, &adapter->nfc_filter_list, nfc_node) { |
| if (!memcmp(&f->filter, &filter->filter, sizeof(f->filter))) { |
| err = -EEXIST; |
| NL_SET_ERR_MSG_MOD(extack, |
| "This filter is already set in ethtool"); |
| goto err_locked; |
| } |
| } |
| |
| hlist_for_each_entry(f, &adapter->cls_flower_list, nfc_node) { |
| if (!memcmp(&f->filter, &filter->filter, sizeof(f->filter))) { |
| err = -EEXIST; |
| NL_SET_ERR_MSG_MOD(extack, |
| "This filter is already set in cls_flower"); |
| goto err_locked; |
| } |
| } |
| |
| err = igb_add_filter(adapter, filter); |
| if (err < 0) { |
| NL_SET_ERR_MSG_MOD(extack, "Could not add filter to the adapter"); |
| goto err_locked; |
| } |
| |
| hlist_add_head(&filter->nfc_node, &adapter->cls_flower_list); |
| |
| spin_unlock(&adapter->nfc_lock); |
| |
| return 0; |
| |
| err_locked: |
| spin_unlock(&adapter->nfc_lock); |
| |
| err_parse: |
| kfree(filter); |
| |
| return err; |
| } |
| |
| static int igb_delete_clsflower(struct igb_adapter *adapter, |
| struct flow_cls_offload *cls_flower) |
| { |
| struct igb_nfc_filter *filter; |
| int err; |
| |
| spin_lock(&adapter->nfc_lock); |
| |
| hlist_for_each_entry(filter, &adapter->cls_flower_list, nfc_node) |
| if (filter->cookie == cls_flower->cookie) |
| break; |
| |
| if (!filter) { |
| err = -ENOENT; |
| goto out; |
| } |
| |
| err = igb_erase_filter(adapter, filter); |
| if (err < 0) |
| goto out; |
| |
| hlist_del(&filter->nfc_node); |
| kfree(filter); |
| |
| out: |
| spin_unlock(&adapter->nfc_lock); |
| |
| return err; |
| } |
| |
| static int igb_setup_tc_cls_flower(struct igb_adapter *adapter, |
| struct flow_cls_offload *cls_flower) |
| { |
| switch (cls_flower->command) { |
| case FLOW_CLS_REPLACE: |
| return igb_configure_clsflower(adapter, cls_flower); |
| case FLOW_CLS_DESTROY: |
| return igb_delete_clsflower(adapter, cls_flower); |
| case FLOW_CLS_STATS: |
| return -EOPNOTSUPP; |
| default: |
| return -EOPNOTSUPP; |
| } |
| } |
| |
| static int igb_setup_tc_block_cb(enum tc_setup_type type, void *type_data, |
| void *cb_priv) |
| { |
| struct igb_adapter *adapter = cb_priv; |
| |
| if (!tc_cls_can_offload_and_chain0(adapter->netdev, type_data)) |
| return -EOPNOTSUPP; |
| |
| switch (type) { |
| case TC_SETUP_CLSFLOWER: |
| return igb_setup_tc_cls_flower(adapter, type_data); |
| |
| default: |
| return -EOPNOTSUPP; |
| } |
| } |
| |
| static int igb_offload_txtime(struct igb_adapter *adapter, |
| struct tc_etf_qopt_offload *qopt) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| int err; |
| |
| /* Launchtime offloading is only supported by i210 controller. */ |
| if (hw->mac.type != e1000_i210) |
| return -EOPNOTSUPP; |
| |
| /* Launchtime offloading is only supported by queues 0 and 1. */ |
| if (qopt->queue < 0 || qopt->queue > 1) |
| return -EINVAL; |
| |
| err = igb_save_txtime_params(adapter, qopt->queue, qopt->enable); |
| if (err) |
| return err; |
| |
| igb_offload_apply(adapter, qopt->queue); |
| |
| return 0; |
| } |
| |
| static int igb_tc_query_caps(struct igb_adapter *adapter, |
| struct tc_query_caps_base *base) |
| { |
| switch (base->type) { |
| case TC_SETUP_QDISC_TAPRIO: { |
| struct tc_taprio_caps *caps = base->caps; |
| |
| caps->broken_mqprio = true; |
| |
| return 0; |
| } |
| default: |
| return -EOPNOTSUPP; |
| } |
| } |
| |
| static LIST_HEAD(igb_block_cb_list); |
| |
| static int igb_setup_tc(struct net_device *dev, enum tc_setup_type type, |
| void *type_data) |
| { |
| struct igb_adapter *adapter = netdev_priv(dev); |
| |
| switch (type) { |
| case TC_QUERY_CAPS: |
| return igb_tc_query_caps(adapter, type_data); |
| case TC_SETUP_QDISC_CBS: |
| return igb_offload_cbs(adapter, type_data); |
| case TC_SETUP_BLOCK: |
| return flow_block_cb_setup_simple(type_data, |
| &igb_block_cb_list, |
| igb_setup_tc_block_cb, |
| adapter, adapter, true); |
| |
| case TC_SETUP_QDISC_ETF: |
| return igb_offload_txtime(adapter, type_data); |
| |
| default: |
| return -EOPNOTSUPP; |
| } |
| } |
| |
| static int igb_xdp_setup(struct net_device *dev, struct netdev_bpf *bpf) |
| { |
| int i, frame_size = dev->mtu + IGB_ETH_PKT_HDR_PAD; |
| struct igb_adapter *adapter = netdev_priv(dev); |
| struct bpf_prog *prog = bpf->prog, *old_prog; |
| bool running = netif_running(dev); |
| bool need_reset; |
| |
| /* verify igb ring attributes are sufficient for XDP */ |
| for (i = 0; i < adapter->num_rx_queues; i++) { |
| struct igb_ring *ring = adapter->rx_ring[i]; |
| |
| if (frame_size > igb_rx_bufsz(ring)) { |
| NL_SET_ERR_MSG_MOD(bpf->extack, |
| "The RX buffer size is too small for the frame size"); |
| netdev_warn(dev, "XDP RX buffer size %d is too small for the frame size %d\n", |
| igb_rx_bufsz(ring), frame_size); |
| return -EINVAL; |
| } |
| } |
| |
| old_prog = xchg(&adapter->xdp_prog, prog); |
| need_reset = (!!prog != !!old_prog); |
| |
| /* device is up and bpf is added/removed, must setup the RX queues */ |
| if (need_reset && running) { |
| igb_close(dev); |
| } else { |
| for (i = 0; i < adapter->num_rx_queues; i++) |
| (void)xchg(&adapter->rx_ring[i]->xdp_prog, |
| adapter->xdp_prog); |
| } |
| |
| if (old_prog) |
| bpf_prog_put(old_prog); |
| |
| /* bpf is just replaced, RXQ and MTU are already setup */ |
| if (!need_reset) { |
| return 0; |
| } else { |
| if (prog) |
| xdp_features_set_redirect_target(dev, true); |
| else |
| xdp_features_clear_redirect_target(dev); |
| } |
| |
| if (running) |
| igb_open(dev); |
| |
| return 0; |
| } |
| |
| static int igb_xdp(struct net_device *dev, struct netdev_bpf *xdp) |
| { |
| switch (xdp->command) { |
| case XDP_SETUP_PROG: |
| return igb_xdp_setup(dev, xdp); |
| default: |
| return -EINVAL; |
| } |
| } |
| |
| static void igb_xdp_ring_update_tail(struct igb_ring *ring) |
| { |
| /* Force memory writes to complete before letting h/w know there |
| * are new descriptors to fetch. |
| */ |
| wmb(); |
| writel(ring->next_to_use, ring->tail); |
| } |
| |
| static struct igb_ring *igb_xdp_tx_queue_mapping(struct igb_adapter *adapter) |
| { |
| unsigned int r_idx = smp_processor_id(); |
| |
| if (r_idx >= adapter->num_tx_queues) |
| r_idx = r_idx % adapter->num_tx_queues; |
| |
| return adapter->tx_ring[r_idx]; |
| } |
| |
| static int igb_xdp_xmit_back(struct igb_adapter *adapter, struct xdp_buff *xdp) |
| { |
| struct xdp_frame *xdpf = xdp_convert_buff_to_frame(xdp); |
| int cpu = smp_processor_id(); |
| struct igb_ring *tx_ring; |
| struct netdev_queue *nq; |
| u32 ret; |
| |
| if (unlikely(!xdpf)) |
| return IGB_XDP_CONSUMED; |
| |
| /* During program transitions its possible adapter->xdp_prog is assigned |
| * but ring has not been configured yet. In this case simply abort xmit. |
| */ |
| tx_ring = adapter->xdp_prog ? igb_xdp_tx_queue_mapping(adapter) : NULL; |
| if (unlikely(!tx_ring)) |
| return IGB_XDP_CONSUMED; |
| |
| nq = txring_txq(tx_ring); |
| __netif_tx_lock(nq, cpu); |
| /* Avoid transmit queue timeout since we share it with the slow path */ |
| txq_trans_cond_update(nq); |
| ret = igb_xmit_xdp_ring(adapter, tx_ring, xdpf); |
| __netif_tx_unlock(nq); |
| |
| return ret; |
| } |
| |
| static int igb_xdp_xmit(struct net_device *dev, int n, |
| struct xdp_frame **frames, u32 flags) |
| { |
| struct igb_adapter *adapter = netdev_priv(dev); |
| int cpu = smp_processor_id(); |
| struct igb_ring *tx_ring; |
| struct netdev_queue *nq; |
| int nxmit = 0; |
| int i; |
| |
| if (unlikely(test_bit(__IGB_DOWN, &adapter->state))) |
| return -ENETDOWN; |
| |
| if (unlikely(flags & ~XDP_XMIT_FLAGS_MASK)) |
| return -EINVAL; |
| |
| /* During program transitions its possible adapter->xdp_prog is assigned |
| * but ring has not been configured yet. In this case simply abort xmit. |
| */ |
| tx_ring = adapter->xdp_prog ? igb_xdp_tx_queue_mapping(adapter) : NULL; |
| if (unlikely(!tx_ring)) |
| return -ENXIO; |
| |
| nq = txring_txq(tx_ring); |
| __netif_tx_lock(nq, cpu); |
| |
| /* Avoid transmit queue timeout since we share it with the slow path */ |
| txq_trans_cond_update(nq); |
| |
| for (i = 0; i < n; i++) { |
| struct xdp_frame *xdpf = frames[i]; |
| int err; |
| |
| err = igb_xmit_xdp_ring(adapter, tx_ring, xdpf); |
| if (err != IGB_XDP_TX) |
| break; |
| nxmit++; |
| } |
| |
| __netif_tx_unlock(nq); |
| |
| if (unlikely(flags & XDP_XMIT_FLUSH)) |
| igb_xdp_ring_update_tail(tx_ring); |
| |
| return nxmit; |
| } |
| |
| static const struct net_device_ops igb_netdev_ops = { |
| .ndo_open = igb_open, |
| .ndo_stop = igb_close, |
| .ndo_start_xmit = igb_xmit_frame, |
| .ndo_get_stats64 = igb_get_stats64, |
| .ndo_set_rx_mode = igb_set_rx_mode, |
| .ndo_set_mac_address = igb_set_mac, |
| .ndo_change_mtu = igb_change_mtu, |
| .ndo_eth_ioctl = igb_ioctl, |
| .ndo_tx_timeout = igb_tx_timeout, |
| .ndo_validate_addr = eth_validate_addr, |
| .ndo_vlan_rx_add_vid = igb_vlan_rx_add_vid, |
| .ndo_vlan_rx_kill_vid = igb_vlan_rx_kill_vid, |
| .ndo_set_vf_mac = igb_ndo_set_vf_mac, |
| .ndo_set_vf_vlan = igb_ndo_set_vf_vlan, |
| .ndo_set_vf_rate = igb_ndo_set_vf_bw, |
| .ndo_set_vf_spoofchk = igb_ndo_set_vf_spoofchk, |
| .ndo_set_vf_trust = igb_ndo_set_vf_trust, |
| .ndo_get_vf_config = igb_ndo_get_vf_config, |
| .ndo_fix_features = igb_fix_features, |
| .ndo_set_features = igb_set_features, |
| .ndo_fdb_add = igb_ndo_fdb_add, |
| .ndo_features_check = igb_features_check, |
| .ndo_setup_tc = igb_setup_tc, |
| .ndo_bpf = igb_xdp, |
| .ndo_xdp_xmit = igb_xdp_xmit, |
| }; |
| |
| /** |
| * igb_set_fw_version - Configure version string for ethtool |
| * @adapter: adapter struct |
| **/ |
| void igb_set_fw_version(struct igb_adapter *adapter) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| struct e1000_fw_version fw; |
| |
| igb_get_fw_version(hw, &fw); |
| |
| switch (hw->mac.type) { |
| case e1000_i210: |
| case e1000_i211: |
| if (!(igb_get_flash_presence_i210(hw))) { |
| snprintf(adapter->fw_version, |
| sizeof(adapter->fw_version), |
| "%2d.%2d-%d", |
| fw.invm_major, fw.invm_minor, |
| fw.invm_img_type); |
| break; |
| } |
| fallthrough; |
| default: |
| /* if option rom is valid, display its version too */ |
| if (fw.or_valid) { |
| snprintf(adapter->fw_version, |
| sizeof(adapter->fw_version), |
| "%d.%d, 0x%08x, %d.%d.%d", |
| fw.eep_major, fw.eep_minor, fw.etrack_id, |
| fw.or_major, fw.or_build, fw.or_patch); |
| /* no option rom */ |
| } else if (fw.etrack_id != 0X0000) { |
| snprintf(adapter->fw_version, |
| sizeof(adapter->fw_version), |
| "%d.%d, 0x%08x", |
| fw.eep_major, fw.eep_minor, fw.etrack_id); |
| } else { |
| snprintf(adapter->fw_version, |
| sizeof(adapter->fw_version), |
| "%d.%d.%d", |
| fw.eep_major, fw.eep_minor, fw.eep_build); |
| } |
| break; |
| } |
| } |
| |
| /** |
| * igb_init_mas - init Media Autosense feature if enabled in the NVM |
| * |
| * @adapter: adapter struct |
| **/ |
| static void igb_init_mas(struct igb_adapter *adapter) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| u16 eeprom_data; |
| |
| hw->nvm.ops.read(hw, NVM_COMPAT, 1, &eeprom_data); |
| switch (hw->bus.func) { |
| case E1000_FUNC_0: |
| if (eeprom_data & IGB_MAS_ENABLE_0) { |
| adapter->flags |= IGB_FLAG_MAS_ENABLE; |
| netdev_info(adapter->netdev, |
| "MAS: Enabling Media Autosense for port %d\n", |
| hw->bus.func); |
| } |
| break; |
| case E1000_FUNC_1: |
| if (eeprom_data & IGB_MAS_ENABLE_1) { |
| adapter->flags |= IGB_FLAG_MAS_ENABLE; |
| netdev_info(adapter->netdev, |
| "MAS: Enabling Media Autosense for port %d\n", |
| hw->bus.func); |
| } |
| break; |
| case E1000_FUNC_2: |
| if (eeprom_data & IGB_MAS_ENABLE_2) { |
| adapter->flags |= IGB_FLAG_MAS_ENABLE; |
| netdev_info(adapter->netdev, |
| "MAS: Enabling Media Autosense for port %d\n", |
| hw->bus.func); |
| } |
| break; |
| case E1000_FUNC_3: |
| if (eeprom_data & IGB_MAS_ENABLE_3) { |
| adapter->flags |= IGB_FLAG_MAS_ENABLE; |
| netdev_info(adapter->netdev, |
| "MAS: Enabling Media Autosense for port %d\n", |
| hw->bus.func); |
| } |
| break; |
| default: |
| /* Shouldn't get here */ |
| netdev_err(adapter->netdev, |
| "MAS: Invalid port configuration, returning\n"); |
| break; |
| } |
| } |
| |
| /** |
| * igb_init_i2c - Init I2C interface |
| * @adapter: pointer to adapter structure |
| **/ |
| static s32 igb_init_i2c(struct igb_adapter *adapter) |
| { |
| s32 status = 0; |
| |
| /* I2C interface supported on i350 devices */ |
| if (adapter->hw.mac.type != e1000_i350) |
| return 0; |
| |
| /* Initialize the i2c bus which is controlled by the registers. |
| * This bus will use the i2c_algo_bit structure that implements |
| * the protocol through toggling of the 4 bits in the register. |
| */ |
| adapter->i2c_adap.owner = THIS_MODULE; |
| adapter->i2c_algo = igb_i2c_algo; |
| adapter->i2c_algo.data = adapter; |
| adapter->i2c_adap.algo_data = &adapter->i2c_algo; |
| adapter->i2c_adap.dev.parent = &adapter->pdev->dev; |
| strscpy(adapter->i2c_adap.name, "igb BB", |
| sizeof(adapter->i2c_adap.name)); |
| status = i2c_bit_add_bus(&adapter->i2c_adap); |
| return status; |
| } |
| |
| /** |
| * igb_probe - Device Initialization Routine |
| * @pdev: PCI device information struct |
| * @ent: entry in igb_pci_tbl |
| * |
| * Returns 0 on success, negative on failure |
| * |
| * igb_probe initializes an adapter identified by a pci_dev structure. |
| * The OS initialization, configuring of the adapter private structure, |
| * and a hardware reset occur. |
| **/ |
| static int igb_probe(struct pci_dev *pdev, const struct pci_device_id *ent) |
| { |
| struct net_device *netdev; |
| struct igb_adapter *adapter; |
| struct e1000_hw *hw; |
| u16 eeprom_data = 0; |
| s32 ret_val; |
| static int global_quad_port_a; /* global quad port a indication */ |
| const struct e1000_info *ei = igb_info_tbl[ent->driver_data]; |
| u8 part_str[E1000_PBANUM_LENGTH]; |
| int err; |
| |
| /* Catch broken hardware that put the wrong VF device ID in |
| * the PCIe SR-IOV capability. |
| */ |
| if (pdev->is_virtfn) { |
| WARN(1, KERN_ERR "%s (%x:%x) should not be a VF!\n", |
| pci_name(pdev), pdev->vendor, pdev->device); |
| return -EINVAL; |
| } |
| |
| err = pci_enable_device_mem(pdev); |
| if (err) |
| return err; |
| |
| err = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64)); |
| if (err) { |
| dev_err(&pdev->dev, |
| "No usable DMA configuration, aborting\n"); |
| goto err_dma; |
| } |
| |
| err = pci_request_mem_regions(pdev, igb_driver_name); |
| if (err) |
| goto err_pci_reg; |
| |
| pci_set_master(pdev); |
| pci_save_state(pdev); |
| |
| err = -ENOMEM; |
| netdev = alloc_etherdev_mq(sizeof(struct igb_adapter), |
| IGB_MAX_TX_QUEUES); |
| if (!netdev) |
| goto err_alloc_etherdev; |
| |
| SET_NETDEV_DEV(netdev, &pdev->dev); |
| |
| pci_set_drvdata(pdev, netdev); |
| adapter = netdev_priv(netdev); |
| adapter->netdev = netdev; |
| adapter->pdev = pdev; |
| hw = &adapter->hw; |
| hw->back = adapter; |
| adapter->msg_enable = netif_msg_init(debug, DEFAULT_MSG_ENABLE); |
| |
| err = -EIO; |
| adapter->io_addr = pci_iomap(pdev, 0, 0); |
| if (!adapter->io_addr) |
| goto err_ioremap; |
| /* hw->hw_addr can be altered, we'll use adapter->io_addr for unmap */ |
| hw->hw_addr = adapter->io_addr; |
| |
| netdev->netdev_ops = &igb_netdev_ops; |
| igb_set_ethtool_ops(netdev); |
| netdev->watchdog_timeo = 5 * HZ; |
| |
| strscpy(netdev->name, pci_name(pdev), sizeof(netdev->name)); |
| |
| netdev->mem_start = pci_resource_start(pdev, 0); |
| netdev->mem_end = pci_resource_end(pdev, 0); |
| |
| /* PCI config space info */ |
| hw->vendor_id = pdev->vendor; |
| hw->device_id = pdev->device; |
| hw->revision_id = pdev->revision; |
| hw->subsystem_vendor_id = pdev->subsystem_vendor; |
| hw->subsystem_device_id = pdev->subsystem_device; |
| |
| /* Copy the default MAC, PHY and NVM function pointers */ |
| memcpy(&hw->mac.ops, ei->mac_ops, sizeof(hw->mac.ops)); |
| memcpy(&hw->phy.ops, ei->phy_ops, sizeof(hw->phy.ops)); |
| memcpy(&hw->nvm.ops, ei->nvm_ops, sizeof(hw->nvm.ops)); |
| /* Initialize skew-specific constants */ |
| err = ei->get_invariants(hw); |
| if (err) |
| goto err_sw_init; |
| |
| /* setup the private structure */ |
| err = igb_sw_init(adapter); |
| if (err) |
| goto err_sw_init; |
| |
| igb_get_bus_info_pcie(hw); |
| |
| hw->phy.autoneg_wait_to_complete = false; |
| |
| /* Copper options */ |
| if (hw->phy.media_type == e1000_media_type_copper) { |
| hw->phy.mdix = AUTO_ALL_MODES; |
| hw->phy.disable_polarity_correction = false; |
| hw->phy.ms_type = e1000_ms_hw_default; |
| } |
| |
| if (igb_check_reset_block(hw)) |
| dev_info(&pdev->dev, |
| "PHY reset is blocked due to SOL/IDER session.\n"); |
| |
| /* features is initialized to 0 in allocation, it might have bits |
| * set by igb_sw_init so we should use an or instead of an |
| * assignment. |
| */ |
| netdev->features |= NETIF_F_SG | |
| NETIF_F_TSO | |
| NETIF_F_TSO6 | |
| NETIF_F_RXHASH | |
| NETIF_F_RXCSUM | |
| NETIF_F_HW_CSUM; |
| |
| if (hw->mac.type >= e1000_82576) |
| netdev->features |= NETIF_F_SCTP_CRC | NETIF_F_GSO_UDP_L4; |
| |
| if (hw->mac.type >= e1000_i350) |
| netdev->features |= NETIF_F_HW_TC; |
| |
| #define IGB_GSO_PARTIAL_FEATURES (NETIF_F_GSO_GRE | \ |
| NETIF_F_GSO_GRE_CSUM | \ |
| NETIF_F_GSO_IPXIP4 | \ |
| NETIF_F_GSO_IPXIP6 | \ |
| NETIF_F_GSO_UDP_TUNNEL | \ |
| NETIF_F_GSO_UDP_TUNNEL_CSUM) |
| |
| netdev->gso_partial_features = IGB_GSO_PARTIAL_FEATURES; |
| netdev->features |= NETIF_F_GSO_PARTIAL | IGB_GSO_PARTIAL_FEATURES; |
| |
| /* copy netdev features into list of user selectable features */ |
| netdev->hw_features |= netdev->features | |
| NETIF_F_HW_VLAN_CTAG_RX | |
| NETIF_F_HW_VLAN_CTAG_TX | |
| NETIF_F_RXALL; |
| |
| if (hw->mac.type >= e1000_i350) |
| netdev->hw_features |= NETIF_F_NTUPLE; |
| |
| netdev->features |= NETIF_F_HIGHDMA; |
| |
| netdev->vlan_features |= netdev->features | NETIF_F_TSO_MANGLEID; |
| netdev->mpls_features |= NETIF_F_HW_CSUM; |
| netdev->hw_enc_features |= netdev->vlan_features; |
| |
| /* set this bit last since it cannot be part of vlan_features */ |
| netdev->features |= NETIF_F_HW_VLAN_CTAG_FILTER | |
| NETIF_F_HW_VLAN_CTAG_RX | |
| NETIF_F_HW_VLAN_CTAG_TX; |
| |
| netdev->priv_flags |= IFF_SUPP_NOFCS; |
| |
| netdev->priv_flags |= IFF_UNICAST_FLT; |
| netdev->xdp_features = NETDEV_XDP_ACT_BASIC | NETDEV_XDP_ACT_REDIRECT; |
| |
| /* MTU range: 68 - 9216 */ |
| netdev->min_mtu = ETH_MIN_MTU; |
| netdev->max_mtu = MAX_STD_JUMBO_FRAME_SIZE; |
| |
| adapter->en_mng_pt = igb_enable_mng_pass_thru(hw); |
| |
| /* before reading the NVM, reset the controller to put the device in a |
| * known good starting state |
| */ |
| hw->mac.ops.reset_hw(hw); |
| |
| /* make sure the NVM is good , i211/i210 parts can have special NVM |
| * that doesn't contain a checksum |
| */ |
| switch (hw->mac.type) { |
| case e1000_i210: |
| case e1000_i211: |
| if (igb_get_flash_presence_i210(hw)) { |
| if (hw->nvm.ops.validate(hw) < 0) { |
| dev_err(&pdev->dev, |
| "The NVM Checksum Is Not Valid\n"); |
| err = -EIO; |
| goto err_eeprom; |
| } |
| } |
| break; |
| default: |
| if (hw->nvm.ops.validate(hw) < 0) { |
| dev_err(&pdev->dev, "The NVM Checksum Is Not Valid\n"); |
| err = -EIO; |
| goto err_eeprom; |
| } |
| break; |
| } |
| |
| if (eth_platform_get_mac_address(&pdev->dev, hw->mac.addr)) { |
| /* copy the MAC address out of the NVM */ |
| if (hw->mac.ops.read_mac_addr(hw)) |
| dev_err(&pdev->dev, "NVM Read Error\n"); |
| } |
| |
| eth_hw_addr_set(netdev, hw->mac.addr); |
| |
| if (!is_valid_ether_addr(netdev->dev_addr)) { |
| dev_err(&pdev->dev, "Invalid MAC Address\n"); |
| err = -EIO; |
| goto err_eeprom; |
| } |
| |
| igb_set_default_mac_filter(adapter); |
| |
| /* get firmware version for ethtool -i */ |
| igb_set_fw_version(adapter); |
| |
| /* configure RXPBSIZE and TXPBSIZE */ |
| if (hw->mac.type == e1000_i210) { |
| wr32(E1000_RXPBS, I210_RXPBSIZE_DEFAULT); |
| wr32(E1000_TXPBS, I210_TXPBSIZE_DEFAULT); |
| } |
| |
| timer_setup(&adapter->watchdog_timer, igb_watchdog, 0); |
| timer_setup(&adapter->phy_info_timer, igb_update_phy_info, 0); |
| |
| INIT_WORK(&adapter->reset_task, igb_reset_task); |
| INIT_WORK(&adapter->watchdog_task, igb_watchdog_task); |
| |
| /* Initialize link properties that are user-changeable */ |
| adapter->fc_autoneg = true; |
| hw->mac.autoneg = true; |
| hw->phy.autoneg_advertised = 0x2f; |
| |
| hw->fc.requested_mode = e1000_fc_default; |
| hw->fc.current_mode = e1000_fc_default; |
| |
| igb_validate_mdi_setting(hw); |
| |
| /* By default, support wake on port A */ |
| if (hw->bus.func == 0) |
| adapter->flags |= IGB_FLAG_WOL_SUPPORTED; |
| |
| /* Check the NVM for wake support on non-port A ports */ |
| if (hw->mac.type >= e1000_82580) |
| hw->nvm.ops.read(hw, NVM_INIT_CONTROL3_PORT_A + |
| NVM_82580_LAN_FUNC_OFFSET(hw->bus.func), 1, |
| &eeprom_data); |
| else if (hw->bus.func == 1) |
| hw->nvm.ops.read(hw, NVM_INIT_CONTROL3_PORT_B, 1, &eeprom_data); |
| |
| if (eeprom_data & IGB_EEPROM_APME) |
| adapter->flags |= IGB_FLAG_WOL_SUPPORTED; |
| |
| /* now that we have the eeprom settings, apply the special cases where |
| * the eeprom may be wrong or the board simply won't support wake on |
| * lan on a particular port |
| */ |
| switch (pdev->device) { |
| case E1000_DEV_ID_82575GB_QUAD_COPPER: |
| adapter->flags &= ~IGB_FLAG_WOL_SUPPORTED; |
| break; |
| case E1000_DEV_ID_82575EB_FIBER_SERDES: |
| case E1000_DEV_ID_82576_FIBER: |
| case E1000_DEV_ID_82576_SERDES: |
| /* Wake events only supported on port A for dual fiber |
| * regardless of eeprom setting |
| */ |
| if (rd32(E1000_STATUS) & E1000_STATUS_FUNC_1) |
| adapter->flags &= ~IGB_FLAG_WOL_SUPPORTED; |
| break; |
| case E1000_DEV_ID_82576_QUAD_COPPER: |
| case E1000_DEV_ID_82576_QUAD_COPPER_ET2: |
| /* if quad port adapter, disable WoL on all but port A */ |
| if (global_quad_port_a != 0) |
| adapter->flags &= ~IGB_FLAG_WOL_SUPPORTED; |
| else |
| adapter->flags |= IGB_FLAG_QUAD_PORT_A; |
| /* Reset for multiple quad port adapters */ |
| if (++global_quad_port_a == 4) |
| global_quad_port_a = 0; |
| break; |
| default: |
| /* If the device can't wake, don't set software support */ |
| if (!device_can_wakeup(&adapter->pdev->dev)) |
| adapter->flags &= ~IGB_FLAG_WOL_SUPPORTED; |
| } |
| |
| /* initialize the wol settings based on the eeprom settings */ |
| if (adapter->flags & IGB_FLAG_WOL_SUPPORTED) |
| adapter->wol |= E1000_WUFC_MAG; |
| |
| /* Some vendors want WoL disabled by default, but still supported */ |
| if ((hw->mac.type == e1000_i350) && |
| (pdev->subsystem_vendor == PCI_VENDOR_ID_HP)) { |
| adapter->flags |= IGB_FLAG_WOL_SUPPORTED; |
| adapter->wol = 0; |
| } |
| |
| /* Some vendors want the ability to Use the EEPROM setting as |
| * enable/disable only, and not for capability |
| */ |
| if (((hw->mac.type == e1000_i350) || |
| (hw->mac.type == e1000_i354)) && |
| (pdev->subsystem_vendor == PCI_VENDOR_ID_DELL)) { |
| adapter->flags |= IGB_FLAG_WOL_SUPPORTED; |
| adapter->wol = 0; |
| } |
| if (hw->mac.type == e1000_i350) { |
| if (((pdev->subsystem_device == 0x5001) || |
| (pdev->subsystem_device == 0x5002)) && |
| (hw->bus.func == 0)) { |
| adapter->flags |= IGB_FLAG_WOL_SUPPORTED; |
| adapter->wol = 0; |
| } |
| if (pdev->subsystem_device == 0x1F52) |
| adapter->flags |= IGB_FLAG_WOL_SUPPORTED; |
| } |
| |
| device_set_wakeup_enable(&adapter->pdev->dev, |
| adapter->flags & IGB_FLAG_WOL_SUPPORTED); |
| |
| /* reset the hardware with the new settings */ |
| igb_reset(adapter); |
| |
| /* Init the I2C interface */ |
| err = igb_init_i2c(adapter); |
| if (err) { |
| dev_err(&pdev->dev, "failed to init i2c interface\n"); |
| goto err_eeprom; |
| } |
| |
| /* let the f/w know that the h/w is now under the control of the |
| * driver. |
| */ |
| igb_get_hw_control(adapter); |
| |
| strcpy(netdev->name, "eth%d"); |
| err = register_netdev(netdev); |
| if (err) |
| goto err_register; |
| |
| /* carrier off reporting is important to ethtool even BEFORE open */ |
| netif_carrier_off(netdev); |
| |
| #ifdef CONFIG_IGB_DCA |
| if (dca_add_requester(&pdev->dev) == 0) { |
| adapter->flags |= IGB_FLAG_DCA_ENABLED; |
| dev_info(&pdev->dev, "DCA enabled\n"); |
| igb_setup_dca(adapter); |
| } |
| |
| #endif |
| #ifdef CONFIG_IGB_HWMON |
| /* Initialize the thermal sensor on i350 devices. */ |
| if (hw->mac.type == e1000_i350 && hw->bus.func == 0) { |
| u16 ets_word; |
| |
| /* Read the NVM to determine if this i350 device supports an |
| * external thermal sensor. |
| */ |
| hw->nvm.ops.read(hw, NVM_ETS_CFG, 1, &ets_word); |
| if (ets_word != 0x0000 && ets_word != 0xFFFF) |
| adapter->ets = true; |
| else |
| adapter->ets = false; |
| /* Only enable I2C bit banging if an external thermal |
| * sensor is supported. |
| */ |
| if (adapter->ets) |
| igb_set_i2c_bb(hw); |
| hw->mac.ops.init_thermal_sensor_thresh(hw); |
| if (igb_sysfs_init(adapter)) |
| dev_err(&pdev->dev, |
| "failed to allocate sysfs resources\n"); |
| } else { |
| adapter->ets = false; |
| } |
| #endif |
| /* Check if Media Autosense is enabled */ |
| adapter->ei = *ei; |
| if (hw->dev_spec._82575.mas_capable) |
| igb_init_mas(adapter); |
| |
| /* do hw tstamp init after resetting */ |
| igb_ptp_init(adapter); |
| |
| dev_info(&pdev->dev, "Intel(R) Gigabit Ethernet Network Connection\n"); |
| /* print bus type/speed/width info, not applicable to i354 */ |
| if (hw->mac.type != e1000_i354) { |
| dev_info(&pdev->dev, "%s: (PCIe:%s:%s) %pM\n", |
| netdev->name, |
| ((hw->bus.speed == e1000_bus_speed_2500) ? "2.5Gb/s" : |
| (hw->bus.speed == e1000_bus_speed_5000) ? "5.0Gb/s" : |
| "unknown"), |
| ((hw->bus.width == e1000_bus_width_pcie_x4) ? |
| "Width x4" : |
| (hw->bus.width == e1000_bus_width_pcie_x2) ? |
| "Width x2" : |
| (hw->bus.width == e1000_bus_width_pcie_x1) ? |
| "Width x1" : "unknown"), netdev->dev_addr); |
| } |
| |
| if ((hw->mac.type == e1000_82576 && |
| rd32(E1000_EECD) & E1000_EECD_PRES) || |
| (hw->mac.type >= e1000_i210 || |
| igb_get_flash_presence_i210(hw))) { |
| ret_val = igb_read_part_string(hw, part_str, |
| E1000_PBANUM_LENGTH); |
| } else { |
| ret_val = -E1000_ERR_INVM_VALUE_NOT_FOUND; |
| } |
| |
| if (ret_val) |
| strcpy(part_str, "Unknown"); |
| dev_info(&pdev->dev, "%s: PBA No: %s\n", netdev->name, part_str); |
| dev_info(&pdev->dev, |
| "Using %s interrupts. %d rx queue(s), %d tx queue(s)\n", |
| (adapter->flags & IGB_FLAG_HAS_MSIX) ? "MSI-X" : |
| (adapter->flags & IGB_FLAG_HAS_MSI) ? "MSI" : "legacy", |
| adapter->num_rx_queues, adapter->num_tx_queues); |
| if (hw->phy.media_type == e1000_media_type_copper) { |
| switch (hw->mac.type) { |
| case e1000_i350: |
| case e1000_i210: |
| case e1000_i211: |
| /* Enable EEE for internal copper PHY devices */ |
| err = igb_set_eee_i350(hw, true, true); |
| if ((!err) && |
| (!hw->dev_spec._82575.eee_disable)) { |
| adapter->eee_advert = |
| MDIO_EEE_100TX | MDIO_EEE_1000T; |
| adapter->flags |= IGB_FLAG_EEE; |
| } |
| break; |
| case e1000_i354: |
| if ((rd32(E1000_CTRL_EXT) & |
| E1000_CTRL_EXT_LINK_MODE_SGMII)) { |
| err = igb_set_eee_i354(hw, true, true); |
| if ((!err) && |
| (!hw->dev_spec._82575.eee_disable)) { |
| adapter->eee_advert = |
| MDIO_EEE_100TX | MDIO_EEE_1000T; |
| adapter->flags |= IGB_FLAG_EEE; |
| } |
| } |
| break; |
| default: |
| break; |
| } |
| } |
| |
| dev_pm_set_driver_flags(&pdev->dev, DPM_FLAG_NO_DIRECT_COMPLETE); |
| |
| pm_runtime_put_noidle(&pdev->dev); |
