| // SPDX-License-Identifier: BSD-3-Clause |
| /* |
| * Copyright (c) 2023, Linaro Limited |
| */ |
| |
| /dts-v1/; |
| |
| #include <dt-bindings/leds/common.h> |
| #include <dt-bindings/regulator/qcom,rpmh-regulator.h> |
| #include "sm8650.dtsi" |
| #include "pm8010.dtsi" |
| #include "pm8550.dtsi" |
| #include "pm8550b.dtsi" |
| #define PMK8550VE_SID 8 |
| #include "pm8550ve.dtsi" |
| #include "pm8550vs.dtsi" |
| #include "pmk8550.dtsi" |
| #include "pmr735d_a.dtsi" |
| |
| / { |
| model = "Qualcomm Technologies, Inc. SM8650 QRD"; |
| compatible = "qcom,sm8650-qrd", "qcom,sm8650"; |
| |
| aliases { |
| serial0 = &uart15; |
| serial1 = &uart14; |
| }; |
| |
| chosen { |
| stdout-path = "serial0:115200n8"; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| |
| pinctrl-0 = <&volume_up_n>; |
| pinctrl-names = "default"; |
| |
| key-volume-up { |
| label = "Volume Up"; |
| linux,code = <KEY_VOLUMEUP>; |
| gpios = <&pm8550_gpios 6 GPIO_ACTIVE_LOW>; |
| debounce-interval = <15>; |
| linux,can-disable; |
| wakeup-source; |
| }; |
| }; |
| |
| pmic-glink { |
| compatible = "qcom,sm8650-pmic-glink", |
| "qcom,sm8550-pmic-glink", |
| "qcom,pmic-glink"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| orientation-gpios = <&tlmm 29 GPIO_ACTIVE_HIGH>; |
| |
| connector@0 { |
| compatible = "usb-c-connector"; |
| reg = <0>; |
| |
| power-role = "dual"; |
| data-role = "dual"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| pmic_glink_hs_in: endpoint { |
| remote-endpoint = <&usb_1_dwc3_hs>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| pmic_glink_ss_in: endpoint { |
| remote-endpoint = <&redriver_ss_out>; |
| }; |
| }; |
| |
| port@2 { |
| reg = <2>; |
| |
| pmic_glink_sbu: endpoint { |
| remote-endpoint = <&wcd_usbss_sbu_mux>; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| sound { |
| compatible = "qcom,sm8650-sndcard", "qcom,sm8450-sndcard"; |
| model = "SM8650-QRD"; |
| audio-routing = "SpkrLeft IN", "WSA_SPK1 OUT", |
| "SpkrRight IN", "WSA_SPK2 OUT", |
| "IN1_HPHL", "HPHL_OUT", |
| "IN2_HPHR", "HPHR_OUT", |
| "AMIC1", "MIC BIAS1", |
| "AMIC2", "MIC BIAS2", |
| "AMIC3", "MIC BIAS3", |
| "AMIC4", "MIC BIAS3", |
| "AMIC5", "MIC BIAS4", |
| "TX SWR_INPUT0", "ADC1_OUTPUT", |
| "TX SWR_INPUT1", "ADC2_OUTPUT", |
| "TX SWR_INPUT2", "ADC3_OUTPUT", |
| "TX SWR_INPUT3", "ADC4_OUTPUT"; |
| |
| wcd-playback-dai-link { |
| link-name = "WCD Playback"; |
| |
| cpu { |
| sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>; |
| }; |
| |
| codec { |
| sound-dai = <&wcd939x 0>, <&swr1 0>, <&lpass_rxmacro 0>; |
| }; |
| |
| platform { |
| sound-dai = <&q6apm>; |
| }; |
| }; |
| |
| wcd-capture-dai-link { |
| link-name = "WCD Capture"; |
| |
| cpu { |
| sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>; |
| }; |
| |
| codec { |
| sound-dai = <&wcd939x 1>, <&swr2 0>, <&lpass_txmacro 0>; |
| }; |
| |
| platform { |
| sound-dai = <&q6apm>; |
| }; |
| }; |
| |
| wsa-dai-link { |
| link-name = "WSA Playback"; |
| |
| cpu { |
| sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>; |
| }; |
| |
| codec { |
| sound-dai = <&left_spkr>, <&right_spkr>, <&swr0 0>, <&lpass_wsamacro 0>; |
| }; |
| |
| platform { |
| sound-dai = <&q6apm>; |
| }; |
| }; |
| }; |
| |
| vph_pwr: vph-pwr-regulator { |
| compatible = "regulator-fixed"; |
| |
| regulator-name = "vph_pwr"; |
| regulator-min-microvolt = <3700000>; |
| regulator-max-microvolt = <3700000>; |
