| // SPDX-License-Identifier: GPL-2.0-only |
| |
| /dts-v1/; |
| |
| #include "msm8916-pm8916.dtsi" |
| #include "msm8916-modem-qdsp6.dtsi" |
| |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/leds/common.h> |
| |
| / { |
| model = "GPLUS FL8005A"; |
| compatible = "gplus,fl8005a", "qcom,msm8916"; |
| chassis-type = "tablet"; |
| |
| aliases { |
| mmc0 = &sdhc_1; /* eMMC */ |
| mmc1 = &sdhc_2; /* SD card */ |
| serial0 = &blsp_uart2; |
| }; |
| |
| chosen { |
| stdout-path = "serial0"; |
| }; |
| |
| battery: battery { |
| compatible = "simple-battery"; |
| device-chemistry = "lithium-ion-polymer"; |
| voltage-min-design-microvolt = <3700000>; |
| voltage-max-design-microvolt = <4200000>; |
| energy-full-design-microwatt-hours = <13690000>; |
| charge-full-design-microamp-hours = <3700000>; |
| |
| ocv-capacity-celsius = <25>; |
| ocv-capacity-table-0 = |
| <4186000 100>, <4126000 95>, <4078000 90>, |
| <4036000 85>, <3997000 80>, <3962000 75>, |
| <3932000 70>, <3904000 65>, <3874000 60>, |
| <3839000 55>, <3809000 50>, <3792000 45>, |
| <3780000 40>, <3772000 35>, <3764000 30>, |
| <3752000 25>, <3731000 20>, <3704000 16>, |
| <3677000 13>, <3670000 11>, <3668000 10>, |
| <3666000 9>, <3662000 8>, <3658000 7>, <3648000 6>, |
| <3624000 5>, <3580000 4>, <3518000 3>, <3434000 2>, |
| <3310000 1>, <3000000 0>; |
| }; |
| |
| flash-led-controller { |
| /* Actually qcom,leds-gpio-flash */ |
| compatible = "sgmicro,sgm3140"; |
| enable-gpios = <&tlmm 31 GPIO_ACTIVE_HIGH>; |
| flash-gpios = <&tlmm 32 GPIO_ACTIVE_HIGH>; |
| |
| pinctrl-0 = <&camera_flash_default>; |
| pinctrl-names = "default"; |
| |
| flash_led: led { |
| function = LED_FUNCTION_FLASH; |
| color = <LED_COLOR_ID_WHITE>; |
| flash-max-timeout-us = <250000>; |
| }; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| |
| pinctrl-0 = <&gpio_keys_default>; |
| pinctrl-names = "default"; |
| |
| button-volume-up { |
| label = "Volume Up"; |
| gpios = <&tlmm 107 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_VOLUMEUP>; |
| }; |
| }; |
| |
| gpio-leds { |
| compatible = "gpio-leds"; |
| |
| pinctrl-0 = <&gpio_leds_default>; |
| pinctrl-names = "default"; |
| |
| led-red { |
| function = LED_FUNCTION_CHARGING; |
| color = <LED_COLOR_ID_RED>; |
| gpios = <&tlmm 117 GPIO_ACTIVE_HIGH>; |
| retain-state-suspended; |
| }; |
| |
| led-green { |
| function = LED_FUNCTION_CHARGING; |
| color = <LED_COLOR_ID_GREEN>; |
| gpios = <&tlmm 118 GPIO_ACTIVE_HIGH>; |
| retain-state-suspended; |
| }; |
| }; |
| |
| usb_id: usb-id { |
| compatible = "linux,extcon-usb-gpio"; |
| id-gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>; |
| pinctrl-0 = <&usb_id_default>; |
| pinctrl-names = "default"; |
| }; |
| }; |
| |
| &blsp_i2c5 { |
| status = "okay"; |
| |
| touchscreen@38 { |
| /* Actually ft5402 */ |
| compatible = "edt,edt-ft5406"; |
| reg = <0x38>; |
| |
| interrupt-parent = <&tlmm>; |
| interrupts = <13 IRQ_TYPE_EDGE_FALLING>; |
| |
| reset-gpios = <&tlmm 12 GPIO_ACTIVE_LOW>; |
| |
| vcc-supply = <&pm8916_l17>; |
| iovcc-supply = <&pm8916_l6>; |
| |
| touchscreen-size-x = <800>; |
| touchscreen-size-y = <500>; |
| touchscreen-inverted-x; |
| touchscreen-swapped-x-y; |
| |
| pinctrl-0 = <&touchscreen_default>; |
| pinctrl-names = "default"; |
| }; |
| }; |
| |
| &blsp_uart2 { |
| status = "okay"; |
| }; |
| |
| &mpss_mem { |
| reg = <0x0 0x86800000 0x0 0x5000000>; |
| }; |
| |
| &pm8916_bms { |
| monitored-battery = <&battery>; |
| status = "okay"; |
| }; |
| |
| &pm8916_codec { |
| qcom,micbias-lvl = <2800>; |
| qcom,mbhc-vthreshold-low = <150 180 237 450 500>; |
| qcom,mbhc-vthreshold-high = <150 180 237 450 500>; |
| qcom,hphl-jack-type-normally-open; |
| }; |
| |
| &pm8916_resin { |
| linux,code = <KEY_VOLUMEDOWN>; |
| status = "okay"; |
| }; |
| |
| &pm8916_rpm_regulators { |
| pm8916_l17: l17 { |
| regulator-min-microvolt = <2850000>; |
| regulator-max-microvolt = <2850000>; |
| }; |
| }; |
| |
| &pm8916_vib { |
| status = "okay"; |
| }; |
| |
| &sdhc_1 { |
| status = "okay"; |
| }; |
| |
| &sdhc_2 { |
| pinctrl-0 = <&sdc2_default &sdc2_cd_default>; |
| pinctrl-1 = <&sdc2_sleep &sdc2_cd_default>; |
| pinctrl-names = "default", "sleep"; |
| |
| cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>; |
| |
| status = "okay"; |
| }; |
| |
| &sound { |
| model = "msm8916-1mic"; |
| audio-routing = |
| "AMIC1", "MIC BIAS External1", |
| "AMIC2", "MIC BIAS Internal2", |
| "AMIC3", "MIC BIAS External1"; |
| }; |
| |
| &usb { |
| extcon = <&usb_id>, <&usb_id>; |
| status = "okay"; |
| }; |
| |
| &usb_hs_phy { |
| extcon = <&usb_id>; |
| }; |
| |
| &venus { |
| status = "okay"; |
| }; |
| |
| &venus_mem { |
| status = "okay"; |
| }; |
| |
| &wcnss { |
| status = "okay"; |
| }; |
| |
| &wcnss_iris { |
| compatible = "qcom,wcn3620"; |
| }; |
| |
| &wcnss_mem { |
| status = "okay"; |
| }; |
| |
| &tlmm { |
| camera_flash_default: camera-flash-default-state { |
| pins = "gpio31", "gpio32"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| gpio_keys_default: gpio-keys-default-state { |
| pins = "gpio107"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| gpio_leds_default: gpio-led-default-state { |
| pins = "gpio117", "gpio118"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| sdc2_cd_default: sdc2-cd-default-state { |
| pins = "gpio38"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| touchscreen_default: touchscreen-default-state { |
| reset-pins { |
| pins = "gpio12"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| touchscreen-pins { |
| pins = "gpio13"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| }; |
| |
| usb_id_default: usb-id-default-state { |
| pins = "gpio110"; |
| function = "gpio"; |
| drive-strength = <8>; |
| bias-pull-up; |
| }; |
| }; |