| return 0; |
| |
| err_register: |
| igb_release_hw_control(adapter); |
| memset(&adapter->i2c_adap, 0, sizeof(adapter->i2c_adap)); |
| err_eeprom: |
| if (!igb_check_reset_block(hw)) |
| igb_reset_phy(hw); |
| |
| if (hw->flash_address) |
| iounmap(hw->flash_address); |
| err_sw_init: |
| kfree(adapter->mac_table); |
| kfree(adapter->shadow_vfta); |
| igb_clear_interrupt_scheme(adapter); |
| #ifdef CONFIG_PCI_IOV |
| igb_disable_sriov(pdev, false); |
| #endif |
| pci_iounmap(pdev, adapter->io_addr); |
| err_ioremap: |
| free_netdev(netdev); |
| err_alloc_etherdev: |
| pci_release_mem_regions(pdev); |
| err_pci_reg: |
| err_dma: |
| pci_disable_device(pdev); |
| return err; |
| } |
| |
| #ifdef CONFIG_PCI_IOV |
| static int igb_sriov_reinit(struct pci_dev *dev) |
| { |
| struct net_device *netdev = pci_get_drvdata(dev); |
| struct igb_adapter *adapter = netdev_priv(netdev); |
| struct pci_dev *pdev = adapter->pdev; |
| |
| rtnl_lock(); |
| |
| if (netif_running(netdev)) |
| igb_close(netdev); |
| else |
| igb_reset(adapter); |
| |
| igb_clear_interrupt_scheme(adapter); |
| |
| igb_init_queue_configuration(adapter); |
| |
| if (igb_init_interrupt_scheme(adapter, true)) { |
| rtnl_unlock(); |
| dev_err(&pdev->dev, "Unable to allocate memory for queues\n"); |
| return -ENOMEM; |
| } |
| |
| if (netif_running(netdev)) |
| igb_open(netdev); |
| |
| rtnl_unlock(); |
| |
| return 0; |
| } |
| |
| static int igb_disable_sriov(struct pci_dev *pdev, bool reinit) |
| { |
| struct net_device *netdev = pci_get_drvdata(pdev); |
| struct igb_adapter *adapter = netdev_priv(netdev); |
| struct e1000_hw *hw = &adapter->hw; |
| unsigned long flags; |
| |
| /* reclaim resources allocated to VFs */ |
| if (adapter->vf_data) { |
| /* disable iov and allow time for transactions to clear */ |
| if (pci_vfs_assigned(pdev)) { |
| dev_warn(&pdev->dev, |
| "Cannot deallocate SR-IOV virtual functions while they are assigned - VFs will not be deallocated\n"); |
| return -EPERM; |
| } else { |
| pci_disable_sriov(pdev); |
| msleep(500); |
| } |
| spin_lock_irqsave(&adapter->vfs_lock, flags); |
| kfree(adapter->vf_mac_list); |
| adapter->vf_mac_list = NULL; |
| kfree(adapter->vf_data); |
| adapter->vf_data = NULL; |
| adapter->vfs_allocated_count = 0; |
| spin_unlock_irqrestore(&adapter->vfs_lock, flags); |
| wr32(E1000_IOVCTL, E1000_IOVCTL_REUSE_VFQ); |
| wrfl(); |
| msleep(100); |
| dev_info(&pdev->dev, "IOV Disabled\n"); |
| |
| /* Re-enable DMA Coalescing flag since IOV is turned off */ |
| adapter->flags |= IGB_FLAG_DMAC; |
| } |
| |
| return reinit ? igb_sriov_reinit(pdev) : 0; |
| } |
| |
| static int igb_enable_sriov(struct pci_dev *pdev, int num_vfs, bool reinit) |
| { |
| struct net_device *netdev = pci_get_drvdata(pdev); |
| struct igb_adapter *adapter = netdev_priv(netdev); |
| int old_vfs = pci_num_vf(pdev); |
| struct vf_mac_filter *mac_list; |
| int err = 0; |
| int num_vf_mac_filters, i; |
| |
| if (!(adapter->flags & IGB_FLAG_HAS_MSIX) || num_vfs > 7) { |
| err = -EPERM; |
| goto out; |
| } |
| if (!num_vfs) |
| goto out; |
| |
| if (old_vfs) { |
| dev_info(&pdev->dev, "%d pre-allocated VFs found - override max_vfs setting of %d\n", |
| old_vfs, max_vfs); |
| adapter->vfs_allocated_count = old_vfs; |
| } else |
| adapter->vfs_allocated_count = num_vfs; |
| |
| adapter->vf_data = kcalloc(adapter->vfs_allocated_count, |
| sizeof(struct vf_data_storage), GFP_KERNEL); |
| |
| /* if allocation failed then we do not support SR-IOV */ |
| if (!adapter->vf_data) { |
| adapter->vfs_allocated_count = 0; |
| err = -ENOMEM; |
| goto out; |
| } |
| |
| /* Due to the limited number of RAR entries calculate potential |
| * number of MAC filters available for the VFs. Reserve entries |
| * for PF default MAC, PF MAC filters and at least one RAR entry |
| * for each VF for VF MAC. |
| */ |
| num_vf_mac_filters = adapter->hw.mac.rar_entry_count - |
| (1 + IGB_PF_MAC_FILTERS_RESERVED + |
| adapter->vfs_allocated_count); |
| |
| adapter->vf_mac_list = kcalloc(num_vf_mac_filters, |
| sizeof(struct vf_mac_filter), |
| GFP_KERNEL); |
| |
| mac_list = adapter->vf_mac_list; |
| INIT_LIST_HEAD(&adapter->vf_macs.l); |
| |
| if (adapter->vf_mac_list) { |
| /* Initialize list of VF MAC filters */ |
| for (i = 0; i < num_vf_mac_filters; i++) { |
| mac_list->vf = -1; |
| mac_list->free = true; |
| list_add(&mac_list->l, &adapter->vf_macs.l); |
| mac_list++; |
| } |
| } else { |
| /* If we could not allocate memory for the VF MAC filters |
| * we can continue without this feature but warn user. |
| */ |
| dev_err(&pdev->dev, |
| "Unable to allocate memory for VF MAC filter list\n"); |
| } |
| |
| dev_info(&pdev->dev, "%d VFs allocated\n", |
| adapter->vfs_allocated_count); |
| for (i = 0; i < adapter->vfs_allocated_count; i++) |
| igb_vf_configure(adapter, i); |
| |
| /* DMA Coalescing is not supported in IOV mode. */ |
| adapter->flags &= ~IGB_FLAG_DMAC; |
| |
| if (reinit) { |
| err = igb_sriov_reinit(pdev); |
| if (err) |
| goto err_out; |
| } |
| |
| /* only call pci_enable_sriov() if no VFs are allocated already */ |
| if (!old_vfs) { |
| err = pci_enable_sriov(pdev, adapter->vfs_allocated_count); |
| if (err) |
| goto err_out; |
| } |
| |
| goto out; |
| |
| err_out: |
| kfree(adapter->vf_mac_list); |
| adapter->vf_mac_list = NULL; |
| kfree(adapter->vf_data); |
| adapter->vf_data = NULL; |
| adapter->vfs_allocated_count = 0; |
| out: |
| return err; |
| } |
| |
| #endif |
| /** |
| * igb_remove_i2c - Cleanup I2C interface |
| * @adapter: pointer to adapter structure |
| **/ |
| static void igb_remove_i2c(struct igb_adapter *adapter) |
| { |
| /* free the adapter bus structure */ |
| i2c_del_adapter(&adapter->i2c_adap); |
| } |
| |
| /** |
| * igb_remove - Device Removal Routine |
| * @pdev: PCI device information struct |
| * |
| * igb_remove is called by the PCI subsystem to alert the driver |
| * that it should release a PCI device. The could be caused by a |
| * Hot-Plug event, or because the driver is going to be removed from |
| * memory. |
| **/ |
| static void igb_remove(struct pci_dev *pdev) |
| { |
| struct net_device *netdev = pci_get_drvdata(pdev); |
| struct igb_adapter *adapter = netdev_priv(netdev); |
| struct e1000_hw *hw = &adapter->hw; |
| |
| pm_runtime_get_noresume(&pdev->dev); |
| #ifdef CONFIG_IGB_HWMON |
| igb_sysfs_exit(adapter); |
| #endif |
| igb_remove_i2c(adapter); |
| igb_ptp_stop(adapter); |
| /* The watchdog timer may be rescheduled, so explicitly |
| * disable watchdog from being rescheduled. |
| */ |
| set_bit(__IGB_DOWN, &adapter->state); |
| del_timer_sync(&adapter->watchdog_timer); |
| del_timer_sync(&adapter->phy_info_timer); |
| |
| cancel_work_sync(&adapter->reset_task); |
| cancel_work_sync(&adapter->watchdog_task); |
| |
| #ifdef CONFIG_IGB_DCA |
| if (adapter->flags & IGB_FLAG_DCA_ENABLED) { |
| dev_info(&pdev->dev, "DCA disabled\n"); |
| dca_remove_requester(&pdev->dev); |
| adapter->flags &= ~IGB_FLAG_DCA_ENABLED; |
| wr32(E1000_DCA_CTRL, E1000_DCA_CTRL_DCA_MODE_DISABLE); |
| } |
| #endif |
| |
| /* Release control of h/w to f/w. If f/w is AMT enabled, this |
| * would have already happened in close and is redundant. |
| */ |
| igb_release_hw_control(adapter); |
| |
| #ifdef CONFIG_PCI_IOV |
| igb_disable_sriov(pdev, false); |
| #endif |
| |
| unregister_netdev(netdev); |
| |
| igb_clear_interrupt_scheme(adapter); |
| |
| pci_iounmap(pdev, adapter->io_addr); |
| if (hw->flash_address) |
| iounmap(hw->flash_address); |
| pci_release_mem_regions(pdev); |
| |
| kfree(adapter->mac_table); |
| kfree(adapter->shadow_vfta); |
| free_netdev(netdev); |
| |
| pci_disable_device(pdev); |
| } |
| |
| /** |
| * igb_probe_vfs - Initialize vf data storage and add VFs to pci config space |
| * @adapter: board private structure to initialize |
| * |
| * This function initializes the vf specific data storage and then attempts to |
| * allocate the VFs. The reason for ordering it this way is because it is much |
| * mor expensive time wise to disable SR-IOV than it is to allocate and free |
| * the memory for the VFs. |
| **/ |
| static void igb_probe_vfs(struct igb_adapter *adapter) |
| { |
| #ifdef CONFIG_PCI_IOV |
| struct pci_dev *pdev = adapter->pdev; |
| struct e1000_hw *hw = &adapter->hw; |
| |
| /* Virtualization features not supported on i210 and 82580 family. */ |
| if ((hw->mac.type == e1000_i210) || (hw->mac.type == e1000_i211) || |
| (hw->mac.type == e1000_82580)) |
| return; |
| |
| /* Of the below we really only want the effect of getting |
| * IGB_FLAG_HAS_MSIX set (if available), without which |
| * igb_enable_sriov() has no effect. |
| */ |
| igb_set_interrupt_capability(adapter, true); |
| igb_reset_interrupt_capability(adapter); |
| |
| pci_sriov_set_totalvfs(pdev, 7); |
| igb_enable_sriov(pdev, max_vfs, false); |
| |
| #endif /* CONFIG_PCI_IOV */ |
| } |
| |
| unsigned int igb_get_max_rss_queues(struct igb_adapter *adapter) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| unsigned int max_rss_queues; |
| |
| /* Determine the maximum number of RSS queues supported. */ |
| switch (hw->mac.type) { |
| case e1000_i211: |
| max_rss_queues = IGB_MAX_RX_QUEUES_I211; |
| break; |
| case e1000_82575: |
| case e1000_i210: |
| max_rss_queues = IGB_MAX_RX_QUEUES_82575; |
| break; |
| case e1000_i350: |
| /* I350 cannot do RSS and SR-IOV at the same time */ |
| if (!!adapter->vfs_allocated_count) { |
| max_rss_queues = 1; |
| break; |
| } |
| fallthrough; |
| case e1000_82576: |
| if (!!adapter->vfs_allocated_count) { |
| max_rss_queues = 2; |
| break; |
| } |
| fallthrough; |
| case e1000_82580: |
| case e1000_i354: |
| default: |
| max_rss_queues = IGB_MAX_RX_QUEUES; |
| break; |
| } |
| |
| return max_rss_queues; |
| } |
| |
| static void igb_init_queue_configuration(struct igb_adapter *adapter) |
| { |
| u32 max_rss_queues; |
| |
| max_rss_queues = igb_get_max_rss_queues(adapter); |
| adapter->rss_queues = min_t(u32, max_rss_queues, num_online_cpus()); |
| |
| igb_set_flag_queue_pairs(adapter, max_rss_queues); |
| } |
| |
| void igb_set_flag_queue_pairs(struct igb_adapter *adapter, |
| const u32 max_rss_queues) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| |
| /* Determine if we need to pair queues. */ |
| switch (hw->mac.type) { |
| case e1000_82575: |
| case e1000_i211: |
| /* Device supports enough interrupts without queue pairing. */ |
| break; |
| case e1000_82576: |
| case e1000_82580: |
| case e1000_i350: |
| case e1000_i354: |
| case e1000_i210: |
| default: |
| /* If rss_queues > half of max_rss_queues, pair the queues in |
| * order to conserve interrupts due to limited supply. |
| */ |
| if (adapter->rss_queues > (max_rss_queues / 2)) |
| adapter->flags |= IGB_FLAG_QUEUE_PAIRS; |
| else |
| adapter->flags &= ~IGB_FLAG_QUEUE_PAIRS; |
| break; |
| } |
| } |
| |
| /** |
| * igb_sw_init - Initialize general software structures (struct igb_adapter) |
| * @adapter: board private structure to initialize |
| * |
| * igb_sw_init initializes the Adapter private data structure. |
| * Fields are initialized based on PCI device information and |
| * OS network device settings (MTU size). |
| **/ |
| static int igb_sw_init(struct igb_adapter *adapter) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| struct net_device *netdev = adapter->netdev; |
| struct pci_dev *pdev = adapter->pdev; |
| |
| pci_read_config_word(pdev, PCI_COMMAND, &hw->bus.pci_cmd_word); |
| |
| /* set default ring sizes */ |
| adapter->tx_ring_count = IGB_DEFAULT_TXD; |
| adapter->rx_ring_count = IGB_DEFAULT_RXD; |
| |
| /* set default ITR values */ |
| adapter->rx_itr_setting = IGB_DEFAULT_ITR; |
| adapter->tx_itr_setting = IGB_DEFAULT_ITR; |
| |
| /* set default work limits */ |
| adapter->tx_work_limit = IGB_DEFAULT_TX_WORK; |
| |
| adapter->max_frame_size = netdev->mtu + IGB_ETH_PKT_HDR_PAD; |
| adapter->min_frame_size = ETH_ZLEN + ETH_FCS_LEN; |
| |
| spin_lock_init(&adapter->nfc_lock); |
| spin_lock_init(&adapter->stats64_lock); |
| |
| /* init spinlock to avoid concurrency of VF resources */ |
| spin_lock_init(&adapter->vfs_lock); |
| #ifdef CONFIG_PCI_IOV |
| switch (hw->mac.type) { |
| case e1000_82576: |
| case e1000_i350: |
| if (max_vfs > 7) { |
| dev_warn(&pdev->dev, |
| "Maximum of 7 VFs per PF, using max\n"); |
| max_vfs = adapter->vfs_allocated_count = 7; |
| } else |
| adapter->vfs_allocated_count = max_vfs; |
| if (adapter->vfs_allocated_count) |
| dev_warn(&pdev->dev, |
| "Enabling SR-IOV VFs using the module parameter is deprecated - please use the pci sysfs interface.\n"); |
| break; |
| default: |
| break; |
| } |
| #endif /* CONFIG_PCI_IOV */ |
| |
| /* Assume MSI-X interrupts, will be checked during IRQ allocation */ |
| adapter->flags |= IGB_FLAG_HAS_MSIX; |
| |
| adapter->mac_table = kcalloc(hw->mac.rar_entry_count, |
| sizeof(struct igb_mac_addr), |
| GFP_KERNEL); |
| if (!adapter->mac_table) |
| return -ENOMEM; |
| |
| igb_probe_vfs(adapter); |
| |
| igb_init_queue_configuration(adapter); |
| |
| /* Setup and initialize a copy of the hw vlan table array */ |
| adapter->shadow_vfta = kcalloc(E1000_VLAN_FILTER_TBL_SIZE, sizeof(u32), |
| GFP_KERNEL); |
| if (!adapter->shadow_vfta) |
| return -ENOMEM; |
| |
| /* This call may decrease the number of queues */ |
| if (igb_init_interrupt_scheme(adapter, true)) { |
| dev_err(&pdev->dev, "Unable to allocate memory for queues\n"); |
| return -ENOMEM; |
| } |
| |
| /* Explicitly disable IRQ since the NIC can be in any state. */ |
| igb_irq_disable(adapter); |
| |
| if (hw->mac.type >= e1000_i350) |
| adapter->flags &= ~IGB_FLAG_DMAC; |
| |
| set_bit(__IGB_DOWN, &adapter->state); |
| return 0; |
| } |
| |
| /** |
| * __igb_open - Called when a network interface is made active |
| * @netdev: network interface device structure |
| * @resuming: indicates whether we are in a resume call |
| * |
| * Returns 0 on success, negative value on failure |
| * |
| * The open entry point is called when a network interface is made |
| * active by the system (IFF_UP). At this point all resources needed |
| * for transmit and receive operations are allocated, the interrupt |
| * handler is registered with the OS, the watchdog timer is started, |
| * and the stack is notified that the interface is ready. |
| **/ |
| static int __igb_open(struct net_device *netdev, bool resuming) |
| { |
| struct igb_adapter *adapter = netdev_priv(netdev); |
| struct e1000_hw *hw = &adapter->hw; |
| struct pci_dev *pdev = adapter->pdev; |
| int err; |
| int i; |
| |
| /* disallow open during test */ |
| if (test_bit(__IGB_TESTING, &adapter->state)) { |
| WARN_ON(resuming); |
| return -EBUSY; |
| } |
| |
| if (!resuming) |
| pm_runtime_get_sync(&pdev->dev); |
| |
| netif_carrier_off(netdev); |
| |
| /* allocate transmit descriptors */ |
| err = igb_setup_all_tx_resources(adapter); |
| if (err) |
| goto err_setup_tx; |
| |
| /* allocate receive descriptors */ |
| err = igb_setup_all_rx_resources(adapter); |
| if (err) |
| goto err_setup_rx; |
| |
| igb_power_up_link(adapter); |
| |
| /* before we allocate an interrupt, we must be ready to handle it. |
| * Setting DEBUG_SHIRQ in the kernel makes it fire an interrupt |
| * as soon as we call pci_request_irq, so we have to setup our |
| * clean_rx handler before we do so. |
| */ |
| igb_configure(adapter); |
| |
| err = igb_request_irq(adapter); |
| if (err) |
| goto err_req_irq; |
| |
| /* Notify the stack of the actual queue counts. */ |
| err = netif_set_real_num_tx_queues(adapter->netdev, |
| adapter->num_tx_queues); |
| if (err) |
| goto err_set_queues; |
| |
| err = netif_set_real_num_rx_queues(adapter->netdev, |
| adapter->num_rx_queues); |
| if (err) |
| goto err_set_queues; |
| |
| /* From here on the code is the same as igb_up() */ |
| clear_bit(__IGB_DOWN, &adapter->state); |
| |
| for (i = 0; i < adapter->num_q_vectors; i++) |
| napi_enable(&(adapter->q_vector[i]->napi)); |
| |
| /* Clear any pending interrupts. */ |
| rd32(E1000_TSICR); |
| rd32(E1000_ICR); |
| |
| igb_irq_enable(adapter); |
| |
| /* notify VFs that reset has been completed */ |
| if (adapter->vfs_allocated_count) { |
| u32 reg_data = rd32(E1000_CTRL_EXT); |
| |
| reg_data |= E1000_CTRL_EXT_PFRSTD; |
| wr32(E1000_CTRL_EXT, reg_data); |
| } |
| |
| netif_tx_start_all_queues(netdev); |
| |
| if (!resuming) |
| pm_runtime_put(&pdev->dev); |
| |
| /* start the watchdog. */ |
| hw->mac.get_link_status = 1; |
| schedule_work(&adapter->watchdog_task); |
| |
| return 0; |
| |
| err_set_queues: |
| igb_free_irq(adapter); |
| err_req_irq: |
| igb_release_hw_control(adapter); |
| igb_power_down_link(adapter); |
| igb_free_all_rx_resources(adapter); |
| err_setup_rx: |
| igb_free_all_tx_resources(adapter); |
| err_setup_tx: |
| igb_reset(adapter); |
| if (!resuming) |
| pm_runtime_put(&pdev->dev); |
| |
| return err; |
| } |
| |
| int igb_open(struct net_device *netdev) |
| { |
| return __igb_open(netdev, false); |
| } |
| |
| /** |
| * __igb_close - Disables a network interface |
| * @netdev: network interface device structure |
| * @suspending: indicates we are in a suspend call |
| * |
| * Returns 0, this is not allowed to fail |
| * |
| * The close entry point is called when an interface is de-activated |
| * by the OS. The hardware is still under the driver's control, but |
| * needs to be disabled. A global MAC reset is issued to stop the |
| * hardware, and all transmit and receive resources are freed. |
| **/ |
| static int __igb_close(struct net_device *netdev, bool suspending) |
| { |
| struct igb_adapter *adapter = netdev_priv(netdev); |
| struct pci_dev *pdev = adapter->pdev; |
| |
| WARN_ON(test_bit(__IGB_RESETTING, &adapter->state)); |
| |
| if (!suspending) |
| pm_runtime_get_sync(&pdev->dev); |
| |
| igb_down(adapter); |
| igb_free_irq(adapter); |
| |
| igb_free_all_tx_resources(adapter); |
| igb_free_all_rx_resources(adapter); |
| |
| if (!suspending) |
| pm_runtime_put_sync(&pdev->dev); |
| return 0; |
| } |
| |
| int igb_close(struct net_device *netdev) |
| { |
| if (netif_device_present(netdev) || netdev->dismantle) |
| return __igb_close(netdev, false); |
| return 0; |
| } |
| |
| /** |
| * igb_setup_tx_resources - allocate Tx resources (Descriptors) |
| * @tx_ring: tx descriptor ring (for a specific queue) to setup |
| * |
| * Return 0 on success, negative on failure |
| **/ |
| int igb_setup_tx_resources(struct igb_ring *tx_ring) |
| { |
| struct device *dev = tx_ring->dev; |
| int size; |
| |
| size = sizeof(struct igb_tx_buffer) * tx_ring->count; |
| |
| tx_ring->tx_buffer_info = vmalloc(size); |
| if (!tx_ring->tx_buffer_info) |
| goto err; |
| |
| /* round up to nearest 4K */ |
| tx_ring->size = tx_ring->count * sizeof(union e1000_adv_tx_desc); |
| tx_ring->size = ALIGN(tx_ring->size, 4096); |
| |
| tx_ring->desc = dma_alloc_coherent(dev, tx_ring->size, |
| &tx_ring->dma, GFP_KERNEL); |
| if (!tx_ring->desc) |
| goto err; |
| |
| tx_ring->next_to_use = 0; |
| tx_ring->next_to_clean = 0; |
| |
| return 0; |
| |
| err: |
| vfree(tx_ring->tx_buffer_info); |
| tx_ring->tx_buffer_info = NULL; |
| dev_err(dev, "Unable to allocate memory for the Tx descriptor ring\n"); |
| return -ENOMEM; |
| } |
| |
| /** |
| * igb_setup_all_tx_resources - wrapper to allocate Tx resources |
| * (Descriptors) for all queues |
| * @adapter: board private structure |
| * |
| * Return 0 on success, negative on failure |
| **/ |
| static int igb_setup_all_tx_resources(struct igb_adapter *adapter) |
| { |
| struct pci_dev *pdev = adapter->pdev; |
| int i, err = 0; |
| |
| for (i = 0; i < adapter->num_tx_queues; i++) { |
| err = igb_setup_tx_resources(adapter->tx_ring[i]); |
| if (err) { |
| dev_err(&pdev->dev, |
| "Allocation for Tx Queue %u failed\n", i); |
| for (i--; i >= 0; i--) |
| igb_free_tx_resources(adapter->tx_ring[i]); |
| break; |
| } |
| } |
| |
| return err; |
| } |
| |
| /** |
| * igb_setup_tctl - configure the transmit control registers |
| * @adapter: Board private structure |
| **/ |
| void igb_setup_tctl(struct igb_adapter *adapter) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| u32 tctl; |
| |
| /* disable queue 0 which is enabled by default on 82575 and 82576 */ |
| wr32(E1000_TXDCTL(0), 0); |
| |
| /* Program the Transmit Control Register */ |
| tctl = rd32(E1000_TCTL); |
| tctl &= ~E1000_TCTL_CT; |
| tctl |= E1000_TCTL_PSP | E1000_TCTL_RTLC | |
| (E1000_COLLISION_THRESHOLD << E1000_CT_SHIFT); |
| |
| igb_config_collision_dist(hw); |
| |
| /* Enable transmits */ |
| tctl |= E1000_TCTL_EN; |
| |
| wr32(E1000_TCTL, tctl); |
| } |
| |
| /** |
| * igb_configure_tx_ring - Configure transmit ring after Reset |
| * @adapter: board private structure |
| * @ring: tx ring to configure |
| * |
| * Configure a transmit ring after a reset. |
| **/ |
| void igb_configure_tx_ring(struct igb_adapter *adapter, |
| struct igb_ring *ring) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| u32 txdctl = 0; |
| u64 tdba = ring->dma; |
| int reg_idx = ring->reg_idx; |
| |
| wr32(E1000_TDLEN(reg_idx), |
| ring->count * sizeof(union e1000_adv_tx_desc)); |
| wr32(E1000_TDBAL(reg_idx), |
| tdba & 0x00000000ffffffffULL); |
| wr32(E1000_TDBAH(reg_idx), tdba >> 32); |
| |
| ring->tail = adapter->io_addr + E1000_TDT(reg_idx); |
| wr32(E1000_TDH(reg_idx), 0); |
| writel(0, ring->tail); |
| |
| txdctl |= IGB_TX_PTHRESH; |
| txdctl |= IGB_TX_HTHRESH << 8; |
| txdctl |= IGB_TX_WTHRESH << 16; |
| |
| /* reinitialize tx_buffer_info */ |
| memset(ring->tx_buffer_info, 0, |
| sizeof(struct igb_tx_buffer) * ring->count); |
| |
| txdctl |= E1000_TXDCTL_QUEUE_ENABLE; |
| wr32(E1000_TXDCTL(reg_idx), txdctl); |
| } |
| |
| /** |
| * igb_configure_tx - Configure transmit Unit after Reset |
| * @adapter: board private structure |
| * |
| * Configure the Tx unit of the MAC after a reset. |
| **/ |
| static void igb_configure_tx(struct igb_adapter *adapter) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| int i; |
| |
| /* disable the queues */ |
| for (i = 0; i < adapter->num_tx_queues; i++) |
| wr32(E1000_TXDCTL(adapter->tx_ring[i]->reg_idx), 0); |
| |
| wrfl(); |
| usleep_range(10000, 20000); |
| |
| for (i = 0; i < adapter->num_tx_queues; i++) |
| igb_configure_tx_ring(adapter, adapter->tx_ring[i]); |
| } |
| |
| /** |
| * igb_setup_rx_resources - allocate Rx resources (Descriptors) |
| * @rx_ring: Rx descriptor ring (for a specific queue) to setup |
| * |
| * Returns 0 on success, negative on failure |
| **/ |
| int igb_setup_rx_resources(struct igb_ring *rx_ring) |
| { |
| struct igb_adapter *adapter = netdev_priv(rx_ring->netdev); |
| struct device *dev = rx_ring->dev; |
| int size, res; |
| |
| /* XDP RX-queue info */ |
| if (xdp_rxq_info_is_reg(&rx_ring->xdp_rxq)) |
| xdp_rxq_info_unreg(&rx_ring->xdp_rxq); |
| res = xdp_rxq_info_reg(&rx_ring->xdp_rxq, rx_ring->netdev, |
| rx_ring->queue_index, 0); |
| if (res < 0) { |
| dev_err(dev, "Failed to register xdp_rxq index %u\n", |
| rx_ring->queue_index); |
| return res; |
| } |
| |
| size = sizeof(struct igb_rx_buffer) * rx_ring->count; |
| |
| rx_ring->rx_buffer_info = vmalloc(size); |
| if (!rx_ring->rx_buffer_info) |
| goto err; |
| |
| /* Round up to nearest 4K */ |
| rx_ring->size = rx_ring->count * sizeof(union e1000_adv_rx_desc); |
| rx_ring->size = ALIGN(rx_ring->size, 4096); |
| |
| rx_ring->desc = dma_alloc_coherent(dev, rx_ring->size, |
| &rx_ring->dma, GFP_KERNEL); |
| if (!rx_ring->desc) |
| goto err; |
| |
| rx_ring->next_to_alloc = 0; |
| rx_ring->next_to_clean = 0; |
| rx_ring->next_to_use = 0; |
| |
| rx_ring->xdp_prog = adapter->xdp_prog; |
| |
| return 0; |
| |
| err: |
| xdp_rxq_info_unreg(&rx_ring->xdp_rxq); |
| vfree(rx_ring->rx_buffer_info); |
| rx_ring->rx_buffer_info = NULL; |
| dev_err(dev, "Unable to allocate memory for the Rx descriptor ring\n"); |
| return -ENOMEM; |
| } |
| |
| /** |
| * igb_setup_all_rx_resources - wrapper to allocate Rx resources |
| * (Descriptors) for all queues |
| * @adapter: board private structure |
| * |
| * Return 0 on success, negative on failure |
| **/ |
| static int igb_setup_all_rx_resources(struct igb_adapter *adapter) |
| { |
| struct pci_dev *pdev = adapter->pdev; |
| int i, err = 0; |
| |
| for (i = 0; i < adapter->num_rx_queues; i++) { |
| err = igb_setup_rx_resources(adapter->rx_ring[i]); |
| if (err) { |
| dev_err(&pdev->dev, |
| "Allocation for Rx Queue %u failed\n", i); |
| for (i--; i >= 0; i--) |
| igb_free_rx_resources(adapter->rx_ring[i]); |
| break; |
| } |
| } |
| |
| return err; |
| } |
| |
| /** |
| * igb_setup_mrqc - configure the multiple receive queue control registers |
| * @adapter: Board private structure |
| **/ |
| static void igb_setup_mrqc(struct igb_adapter *adapter) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| u32 mrqc, rxcsum; |
| u32 j, num_rx_queues; |
| u32 rss_key[10]; |
| |
| netdev_rss_key_fill(rss_key, sizeof(rss_key)); |
| for (j = 0; j < 10; j++) |
| wr32(E1000_RSSRK(j), rss_key[j]); |
| |
| num_rx_queues = adapter->rss_queues; |
| |
| switch (hw->mac.type) { |
| case e1000_82576: |
| /* 82576 supports 2 RSS queues for SR-IOV */ |
| if (adapter->vfs_allocated_count) |
| num_rx_queues = 2; |
| break; |
| default: |
| break; |
| } |
| |
| if (adapter->rss_indir_tbl_init != num_rx_queues) { |
| for (j = 0; j < IGB_RETA_SIZE; j++) |
| adapter->rss_indir_tbl[j] = |
| (j * num_rx_queues) / IGB_RETA_SIZE; |
| adapter->rss_indir_tbl_init = num_rx_queues; |
| } |
| igb_write_rss_indir_tbl(adapter); |
| |
| /* Disable raw packet checksumming so that RSS hash is placed in |
| * descriptor on writeback. No need to enable TCP/UDP/IP checksum |
| * offloads as they are enabled by default |
| */ |
| rxcsum = rd32(E1000_RXCSUM); |
| rxcsum |= E1000_RXCSUM_PCSD; |
| |
| if (adapter->hw.mac.type >= e1000_82576) |
| /* Enable Receive Checksum Offload for SCTP */ |
| rxcsum |= E1000_RXCSUM_CRCOFL; |
| |
| /* Don't need to set TUOFL or IPOFL, they default to 1 */ |
| wr32(E1000_RXCSUM, rxcsum); |
| |
| /* Generate RSS hash based on packet types, TCP/UDP |
| * port numbers and/or IPv4/v6 src and dst addresses |
| */ |
| mrqc = E1000_MRQC_RSS_FIELD_IPV4 | |
| E1000_MRQC_RSS_FIELD_IPV4_TCP | |
| E1000_MRQC_RSS_FIELD_IPV6 | |
| E1000_MRQC_RSS_FIELD_IPV6_TCP | |
| E1000_MRQC_RSS_FIELD_IPV6_TCP_EX; |
| |
| if (adapter->flags & IGB_FLAG_RSS_FIELD_IPV4_UDP) |
| mrqc |= E1000_MRQC_RSS_FIELD_IPV4_UDP; |
| if (adapter->flags & IGB_FLAG_RSS_FIELD_IPV6_UDP) |
| mrqc |= E1000_MRQC_RSS_FIELD_IPV6_UDP; |
| |
| /* If VMDq is enabled then we set the appropriate mode for that, else |
| * we default to RSS so that an RSS hash is calculated per packet even |
| * if we are only using one queue |
| */ |
| if (adapter->vfs_allocated_count) { |
| if (hw->mac.type > e1000_82575) { |
| /* Set the default pool for the PF's first queue */ |
| u32 vtctl = rd32(E1000_VT_CTL); |
| |
| vtctl &= ~(E1000_VT_CTL_DEFAULT_POOL_MASK | |
| E1000_VT_CTL_DISABLE_DEF_POOL); |
| vtctl |= adapter->vfs_allocated_count << |
| E1000_VT_CTL_DEFAULT_POOL_SHIFT; |
| wr32(E1000_VT_CTL, vtctl); |
| } |
| if (adapter->rss_queues > 1) |
| mrqc |= E1000_MRQC_ENABLE_VMDQ_RSS_MQ; |
| else |
| mrqc |= E1000_MRQC_ENABLE_VMDQ; |
| } else { |
| mrqc |= E1000_MRQC_ENABLE_RSS_MQ; |
| } |
| igb_vmm_control(adapter); |
| |
| wr32(E1000_MRQC, mrqc); |
| } |
| |
| /** |
| * igb_setup_rctl - configure the receive control registers |
