| // SPDX-License-Identifier: BSD-3-Clause |
| /* |
| * Copyright (c) 2016-2022, AngeloGioacchino Del Regno |
| * <angelogioacchino.delregno@collabora.com> |
| * Copyright (c) 2022, Konrad Dybcio <konrad.dybcio@somainline.org> |
| * Copyright (c) 2022, Marijn Suijten <marijn.suijten@somainline.org> |
| */ |
| |
| #include <dt-bindings/clock/qcom,gcc-msm8976.h> |
| #include <dt-bindings/clock/qcom,rpmcc.h> |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| #include <dt-bindings/interrupt-controller/irq.h> |
| #include <dt-bindings/power/qcom-rpmpd.h> |
| |
| / { |
| interrupt-parent = <&intc>; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| |
| chosen { }; |
| |
| clocks { |
| xo_board: xo-board { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| }; |
| }; |
| |
| cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| CPU0: cpu@0 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a53"; |
| reg = <0x0>; |
| enable-method = "psci"; |
| cpu-idle-states = <&little_cpu_sleep_0>; |
| capacity-dmips-mhz = <573>; |
| next-level-cache = <&l2_0>; |
| #cooling-cells = <2>; |
| }; |
| |
| CPU1: cpu@1 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a53"; |
| reg = <0x1>; |
| enable-method = "psci"; |
| cpu-idle-states = <&little_cpu_sleep_0>; |
| capacity-dmips-mhz = <573>; |
| next-level-cache = <&l2_0>; |
| #cooling-cells = <2>; |
| }; |
| |
| CPU2: cpu@2 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a53"; |
| reg = <0x2>; |
| enable-method = "psci"; |
| cpu-idle-states = <&little_cpu_sleep_0>; |
| capacity-dmips-mhz = <573>; |
| next-level-cache = <&l2_0>; |
| #cooling-cells = <2>; |
| }; |
| |
| CPU3: cpu@3 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a53"; |
| reg = <0x3>; |
| enable-method = "psci"; |
| cpu-idle-states = <&little_cpu_sleep_0>; |
| capacity-dmips-mhz = <573>; |
| next-level-cache = <&l2_0>; |
| #cooling-cells = <2>; |
| }; |
| |
| CPU4: cpu@100 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a72"; |
| reg = <0x100>; |
| enable-method = "psci"; |
| cpu-idle-states = <&big_cpu_sleep_0 &big_cpu_sleep_1>; |
| capacity-dmips-mhz = <1024>; |
| next-level-cache = <&l2_1>; |
| #cooling-cells = <2>; |
| }; |
| |
| CPU5: cpu@101 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a72"; |
| reg = <0x101>; |
| enable-method = "psci"; |
| cpu-idle-states = <&big_cpu_sleep_0 &big_cpu_sleep_1>; |
| capacity-dmips-mhz = <1024>; |
| next-level-cache = <&l2_1>; |
| #cooling-cells = <2>; |
| }; |
| |
| CPU6: cpu@102 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a72"; |
| reg = <0x102>; |
| enable-method = "psci"; |
| cpu-idle-states = <&big_cpu_sleep_0 &big_cpu_sleep_1>; |
| capacity-dmips-mhz = <1024>; |
| next-level-cache = <&l2_1>; |
| #cooling-cells = <2>; |
| }; |
| |
| CPU7: cpu@103 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a72"; |
| reg = <0x103>; |
| enable-method = "psci"; |
| cpu-idle-states = <&big_cpu_sleep_0 &big_cpu_sleep_1>; |
| capacity-dmips-mhz = <1024>; |
| next-level-cache = <&l2_1>; |
| #cooling-cells = <2>; |
| }; |
| |
| cpu-map { |
| cluster0 { |
| core0 { |
| cpu = <&CPU0>; |
| }; |
| |
| core1 { |
| cpu = <&CPU1>; |
| }; |
| |
| core2 { |
| cpu = <&CPU2>; |
| }; |
| |
| core3 { |
| cpu = <&CPU3>; |
| }; |
| }; |
| |
| cluster1 { |
| core0 { |
| cpu = <&CPU4>; |
| }; |
| |
| core1 { |
| cpu = <&CPU5>; |
| }; |
| |
| core2 { |
| cpu = <&CPU6>; |
| }; |
| |
| core3 { |
| cpu = <&CPU7>; |
| }; |
| }; |
| }; |
| |
| idle-states { |
| entry-method = "psci"; |
| |
| little_cpu_sleep_0: cpu-sleep-0-0 { |
| compatible = "arm,idle-state"; |
| idle-state-name = "little-power-collapse"; |
| arm,psci-suspend-param = <0x40000003>; |
| entry-latency-us = <181>; |
| exit-latency-us = <149>; |
| min-residency-us = <703>; |
| local-timer-stop; |
| }; |
| |
| big_cpu_sleep_0: cpu-sleep-1-0 { |
| compatible = "arm,idle-state"; |
| idle-state-name = "big-retention"; |
| arm,psci-suspend-param = <0x00000002>; |
| entry-latency-us = <142>; |
| exit-latency-us = <99>; |
| min-residency-us = <242>; |
| }; |
| |
| big_cpu_sleep_1: cpu-sleep-1-1 { |
| compatible = "arm,idle-state"; |
| idle-state-name = "big-power-collapse"; |
| arm,psci-suspend-param = <0x40000003>; |
| entry-latency-us = <158>; |
| exit-latency-us = <144>; |
| min-residency-us = <863>; |
| local-timer-stop; |
| }; |
| }; |
| |
| l2_0: l2-cache0 { |
| compatible = "cache"; |
| cache-level = <2>; |
| cache-unified; |
| }; |
| |
| l2_1: l2-cache1 { |
| compatible = "cache"; |
| cache-level = <2>; |
| cache-unified; |
| }; |
| }; |
| |
| firmware { |
| scm: scm { |
| compatible = "qcom,scm-msm8976", "qcom,scm"; |
| clocks = <&gcc GCC_CRYPTO_CLK>, |
| <&gcc GCC_CRYPTO_AXI_CLK>, |
| <&gcc GCC_CRYPTO_AHB_CLK>; |
| clock-names = "core", "bus", "iface"; |
| #reset-cells = <1>; |
| |
| qcom,dload-mode = <&tcsr 0x6100>; |
| }; |
| }; |
| |
| memory@80000000 { |
| device_type = "memory"; |
| /* We expect the bootloader to fill in the size */ |
| reg = <0x0 0x80000000 0x0 0x0>; |
| }; |
| |
| pmu-a53 { |
| compatible = "arm,cortex-a53-pmu"; |
| interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; |
| }; |
| |
| pmu_a72: pmu-a72 { |
