| // SPDX-License-Identifier: BSD-3-Clause |
| |
| /dts-v1/; |
| |
| #include "qcom-msm8226.dtsi" |
| #include "pm8226.dtsi" |
| |
| /delete-node/ &smem_region; |
| |
| / { |
| model = "Motorola Moto G 4G (2013)"; |
| compatible = "motorola,peregrine", "qcom,msm8926", "qcom,msm8226"; |
| chassis-type = "handset"; |
| |
| aliases { |
| mmc0 = &sdhc_1; /* SDC1 eMMC slot */ |
| mmc1 = &sdhc_2; /* SDC2 SD card slot */ |
| }; |
| |
| chosen { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| framebuffer0: framebuffer@3200000 { |
| compatible = "simple-framebuffer"; |
| reg = <0x03200000 0x800000>; |
| width = <720>; |
| height = <1280>; |
| stride = <(720 * 3)>; |
| format = "r8g8b8"; |
| vsp-supply = <®_lcd_pos>; |
| vsn-supply = <®_lcd_neg>; |
| vdd-supply = <&pm8226_l28>; |
| vddio-supply = <&vddio_disp_vreg>; |
| }; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| |
| event-hall-sensor { |
| label = "Hall Effect Sensor"; |
| gpios = <&tlmm 51 GPIO_ACTIVE_LOW>; |
| linux,input-type = <EV_SW>; |
| linux,code = <SW_LID>; |
| linux,can-disable; |
| }; |
| |
| key-volume-up { |
| label = "Volume Up"; |
| gpios = <&tlmm 106 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_VOLUMEUP>; |
| debounce-interval = <15>; |
| }; |
| }; |
| |
| vddio_disp_vreg: regulator-vddio-disp { |
| compatible = "regulator-fixed"; |
| regulator-name = "vddio_disp"; |
| gpio = <&tlmm 34 GPIO_ACTIVE_HIGH>; |
| startup-delay-us = <300>; |
| enable-active-high; |
| regulator-boot-on; |
| vin-supply = <&pm8226_l8>; |
| pinctrl-0 = <&disp_vddio_default>; |
| pinctrl-names = "default"; |
| }; |
| |
| reserved-memory { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| framebuffer@3200000 { |
| reg = <0x03200000 0x800000>; |
| no-map; |
| }; |
| |
| smem_region: smem@fa00000 { |
| reg = <0x0fa00000 0x100000>; |
| no-map; |
| }; |
| }; |
| }; |
| |
| &blsp1_i2c2 { |
| clock-frequency = <100000>; |
| status = "okay"; |
| |
| magnetometer@c { |
| compatible = "asahi-kasei,ak8963"; |
| reg = <0xc>; |
| interrupts-extended = <&tlmm 38 IRQ_TYPE_EDGE_FALLING>; |
| reset-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>; |
| vdd-supply = <&pm8226_l19>; |
| pinctrl-0 = <&mag_int_default &mag_reset_default>; |
| pinctrl-names = "default"; |
| }; |
| |
| accelerometer@18 { |
| compatible = "st,lis3dh-accel"; |
| reg = <0x18>; |
| interrupts-extended = <&tlmm 1 IRQ_TYPE_EDGE_FALLING>; |
| vdd-supply = <&pm8226_l19>; |
| pinctrl-0 = <&accel_int_default>; |
| pinctrl-names = "default"; |
| st,drdy-int-pin = <1>; |
| }; |
| }; |
| |
| &blsp1_i2c3 { |
| clock-frequency = <400000>; |
| status = "okay"; |
| |
| regulator@3e { |
| compatible = "ti,tps65132"; |
| reg = <0x3e>; |
| pinctrl-0 = <®_lcd_default>; |
| pinctrl-names = "default"; |
| |
| reg_lcd_pos: outp { |
| regulator-name = "outp"; |
| regulator-min-microvolt = <4000000>; |
| regulator-max-microvolt = <6000000>; |
| regulator-active-discharge = <1>; |
| regulator-boot-on; |
| enable-gpios = <&tlmm 31 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| reg_lcd_neg: outn { |
| regulator-name = "outn"; |
| regulator-min-microvolt = <4000000>; |
| regulator-max-microvolt = <6000000>; |
| regulator-active-discharge = <1>; |
| regulator-boot-on; |
| enable-gpios = <&tlmm 33 GPIO_ACTIVE_HIGH>; |
| }; |
| }; |
| |
| sensor@48 { |
| compatible = "ti,tmp108"; |
| reg = <0x48>; |
| interrupts-extended = <&tlmm 13 IRQ_TYPE_LEVEL_LOW>; |
| pinctrl-0 = <&temp_alert_default>; |
| pinctrl-names = "default"; |
| #thermal-sensor-cells = <0>; |
| }; |
| }; |
| |
| &blsp1_uart3 { |
| status = "okay"; |
| }; |
| |
| &pm8226_resin { |
| linux,code = <KEY_VOLUMEDOWN>; |
| status = "okay"; |
| }; |
| |
| &pm8226_vib { |
| status = "okay"; |
| }; |
| |
| &rpm_requests { |
| regulators { |
| compatible = "qcom,rpm-pm8226-regulators"; |
| |
| pm8226_s3: s3 { |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1300000>; |
| }; |
| |
| pm8226_s4: s4 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2200000>; |
| }; |
| |
| pm8226_s5: s5 { |
| regulator-min-microvolt = <1150000>; |
| regulator-max-microvolt = <1150000>; |
| }; |
| |
| pm8226_l1: l1 { |
| regulator-min-microvolt = <1225000>; |
| regulator-max-microvolt = <1225000>; |
| }; |
| |
| pm8226_l2: l2 { |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| }; |