| * @adapter: Board private structure |
| **/ |
| void igb_setup_rctl(struct igb_adapter *adapter) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| u32 rctl; |
| |
| rctl = rd32(E1000_RCTL); |
| |
| rctl &= ~(3 << E1000_RCTL_MO_SHIFT); |
| rctl &= ~(E1000_RCTL_LBM_TCVR | E1000_RCTL_LBM_MAC); |
| |
| rctl |= E1000_RCTL_EN | E1000_RCTL_BAM | E1000_RCTL_RDMTS_HALF | |
| (hw->mac.mc_filter_type << E1000_RCTL_MO_SHIFT); |
| |
| /* enable stripping of CRC. It's unlikely this will break BMC |
| * redirection as it did with e1000. Newer features require |
| * that the HW strips the CRC. |
| */ |
| rctl |= E1000_RCTL_SECRC; |
| |
| /* disable store bad packets and clear size bits. */ |
| rctl &= ~(E1000_RCTL_SBP | E1000_RCTL_SZ_256); |
| |
| /* enable LPE to allow for reception of jumbo frames */ |
| rctl |= E1000_RCTL_LPE; |
| |
| /* disable queue 0 to prevent tail write w/o re-config */ |
| wr32(E1000_RXDCTL(0), 0); |
| |
| /* Attention!!! For SR-IOV PF driver operations you must enable |
| * queue drop for all VF and PF queues to prevent head of line blocking |
| * if an un-trusted VF does not provide descriptors to hardware. |
| */ |
| if (adapter->vfs_allocated_count) { |
| /* set all queue drop enable bits */ |
| wr32(E1000_QDE, ALL_QUEUES); |
| } |
| |
| /* This is useful for sniffing bad packets. */ |
| if (adapter->netdev->features & NETIF_F_RXALL) { |
| /* UPE and MPE will be handled by normal PROMISC logic |
| * in e1000e_set_rx_mode |
| */ |
| rctl |= (E1000_RCTL_SBP | /* Receive bad packets */ |
| E1000_RCTL_BAM | /* RX All Bcast Pkts */ |
| E1000_RCTL_PMCF); /* RX All MAC Ctrl Pkts */ |
| |
| rctl &= ~(E1000_RCTL_DPF | /* Allow filtered pause */ |
| E1000_RCTL_CFIEN); /* Dis VLAN CFIEN Filter */ |
| /* Do not mess with E1000_CTRL_VME, it affects transmit as well, |
| * and that breaks VLANs. |
| */ |
| } |
| |
| wr32(E1000_RCTL, rctl); |
| } |
| |
| static inline int igb_set_vf_rlpml(struct igb_adapter *adapter, int size, |
| int vfn) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| u32 vmolr; |
| |
| if (size > MAX_JUMBO_FRAME_SIZE) |
| size = MAX_JUMBO_FRAME_SIZE; |
| |
| vmolr = rd32(E1000_VMOLR(vfn)); |
| vmolr &= ~E1000_VMOLR_RLPML_MASK; |
| vmolr |= size | E1000_VMOLR_LPE; |
| wr32(E1000_VMOLR(vfn), vmolr); |
| |
| return 0; |
| } |
| |
| static inline void igb_set_vf_vlan_strip(struct igb_adapter *adapter, |
| int vfn, bool enable) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| u32 val, reg; |
| |
| if (hw->mac.type < e1000_82576) |
| return; |
| |
| if (hw->mac.type == e1000_i350) |
| reg = E1000_DVMOLR(vfn); |
| else |
| reg = E1000_VMOLR(vfn); |
| |
| val = rd32(reg); |
| if (enable) |
| val |= E1000_VMOLR_STRVLAN; |
| else |
| val &= ~(E1000_VMOLR_STRVLAN); |
| wr32(reg, val); |
| } |
| |
| static inline void igb_set_vmolr(struct igb_adapter *adapter, |
| int vfn, bool aupe) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| u32 vmolr; |
| |
| /* This register exists only on 82576 and newer so if we are older then |
| * we should exit and do nothing |
| */ |
| if (hw->mac.type < e1000_82576) |
| return; |
| |
| vmolr = rd32(E1000_VMOLR(vfn)); |
| if (aupe) |
| vmolr |= E1000_VMOLR_AUPE; /* Accept untagged packets */ |
| else |
| vmolr &= ~(E1000_VMOLR_AUPE); /* Tagged packets ONLY */ |
| |
| /* clear all bits that might not be set */ |
| vmolr &= ~(E1000_VMOLR_BAM | E1000_VMOLR_RSSE); |
| |
| if (adapter->rss_queues > 1 && vfn == adapter->vfs_allocated_count) |
| vmolr |= E1000_VMOLR_RSSE; /* enable RSS */ |
| /* for VMDq only allow the VFs and pool 0 to accept broadcast and |
| * multicast packets |
| */ |
| if (vfn <= adapter->vfs_allocated_count) |
| vmolr |= E1000_VMOLR_BAM; /* Accept broadcast */ |
| |
| wr32(E1000_VMOLR(vfn), vmolr); |
| } |
| |
| /** |
| * igb_setup_srrctl - configure the split and replication receive control |
| * registers |
| * @adapter: Board private structure |
| * @ring: receive ring to be configured |
| **/ |
| void igb_setup_srrctl(struct igb_adapter *adapter, struct igb_ring *ring) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| int reg_idx = ring->reg_idx; |
| u32 srrctl = 0; |
| |
| srrctl = IGB_RX_HDR_LEN << E1000_SRRCTL_BSIZEHDRSIZE_SHIFT; |
| if (ring_uses_large_buffer(ring)) |
| srrctl |= IGB_RXBUFFER_3072 >> E1000_SRRCTL_BSIZEPKT_SHIFT; |
| else |
| srrctl |= IGB_RXBUFFER_2048 >> E1000_SRRCTL_BSIZEPKT_SHIFT; |
| srrctl |= E1000_SRRCTL_DESCTYPE_ADV_ONEBUF; |
| if (hw->mac.type >= e1000_82580) |
| srrctl |= E1000_SRRCTL_TIMESTAMP; |
| /* Only set Drop Enable if VFs allocated, or we are supporting multiple |
| * queues and rx flow control is disabled |
| */ |
| if (adapter->vfs_allocated_count || |
| (!(hw->fc.current_mode & e1000_fc_rx_pause) && |
| adapter->num_rx_queues > 1)) |
| srrctl |= E1000_SRRCTL_DROP_EN; |
| |
| wr32(E1000_SRRCTL(reg_idx), srrctl); |
| } |
| |
| /** |
| * igb_configure_rx_ring - Configure a receive ring after Reset |
| * @adapter: board private structure |
| * @ring: receive ring to be configured |
| * |
| * Configure the Rx unit of the MAC after a reset. |
| **/ |
| void igb_configure_rx_ring(struct igb_adapter *adapter, |
| struct igb_ring *ring) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| union e1000_adv_rx_desc *rx_desc; |
| u64 rdba = ring->dma; |
| int reg_idx = ring->reg_idx; |
| u32 rxdctl = 0; |
| |
| xdp_rxq_info_unreg_mem_model(&ring->xdp_rxq); |
| WARN_ON(xdp_rxq_info_reg_mem_model(&ring->xdp_rxq, |
| MEM_TYPE_PAGE_SHARED, NULL)); |
| |
| /* disable the queue */ |
| wr32(E1000_RXDCTL(reg_idx), 0); |
| |
| /* Set DMA base address registers */ |
| wr32(E1000_RDBAL(reg_idx), |
| rdba & 0x00000000ffffffffULL); |
| wr32(E1000_RDBAH(reg_idx), rdba >> 32); |
| wr32(E1000_RDLEN(reg_idx), |
| ring->count * sizeof(union e1000_adv_rx_desc)); |
| |
| /* initialize head and tail */ |
| ring->tail = adapter->io_addr + E1000_RDT(reg_idx); |
| wr32(E1000_RDH(reg_idx), 0); |
| writel(0, ring->tail); |
| |
| /* set descriptor configuration */ |
| igb_setup_srrctl(adapter, ring); |
| |
| /* set filtering for VMDQ pools */ |
| igb_set_vmolr(adapter, reg_idx & 0x7, true); |
| |
| rxdctl |= IGB_RX_PTHRESH; |
| rxdctl |= IGB_RX_HTHRESH << 8; |
| rxdctl |= IGB_RX_WTHRESH << 16; |
| |
| /* initialize rx_buffer_info */ |
| memset(ring->rx_buffer_info, 0, |
| sizeof(struct igb_rx_buffer) * ring->count); |
| |
| /* initialize Rx descriptor 0 */ |
| rx_desc = IGB_RX_DESC(ring, 0); |
| rx_desc->wb.upper.length = 0; |
| |
| /* enable receive descriptor fetching */ |
| rxdctl |= E1000_RXDCTL_QUEUE_ENABLE; |
| wr32(E1000_RXDCTL(reg_idx), rxdctl); |
| } |
| |
| static void igb_set_rx_buffer_len(struct igb_adapter *adapter, |
| struct igb_ring *rx_ring) |
| { |
| #if (PAGE_SIZE < 8192) |
| struct e1000_hw *hw = &adapter->hw; |
| #endif |
| |
| /* set build_skb and buffer size flags */ |
| clear_ring_build_skb_enabled(rx_ring); |
| clear_ring_uses_large_buffer(rx_ring); |
| |
| if (adapter->flags & IGB_FLAG_RX_LEGACY) |
| return; |
| |
| set_ring_build_skb_enabled(rx_ring); |
| |
| #if (PAGE_SIZE < 8192) |
| if (adapter->max_frame_size > IGB_MAX_FRAME_BUILD_SKB || |
| IGB_2K_TOO_SMALL_WITH_PADDING || |
| rd32(E1000_RCTL) & E1000_RCTL_SBP) |
| set_ring_uses_large_buffer(rx_ring); |
| #endif |
| } |
| |
| /** |
| * igb_configure_rx - Configure receive Unit after Reset |
| * @adapter: board private structure |
| * |
| * Configure the Rx unit of the MAC after a reset. |
| **/ |
| static void igb_configure_rx(struct igb_adapter *adapter) |
| { |
| int i; |
| |
| /* set the correct pool for the PF default MAC address in entry 0 */ |
| igb_set_default_mac_filter(adapter); |
| |
| /* Setup the HW Rx Head and Tail Descriptor Pointers and |
| * the Base and Length of the Rx Descriptor Ring |
| */ |
| for (i = 0; i < adapter->num_rx_queues; i++) { |
| struct igb_ring *rx_ring = adapter->rx_ring[i]; |
| |
| igb_set_rx_buffer_len(adapter, rx_ring); |
| igb_configure_rx_ring(adapter, rx_ring); |
| } |
| } |
| |
| /** |
| * igb_free_tx_resources - Free Tx Resources per Queue |
| * @tx_ring: Tx descriptor ring for a specific queue |
| * |
| * Free all transmit software resources |
| **/ |
| void igb_free_tx_resources(struct igb_ring *tx_ring) |
| { |
| igb_clean_tx_ring(tx_ring); |
| |
| vfree(tx_ring->tx_buffer_info); |
| tx_ring->tx_buffer_info = NULL; |
| |
| /* if not set, then don't free */ |
| if (!tx_ring->desc) |
| return; |
| |
| dma_free_coherent(tx_ring->dev, tx_ring->size, |
| tx_ring->desc, tx_ring->dma); |
| |
| tx_ring->desc = NULL; |
| } |
| |
| /** |
| * igb_free_all_tx_resources - Free Tx Resources for All Queues |
| * @adapter: board private structure |
| * |
| * Free all transmit software resources |
| **/ |
| static void igb_free_all_tx_resources(struct igb_adapter *adapter) |
| { |
| int i; |
| |
| for (i = 0; i < adapter->num_tx_queues; i++) |
| if (adapter->tx_ring[i]) |
| igb_free_tx_resources(adapter->tx_ring[i]); |
| } |
| |
| /** |
| * igb_clean_tx_ring - Free Tx Buffers |
| * @tx_ring: ring to be cleaned |
| **/ |
| static void igb_clean_tx_ring(struct igb_ring *tx_ring) |
| { |
| u16 i = tx_ring->next_to_clean; |
| struct igb_tx_buffer *tx_buffer = &tx_ring->tx_buffer_info[i]; |
| |
| while (i != tx_ring->next_to_use) { |
| union e1000_adv_tx_desc *eop_desc, *tx_desc; |
| |
| /* Free all the Tx ring sk_buffs or xdp frames */ |
| if (tx_buffer->type == IGB_TYPE_SKB) |
| dev_kfree_skb_any(tx_buffer->skb); |
| else |
| xdp_return_frame(tx_buffer->xdpf); |
| |
| /* unmap skb header data */ |
| dma_unmap_single(tx_ring->dev, |
| dma_unmap_addr(tx_buffer, dma), |
| dma_unmap_len(tx_buffer, len), |
| DMA_TO_DEVICE); |
| |
| /* check for eop_desc to determine the end of the packet */ |
| eop_desc = tx_buffer->next_to_watch; |
| tx_desc = IGB_TX_DESC(tx_ring, i); |
| |
| /* unmap remaining buffers */ |
| while (tx_desc != eop_desc) { |
| tx_buffer++; |
| tx_desc++; |
| i++; |
| if (unlikely(i == tx_ring->count)) { |
| i = 0; |
| tx_buffer = tx_ring->tx_buffer_info; |
| tx_desc = IGB_TX_DESC(tx_ring, 0); |
| } |
| |
| /* unmap any remaining paged data */ |
| if (dma_unmap_len(tx_buffer, len)) |
| dma_unmap_page(tx_ring->dev, |
| dma_unmap_addr(tx_buffer, dma), |
| dma_unmap_len(tx_buffer, len), |
| DMA_TO_DEVICE); |
| } |
| |
| tx_buffer->next_to_watch = NULL; |
| |
| /* move us one more past the eop_desc for start of next pkt */ |
| tx_buffer++; |
| i++; |
| if (unlikely(i == tx_ring->count)) { |
| i = 0; |
| tx_buffer = tx_ring->tx_buffer_info; |
| } |
| } |
| |
| /* reset BQL for queue */ |
| netdev_tx_reset_queue(txring_txq(tx_ring)); |
| |
| /* reset next_to_use and next_to_clean */ |
| tx_ring->next_to_use = 0; |
| tx_ring->next_to_clean = 0; |
| } |
| |
| /** |
| * igb_clean_all_tx_rings - Free Tx Buffers for all queues |
| * @adapter: board private structure |
| **/ |
| static void igb_clean_all_tx_rings(struct igb_adapter *adapter) |
| { |
| int i; |
| |
| for (i = 0; i < adapter->num_tx_queues; i++) |
| if (adapter->tx_ring[i]) |
| igb_clean_tx_ring(adapter->tx_ring[i]); |
| } |
| |
| /** |
| * igb_free_rx_resources - Free Rx Resources |
| * @rx_ring: ring to clean the resources from |
| * |
| * Free all receive software resources |
| **/ |
| void igb_free_rx_resources(struct igb_ring *rx_ring) |
| { |
| igb_clean_rx_ring(rx_ring); |
| |
| rx_ring->xdp_prog = NULL; |
| xdp_rxq_info_unreg(&rx_ring->xdp_rxq); |
| vfree(rx_ring->rx_buffer_info); |
| rx_ring->rx_buffer_info = NULL; |
| |
| /* if not set, then don't free */ |
| if (!rx_ring->desc) |
| return; |
| |
| dma_free_coherent(rx_ring->dev, rx_ring->size, |
| rx_ring->desc, rx_ring->dma); |
| |
| rx_ring->desc = NULL; |
| } |
| |
| /** |
| * igb_free_all_rx_resources - Free Rx Resources for All Queues |
| * @adapter: board private structure |
| * |
| * Free all receive software resources |
| **/ |
| static void igb_free_all_rx_resources(struct igb_adapter *adapter) |
| { |
| int i; |
| |
| for (i = 0; i < adapter->num_rx_queues; i++) |
| if (adapter->rx_ring[i]) |
| igb_free_rx_resources(adapter->rx_ring[i]); |
| } |
| |
| /** |
| * igb_clean_rx_ring - Free Rx Buffers per Queue |
| * @rx_ring: ring to free buffers from |
| **/ |
| static void igb_clean_rx_ring(struct igb_ring *rx_ring) |
| { |
| u16 i = rx_ring->next_to_clean; |
| |
| dev_kfree_skb(rx_ring->skb); |
| rx_ring->skb = NULL; |
| |
| /* Free all the Rx ring sk_buffs */ |
| while (i != rx_ring->next_to_alloc) { |
| struct igb_rx_buffer *buffer_info = &rx_ring->rx_buffer_info[i]; |
| |
| /* Invalidate cache lines that may have been written to by |
| * device so that we avoid corrupting memory. |
| */ |
| dma_sync_single_range_for_cpu(rx_ring->dev, |
| buffer_info->dma, |
| buffer_info->page_offset, |
| igb_rx_bufsz(rx_ring), |
| DMA_FROM_DEVICE); |
| |
| /* free resources associated with mapping */ |
| dma_unmap_page_attrs(rx_ring->dev, |
| buffer_info->dma, |
| igb_rx_pg_size(rx_ring), |
| DMA_FROM_DEVICE, |
| IGB_RX_DMA_ATTR); |
| __page_frag_cache_drain(buffer_info->page, |
| buffer_info->pagecnt_bias); |
| |
| i++; |
| if (i == rx_ring->count) |
| i = 0; |
| } |
| |
| rx_ring->next_to_alloc = 0; |
| rx_ring->next_to_clean = 0; |
| rx_ring->next_to_use = 0; |
| } |
| |
| /** |
| * igb_clean_all_rx_rings - Free Rx Buffers for all queues |
| * @adapter: board private structure |
| **/ |
| static void igb_clean_all_rx_rings(struct igb_adapter *adapter) |
| { |
| int i; |
| |
| for (i = 0; i < adapter->num_rx_queues; i++) |
| if (adapter->rx_ring[i]) |
| igb_clean_rx_ring(adapter->rx_ring[i]); |
| } |
| |
| /** |
| * igb_set_mac - Change the Ethernet Address of the NIC |
| * @netdev: network interface device structure |
| * @p: pointer to an address structure |
| * |
| * Returns 0 on success, negative on failure |
| **/ |
| static int igb_set_mac(struct net_device *netdev, void *p) |
| { |
| struct igb_adapter *adapter = netdev_priv(netdev); |
| struct e1000_hw *hw = &adapter->hw; |
| struct sockaddr *addr = p; |
| |
| if (!is_valid_ether_addr(addr->sa_data)) |
| return -EADDRNOTAVAIL; |
| |
| eth_hw_addr_set(netdev, addr->sa_data); |
| memcpy(hw->mac.addr, addr->sa_data, netdev->addr_len); |
| |
| /* set the correct pool for the new PF MAC address in entry 0 */ |
| igb_set_default_mac_filter(adapter); |
| |
| return 0; |
| } |
| |
| /** |
| * igb_write_mc_addr_list - write multicast addresses to MTA |
| * @netdev: network interface device structure |
| * |
| * Writes multicast address list to the MTA hash table. |
| * Returns: -ENOMEM on failure |
| * 0 on no addresses written |
| * X on writing X addresses to MTA |
| **/ |
| static int igb_write_mc_addr_list(struct net_device *netdev) |
| { |
| struct igb_adapter *adapter = netdev_priv(netdev); |
| struct e1000_hw *hw = &adapter->hw; |
| struct netdev_hw_addr *ha; |
| u8 *mta_list; |
| int i; |
| |
| if (netdev_mc_empty(netdev)) { |
| /* nothing to program, so clear mc list */ |
| igb_update_mc_addr_list(hw, NULL, 0); |
| igb_restore_vf_multicasts(adapter); |
| return 0; |
| } |
| |
| mta_list = kcalloc(netdev_mc_count(netdev), 6, GFP_ATOMIC); |
| if (!mta_list) |
| return -ENOMEM; |
| |
| /* The shared function expects a packed array of only addresses. */ |
| i = 0; |
| netdev_for_each_mc_addr(ha, netdev) |
| memcpy(mta_list + (i++ * ETH_ALEN), ha->addr, ETH_ALEN); |
| |
| igb_update_mc_addr_list(hw, mta_list, i); |
| kfree(mta_list); |
| |
| return netdev_mc_count(netdev); |
| } |
| |
| static int igb_vlan_promisc_enable(struct igb_adapter *adapter) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| u32 i, pf_id; |
| |
| switch (hw->mac.type) { |
| case e1000_i210: |
| case e1000_i211: |
| case e1000_i350: |
| /* VLAN filtering needed for VLAN prio filter */ |
| if (adapter->netdev->features & NETIF_F_NTUPLE) |
| break; |
| fallthrough; |
| case e1000_82576: |
| case e1000_82580: |
| case e1000_i354: |
| /* VLAN filtering needed for pool filtering */ |
| if (adapter->vfs_allocated_count) |
| break; |
| fallthrough; |
| default: |
| return 1; |
| } |
| |
| /* We are already in VLAN promisc, nothing to do */ |
| if (adapter->flags & IGB_FLAG_VLAN_PROMISC) |
| return 0; |
| |
| if (!adapter->vfs_allocated_count) |
| goto set_vfta; |
| |
| /* Add PF to all active pools */ |
| pf_id = adapter->vfs_allocated_count + E1000_VLVF_POOLSEL_SHIFT; |
| |
| for (i = E1000_VLVF_ARRAY_SIZE; --i;) { |
| u32 vlvf = rd32(E1000_VLVF(i)); |
| |
| vlvf |= BIT(pf_id); |
| wr32(E1000_VLVF(i), vlvf); |
| } |
| |
| set_vfta: |
| /* Set all bits in the VLAN filter table array */ |
| for (i = E1000_VLAN_FILTER_TBL_SIZE; i--;) |
| hw->mac.ops.write_vfta(hw, i, ~0U); |
| |
| /* Set flag so we don't redo unnecessary work */ |
| adapter->flags |= IGB_FLAG_VLAN_PROMISC; |
| |
| return 0; |
| } |
| |
| #define VFTA_BLOCK_SIZE 8 |
| static void igb_scrub_vfta(struct igb_adapter *adapter, u32 vfta_offset) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| u32 vfta[VFTA_BLOCK_SIZE] = { 0 }; |
| u32 vid_start = vfta_offset * 32; |
| u32 vid_end = vid_start + (VFTA_BLOCK_SIZE * 32); |
| u32 i, vid, word, bits, pf_id; |
| |
| /* guarantee that we don't scrub out management VLAN */ |
| vid = adapter->mng_vlan_id; |
| if (vid >= vid_start && vid < vid_end) |
| vfta[(vid - vid_start) / 32] |= BIT(vid % 32); |
| |
| if (!adapter->vfs_allocated_count) |
| goto set_vfta; |
| |
| pf_id = adapter->vfs_allocated_count + E1000_VLVF_POOLSEL_SHIFT; |
| |
| for (i = E1000_VLVF_ARRAY_SIZE; --i;) { |
| u32 vlvf = rd32(E1000_VLVF(i)); |
| |
| /* pull VLAN ID from VLVF */ |
| vid = vlvf & VLAN_VID_MASK; |
| |
| /* only concern ourselves with a certain range */ |
| if (vid < vid_start || vid >= vid_end) |
| continue; |
| |
| if (vlvf & E1000_VLVF_VLANID_ENABLE) { |
| /* record VLAN ID in VFTA */ |
| vfta[(vid - vid_start) / 32] |= BIT(vid % 32); |
| |
| /* if PF is part of this then continue */ |
| if (test_bit(vid, adapter->active_vlans)) |
| continue; |
| } |
| |
| /* remove PF from the pool */ |
| bits = ~BIT(pf_id); |
| bits &= rd32(E1000_VLVF(i)); |
| wr32(E1000_VLVF(i), bits); |
| } |
| |
| set_vfta: |
| /* extract values from active_vlans and write back to VFTA */ |
| for (i = VFTA_BLOCK_SIZE; i--;) { |
| vid = (vfta_offset + i) * 32; |
| word = vid / BITS_PER_LONG; |
| bits = vid % BITS_PER_LONG; |
| |
| vfta[i] |= adapter->active_vlans[word] >> bits; |
| |
| hw->mac.ops.write_vfta(hw, vfta_offset + i, vfta[i]); |
| } |
| } |
| |
| static void igb_vlan_promisc_disable(struct igb_adapter *adapter) |
| { |
| u32 i; |
| |
| /* We are not in VLAN promisc, nothing to do */ |
| if (!(adapter->flags & IGB_FLAG_VLAN_PROMISC)) |
| return; |
| |
| /* Set flag so we don't redo unnecessary work */ |
| adapter->flags &= ~IGB_FLAG_VLAN_PROMISC; |
| |
| for (i = 0; i < E1000_VLAN_FILTER_TBL_SIZE; i += VFTA_BLOCK_SIZE) |
| igb_scrub_vfta(adapter, i); |
| } |
| |
| /** |
| * igb_set_rx_mode - Secondary Unicast, Multicast and Promiscuous mode set |
| * @netdev: network interface device structure |
| * |
| * The set_rx_mode entry point is called whenever the unicast or multicast |
| * address lists or the network interface flags are updated. This routine is |
| * responsible for configuring the hardware for proper unicast, multicast, |
| * promiscuous mode, and all-multi behavior. |
| **/ |
| static void igb_set_rx_mode(struct net_device *netdev) |
| { |
| struct igb_adapter *adapter = netdev_priv(netdev); |
| struct e1000_hw *hw = &adapter->hw; |
| unsigned int vfn = adapter->vfs_allocated_count; |
| u32 rctl = 0, vmolr = 0, rlpml = MAX_JUMBO_FRAME_SIZE; |
| int count; |
| |
| /* Check for Promiscuous and All Multicast modes */ |
| if (netdev->flags & IFF_PROMISC) { |
| rctl |= E1000_RCTL_UPE | E1000_RCTL_MPE; |
| vmolr |= E1000_VMOLR_MPME; |
| |
| /* enable use of UTA filter to force packets to default pool */ |
| if (hw->mac.type == e1000_82576) |
| vmolr |= E1000_VMOLR_ROPE; |
| } else { |
| if (netdev->flags & IFF_ALLMULTI) { |
| rctl |= E1000_RCTL_MPE; |
| vmolr |= E1000_VMOLR_MPME; |
| } else { |
| /* Write addresses to the MTA, if the attempt fails |
| * then we should just turn on promiscuous mode so |
| * that we can at least receive multicast traffic |
| */ |
| count = igb_write_mc_addr_list(netdev); |
| if (count < 0) { |
| rctl |= E1000_RCTL_MPE; |
| vmolr |= E1000_VMOLR_MPME; |
| } else if (count) { |
| vmolr |= E1000_VMOLR_ROMPE; |
| } |
| } |
| } |
| |
| /* Write addresses to available RAR registers, if there is not |
| * sufficient space to store all the addresses then enable |
| * unicast promiscuous mode |
| */ |
| if (__dev_uc_sync(netdev, igb_uc_sync, igb_uc_unsync)) { |
| rctl |= E1000_RCTL_UPE; |
| vmolr |= E1000_VMOLR_ROPE; |
| } |
| |
| /* enable VLAN filtering by default */ |
| rctl |= E1000_RCTL_VFE; |
| |
| /* disable VLAN filtering for modes that require it */ |
| if ((netdev->flags & IFF_PROMISC) || |
| (netdev->features & NETIF_F_RXALL)) { |
| /* if we fail to set all rules then just clear VFE */ |
| if (igb_vlan_promisc_enable(adapter)) |
| rctl &= ~E1000_RCTL_VFE; |
| } else { |
| igb_vlan_promisc_disable(adapter); |
| } |
| |
| /* update state of unicast, multicast, and VLAN filtering modes */ |
| rctl |= rd32(E1000_RCTL) & ~(E1000_RCTL_UPE | E1000_RCTL_MPE | |
| E1000_RCTL_VFE); |
| wr32(E1000_RCTL, rctl); |
| |
| #if (PAGE_SIZE < 8192) |
| if (!adapter->vfs_allocated_count) { |
| if (adapter->max_frame_size <= IGB_MAX_FRAME_BUILD_SKB) |
| rlpml = IGB_MAX_FRAME_BUILD_SKB; |
| } |
| #endif |
| wr32(E1000_RLPML, rlpml); |
| |
| /* In order to support SR-IOV and eventually VMDq it is necessary to set |
| * the VMOLR to enable the appropriate modes. Without this workaround |
| * we will have issues with VLAN tag stripping not being done for frames |
| * that are only arriving because we are the default pool |
| */ |
| if ((hw->mac.type < e1000_82576) || (hw->mac.type > e1000_i350)) |
| return; |
| |
| /* set UTA to appropriate mode */ |
| igb_set_uta(adapter, !!(vmolr & E1000_VMOLR_ROPE)); |
| |
| vmolr |= rd32(E1000_VMOLR(vfn)) & |
| ~(E1000_VMOLR_ROPE | E1000_VMOLR_MPME | E1000_VMOLR_ROMPE); |
| |
| /* enable Rx jumbo frames, restrict as needed to support build_skb */ |
| vmolr &= ~E1000_VMOLR_RLPML_MASK; |
| #if (PAGE_SIZE < 8192) |
| if (adapter->max_frame_size <= IGB_MAX_FRAME_BUILD_SKB) |
| vmolr |= IGB_MAX_FRAME_BUILD_SKB; |
| else |
| #endif |
| vmolr |= MAX_JUMBO_FRAME_SIZE; |
| vmolr |= E1000_VMOLR_LPE; |
| |
| wr32(E1000_VMOLR(vfn), vmolr); |
| |
| igb_restore_vf_multicasts(adapter); |
| } |
| |
| static void igb_check_wvbr(struct igb_adapter *adapter) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| u32 wvbr = 0; |
| |
| switch (hw->mac.type) { |
| case e1000_82576: |
| case e1000_i350: |
| wvbr = rd32(E1000_WVBR); |
| if (!wvbr) |
| return; |
| break; |
| default: |
| break; |
| } |
| |
| adapter->wvbr |= wvbr; |
| } |
| |
| #define IGB_STAGGERED_QUEUE_OFFSET 8 |
| |
| static void igb_spoof_check(struct igb_adapter *adapter) |
| { |
| int j; |
| |
| if (!adapter->wvbr) |
| return; |
| |
| for (j = 0; j < adapter->vfs_allocated_count; j++) { |
| if (adapter->wvbr & BIT(j) || |
| adapter->wvbr & BIT(j + IGB_STAGGERED_QUEUE_OFFSET)) { |
| dev_warn(&adapter->pdev->dev, |
| "Spoof event(s) detected on VF %d\n", j); |
| adapter->wvbr &= |
| ~(BIT(j) | |
| BIT(j + IGB_STAGGERED_QUEUE_OFFSET)); |
| } |
| } |
| } |
| |
| /* Need to wait a few seconds after link up to get diagnostic information from |
| * the phy |
| */ |
| static void igb_update_phy_info(struct timer_list *t) |
| { |
| struct igb_adapter *adapter = from_timer(adapter, t, phy_info_timer); |
| igb_get_phy_info(&adapter->hw); |
| } |
| |
| /** |
| * igb_has_link - check shared code for link and determine up/down |
| * @adapter: pointer to driver private info |
| **/ |
| bool igb_has_link(struct igb_adapter *adapter) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| bool link_active = false; |
| |
| /* get_link_status is set on LSC (link status) interrupt or |
| * rx sequence error interrupt. get_link_status will stay |
| * false until the e1000_check_for_link establishes link |
| * for copper adapters ONLY |
| */ |
| switch (hw->phy.media_type) { |
| case e1000_media_type_copper: |
| if (!hw->mac.get_link_status) |
| return true; |
| fallthrough; |
| case e1000_media_type_internal_serdes: |
| hw->mac.ops.check_for_link(hw); |
| link_active = !hw->mac.get_link_status; |
| break; |
| default: |
| case e1000_media_type_unknown: |
| break; |
| } |
| |
| if (((hw->mac.type == e1000_i210) || |
| (hw->mac.type == e1000_i211)) && |
| (hw->phy.id == I210_I_PHY_ID)) { |
| if (!netif_carrier_ok(adapter->netdev)) { |
| adapter->flags &= ~IGB_FLAG_NEED_LINK_UPDATE; |
| } else if (!(adapter->flags & IGB_FLAG_NEED_LINK_UPDATE)) { |
| adapter->flags |= IGB_FLAG_NEED_LINK_UPDATE; |
| adapter->link_check_timeout = jiffies; |
| } |
| } |
| |
| return link_active; |
| } |
| |
| static bool igb_thermal_sensor_event(struct e1000_hw *hw, u32 event) |
| { |
| bool ret = false; |
| u32 ctrl_ext, thstat; |
| |
| /* check for thermal sensor event on i350 copper only */ |
| if (hw->mac.type == e1000_i350) { |
| thstat = rd32(E1000_THSTAT); |
| ctrl_ext = rd32(E1000_CTRL_EXT); |
| |
| if ((hw->phy.media_type == e1000_media_type_copper) && |
| !(ctrl_ext & E1000_CTRL_EXT_LINK_MODE_SGMII)) |
| ret = !!(thstat & event); |
| } |
| |
| return ret; |
| } |
| |
| /** |
| * igb_check_lvmmc - check for malformed packets received |
| * and indicated in LVMMC register |
| * @adapter: pointer to adapter |
| **/ |
| static void igb_check_lvmmc(struct igb_adapter *adapter) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| u32 lvmmc; |
| |
| lvmmc = rd32(E1000_LVMMC); |
| if (lvmmc) { |
| if (unlikely(net_ratelimit())) { |
| netdev_warn(adapter->netdev, |
| "malformed Tx packet detected and dropped, LVMMC:0x%08x\n", |
| lvmmc); |
| } |
| } |
| } |
| |
| /** |
| * igb_watchdog - Timer Call-back |
| * @t: pointer to timer_list containing our private info pointer |
| **/ |
| static void igb_watchdog(struct timer_list *t) |
| { |
| struct igb_adapter *adapter = from_timer(adapter, t, watchdog_timer); |
| /* Do the rest outside of interrupt context */ |
| schedule_work(&adapter->watchdog_task); |
| } |
| |
| static void igb_watchdog_task(struct work_struct *work) |
| { |
| struct igb_adapter *adapter = container_of(work, |
| struct igb_adapter, |
| watchdog_task); |
| struct e1000_hw *hw = &adapter->hw; |
| struct e1000_phy_info *phy = &hw->phy; |
| struct net_device *netdev = adapter->netdev; |
| u32 link; |
| int i; |
| u32 connsw; |
| u16 phy_data, retry_count = 20; |
| |
| link = igb_has_link(adapter); |
| |
| if (adapter->flags & IGB_FLAG_NEED_LINK_UPDATE) { |
| if (time_after(jiffies, (adapter->link_check_timeout + HZ))) |
| adapter->flags &= ~IGB_FLAG_NEED_LINK_UPDATE; |
| else |
| link = false; |
| } |
| |
| /* Force link down if we have fiber to swap to */ |
| if (adapter->flags & IGB_FLAG_MAS_ENABLE) { |
| if (hw->phy.media_type == e1000_media_type_copper) { |
| connsw = rd32(E1000_CONNSW); |
| if (!(connsw & E1000_CONNSW_AUTOSENSE_EN)) |
| link = 0; |
| } |
| } |
| if (link) { |
| /* Perform a reset if the media type changed. */ |
| if (hw->dev_spec._82575.media_changed) { |
| hw->dev_spec._82575.media_changed = false; |
| adapter->flags |= IGB_FLAG_MEDIA_RESET; |
| igb_reset(adapter); |
| } |