| |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| wcd939x: audio-codec { |
| compatible = "qcom,wcd9395-codec", "qcom,wcd9390-codec"; |
| |
| pinctrl-0 = <&wcd_default>; |
| pinctrl-names = "default"; |
| |
| qcom,micbias1-microvolt = <1800000>; |
| qcom,micbias2-microvolt = <1800000>; |
| qcom,micbias3-microvolt = <1800000>; |
| qcom,micbias4-microvolt = <1800000>; |
| qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>; |
| qcom,mbhc-headset-vthreshold-microvolt = <1700000>; |
| qcom,mbhc-headphone-vthreshold-microvolt = <50000>; |
| qcom,rx-device = <&wcd_rx>; |
| qcom,tx-device = <&wcd_tx>; |
| |
| reset-gpios = <&tlmm 107 GPIO_ACTIVE_LOW>; |
| |
| vdd-buck-supply = <&vreg_l15b_1p8>; |
| vdd-rxtx-supply = <&vreg_l15b_1p8>; |
| vdd-io-supply = <&vreg_l15b_1p8>; |
| vdd-mic-bias-supply = <&vreg_bob1>; |
| |
| #sound-dai-cells = <1>; |
| |
| mode-switch; |
| orientation-switch; |
| |
| port { |
| wcd_codec_headset_in: endpoint { |
| remote-endpoint = <&wcd_usbss_headset_out>; |
| }; |
| }; |
| }; |
| |
| wcn7850-pmu { |
| compatible = "qcom,wcn7850-pmu"; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&wlan_en>, <&bt_default>; |
| |
| wlan-enable-gpios = <&tlmm 16 GPIO_ACTIVE_HIGH>; |
| bt-enable-gpios = <&tlmm 17 GPIO_ACTIVE_HIGH>; |
| |
| vdd-supply = <&vreg_s4i_0p85>; |
| vddio-supply = <&vreg_l15b_1p8>; |
| vddio1p2-supply = <&vreg_l3c_1p2>; |
| vddaon-supply = <&vreg_s2c_0p8>; |
| vdddig-supply = <&vreg_s3c_0p9>; |
| vddrfa1p2-supply = <&vreg_s1c_1p2>; |
| vddrfa1p8-supply = <&vreg_s6c_1p8>; |
| |
| clocks = <&rpmhcc RPMH_RF_CLK1>; |
| |
| regulators { |
| vreg_pmu_rfa_cmn: ldo0 { |
| regulator-name = "vreg_pmu_rfa_cmn"; |
| }; |
| |
| vreg_pmu_aon_0p59: ldo1 { |
| regulator-name = "vreg_pmu_aon_0p59"; |
| }; |
| |
| vreg_pmu_wlcx_0p8: ldo2 { |
| regulator-name = "vreg_pmu_wlcx_0p8"; |
| }; |
| |
| vreg_pmu_wlmx_0p85: ldo3 { |
| regulator-name = "vreg_pmu_wlmx_0p85"; |
| }; |
| |
| vreg_pmu_btcmx_0p85: ldo4 { |
| regulator-name = "vreg_pmu_btcmx_0p85"; |
| }; |
| |
| vreg_pmu_rfa_0p8: ldo5 { |
| regulator-name = "vreg_pmu_rfa_0p8"; |
| }; |
| |
| vreg_pmu_rfa_1p2: ldo6 { |
| regulator-name = "vreg_pmu_rfa_1p2"; |
| }; |
| |
| vreg_pmu_rfa_1p8: ldo7 { |
| regulator-name = "vreg_pmu_rfa_1p8"; |
| }; |
| |
| vreg_pmu_pcie_0p9: ldo8 { |
| regulator-name = "vreg_pmu_pcie_0p9"; |
| }; |
| |
| vreg_pmu_pcie_1p8: ldo9 { |
| regulator-name = "vreg_pmu_pcie_1p8"; |
| }; |
| }; |
| }; |
| }; |
| |
| &apps_rsc { |
| regulators-0 { |
| compatible = "qcom,pm8550-rpmh-regulators"; |
| |
| vdd-bob1-supply = <&vph_pwr>; |
| vdd-bob2-supply = <&vph_pwr>; |
| vdd-l2-l13-l14-supply = <&vreg_bob1>; |
| vdd-l3-supply = <&vreg_s1c_1p2>; |
| vdd-l5-l16-supply = <&vreg_bob1>; |
| vdd-l6-l7-supply = <&vreg_bob1>; |
| vdd-l8-l9-supply = <&vreg_bob1>; |
| vdd-l11-supply = <&vreg_s1c_1p2>; |
| vdd-l12-supply = <&vreg_s6c_1p8>; |
| vdd-l15-supply = <&vreg_s6c_1p8>; |
| vdd-l17-supply = <&vreg_bob2>; |
| |
| qcom,pmic-id = "b"; |
| |
| vreg_bob1: bob1 { |
| regulator-name = "vreg_bob1"; |
| regulator-min-microvolt = <3296000>; |
| regulator-max-microvolt = <3960000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_bob2: bob2 { |
| regulator-name = "vreg_bob2"; |
| regulator-min-microvolt = <2720000>; |
| regulator-max-microvolt = <3008000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l2b_3p0: ldo2 { |
| regulator-name = "vreg_l2b_3p0"; |