| |
| pm8226_l3: l3 { |
| regulator-min-microvolt = <750000>; |
| regulator-max-microvolt = <1337500>; |
| }; |
| |
| pm8226_l4: l4 { |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| }; |
| |
| pm8226_l5: l5 { |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| }; |
| |
| pm8226_l6: l6 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-allow-set-load; |
| }; |
| |
| pm8226_l7: l7 { |
| regulator-min-microvolt = <1850000>; |
| regulator-max-microvolt = <1850000>; |
| }; |
| |
| pm8226_l8: l8 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| pm8226_l9: l9 { |
| regulator-min-microvolt = <2050000>; |
| regulator-max-microvolt = <2050000>; |
| }; |
| |
| pm8226_l10: l10 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| pm8226_l12: l12 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| pm8226_l14: l14 { |
| regulator-min-microvolt = <2750000>; |
| regulator-max-microvolt = <2750000>; |
| }; |
| |
| pm8226_l15: l15 { |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| }; |
| |
| pm8226_l16: l16 { |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3350000>; |
| }; |
| |
| pm8226_l17: l17 { |
| regulator-min-microvolt = <2950000>; |
| regulator-max-microvolt = <2950000>; |
| }; |
| |
| pm8226_l18: l18 { |
| regulator-min-microvolt = <2950000>; |
| regulator-max-microvolt = <2950000>; |
| }; |
| |
| pm8226_l19: l19 { |
| regulator-min-microvolt = <2850000>; |
| regulator-max-microvolt = <2850000>; |
| }; |
| |
| pm8226_l20: l20 { |
| regulator-min-microvolt = <3075000>; |
| regulator-max-microvolt = <3075000>; |
| }; |
| |
| pm8226_l21: l21 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2950000>; |
| regulator-allow-set-load; |
| }; |
| |
| pm8226_l22: l22 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2950000>; |
| }; |
| |
| pm8226_l23: l23 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2950000>; |
| }; |
| |
| pm8226_l24: l24 { |
| regulator-min-microvolt = <1300000>; |
| regulator-max-microvolt = <1350000>; |
| }; |
| |
| pm8226_l25: l25 { |
| regulator-min-microvolt = <1775000>; |
| regulator-max-microvolt = <2125000>; |
| }; |
| |
| pm8226_l26: l26 { |
| regulator-min-microvolt = <1225000>; |
| regulator-max-microvolt = <1225000>; |
| }; |
| |
| pm8226_l27: l27 { |
| regulator-min-microvolt = <2050000>; |
| regulator-max-microvolt = <2050000>; |
| }; |
| |
| pm8226_l28: l28 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3400000>; |
| regulator-boot-on; |
| }; |
| |
| pm8226_lvs1: lvs1 { |
| /* Pull-up for I2C lines */ |
| regulator-always-on; |
| }; |
| }; |
| }; |
| |
| &sdhc_1 { |
| vmmc-supply = <&pm8226_l17>; |
| vqmmc-supply = <&pm8226_l6>; |
| |
| bus-width = <8>; |
| non-removable; |
| |
| status = "okay"; |
| }; |
| |
| &sdhc_2 { |
| vmmc-supply = <&pm8226_l18>; |
| vqmmc-supply = <&pm8226_l21>; |
| |
| bus-width = <4>; |
| cd-gpios = <&tlmm 115 GPIO_ACTIVE_HIGH>; |
| |
| status = "okay"; |
| }; |
| |
| &smbb { |
| qcom,fast-charge-safe-current = <2000000>; |
| qcom,fast-charge-current-limit = <1900000>; |
| qcom,fast-charge-safe-voltage = <4400000>; |
| qcom,minimum-input-voltage = <4300000>; |
| |
| status = "okay"; |
| }; |
| |
| &tlmm { |
| accel_int_default: accel-int-default-state { |
| pins = "gpio1"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| output-disable; |
| }; |
| |
| disp_vddio_default: disp-vddio-default-state { |
| pins = "gpio34"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| output-high; |
| }; |
| |
| mag_int_default: mag-int-default-state { |
| pins = "gpio38"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| output-disable; |
| }; |
| |
| mag_reset_default: mag-reset-default-state { |
| pins = "gpio62"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| output-high; |
| }; |
| |
| reg_lcd_default: reg-lcd-default-state { |
| pins = "gpio31", "gpio33"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| output-high; |
| }; |
| |
| temp_alert_default: temp-alert-default-state { |
| pins = "gpio13"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| output-disable; |
| }; |
| }; |
| |
| &usb { |
| extcon = <&smbb>; |
| dr_mode = "peripheral"; |
| status = "okay"; |
| }; |
| |
| &usb_hs_phy { |
| extcon = <&smbb>; |
| v1p8-supply = <&pm8226_l10>; |
| v3p3-supply = <&pm8226_l20>; |
| }; |