| /* Cancel scheduled suspend requests. */ |
| pm_runtime_resume(netdev->dev.parent); |
| |
| if (!netif_carrier_ok(netdev)) { |
| u32 ctrl; |
| |
| hw->mac.ops.get_speed_and_duplex(hw, |
| &adapter->link_speed, |
| &adapter->link_duplex); |
| |
| ctrl = rd32(E1000_CTRL); |
| /* Links status message must follow this format */ |
| netdev_info(netdev, |
| "igb: %s NIC Link is Up %d Mbps %s Duplex, Flow Control: %s\n", |
| netdev->name, |
| adapter->link_speed, |
| adapter->link_duplex == FULL_DUPLEX ? |
| "Full" : "Half", |
| (ctrl & E1000_CTRL_TFCE) && |
| (ctrl & E1000_CTRL_RFCE) ? "RX/TX" : |
| (ctrl & E1000_CTRL_RFCE) ? "RX" : |
| (ctrl & E1000_CTRL_TFCE) ? "TX" : "None"); |
| |
| /* disable EEE if enabled */ |
| if ((adapter->flags & IGB_FLAG_EEE) && |
| (adapter->link_duplex == HALF_DUPLEX)) { |
| dev_info(&adapter->pdev->dev, |
| "EEE Disabled: unsupported at half duplex. Re-enable using ethtool when at full duplex.\n"); |
| adapter->hw.dev_spec._82575.eee_disable = true; |
| adapter->flags &= ~IGB_FLAG_EEE; |
| } |
| |
| /* check if SmartSpeed worked */ |
| igb_check_downshift(hw); |
| if (phy->speed_downgraded) |
| netdev_warn(netdev, "Link Speed was downgraded by SmartSpeed\n"); |
| |
| /* check for thermal sensor event */ |
| if (igb_thermal_sensor_event(hw, |
| E1000_THSTAT_LINK_THROTTLE)) |
| netdev_info(netdev, "The network adapter link speed was downshifted because it overheated\n"); |
| |
| /* adjust timeout factor according to speed/duplex */ |
| adapter->tx_timeout_factor = 1; |
| switch (adapter->link_speed) { |
| case SPEED_10: |
| adapter->tx_timeout_factor = 14; |
| break; |
| case SPEED_100: |
| /* maybe add some timeout factor ? */ |
| break; |
| } |
| |
| if (adapter->link_speed != SPEED_1000 || |
| !hw->phy.ops.read_reg) |
| goto no_wait; |
| |
| /* wait for Remote receiver status OK */ |
| retry_read_status: |
| if (!igb_read_phy_reg(hw, PHY_1000T_STATUS, |
| &phy_data)) { |
| if (!(phy_data & SR_1000T_REMOTE_RX_STATUS) && |
| retry_count) { |
| msleep(100); |
| retry_count--; |
| goto retry_read_status; |
| } else if (!retry_count) { |
| dev_err(&adapter->pdev->dev, "exceed max 2 second\n"); |
| } |
| } else { |
| dev_err(&adapter->pdev->dev, "read 1000Base-T Status Reg\n"); |
| } |
| no_wait: |
| netif_carrier_on(netdev); |
| |
| igb_ping_all_vfs(adapter); |
| igb_check_vf_rate_limit(adapter); |
| |
| /* link state has changed, schedule phy info update */ |
| if (!test_bit(__IGB_DOWN, &adapter->state)) |
| mod_timer(&adapter->phy_info_timer, |
| round_jiffies(jiffies + 2 * HZ)); |
| } |
| } else { |
| if (netif_carrier_ok(netdev)) { |
| adapter->link_speed = 0; |
| adapter->link_duplex = 0; |
| |
| /* check for thermal sensor event */ |
| if (igb_thermal_sensor_event(hw, |
| E1000_THSTAT_PWR_DOWN)) { |
| netdev_err(netdev, "The network adapter was stopped because it overheated\n"); |
| } |
| |
| /* Links status message must follow this format */ |
| netdev_info(netdev, "igb: %s NIC Link is Down\n", |
| netdev->name); |
| netif_carrier_off(netdev); |
| |
| igb_ping_all_vfs(adapter); |
| |
| /* link state has changed, schedule phy info update */ |
| if (!test_bit(__IGB_DOWN, &adapter->state)) |
| mod_timer(&adapter->phy_info_timer, |
| round_jiffies(jiffies + 2 * HZ)); |
| |
| /* link is down, time to check for alternate media */ |
| if (adapter->flags & IGB_FLAG_MAS_ENABLE) { |
| igb_check_swap_media(adapter); |
| if (adapter->flags & IGB_FLAG_MEDIA_RESET) { |
| schedule_work(&adapter->reset_task); |
| /* return immediately */ |
| return; |
| } |
| } |
| pm_schedule_suspend(netdev->dev.parent, |
| MSEC_PER_SEC * 5); |
| |
| /* also check for alternate media here */ |
| } else if (!netif_carrier_ok(netdev) && |
| (adapter->flags & IGB_FLAG_MAS_ENABLE)) { |
| igb_check_swap_media(adapter); |
| if (adapter->flags & IGB_FLAG_MEDIA_RESET) { |
| schedule_work(&adapter->reset_task); |
| /* return immediately */ |
| return; |
| } |
| } |
| } |
| |
| spin_lock(&adapter->stats64_lock); |
| igb_update_stats(adapter); |
| spin_unlock(&adapter->stats64_lock); |
| |
| for (i = 0; i < adapter->num_tx_queues; i++) { |
| struct igb_ring *tx_ring = adapter->tx_ring[i]; |
| if (!netif_carrier_ok(netdev)) { |
| /* We've lost link, so the controller stops DMA, |
| * but we've got queued Tx work that's never going |
| * to get done, so reset controller to flush Tx. |
| * (Do the reset outside of interrupt context). |
| */ |
| if (igb_desc_unused(tx_ring) + 1 < tx_ring->count) { |
| adapter->tx_timeout_count++; |
| schedule_work(&adapter->reset_task); |
| /* return immediately since reset is imminent */ |
| return; |
| } |
| } |
| |
| /* Force detection of hung controller every watchdog period */ |
| set_bit(IGB_RING_FLAG_TX_DETECT_HANG, &tx_ring->flags); |
| } |
| |
| /* Cause software interrupt to ensure Rx ring is cleaned */ |
| if (adapter->flags & IGB_FLAG_HAS_MSIX) { |
| u32 eics = 0; |
| |
| for (i = 0; i < adapter->num_q_vectors; i++) |
| eics |= adapter->q_vector[i]->eims_value; |
| wr32(E1000_EICS, eics); |
| } else { |
| wr32(E1000_ICS, E1000_ICS_RXDMT0); |
| } |
| |
| igb_spoof_check(adapter); |
| igb_ptp_rx_hang(adapter); |
| igb_ptp_tx_hang(adapter); |
| |
| /* Check LVMMC register on i350/i354 only */ |
| if ((adapter->hw.mac.type == e1000_i350) || |
| (adapter->hw.mac.type == e1000_i354)) |
| igb_check_lvmmc(adapter); |
| |
| /* Reset the timer */ |
| if (!test_bit(__IGB_DOWN, &adapter->state)) { |
| if (adapter->flags & IGB_FLAG_NEED_LINK_UPDATE) |
| mod_timer(&adapter->watchdog_timer, |
| round_jiffies(jiffies + HZ)); |
| else |
| mod_timer(&adapter->watchdog_timer, |
| round_jiffies(jiffies + 2 * HZ)); |
| } |
| } |
| |
| enum latency_range { |
| lowest_latency = 0, |
| low_latency = 1, |
| bulk_latency = 2, |
| latency_invalid = 255 |
| }; |
| |
| /** |
| * igb_update_ring_itr - update the dynamic ITR value based on packet size |
| * @q_vector: pointer to q_vector |
| * |
| * Stores a new ITR value based on strictly on packet size. This |
| * algorithm is less sophisticated than that used in igb_update_itr, |
| * due to the difficulty of synchronizing statistics across multiple |
| * receive rings. The divisors and thresholds used by this function |
| * were determined based on theoretical maximum wire speed and testing |
| * data, in order to minimize response time while increasing bulk |
| * throughput. |
| * This functionality is controlled by ethtool's coalescing settings. |
| * NOTE: This function is called only when operating in a multiqueue |
| * receive environment. |
| **/ |
| static void igb_update_ring_itr(struct igb_q_vector *q_vector) |
| { |
| int new_val = q_vector->itr_val; |
| int avg_wire_size = 0; |
| struct igb_adapter *adapter = q_vector->adapter; |
| unsigned int packets; |
| |
| /* For non-gigabit speeds, just fix the interrupt rate at 4000 |
| * ints/sec - ITR timer value of 120 ticks. |
| */ |
| if (adapter->link_speed != SPEED_1000) { |
| new_val = IGB_4K_ITR; |
| goto set_itr_val; |
| } |
| |
| packets = q_vector->rx.total_packets; |
| if (packets) |
| avg_wire_size = q_vector->rx.total_bytes / packets; |
| |
| packets = q_vector->tx.total_packets; |
| if (packets) |
| avg_wire_size = max_t(u32, avg_wire_size, |
| q_vector->tx.total_bytes / packets); |
| |
| /* if avg_wire_size isn't set no work was done */ |
| if (!avg_wire_size) |
| goto clear_counts; |
| |
| /* Add 24 bytes to size to account for CRC, preamble, and gap */ |
| avg_wire_size += 24; |
| |
| /* Don't starve jumbo frames */ |
| avg_wire_size = min(avg_wire_size, 3000); |
| |
| /* Give a little boost to mid-size frames */ |
| if ((avg_wire_size > 300) && (avg_wire_size < 1200)) |
| new_val = avg_wire_size / 3; |
| else |
| new_val = avg_wire_size / 2; |
| |
| /* conservative mode (itr 3) eliminates the lowest_latency setting */ |
| if (new_val < IGB_20K_ITR && |
| ((q_vector->rx.ring && adapter->rx_itr_setting == 3) || |
| (!q_vector->rx.ring && adapter->tx_itr_setting == 3))) |
| new_val = IGB_20K_ITR; |
| |
| set_itr_val: |
| if (new_val != q_vector->itr_val) { |
| q_vector->itr_val = new_val; |
| q_vector->set_itr = 1; |
| } |
| clear_counts: |
| q_vector->rx.total_bytes = 0; |
| q_vector->rx.total_packets = 0; |
| q_vector->tx.total_bytes = 0; |
| q_vector->tx.total_packets = 0; |
| } |
| |
| /** |
| * igb_update_itr - update the dynamic ITR value based on statistics |
| * @q_vector: pointer to q_vector |
| * @ring_container: ring info to update the itr for |
| * |
| * Stores a new ITR value based on packets and byte |
| * counts during the last interrupt. The advantage of per interrupt |
| * computation is faster updates and more accurate ITR for the current |
| * traffic pattern. Constants in this function were computed |
| * based on theoretical maximum wire speed and thresholds were set based |
| * on testing data as well as attempting to minimize response time |
| * while increasing bulk throughput. |
| * This functionality is controlled by ethtool's coalescing settings. |
| * NOTE: These calculations are only valid when operating in a single- |
| * queue environment. |
| **/ |
| static void igb_update_itr(struct igb_q_vector *q_vector, |
| struct igb_ring_container *ring_container) |
| { |
| unsigned int packets = ring_container->total_packets; |
| unsigned int bytes = ring_container->total_bytes; |
| u8 itrval = ring_container->itr; |
| |
| /* no packets, exit with status unchanged */ |
| if (packets == 0) |
| return; |
| |
| switch (itrval) { |
| case lowest_latency: |
| /* handle TSO and jumbo frames */ |
| if (bytes/packets > 8000) |
| itrval = bulk_latency; |
| else if ((packets < 5) && (bytes > 512)) |
| itrval = low_latency; |
| break; |
| case low_latency: /* 50 usec aka 20000 ints/s */ |
| if (bytes > 10000) { |
| /* this if handles the TSO accounting */ |
| if (bytes/packets > 8000) |
| itrval = bulk_latency; |
| else if ((packets < 10) || ((bytes/packets) > 1200)) |
| itrval = bulk_latency; |
| else if ((packets > 35)) |
| itrval = lowest_latency; |
| } else if (bytes/packets > 2000) { |
| itrval = bulk_latency; |
| } else if (packets <= 2 && bytes < 512) { |
| itrval = lowest_latency; |
| } |
| break; |
| case bulk_latency: /* 250 usec aka 4000 ints/s */ |
| if (bytes > 25000) { |
| if (packets > 35) |
| itrval = low_latency; |
| } else if (bytes < 1500) { |
| itrval = low_latency; |
| } |
| break; |
| } |
| |
| /* clear work counters since we have the values we need */ |
| ring_container->total_bytes = 0; |
| ring_container->total_packets = 0; |
| |
| /* write updated itr to ring container */ |
| ring_container->itr = itrval; |
| } |
| |
| static void igb_set_itr(struct igb_q_vector *q_vector) |
| { |
| struct igb_adapter *adapter = q_vector->adapter; |
| u32 new_itr = q_vector->itr_val; |
| u8 current_itr = 0; |
| |
| /* for non-gigabit speeds, just fix the interrupt rate at 4000 */ |
| if (adapter->link_speed != SPEED_1000) { |
| current_itr = 0; |
| new_itr = IGB_4K_ITR; |
| goto set_itr_now; |
| } |
| |
| igb_update_itr(q_vector, &q_vector->tx); |
| igb_update_itr(q_vector, &q_vector->rx); |
| |
| current_itr = max(q_vector->rx.itr, q_vector->tx.itr); |
| |
| /* conservative mode (itr 3) eliminates the lowest_latency setting */ |
| if (current_itr == lowest_latency && |
| ((q_vector->rx.ring && adapter->rx_itr_setting == 3) || |
| (!q_vector->rx.ring && adapter->tx_itr_setting == 3))) |
| current_itr = low_latency; |
| |
| switch (current_itr) { |
| /* counts and packets in update_itr are dependent on these numbers */ |
| case lowest_latency: |
| new_itr = IGB_70K_ITR; /* 70,000 ints/sec */ |
| break; |
| case low_latency: |
| new_itr = IGB_20K_ITR; /* 20,000 ints/sec */ |
| break; |
| case bulk_latency: |
| new_itr = IGB_4K_ITR; /* 4,000 ints/sec */ |
| break; |
| default: |
| break; |
| } |
| |
| set_itr_now: |
| if (new_itr != q_vector->itr_val) { |
| /* this attempts to bias the interrupt rate towards Bulk |
| * by adding intermediate steps when interrupt rate is |
| * increasing |
| */ |
| new_itr = new_itr > q_vector->itr_val ? |
| max((new_itr * q_vector->itr_val) / |
| (new_itr + (q_vector->itr_val >> 2)), |
| new_itr) : new_itr; |
| /* Don't write the value here; it resets the adapter's |
| * internal timer, and causes us to delay far longer than |
| * we should between interrupts. Instead, we write the ITR |
| * value at the beginning of the next interrupt so the timing |
| * ends up being correct. |
| */ |
| q_vector->itr_val = new_itr; |
| q_vector->set_itr = 1; |
| } |
| } |
| |
| static void igb_tx_ctxtdesc(struct igb_ring *tx_ring, |
| struct igb_tx_buffer *first, |
| u32 vlan_macip_lens, u32 type_tucmd, |
| u32 mss_l4len_idx) |
| { |
| struct e1000_adv_tx_context_desc *context_desc; |
| u16 i = tx_ring->next_to_use; |
| struct timespec64 ts; |
| |
| context_desc = IGB_TX_CTXTDESC(tx_ring, i); |
| |
| i++; |
| tx_ring->next_to_use = (i < tx_ring->count) ? i : 0; |
| |
| /* set bits to identify this as an advanced context descriptor */ |
| type_tucmd |= E1000_TXD_CMD_DEXT | E1000_ADVTXD_DTYP_CTXT; |
| |
| /* For 82575, context index must be unique per ring. */ |
| if (test_bit(IGB_RING_FLAG_TX_CTX_IDX, &tx_ring->flags)) |
| mss_l4len_idx |= tx_ring->reg_idx << 4; |
| |
| context_desc->vlan_macip_lens = cpu_to_le32(vlan_macip_lens); |
| context_desc->type_tucmd_mlhl = cpu_to_le32(type_tucmd); |
| context_desc->mss_l4len_idx = cpu_to_le32(mss_l4len_idx); |
| |
| /* We assume there is always a valid tx time available. Invalid times |
| * should have been handled by the upper layers. |
| */ |
| if (tx_ring->launchtime_enable) { |
| ts = ktime_to_timespec64(first->skb->tstamp); |
| skb_txtime_consumed(first->skb); |
| context_desc->seqnum_seed = cpu_to_le32(ts.tv_nsec / 32); |
| } else { |
| context_desc->seqnum_seed = 0; |
| } |
| } |
| |
| static int igb_tso(struct igb_ring *tx_ring, |
| struct igb_tx_buffer *first, |
| u8 *hdr_len) |
| { |
| u32 vlan_macip_lens, type_tucmd, mss_l4len_idx; |
| struct sk_buff *skb = first->skb; |
| union { |
| struct iphdr *v4; |
| struct ipv6hdr *v6; |
| unsigned char *hdr; |
| } ip; |
| union { |
| struct tcphdr *tcp; |
| struct udphdr *udp; |
| unsigned char *hdr; |
| } l4; |
| u32 paylen, l4_offset; |
| int err; |
| |
| if (skb->ip_summed != CHECKSUM_PARTIAL) |
| return 0; |
| |
| if (!skb_is_gso(skb)) |
| return 0; |
| |
| err = skb_cow_head(skb, 0); |
| if (err < 0) |
| return err; |
| |
| ip.hdr = skb_network_header(skb); |
| l4.hdr = skb_checksum_start(skb); |
| |
| /* ADV DTYP TUCMD MKRLOC/ISCSIHEDLEN */ |
| type_tucmd = (skb_shinfo(skb)->gso_type & SKB_GSO_UDP_L4) ? |
| E1000_ADVTXD_TUCMD_L4T_UDP : E1000_ADVTXD_TUCMD_L4T_TCP; |
| |
| /* initialize outer IP header fields */ |
| if (ip.v4->version == 4) { |
| unsigned char *csum_start = skb_checksum_start(skb); |
| unsigned char *trans_start = ip.hdr + (ip.v4->ihl * 4); |
| |
| /* IP header will have to cancel out any data that |
| * is not a part of the outer IP header |
| */ |
| ip.v4->check = csum_fold(csum_partial(trans_start, |
| csum_start - trans_start, |
| 0)); |
| type_tucmd |= E1000_ADVTXD_TUCMD_IPV4; |
| |
| ip.v4->tot_len = 0; |
| first->tx_flags |= IGB_TX_FLAGS_TSO | |
| IGB_TX_FLAGS_CSUM | |
| IGB_TX_FLAGS_IPV4; |
| } else { |
| ip.v6->payload_len = 0; |
| first->tx_flags |= IGB_TX_FLAGS_TSO | |
| IGB_TX_FLAGS_CSUM; |
| } |
| |
| /* determine offset of inner transport header */ |
| l4_offset = l4.hdr - skb->data; |
| |
| /* remove payload length from inner checksum */ |
| paylen = skb->len - l4_offset; |
| if (type_tucmd & E1000_ADVTXD_TUCMD_L4T_TCP) { |
| /* compute length of segmentation header */ |
| *hdr_len = (l4.tcp->doff * 4) + l4_offset; |
| csum_replace_by_diff(&l4.tcp->check, |
| (__force __wsum)htonl(paylen)); |
| } else { |
| /* compute length of segmentation header */ |
| *hdr_len = sizeof(*l4.udp) + l4_offset; |
| csum_replace_by_diff(&l4.udp->check, |
| (__force __wsum)htonl(paylen)); |
| } |
| |
| /* update gso size and bytecount with header size */ |
| first->gso_segs = skb_shinfo(skb)->gso_segs; |
| first->bytecount += (first->gso_segs - 1) * *hdr_len; |
| |
| /* MSS L4LEN IDX */ |
| mss_l4len_idx = (*hdr_len - l4_offset) << E1000_ADVTXD_L4LEN_SHIFT; |
| mss_l4len_idx |= skb_shinfo(skb)->gso_size << E1000_ADVTXD_MSS_SHIFT; |
| |
| /* VLAN MACLEN IPLEN */ |
| vlan_macip_lens = l4.hdr - ip.hdr; |
| vlan_macip_lens |= (ip.hdr - skb->data) << E1000_ADVTXD_MACLEN_SHIFT; |
| vlan_macip_lens |= first->tx_flags & IGB_TX_FLAGS_VLAN_MASK; |
| |
| igb_tx_ctxtdesc(tx_ring, first, vlan_macip_lens, |
| type_tucmd, mss_l4len_idx); |
| |
| return 1; |
| } |
| |
| static void igb_tx_csum(struct igb_ring *tx_ring, struct igb_tx_buffer *first) |
| { |
| struct sk_buff *skb = first->skb; |
| u32 vlan_macip_lens = 0; |
| u32 type_tucmd = 0; |
| |
| if (skb->ip_summed != CHECKSUM_PARTIAL) { |
| csum_failed: |
| if (!(first->tx_flags & IGB_TX_FLAGS_VLAN) && |
| !tx_ring->launchtime_enable) |
| return; |
| goto no_csum; |
| } |
| |
| switch (skb->csum_offset) { |
| case offsetof(struct tcphdr, check): |
| type_tucmd = E1000_ADVTXD_TUCMD_L4T_TCP; |
| fallthrough; |
| case offsetof(struct udphdr, check): |
| break; |
| case offsetof(struct sctphdr, checksum): |
| /* validate that this is actually an SCTP request */ |
| if (skb_csum_is_sctp(skb)) { |
| type_tucmd = E1000_ADVTXD_TUCMD_L4T_SCTP; |
| break; |
| } |
| fallthrough; |
| default: |
| skb_checksum_help(skb); |
| goto csum_failed; |
| } |
| |
| /* update TX checksum flag */ |
| first->tx_flags |= IGB_TX_FLAGS_CSUM; |
| vlan_macip_lens = skb_checksum_start_offset(skb) - |
| skb_network_offset(skb); |
| no_csum: |
| vlan_macip_lens |= skb_network_offset(skb) << E1000_ADVTXD_MACLEN_SHIFT; |
| vlan_macip_lens |= first->tx_flags & IGB_TX_FLAGS_VLAN_MASK; |
| |
| igb_tx_ctxtdesc(tx_ring, first, vlan_macip_lens, type_tucmd, 0); |
| } |
| |
| #define IGB_SET_FLAG(_input, _flag, _result) \ |
| ((_flag <= _result) ? \ |
| ((u32)(_input & _flag) * (_result / _flag)) : \ |
| ((u32)(_input & _flag) / (_flag / _result))) |
| |
| static u32 igb_tx_cmd_type(struct sk_buff *skb, u32 tx_flags) |
| { |
| /* set type for advanced descriptor with frame checksum insertion */ |
| u32 cmd_type = E1000_ADVTXD_DTYP_DATA | |
| E1000_ADVTXD_DCMD_DEXT | |
| E1000_ADVTXD_DCMD_IFCS; |
| |
| /* set HW vlan bit if vlan is present */ |
| cmd_type |= IGB_SET_FLAG(tx_flags, IGB_TX_FLAGS_VLAN, |
| (E1000_ADVTXD_DCMD_VLE)); |
| |
| /* set segmentation bits for TSO */ |
| cmd_type |= IGB_SET_FLAG(tx_flags, IGB_TX_FLAGS_TSO, |
| (E1000_ADVTXD_DCMD_TSE)); |
| |
| /* set timestamp bit if present */ |
| cmd_type |= IGB_SET_FLAG(tx_flags, IGB_TX_FLAGS_TSTAMP, |
| (E1000_ADVTXD_MAC_TSTAMP)); |
| |
| /* insert frame checksum */ |
| cmd_type ^= IGB_SET_FLAG(skb->no_fcs, 1, E1000_ADVTXD_DCMD_IFCS); |
| |
| return cmd_type; |
| } |
| |
| static void igb_tx_olinfo_status(struct igb_ring *tx_ring, |
| union e1000_adv_tx_desc *tx_desc, |
| u32 tx_flags, unsigned int paylen) |
| { |
| u32 olinfo_status = paylen << E1000_ADVTXD_PAYLEN_SHIFT; |
| |
| /* 82575 requires a unique index per ring */ |
| if (test_bit(IGB_RING_FLAG_TX_CTX_IDX, &tx_ring->flags)) |
| olinfo_status |= tx_ring->reg_idx << 4; |
| |
| /* insert L4 checksum */ |
| olinfo_status |= IGB_SET_FLAG(tx_flags, |
| IGB_TX_FLAGS_CSUM, |
| (E1000_TXD_POPTS_TXSM << 8)); |
| |
| /* insert IPv4 checksum */ |
| olinfo_status |= IGB_SET_FLAG(tx_flags, |
| IGB_TX_FLAGS_IPV4, |
| (E1000_TXD_POPTS_IXSM << 8)); |
| |
| tx_desc->read.olinfo_status = cpu_to_le32(olinfo_status); |
| } |
| |
| static int __igb_maybe_stop_tx(struct igb_ring *tx_ring, const u16 size) |
| { |
| struct net_device *netdev = tx_ring->netdev; |
| |
| netif_stop_subqueue(netdev, tx_ring->queue_index); |
| |
| /* Herbert's original patch had: |
| * smp_mb__after_netif_stop_queue(); |
| * but since that doesn't exist yet, just open code it. |
| */ |
| smp_mb(); |
| |
| /* We need to check again in a case another CPU has just |
| * made room available. |
| */ |
| if (igb_desc_unused(tx_ring) < size) |
| return -EBUSY; |
| |
| /* A reprieve! */ |
| netif_wake_subqueue(netdev, tx_ring->queue_index); |
| |
| u64_stats_update_begin(&tx_ring->tx_syncp2); |
| tx_ring->tx_stats.restart_queue2++; |
| u64_stats_update_end(&tx_ring->tx_syncp2); |
| |
| return 0; |
| } |
| |
| static inline int igb_maybe_stop_tx(struct igb_ring *tx_ring, const u16 size) |
| { |
| if (igb_desc_unused(tx_ring) >= size) |
| return 0; |
| return __igb_maybe_stop_tx(tx_ring, size); |
| } |
| |
| static int igb_tx_map(struct igb_ring *tx_ring, |
| struct igb_tx_buffer *first, |
| const u8 hdr_len) |
| { |
| struct sk_buff *skb = first->skb; |
| struct igb_tx_buffer *tx_buffer; |
| union e1000_adv_tx_desc *tx_desc; |
| skb_frag_t *frag; |
| dma_addr_t dma; |
| unsigned int data_len, size; |
| u32 tx_flags = first->tx_flags; |
| u32 cmd_type = igb_tx_cmd_type(skb, tx_flags); |
| u16 i = tx_ring->next_to_use; |
| |
| tx_desc = IGB_TX_DESC(tx_ring, i); |
| |
| igb_tx_olinfo_status(tx_ring, tx_desc, tx_flags, skb->len - hdr_len); |
| |
| size = skb_headlen(skb); |
| data_len = skb->data_len; |
| |
| dma = dma_map_single(tx_ring->dev, skb->data, size, DMA_TO_DEVICE); |
| |
| tx_buffer = first; |
| |
| for (frag = &skb_shinfo(skb)->frags[0];; frag++) { |
| if (dma_mapping_error(tx_ring->dev, dma)) |
| goto dma_error; |
| |
| /* record length, and DMA address */ |
| dma_unmap_len_set(tx_buffer, len, size); |
| dma_unmap_addr_set(tx_buffer, dma, dma); |
| |
| tx_desc->read.buffer_addr = cpu_to_le64(dma); |
| |
| while (unlikely(size > IGB_MAX_DATA_PER_TXD)) { |
| tx_desc->read.cmd_type_len = |
| cpu_to_le32(cmd_type ^ IGB_MAX_DATA_PER_TXD); |
| |
| i++; |
| tx_desc++; |
| if (i == tx_ring->count) { |
| tx_desc = IGB_TX_DESC(tx_ring, 0); |
| i = 0; |
| } |
| tx_desc->read.olinfo_status = 0; |
| |
| dma += IGB_MAX_DATA_PER_TXD; |
| size -= IGB_MAX_DATA_PER_TXD; |
| |
| tx_desc->read.buffer_addr = cpu_to_le64(dma); |
| } |
| |
| if (likely(!data_len)) |
| break; |
| |
| tx_desc->read.cmd_type_len = cpu_to_le32(cmd_type ^ size); |
| |
| i++; |
| tx_desc++; |
| if (i == tx_ring->count) { |
| tx_desc = IGB_TX_DESC(tx_ring, 0); |
| i = 0; |
| } |
| tx_desc->read.olinfo_status = 0; |
| |
| size = skb_frag_size(frag); |
| data_len -= size; |
| |
| dma = skb_frag_dma_map(tx_ring->dev, frag, 0, |
| size, DMA_TO_DEVICE); |
| |
| tx_buffer = &tx_ring->tx_buffer_info[i]; |
| } |
| |
| /* write last descriptor with RS and EOP bits */ |
| cmd_type |= size | IGB_TXD_DCMD; |
| tx_desc->read.cmd_type_len = cpu_to_le32(cmd_type); |
| |
| netdev_tx_sent_queue(txring_txq(tx_ring), first->bytecount); |
| |
| /* set the timestamp */ |
| first->time_stamp = jiffies; |
| |
| skb_tx_timestamp(skb); |
| |
| /* Force memory writes to complete before letting h/w know there |
| * are new descriptors to fetch. (Only applicable for weak-ordered |
| * memory model archs, such as IA-64). |
| * |
| * We also need this memory barrier to make certain all of the |
| * status bits have been updated before next_to_watch is written. |
| */ |
| dma_wmb(); |
| |
| /* set next_to_watch value indicating a packet is present */ |
| first->next_to_watch = tx_desc; |
| |
| i++; |
| if (i == tx_ring->count) |
| i = 0; |
| |
| tx_ring->next_to_use = i; |
| |
| /* Make sure there is space in the ring for the next send. */ |
| igb_maybe_stop_tx(tx_ring, DESC_NEEDED); |
| |
| if (netif_xmit_stopped(txring_txq(tx_ring)) || !netdev_xmit_more()) { |
| writel(i, tx_ring->tail); |
| } |
| return 0; |
| |
| dma_error: |
| dev_err(tx_ring->dev, "TX DMA map failed\n"); |
| tx_buffer = &tx_ring->tx_buffer_info[i]; |
| |
| /* clear dma mappings for failed tx_buffer_info map */ |
| while (tx_buffer != first) { |
| if (dma_unmap_len(tx_buffer, len)) |
| dma_unmap_page(tx_ring->dev, |
| dma_unmap_addr(tx_buffer, dma), |
| dma_unmap_len(tx_buffer, len), |
| DMA_TO_DEVICE); |
| dma_unmap_len_set(tx_buffer, len, 0); |
| |
| if (i-- == 0) |
| i += tx_ring->count; |
| tx_buffer = &tx_ring->tx_buffer_info[i]; |
| } |
| |
| if (dma_unmap_len(tx_buffer, len)) |
| dma_unmap_single(tx_ring->dev, |
| dma_unmap_addr(tx_buffer, dma), |
| dma_unmap_len(tx_buffer, len), |
| DMA_TO_DEVICE); |
| dma_unmap_len_set(tx_buffer, len, 0); |
| |
| dev_kfree_skb_any(tx_buffer->skb); |
| tx_buffer->skb = NULL; |
| |
| tx_ring->next_to_use = i; |
| |
| return -1; |
| } |
| |
| int igb_xmit_xdp_ring(struct igb_adapter *adapter, |
| struct igb_ring *tx_ring, |
| struct xdp_frame *xdpf) |
| { |
| struct skb_shared_info *sinfo = xdp_get_shared_info_from_frame(xdpf); |
| u8 nr_frags = unlikely(xdp_frame_has_frags(xdpf)) ? sinfo->nr_frags : 0; |
| u16 count, i, index = tx_ring->next_to_use; |
| struct igb_tx_buffer *tx_head = &tx_ring->tx_buffer_info[index]; |
| struct igb_tx_buffer *tx_buffer = tx_head; |
| union e1000_adv_tx_desc *tx_desc = IGB_TX_DESC(tx_ring, index); |
| u32 len = xdpf->len, cmd_type, olinfo_status; |
| void *data = xdpf->data; |
| |
| count = TXD_USE_COUNT(len); |
| for (i = 0; i < nr_frags; i++) |
| count += TXD_USE_COUNT(skb_frag_size(&sinfo->frags[i])); |
| |
| if (igb_maybe_stop_tx(tx_ring, count + 3)) |
| return IGB_XDP_CONSUMED; |
| |
| i = 0; |
| /* record the location of the first descriptor for this packet */ |
| tx_head->bytecount = xdp_get_frame_len(xdpf); |
| tx_head->type = IGB_TYPE_XDP; |
| tx_head->gso_segs = 1; |
| tx_head->xdpf = xdpf; |
| |
| olinfo_status = tx_head->bytecount << E1000_ADVTXD_PAYLEN_SHIFT; |
| /* 82575 requires a unique index per ring */ |
| if (test_bit(IGB_RING_FLAG_TX_CTX_IDX, &tx_ring->flags)) |
| olinfo_status |= tx_ring->reg_idx << 4; |
| tx_desc->read.olinfo_status = cpu_to_le32(olinfo_status); |
| |
| for (;;) { |
| dma_addr_t dma; |
| |
| dma = dma_map_single(tx_ring->dev, data, len, DMA_TO_DEVICE); |
| if (dma_mapping_error(tx_ring->dev, dma)) |
| goto unmap; |
| |
| /* record length, and DMA address */ |
| dma_unmap_len_set(tx_buffer, len, len); |
| dma_unmap_addr_set(tx_buffer, dma, dma); |
| |
| /* put descriptor type bits */ |
| cmd_type = E1000_ADVTXD_DTYP_DATA | E1000_ADVTXD_DCMD_DEXT | |
| E1000_ADVTXD_DCMD_IFCS | len; |
| |
| tx_desc->read.cmd_type_len = cpu_to_le32(cmd_type); |
| tx_desc->read.buffer_addr = cpu_to_le64(dma); |
| |
| tx_buffer->protocol = 0; |
| |
| if (++index == tx_ring->count) |
| index = 0; |
| |
| if (i == nr_frags) |
| break; |
| |
| tx_buffer = &tx_ring->tx_buffer_info[index]; |
| tx_desc = IGB_TX_DESC(tx_ring, index); |
| tx_desc->read.olinfo_status = 0; |
| |
| data = skb_frag_address(&sinfo->frags[i]); |
| len = skb_frag_size(&sinfo->frags[i]); |
| i++; |
| } |
| tx_desc->read.cmd_type_len |= cpu_to_le32(IGB_TXD_DCMD); |
| |
| netdev_tx_sent_queue(txring_txq(tx_ring), tx_head->bytecount); |
| /* set the timestamp */ |
| tx_head->time_stamp = jiffies; |
| |
| /* Avoid any potential race with xdp_xmit and cleanup */ |
| smp_wmb(); |
| |
| /* set next_to_watch value indicating a packet is present */ |
| tx_head->next_to_watch = tx_desc; |
| tx_ring->next_to_use = index; |
| |
| /* Make sure there is space in the ring for the next send. */ |
| igb_maybe_stop_tx(tx_ring, DESC_NEEDED); |
| |
| if (netif_xmit_stopped(txring_txq(tx_ring)) || !netdev_xmit_more()) |
| writel(index, tx_ring->tail); |
| |
| return IGB_XDP_TX; |
| |
| unmap: |
| for (;;) { |
| tx_buffer = &tx_ring->tx_buffer_info[index]; |