| compatible = "arm,cortex-a72-pmu"; |
| interrupts = <GIC_PPI 7 (GIC_CPU_MASK_RAW(0xf0) | IRQ_TYPE_LEVEL_HIGH)>; |
| }; |
| |
| |
| psci { |
| compatible = "arm,psci-1.0"; |
| method = "smc"; |
| }; |
| |
| rpm: remoteproc { |
| compatible = "qcom,msm8976-rpm-proc", "qcom,rpm-proc"; |
| |
| smd-edge { |
| interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>; |
| mboxes = <&apcs 0>; |
| qcom,smd-edge = <15>; |
| |
| rpm_requests: rpm-requests { |
| compatible = "qcom,rpm-msm8976", "qcom,smd-rpm"; |
| qcom,smd-channels = "rpm_requests"; |
| |
| rpmcc: clock-controller { |
| compatible = "qcom,rpmcc-msm8976", "qcom,rpmcc"; |
| clocks = <&xo_board>; |
| clock-names = "xo"; |
| #clock-cells = <1>; |
| }; |
| |
| rpmpd: power-controller { |
| compatible = "qcom,msm8976-rpmpd"; |
| #power-domain-cells = <1>; |
| operating-points-v2 = <&rpmpd_opp_table>; |
| |
| rpmpd_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| |
| rpmpd_opp_ret: opp1 { |
| opp-level = <RPM_SMD_LEVEL_RETENTION>; |
| }; |
| |
| rpmpd_opp_ret_plus: opp2 { |
| opp-level = <RPM_SMD_LEVEL_RETENTION_PLUS>; |
| }; |
| |
| rpmpd_opp_min_svs: opp3 { |
| opp-level = <RPM_SMD_LEVEL_MIN_SVS>; |
| }; |
| |
| rpmpd_opp_low_svs: opp4 { |
| opp-level = <RPM_SMD_LEVEL_LOW_SVS>; |
| }; |
| |
| rpmpd_opp_svs: opp5 { |
| opp-level = <RPM_SMD_LEVEL_SVS>; |
| }; |
| |
| rpmpd_opp_svs_plus: opp6 { |
| opp-level = <RPM_SMD_LEVEL_SVS_PLUS>; |
| }; |
| |
| rpmpd_opp_nom: opp7 { |
| opp-level = <RPM_SMD_LEVEL_NOM>; |
| }; |
| |
| rpmpd_opp_nom_plus: opp8 { |
| opp-level = <RPM_SMD_LEVEL_NOM_PLUS>; |
| }; |
| |
| rpmpd_opp_turbo: opp9 { |
| opp-level = <RPM_SMD_LEVEL_TURBO>; |
| }; |
| |
| rpmpd_opp_turbo_no_cpr: opp10 { |
| opp-level = <RPM_SMD_LEVEL_TURBO_NO_CPR>; |
| }; |
| |
| rpmpd_opp_turbo_high: opp111 { |
| opp-level = <RPM_SMD_LEVEL_TURBO_HIGH>; |
| }; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| reserved-memory { |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| ext-region@85b00000 { |
| reg = <0x0 0x85b00000 0x0 0x500000>; |
| no-map; |
| }; |
| |
| smem@86300000 { |
| compatible = "qcom,smem"; |
| reg = <0x0 0x86300000 0x0 0x100000>; |
| no-map; |
| |
| hwlocks = <&tcsr_mutex 3>; |
| qcom,rpm-msg-ram = <&rpm_msg_ram>; |
| }; |
| |
| reserved@86400000 { |
| reg = <0x0 0x86400000 0x0 0x800000>; |
| no-map; |
| }; |
| |
| mpss_mem: mpss@86c00000 { |
| reg = <0x0 0x86c00000 0x0 0x5600000>; |
| no-map; |
| }; |
| |
| lpass_mem: lpass@8c200000 { |
| reg = <0x0 0x8c200000 0x0 0x1000000>; |
| no-map; |
| }; |
| |
| wcnss_fw_mem: wcnss@8d200000 { |
| reg = <0x0 0x8d200000 0x0 0x800000>; |
| no-map; |
| }; |
| |
| venus_mem: memory@8da00000 { |
| reg = <0x0 0x8da00000 0x0 0x2600000>; |
| no-map; |
| }; |
| |
| tz-apps@8dd00000 { |
| reg = <0x0 0x8dd00000 0x0 0x1400000>; |
| no-map; |
| }; |
| }; |
| |
| smp2p-hexagon { |
| compatible = "qcom,smp2p"; |
| interrupts = <GIC_SPI 291 IRQ_TYPE_EDGE_RISING>; |
| mboxes = <&apcs 10>; |
| |
| qcom,local-pid = <0>; |
| qcom,remote-pid = <2>; |
| qcom,smem = <443>, <429>; |
| |
| adsp_smp2p_out: master-kernel { |
| qcom,entry-name = "master-kernel"; |
| |
| #qcom,smem-state-cells = <1>; |
| }; |
| |
| adsp_smp2p_in: slave-kernel { |
| qcom,entry-name = "slave-kernel"; |
| |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| smp2p-modem { |
| compatible = "qcom,smp2p"; |
| interrupts = <GIC_SPI 27 IRQ_TYPE_EDGE_RISING>; |
| mboxes = <&apcs 14>; |
| |
| qcom,local-pid = <0>; |
| qcom,remote-pid = <1>; |
| qcom,smem = <435>, <428>; |
| |
| modem_smp2p_out: master-kernel { |
| qcom,entry-name = "master-kernel"; |
| |
| #qcom,smem-state-cells = <1>; |
| }; |
| |
| modem_smp2p_in: slave-kernel { |
| qcom,entry-name = "slave-kernel"; |
| |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| smp2p-wcnss { |
| compatible = "qcom,smp2p"; |
| interrupts = <GIC_SPI 143 IRQ_TYPE_EDGE_RISING>; |
| mboxes = <&apcs 18>; |
| |
| qcom,local-pid = <0>; |
| qcom,remote-pid = <4>; |
| qcom,smem = <451>, <431>; |
| |
| wcnss_smp2p_out: master-kernel { |
| qcom,entry-name = "master-kernel"; |
| |
| #qcom,smem-state-cells = <1>; |
| }; |
| |
| wcnss_smp2p_in: slave-kernel { |
| qcom,entry-name = "slave-kernel"; |
| |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| smsm { |
| compatible = "qcom,smsm"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| mboxes = <0>, <&apcs 13>, <&apcs 9>, <&apcs 19>; |
| |
| apps_smsm: apps@0 { |
| reg = <0>; |
| #qcom,smem-state-cells = <1>; |
| }; |
| |
| hexagon_smsm: hexagon@1 { |
| reg = <1>; |
| interrupts = <GIC_SPI 290 IRQ_TYPE_EDGE_RISING>; |
| |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| wcnss_smsm: wcnss@6 { |
| reg = <6>; |
| interrupts = <GIC_SPI 144 IRQ_TYPE_EDGE_RISING>; |
| |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| soc: soc@0 { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0 0 0xffffffff>; |
| compatible = "simple-bus"; |
| |
| rng@22000 { |
| compatible = "qcom,prng"; |
| reg = <0x00022000 0x140>; |
| clocks = <&gcc GCC_PRNG_AHB_CLK>; |
| clock-names = "core"; |
| }; |
| |
| rpm_msg_ram: sram@60000 { |
| compatible = "qcom,rpm-msg-ram"; |
| reg = <0x00060000 0x8000>; |
