| # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) |
| # Copyright 2021 ARM Ltd. |
| %YAML 1.2 |
| --- |
| $id: http://devicetree.org/schemas/firmware/arm,scmi.yaml# |
| $schema: http://devicetree.org/meta-schemas/core.yaml# |
| |
| title: System Control and Management Interface (SCMI) Message Protocol |
| |
| maintainers: |
| - Sudeep Holla <sudeep.holla@arm.com> |
| |
| description: | |
| The SCMI is intended to allow agents such as OSPM to manage various functions |
| that are provided by the hardware platform it is running on, including power |
| and performance functions. |
| |
| This binding is intended to define the interface the firmware implementing |
| the SCMI as described in ARM document number ARM DEN 0056 ("ARM System Control |
| and Management Interface Platform Design Document")[0] provide for OSPM in |
| the device tree. |
| |
| [0] https://developer.arm.com/documentation/den0056/latest |
| |
| anyOf: |
| - $ref: /schemas/firmware/nxp,imx95-scmi.yaml |
| |
| properties: |
| $nodename: |
| const: scmi |
| |
| compatible: |
| oneOf: |
| - description: SCMI compliant firmware with mailbox transport |
| items: |
| - const: arm,scmi |
| - description: SCMI compliant firmware with ARM SMC/HVC transport |
| items: |
| - const: arm,scmi-smc |
| - description: SCMI compliant firmware with ARM SMC/HVC transport |
| with shmem address(4KB-page, offset) as parameters |
| items: |
| - const: arm,scmi-smc-param |
| - description: SCMI compliant firmware with Qualcomm SMC/HVC transport |
| items: |
| - const: qcom,scmi-smc |
| - description: SCMI compliant firmware with SCMI Virtio transport. |
| The virtio transport only supports a single device. |
| items: |
| - const: arm,scmi-virtio |
| - description: SCMI compliant firmware with OP-TEE transport |
| items: |
| - const: linaro,scmi-optee |
| |
| interrupts: |
| description: |
| The interrupt that indicates message completion by the platform |
| rather than by the return of the smc call. This should not be used |
| except when the platform requires such behavior. |
| maxItems: 1 |
| |
| interrupt-names: |
| const: a2p |
| |
| mbox-names: |
| description: |
| Specifies the mailboxes used to communicate with SCMI compliant |
| firmware. |
| oneOf: |
| - items: |
| - const: tx |
| - const: rx |
| minItems: 1 |
| - items: |
| - const: tx |
| - const: tx_reply |
| - const: rx |
| - const: rx_reply |
| minItems: 2 |
| |
| mboxes: |
| description: |
| List of phandle and mailbox channel specifiers. It should contain |
| exactly one, two, three or four mailboxes; the first one or two for |
| transmitting messages ("tx") and another optional ("rx") for receiving |
| notifications and delayed responses, if supported by the platform. |
| The optional ("rx_reply") is for notifications completion interrupt, |
| if supported by the platform. |
| The number of mailboxes needed for transmitting messages depends on the |
| type of channels exposed by the specific underlying mailbox controller; |
| one single channel descriptor is enough if such channel is bidirectional, |
| while two channel descriptors are needed to represent the SCMI ("tx") |
| channel if the underlying mailbox channels are of unidirectional type. |