| if (dma_unmap_len(tx_buffer, len)) |
| dma_unmap_page(tx_ring->dev, |
| dma_unmap_addr(tx_buffer, dma), |
| dma_unmap_len(tx_buffer, len), |
| DMA_TO_DEVICE); |
| dma_unmap_len_set(tx_buffer, len, 0); |
| if (tx_buffer == tx_head) |
| break; |
| |
| if (!index) |
| index += tx_ring->count; |
| index--; |
| } |
| |
| return IGB_XDP_CONSUMED; |
| } |
| |
| netdev_tx_t igb_xmit_frame_ring(struct sk_buff *skb, |
| struct igb_ring *tx_ring) |
| { |
| struct igb_tx_buffer *first; |
| int tso; |
| u32 tx_flags = 0; |
| unsigned short f; |
| u16 count = TXD_USE_COUNT(skb_headlen(skb)); |
| __be16 protocol = vlan_get_protocol(skb); |
| u8 hdr_len = 0; |
| |
| /* need: 1 descriptor per page * PAGE_SIZE/IGB_MAX_DATA_PER_TXD, |
| * + 1 desc for skb_headlen/IGB_MAX_DATA_PER_TXD, |
| * + 2 desc gap to keep tail from touching head, |
| * + 1 desc for context descriptor, |
| * otherwise try next time |
| */ |
| for (f = 0; f < skb_shinfo(skb)->nr_frags; f++) |
| count += TXD_USE_COUNT(skb_frag_size( |
| &skb_shinfo(skb)->frags[f])); |
| |
| if (igb_maybe_stop_tx(tx_ring, count + 3)) { |
| /* this is a hard error */ |
| return NETDEV_TX_BUSY; |
| } |
| |
| /* record the location of the first descriptor for this packet */ |
| first = &tx_ring->tx_buffer_info[tx_ring->next_to_use]; |
| first->type = IGB_TYPE_SKB; |
| first->skb = skb; |
| first->bytecount = skb->len; |
| first->gso_segs = 1; |
| |
| if (unlikely(skb_shinfo(skb)->tx_flags & SKBTX_HW_TSTAMP)) { |
| struct igb_adapter *adapter = netdev_priv(tx_ring->netdev); |
| |
| if (adapter->tstamp_config.tx_type == HWTSTAMP_TX_ON && |
| !test_and_set_bit_lock(__IGB_PTP_TX_IN_PROGRESS, |
| &adapter->state)) { |
| skb_shinfo(skb)->tx_flags |= SKBTX_IN_PROGRESS; |
| tx_flags |= IGB_TX_FLAGS_TSTAMP; |
| |
| adapter->ptp_tx_skb = skb_get(skb); |
| adapter->ptp_tx_start = jiffies; |
| if (adapter->hw.mac.type == e1000_82576) |
| schedule_work(&adapter->ptp_tx_work); |
| } else { |
| adapter->tx_hwtstamp_skipped++; |
| } |
| } |
| |
| if (skb_vlan_tag_present(skb)) { |
| tx_flags |= IGB_TX_FLAGS_VLAN; |
| tx_flags |= (skb_vlan_tag_get(skb) << IGB_TX_FLAGS_VLAN_SHIFT); |
| } |
| |
| /* record initial flags and protocol */ |
| first->tx_flags = tx_flags; |
| first->protocol = protocol; |
| |
| tso = igb_tso(tx_ring, first, &hdr_len); |
| if (tso < 0) |
| goto out_drop; |
| else if (!tso) |
| igb_tx_csum(tx_ring, first); |
| |
| if (igb_tx_map(tx_ring, first, hdr_len)) |
| goto cleanup_tx_tstamp; |
| |
| return NETDEV_TX_OK; |
| |
| out_drop: |
| dev_kfree_skb_any(first->skb); |
| first->skb = NULL; |
| cleanup_tx_tstamp: |
| if (unlikely(tx_flags & IGB_TX_FLAGS_TSTAMP)) { |
| struct igb_adapter *adapter = netdev_priv(tx_ring->netdev); |
| |
| dev_kfree_skb_any(adapter->ptp_tx_skb); |
| adapter->ptp_tx_skb = NULL; |
| if (adapter->hw.mac.type == e1000_82576) |
| cancel_work_sync(&adapter->ptp_tx_work); |
| clear_bit_unlock(__IGB_PTP_TX_IN_PROGRESS, &adapter->state); |
| } |
| |
| return NETDEV_TX_OK; |
| } |
| |
| static inline struct igb_ring *igb_tx_queue_mapping(struct igb_adapter *adapter, |
| struct sk_buff *skb) |
| { |
| unsigned int r_idx = skb->queue_mapping; |
| |
| if (r_idx >= adapter->num_tx_queues) |
| r_idx = r_idx % adapter->num_tx_queues; |
| |
| return adapter->tx_ring[r_idx]; |
| } |
| |
| static netdev_tx_t igb_xmit_frame(struct sk_buff *skb, |
| struct net_device *netdev) |
| { |
| struct igb_adapter *adapter = netdev_priv(netdev); |
| |
| /* The minimum packet size with TCTL.PSP set is 17 so pad the skb |
| * in order to meet this minimum size requirement. |
| */ |
| if (skb_put_padto(skb, 17)) |
| return NETDEV_TX_OK; |
| |
| return igb_xmit_frame_ring(skb, igb_tx_queue_mapping(adapter, skb)); |
| } |
| |
| /** |
| * igb_tx_timeout - Respond to a Tx Hang |
| * @netdev: network interface device structure |
| * @txqueue: number of the Tx queue that hung (unused) |
| **/ |
| static void igb_tx_timeout(struct net_device *netdev, unsigned int __always_unused txqueue) |
| { |
| struct igb_adapter *adapter = netdev_priv(netdev); |
| struct e1000_hw *hw = &adapter->hw; |
| |
| /* Do the reset outside of interrupt context */ |
| adapter->tx_timeout_count++; |
| |
| if (hw->mac.type >= e1000_82580) |
| hw->dev_spec._82575.global_device_reset = true; |
| |
| schedule_work(&adapter->reset_task); |
| wr32(E1000_EICS, |
| (adapter->eims_enable_mask & ~adapter->eims_other)); |
| } |
| |
| static void igb_reset_task(struct work_struct *work) |
| { |
| struct igb_adapter *adapter; |
| adapter = container_of(work, struct igb_adapter, reset_task); |
| |
| rtnl_lock(); |
| /* If we're already down or resetting, just bail */ |
| if (test_bit(__IGB_DOWN, &adapter->state) || |
| test_bit(__IGB_RESETTING, &adapter->state)) { |
| rtnl_unlock(); |
| return; |
| } |
| |
| igb_dump(adapter); |
| netdev_err(adapter->netdev, "Reset adapter\n"); |
| igb_reinit_locked(adapter); |
| rtnl_unlock(); |
| } |
| |
| /** |
| * igb_get_stats64 - Get System Network Statistics |
| * @netdev: network interface device structure |
| * @stats: rtnl_link_stats64 pointer |
| **/ |
| static void igb_get_stats64(struct net_device *netdev, |
| struct rtnl_link_stats64 *stats) |
| { |
| struct igb_adapter *adapter = netdev_priv(netdev); |
| |
| spin_lock(&adapter->stats64_lock); |
| igb_update_stats(adapter); |
| memcpy(stats, &adapter->stats64, sizeof(*stats)); |
| spin_unlock(&adapter->stats64_lock); |
| } |
| |
| /** |
| * igb_change_mtu - Change the Maximum Transfer Unit |
| * @netdev: network interface device structure |
| * @new_mtu: new value for maximum frame size |
| * |
| * Returns 0 on success, negative on failure |
| **/ |
| static int igb_change_mtu(struct net_device *netdev, int new_mtu) |
| { |
| struct igb_adapter *adapter = netdev_priv(netdev); |
| int max_frame = new_mtu + IGB_ETH_PKT_HDR_PAD; |
| |
| if (adapter->xdp_prog) { |
| int i; |
| |
| for (i = 0; i < adapter->num_rx_queues; i++) { |
| struct igb_ring *ring = adapter->rx_ring[i]; |
| |
| if (max_frame > igb_rx_bufsz(ring)) { |
| netdev_warn(adapter->netdev, |
| "Requested MTU size is not supported with XDP. Max frame size is %d\n", |
| max_frame); |
| return -EINVAL; |
| } |
| } |
| } |
| |
| /* adjust max frame to be at least the size of a standard frame */ |
| if (max_frame < (ETH_FRAME_LEN + ETH_FCS_LEN)) |
| max_frame = ETH_FRAME_LEN + ETH_FCS_LEN; |
| |
| while (test_and_set_bit(__IGB_RESETTING, &adapter->state)) |
| usleep_range(1000, 2000); |
| |
| /* igb_down has a dependency on max_frame_size */ |
| adapter->max_frame_size = max_frame; |
| |
| if (netif_running(netdev)) |
| igb_down(adapter); |
| |
| netdev_dbg(netdev, "changing MTU from %d to %d\n", |
| netdev->mtu, new_mtu); |
| WRITE_ONCE(netdev->mtu, new_mtu); |
| |
| if (netif_running(netdev)) |
| igb_up(adapter); |
| else |
| igb_reset(adapter); |
| |
| clear_bit(__IGB_RESETTING, &adapter->state); |
| |
| return 0; |
| } |
| |
| /** |
| * igb_update_stats - Update the board statistics counters |
| * @adapter: board private structure |
| **/ |
| void igb_update_stats(struct igb_adapter *adapter) |
| { |
| struct rtnl_link_stats64 *net_stats = &adapter->stats64; |
| struct e1000_hw *hw = &adapter->hw; |
| struct pci_dev *pdev = adapter->pdev; |
| u32 reg, mpc; |
| int i; |
| u64 bytes, packets; |
| unsigned int start; |
| u64 _bytes, _packets; |
| |
| /* Prevent stats update while adapter is being reset, or if the pci |
| * connection is down. |
| */ |
| if (adapter->link_speed == 0) |
| return; |
| if (pci_channel_offline(pdev)) |
| return; |
| |
| bytes = 0; |
| packets = 0; |
| |
| rcu_read_lock(); |
| for (i = 0; i < adapter->num_rx_queues; i++) { |
| struct igb_ring *ring = adapter->rx_ring[i]; |
| u32 rqdpc = rd32(E1000_RQDPC(i)); |
| if (hw->mac.type >= e1000_i210) |
| wr32(E1000_RQDPC(i), 0); |
| |
| if (rqdpc) { |
| ring->rx_stats.drops += rqdpc; |
| net_stats->rx_fifo_errors += rqdpc; |
| } |
| |
| do { |
| start = u64_stats_fetch_begin(&ring->rx_syncp); |
| _bytes = ring->rx_stats.bytes; |
| _packets = ring->rx_stats.packets; |
| } while (u64_stats_fetch_retry(&ring->rx_syncp, start)); |
| bytes += _bytes; |
| packets += _packets; |
| } |
| |
| net_stats->rx_bytes = bytes; |
| net_stats->rx_packets = packets; |
| |
| bytes = 0; |
| packets = 0; |
| for (i = 0; i < adapter->num_tx_queues; i++) { |
| struct igb_ring *ring = adapter->tx_ring[i]; |
| do { |
| start = u64_stats_fetch_begin(&ring->tx_syncp); |
| _bytes = ring->tx_stats.bytes; |
| _packets = ring->tx_stats.packets; |
| } while (u64_stats_fetch_retry(&ring->tx_syncp, start)); |
| bytes += _bytes; |
| packets += _packets; |
| } |
| net_stats->tx_bytes = bytes; |
| net_stats->tx_packets = packets; |
| rcu_read_unlock(); |
| |
| /* read stats registers */ |
| adapter->stats.crcerrs += rd32(E1000_CRCERRS); |
| adapter->stats.gprc += rd32(E1000_GPRC); |
| adapter->stats.gorc += rd32(E1000_GORCL); |
| rd32(E1000_GORCH); /* clear GORCL */ |
| adapter->stats.bprc += rd32(E1000_BPRC); |
| adapter->stats.mprc += rd32(E1000_MPRC); |
| adapter->stats.roc += rd32(E1000_ROC); |
| |
| adapter->stats.prc64 += rd32(E1000_PRC64); |
| adapter->stats.prc127 += rd32(E1000_PRC127); |
| adapter->stats.prc255 += rd32(E1000_PRC255); |
| adapter->stats.prc511 += rd32(E1000_PRC511); |
| adapter->stats.prc1023 += rd32(E1000_PRC1023); |
| adapter->stats.prc1522 += rd32(E1000_PRC1522); |
| adapter->stats.symerrs += rd32(E1000_SYMERRS); |
| adapter->stats.sec += rd32(E1000_SEC); |
| |
| mpc = rd32(E1000_MPC); |
| adapter->stats.mpc += mpc; |
| net_stats->rx_fifo_errors += mpc; |
| adapter->stats.scc += rd32(E1000_SCC); |
| adapter->stats.ecol += rd32(E1000_ECOL); |
| adapter->stats.mcc += rd32(E1000_MCC); |
| adapter->stats.latecol += rd32(E1000_LATECOL); |
| adapter->stats.dc += rd32(E1000_DC); |
| adapter->stats.rlec += rd32(E1000_RLEC); |
| adapter->stats.xonrxc += rd32(E1000_XONRXC); |
| adapter->stats.xontxc += rd32(E1000_XONTXC); |
| adapter->stats.xoffrxc += rd32(E1000_XOFFRXC); |
| adapter->stats.xofftxc += rd32(E1000_XOFFTXC); |
| adapter->stats.fcruc += rd32(E1000_FCRUC); |
| adapter->stats.gptc += rd32(E1000_GPTC); |
| adapter->stats.gotc += rd32(E1000_GOTCL); |
| rd32(E1000_GOTCH); /* clear GOTCL */ |
| adapter->stats.rnbc += rd32(E1000_RNBC); |
| adapter->stats.ruc += rd32(E1000_RUC); |
| adapter->stats.rfc += rd32(E1000_RFC); |
| adapter->stats.rjc += rd32(E1000_RJC); |
| adapter->stats.tor += rd32(E1000_TORH); |
| adapter->stats.tot += rd32(E1000_TOTH); |
| adapter->stats.tpr += rd32(E1000_TPR); |
| |
| adapter->stats.ptc64 += rd32(E1000_PTC64); |
| adapter->stats.ptc127 += rd32(E1000_PTC127); |
| adapter->stats.ptc255 += rd32(E1000_PTC255); |
| adapter->stats.ptc511 += rd32(E1000_PTC511); |
| adapter->stats.ptc1023 += rd32(E1000_PTC1023); |
| adapter->stats.ptc1522 += rd32(E1000_PTC1522); |
| |
| adapter->stats.mptc += rd32(E1000_MPTC); |
| adapter->stats.bptc += rd32(E1000_BPTC); |
| |
| adapter->stats.tpt += rd32(E1000_TPT); |
| adapter->stats.colc += rd32(E1000_COLC); |
| |
| adapter->stats.algnerrc += rd32(E1000_ALGNERRC); |
| /* read internal phy specific stats */ |
| reg = rd32(E1000_CTRL_EXT); |
| if (!(reg & E1000_CTRL_EXT_LINK_MODE_MASK)) { |
| adapter->stats.rxerrc += rd32(E1000_RXERRC); |
| |
| /* this stat has invalid values on i210/i211 */ |
| if ((hw->mac.type != e1000_i210) && |
| (hw->mac.type != e1000_i211)) |
| adapter->stats.tncrs += rd32(E1000_TNCRS); |
| } |
| |
| adapter->stats.tsctc += rd32(E1000_TSCTC); |
| adapter->stats.tsctfc += rd32(E1000_TSCTFC); |
| |
| adapter->stats.iac += rd32(E1000_IAC); |
| adapter->stats.icrxoc += rd32(E1000_ICRXOC); |
| adapter->stats.icrxptc += rd32(E1000_ICRXPTC); |
| adapter->stats.icrxatc += rd32(E1000_ICRXATC); |
| adapter->stats.ictxptc += rd32(E1000_ICTXPTC); |
| adapter->stats.ictxatc += rd32(E1000_ICTXATC); |
| adapter->stats.ictxqec += rd32(E1000_ICTXQEC); |
| adapter->stats.ictxqmtc += rd32(E1000_ICTXQMTC); |
| adapter->stats.icrxdmtc += rd32(E1000_ICRXDMTC); |
| |
| /* Fill out the OS statistics structure */ |
| net_stats->multicast = adapter->stats.mprc; |
| net_stats->collisions = adapter->stats.colc; |
| |
| /* Rx Errors */ |
| |
| /* RLEC on some newer hardware can be incorrect so build |
| * our own version based on RUC and ROC |
| */ |
| net_stats->rx_errors = adapter->stats.rxerrc + |
| adapter->stats.crcerrs + adapter->stats.algnerrc + |
| adapter->stats.ruc + adapter->stats.roc + |
| adapter->stats.cexterr; |
| net_stats->rx_length_errors = adapter->stats.ruc + |
| adapter->stats.roc; |
| net_stats->rx_crc_errors = adapter->stats.crcerrs; |
| net_stats->rx_frame_errors = adapter->stats.algnerrc; |
| net_stats->rx_missed_errors = adapter->stats.mpc; |
| |
| /* Tx Errors */ |
| net_stats->tx_errors = adapter->stats.ecol + |
| adapter->stats.latecol; |
| net_stats->tx_aborted_errors = adapter->stats.ecol; |
| net_stats->tx_window_errors = adapter->stats.latecol; |
| net_stats->tx_carrier_errors = adapter->stats.tncrs; |
| |
| /* Tx Dropped needs to be maintained elsewhere */ |
| |
| /* Management Stats */ |
| adapter->stats.mgptc += rd32(E1000_MGTPTC); |
| adapter->stats.mgprc += rd32(E1000_MGTPRC); |
| adapter->stats.mgpdc += rd32(E1000_MGTPDC); |
| |
| /* OS2BMC Stats */ |
| reg = rd32(E1000_MANC); |
| if (reg & E1000_MANC_EN_BMC2OS) { |
| adapter->stats.o2bgptc += rd32(E1000_O2BGPTC); |
| adapter->stats.o2bspc += rd32(E1000_O2BSPC); |
| adapter->stats.b2ospc += rd32(E1000_B2OSPC); |
| adapter->stats.b2ogprc += rd32(E1000_B2OGPRC); |
| } |
| } |
| |
| static void igb_perout(struct igb_adapter *adapter, int tsintr_tt) |
| { |
| int pin = ptp_find_pin(adapter->ptp_clock, PTP_PF_PEROUT, tsintr_tt); |
| struct e1000_hw *hw = &adapter->hw; |
| struct timespec64 ts; |
| u32 tsauxc; |
| |
| if (pin < 0 || pin >= IGB_N_SDP) |
| return; |
| |
| spin_lock(&adapter->tmreg_lock); |
| |
| if (hw->mac.type == e1000_82580 || |
| hw->mac.type == e1000_i354 || |
| hw->mac.type == e1000_i350) { |
| s64 ns = timespec64_to_ns(&adapter->perout[tsintr_tt].period); |
| u32 systiml, systimh, level_mask, level, rem; |
| u64 systim, now; |
| |
| /* read systim registers in sequence */ |
| rd32(E1000_SYSTIMR); |
| systiml = rd32(E1000_SYSTIML); |
| systimh = rd32(E1000_SYSTIMH); |
| systim = (((u64)(systimh & 0xFF)) << 32) | ((u64)systiml); |
| now = timecounter_cyc2time(&adapter->tc, systim); |
| |
| if (pin < 2) { |
| level_mask = (tsintr_tt == 1) ? 0x80000 : 0x40000; |
| level = (rd32(E1000_CTRL) & level_mask) ? 1 : 0; |
| } else { |
| level_mask = (tsintr_tt == 1) ? 0x80 : 0x40; |
| level = (rd32(E1000_CTRL_EXT) & level_mask) ? 1 : 0; |
| } |
| |
| div_u64_rem(now, ns, &rem); |
| systim = systim + (ns - rem); |
| |
| /* synchronize pin level with rising/falling edges */ |
| div_u64_rem(now, ns << 1, &rem); |
| if (rem < ns) { |
| /* first half of period */ |
| if (level == 0) { |
| /* output is already low, skip this period */ |
| systim += ns; |
| pr_notice("igb: periodic output on %s missed falling edge\n", |
| adapter->sdp_config[pin].name); |
| } |
| } else { |
| /* second half of period */ |
| if (level == 1) { |
| /* output is already high, skip this period */ |
| systim += ns; |
| pr_notice("igb: periodic output on %s missed rising edge\n", |
| adapter->sdp_config[pin].name); |
| } |
| } |
| |
| /* for this chip family tv_sec is the upper part of the binary value, |
| * so not seconds |
| */ |
| ts.tv_nsec = (u32)systim; |
| ts.tv_sec = ((u32)(systim >> 32)) & 0xFF; |
| } else { |
| ts = timespec64_add(adapter->perout[tsintr_tt].start, |
| adapter->perout[tsintr_tt].period); |
| } |
| |
| /* u32 conversion of tv_sec is safe until y2106 */ |
| wr32((tsintr_tt == 1) ? E1000_TRGTTIML1 : E1000_TRGTTIML0, ts.tv_nsec); |
| wr32((tsintr_tt == 1) ? E1000_TRGTTIMH1 : E1000_TRGTTIMH0, (u32)ts.tv_sec); |
| tsauxc = rd32(E1000_TSAUXC); |
| tsauxc |= TSAUXC_EN_TT0; |
| wr32(E1000_TSAUXC, tsauxc); |
| adapter->perout[tsintr_tt].start = ts; |
| |
| spin_unlock(&adapter->tmreg_lock); |
| } |
| |
| static void igb_extts(struct igb_adapter *adapter, int tsintr_tt) |
| { |
| int pin = ptp_find_pin(adapter->ptp_clock, PTP_PF_EXTTS, tsintr_tt); |
| int auxstmpl = (tsintr_tt == 1) ? E1000_AUXSTMPL1 : E1000_AUXSTMPL0; |
| int auxstmph = (tsintr_tt == 1) ? E1000_AUXSTMPH1 : E1000_AUXSTMPH0; |
| struct e1000_hw *hw = &adapter->hw; |
| struct ptp_clock_event event; |
| struct timespec64 ts; |
| unsigned long flags; |
| |
| if (pin < 0 || pin >= IGB_N_SDP) |
| return; |
| |
| if (hw->mac.type == e1000_82580 || |
| hw->mac.type == e1000_i354 || |
| hw->mac.type == e1000_i350) { |
| u64 ns = rd32(auxstmpl); |
| |
| ns += ((u64)(rd32(auxstmph) & 0xFF)) << 32; |
| spin_lock_irqsave(&adapter->tmreg_lock, flags); |
| ns = timecounter_cyc2time(&adapter->tc, ns); |
| spin_unlock_irqrestore(&adapter->tmreg_lock, flags); |
| ts = ns_to_timespec64(ns); |
| } else { |
| ts.tv_nsec = rd32(auxstmpl); |
| ts.tv_sec = rd32(auxstmph); |
| } |
| |
| event.type = PTP_CLOCK_EXTTS; |
| event.index = tsintr_tt; |
| event.timestamp = ts.tv_sec * 1000000000ULL + ts.tv_nsec; |
| ptp_clock_event(adapter->ptp_clock, &event); |
| } |
| |
| static void igb_tsync_interrupt(struct igb_adapter *adapter) |
| { |
| const u32 mask = (TSINTR_SYS_WRAP | E1000_TSICR_TXTS | |
| TSINTR_TT0 | TSINTR_TT1 | |
| TSINTR_AUTT0 | TSINTR_AUTT1); |
| struct e1000_hw *hw = &adapter->hw; |
| u32 tsicr = rd32(E1000_TSICR); |
| struct ptp_clock_event event; |
| |
| if (hw->mac.type == e1000_82580) { |
| /* 82580 has a hardware bug that requires an explicit |
| * write to clear the TimeSync interrupt cause. |
| */ |
| wr32(E1000_TSICR, tsicr & mask); |
| } |
| |
| if (tsicr & TSINTR_SYS_WRAP) { |
| event.type = PTP_CLOCK_PPS; |
| if (adapter->ptp_caps.pps) |
| ptp_clock_event(adapter->ptp_clock, &event); |
| } |
| |
| if (tsicr & E1000_TSICR_TXTS) { |
| /* retrieve hardware timestamp */ |
| schedule_work(&adapter->ptp_tx_work); |
| } |
| |
| if (tsicr & TSINTR_TT0) |
| igb_perout(adapter, 0); |
| |
| if (tsicr & TSINTR_TT1) |
| igb_perout(adapter, 1); |
| |
| if (tsicr & TSINTR_AUTT0) |
| igb_extts(adapter, 0); |
| |
| if (tsicr & TSINTR_AUTT1) |
| igb_extts(adapter, 1); |
| } |
| |
| static irqreturn_t igb_msix_other(int irq, void *data) |
| { |
| struct igb_adapter *adapter = data; |
| struct e1000_hw *hw = &adapter->hw; |
| u32 icr = rd32(E1000_ICR); |
| /* reading ICR causes bit 31 of EICR to be cleared */ |
| |
| if (icr & E1000_ICR_DRSTA) |
| schedule_work(&adapter->reset_task); |
| |
| if (icr & E1000_ICR_DOUTSYNC) { |
| /* HW is reporting DMA is out of sync */ |
| adapter->stats.doosync++; |
| /* The DMA Out of Sync is also indication of a spoof event |
| * in IOV mode. Check the Wrong VM Behavior register to |
| * see if it is really a spoof event. |
| */ |
| igb_check_wvbr(adapter); |
| } |
| |
| /* Check for a mailbox event */ |
| if (icr & E1000_ICR_VMMB) |
| igb_msg_task(adapter); |
| |
| if (icr & E1000_ICR_LSC) { |
| hw->mac.get_link_status = 1; |
| /* guard against interrupt when we're going down */ |
| if (!test_bit(__IGB_DOWN, &adapter->state)) |
| mod_timer(&adapter->watchdog_timer, jiffies + 1); |
| } |
| |
| if (icr & E1000_ICR_TS) |
| igb_tsync_interrupt(adapter); |
| |
| wr32(E1000_EIMS, adapter->eims_other); |
| |
| return IRQ_HANDLED; |
| } |
| |
| static void igb_write_itr(struct igb_q_vector *q_vector) |
| { |
| struct igb_adapter *adapter = q_vector->adapter; |
| u32 itr_val = q_vector->itr_val & 0x7FFC; |
| |
| if (!q_vector->set_itr) |
| return; |
| |
| if (!itr_val) |
| itr_val = 0x4; |
| |
| if (adapter->hw.mac.type == e1000_82575) |
| itr_val |= itr_val << 16; |
| else |
| itr_val |= E1000_EITR_CNT_IGNR; |
| |
| writel(itr_val, q_vector->itr_register); |
| q_vector->set_itr = 0; |
| } |
| |
| static irqreturn_t igb_msix_ring(int irq, void *data) |
| { |
| struct igb_q_vector *q_vector = data; |
| |
| /* Write the ITR value calculated from the previous interrupt. */ |
| igb_write_itr(q_vector); |
| |
| napi_schedule(&q_vector->napi); |
| |
| return IRQ_HANDLED; |
| } |
| |
| #ifdef CONFIG_IGB_DCA |
| static void igb_update_tx_dca(struct igb_adapter *adapter, |
| struct igb_ring *tx_ring, |
| int cpu) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| u32 txctrl = dca3_get_tag(tx_ring->dev, cpu); |
| |
| if (hw->mac.type != e1000_82575) |
| txctrl <<= E1000_DCA_TXCTRL_CPUID_SHIFT; |
| |
| /* We can enable relaxed ordering for reads, but not writes when |
| * DCA is enabled. This is due to a known issue in some chipsets |
| * which will cause the DCA tag to be cleared. |
| */ |
| txctrl |= E1000_DCA_TXCTRL_DESC_RRO_EN | |
| E1000_DCA_TXCTRL_DATA_RRO_EN | |
| E1000_DCA_TXCTRL_DESC_DCA_EN; |
| |
| wr32(E1000_DCA_TXCTRL(tx_ring->reg_idx), txctrl); |
| } |
| |
| static void igb_update_rx_dca(struct igb_adapter *adapter, |
| struct igb_ring *rx_ring, |
| int cpu) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| u32 rxctrl = dca3_get_tag(&adapter->pdev->dev, cpu); |
| |
| if (hw->mac.type != e1000_82575) |
| rxctrl <<= E1000_DCA_RXCTRL_CPUID_SHIFT; |
| |
| /* We can enable relaxed ordering for reads, but not writes when |
| * DCA is enabled. This is due to a known issue in some chipsets |
| * which will cause the DCA tag to be cleared. |
| */ |
| rxctrl |= E1000_DCA_RXCTRL_DESC_RRO_EN | |
| E1000_DCA_RXCTRL_DESC_DCA_EN; |
| |
| wr32(E1000_DCA_RXCTRL(rx_ring->reg_idx), rxctrl); |
| } |
| |
| static void igb_update_dca(struct igb_q_vector *q_vector) |
| { |
| struct igb_adapter *adapter = q_vector->adapter; |
| int cpu = get_cpu(); |
| |
| if (q_vector->cpu == cpu) |
| goto out_no_update; |
| |
| if (q_vector->tx.ring) |
| igb_update_tx_dca(adapter, q_vector->tx.ring, cpu); |
| |
| if (q_vector->rx.ring) |
| igb_update_rx_dca(adapter, q_vector->rx.ring, cpu); |
| |
| q_vector->cpu = cpu; |
| out_no_update: |
| put_cpu(); |
| } |
| |
| static void igb_setup_dca(struct igb_adapter *adapter) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| int i; |
| |
| if (!(adapter->flags & IGB_FLAG_DCA_ENABLED)) |
| return; |
| |
| /* Always use CB2 mode, difference is masked in the CB driver. */ |
| wr32(E1000_DCA_CTRL, E1000_DCA_CTRL_DCA_MODE_CB2); |
| |
| for (i = 0; i < adapter->num_q_vectors; i++) { |
| adapter->q_vector[i]->cpu = -1; |
| igb_update_dca(adapter->q_vector[i]); |
| } |
| } |
| |
| static int __igb_notify_dca(struct device *dev, void *data) |
| { |
| struct net_device *netdev = dev_get_drvdata(dev); |
| struct igb_adapter *adapter = netdev_priv(netdev); |
| struct pci_dev *pdev = adapter->pdev; |
| struct e1000_hw *hw = &adapter->hw; |
| unsigned long event = *(unsigned long *)data; |
| |
| switch (event) { |
| case DCA_PROVIDER_ADD: |
| /* if already enabled, don't do it again */ |
| if (adapter->flags & IGB_FLAG_DCA_ENABLED) |
| break; |
| if (dca_add_requester(dev) == 0) { |
| adapter->flags |= IGB_FLAG_DCA_ENABLED; |
| dev_info(&pdev->dev, "DCA enabled\n"); |
| igb_setup_dca(adapter); |
| break; |
| } |
| fallthrough; /* since DCA is disabled. */ |
| case DCA_PROVIDER_REMOVE: |
| if (adapter->flags & IGB_FLAG_DCA_ENABLED) { |
| /* without this a class_device is left |
| * hanging around in the sysfs model |
| */ |
| dca_remove_requester(dev); |
| dev_info(&pdev->dev, "DCA disabled\n"); |
| adapter->flags &= ~IGB_FLAG_DCA_ENABLED; |
| wr32(E1000_DCA_CTRL, E1000_DCA_CTRL_DCA_MODE_DISABLE); |
| } |
| break; |
| } |
| |
| return 0; |
| } |
| |
| static int igb_notify_dca(struct notifier_block *nb, unsigned long event, |
| void *p) |
| { |
| int ret_val; |
| |
| ret_val = driver_for_each_device(&igb_driver.driver, NULL, &event, |
| __igb_notify_dca); |
| |
| return ret_val ? NOTIFY_BAD : NOTIFY_DONE; |
| } |
| #endif /* CONFIG_IGB_DCA */ |
| |
| #ifdef CONFIG_PCI_IOV |
| static int igb_vf_configure(struct igb_adapter *adapter, int vf) |
| { |
| unsigned char mac_addr[ETH_ALEN]; |
| |
| eth_zero_addr(mac_addr); |
| igb_set_vf_mac(adapter, vf, mac_addr); |
| |
| /* By default spoof check is enabled for all VFs */ |
| adapter->vf_data[vf].spoofchk_enabled = true; |
| |
| /* By default VFs are not trusted */ |
| adapter->vf_data[vf].trusted = false; |
| |
| return 0; |
| } |
| |
| #endif |
| static void igb_ping_all_vfs(struct igb_adapter *adapter) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| u32 ping; |
| int i; |
| |
| for (i = 0 ; i < adapter->vfs_allocated_count; i++) { |
| ping = E1000_PF_CONTROL_MSG; |
| if (adapter->vf_data[i].flags & IGB_VF_FLAG_CTS) |
| ping |= E1000_VT_MSGTYPE_CTS; |
| igb_write_mbx(hw, &ping, 1, i); |
| } |
| } |
| |
| static int igb_set_vf_promisc(struct igb_adapter *adapter, u32 *msgbuf, u32 vf) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| u32 vmolr = rd32(E1000_VMOLR(vf)); |
| struct vf_data_storage *vf_data = &adapter->vf_data[vf]; |
| |
| vf_data->flags &= ~(IGB_VF_FLAG_UNI_PROMISC | |
| IGB_VF_FLAG_MULTI_PROMISC); |
| vmolr &= ~(E1000_VMOLR_ROPE | E1000_VMOLR_ROMPE | E1000_VMOLR_MPME); |
| |
| if (*msgbuf & E1000_VF_SET_PROMISC_MULTICAST) { |
| vmolr |= E1000_VMOLR_MPME; |
| vf_data->flags |= IGB_VF_FLAG_MULTI_PROMISC; |
| *msgbuf &= ~E1000_VF_SET_PROMISC_MULTICAST; |
| } else { |
| /* if we have hashes and we are clearing a multicast promisc |
| * flag we need to write the hashes to the MTA as this step |
| * was previously skipped |
| */ |
| if (vf_data->num_vf_mc_hashes > 30) { |
| vmolr |= E1000_VMOLR_MPME; |
| } else if (vf_data->num_vf_mc_hashes) { |
| int j; |
| |
| vmolr |= E1000_VMOLR_ROMPE; |
| for (j = 0; j < vf_data->num_vf_mc_hashes; j++) |
| igb_mta_set(hw, vf_data->vf_mc_hashes[j]); |
| } |
| } |
| |
| wr32(E1000_VMOLR(vf), vmolr); |
| |
| /* there are flags left unprocessed, likely not supported */ |
| if (*msgbuf & E1000_VT_MSGINFO_MASK) |
| return -EINVAL; |
| |
| return 0; |
| } |
| |
| static int igb_set_vf_multicasts(struct igb_adapter *adapter, |
| u32 *msgbuf, u32 vf) |
| { |
| int n = FIELD_GET(E1000_VT_MSGINFO_MASK, msgbuf[0]); |
| u16 *hash_list = (u16 *)&msgbuf[1]; |
| struct vf_data_storage *vf_data = &adapter->vf_data[vf]; |
| int i; |
| |
| /* salt away the number of multicast addresses assigned |
| * to this VF for later use to restore when the PF multi cast |
| * list changes |
| */ |
| vf_data->num_vf_mc_hashes = n; |
| |
| /* only up to 30 hash values supported */ |
| if (n > 30) |
| n = 30; |
| |
| /* store the hashes for later use */ |
| for (i = 0; i < n; i++) |
| vf_data->vf_mc_hashes[i] = hash_list[i]; |
| |
| /* Flush and reset the mta with the new values */ |
| igb_set_rx_mode(adapter->netdev); |
| |
| return 0; |
| } |
| |
| static void igb_restore_vf_multicasts(struct igb_adapter *adapter) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| struct vf_data_storage *vf_data; |
| int i, j; |
| |
| for (i = 0; i < adapter->vfs_allocated_count; i++) { |
| u32 vmolr = rd32(E1000_VMOLR(i)); |
| |
| vmolr &= ~(E1000_VMOLR_ROMPE | E1000_VMOLR_MPME); |
| |
| vf_data = &adapter->vf_data[i]; |
| |
| if ((vf_data->num_vf_mc_hashes > 30) || |
| (vf_data->flags & IGB_VF_FLAG_MULTI_PROMISC)) { |
| vmolr |= E1000_VMOLR_MPME; |
| } else if (vf_data->num_vf_mc_hashes) { |
| vmolr |= E1000_VMOLR_ROMPE; |
| for (j = 0; j < vf_data->num_vf_mc_hashes; j++) |
| igb_mta_set(hw, vf_data->vf_mc_hashes[j]); |
| } |
| wr32(E1000_VMOLR(i), vmolr); |
| } |
| } |
| |