| }; |
| |
| usb_hs_phy: phy@6c000 { |
| compatible = "qcom,usb-hs-28nm-femtophy"; |
| reg = <0x0006c000 0x200>; |
| #phy-cells = <0>; |
| clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>, |
| <&gcc GCC_USB_HS_PHY_CFG_AHB_CLK>, |
| <&gcc GCC_USB2A_PHY_SLEEP_CLK>; |
| clock-names = "ref", "ahb", "sleep"; |
| resets = <&gcc RST_QUSB2_PHY_BCR>, |
| <&gcc RST_USB2_HS_PHY_ONLY_BCR>; |
| reset-names = "phy", "por"; |
| status = "disabled"; |
| }; |
| |
| qfprom: qfprom@a4000 { |
| compatible = "qcom,msm8976-qfprom", "qcom,qfprom"; |
| reg = <0x000a4000 0x1000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| tsens_base1: base1@218 { |
| reg = <0x218 1>; |
| bits = <0 8>; |
| }; |
| |
| tsens_s0_p1: s0-p1@219 { |
| reg = <0x219 0x1>; |
| bits = <0 6>; |
| }; |
| |
| tsens_s0_p2: s0-p2@219 { |
| reg = <0x219 0x2>; |
| bits = <6 6>; |
| }; |
| |
| tsens_s1_p1: s1-p1@21a { |
| reg = <0x21a 0x2>; |
| bits = <4 6>; |
| }; |
| |
| tsens_s1_p2: s1-p2@21b { |
| reg = <0x21b 0x1>; |
| bits = <2 6>; |
| }; |
| |
| tsens_s2_p1: s2-p1@21c { |
| reg = <0x21c 0x1>; |
| bits = <0 6>; |
| }; |
| |
| tsens_s2_p2: s2-p2@21c { |
| reg = <0x21c 0x2>; |
| bits = <6 6>; |
| }; |
| |
| tsens_s3_p1: s3-p1@21d { |
| reg = <0x21d 0x2>; |
| bits = <4 6>; |
| }; |
| |
| tsens_s3_p2: s3-p2@21e { |
| reg = <0x21e 0x1>; |
| bits = <2 6>; |
| }; |
| |
| tsens_base2: base2@220 { |
| reg = <0x220 1>; |
| bits = <0 8>; |
| }; |
| |
| tsens_s4_p1: s4-p1@221 { |
| reg = <0x221 0x1>; |
| bits = <0 6>; |
| }; |
| |
| tsens_s4_p2: s4-p2@221 { |
| reg = <0x221 0x2>; |
| bits = <6 6>; |
| }; |
| |
| tsens_s5_p1: s5-p1@222 { |
| reg = <0x222 0x2>; |
| bits = <4 6>; |
| }; |
| |
| tsens_s5_p2: s5-p2@223 { |
| reg = <0x224 0x1>; |
| bits = <2 6>; |
| }; |
| |
| tsens_s6_p1: s6-p1@224 { |
| reg = <0x224 0x1>; |
| bits = <0 6>; |
| }; |
| |
| tsens_s6_p2: s6-p2@224 { |
| reg = <0x224 0x2>; |
| bits = <6 6>; |
| }; |
| |
| tsens_s7_p1: s7-p1@225 { |
| reg = <0x225 0x2>; |
| bits = <4 6>; |
| }; |
| |
| tsens_s7_p2: s7-p2@226 { |
| reg = <0x226 0x2>; |
| bits = <2 6>; |
| }; |
| |
| tsens_mode: mode@228 { |
| reg = <0x228 1>; |
| bits = <0 3>; |
| }; |
| |
| tsens_s8_p1: s8-p1@228 { |
| reg = <0x228 0x2>; |
| bits = <3 6>; |
| }; |
| |
| tsens_s8_p2: s8-p2@229 { |
| reg = <0x229 0x1>; |
| bits = <1 6>; |
| }; |
| |
| tsens_s9_p1: s9-p1@229 { |
| reg = <0x229 0x2>; |
| bits = <7 6>; |
| }; |
| |
| tsens_s9_p2: s9-p2@22a { |
| reg = <0x22a 0x2>; |
| bits = <5 6>; |
| }; |
| |
| tsens_s10_p1: s10-p1@22b { |
| reg = <0x22b 0x2>; |
| bits = <3 6>; |
| }; |
| |
| tsens_s10_p2: s10-p2@22c { |
| reg = <0x22c 0x1>; |
| bits = <1 6>; |
| }; |
| }; |
| |
| tsens: thermal-sensor@4a9000 { |
| compatible = "qcom,msm8976-tsens", "qcom,tsens-v1"; |
| reg = <0x004a9000 0x1000>, /* TM */ |
| <0x004a8000 0x1000>; /* SROT */ |
| interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "uplow"; |
| nvmem-cells = <&tsens_mode>, |
| <&tsens_base1>, <&tsens_base2>, |
| <&tsens_s0_p1>, <&tsens_s0_p2>, |
| <&tsens_s1_p1>, <&tsens_s1_p2>, |
| <&tsens_s2_p1>, <&tsens_s2_p2>, |
| <&tsens_s3_p1>, <&tsens_s3_p2>, |
| <&tsens_s4_p1>, <&tsens_s4_p2>, |
| <&tsens_s5_p1>, <&tsens_s5_p2>, |
| <&tsens_s6_p1>, <&tsens_s6_p2>, |
| <&tsens_s7_p1>, <&tsens_s7_p2>, |
| <&tsens_s8_p1>, <&tsens_s8_p2>, |
| <&tsens_s9_p1>, <&tsens_s9_p2>, |
| <&tsens_s10_p1>, <&tsens_s10_p2>; |
| nvmem-cell-names = "mode", |
| "base1", "base2", |
| "s0_p1", "s0_p2", |
| "s1_p1", "s1_p2", |
| "s2_p1", "s2_p2", |
| "s3_p1", "s3_p2", |
| "s4_p1", "s4_p2", |
| "s5_p1", "s5_p2", |
| "s6_p1", "s6_p2", |
| "s7_p1", "s7_p2", |
| "s8_p1", "s8_p2", |
| "s9_p1", "s9_p2", |
| "s10_p1", "s10_p2"; |
| #qcom,sensors = <11>; |
| #thermal-sensor-cells = <1>; |
| }; |
| |
| restart@4ab000 { |
| compatible = "qcom,pshold"; |
| reg = <0x004ab000 0x4>; |
| }; |
| |
| tlmm: pinctrl@1000000 { |
| compatible = "qcom,msm8976-pinctrl"; |
| reg = <0x01000000 0x300000>; |
| interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; |
| #gpio-cells = <2>; |
| gpio-controller; |
| gpio-ranges = <&tlmm 0 0 145>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| |
| spi1_default: spi0-default-state { |
| spi-pins { |
| pins = "gpio0", "gpio1", "gpio3"; |
| function = "blsp_spi1"; |
| drive-strength = <12>; |
| bias-disable; |
| }; |
| |
| cs-pins { |
| pins = "gpio2"; |
| function = "blsp_spi1"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| |
| spi1_sleep: spi0-sleep-state { |
| spi-pins { |
| pins = "gpio0", "gpio1", "gpio3"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-down; |
| }; |
| |
| cs-pins { |
| pins = "gpio2"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| |
| blsp1_i2c2_default: blsp1-i2c2-default-state { |
| pins = "gpio6", "gpio7"; |
| function = "blsp_i2c2"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| blsp1_i2c2_sleep: blsp1-i2c2-sleep-state { |
| pins = "gpio6", "gpio7"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| blsp1_i2c4_default: blsp1-i2c4-default-state { |
| pins = "gpio14", "gpio15"; |
| function = "blsp_i2c4"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| blsp1_i2c4_sleep: blsp1-i2c4-sleep-state { |