| The effective combination in numbers of mboxes and shmem descriptors let |
| the SCMI subsystem determine unambiguosly which type of SCMI channels are |
| made available by the underlying mailbox controller and how to use them. |
| 1 mbox / 1 shmem => SCMI TX over 1 mailbox bidirectional channel |
| 2 mbox / 2 shmem => SCMI TX and RX over 2 mailbox bidirectional channels |
| 2 mbox / 1 shmem => SCMI TX over 2 mailbox unidirectional channels |
| 3 mbox / 2 shmem => SCMI TX and RX over 3 mailbox unidirectional channels |
| 4 mbox / 2 shmem => SCMI TX and RX over 4 mailbox unidirectional channels |
| Any other combination of mboxes and shmem is invalid. |
| minItems: 1 |
| maxItems: 4 |
| |
| shmem: |
| description: |
| List of phandle pointing to the shared memory(SHM) area, for each |
| transport channel specified. |
| minItems: 1 |
| maxItems: 2 |
| |
| '#address-cells': |
| const: 1 |
| |
| '#size-cells': |
| const: 0 |
| |
| atomic-threshold-us: |
| description: |
| An optional time value, expressed in microseconds, representing, on this |
| platform, the threshold above which any SCMI command, advertised to have |
| an higher-than-threshold execution latency, should not be considered for |
| atomic mode of operation, even if requested. |
| default: 0 |
| |
| max-rx-timeout-ms: |
| description: |
| An optional time value, expressed in milliseconds, representing the |
| transport maximum timeout value for the receive channel. The value should |
| be a non-zero value if set. |
| minimum: 1 |
| |
| arm,smc-id: |
| $ref: /schemas/types.yaml#/definitions/uint32 |
| description: |
| SMC id required when using smc or hvc transports |
| |
| linaro,optee-channel-id: |
| $ref: /schemas/types.yaml#/definitions/uint32 |
| description: |
| Channel specifier required when using OP-TEE transport. |
| |
| protocol@11: |
| $ref: '#/$defs/protocol-node' |
| unevaluatedProperties: false |
| |
| properties: |
| reg: |
| const: 0x11 |
| |
| '#power-domain-cells': |
| const: 1 |
| |
| required: |
| - '#power-domain-cells' |
| |
| protocol@12: |
| $ref: '#/$defs/protocol-node' |
| unevaluatedProperties: false |
| |
| properties: |
| reg: |
| const: 0x12 |
| |
| protocol@13: |
| $ref: '#/$defs/protocol-node' |
| unevaluatedProperties: false |
| |
| properties: |
| reg: |
| const: 0x13 |
| |
| '#clock-cells': |
| const: 1 |
| |
| '#power-domain-cells': |
| const: 1 |
| |
| oneOf: |
| - required: |
| - '#clock-cells' |
| |
| - required: |
| - '#power-domain-cells' |
| |
| protocol@14: |
| $ref: '#/$defs/protocol-node' |
| unevaluatedProperties: false |
| |
| properties: |
| reg: |
| const: 0x14 |
| |
| '#clock-cells': |
| const: 1 |
| |
| required: |
| - '#clock-cells' |
| |
| protocol@15: |
| $ref: '#/$defs/protocol-node' |
| unevaluatedProperties: false |
| |
| properties: |
| reg: |
| const: 0x15 |
| |
| '#thermal-sensor-cells': |
| const: 1 |
| |
| required: |
| - '#thermal-sensor-cells' |
| |
| protocol@16: |
| $ref: '#/$defs/protocol-node' |
| unevaluatedProperties: false |
| |
| properties: |
| reg: |
| const: 0x16 |
| |
| '#reset-cells': |
| const: 1 |
| |
| required: |
| - '#reset-cells' |
| |
| protocol@17: |
| $ref: '#/$defs/protocol-node' |
| unevaluatedProperties: false |
| |
| properties: |
| reg: |