| static void igb_clear_vf_vfta(struct igb_adapter *adapter, u32 vf) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| u32 pool_mask, vlvf_mask, i; |
| |
| /* create mask for VF and other pools */ |
| pool_mask = E1000_VLVF_POOLSEL_MASK; |
| vlvf_mask = BIT(E1000_VLVF_POOLSEL_SHIFT + vf); |
| |
| /* drop PF from pool bits */ |
| pool_mask &= ~BIT(E1000_VLVF_POOLSEL_SHIFT + |
| adapter->vfs_allocated_count); |
| |
| /* Find the vlan filter for this id */ |
| for (i = E1000_VLVF_ARRAY_SIZE; i--;) { |
| u32 vlvf = rd32(E1000_VLVF(i)); |
| u32 vfta_mask, vid, vfta; |
| |
| /* remove the vf from the pool */ |
| if (!(vlvf & vlvf_mask)) |
| continue; |
| |
| /* clear out bit from VLVF */ |
| vlvf ^= vlvf_mask; |
| |
| /* if other pools are present, just remove ourselves */ |
| if (vlvf & pool_mask) |
| goto update_vlvfb; |
| |
| /* if PF is present, leave VFTA */ |
| if (vlvf & E1000_VLVF_POOLSEL_MASK) |
| goto update_vlvf; |
| |
| vid = vlvf & E1000_VLVF_VLANID_MASK; |
| vfta_mask = BIT(vid % 32); |
| |
| /* clear bit from VFTA */ |
| vfta = adapter->shadow_vfta[vid / 32]; |
| if (vfta & vfta_mask) |
| hw->mac.ops.write_vfta(hw, vid / 32, vfta ^ vfta_mask); |
| update_vlvf: |
| /* clear pool selection enable */ |
| if (adapter->flags & IGB_FLAG_VLAN_PROMISC) |
| vlvf &= E1000_VLVF_POOLSEL_MASK; |
| else |
| vlvf = 0; |
| update_vlvfb: |
| /* clear pool bits */ |
| wr32(E1000_VLVF(i), vlvf); |
| } |
| } |
| |
| static int igb_find_vlvf_entry(struct e1000_hw *hw, u32 vlan) |
| { |
| u32 vlvf; |
| int idx; |
| |
| /* short cut the special case */ |
| if (vlan == 0) |
| return 0; |
| |
| /* Search for the VLAN id in the VLVF entries */ |
| for (idx = E1000_VLVF_ARRAY_SIZE; --idx;) { |
| vlvf = rd32(E1000_VLVF(idx)); |
| if ((vlvf & VLAN_VID_MASK) == vlan) |
| break; |
| } |
| |
| return idx; |
| } |
| |
| static void igb_update_pf_vlvf(struct igb_adapter *adapter, u32 vid) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| u32 bits, pf_id; |
| int idx; |
| |
| idx = igb_find_vlvf_entry(hw, vid); |
| if (!idx) |
| return; |
| |
| /* See if any other pools are set for this VLAN filter |
| * entry other than the PF. |
| */ |
| pf_id = adapter->vfs_allocated_count + E1000_VLVF_POOLSEL_SHIFT; |
| bits = ~BIT(pf_id) & E1000_VLVF_POOLSEL_MASK; |
| bits &= rd32(E1000_VLVF(idx)); |
| |
| /* Disable the filter so this falls into the default pool. */ |
| if (!bits) { |
| if (adapter->flags & IGB_FLAG_VLAN_PROMISC) |
| wr32(E1000_VLVF(idx), BIT(pf_id)); |
| else |
| wr32(E1000_VLVF(idx), 0); |
| } |
| } |
| |
| static s32 igb_set_vf_vlan(struct igb_adapter *adapter, u32 vid, |
| bool add, u32 vf) |
| { |
| int pf_id = adapter->vfs_allocated_count; |
| struct e1000_hw *hw = &adapter->hw; |
| int err; |
| |
| /* If VLAN overlaps with one the PF is currently monitoring make |
| * sure that we are able to allocate a VLVF entry. This may be |
| * redundant but it guarantees PF will maintain visibility to |
| * the VLAN. |
| */ |
| if (add && test_bit(vid, adapter->active_vlans)) { |
| err = igb_vfta_set(hw, vid, pf_id, true, false); |
| if (err) |
| return err; |
| } |
| |
| err = igb_vfta_set(hw, vid, vf, add, false); |
| |
| if (add && !err) |
| return err; |
| |
| /* If we failed to add the VF VLAN or we are removing the VF VLAN |
| * we may need to drop the PF pool bit in order to allow us to free |
| * up the VLVF resources. |
| */ |
| if (test_bit(vid, adapter->active_vlans) || |
| (adapter->flags & IGB_FLAG_VLAN_PROMISC)) |
| igb_update_pf_vlvf(adapter, vid); |
| |
| return err; |
| } |
| |
| static void igb_set_vmvir(struct igb_adapter *adapter, u32 vid, u32 vf) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| |
| if (vid) |
| wr32(E1000_VMVIR(vf), (vid | E1000_VMVIR_VLANA_DEFAULT)); |
| else |
| wr32(E1000_VMVIR(vf), 0); |
| } |
| |
| static int igb_enable_port_vlan(struct igb_adapter *adapter, int vf, |
| u16 vlan, u8 qos) |
| { |
| int err; |
| |
| err = igb_set_vf_vlan(adapter, vlan, true, vf); |
| if (err) |
| return err; |
| |
| igb_set_vmvir(adapter, vlan | (qos << VLAN_PRIO_SHIFT), vf); |
| igb_set_vmolr(adapter, vf, !vlan); |
| |
| /* revoke access to previous VLAN */ |
| if (vlan != adapter->vf_data[vf].pf_vlan) |
| igb_set_vf_vlan(adapter, adapter->vf_data[vf].pf_vlan, |
| false, vf); |
| |
| adapter->vf_data[vf].pf_vlan = vlan; |
| adapter->vf_data[vf].pf_qos = qos; |
| igb_set_vf_vlan_strip(adapter, vf, true); |
| dev_info(&adapter->pdev->dev, |
| "Setting VLAN %d, QOS 0x%x on VF %d\n", vlan, qos, vf); |
| if (test_bit(__IGB_DOWN, &adapter->state)) { |
| dev_warn(&adapter->pdev->dev, |
| "The VF VLAN has been set, but the PF device is not up.\n"); |
| dev_warn(&adapter->pdev->dev, |
| "Bring the PF device up before attempting to use the VF device.\n"); |
| } |
| |
| return err; |
| } |
| |
| static int igb_disable_port_vlan(struct igb_adapter *adapter, int vf) |
| { |
| /* Restore tagless access via VLAN 0 */ |
| igb_set_vf_vlan(adapter, 0, true, vf); |
| |
| igb_set_vmvir(adapter, 0, vf); |
| igb_set_vmolr(adapter, vf, true); |
| |
| /* Remove any PF assigned VLAN */ |
| if (adapter->vf_data[vf].pf_vlan) |
| igb_set_vf_vlan(adapter, adapter->vf_data[vf].pf_vlan, |
| false, vf); |
| |
| adapter->vf_data[vf].pf_vlan = 0; |
| adapter->vf_data[vf].pf_qos = 0; |
| igb_set_vf_vlan_strip(adapter, vf, false); |
| |
| return 0; |
| } |
| |
| static int igb_ndo_set_vf_vlan(struct net_device *netdev, int vf, |
| u16 vlan, u8 qos, __be16 vlan_proto) |
| { |
| struct igb_adapter *adapter = netdev_priv(netdev); |
| |
| if ((vf >= adapter->vfs_allocated_count) || (vlan > 4095) || (qos > 7)) |
| return -EINVAL; |
| |
| if (vlan_proto != htons(ETH_P_8021Q)) |
| return -EPROTONOSUPPORT; |
| |
| return (vlan || qos) ? igb_enable_port_vlan(adapter, vf, vlan, qos) : |
| igb_disable_port_vlan(adapter, vf); |
| } |
| |
| static int igb_set_vf_vlan_msg(struct igb_adapter *adapter, u32 *msgbuf, u32 vf) |
| { |
| int add = FIELD_GET(E1000_VT_MSGINFO_MASK, msgbuf[0]); |
| int vid = (msgbuf[1] & E1000_VLVF_VLANID_MASK); |
| int ret; |
| |
| if (adapter->vf_data[vf].pf_vlan) |
| return -1; |
| |
| /* VLAN 0 is a special case, don't allow it to be removed */ |
| if (!vid && !add) |
| return 0; |
| |
| ret = igb_set_vf_vlan(adapter, vid, !!add, vf); |
| if (!ret) |
| igb_set_vf_vlan_strip(adapter, vf, !!vid); |
| return ret; |
| } |
| |
| static inline void igb_vf_reset(struct igb_adapter *adapter, u32 vf) |
| { |
| struct vf_data_storage *vf_data = &adapter->vf_data[vf]; |
| |
| /* clear flags - except flag that indicates PF has set the MAC */ |
| vf_data->flags &= IGB_VF_FLAG_PF_SET_MAC; |
| vf_data->last_nack = jiffies; |
| |
| /* reset vlans for device */ |
| igb_clear_vf_vfta(adapter, vf); |
| igb_set_vf_vlan(adapter, vf_data->pf_vlan, true, vf); |
| igb_set_vmvir(adapter, vf_data->pf_vlan | |
| (vf_data->pf_qos << VLAN_PRIO_SHIFT), vf); |
| igb_set_vmolr(adapter, vf, !vf_data->pf_vlan); |
| igb_set_vf_vlan_strip(adapter, vf, !!(vf_data->pf_vlan)); |
| |
| /* reset multicast table array for vf */ |
| adapter->vf_data[vf].num_vf_mc_hashes = 0; |
| |
| /* Flush and reset the mta with the new values */ |
| igb_set_rx_mode(adapter->netdev); |
| } |
| |
| static void igb_vf_reset_event(struct igb_adapter *adapter, u32 vf) |
| { |
| unsigned char *vf_mac = adapter->vf_data[vf].vf_mac_addresses; |
| |
| /* clear mac address as we were hotplug removed/added */ |
| if (!(adapter->vf_data[vf].flags & IGB_VF_FLAG_PF_SET_MAC)) |
| eth_zero_addr(vf_mac); |
| |
| /* process remaining reset events */ |
| igb_vf_reset(adapter, vf); |
| } |
| |
| static void igb_vf_reset_msg(struct igb_adapter *adapter, u32 vf) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| unsigned char *vf_mac = adapter->vf_data[vf].vf_mac_addresses; |
| u32 reg, msgbuf[3] = {}; |
| u8 *addr = (u8 *)(&msgbuf[1]); |
| |
| /* process all the same items cleared in a function level reset */ |
| igb_vf_reset(adapter, vf); |
| |
| /* set vf mac address */ |
| igb_set_vf_mac(adapter, vf, vf_mac); |
| |
| /* enable transmit and receive for vf */ |
| reg = rd32(E1000_VFTE); |
| wr32(E1000_VFTE, reg | BIT(vf)); |
| reg = rd32(E1000_VFRE); |
| wr32(E1000_VFRE, reg | BIT(vf)); |
| |
| adapter->vf_data[vf].flags |= IGB_VF_FLAG_CTS; |
| |
| /* reply to reset with ack and vf mac address */ |
| if (!is_zero_ether_addr(vf_mac)) { |
| msgbuf[0] = E1000_VF_RESET | E1000_VT_MSGTYPE_ACK; |
| memcpy(addr, vf_mac, ETH_ALEN); |
| } else { |
| msgbuf[0] = E1000_VF_RESET | E1000_VT_MSGTYPE_NACK; |
| } |
| igb_write_mbx(hw, msgbuf, 3, vf); |
| } |
| |
| static void igb_flush_mac_table(struct igb_adapter *adapter) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| int i; |
| |
| for (i = 0; i < hw->mac.rar_entry_count; i++) { |
| adapter->mac_table[i].state &= ~IGB_MAC_STATE_IN_USE; |
| eth_zero_addr(adapter->mac_table[i].addr); |
| adapter->mac_table[i].queue = 0; |
| igb_rar_set_index(adapter, i); |
| } |
| } |
| |
| static int igb_available_rars(struct igb_adapter *adapter, u8 queue) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| /* do not count rar entries reserved for VFs MAC addresses */ |
| int rar_entries = hw->mac.rar_entry_count - |
| adapter->vfs_allocated_count; |
| int i, count = 0; |
| |
| for (i = 0; i < rar_entries; i++) { |
| /* do not count default entries */ |
| if (adapter->mac_table[i].state & IGB_MAC_STATE_DEFAULT) |
| continue; |
| |
| /* do not count "in use" entries for different queues */ |
| if ((adapter->mac_table[i].state & IGB_MAC_STATE_IN_USE) && |
| (adapter->mac_table[i].queue != queue)) |
| continue; |
| |
| count++; |
| } |
| |
| return count; |
| } |
| |
| /* Set default MAC address for the PF in the first RAR entry */ |
| static void igb_set_default_mac_filter(struct igb_adapter *adapter) |
| { |
| struct igb_mac_addr *mac_table = &adapter->mac_table[0]; |
| |
| ether_addr_copy(mac_table->addr, adapter->hw.mac.addr); |
| mac_table->queue = adapter->vfs_allocated_count; |
| mac_table->state = IGB_MAC_STATE_DEFAULT | IGB_MAC_STATE_IN_USE; |
| |
| igb_rar_set_index(adapter, 0); |
| } |
| |
| /* If the filter to be added and an already existing filter express |
| * the same address and address type, it should be possible to only |
| * override the other configurations, for example the queue to steer |
| * traffic. |
| */ |
| static bool igb_mac_entry_can_be_used(const struct igb_mac_addr *entry, |
| const u8 *addr, const u8 flags) |
| { |
| if (!(entry->state & IGB_MAC_STATE_IN_USE)) |
| return true; |
| |
| if ((entry->state & IGB_MAC_STATE_SRC_ADDR) != |
| (flags & IGB_MAC_STATE_SRC_ADDR)) |
| return false; |
| |
| if (!ether_addr_equal(addr, entry->addr)) |
| return false; |
| |
| return true; |
| } |
| |
| /* Add a MAC filter for 'addr' directing matching traffic to 'queue', |
| * 'flags' is used to indicate what kind of match is made, match is by |
| * default for the destination address, if matching by source address |
| * is desired the flag IGB_MAC_STATE_SRC_ADDR can be used. |
| */ |
| static int igb_add_mac_filter_flags(struct igb_adapter *adapter, |
| const u8 *addr, const u8 queue, |
| const u8 flags) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| int rar_entries = hw->mac.rar_entry_count - |
| adapter->vfs_allocated_count; |
| int i; |
| |
| if (is_zero_ether_addr(addr)) |
| return -EINVAL; |
| |
| /* Search for the first empty entry in the MAC table. |
| * Do not touch entries at the end of the table reserved for the VF MAC |
| * addresses. |
| */ |
| for (i = 0; i < rar_entries; i++) { |
| if (!igb_mac_entry_can_be_used(&adapter->mac_table[i], |
| addr, flags)) |
| continue; |
| |
| ether_addr_copy(adapter->mac_table[i].addr, addr); |
| adapter->mac_table[i].queue = queue; |
| adapter->mac_table[i].state |= IGB_MAC_STATE_IN_USE | flags; |
| |
| igb_rar_set_index(adapter, i); |
| return i; |
| } |
| |
| return -ENOSPC; |
| } |
| |
| static int igb_add_mac_filter(struct igb_adapter *adapter, const u8 *addr, |
| const u8 queue) |
| { |
| return igb_add_mac_filter_flags(adapter, addr, queue, 0); |
| } |
| |
| /* Remove a MAC filter for 'addr' directing matching traffic to |
| * 'queue', 'flags' is used to indicate what kind of match need to be |
| * removed, match is by default for the destination address, if |
| * matching by source address is to be removed the flag |
| * IGB_MAC_STATE_SRC_ADDR can be used. |
| */ |
| static int igb_del_mac_filter_flags(struct igb_adapter *adapter, |
| const u8 *addr, const u8 queue, |
| const u8 flags) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| int rar_entries = hw->mac.rar_entry_count - |
| adapter->vfs_allocated_count; |
| int i; |
| |
| if (is_zero_ether_addr(addr)) |
| return -EINVAL; |
| |
| /* Search for matching entry in the MAC table based on given address |
| * and queue. Do not touch entries at the end of the table reserved |
| * for the VF MAC addresses. |
| */ |
| for (i = 0; i < rar_entries; i++) { |
| if (!(adapter->mac_table[i].state & IGB_MAC_STATE_IN_USE)) |
| continue; |
| if ((adapter->mac_table[i].state & flags) != flags) |
| continue; |
| if (adapter->mac_table[i].queue != queue) |
| continue; |
| if (!ether_addr_equal(adapter->mac_table[i].addr, addr)) |
| continue; |
| |
| /* When a filter for the default address is "deleted", |
| * we return it to its initial configuration |
| */ |
| if (adapter->mac_table[i].state & IGB_MAC_STATE_DEFAULT) { |
| adapter->mac_table[i].state = |
| IGB_MAC_STATE_DEFAULT | IGB_MAC_STATE_IN_USE; |
| adapter->mac_table[i].queue = |
| adapter->vfs_allocated_count; |
| } else { |
| adapter->mac_table[i].state = 0; |
| adapter->mac_table[i].queue = 0; |
| eth_zero_addr(adapter->mac_table[i].addr); |
| } |
| |
| igb_rar_set_index(adapter, i); |
| return 0; |
| } |
| |
| return -ENOENT; |
| } |
| |
| static int igb_del_mac_filter(struct igb_adapter *adapter, const u8 *addr, |
| const u8 queue) |
| { |
| return igb_del_mac_filter_flags(adapter, addr, queue, 0); |
| } |
| |
| int igb_add_mac_steering_filter(struct igb_adapter *adapter, |
| const u8 *addr, u8 queue, u8 flags) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| |
| /* In theory, this should be supported on 82575 as well, but |
| * that part wasn't easily accessible during development. |
| */ |
| if (hw->mac.type != e1000_i210) |
| return -EOPNOTSUPP; |
| |
| return igb_add_mac_filter_flags(adapter, addr, queue, |
| IGB_MAC_STATE_QUEUE_STEERING | flags); |
| } |
| |
| int igb_del_mac_steering_filter(struct igb_adapter *adapter, |
| const u8 *addr, u8 queue, u8 flags) |
| { |
| return igb_del_mac_filter_flags(adapter, addr, queue, |
| IGB_MAC_STATE_QUEUE_STEERING | flags); |
| } |
| |
| static int igb_uc_sync(struct net_device *netdev, const unsigned char *addr) |
| { |
| struct igb_adapter *adapter = netdev_priv(netdev); |
| int ret; |
| |
| ret = igb_add_mac_filter(adapter, addr, adapter->vfs_allocated_count); |
| |
| return min_t(int, ret, 0); |
| } |
| |
| static int igb_uc_unsync(struct net_device *netdev, const unsigned char *addr) |
| { |
| struct igb_adapter *adapter = netdev_priv(netdev); |
| |
| igb_del_mac_filter(adapter, addr, adapter->vfs_allocated_count); |
| |
| return 0; |
| } |
| |
| static int igb_set_vf_mac_filter(struct igb_adapter *adapter, const int vf, |
| const u32 info, const u8 *addr) |
| { |
| struct pci_dev *pdev = adapter->pdev; |
| struct vf_data_storage *vf_data = &adapter->vf_data[vf]; |
| struct vf_mac_filter *entry; |
| bool found = false; |
| int ret = 0; |
| |
| if ((vf_data->flags & IGB_VF_FLAG_PF_SET_MAC) && |
| !vf_data->trusted) { |
| dev_warn(&pdev->dev, |
| "VF %d requested MAC filter but is administratively denied\n", |
| vf); |
| return -EINVAL; |
| } |
| if (!is_valid_ether_addr(addr)) { |
| dev_warn(&pdev->dev, |
| "VF %d attempted to set invalid MAC filter\n", |
| vf); |
| return -EINVAL; |
| } |
| |
| switch (info) { |
| case E1000_VF_MAC_FILTER_CLR: |
| /* remove all unicast MAC filters related to the current VF */ |
| list_for_each_entry(entry, &adapter->vf_macs.l, l) { |
| if (entry->vf == vf) { |
| entry->vf = -1; |
| entry->free = true; |
| igb_del_mac_filter(adapter, entry->vf_mac, vf); |
| } |
| } |
| break; |
| case E1000_VF_MAC_FILTER_ADD: |
| /* try to find empty slot in the list */ |
| list_for_each_entry(entry, &adapter->vf_macs.l, l) { |
| if (entry->free) { |
| found = true; |
| break; |
| } |
| } |
| |
| if (found) { |
| entry->free = false; |
| entry->vf = vf; |
| ether_addr_copy(entry->vf_mac, addr); |
| |
| ret = igb_add_mac_filter(adapter, addr, vf); |
| ret = min_t(int, ret, 0); |
| } else { |
| ret = -ENOSPC; |
| } |
| |
| if (ret == -ENOSPC) |
| dev_warn(&pdev->dev, |
| "VF %d has requested MAC filter but there is no space for it\n", |
| vf); |
| break; |
| default: |
| ret = -EINVAL; |
| break; |
| } |
| |
| return ret; |
| } |
| |
| static int igb_set_vf_mac_addr(struct igb_adapter *adapter, u32 *msg, int vf) |
| { |
| struct pci_dev *pdev = adapter->pdev; |
| struct vf_data_storage *vf_data = &adapter->vf_data[vf]; |
| u32 info = msg[0] & E1000_VT_MSGINFO_MASK; |
| |
| /* The VF MAC Address is stored in a packed array of bytes |
| * starting at the second 32 bit word of the msg array |
| */ |
| unsigned char *addr = (unsigned char *)&msg[1]; |
| int ret = 0; |
| |
| if (!info) { |
| if ((vf_data->flags & IGB_VF_FLAG_PF_SET_MAC) && |
| !vf_data->trusted) { |
| dev_warn(&pdev->dev, |
| "VF %d attempted to override administratively set MAC address\nReload the VF driver to resume operations\n", |
| vf); |
| return -EINVAL; |
| } |
| |
| if (!is_valid_ether_addr(addr)) { |
| dev_warn(&pdev->dev, |
| "VF %d attempted to set invalid MAC\n", |
| vf); |
| return -EINVAL; |
| } |
| |
| ret = igb_set_vf_mac(adapter, vf, addr); |
| } else { |
| ret = igb_set_vf_mac_filter(adapter, vf, info, addr); |
| } |
| |
| return ret; |
| } |
| |
| static void igb_rcv_ack_from_vf(struct igb_adapter *adapter, u32 vf) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| struct vf_data_storage *vf_data = &adapter->vf_data[vf]; |
| u32 msg = E1000_VT_MSGTYPE_NACK; |
| |
| /* if device isn't clear to send it shouldn't be reading either */ |
| if (!(vf_data->flags & IGB_VF_FLAG_CTS) && |
| time_after(jiffies, vf_data->last_nack + (2 * HZ))) { |
| igb_write_mbx(hw, &msg, 1, vf); |
| vf_data->last_nack = jiffies; |
| } |
| } |
| |
| static void igb_rcv_msg_from_vf(struct igb_adapter *adapter, u32 vf) |
| { |
| struct pci_dev *pdev = adapter->pdev; |
| u32 msgbuf[E1000_VFMAILBOX_SIZE]; |
| struct e1000_hw *hw = &adapter->hw; |
| struct vf_data_storage *vf_data = &adapter->vf_data[vf]; |
| s32 retval; |
| |
| retval = igb_read_mbx(hw, msgbuf, E1000_VFMAILBOX_SIZE, vf, false); |
| |
| if (retval) { |
| /* if receive failed revoke VF CTS stats and restart init */ |
| dev_err(&pdev->dev, "Error receiving message from VF\n"); |
| vf_data->flags &= ~IGB_VF_FLAG_CTS; |
| if (!time_after(jiffies, vf_data->last_nack + (2 * HZ))) |
| goto unlock; |
| goto out; |
| } |
| |
| /* this is a message we already processed, do nothing */ |
| if (msgbuf[0] & (E1000_VT_MSGTYPE_ACK | E1000_VT_MSGTYPE_NACK)) |
| goto unlock; |
| |
| /* until the vf completes a reset it should not be |
| * allowed to start any configuration. |
| */ |
| if (msgbuf[0] == E1000_VF_RESET) { |
| /* unlocks mailbox */ |
| igb_vf_reset_msg(adapter, vf); |
| return; |
| } |
| |
| if (!(vf_data->flags & IGB_VF_FLAG_CTS)) { |
| if (!time_after(jiffies, vf_data->last_nack + (2 * HZ))) |
| goto unlock; |
| retval = -1; |
| goto out; |
| } |
| |
| switch ((msgbuf[0] & 0xFFFF)) { |
| case E1000_VF_SET_MAC_ADDR: |
| retval = igb_set_vf_mac_addr(adapter, msgbuf, vf); |
| break; |
| case E1000_VF_SET_PROMISC: |
| retval = igb_set_vf_promisc(adapter, msgbuf, vf); |
| break; |
| case E1000_VF_SET_MULTICAST: |
| retval = igb_set_vf_multicasts(adapter, msgbuf, vf); |
| break; |
| case E1000_VF_SET_LPE: |
| retval = igb_set_vf_rlpml(adapter, msgbuf[1], vf); |
| break; |
| case E1000_VF_SET_VLAN: |
| retval = -1; |
| if (vf_data->pf_vlan) |
| dev_warn(&pdev->dev, |
| "VF %d attempted to override administratively set VLAN tag\nReload the VF driver to resume operations\n", |
| vf); |
| else |
| retval = igb_set_vf_vlan_msg(adapter, msgbuf, vf); |
| break; |
| default: |
| dev_err(&pdev->dev, "Unhandled Msg %08x\n", msgbuf[0]); |
| retval = -1; |
| break; |
| } |
| |
| msgbuf[0] |= E1000_VT_MSGTYPE_CTS; |
| out: |
| /* notify the VF of the results of what it sent us */ |
| if (retval) |
| msgbuf[0] |= E1000_VT_MSGTYPE_NACK; |
| else |
| msgbuf[0] |= E1000_VT_MSGTYPE_ACK; |
| |
| /* unlocks mailbox */ |
| igb_write_mbx(hw, msgbuf, 1, vf); |
| return; |
| |
| unlock: |
| igb_unlock_mbx(hw, vf); |
| } |
| |
| static void igb_msg_task(struct igb_adapter *adapter) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| unsigned long flags; |
| u32 vf; |
| |
| spin_lock_irqsave(&adapter->vfs_lock, flags); |
| for (vf = 0; vf < adapter->vfs_allocated_count; vf++) { |
| /* process any reset requests */ |
| if (!igb_check_for_rst(hw, vf)) |
| igb_vf_reset_event(adapter, vf); |
| |
| /* process any messages pending */ |
| if (!igb_check_for_msg(hw, vf)) |
| igb_rcv_msg_from_vf(adapter, vf); |
| |
| /* process any acks */ |
| if (!igb_check_for_ack(hw, vf)) |
| igb_rcv_ack_from_vf(adapter, vf); |
| } |
| spin_unlock_irqrestore(&adapter->vfs_lock, flags); |
| } |
| |
| /** |
| * igb_set_uta - Set unicast filter table address |
| * @adapter: board private structure |
| * @set: boolean indicating if we are setting or clearing bits |
| * |
| * The unicast table address is a register array of 32-bit registers. |
| * The table is meant to be used in a way similar to how the MTA is used |
| * however due to certain limitations in the hardware it is necessary to |
| * set all the hash bits to 1 and use the VMOLR ROPE bit as a promiscuous |
| * enable bit to allow vlan tag stripping when promiscuous mode is enabled |
| **/ |
| static void igb_set_uta(struct igb_adapter *adapter, bool set) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| u32 uta = set ? ~0 : 0; |
| int i; |
| |
| /* we only need to do this if VMDq is enabled */ |
| if (!adapter->vfs_allocated_count) |
| return; |
| |
| for (i = hw->mac.uta_reg_count; i--;) |
| array_wr32(E1000_UTA, i, uta); |
| } |
| |
| /** |
| * igb_intr_msi - Interrupt Handler |
| * @irq: interrupt number |
| * @data: pointer to a network interface device structure |
| **/ |
| static irqreturn_t igb_intr_msi(int irq, void *data) |
| { |
| struct igb_adapter *adapter = data; |
| struct igb_q_vector *q_vector = adapter->q_vector[0]; |
| struct e1000_hw *hw = &adapter->hw; |
| /* read ICR disables interrupts using IAM */ |
| u32 icr = rd32(E1000_ICR); |
| |
| igb_write_itr(q_vector); |
| |
| if (icr & E1000_ICR_DRSTA) |
| schedule_work(&adapter->reset_task); |
| |
| if (icr & E1000_ICR_DOUTSYNC) { |
| /* HW is reporting DMA is out of sync */ |
| adapter->stats.doosync++; |
| } |
| |
| if (icr & (E1000_ICR_RXSEQ | E1000_ICR_LSC)) { |
| hw->mac.get_link_status = 1; |
| if (!test_bit(__IGB_DOWN, &adapter->state)) |
| mod_timer(&adapter->watchdog_timer, jiffies + 1); |
| } |
| |
| if (icr & E1000_ICR_TS) |
| igb_tsync_interrupt(adapter); |
| |
| napi_schedule(&q_vector->napi); |
| |
| return IRQ_HANDLED; |
| } |
| |
| /** |
| * igb_intr - Legacy Interrupt Handler |
| * @irq: interrupt number |
| * @data: pointer to a network interface device structure |
| **/ |
| static irqreturn_t igb_intr(int irq, void *data) |
| { |
| struct igb_adapter *adapter = data; |
| struct igb_q_vector *q_vector = adapter->q_vector[0]; |
| struct e1000_hw *hw = &adapter->hw; |
| /* Interrupt Auto-Mask...upon reading ICR, interrupts are masked. No |
| * need for the IMC write |
| */ |
| u32 icr = rd32(E1000_ICR); |
| |
| /* IMS will not auto-mask if INT_ASSERTED is not set, and if it is |
| * not set, then the adapter didn't send an interrupt |
| */ |
| if (!(icr & E1000_ICR_INT_ASSERTED)) |
| return IRQ_NONE; |
| |
| igb_write_itr(q_vector); |
| |
| if (icr & E1000_ICR_DRSTA) |
| schedule_work(&adapter->reset_task); |
| |
| if (icr & E1000_ICR_DOUTSYNC) { |
| /* HW is reporting DMA is out of sync */ |
| adapter->stats.doosync++; |
| } |
| |
| if (icr & (E1000_ICR_RXSEQ | E1000_ICR_LSC)) { |
| hw->mac.get_link_status = 1; |
| /* guard against interrupt when we're going down */ |
| if (!test_bit(__IGB_DOWN, &adapter->state)) |
| mod_timer(&adapter->watchdog_timer, jiffies + 1); |
| } |
| |
| if (icr & E1000_ICR_TS) |
| igb_tsync_interrupt(adapter); |
| |
| napi_schedule(&q_vector->napi); |
| |
| return IRQ_HANDLED; |
| } |
| |
| static void igb_ring_irq_enable(struct igb_q_vector *q_vector) |
| { |
| struct igb_adapter *adapter = q_vector->adapter; |
| struct e1000_hw *hw = &adapter->hw; |
| |
| if ((q_vector->rx.ring && (adapter->rx_itr_setting & 3)) || |
| (!q_vector->rx.ring && (adapter->tx_itr_setting & 3))) { |
| if ((adapter->num_q_vectors == 1) && !adapter->vf_data) |
| igb_set_itr(q_vector); |
| else |
| igb_update_ring_itr(q_vector); |
| } |
| |
| if (!test_bit(__IGB_DOWN, &adapter->state)) { |
| if (adapter->flags & IGB_FLAG_HAS_MSIX) |
| wr32(E1000_EIMS, q_vector->eims_value); |
| else |
| igb_irq_enable(adapter); |
| } |
| } |
| |
| /** |
| * igb_poll - NAPI Rx polling callback |
| * @napi: napi polling structure |
| * @budget: count of how many packets we should handle |
| **/ |
| static int igb_poll(struct napi_struct *napi, int budget) |
| { |
| struct igb_q_vector *q_vector = container_of(napi, |
| struct igb_q_vector, |
| napi); |
| bool clean_complete = true; |
| int work_done = 0; |
| |
| #ifdef CONFIG_IGB_DCA |
| if (q_vector->adapter->flags & IGB_FLAG_DCA_ENABLED) |
| igb_update_dca(q_vector); |
| #endif |
| if (q_vector->tx.ring) |
| clean_complete = igb_clean_tx_irq(q_vector, budget); |
| |
| if (q_vector->rx.ring) { |
| int cleaned = igb_clean_rx_irq(q_vector, budget); |
| |
| work_done += cleaned; |
| if (cleaned >= budget) |
| clean_complete = false; |
| } |
| |
| /* If all work not completed, return budget and keep polling */ |
| if (!clean_complete) |
| return budget; |
| |
| /* Exit the polling mode, but don't re-enable interrupts if stack might |
| * poll us due to busy-polling |
| */ |
| if (likely(napi_complete_done(napi, work_done))) |
| igb_ring_irq_enable(q_vector); |
| |
| return work_done; |
| } |
| |
| /** |
| * igb_clean_tx_irq - Reclaim resources after transmit completes |
| * @q_vector: pointer to q_vector containing needed info |
| * @napi_budget: Used to determine if we are in netpoll |
| * |
| * returns true if ring is completely cleaned |
| **/ |
| static bool igb_clean_tx_irq(struct igb_q_vector *q_vector, int napi_budget) |
| { |
| struct igb_adapter *adapter = q_vector->adapter; |
| struct igb_ring *tx_ring = q_vector->tx.ring; |
| struct igb_tx_buffer *tx_buffer; |
| union e1000_adv_tx_desc *tx_desc; |
| unsigned int total_bytes = 0, total_packets = 0; |
| unsigned int budget = q_vector->tx.work_limit; |
| unsigned int i = tx_ring->next_to_clean; |
| |
| if (test_bit(__IGB_DOWN, &adapter->state)) |
| return true; |
| |
| tx_buffer = &tx_ring->tx_buffer_info[i]; |
| tx_desc = IGB_TX_DESC(tx_ring, i); |
| i -= tx_ring->count; |
| |
| do { |
| union e1000_adv_tx_desc *eop_desc = tx_buffer->next_to_watch; |
| |
| /* if next_to_watch is not set then there is no work pending */ |
| if (!eop_desc) |
| break; |
| |