| pins = "gpio14", "gpio15"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| blsp2_uart2_active: blsp2-uart2-active-state { |
| pins = "gpio20", "gpio21"; |
| function = "blsp_uart6"; |
| drive-strength = <4>; |
| bias-disable; |
| }; |
| |
| blsp2_uart2_sleep: blsp2-uart2-sleep-state { |
| pins = "gpio20", "gpio21"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| /* 4 (not 6!) interfaces per QUP, BLSP2 indexes are numbered (n)+4 */ |
| blsp2_i2c2_default: blsp2-i2c2-default-state { |
| pins = "gpio22", "gpio23"; |
| function = "blsp_i2c6"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| blsp2_i2c2_sleep: blsp2-i2c2-sleep-state { |
| pins = "gpio22", "gpio23"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| blsp2_i2c4_default: blsp2-i2c4-default-state { |
| pins = "gpio18", "gpio19"; |
| function = "blsp_i2c8"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| blsp2_i2c4_sleep: blsp2-i2c4-sleep-state { |
| pins = "gpio18", "gpio19"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| wcss_wlan_default: wcss-wlan-default-state { |
| wcss-wlan2-pins { |
| pins = "gpio40"; |
| function = "wcss_wlan2"; |
| drive-strength = <6>; |
| bias-pull-up; |
| }; |
| |
| wcss-wlan1-pins { |
| pins = "gpio41"; |
| function = "wcss_wlan1"; |
| drive-strength = <6>; |
| bias-pull-up; |
| }; |
| |
| wcss-wlan0-pins { |
| pins = "gpio42"; |
| function = "wcss_wlan0"; |
| drive-strength = <6>; |
| bias-pull-up; |
| }; |
| |
| wcss-wlan-pins { |
| pins = "gpio43", "gpio44"; |
| function = "wcss_wlan"; |
| drive-strength = <6>; |
| bias-pull-up; |
| }; |
| }; |
| }; |
| |
| gcc: clock-controller@1800000 { |
| compatible = "qcom,gcc-msm8976"; |
| reg = <0x01800000 0x80000>; |
| #clock-cells = <1>; |
| #reset-cells = <1>; |
| #power-domain-cells = <1>; |
| |
| assigned-clocks = <&gcc GPLL3>; |
| assigned-clock-rates = <1100000000>; |
| |
| clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>, |
| <&rpmcc RPM_SMD_XO_A_CLK_SRC>, |
| <&mdss_dsi0_phy 1>, |
| <&mdss_dsi0_phy 0>, |
| <&mdss_dsi1_phy 1>, |
| <&mdss_dsi1_phy 0>; |
| clock-names = "xo", |
| "xo_a", |
| "dsi0pll", |
| "dsi0pllbyte", |
| "dsi1pll", |
| "dsi1pllbyte"; |
| }; |
| |
| tcsr_mutex: hwlock@1905000 { |
| compatible = "qcom,tcsr-mutex"; |
| reg = <0x01905000 0x20000>; |
| #hwlock-cells = <1>; |
| }; |
| |
| tcsr: syscon@1937000 { |
| compatible = "qcom,msm8976-tcsr", "syscon"; |
| reg = <0x01937000 0x30000>; |
| }; |
| |
| mdss: display-subsystem@1a00000 { |
| compatible = "qcom,mdss"; |
| |
| reg = <0x01a00000 0x1000>, |
| <0x01ab0000 0x3000>; |
| reg-names = "mdss_phys", "vbif_phys"; |
| |
| power-domains = <&gcc MDSS_GDSC>; |
| interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>; |
| |
| interrupt-controller; |
| #interrupt-cells = <1>; |
| |
| clocks = <&gcc GCC_MDSS_AHB_CLK>, |
| <&gcc GCC_MDSS_AXI_CLK>, |
| <&gcc GCC_MDSS_VSYNC_CLK>, |
| <&gcc GCC_MDSS_MDP_CLK>; |
| clock-names = "iface", |
| "bus", |
| "vsync", |
| "core"; |
| |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| status = "disabled"; |
| |
| mdss_mdp: display-controller@1a01000 { |
| compatible = "qcom,msm8976-mdp5", "qcom,mdp5"; |
| reg = <0x01a01000 0x89000>; |
| reg-names = "mdp_phys"; |
| |
| interrupt-parent = <&mdss>; |
| interrupts = <0>; |
| |
| clocks = <&gcc GCC_MDSS_AHB_CLK>, |
| <&gcc GCC_MDSS_AXI_CLK>, |
| <&gcc GCC_MDSS_MDP_CLK>, |
| <&gcc GCC_MDSS_VSYNC_CLK>, |
| <&gcc GCC_MDP_TBU_CLK>, |
| <&gcc GCC_MDP_RT_TBU_CLK>; |
| clock-names = "iface", |
| "bus", |
| "core", |
| "vsync", |
| "tbu", |
| "tbu_rt"; |
| |
| operating-points-v2 = <&mdp_opp_table>; |
| power-domains = <&gcc MDSS_GDSC>; |
| |
| iommus = <&apps_iommu 22>; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| mdss_mdp5_intf1_out: endpoint { |
| remote-endpoint = <&mdss_dsi0_in>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| mdss_mdp5_intf2_out: endpoint { |
| remote-endpoint = <&mdss_dsi1_in>; |
| }; |
| }; |
| }; |
| |
| mdp_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| |
| opp-177780000 { |
| opp-hz = /bits/ 64 <177780000>; |
| required-opps = <&rpmpd_opp_svs>; |
| }; |
| |
| opp-270000000 { |
| opp-hz = /bits/ 64 <270000000>; |
| required-opps = <&rpmpd_opp_svs_plus>; |
| }; |
| |
| opp-320000000 { |
| opp-hz = /bits/ 64 <320000000>; |
| required-opps = <&rpmpd_opp_nom>; |
| }; |
| |
| opp-360000000 { |
| opp-hz = /bits/ 64 <360000000>; |
| required-opps = <&rpmpd_opp_turbo>; |
| }; |
| }; |
| }; |
| |
| mdss_dsi0: dsi@1a94000 { |
| compatible = "qcom,msm8976-dsi-ctrl", "qcom,mdss-dsi-ctrl"; |
| reg = <0x01a94000 0x300>; |
| reg-names = "dsi_ctrl"; |
| |
| interrupt-parent = <&mdss>; |
| interrupts = <4>; |
| |
| clocks = <&gcc GCC_MDSS_MDP_CLK>, |
| <&gcc GCC_MDSS_AHB_CLK>, |
| <&gcc GCC_MDSS_AXI_CLK>, |
| <&gcc GCC_MDSS_BYTE0_CLK>, |
| <&gcc GCC_MDSS_PCLK0_CLK>, |
| <&gcc GCC_MDSS_ESC0_CLK>; |
| clock-names = "mdp_core", |
| "iface", |
| "bus", |
| "byte", |
| "pixel", |
| "core"; |
| |
| assigned-clocks = <&gcc GCC_MDSS_BYTE0_CLK_SRC>, |
| <&gcc GCC_MDSS_PCLK0_CLK_SRC>; |
| assigned-clock-parents = <&mdss_dsi0_phy 0>, |
| <&mdss_dsi0_phy 1>; |
| |
| phys = <&mdss_dsi0_phy>; |
| |