| const: 0x17 |
| |
| regulators: |
| type: object |
| additionalProperties: false |
| description: |
| The list of all regulators provided by this SCMI controller. |
| |
| properties: |
| '#address-cells': |
| const: 1 |
| |
| '#size-cells': |
| const: 0 |
| |
| patternProperties: |
| '^regulator@[0-9a-f]+$': |
| type: object |
| $ref: /schemas/regulator/regulator.yaml# |
| unevaluatedProperties: false |
| |
| properties: |
| reg: |
| maxItems: 1 |
| description: Identifier for the voltage regulator. |
| |
| required: |
| - reg |
| |
| protocol@18: |
| $ref: '#/$defs/protocol-node' |
| unevaluatedProperties: false |
| |
| properties: |
| reg: |
| const: 0x18 |
| |
| protocol@19: |
| type: object |
| allOf: |
| - $ref: '#/$defs/protocol-node' |
| - anyOf: |
| - $ref: /schemas/pinctrl/pinctrl.yaml |
| - $ref: /schemas/firmware/nxp,imx95-scmi-pinctrl.yaml |
| |
| unevaluatedProperties: false |
| |
| properties: |
| reg: |
| const: 0x19 |
| |
| patternProperties: |
| '-pins$': |
| type: object |
| allOf: |
| - $ref: /schemas/pinctrl/pincfg-node.yaml# |
| - $ref: /schemas/pinctrl/pinmux-node.yaml# |
| unevaluatedProperties: false |
| |
| description: |
| A pin multiplexing sub-node describes how to configure a |
| set of pins in some desired function. |
| A single sub-node may define several pin configurations. |
| This sub-node is using the default pinctrl bindings to configure |
| pin multiplexing and using SCMI protocol to apply a specified |
| configuration. |
| |
| required: |
| - reg |
| |
| unevaluatedProperties: false |
| |
| $defs: |
| protocol-node: |
| type: object |
| description: |
| Each sub-node represents a protocol supported. If the platform |
| supports a dedicated communication channel for a particular protocol, |
| then the corresponding transport properties must be present. |
| The virtio transport does not support a dedicated communication channel. |
| |
| properties: |
| reg: |
| maxItems: 1 |
| |
| mbox-names: |
| oneOf: |
| - items: |
| - const: tx |
| - const: rx |
| minItems: 1 |
| - items: |
| - const: tx |
| - const: tx_reply |
| - const: rx |
| minItems: 2 |
| |
| mboxes: |
| minItems: 1 |
| maxItems: 3 |
| |
| shmem: |
| minItems: 1 |
| maxItems: 2 |
| |
| linaro,optee-channel-id: |
| $ref: /schemas/types.yaml#/definitions/uint32 |
| description: |
| Channel specifier required when using OP-TEE transport and |
| protocol has a dedicated communication channel. |
| |
| required: |
| - reg |
| |
| required: |
| - compatible |
| |
| if: |
| properties: |
| compatible: |
| contains: |
| const: arm,scmi |
| then: |
| properties: |
| interrupts: false |
| interrupt-names: false |
| |
| required: |
| - mboxes |
| - shmem |
| |
| else: |
| if: |
| properties: |
| compatible: |
| contains: |
| enum: |
| - arm,scmi-smc |
| - arm,scmi-smc-param |
| - qcom,scmi-smc |
| then: |
| required: |
| - arm,smc-id |
| - shmem |
| |
| else: |
| if: |
| properties: |
| compatible: |
| contains: |
| const: linaro,scmi-optee |
| then: |
| required: |
| - linaro,optee-channel-id |
| |
| examples: |
| - | |
| firmware { |
| scmi { |
| compatible = "arm,scmi"; |
| mboxes = <&mhuB 0 0>, |
| <&mhuB 0 1>; |
| mbox-names = "tx", "rx"; |
| shmem = <&cpu_scp_lpri0>, |