| /* prevent any other reads prior to eop_desc */ |
| smp_rmb(); |
| |
| /* if DD is not set pending work has not been completed */ |
| if (!(eop_desc->wb.status & cpu_to_le32(E1000_TXD_STAT_DD))) |
| break; |
| |
| /* clear next_to_watch to prevent false hangs */ |
| tx_buffer->next_to_watch = NULL; |
| |
| /* update the statistics for this packet */ |
| total_bytes += tx_buffer->bytecount; |
| total_packets += tx_buffer->gso_segs; |
| |
| /* free the skb */ |
| if (tx_buffer->type == IGB_TYPE_SKB) |
| napi_consume_skb(tx_buffer->skb, napi_budget); |
| else |
| xdp_return_frame(tx_buffer->xdpf); |
| |
| /* unmap skb header data */ |
| dma_unmap_single(tx_ring->dev, |
| dma_unmap_addr(tx_buffer, dma), |
| dma_unmap_len(tx_buffer, len), |
| DMA_TO_DEVICE); |
| |
| /* clear tx_buffer data */ |
| dma_unmap_len_set(tx_buffer, len, 0); |
| |
| /* clear last DMA location and unmap remaining buffers */ |
| while (tx_desc != eop_desc) { |
| tx_buffer++; |
| tx_desc++; |
| i++; |
| if (unlikely(!i)) { |
| i -= tx_ring->count; |
| tx_buffer = tx_ring->tx_buffer_info; |
| tx_desc = IGB_TX_DESC(tx_ring, 0); |
| } |
| |
| /* unmap any remaining paged data */ |
| if (dma_unmap_len(tx_buffer, len)) { |
| dma_unmap_page(tx_ring->dev, |
| dma_unmap_addr(tx_buffer, dma), |
| dma_unmap_len(tx_buffer, len), |
| DMA_TO_DEVICE); |
| dma_unmap_len_set(tx_buffer, len, 0); |
| } |
| } |
| |
| /* move us one more past the eop_desc for start of next pkt */ |
| tx_buffer++; |
| tx_desc++; |
| i++; |
| if (unlikely(!i)) { |
| i -= tx_ring->count; |
| tx_buffer = tx_ring->tx_buffer_info; |
| tx_desc = IGB_TX_DESC(tx_ring, 0); |
| } |
| |
| /* issue prefetch for next Tx descriptor */ |
| prefetch(tx_desc); |
| |
| /* update budget accounting */ |
| budget--; |
| } while (likely(budget)); |
| |
| netdev_tx_completed_queue(txring_txq(tx_ring), |
| total_packets, total_bytes); |
| i += tx_ring->count; |
| tx_ring->next_to_clean = i; |
| u64_stats_update_begin(&tx_ring->tx_syncp); |
| tx_ring->tx_stats.bytes += total_bytes; |
| tx_ring->tx_stats.packets += total_packets; |
| u64_stats_update_end(&tx_ring->tx_syncp); |
| q_vector->tx.total_bytes += total_bytes; |
| q_vector->tx.total_packets += total_packets; |
| |
| if (test_bit(IGB_RING_FLAG_TX_DETECT_HANG, &tx_ring->flags)) { |
| struct e1000_hw *hw = &adapter->hw; |
| |
| /* Detect a transmit hang in hardware, this serializes the |
| * check with the clearing of time_stamp and movement of i |
| */ |
| clear_bit(IGB_RING_FLAG_TX_DETECT_HANG, &tx_ring->flags); |
| if (tx_buffer->next_to_watch && |
| time_after(jiffies, tx_buffer->time_stamp + |
| (adapter->tx_timeout_factor * HZ)) && |
| !(rd32(E1000_STATUS) & E1000_STATUS_TXOFF)) { |
| |
| /* detected Tx unit hang */ |
| dev_err(tx_ring->dev, |
| "Detected Tx Unit Hang\n" |
| " Tx Queue <%d>\n" |
| " TDH <%x>\n" |
| " TDT <%x>\n" |
| " next_to_use <%x>\n" |
| " next_to_clean <%x>\n" |
| "buffer_info[next_to_clean]\n" |
| " time_stamp <%lx>\n" |
| " next_to_watch <%p>\n" |
| " jiffies <%lx>\n" |
| " desc.status <%x>\n", |
| tx_ring->queue_index, |
| rd32(E1000_TDH(tx_ring->reg_idx)), |
| readl(tx_ring->tail), |
| tx_ring->next_to_use, |
| tx_ring->next_to_clean, |
| tx_buffer->time_stamp, |
| tx_buffer->next_to_watch, |
| jiffies, |
| tx_buffer->next_to_watch->wb.status); |
| netif_stop_subqueue(tx_ring->netdev, |
| tx_ring->queue_index); |
| |
| /* we are about to reset, no point in enabling stuff */ |
| return true; |
| } |
| } |
| |
| #define TX_WAKE_THRESHOLD (DESC_NEEDED * 2) |
| if (unlikely(total_packets && |
| netif_carrier_ok(tx_ring->netdev) && |
| igb_desc_unused(tx_ring) >= TX_WAKE_THRESHOLD)) { |
| /* Make sure that anybody stopping the queue after this |
| * sees the new next_to_clean. |
| */ |
| smp_mb(); |
| if (__netif_subqueue_stopped(tx_ring->netdev, |
| tx_ring->queue_index) && |
| !(test_bit(__IGB_DOWN, &adapter->state))) { |
| netif_wake_subqueue(tx_ring->netdev, |
| tx_ring->queue_index); |
| |
| u64_stats_update_begin(&tx_ring->tx_syncp); |
| tx_ring->tx_stats.restart_queue++; |
| u64_stats_update_end(&tx_ring->tx_syncp); |
| } |
| } |
| |
| return !!budget; |
| } |
| |
| /** |
| * igb_reuse_rx_page - page flip buffer and store it back on the ring |
| * @rx_ring: rx descriptor ring to store buffers on |
| * @old_buff: donor buffer to have page reused |
| * |
| * Synchronizes page for reuse by the adapter |
| **/ |
| static void igb_reuse_rx_page(struct igb_ring *rx_ring, |
| struct igb_rx_buffer *old_buff) |
| { |
| struct igb_rx_buffer *new_buff; |
| u16 nta = rx_ring->next_to_alloc; |
| |
| new_buff = &rx_ring->rx_buffer_info[nta]; |
| |
| /* update, and store next to alloc */ |
| nta++; |
| rx_ring->next_to_alloc = (nta < rx_ring->count) ? nta : 0; |
| |
| /* Transfer page from old buffer to new buffer. |
| * Move each member individually to avoid possible store |
| * forwarding stalls. |
| */ |
| new_buff->dma = old_buff->dma; |
| new_buff->page = old_buff->page; |
| new_buff->page_offset = old_buff->page_offset; |
| new_buff->pagecnt_bias = old_buff->pagecnt_bias; |
| } |
| |
| static bool igb_can_reuse_rx_page(struct igb_rx_buffer *rx_buffer, |
| int rx_buf_pgcnt) |
| { |
| unsigned int pagecnt_bias = rx_buffer->pagecnt_bias; |
| struct page *page = rx_buffer->page; |
| |
| /* avoid re-using remote and pfmemalloc pages */ |
| if (!dev_page_is_reusable(page)) |
| return false; |
| |
| #if (PAGE_SIZE < 8192) |
| /* if we are only owner of page we can reuse it */ |
| if (unlikely((rx_buf_pgcnt - pagecnt_bias) > 1)) |
| return false; |
| #else |
| #define IGB_LAST_OFFSET \ |
| (SKB_WITH_OVERHEAD(PAGE_SIZE) - IGB_RXBUFFER_2048) |
| |
| if (rx_buffer->page_offset > IGB_LAST_OFFSET) |
| return false; |
| #endif |
| |
| /* If we have drained the page fragment pool we need to update |
| * the pagecnt_bias and page count so that we fully restock the |
| * number of references the driver holds. |
| */ |
| if (unlikely(pagecnt_bias == 1)) { |
| page_ref_add(page, USHRT_MAX - 1); |
| rx_buffer->pagecnt_bias = USHRT_MAX; |
| } |
| |
| return true; |
| } |
| |
| /** |
| * igb_add_rx_frag - Add contents of Rx buffer to sk_buff |
| * @rx_ring: rx descriptor ring to transact packets on |
| * @rx_buffer: buffer containing page to add |
| * @skb: sk_buff to place the data into |
| * @size: size of buffer to be added |
| * |
| * This function will add the data contained in rx_buffer->page to the skb. |
| **/ |
| static void igb_add_rx_frag(struct igb_ring *rx_ring, |
| struct igb_rx_buffer *rx_buffer, |
| struct sk_buff *skb, |
| unsigned int size) |
| { |
| #if (PAGE_SIZE < 8192) |
| unsigned int truesize = igb_rx_pg_size(rx_ring) / 2; |
| #else |
| unsigned int truesize = ring_uses_build_skb(rx_ring) ? |
| SKB_DATA_ALIGN(IGB_SKB_PAD + size) : |
| SKB_DATA_ALIGN(size); |
| #endif |
| skb_add_rx_frag(skb, skb_shinfo(skb)->nr_frags, rx_buffer->page, |
| rx_buffer->page_offset, size, truesize); |
| #if (PAGE_SIZE < 8192) |
| rx_buffer->page_offset ^= truesize; |
| #else |
| rx_buffer->page_offset += truesize; |
| #endif |
| } |
| |
| static struct sk_buff *igb_construct_skb(struct igb_ring *rx_ring, |
| struct igb_rx_buffer *rx_buffer, |
| struct xdp_buff *xdp, |
| ktime_t timestamp) |
| { |
| #if (PAGE_SIZE < 8192) |
| unsigned int truesize = igb_rx_pg_size(rx_ring) / 2; |
| #else |
| unsigned int truesize = SKB_DATA_ALIGN(xdp->data_end - |
| xdp->data_hard_start); |
| #endif |
| unsigned int size = xdp->data_end - xdp->data; |
| unsigned int headlen; |
| struct sk_buff *skb; |
| |
| /* prefetch first cache line of first page */ |
| net_prefetch(xdp->data); |
| |
| /* allocate a skb to store the frags */ |
| skb = napi_alloc_skb(&rx_ring->q_vector->napi, IGB_RX_HDR_LEN); |
| if (unlikely(!skb)) |
| return NULL; |
| |
| if (timestamp) |
| skb_hwtstamps(skb)->hwtstamp = timestamp; |
| |
| /* Determine available headroom for copy */ |
| headlen = size; |
| if (headlen > IGB_RX_HDR_LEN) |
| headlen = eth_get_headlen(skb->dev, xdp->data, IGB_RX_HDR_LEN); |
| |
| /* align pull length to size of long to optimize memcpy performance */ |
| memcpy(__skb_put(skb, headlen), xdp->data, ALIGN(headlen, sizeof(long))); |
| |
| /* update all of the pointers */ |
| size -= headlen; |
| if (size) { |
| skb_add_rx_frag(skb, 0, rx_buffer->page, |
| (xdp->data + headlen) - page_address(rx_buffer->page), |
| size, truesize); |
| #if (PAGE_SIZE < 8192) |
| rx_buffer->page_offset ^= truesize; |
| #else |
| rx_buffer->page_offset += truesize; |
| #endif |
| } else { |
| rx_buffer->pagecnt_bias++; |
| } |
| |
| return skb; |
| } |
| |
| static struct sk_buff *igb_build_skb(struct igb_ring *rx_ring, |
| struct igb_rx_buffer *rx_buffer, |
| struct xdp_buff *xdp, |
| ktime_t timestamp) |
| { |
| #if (PAGE_SIZE < 8192) |
| unsigned int truesize = igb_rx_pg_size(rx_ring) / 2; |
| #else |
| unsigned int truesize = SKB_DATA_ALIGN(sizeof(struct skb_shared_info)) + |
| SKB_DATA_ALIGN(xdp->data_end - |
| xdp->data_hard_start); |
| #endif |
| unsigned int metasize = xdp->data - xdp->data_meta; |
| struct sk_buff *skb; |
| |
| /* prefetch first cache line of first page */ |
| net_prefetch(xdp->data_meta); |
| |
| /* build an skb around the page buffer */ |
| skb = napi_build_skb(xdp->data_hard_start, truesize); |
| if (unlikely(!skb)) |
| return NULL; |
| |
| /* update pointers within the skb to store the data */ |
| skb_reserve(skb, xdp->data - xdp->data_hard_start); |
| __skb_put(skb, xdp->data_end - xdp->data); |
| |
| if (metasize) |
| skb_metadata_set(skb, metasize); |
| |
| if (timestamp) |
| skb_hwtstamps(skb)->hwtstamp = timestamp; |
| |
| /* update buffer offset */ |
| #if (PAGE_SIZE < 8192) |
| rx_buffer->page_offset ^= truesize; |
| #else |
| rx_buffer->page_offset += truesize; |
| #endif |
| |
| return skb; |
| } |
| |
| static struct sk_buff *igb_run_xdp(struct igb_adapter *adapter, |
| struct igb_ring *rx_ring, |
| struct xdp_buff *xdp) |
| { |
| int err, result = IGB_XDP_PASS; |
| struct bpf_prog *xdp_prog; |
| u32 act; |
| |
| xdp_prog = READ_ONCE(rx_ring->xdp_prog); |
| |
| if (!xdp_prog) |
| goto xdp_out; |
| |
| prefetchw(xdp->data_hard_start); /* xdp_frame write */ |
| |
| act = bpf_prog_run_xdp(xdp_prog, xdp); |
| switch (act) { |
| case XDP_PASS: |
| break; |
| case XDP_TX: |
| result = igb_xdp_xmit_back(adapter, xdp); |
| if (result == IGB_XDP_CONSUMED) |
| goto out_failure; |
| break; |
| case XDP_REDIRECT: |
| err = xdp_do_redirect(adapter->netdev, xdp, xdp_prog); |
| if (err) |
| goto out_failure; |
| result = IGB_XDP_REDIR; |
| break; |
| default: |
| bpf_warn_invalid_xdp_action(adapter->netdev, xdp_prog, act); |
| fallthrough; |
| case XDP_ABORTED: |
| out_failure: |
| trace_xdp_exception(rx_ring->netdev, xdp_prog, act); |
| fallthrough; |
| case XDP_DROP: |
| result = IGB_XDP_CONSUMED; |
| break; |
| } |
| xdp_out: |
| return ERR_PTR(-result); |
| } |
| |
| static unsigned int igb_rx_frame_truesize(struct igb_ring *rx_ring, |
| unsigned int size) |
| { |
| unsigned int truesize; |
| |
| #if (PAGE_SIZE < 8192) |
| truesize = igb_rx_pg_size(rx_ring) / 2; /* Must be power-of-2 */ |
| #else |
| truesize = ring_uses_build_skb(rx_ring) ? |
| SKB_DATA_ALIGN(IGB_SKB_PAD + size) + |
| SKB_DATA_ALIGN(sizeof(struct skb_shared_info)) : |
| SKB_DATA_ALIGN(size); |
| #endif |
| return truesize; |
| } |
| |
| static void igb_rx_buffer_flip(struct igb_ring *rx_ring, |
| struct igb_rx_buffer *rx_buffer, |
| unsigned int size) |
| { |
| unsigned int truesize = igb_rx_frame_truesize(rx_ring, size); |
| #if (PAGE_SIZE < 8192) |
| rx_buffer->page_offset ^= truesize; |
| #else |
| rx_buffer->page_offset += truesize; |
| #endif |
| } |
| |
| static inline void igb_rx_checksum(struct igb_ring *ring, |
| union e1000_adv_rx_desc *rx_desc, |
| struct sk_buff *skb) |
| { |
| skb_checksum_none_assert(skb); |
| |
| /* Ignore Checksum bit is set */ |
| if (igb_test_staterr(rx_desc, E1000_RXD_STAT_IXSM)) |
| return; |
| |
| /* Rx checksum disabled via ethtool */ |
| if (!(ring->netdev->features & NETIF_F_RXCSUM)) |
| return; |
| |
| /* TCP/UDP checksum error bit is set */ |
| if (igb_test_staterr(rx_desc, |
| E1000_RXDEXT_STATERR_TCPE | |
| E1000_RXDEXT_STATERR_IPE)) { |
| /* work around errata with sctp packets where the TCPE aka |
| * L4E bit is set incorrectly on 64 byte (60 byte w/o crc) |
| * packets, (aka let the stack check the crc32c) |
| */ |
| if (!((skb->len == 60) && |
| test_bit(IGB_RING_FLAG_RX_SCTP_CSUM, &ring->flags))) { |
| u64_stats_update_begin(&ring->rx_syncp); |
| ring->rx_stats.csum_err++; |
| u64_stats_update_end(&ring->rx_syncp); |
| } |
| /* let the stack verify checksum errors */ |
| return; |
| } |
| /* It must be a TCP or UDP packet with a valid checksum */ |
| if (igb_test_staterr(rx_desc, E1000_RXD_STAT_TCPCS | |
| E1000_RXD_STAT_UDPCS)) |
| skb->ip_summed = CHECKSUM_UNNECESSARY; |
| |
| dev_dbg(ring->dev, "cksum success: bits %08X\n", |
| le32_to_cpu(rx_desc->wb.upper.status_error)); |
| } |
| |
| static inline void igb_rx_hash(struct igb_ring *ring, |
| union e1000_adv_rx_desc *rx_desc, |
| struct sk_buff *skb) |
| { |
| if (ring->netdev->features & NETIF_F_RXHASH) |
| skb_set_hash(skb, |
| le32_to_cpu(rx_desc->wb.lower.hi_dword.rss), |
| PKT_HASH_TYPE_L3); |
| } |
| |
| /** |
| * igb_is_non_eop - process handling of non-EOP buffers |
| * @rx_ring: Rx ring being processed |
| * @rx_desc: Rx descriptor for current buffer |
| * |
| * This function updates next to clean. If the buffer is an EOP buffer |
| * this function exits returning false, otherwise it will place the |
| * sk_buff in the next buffer to be chained and return true indicating |
| * that this is in fact a non-EOP buffer. |
| **/ |
| static bool igb_is_non_eop(struct igb_ring *rx_ring, |
| union e1000_adv_rx_desc *rx_desc) |
| { |
| u32 ntc = rx_ring->next_to_clean + 1; |
| |
| /* fetch, update, and store next to clean */ |
| ntc = (ntc < rx_ring->count) ? ntc : 0; |
| rx_ring->next_to_clean = ntc; |
| |
| prefetch(IGB_RX_DESC(rx_ring, ntc)); |
| |
| if (likely(igb_test_staterr(rx_desc, E1000_RXD_STAT_EOP))) |
| return false; |
| |
| return true; |
| } |
| |
| /** |
| * igb_cleanup_headers - Correct corrupted or empty headers |
| * @rx_ring: rx descriptor ring packet is being transacted on |
| * @rx_desc: pointer to the EOP Rx descriptor |
| * @skb: pointer to current skb being fixed |
| * |
| * Address the case where we are pulling data in on pages only |
| * and as such no data is present in the skb header. |
| * |
| * In addition if skb is not at least 60 bytes we need to pad it so that |
| * it is large enough to qualify as a valid Ethernet frame. |
| * |
| * Returns true if an error was encountered and skb was freed. |
| **/ |
| static bool igb_cleanup_headers(struct igb_ring *rx_ring, |
| union e1000_adv_rx_desc *rx_desc, |
| struct sk_buff *skb) |
| { |
| /* XDP packets use error pointer so abort at this point */ |
| if (IS_ERR(skb)) |
| return true; |
| |
| if (unlikely((igb_test_staterr(rx_desc, |
| E1000_RXDEXT_ERR_FRAME_ERR_MASK)))) { |
| struct net_device *netdev = rx_ring->netdev; |
| if (!(netdev->features & NETIF_F_RXALL)) { |
| dev_kfree_skb_any(skb); |
| return true; |
| } |
| } |
| |
| /* if eth_skb_pad returns an error the skb was freed */ |
| if (eth_skb_pad(skb)) |
| return true; |
| |
| return false; |
| } |
| |
| /** |
| * igb_process_skb_fields - Populate skb header fields from Rx descriptor |
| * @rx_ring: rx descriptor ring packet is being transacted on |
| * @rx_desc: pointer to the EOP Rx descriptor |
| * @skb: pointer to current skb being populated |
| * |
| * This function checks the ring, descriptor, and packet information in |
| * order to populate the hash, checksum, VLAN, timestamp, protocol, and |
| * other fields within the skb. |
| **/ |
| static void igb_process_skb_fields(struct igb_ring *rx_ring, |
| union e1000_adv_rx_desc *rx_desc, |
| struct sk_buff *skb) |
| { |
| struct net_device *dev = rx_ring->netdev; |
| |
| igb_rx_hash(rx_ring, rx_desc, skb); |
| |
| igb_rx_checksum(rx_ring, rx_desc, skb); |
| |
| if (igb_test_staterr(rx_desc, E1000_RXDADV_STAT_TS) && |
| !igb_test_staterr(rx_desc, E1000_RXDADV_STAT_TSIP)) |
| igb_ptp_rx_rgtstamp(rx_ring->q_vector, skb); |
| |
| if ((dev->features & NETIF_F_HW_VLAN_CTAG_RX) && |
| igb_test_staterr(rx_desc, E1000_RXD_STAT_VP)) { |
| u16 vid; |
| |
| if (igb_test_staterr(rx_desc, E1000_RXDEXT_STATERR_LB) && |
| test_bit(IGB_RING_FLAG_RX_LB_VLAN_BSWAP, &rx_ring->flags)) |
| vid = be16_to_cpu((__force __be16)rx_desc->wb.upper.vlan); |
| else |
| vid = le16_to_cpu(rx_desc->wb.upper.vlan); |
| |
| __vlan_hwaccel_put_tag(skb, htons(ETH_P_8021Q), vid); |
| } |
| |
| skb_record_rx_queue(skb, rx_ring->queue_index); |
| |
| skb->protocol = eth_type_trans(skb, rx_ring->netdev); |
| } |
| |
| static unsigned int igb_rx_offset(struct igb_ring *rx_ring) |
| { |
| return ring_uses_build_skb(rx_ring) ? IGB_SKB_PAD : 0; |
| } |
| |
| static struct igb_rx_buffer *igb_get_rx_buffer(struct igb_ring *rx_ring, |
| const unsigned int size, int *rx_buf_pgcnt) |
| { |
| struct igb_rx_buffer *rx_buffer; |
| |
| rx_buffer = &rx_ring->rx_buffer_info[rx_ring->next_to_clean]; |
| *rx_buf_pgcnt = |
| #if (PAGE_SIZE < 8192) |
| page_count(rx_buffer->page); |
| #else |
| 0; |
| #endif |
| prefetchw(rx_buffer->page); |
| |
| /* we are reusing so sync this buffer for CPU use */ |
| dma_sync_single_range_for_cpu(rx_ring->dev, |
| rx_buffer->dma, |
| rx_buffer->page_offset, |
| size, |
| DMA_FROM_DEVICE); |
| |
| rx_buffer->pagecnt_bias--; |
| |
| return rx_buffer; |
| } |
| |
| static void igb_put_rx_buffer(struct igb_ring *rx_ring, |
| struct igb_rx_buffer *rx_buffer, int rx_buf_pgcnt) |
| { |
| if (igb_can_reuse_rx_page(rx_buffer, rx_buf_pgcnt)) { |
| /* hand second half of page back to the ring */ |
| igb_reuse_rx_page(rx_ring, rx_buffer); |
| } else { |
| /* We are not reusing the buffer so unmap it and free |
| * any references we are holding to it |
| */ |
| dma_unmap_page_attrs(rx_ring->dev, rx_buffer->dma, |
| igb_rx_pg_size(rx_ring), DMA_FROM_DEVICE, |
| IGB_RX_DMA_ATTR); |
| __page_frag_cache_drain(rx_buffer->page, |
| rx_buffer->pagecnt_bias); |
| } |
| |
| /* clear contents of rx_buffer */ |
| rx_buffer->page = NULL; |
| } |
| |
| static int igb_clean_rx_irq(struct igb_q_vector *q_vector, const int budget) |
| { |
| struct igb_adapter *adapter = q_vector->adapter; |
| struct igb_ring *rx_ring = q_vector->rx.ring; |
| struct sk_buff *skb = rx_ring->skb; |
| unsigned int total_bytes = 0, total_packets = 0; |
| u16 cleaned_count = igb_desc_unused(rx_ring); |
| unsigned int xdp_xmit = 0; |
| struct xdp_buff xdp; |
| u32 frame_sz = 0; |
| int rx_buf_pgcnt; |
| |
| /* Frame size depend on rx_ring setup when PAGE_SIZE=4K */ |
| #if (PAGE_SIZE < 8192) |
| frame_sz = igb_rx_frame_truesize(rx_ring, 0); |
| #endif |
| xdp_init_buff(&xdp, frame_sz, &rx_ring->xdp_rxq); |
| |
| while (likely(total_packets < budget)) { |
| union e1000_adv_rx_desc *rx_desc; |
| struct igb_rx_buffer *rx_buffer; |
| ktime_t timestamp = 0; |
| int pkt_offset = 0; |
| unsigned int size; |
| void *pktbuf; |
| |
| /* return some buffers to hardware, one at a time is too slow */ |
| if (cleaned_count >= IGB_RX_BUFFER_WRITE) { |
| igb_alloc_rx_buffers(rx_ring, cleaned_count); |
| cleaned_count = 0; |
| } |
| |
| rx_desc = IGB_RX_DESC(rx_ring, rx_ring->next_to_clean); |
| size = le16_to_cpu(rx_desc->wb.upper.length); |
| if (!size) |
| break; |
| |
| /* This memory barrier is needed to keep us from reading |
| * any other fields out of the rx_desc until we know the |
| * descriptor has been written back |
| */ |
| dma_rmb(); |
| |
| rx_buffer = igb_get_rx_buffer(rx_ring, size, &rx_buf_pgcnt); |
| pktbuf = page_address(rx_buffer->page) + rx_buffer->page_offset; |
| |
| /* pull rx packet timestamp if available and valid */ |
| if (igb_test_staterr(rx_desc, E1000_RXDADV_STAT_TSIP)) { |
| int ts_hdr_len; |
| |
| ts_hdr_len = igb_ptp_rx_pktstamp(rx_ring->q_vector, |
| pktbuf, ×tamp); |
| |
| pkt_offset += ts_hdr_len; |
| size -= ts_hdr_len; |
| } |
| |
| /* retrieve a buffer from the ring */ |
| if (!skb) { |
| unsigned char *hard_start = pktbuf - igb_rx_offset(rx_ring); |
| unsigned int offset = pkt_offset + igb_rx_offset(rx_ring); |
| |
| xdp_prepare_buff(&xdp, hard_start, offset, size, true); |
| xdp_buff_clear_frags_flag(&xdp); |
| #if (PAGE_SIZE > 4096) |
| /* At larger PAGE_SIZE, frame_sz depend on len size */ |
| xdp.frame_sz = igb_rx_frame_truesize(rx_ring, size); |
| #endif |
| skb = igb_run_xdp(adapter, rx_ring, &xdp); |
| } |
| |
| if (IS_ERR(skb)) { |
| unsigned int xdp_res = -PTR_ERR(skb); |
| |
| if (xdp_res & (IGB_XDP_TX | IGB_XDP_REDIR)) { |
| xdp_xmit |= xdp_res; |
| igb_rx_buffer_flip(rx_ring, rx_buffer, size); |
| } else { |
| rx_buffer->pagecnt_bias++; |
| } |
| total_packets++; |
| total_bytes += size; |
| } else if (skb) |
| igb_add_rx_frag(rx_ring, rx_buffer, skb, size); |
| else if (ring_uses_build_skb(rx_ring)) |
| skb = igb_build_skb(rx_ring, rx_buffer, &xdp, |
| timestamp); |
| else |
| skb = igb_construct_skb(rx_ring, rx_buffer, |
| &xdp, timestamp); |
| |
| /* exit if we failed to retrieve a buffer */ |
| if (!skb) { |
| rx_ring->rx_stats.alloc_failed++; |
| rx_buffer->pagecnt_bias++; |
| break; |
| } |
| |
| igb_put_rx_buffer(rx_ring, rx_buffer, rx_buf_pgcnt); |
| cleaned_count++; |
| |
| /* fetch next buffer in frame if non-eop */ |
| if (igb_is_non_eop(rx_ring, rx_desc)) |
| continue; |
| |
| /* verify the packet layout is correct */ |
| if (igb_cleanup_headers(rx_ring, rx_desc, skb)) { |
| skb = NULL; |
| continue; |
| } |
| |
| /* probably a little skewed due to removing CRC */ |
| total_bytes += skb->len; |
| |
| /* populate checksum, timestamp, VLAN, and protocol */ |
| igb_process_skb_fields(rx_ring, rx_desc, skb); |
| |
| napi_gro_receive(&q_vector->napi, skb); |
| |
| /* reset skb pointer */ |
| skb = NULL; |
| |
| /* update budget accounting */ |
| total_packets++; |
| } |
| |
| /* place incomplete frames back on ring for completion */ |
| rx_ring->skb = skb; |
| |
| if (xdp_xmit & IGB_XDP_REDIR) |
| xdp_do_flush(); |
| |
| if (xdp_xmit & IGB_XDP_TX) { |
| struct igb_ring *tx_ring = igb_xdp_tx_queue_mapping(adapter); |
| |
| igb_xdp_ring_update_tail(tx_ring); |
| } |
| |
| u64_stats_update_begin(&rx_ring->rx_syncp); |
| rx_ring->rx_stats.packets += total_packets; |
| rx_ring->rx_stats.bytes += total_bytes; |
| u64_stats_update_end(&rx_ring->rx_syncp); |
| q_vector->rx.total_packets += total_packets; |
| q_vector->rx.total_bytes += total_bytes; |
| |
| if (cleaned_count) |
| igb_alloc_rx_buffers(rx_ring, cleaned_count); |
| |
| return total_packets; |
| } |
| |
| static bool igb_alloc_mapped_page(struct igb_ring *rx_ring, |
| struct igb_rx_buffer *bi) |
| { |
| struct page *page = bi->page; |
| dma_addr_t dma; |
| |
| /* since we are recycling buffers we should seldom need to alloc */ |
| if (likely(page)) |
| return true; |
| |
| /* alloc new page for storage */ |
| page = dev_alloc_pages(igb_rx_pg_order(rx_ring)); |
| if (unlikely(!page)) { |
| rx_ring->rx_stats.alloc_failed++; |
| return false; |
| } |
| |
| /* map page for use */ |
| dma = dma_map_page_attrs(rx_ring->dev, page, 0, |
| igb_rx_pg_size(rx_ring), |
| DMA_FROM_DEVICE, |
| IGB_RX_DMA_ATTR); |
| |
| /* if mapping failed free memory back to system since |
| * there isn't much point in holding memory we can't use |
| */ |
| if (dma_mapping_error(rx_ring->dev, dma)) { |
| __free_pages(page, igb_rx_pg_order(rx_ring)); |
| |
| rx_ring->rx_stats.alloc_failed++; |
| return false; |
| } |
| |
| bi->dma = dma; |
| bi->page = page; |
| bi->page_offset = igb_rx_offset(rx_ring); |
| page_ref_add(page, USHRT_MAX - 1); |
| bi->pagecnt_bias = USHRT_MAX; |
| |
| return true; |
| } |
| |
| /** |
| * igb_alloc_rx_buffers - Replace used receive buffers |
| * @rx_ring: rx descriptor ring to allocate new receive buffers |
| * @cleaned_count: count of buffers to allocate |
| **/ |
| void igb_alloc_rx_buffers(struct igb_ring *rx_ring, u16 cleaned_count) |
| { |
| union e1000_adv_rx_desc *rx_desc; |
| struct igb_rx_buffer *bi; |
| u16 i = rx_ring->next_to_use; |
| u16 bufsz; |
| |
| /* nothing to do */ |
| if (!cleaned_count) |
| return; |
| |
| rx_desc = IGB_RX_DESC(rx_ring, i); |
| bi = &rx_ring->rx_buffer_info[i]; |
| i -= rx_ring->count; |
| |
| bufsz = igb_rx_bufsz(rx_ring); |
| |
| do { |
| if (!igb_alloc_mapped_page(rx_ring, bi)) |
| break; |
| |
| /* sync the buffer for use by the device */ |
| dma_sync_single_range_for_device(rx_ring->dev, bi->dma, |
| bi->page_offset, bufsz, |
| DMA_FROM_DEVICE); |
| |
| /* Refresh the desc even if buffer_addrs didn't change |
| * because each write-back erases this info. |
| */ |
| rx_desc->read.pkt_addr = cpu_to_le64(bi->dma + bi->page_offset); |
| |
| rx_desc++; |
| bi++; |
| i++; |
| if (unlikely(!i)) { |
| rx_desc = IGB_RX_DESC(rx_ring, 0); |
| bi = rx_ring->rx_buffer_info; |
| i -= rx_ring->count; |
| } |
| |
| /* clear the length for the next_to_use descriptor */ |
| rx_desc->wb.upper.length = 0; |
| |
| cleaned_count--; |
| } while (cleaned_count); |
| |
| i += rx_ring->count; |
| |
| if (rx_ring->next_to_use != i) { |
| /* record the next descriptor to use */ |
| rx_ring->next_to_use = i; |
| |
| /* update next to alloc since we have filled the ring */ |
| rx_ring->next_to_alloc = i; |
| |
| /* Force memory writes to complete before letting h/w |
| * know there are new descriptors to fetch. (Only |
| * applicable for weak-ordered memory model archs, |
| * such as IA-64). |
| */ |
| dma_wmb(); |
| writel(i, rx_ring->tail); |
| } |
| } |
| |
| /** |
| * igb_mii_ioctl - |
| * @netdev: pointer to netdev struct |
| * @ifr: interface structure |
| * @cmd: ioctl command to execute |
| **/ |
| static int igb_mii_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd) |
| { |
| struct igb_adapter *adapter = netdev_priv(netdev); |
| struct mii_ioctl_data *data = if_mii(ifr); |
| |
| if (adapter->hw.phy.media_type != e1000_media_type_copper) |
| return -EOPNOTSUPP; |
| |
| switch (cmd) { |
| case SIOCGMIIPHY: |
| data->phy_id = adapter->hw.phy.addr; |
| break; |
| case SIOCGMIIREG: |
| if (igb_read_phy_reg(&adapter->hw, data->reg_num & 0x1F, |
| &data->val_out)) |
| return -EIO; |
| break; |
| case SIOCSMIIREG: |
| if (igb_write_phy_reg(&adapter->hw, data->reg_num & 0x1F, |
| data->val_in)) |
| return -EIO; |
| break; |
| default: |
| return -EOPNOTSUPP; |
| } |
| return 0; |
| } |
| |
| /** |
| * igb_ioctl - |
| * @netdev: pointer to netdev struct |
| * @ifr: interface structure |
| * @cmd: ioctl command to execute |
| **/ |
| static int igb_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd) |
| { |
| switch (cmd) { |
| case SIOCGMIIPHY: |
| case SIOCGMIIREG: |
| case SIOCSMIIREG: |
| return igb_mii_ioctl(netdev, ifr, cmd); |
| case SIOCGHWTSTAMP: |
| return igb_ptp_get_ts_config(netdev, ifr); |
| case SIOCSHWTSTAMP: |
| return igb_ptp_set_ts_config(netdev, ifr); |
| default: |
| return -EOPNOTSUPP; |
| } |
| } |
| |
| void igb_read_pci_cfg(struct e1000_hw *hw, u32 reg, u16 *value) |
| { |
| struct igb_adapter *adapter = hw->back; |
| |
| pci_read_config_word(adapter->pdev, reg, value); |
| } |
| |
| void igb_write_pci_cfg(struct e1000_hw *hw, u32 reg, u16 *value) |
| { |
| struct igb_adapter *adapter = hw->back; |
| |
| pci_write_config_word(adapter->pdev, reg, *value); |