| operating-points-v2 = <&dsi0_opp_table>; |
| power-domains = <&gcc MDSS_GDSC>; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| mdss_dsi0_in: endpoint { |
| remote-endpoint = <&mdss_mdp5_intf1_out>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| mdss_dsi0_out: endpoint { |
| }; |
| }; |
| }; |
| |
| dsi0_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| |
| opp-125000000 { |
| opp-hz = /bits/ 64 <125000000>; |
| required-opps = <&rpmpd_opp_svs>; |
| }; |
| |
| opp-161250000 { |
| opp-hz = /bits/ 64 <161250000>; |
| required-opps = <&rpmpd_opp_svs_plus>; |
| }; |
| |
| opp-187500000 { |
| opp-hz = /bits/ 64 <187500000>; |
| required-opps = <&rpmpd_opp_nom>; |
| }; |
| }; |
| }; |
| |
| mdss_dsi1: dsi@1a96000 { |
| compatible = "qcom,msm8976-dsi-ctrl", "qcom,mdss-dsi-ctrl"; |
| reg = <0x01a96000 0x300>; |
| reg-names = "dsi_ctrl"; |
| |
| interrupt-parent = <&mdss>; |
| interrupts = <5>; |
| |
| clocks = <&gcc GCC_MDSS_MDP_CLK>, |
| <&gcc GCC_MDSS_AHB_CLK>, |
| <&gcc GCC_MDSS_AXI_CLK>, |
| <&gcc GCC_MDSS_BYTE1_CLK>, |
| <&gcc GCC_MDSS_PCLK1_CLK>, |
| <&gcc GCC_MDSS_ESC1_CLK>; |
| clock-names = "mdp_core", |
| "iface", |
| "bus", |
| "byte", |
| "pixel", |
| "core"; |
| |
| assigned-clocks = <&gcc GCC_MDSS_BYTE1_CLK_SRC>, |
| <&gcc GCC_MDSS_PCLK1_CLK_SRC>; |
| assigned-clock-parents = <&mdss_dsi1_phy 0>, |
| <&mdss_dsi1_phy 1>; |
| |
| phys = <&mdss_dsi1_phy>; |
| |
| operating-points-v2 = <&dsi0_opp_table>; |
| power-domains = <&gcc MDSS_GDSC>; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| mdss_dsi1_in: endpoint { |
| remote-endpoint = <&mdss_mdp5_intf2_out>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| mdss_dsi1_out: endpoint { |
| }; |
| }; |
| }; |
| }; |
| |
| mdss_dsi0_phy: phy@1a94a00 { |
| compatible = "qcom,dsi-phy-28nm-hpm-fam-b"; |
| reg = <0x01a94a00 0xd4>, |
| <0x01a94400 0x280>, |
| <0x01a94b80 0x30>; |
| reg-names = "dsi_pll", |
| "dsi_phy", |
| "dsi_phy_regulator"; |
| |
| #clock-cells = <1>; |
| #phy-cells = <0>; |
| |
| clocks = <&gcc GCC_MDSS_AHB_CLK>, |
| <&rpmcc RPM_SMD_XO_CLK_SRC>; |
| clock-names = "iface", "ref"; |
| |
| status = "disabled"; |
| }; |
| |
| mdss_dsi1_phy: phy@1a96a00 { |
| compatible = "qcom,dsi-phy-28nm-hpm-fam-b"; |
| reg = <0x01a96a00 0xd4>, |
| <0x01a96400 0x280>, |
| <0x01a96b80 0x30>; |
| reg-names = "dsi_pll", |
| "dsi_phy", |
| "dsi_phy_regulator"; |
| |
| #clock-cells = <1>; |
| #phy-cells = <0>; |
| |
| clocks = <&gcc GCC_MDSS_AHB_CLK>, |
| <&rpmcc RPM_SMD_XO_CLK_SRC>; |
| clock-names = "iface", "ref"; |
| |
| status = "disabled"; |
| }; |
| }; |
| |
| adreno_gpu: gpu@1c00000 { |
| compatible = "qcom,adreno-510.0", "qcom,adreno"; |
| |
| reg = <0x01c00000 0x40000>; |
| reg-names = "kgsl_3d0_reg_memory"; |
| |
| interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "kgsl_3d0_irq"; |
| |
| clocks = <&gcc GCC_GFX3D_OXILI_CLK>, |
| <&gcc GCC_GFX3D_OXILI_AHB_CLK>, |
| <&gcc GCC_GFX3D_OXILI_GMEM_CLK>, |
| <&gcc GCC_GFX3D_BIMC_CLK>, |
| <&gcc GCC_GFX3D_OXILI_TIMER_CLK>, |
| <&gcc GCC_GFX3D_OXILI_AON_CLK>; |
| clock-names = "core", |
| "iface", |
| "mem", |
| "mem_iface", |
| "rbbmtimer", |
| "alwayson"; |
| |
| power-domains = <&gcc OXILI_GX_GDSC>; |
| |
| iommus = <&gpu_iommu 0>; |
| |
| operating-points-v2 = <&gpu_opp_table>; |
| |
| status = "disabled"; |
| |
| gpu_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| |
| opp-200000000 { |
| opp-hz = /bits/ 64 <200000000>; |
| required-opps = <&rpmpd_opp_low_svs>; |
| opp-supported-hw = <0xff>; |
| }; |
| |
| opp-300000000 { |
| opp-hz = /bits/ 64 <300000000>; |
| required-opps = <&rpmpd_opp_svs>; |
| opp-supported-hw = <0xff>; |
| }; |
| |
| opp-400000000 { |
| opp-hz = /bits/ 64 <400000000>; |
| required-opps = <&rpmpd_opp_nom>; |
| opp-supported-hw = <0xff>; |
| }; |
| |
| opp-480000000 { |
| opp-hz = /bits/ 64 <480000000>; |
| required-opps = <&rpmpd_opp_nom_plus>; |
| opp-supported-hw = <0xff>; |
| }; |
| |
| opp-540000000 { |
| opp-hz = /bits/ 64 <540000000>; |
| required-opps = <&rpmpd_opp_turbo>; |
| opp-supported-hw = <0xff>; |
| }; |
| |
| opp-600000000 { |
| opp-hz = /bits/ 64 <600000000>; |
| required-opps = <&rpmpd_opp_turbo>; |
| opp-supported-hw = <0xff>; |
| }; |
| }; |
| }; |
| |
| apps_iommu: iommu@1ee0000 { |
| compatible = "qcom,msm8976-iommu", "qcom,msm-iommu-v2"; |
| reg = <0x01ee0000 0x3000>; |
| ranges = <0 0x01e20000 0x20000>; |
| |
| clocks = <&gcc GCC_SMMU_CFG_CLK>, |
| <&gcc GCC_APSS_TCU_CLK>; |
| clock-names = "iface", "bus"; |
| |
| qcom,iommu-secure-id = <17>; |
| |
| #address-cells = <1>; |
| #size-cells = <1>; |
| #iommu-cells = <1>; |
| |
| /* VFE */ |
| iommu-ctx@15000 { |
| compatible = "qcom,msm-iommu-v2-ns"; |
| reg = <0x15000 0x1000>; |
| qcom,ctx-asid = <20>; |
| interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| /* VENUS NS */ |
| iommu-ctx@16000 { |
| compatible = "qcom,msm-iommu-v2-ns"; |
| reg = <0x16000 0x1000>; |
| qcom,ctx-asid = <21>; |
| interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| /* MDP0 */ |
| iommu-ctx@17000 { |
| compatible = "qcom,msm-iommu-v2-ns"; |
| reg = <0x17000 0x1000>; |
| qcom,ctx-asid = <22>; |
| interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| }; |