| <&cpu_scp_lpri1>; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| atomic-threshold-us = <10000>; |
| |
| scmi_devpd: protocol@11 { |
| reg = <0x11>; |
| #power-domain-cells = <1>; |
| }; |
| |
| scmi_dvfs: protocol@13 { |
| reg = <0x13>; |
| #power-domain-cells = <1>; |
| |
| mboxes = <&mhuB 1 0>, |
| <&mhuB 1 1>; |
| mbox-names = "tx", "rx"; |
| shmem = <&cpu_scp_hpri0>, |
| <&cpu_scp_hpri1>; |
| }; |
| |
| scmi_clk: protocol@14 { |
| reg = <0x14>; |
| #clock-cells = <1>; |
| }; |
| |
| scmi_sensors: protocol@15 { |
| reg = <0x15>; |
| #thermal-sensor-cells = <1>; |
| }; |
| |
| scmi_reset: protocol@16 { |
| reg = <0x16>; |
| #reset-cells = <1>; |
| }; |
| |
| scmi_voltage: protocol@17 { |
| reg = <0x17>; |
| regulators { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| regulator_devX: regulator@0 { |
| reg = <0x0>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| |
| regulator_devY: regulator@9 { |
| reg = <0x9>; |
| regulator-min-microvolt = <500000>; |
| regulator-max-microvolt = <4200000>; |
| }; |
| }; |
| }; |
| |
| scmi_powercap: protocol@18 { |
| reg = <0x18>; |
| }; |
| |
| scmi_pinctrl: protocol@19 { |
| reg = <0x19>; |
| |
| i2c2-pins { |
| groups = "g_i2c2_a", "g_i2c2_b"; |
| function = "f_i2c2"; |
| }; |
| |
| mdio-pins { |
| groups = "g_avb_mdio"; |
| drive-strength = <24>; |
| }; |
| |
| keys_pins: keys-pins { |
| pins = "gpio_5_17", "gpio_5_20", "gpio_5_22", "gpio_2_1"; |
| bias-pull-up; |
| }; |
| }; |
| }; |
| }; |
| |
| soc { |
| #address-cells = <2>; |
| #size-cells = <2>; |
| |
| sram@50000000 { |
| compatible = "mmio-sram"; |
| reg = <0x0 0x50000000 0x0 0x10000>; |
| |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0x0 0x50000000 0x10000>; |
| |
| cpu_scp_lpri0: scp-sram-section@0 { |
| compatible = "arm,scmi-shmem"; |
| reg = <0x0 0x80>; |
| }; |
| |
| cpu_scp_lpri1: scp-sram-section@80 { |
| compatible = "arm,scmi-shmem"; |
| reg = <0x80 0x80>; |
| }; |
| |
| cpu_scp_hpri0: scp-sram-section@100 { |
| compatible = "arm,scmi-shmem"; |
| reg = <0x100 0x80>; |
| }; |
| |
| cpu_scp_hpri2: scp-sram-section@180 { |
| compatible = "arm,scmi-shmem"; |
| reg = <0x180 0x80>; |
| }; |
| }; |
| }; |
| |
| - | |
| firmware { |
| scmi { |
| compatible = "arm,scmi-smc"; |
| shmem = <&cpu_scp_lpri0>, <&cpu_scp_lpri1>; |
| arm,smc-id = <0xc3000001>; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| scmi_devpd1: protocol@11 { |
| reg = <0x11>; |
| #power-domain-cells = <1>; |
| }; |
| }; |
| }; |
| |
| - | |
| firmware { |
| scmi { |
| compatible = "linaro,scmi-optee"; |
| linaro,optee-channel-id = <0>; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| scmi_dvfs1: protocol@13 { |
| reg = <0x13>; |
| linaro,optee-channel-id = <1>; |
| shmem = <&cpu_optee_lpri0>; |
| #power-domain-cells = <1>; |
| }; |
| |
| scmi_clk0: protocol@14 { |
| reg = <0x14>; |
| #clock-cells = <1>; |
| }; |
| }; |
| }; |
| |
| soc { |
| #address-cells = <2>; |
| #size-cells = <2>; |
| |
| sram@51000000 { |
| compatible = "mmio-sram"; |
| reg = <0x0 0x51000000 0x0 0x10000>; |
| |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0x0 0x51000000 0x10000>; |
| |
| cpu_optee_lpri0: optee-sram-section@0 { |
| compatible = "arm,scmi-shmem"; |
| reg = <0x0 0x80>; |
| }; |
| }; |
| }; |
| |
| ... |