| } |
| |
| s32 igb_read_pcie_cap_reg(struct e1000_hw *hw, u32 reg, u16 *value) |
| { |
| struct igb_adapter *adapter = hw->back; |
| |
| if (pcie_capability_read_word(adapter->pdev, reg, value)) |
| return -E1000_ERR_CONFIG; |
| |
| return 0; |
| } |
| |
| s32 igb_write_pcie_cap_reg(struct e1000_hw *hw, u32 reg, u16 *value) |
| { |
| struct igb_adapter *adapter = hw->back; |
| |
| if (pcie_capability_write_word(adapter->pdev, reg, *value)) |
| return -E1000_ERR_CONFIG; |
| |
| return 0; |
| } |
| |
| static void igb_vlan_mode(struct net_device *netdev, netdev_features_t features) |
| { |
| struct igb_adapter *adapter = netdev_priv(netdev); |
| struct e1000_hw *hw = &adapter->hw; |
| u32 ctrl, rctl; |
| bool enable = !!(features & NETIF_F_HW_VLAN_CTAG_RX); |
| |
| if (enable) { |
| /* enable VLAN tag insert/strip */ |
| ctrl = rd32(E1000_CTRL); |
| ctrl |= E1000_CTRL_VME; |
| wr32(E1000_CTRL, ctrl); |
| |
| /* Disable CFI check */ |
| rctl = rd32(E1000_RCTL); |
| rctl &= ~E1000_RCTL_CFIEN; |
| wr32(E1000_RCTL, rctl); |
| } else { |
| /* disable VLAN tag insert/strip */ |
| ctrl = rd32(E1000_CTRL); |
| ctrl &= ~E1000_CTRL_VME; |
| wr32(E1000_CTRL, ctrl); |
| } |
| |
| igb_set_vf_vlan_strip(adapter, adapter->vfs_allocated_count, enable); |
| } |
| |
| static int igb_vlan_rx_add_vid(struct net_device *netdev, |
| __be16 proto, u16 vid) |
| { |
| struct igb_adapter *adapter = netdev_priv(netdev); |
| struct e1000_hw *hw = &adapter->hw; |
| int pf_id = adapter->vfs_allocated_count; |
| |
| /* add the filter since PF can receive vlans w/o entry in vlvf */ |
| if (!vid || !(adapter->flags & IGB_FLAG_VLAN_PROMISC)) |
| igb_vfta_set(hw, vid, pf_id, true, !!vid); |
| |
| set_bit(vid, adapter->active_vlans); |
| |
| return 0; |
| } |
| |
| static int igb_vlan_rx_kill_vid(struct net_device *netdev, |
| __be16 proto, u16 vid) |
| { |
| struct igb_adapter *adapter = netdev_priv(netdev); |
| int pf_id = adapter->vfs_allocated_count; |
| struct e1000_hw *hw = &adapter->hw; |
| |
| /* remove VID from filter table */ |
| if (vid && !(adapter->flags & IGB_FLAG_VLAN_PROMISC)) |
| igb_vfta_set(hw, vid, pf_id, false, true); |
| |
| clear_bit(vid, adapter->active_vlans); |
| |
| return 0; |
| } |
| |
| static void igb_restore_vlan(struct igb_adapter *adapter) |
| { |
| u16 vid = 1; |
| |
| igb_vlan_mode(adapter->netdev, adapter->netdev->features); |
| igb_vlan_rx_add_vid(adapter->netdev, htons(ETH_P_8021Q), 0); |
| |
| for_each_set_bit_from(vid, adapter->active_vlans, VLAN_N_VID) |
| igb_vlan_rx_add_vid(adapter->netdev, htons(ETH_P_8021Q), vid); |
| } |
| |
| int igb_set_spd_dplx(struct igb_adapter *adapter, u32 spd, u8 dplx) |
| { |
| struct pci_dev *pdev = adapter->pdev; |
| struct e1000_mac_info *mac = &adapter->hw.mac; |
| |
| mac->autoneg = 0; |
| |
| /* Make sure dplx is at most 1 bit and lsb of speed is not set |
| * for the switch() below to work |
| */ |
| if ((spd & 1) || (dplx & ~1)) |
| goto err_inval; |
| |
| /* Fiber NIC's only allow 1000 gbps Full duplex |
| * and 100Mbps Full duplex for 100baseFx sfp |
| */ |
| if (adapter->hw.phy.media_type == e1000_media_type_internal_serdes) { |
| switch (spd + dplx) { |
| case SPEED_10 + DUPLEX_HALF: |
| case SPEED_10 + DUPLEX_FULL: |
| case SPEED_100 + DUPLEX_HALF: |
| goto err_inval; |
| default: |
| break; |
| } |
| } |
| |
| switch (spd + dplx) { |
| case SPEED_10 + DUPLEX_HALF: |
| mac->forced_speed_duplex = ADVERTISE_10_HALF; |
| break; |
| case SPEED_10 + DUPLEX_FULL: |
| mac->forced_speed_duplex = ADVERTISE_10_FULL; |
| break; |
| case SPEED_100 + DUPLEX_HALF: |
| mac->forced_speed_duplex = ADVERTISE_100_HALF; |
| break; |
| case SPEED_100 + DUPLEX_FULL: |
| mac->forced_speed_duplex = ADVERTISE_100_FULL; |
| break; |
| case SPEED_1000 + DUPLEX_FULL: |
| mac->autoneg = 1; |
| adapter->hw.phy.autoneg_advertised = ADVERTISE_1000_FULL; |
| break; |
| case SPEED_1000 + DUPLEX_HALF: /* not supported */ |
| default: |
| goto err_inval; |
| } |
| |
| /* clear MDI, MDI(-X) override is only allowed when autoneg enabled */ |
| adapter->hw.phy.mdix = AUTO_ALL_MODES; |
| |
| return 0; |
| |
| err_inval: |
| dev_err(&pdev->dev, "Unsupported Speed/Duplex configuration\n"); |
| return -EINVAL; |
| } |
| |
| static int __igb_shutdown(struct pci_dev *pdev, bool *enable_wake, |
| bool runtime) |
| { |
| struct net_device *netdev = pci_get_drvdata(pdev); |
| struct igb_adapter *adapter = netdev_priv(netdev); |
| struct e1000_hw *hw = &adapter->hw; |
| u32 ctrl, rctl, status; |
| u32 wufc = runtime ? E1000_WUFC_LNKC : adapter->wol; |
| bool wake; |
| |
| rtnl_lock(); |
| netif_device_detach(netdev); |
| |
| if (netif_running(netdev)) |
| __igb_close(netdev, true); |
| |
| igb_ptp_suspend(adapter); |
| |
| igb_clear_interrupt_scheme(adapter); |
| rtnl_unlock(); |
| |
| status = rd32(E1000_STATUS); |
| if (status & E1000_STATUS_LU) |
| wufc &= ~E1000_WUFC_LNKC; |
| |
| if (wufc) { |
| igb_setup_rctl(adapter); |
| igb_set_rx_mode(netdev); |
| |
| /* turn on all-multi mode if wake on multicast is enabled */ |
| if (wufc & E1000_WUFC_MC) { |
| rctl = rd32(E1000_RCTL); |
| rctl |= E1000_RCTL_MPE; |
| wr32(E1000_RCTL, rctl); |
| } |
| |
| ctrl = rd32(E1000_CTRL); |
| ctrl |= E1000_CTRL_ADVD3WUC; |
| wr32(E1000_CTRL, ctrl); |
| |
| /* Allow time for pending master requests to run */ |
| igb_disable_pcie_master(hw); |
| |
| wr32(E1000_WUC, E1000_WUC_PME_EN); |
| wr32(E1000_WUFC, wufc); |
| } else { |
| wr32(E1000_WUC, 0); |
| wr32(E1000_WUFC, 0); |
| } |
| |
| wake = wufc || adapter->en_mng_pt; |
| if (!wake) |
| igb_power_down_link(adapter); |
| else |
| igb_power_up_link(adapter); |
| |
| if (enable_wake) |
| *enable_wake = wake; |
| |
| /* Release control of h/w to f/w. If f/w is AMT enabled, this |
| * would have already happened in close and is redundant. |
| */ |
| igb_release_hw_control(adapter); |
| |
| pci_disable_device(pdev); |
| |
| return 0; |
| } |
| |
| static void igb_deliver_wake_packet(struct net_device *netdev) |
| { |
| struct igb_adapter *adapter = netdev_priv(netdev); |
| struct e1000_hw *hw = &adapter->hw; |
| struct sk_buff *skb; |
| u32 wupl; |
| |
| wupl = rd32(E1000_WUPL) & E1000_WUPL_MASK; |
| |
| /* WUPM stores only the first 128 bytes of the wake packet. |
| * Read the packet only if we have the whole thing. |
| */ |
| if ((wupl == 0) || (wupl > E1000_WUPM_BYTES)) |
| return; |
| |
| skb = netdev_alloc_skb_ip_align(netdev, E1000_WUPM_BYTES); |
| if (!skb) |
| return; |
| |
| skb_put(skb, wupl); |
| |
| /* Ensure reads are 32-bit aligned */ |
| wupl = roundup(wupl, 4); |
| |
| memcpy_fromio(skb->data, hw->hw_addr + E1000_WUPM_REG(0), wupl); |
| |
| skb->protocol = eth_type_trans(skb, netdev); |
| netif_rx(skb); |
| } |
| |
| static int igb_suspend(struct device *dev) |
| { |
| return __igb_shutdown(to_pci_dev(dev), NULL, 0); |
| } |
| |
| static int __igb_resume(struct device *dev, bool rpm) |
| { |
| struct pci_dev *pdev = to_pci_dev(dev); |
| struct net_device *netdev = pci_get_drvdata(pdev); |
| struct igb_adapter *adapter = netdev_priv(netdev); |
| struct e1000_hw *hw = &adapter->hw; |
| u32 err, val; |
| |
| pci_set_power_state(pdev, PCI_D0); |
| pci_restore_state(pdev); |
| pci_save_state(pdev); |
| |
| if (!pci_device_is_present(pdev)) |
| return -ENODEV; |
| err = pci_enable_device_mem(pdev); |
| if (err) { |
| dev_err(&pdev->dev, |
| "igb: Cannot enable PCI device from suspend\n"); |
| return err; |
| } |
| pci_set_master(pdev); |
| |
| pci_enable_wake(pdev, PCI_D3hot, 0); |
| pci_enable_wake(pdev, PCI_D3cold, 0); |
| |
| if (igb_init_interrupt_scheme(adapter, true)) { |
| dev_err(&pdev->dev, "Unable to allocate memory for queues\n"); |
| return -ENOMEM; |
| } |
| |
| igb_reset(adapter); |
| |
| /* let the f/w know that the h/w is now under the control of the |
| * driver. |
| */ |
| igb_get_hw_control(adapter); |
| |
| val = rd32(E1000_WUS); |
| if (val & WAKE_PKT_WUS) |
| igb_deliver_wake_packet(netdev); |
| |
| wr32(E1000_WUS, ~0); |
| |
| if (!rpm) |
| rtnl_lock(); |
| if (!err && netif_running(netdev)) |
| err = __igb_open(netdev, true); |
| |
| if (!err) |
| netif_device_attach(netdev); |
| if (!rpm) |
| rtnl_unlock(); |
| |
| return err; |
| } |
| |
| static int igb_resume(struct device *dev) |
| { |
| return __igb_resume(dev, false); |
| } |
| |
| static int igb_runtime_idle(struct device *dev) |
| { |
| struct net_device *netdev = dev_get_drvdata(dev); |
| struct igb_adapter *adapter = netdev_priv(netdev); |
| |
| if (!igb_has_link(adapter)) |
| pm_schedule_suspend(dev, MSEC_PER_SEC * 5); |
| |
| return -EBUSY; |
| } |
| |
| static int igb_runtime_suspend(struct device *dev) |
| { |
| return __igb_shutdown(to_pci_dev(dev), NULL, 1); |
| } |
| |
| static int igb_runtime_resume(struct device *dev) |
| { |
| return __igb_resume(dev, true); |
| } |
| |
| static void igb_shutdown(struct pci_dev *pdev) |
| { |
| bool wake; |
| |
| __igb_shutdown(pdev, &wake, 0); |
| |
| if (system_state == SYSTEM_POWER_OFF) { |
| pci_wake_from_d3(pdev, wake); |
| pci_set_power_state(pdev, PCI_D3hot); |
| } |
| } |
| |
| static int igb_pci_sriov_configure(struct pci_dev *dev, int num_vfs) |
| { |
| #ifdef CONFIG_PCI_IOV |
| int err; |
| |
| if (num_vfs == 0) { |
| return igb_disable_sriov(dev, true); |
| } else { |
| err = igb_enable_sriov(dev, num_vfs, true); |
| return err ? err : num_vfs; |
| } |
| #endif |
| return 0; |
| } |
| |
| /** |
| * igb_io_error_detected - called when PCI error is detected |
| * @pdev: Pointer to PCI device |
| * @state: The current pci connection state |
| * |
| * This function is called after a PCI bus error affecting |
| * this device has been detected. |
| **/ |
| static pci_ers_result_t igb_io_error_detected(struct pci_dev *pdev, |
| pci_channel_state_t state) |
| { |
| struct net_device *netdev = pci_get_drvdata(pdev); |
| struct igb_adapter *adapter = netdev_priv(netdev); |
| |
| if (state == pci_channel_io_normal) { |
| dev_warn(&pdev->dev, "Non-correctable non-fatal error reported.\n"); |
| return PCI_ERS_RESULT_CAN_RECOVER; |
| } |
| |
| netif_device_detach(netdev); |
| |
| if (state == pci_channel_io_perm_failure) |
| return PCI_ERS_RESULT_DISCONNECT; |
| |
| if (netif_running(netdev)) |
| igb_down(adapter); |
| pci_disable_device(pdev); |
| |
| /* Request a slot reset. */ |
| return PCI_ERS_RESULT_NEED_RESET; |
| } |
| |
| /** |
| * igb_io_slot_reset - called after the pci bus has been reset. |
| * @pdev: Pointer to PCI device |
| * |
| * Restart the card from scratch, as if from a cold-boot. Implementation |
| * resembles the first-half of the __igb_resume routine. |
| **/ |
| static pci_ers_result_t igb_io_slot_reset(struct pci_dev *pdev) |
| { |
| struct net_device *netdev = pci_get_drvdata(pdev); |
| struct igb_adapter *adapter = netdev_priv(netdev); |
| struct e1000_hw *hw = &adapter->hw; |
| pci_ers_result_t result; |
| |
| if (pci_enable_device_mem(pdev)) { |
| dev_err(&pdev->dev, |
| "Cannot re-enable PCI device after reset.\n"); |
| result = PCI_ERS_RESULT_DISCONNECT; |
| } else { |
| pci_set_master(pdev); |
| pci_restore_state(pdev); |
| pci_save_state(pdev); |
| |
| pci_enable_wake(pdev, PCI_D3hot, 0); |
| pci_enable_wake(pdev, PCI_D3cold, 0); |
| |
| /* In case of PCI error, adapter lose its HW address |
| * so we should re-assign it here. |
| */ |
| hw->hw_addr = adapter->io_addr; |
| |
| igb_reset(adapter); |
| wr32(E1000_WUS, ~0); |
| result = PCI_ERS_RESULT_RECOVERED; |
| } |
| |
| return result; |
| } |
| |
| /** |
| * igb_io_resume - called when traffic can start flowing again. |
| * @pdev: Pointer to PCI device |
| * |
| * This callback is called when the error recovery driver tells us that |
| * its OK to resume normal operation. Implementation resembles the |
| * second-half of the __igb_resume routine. |
| */ |
| static void igb_io_resume(struct pci_dev *pdev) |
| { |
| struct net_device *netdev = pci_get_drvdata(pdev); |
| struct igb_adapter *adapter = netdev_priv(netdev); |
| |
| if (netif_running(netdev)) { |
| if (igb_up(adapter)) { |
| dev_err(&pdev->dev, "igb_up failed after reset\n"); |
| return; |
| } |
| } |
| |
| netif_device_attach(netdev); |
| |
| /* let the f/w know that the h/w is now under the control of the |
| * driver. |
| */ |
| igb_get_hw_control(adapter); |
| } |
| |
| /** |
| * igb_rar_set_index - Sync RAL[index] and RAH[index] registers with MAC table |
| * @adapter: Pointer to adapter structure |
| * @index: Index of the RAR entry which need to be synced with MAC table |
| **/ |
| static void igb_rar_set_index(struct igb_adapter *adapter, u32 index) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| u32 rar_low, rar_high; |
| u8 *addr = adapter->mac_table[index].addr; |
| |
| /* HW expects these to be in network order when they are plugged |
| * into the registers which are little endian. In order to guarantee |
| * that ordering we need to do an leXX_to_cpup here in order to be |
| * ready for the byteswap that occurs with writel |
| */ |
| rar_low = le32_to_cpup((__le32 *)(addr)); |
| rar_high = le16_to_cpup((__le16 *)(addr + 4)); |
| |
| /* Indicate to hardware the Address is Valid. */ |
| if (adapter->mac_table[index].state & IGB_MAC_STATE_IN_USE) { |
| if (is_valid_ether_addr(addr)) |
| rar_high |= E1000_RAH_AV; |
| |
| if (adapter->mac_table[index].state & IGB_MAC_STATE_SRC_ADDR) |
| rar_high |= E1000_RAH_ASEL_SRC_ADDR; |
| |
| switch (hw->mac.type) { |
| case e1000_82575: |
| case e1000_i210: |
| if (adapter->mac_table[index].state & |
| IGB_MAC_STATE_QUEUE_STEERING) |
| rar_high |= E1000_RAH_QSEL_ENABLE; |
| |
| rar_high |= E1000_RAH_POOL_1 * |
| adapter->mac_table[index].queue; |
| break; |
| default: |
| rar_high |= E1000_RAH_POOL_1 << |
| adapter->mac_table[index].queue; |
| break; |
| } |
| } |
| |
| wr32(E1000_RAL(index), rar_low); |
| wrfl(); |
| wr32(E1000_RAH(index), rar_high); |
| wrfl(); |
| } |
| |
| static int igb_set_vf_mac(struct igb_adapter *adapter, |
| int vf, unsigned char *mac_addr) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| /* VF MAC addresses start at end of receive addresses and moves |
| * towards the first, as a result a collision should not be possible |
| */ |
| int rar_entry = hw->mac.rar_entry_count - (vf + 1); |
| unsigned char *vf_mac_addr = adapter->vf_data[vf].vf_mac_addresses; |
| |
| ether_addr_copy(vf_mac_addr, mac_addr); |
| ether_addr_copy(adapter->mac_table[rar_entry].addr, mac_addr); |
| adapter->mac_table[rar_entry].queue = vf; |
| adapter->mac_table[rar_entry].state |= IGB_MAC_STATE_IN_USE; |
| igb_rar_set_index(adapter, rar_entry); |
| |
| return 0; |
| } |
| |
| static int igb_ndo_set_vf_mac(struct net_device *netdev, int vf, u8 *mac) |
| { |
| struct igb_adapter *adapter = netdev_priv(netdev); |
| |
| if (vf >= adapter->vfs_allocated_count) |
| return -EINVAL; |
| |
| /* Setting the VF MAC to 0 reverts the IGB_VF_FLAG_PF_SET_MAC |
| * flag and allows to overwrite the MAC via VF netdev. This |
| * is necessary to allow libvirt a way to restore the original |
| * MAC after unbinding vfio-pci and reloading igbvf after shutting |
| * down a VM. |
| */ |
| if (is_zero_ether_addr(mac)) { |
| adapter->vf_data[vf].flags &= ~IGB_VF_FLAG_PF_SET_MAC; |
| dev_info(&adapter->pdev->dev, |
| "remove administratively set MAC on VF %d\n", |
| vf); |
| } else if (is_valid_ether_addr(mac)) { |
| adapter->vf_data[vf].flags |= IGB_VF_FLAG_PF_SET_MAC; |
| dev_info(&adapter->pdev->dev, "setting MAC %pM on VF %d\n", |
| mac, vf); |
| dev_info(&adapter->pdev->dev, |
| "Reload the VF driver to make this change effective."); |
| /* Generate additional warning if PF is down */ |
| if (test_bit(__IGB_DOWN, &adapter->state)) { |
| dev_warn(&adapter->pdev->dev, |
| "The VF MAC address has been set, but the PF device is not up.\n"); |
| dev_warn(&adapter->pdev->dev, |
| "Bring the PF device up before attempting to use the VF device.\n"); |
| } |
| } else { |
| return -EINVAL; |
| } |
| return igb_set_vf_mac(adapter, vf, mac); |
| } |
| |
| static int igb_link_mbps(int internal_link_speed) |
| { |
| switch (internal_link_speed) { |
| case SPEED_100: |
| return 100; |
| case SPEED_1000: |
| return 1000; |
| default: |
| return 0; |
| } |
| } |
| |
| static void igb_set_vf_rate_limit(struct e1000_hw *hw, int vf, int tx_rate, |
| int link_speed) |
| { |
| int rf_dec, rf_int; |
| u32 bcnrc_val; |
| |
| if (tx_rate != 0) { |
| /* Calculate the rate factor values to set */ |
| rf_int = link_speed / tx_rate; |
| rf_dec = (link_speed - (rf_int * tx_rate)); |
| rf_dec = (rf_dec * BIT(E1000_RTTBCNRC_RF_INT_SHIFT)) / |
| tx_rate; |
| |
| bcnrc_val = E1000_RTTBCNRC_RS_ENA; |
| bcnrc_val |= FIELD_PREP(E1000_RTTBCNRC_RF_INT_MASK, rf_int); |
| bcnrc_val |= (rf_dec & E1000_RTTBCNRC_RF_DEC_MASK); |
| } else { |
| bcnrc_val = 0; |
| } |
| |
| wr32(E1000_RTTDQSEL, vf); /* vf X uses queue X */ |
| /* Set global transmit compensation time to the MMW_SIZE in RTTBCNRM |
| * register. MMW_SIZE=0x014 if 9728-byte jumbo is supported. |
| */ |
| wr32(E1000_RTTBCNRM, 0x14); |
| wr32(E1000_RTTBCNRC, bcnrc_val); |
| } |
| |
| static void igb_check_vf_rate_limit(struct igb_adapter *adapter) |
| { |
| int actual_link_speed, i; |
| bool reset_rate = false; |
| |
| /* VF TX rate limit was not set or not supported */ |
| if ((adapter->vf_rate_link_speed == 0) || |
| (adapter->hw.mac.type != e1000_82576)) |
| return; |
| |
| actual_link_speed = igb_link_mbps(adapter->link_speed); |
| if (actual_link_speed != adapter->vf_rate_link_speed) { |
| reset_rate = true; |
| adapter->vf_rate_link_speed = 0; |
| dev_info(&adapter->pdev->dev, |
| "Link speed has been changed. VF Transmit rate is disabled\n"); |
| } |
| |
| for (i = 0; i < adapter->vfs_allocated_count; i++) { |
| if (reset_rate) |
| adapter->vf_data[i].tx_rate = 0; |
| |
| igb_set_vf_rate_limit(&adapter->hw, i, |
| adapter->vf_data[i].tx_rate, |
| actual_link_speed); |
| } |
| } |
| |
| static int igb_ndo_set_vf_bw(struct net_device *netdev, int vf, |
| int min_tx_rate, int max_tx_rate) |
| { |
| struct igb_adapter *adapter = netdev_priv(netdev); |
| struct e1000_hw *hw = &adapter->hw; |
| int actual_link_speed; |
| |
| if (hw->mac.type != e1000_82576) |
| return -EOPNOTSUPP; |
| |
| if (min_tx_rate) |
| return -EINVAL; |
| |
| actual_link_speed = igb_link_mbps(adapter->link_speed); |
| if ((vf >= adapter->vfs_allocated_count) || |
| (!(rd32(E1000_STATUS) & E1000_STATUS_LU)) || |
| (max_tx_rate < 0) || |
| (max_tx_rate > actual_link_speed)) |
| return -EINVAL; |
| |
| adapter->vf_rate_link_speed = actual_link_speed; |
| adapter->vf_data[vf].tx_rate = (u16)max_tx_rate; |
| igb_set_vf_rate_limit(hw, vf, max_tx_rate, actual_link_speed); |
| |
| return 0; |
| } |
| |
| static int igb_ndo_set_vf_spoofchk(struct net_device *netdev, int vf, |
| bool setting) |
| { |
| struct igb_adapter *adapter = netdev_priv(netdev); |
| struct e1000_hw *hw = &adapter->hw; |
| u32 reg_val, reg_offset; |
| |
| if (!adapter->vfs_allocated_count) |
| return -EOPNOTSUPP; |
| |
| if (vf >= adapter->vfs_allocated_count) |
| return -EINVAL; |
| |
| reg_offset = (hw->mac.type == e1000_82576) ? E1000_DTXSWC : E1000_TXSWC; |
| reg_val = rd32(reg_offset); |
| if (setting) |
| reg_val |= (BIT(vf) | |
| BIT(vf + E1000_DTXSWC_VLAN_SPOOF_SHIFT)); |
| else |
| reg_val &= ~(BIT(vf) | |
| BIT(vf + E1000_DTXSWC_VLAN_SPOOF_SHIFT)); |
| wr32(reg_offset, reg_val); |
| |
| adapter->vf_data[vf].spoofchk_enabled = setting; |
| return 0; |
| } |
| |
| static int igb_ndo_set_vf_trust(struct net_device *netdev, int vf, bool setting) |
| { |
| struct igb_adapter *adapter = netdev_priv(netdev); |
| |
| if (vf >= adapter->vfs_allocated_count) |
| return -EINVAL; |
| if (adapter->vf_data[vf].trusted == setting) |
| return 0; |
| |
| adapter->vf_data[vf].trusted = setting; |
| |
| dev_info(&adapter->pdev->dev, "VF %u is %strusted\n", |
| vf, setting ? "" : "not "); |
| return 0; |
| } |
| |
| static int igb_ndo_get_vf_config(struct net_device *netdev, |
| int vf, struct ifla_vf_info *ivi) |
| { |
| struct igb_adapter *adapter = netdev_priv(netdev); |
| if (vf >= adapter->vfs_allocated_count) |
| return -EINVAL; |
| ivi->vf = vf; |
| memcpy(&ivi->mac, adapter->vf_data[vf].vf_mac_addresses, ETH_ALEN); |
| ivi->max_tx_rate = adapter->vf_data[vf].tx_rate; |
| ivi->min_tx_rate = 0; |
| ivi->vlan = adapter->vf_data[vf].pf_vlan; |
| ivi->qos = adapter->vf_data[vf].pf_qos; |
| ivi->spoofchk = adapter->vf_data[vf].spoofchk_enabled; |
| ivi->trusted = adapter->vf_data[vf].trusted; |
| return 0; |
| } |
| |
| static void igb_vmm_control(struct igb_adapter *adapter) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| u32 reg; |
| |
| switch (hw->mac.type) { |
| case e1000_82575: |
| case e1000_i210: |
| case e1000_i211: |
| case e1000_i354: |
| default: |
| /* replication is not supported for 82575 */ |
| return; |
| case e1000_82576: |
| /* notify HW that the MAC is adding vlan tags */ |
| reg = rd32(E1000_DTXCTL); |
| reg |= E1000_DTXCTL_VLAN_ADDED; |
| wr32(E1000_DTXCTL, reg); |
| fallthrough; |
| case e1000_82580: |
| /* enable replication vlan tag stripping */ |
| reg = rd32(E1000_RPLOLR); |
| reg |= E1000_RPLOLR_STRVLAN; |
| wr32(E1000_RPLOLR, reg); |
| fallthrough; |
| case e1000_i350: |
| /* none of the above registers are supported by i350 */ |
| break; |
| } |
| |
| if (adapter->vfs_allocated_count) { |
| igb_vmdq_set_loopback_pf(hw, true); |
| igb_vmdq_set_replication_pf(hw, true); |
| igb_vmdq_set_anti_spoofing_pf(hw, true, |
| adapter->vfs_allocated_count); |
| } else { |
| igb_vmdq_set_loopback_pf(hw, false); |
| igb_vmdq_set_replication_pf(hw, false); |
| } |
| } |
| |
| static void igb_init_dmac(struct igb_adapter *adapter, u32 pba) |
| { |
| struct e1000_hw *hw = &adapter->hw; |
| u32 dmac_thr; |
| u16 hwm; |
| u32 reg; |
| |
| if (hw->mac.type > e1000_82580) { |
| if (adapter->flags & IGB_FLAG_DMAC) { |
| /* force threshold to 0. */ |
| wr32(E1000_DMCTXTH, 0); |
| |
| /* DMA Coalescing high water mark needs to be greater |
| * than the Rx threshold. Set hwm to PBA - max frame |
| * size in 16B units, capping it at PBA - 6KB. |
| */ |
| hwm = 64 * (pba - 6); |
| reg = rd32(E1000_FCRTC); |
| reg &= ~E1000_FCRTC_RTH_COAL_MASK; |
| reg |= FIELD_PREP(E1000_FCRTC_RTH_COAL_MASK, hwm); |
| wr32(E1000_FCRTC, reg); |
| |
| /* Set the DMA Coalescing Rx threshold to PBA - 2 * max |
| * frame size, capping it at PBA - 10KB. |
| */ |
| dmac_thr = pba - 10; |
| reg = rd32(E1000_DMACR); |
| reg &= ~E1000_DMACR_DMACTHR_MASK; |
| reg |= FIELD_PREP(E1000_DMACR_DMACTHR_MASK, dmac_thr); |
| |
| /* transition to L0x or L1 if available..*/ |
| reg |= (E1000_DMACR_DMAC_EN | E1000_DMACR_DMAC_LX_MASK); |
| |
| /* watchdog timer= +-1000 usec in 32usec intervals */ |
| reg |= (1000 >> 5); |
| |
| /* Disable BMC-to-OS Watchdog Enable */ |
| if (hw->mac.type != e1000_i354) |
| reg &= ~E1000_DMACR_DC_BMC2OSW_EN; |
| wr32(E1000_DMACR, reg); |
| |
| /* no lower threshold to disable |
| * coalescing(smart fifb)-UTRESH=0 |
| */ |
| wr32(E1000_DMCRTRH, 0); |
| |
| reg = (IGB_DMCTLX_DCFLUSH_DIS | 0x4); |
| |
| wr32(E1000_DMCTLX, reg); |
| |
| /* free space in tx packet buffer to wake from |
| * DMA coal |
| */ |
| wr32(E1000_DMCTXTH, (IGB_MIN_TXPBSIZE - |
| (IGB_TX_BUF_4096 + adapter->max_frame_size)) >> 6); |
| } |
| |
| if (hw->mac.type >= e1000_i210 || |
| (adapter->flags & IGB_FLAG_DMAC)) { |
| reg = rd32(E1000_PCIEMISC); |
| reg |= E1000_PCIEMISC_LX_DECISION; |
| wr32(E1000_PCIEMISC, reg); |
| } /* endif adapter->dmac is not disabled */ |
| } else if (hw->mac.type == e1000_82580) { |
| u32 reg = rd32(E1000_PCIEMISC); |
| |
| wr32(E1000_PCIEMISC, reg & ~E1000_PCIEMISC_LX_DECISION); |
| wr32(E1000_DMACR, 0); |
| } |
| } |
| |
| /** |
| * igb_read_i2c_byte - Reads 8 bit word over I2C |
| * @hw: pointer to hardware structure |
| * @byte_offset: byte offset to read |
| * @dev_addr: device address |
| * @data: value read |
| * |
| * Performs byte read operation over I2C interface at |
| * a specified device address. |
| **/ |
| s32 igb_read_i2c_byte(struct e1000_hw *hw, u8 byte_offset, |
| u8 dev_addr, u8 *data) |
| { |
| struct igb_adapter *adapter = container_of(hw, struct igb_adapter, hw); |
| struct i2c_client *this_client = adapter->i2c_client; |
| s32 status; |
| u16 swfw_mask = 0; |
| |
| if (!this_client) |
| return E1000_ERR_I2C; |
| |
| swfw_mask = E1000_SWFW_PHY0_SM; |
| |
| if (hw->mac.ops.acquire_swfw_sync(hw, swfw_mask)) |
| return E1000_ERR_SWFW_SYNC; |
| |
| status = i2c_smbus_read_byte_data(this_client, byte_offset); |
| hw->mac.ops.release_swfw_sync(hw, swfw_mask); |
| |
| if (status < 0) |
| return E1000_ERR_I2C; |
| else { |
| *data = status; |
| return 0; |
| } |
| } |
| |
| /** |
| * igb_write_i2c_byte - Writes 8 bit word over I2C |
| * @hw: pointer to hardware structure |
| * @byte_offset: byte offset to write |
| * @dev_addr: device address |
| * @data: value to write |
| * |
| * Performs byte write operation over I2C interface at |
| * a specified device address. |
| **/ |
| s32 igb_write_i2c_byte(struct e1000_hw *hw, u8 byte_offset, |
| u8 dev_addr, u8 data) |
| { |
| struct igb_adapter *adapter = container_of(hw, struct igb_adapter, hw); |
| struct i2c_client *this_client = adapter->i2c_client; |
| s32 status; |
| u16 swfw_mask = E1000_SWFW_PHY0_SM; |
| |
| if (!this_client) |
| return E1000_ERR_I2C; |
| |
| if (hw->mac.ops.acquire_swfw_sync(hw, swfw_mask)) |
| return E1000_ERR_SWFW_SYNC; |
| status = i2c_smbus_write_byte_data(this_client, byte_offset, data); |
| hw->mac.ops.release_swfw_sync(hw, swfw_mask); |
| |
| if (status) |
| return E1000_ERR_I2C; |
| else |
| return 0; |
| |
| } |
| |
| int igb_reinit_queues(struct igb_adapter *adapter) |
| { |
| struct net_device *netdev = adapter->netdev; |
| struct pci_dev *pdev = adapter->pdev; |
| int err = 0; |
| |
| if (netif_running(netdev)) |
| igb_close(netdev); |
| |
| igb_reset_interrupt_capability(adapter); |
| |
| if (igb_init_interrupt_scheme(adapter, true)) { |
| dev_err(&pdev->dev, "Unable to allocate memory for queues\n"); |
| return -ENOMEM; |
| } |
| |
| if (netif_running(netdev)) |
| err = igb_open(netdev); |
| |
| return err; |
| } |
| |
| static void igb_nfc_filter_exit(struct igb_adapter *adapter) |
| { |
| struct igb_nfc_filter *rule; |
| |
| spin_lock(&adapter->nfc_lock); |
| |
| hlist_for_each_entry(rule, &adapter->nfc_filter_list, nfc_node) |
| igb_erase_filter(adapter, rule); |
| |
| hlist_for_each_entry(rule, &adapter->cls_flower_list, nfc_node) |
| igb_erase_filter(adapter, rule); |
| |
| spin_unlock(&adapter->nfc_lock); |
| } |
| |
| static void igb_nfc_filter_restore(struct igb_adapter *adapter) |
| { |
| struct igb_nfc_filter *rule; |
| |
| spin_lock(&adapter->nfc_lock); |
| |
| hlist_for_each_entry(rule, &adapter->nfc_filter_list, nfc_node) |
| igb_add_filter(adapter, rule); |
| |
| spin_unlock(&adapter->nfc_lock); |
| } |
| |
| static _DEFINE_DEV_PM_OPS(igb_pm_ops, igb_suspend, igb_resume, |
| igb_runtime_suspend, igb_runtime_resume, |
| igb_runtime_idle); |
| |
| static struct pci_driver igb_driver = { |
| .name = igb_driver_name, |
| .id_table = igb_pci_tbl, |
| .probe = igb_probe, |
| .remove = igb_remove, |
| .driver.pm = pm_ptr(&igb_pm_ops), |
| .shutdown = igb_shutdown, |
| .sriov_configure = igb_pci_sriov_configure, |
| .err_handler = &igb_err_handler |
| }; |
| |
| /* igb_main.c */ |