| |
| gpu_iommu: iommu@1f08000 { |
| compatible = "qcom,msm8976-iommu", "qcom,msm-iommu-v2"; |
| ranges = <0 0x01f08000 0x8000>; |
| |
| clocks = <&gcc GCC_SMMU_CFG_CLK>, |
| <&gcc GCC_GFX3D_TCU_CLK>; |
| clock-names = "iface", "bus"; |
| |
| power-domains = <&gcc OXILI_CX_GDSC>; |
| |
| qcom,iommu-secure-id = <18>; |
| |
| #address-cells = <1>; |
| #size-cells = <1>; |
| #iommu-cells = <1>; |
| |
| /* gfx3d user */ |
| iommu-ctx@0 { |
| compatible = "qcom,msm-iommu-v2-ns"; |
| reg = <0x0 0x1000>; |
| qcom,ctx-asid = <0>; |
| interrupts = <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| /* gfx3d secure */ |
| iommu-ctx@1000 { |
| compatible = "qcom,msm-iommu-v2-sec"; |
| reg = <0x1000 0x1000>; |
| qcom,ctx-asid = <2>; |
| interrupts = <GIC_SPI 241 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| /* gfx3d priv */ |
| iommu-ctx@2000 { |
| compatible = "qcom,msm-iommu-v2-sec"; |
| reg = <0x2000 0x1000>; |
| qcom,ctx-asid = <1>; |
| interrupts = <GIC_SPI 242 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| }; |
| |
| spmi_bus: spmi@200f000 { |
| compatible = "qcom,spmi-pmic-arb"; |
| reg = <0x0200f000 0x1000>, |
| <0x02400000 0x800000>, |
| <0x02c00000 0x800000>, |
| <0x03800000 0x200000>, |
| <0x0200a000 0x2100>; |
| reg-names = "core", "chnls", "obsrvr", "intr", "cnfg"; |
| interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "periph_irq"; |
| qcom,channel = <0>; |
| qcom,ee = <0>; |
| |
| #address-cells = <2>; |
| #size-cells = <0>; |
| interrupt-controller; |
| #interrupt-cells = <4>; |
| }; |
| |
| sdhc_1: mmc@7824900 { |
| compatible = "qcom,msm8976-sdhci", "qcom,sdhci-msm-v4"; |
| reg = <0x07824900 0x500>, <0x07824000 0x800>; |
| reg-names = "hc", "core"; |
| |
| interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "hc_irq", "pwr_irq"; |
| |
| clocks = <&gcc GCC_SDCC1_AHB_CLK>, |
| <&gcc GCC_SDCC1_APPS_CLK>, |
| <&rpmcc RPM_SMD_XO_CLK_SRC>; |
| clock-names = "iface", "core", "xo"; |
| status = "disabled"; |
| }; |
| |
| sdhc_2: mmc@7864900 { |
| compatible = "qcom,msm8976-sdhci", "qcom,sdhci-msm-v4"; |
| reg = <0x07864900 0x11c>, <0x07864000 0x800>; |
| reg-names = "hc", "core"; |
| |
| interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "hc_irq", "pwr_irq"; |
| |
| clocks = <&gcc GCC_SDCC2_AHB_CLK>, |
| <&gcc GCC_SDCC2_APPS_CLK>, |
| <&rpmcc RPM_SMD_XO_CLK_SRC>; |
| clock-names = "iface", "core", "xo"; |
| status = "disabled"; |
| }; |
| |
| blsp1_dma: dma-controller@7884000 { |
| compatible = "qcom,bam-v1.7.0"; |
| reg = <0x07884000 0x1f000>; |
| interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GCC_BLSP1_AHB_CLK>; |
| clock-names = "bam_clk"; |
| #dma-cells = <1>; |
| qcom,ee = <0>; |
| }; |
| |
| blsp1_uart1: serial@78af000 { |
| compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; |
| reg = <0x078af000 0x200>; |
| interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>; |
| clock-names = "core", "iface"; |
| dmas = <&blsp1_dma 0>, <&blsp1_dma 1>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| blsp1_uart2: serial@78b0000 { |
| compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; |
| reg = <0x078b0000 0x200>; |
| interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>; |
| clock-names = "core", "iface"; |
| dmas = <&blsp1_dma 2>, <&blsp1_dma 3>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| blsp1_spi1: spi@78b5000 { |
| compatible = "qcom,spi-qup-v2.2.1"; |
| reg = <0x078b5000 0x500>; |
| interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GCC_BLSP1_QUP1_SPI_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>; |
| clock-names = "core", "iface"; |
| dmas = <&blsp1_dma 4>, <&blsp1_dma 5>; |
| dma-names = "tx", "rx"; |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&spi1_default>; |
| pinctrl-1 = <&spi1_sleep>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| blsp1_i2c2: i2c@78b6000 { |
| compatible = "qcom,i2c-qup-v2.2.1"; |
| reg = <0x078b6000 0x500>; |
| interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>; |
| clock-names = "core", "iface"; |
| clock-frequency = <400000>; |
| dmas = <&blsp1_dma 6>, <&blsp1_dma 7>; |
| dma-names = "tx", "rx"; |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&blsp1_i2c2_default>; |
| pinctrl-1 = <&blsp1_i2c2_default>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| blsp1_i2c4: i2c@78b8000 { |
| compatible = "qcom,i2c-qup-v2.2.1"; |
| reg = <0x078b8000 0x500>; |
| interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>; |
| clock-names = "core", "iface"; |
| clock-frequency = <400000>; |
| dmas = <&blsp1_dma 10>, <&blsp1_dma 11>; |
| dma-names = "tx", "rx"; |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&blsp1_i2c4_default>; |
| pinctrl-1 = <&blsp1_i2c4_sleep>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| otg: usb@78db000 { |
| compatible = "qcom,ci-hdrc"; |
| reg = <0x078db000 0x200>, |
| <0x078db200 0x200>; |
| interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GCC_USB_HS_AHB_CLK>, <&gcc GCC_USB_HS_SYSTEM_CLK>; |
| clock-names = "iface", "core"; |
| assigned-clocks = <&gcc GCC_USB_HS_SYSTEM_CLK>; |
| assigned-clock-rates = <80000000>; |
| resets = <&gcc RST_USB_HS_BCR>; |
| reset-names = "core"; |
| ahb-burst-config = <0>; |
| dr_mode = "peripheral"; |
| phy_type = "ulpi"; |
| phy-names = "usb-phy"; |
| phys = <&usb_hs_phy>; |
| status = "disabled"; |
| #reset-cells = <1>; |
| }; |
| |
| sdhc_3: mmc@7a24900 { |
| compatible = "qcom,msm8976-sdhci", "qcom,sdhci-msm-v4"; |
| reg = <0x07a24900 0x11c>, <0x07a24000 0x800>; |
| reg-names = "hc", "core"; |
| |
| interrupts = <GIC_SPI 295 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "hc_irq", "pwr_irq"; |
| |
| clocks = <&gcc GCC_SDCC3_AHB_CLK>, |
| <&gcc GCC_SDCC3_APPS_CLK>, |
| <&rpmcc RPM_SMD_XO_CLK_SRC>; |
| clock-names = "iface", "core", "xo"; |
| |
| status = "disabled"; |
| }; |
| |
| blsp2_dma: dma-controller@7ac4000 { |
| compatible = "qcom,bam-v1.7.0"; |
| reg = <0x07ac4000 0x1f000>; |
| interrupts = <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GCC_BLSP2_AHB_CLK>; |
| clock-names = "bam_clk"; |
| #dma-cells = <1>; |
| qcom,ee = <0>; |
| }; |
| |
| blsp2_uart2: serial@7af0000 { |
| compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; |
| reg = <0x07af0000 0x200>; |
| interrupts = <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GCC_BLSP2_UART2_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>; |
| clock-names = "core", "iface"; |
| dmas = <&blsp2_dma 0>, <&blsp2_dma 1>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| blsp2_i2c2: i2c@7af6000 { |
| compatible = "qcom,i2c-qup-v2.2.1"; |
| reg = <0x07af6000 0x600>; |
| interrupts = <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GCC_BLSP2_QUP2_I2C_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>; |
| clock-names = "core", "iface"; |
| clock-frequency = <400000>; |
| dmas = <&blsp2_dma 6>, <&blsp2_dma 7>; |
| dma-names = "tx", "rx"; |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&blsp2_i2c2_default>; |
| pinctrl-1 = <&blsp2_i2c2_sleep>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| blsp2_i2c4: i2c@7af8000 { |
| compatible = "qcom,i2c-qup-v2.2.1"; |
| reg = <0x07af8000 0x600>; |
| interrupts = <GIC_SPI 302 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GCC_BLSP2_QUP4_I2C_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>; |
| clock-names = "core", "iface"; |
| clock-frequency = <400000>; |
| dmas = <&blsp2_dma 10>, <&blsp2_dma 11>; |
| dma-names = "tx", "rx"; |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&blsp2_i2c4_default>; |
| pinctrl-1 = <&blsp2_i2c4_sleep>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| wcnss: remoteproc@a204000 { |
| compatible = "qcom,pronto-v3-pil", "qcom,pronto"; |
| reg = <0x0a204000 0x2000>, |
| <0x0a202000 0x1000>, |
| <0x0a21b000 0x3000>; |
| reg-names = "ccu", |
| "dxe", |
| "pmu"; |
| |
| memory-region = <&wcnss_fw_mem>; |
| |
| interrupts-extended = <&intc GIC_SPI 149 IRQ_TYPE_EDGE_RISING>, |
| <&wcnss_smp2p_in 0 IRQ_TYPE_EDGE_RISING>, |
| <&wcnss_smp2p_in 1 IRQ_TYPE_EDGE_RISING>, |
| <&wcnss_smp2p_in 2 IRQ_TYPE_EDGE_RISING>, |
| <&wcnss_smp2p_in 3 IRQ_TYPE_EDGE_RISING>; |
| interrupt-names = "wdog", |
| "fatal", |
| "ready", |
| "handover", |
| "stop-ack"; |
| |
| power-domains = <&rpmpd MSM8976_VDDCX>, |
| <&rpmpd MSM8976_VDDMX>; |
| power-domain-names = "cx", "mx"; |
| |
| qcom,smem-states = <&wcnss_smp2p_out 0>; |
| qcom,smem-state-names = "stop"; |
| |
| pinctrl-0 = <&wcss_wlan_default>; |
| pinctrl-names = "default"; |
| |
| status = "disabled"; |
| |
| wcnss_iris: iris { |
| /* Separate chip, compatible is board-specific */ |
| clocks = <&rpmcc RPM_SMD_RF_CLK2>; |
| clock-names = "xo"; |
| }; |
| |
| smd-edge { |
| interrupts = <GIC_SPI 142 IRQ_TYPE_EDGE_RISING>; |
| |
| mboxes = <&apcs 17>; |
| qcom,smd-edge = <6>; |
| qcom,remote-pid = <4>; |
| |
| label = "pronto"; |
| |
| wcnss_ctrl: wcnss { |
| compatible = "qcom,wcnss"; |
| qcom,smd-channels = "WCNSS_CTRL"; |
| |
| qcom,mmio = <&wcnss>; |
| |
| wcnss_bt: bluetooth { |
| compatible = "qcom,wcnss-bt"; |
| }; |
| |
| wcnss_wifi: wifi { |
| compatible = "qcom,wcnss-wlan"; |
| |
| interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "tx", "rx"; |
| |
| qcom,smem-states = <&apps_smsm 10>, |
| <&apps_smsm 9>; |
| qcom,smem-state-names = "tx-enable", |
| "tx-rings-empty"; |
| }; |
| }; |
| }; |
| }; |
| |
| intc: interrupt-controller@b000000 { |
| compatible = "qcom,msm-qgic2"; |
| reg = <0x0b000000 0x1000>, <0x0b002000 0x1000>; |
| interrupt-controller; |
| #interrupt-cells = <3>; |
| }; |
| |
| apcs: mailbox@b011000 { |
| compatible = "qcom,msm8976-apcs-kpss-global", |
| "qcom,msm8994-apcs-kpss-global", "syscon"; |
| reg = <0x0b011000 0x1000>; |
| #mbox-cells = <1>; |
| }; |
| |
| timer@b120000 { |
| compatible = "arm,armv7-timer-mem"; |
| reg = <0x0b120000 0x1000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| clock-frequency = <19200000>; |
| |
| frame@b121000 { |
| reg = <0x0b121000 0x1000>, <0x0b122000 0x1000>; |
| interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; |
| frame-number = <0>; |
| }; |
| |
| frame@b123000 { |
| reg = <0x0b123000 0x1000>; |
| interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; |
| frame-number = <1>; |
| status = "disabled"; |
| }; |
| |
| frame@b124000 { |
| reg = <0x0b124000 0x1000>; |
| interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; |
| frame-number = <2>; |
| status = "disabled"; |
| }; |
| |
| frame@b125000 { |
| reg = <0x0b125000 0x1000>; |
| interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; |
| frame-number = <3>; |
| status = "disabled"; |
| }; |
| |
| frame@b126000 { |
| reg = <0x0b126000 0x1000>; |
| interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; |
| frame-number = <4>; |
| status = "disabled"; |
| }; |
| |
| frame@b127000 { |
| reg = <0x0b127000 0x1000>; |
| interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; |
| frame-number = <5>; |
| status = "disabled"; |
| }; |
| |
| frame@b128000 { |
| reg = <0x0b128000 0x1000>; |
| interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; |
| frame-number = <6>; |
| status = "disabled"; |
| }; |
| }; |
| |
| imem: sram@8600000 { |
| compatible = "qcom,msm8976-imem", "syscon", "simple-mfd"; |
| reg = <0x08600000 0x1000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| ranges = <0 0x08600000 0x1000>; |
| |
| pil-reloc@94c { |
| compatible = "qcom,pil-reloc-info"; |
| reg = <0x94c 0xc8>; |
| }; |
| }; |
| }; |
| |
| thermal-zones { |
| aoss0-thermal { |
| polling-delay-passive = <250>; |
| |
| thermal-sensors = <&tsens 0>; |
| |
| trips { |
| aoss0_alert0: trip-point0 { |
| temperature = <75000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| modem-thermal { |
| polling-delay-passive = <250>; |
| |
| thermal-sensors = <&tsens 1>; |
| trips { |
| modem_alert0: trip-point0 { |
| temperature = <75000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| qdsp-thermal { |
| polling-delay-passive = <250>; |
| |
| thermal-sensors = <&tsens 2>; |
| trips { |
| qdsp_alert0: trip-point0 { |
| temperature = <75000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| cam-isp-thermal { |
| polling-delay-passive = <250>; |
| |
| thermal-sensors = <&tsens 3>; |
| trips { |
| cam_isp_alert0: trip-point0 { |
| temperature = <75000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| cpu4-thermal { |
| polling-delay-passive = <250>; |
| |
| thermal-sensors = <&tsens 4>; |
| |
| trips { |
| cpu4_alert0: trip-point0 { |
| temperature = <50000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| cpu4_alert1: trip-point1 { |
| temperature = <55000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| cpu4_crit: cpu-crit { |
| temperature = <75000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu5-thermal { |
| polling-delay-passive = <250>; |
| |
| thermal-sensors = <&tsens 5>; |
| |
| trips { |
| cpu5_alert0: trip-point0 { |
| temperature = <50000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| cpu5_alert1: trip-point1 { |
| temperature = <55000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| cpu5_crit: cpu-crit { |
| temperature = <75000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu6-thermal { |
| polling-delay-passive = <250>; |
| |
| thermal-sensors = <&tsens 6>; |
| |
| trips { |
| cpu6_alert0: trip-point0 { |
| temperature = <50000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| cpu6_alert1: trip-point1 { |
| temperature = <55000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| cpu6_crit: cpu-crit { |
| temperature = <75000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu7-thermal { |
| polling-delay-passive = <250>; |
| |
| thermal-sensors = <&tsens 7>; |
| |
| trips { |
| cpu7_alert0: trip-point0 { |
| temperature = <50000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| cpu7_alert1: trip-point1 { |
| temperature = <55000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| cpu7_crit: cpu-crit { |
| temperature = <75000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| big-l2-thermal { |
| polling-delay-passive = <250>; |
| |
| thermal-sensors = <&tsens 8>; |
| |
| trips { |
| l2_alert0: trip-point0 { |
| temperature = <50000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| l2_alert1: trip-point1 { |
| temperature = <55000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| l2_crit: l2-crit { |
| temperature = <75000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu0-thermal { |
| polling-delay-passive = <250>; |
| |
| thermal-sensors = <&tsens 9>; |
| |
| trips { |
| cpu0_alert0: trip-point0 { |
| temperature = <50000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| cpu0_alert1: trip-point1 { |
| temperature = <55000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| cpu0_crit: cpu-crit { |
| temperature = <75000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| gpu-thermal { |
| polling-delay-passive = <250>; |
| |
| thermal-sensors = <&tsens 10>; |
| |
| trips { |
| gpu_alert0: trip-point0 { |
| temperature = <50000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| gpu_alert1: trip-point1 { |
| temperature = <55000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| gpu_crit: gpu-crit { |
| temperature = <75000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| }; |
| |
| timer { |
| compatible = "arm,armv8-timer"; |
| interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>; |
| clock-frequency = <19200000>; |
| }; |
| }; |