| regulator-min-microvolt = <3008000>; |
| regulator-max-microvolt = <3008000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-allow-set-load; |
| regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l5b_3p1: ldo5 { |
| regulator-name = "vreg_l5b_3p1"; |
| regulator-min-microvolt = <3104000>; |
| regulator-max-microvolt = <3104000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-allow-set-load; |
| regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l6b_1p8: ldo6 { |
| regulator-name = "vreg_l6b_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3008000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-allow-set-load; |
| regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l7b_1p8: ldo7 { |
| regulator-name = "vreg_l7b_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3008000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l8b_1p8: ldo8 { |
| regulator-name = "vreg_l8b_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3008000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-allow-set-load; |
| regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l11b_1p2: ldo11 { |
| regulator-name = "vreg_l11b_1p2"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1504000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-allow-set-load; |
| regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l12b_1p8: ldo12 { |
| regulator-name = "vreg_l12b_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-allow-set-load; |
| regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l13b_3p0: ldo13 { |
| regulator-name = "vreg_l13b_3p0"; |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3000000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-allow-set-load; |
| regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l14b_3p2: ldo14 { |
| regulator-name = "vreg_l14b_3p2"; |
| regulator-min-microvolt = <3200000>; |
| regulator-max-microvolt = <3200000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-allow-set-load; |
| regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l15b_1p8: ldo15 { |
| regulator-name = "vreg_l15b_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-allow-set-load; |
| regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l16b_2p8: ldo16 { |
| regulator-name = "vreg_l16b_2p8"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-allow-set-load; |
| regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l17b_2p5: ldo17 { |
| regulator-name = "vreg_l17b_2p5"; |
| regulator-min-microvolt = <2504000>; |
| regulator-max-microvolt = <2504000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-allow-set-load; |
| regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| |
| regulators-1 { |
| compatible = "qcom,pm8550vs-rpmh-regulators"; |
| |
| vdd-l1-supply = <&vreg_s1c_1p2>; |
| vdd-l2-supply = <&vreg_s1c_1p2>; |
| vdd-l3-supply = <&vreg_s1c_1p2>; |
| vdd-s1-supply = <&vph_pwr>; |
| vdd-s2-supply = <&vph_pwr>; |
| vdd-s3-supply = <&vph_pwr>; |
| vdd-s4-supply = <&vph_pwr>; |
| vdd-s5-supply = <&vph_pwr>; |
| vdd-s6-supply = <&vph_pwr>; |
| |
| qcom,pmic-id = "c"; |
| |
| vreg_s1c_1p2: smps1 { |
| regulator-name = "vreg_s1c_1p2"; |
| regulator-min-microvolt = <1256000>; |
| regulator-max-microvolt = <1348000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_s2c_0p8: smps2 { |
| regulator-name = "vreg_s2c_0p8"; |
| regulator-min-microvolt = <852000>; |
| regulator-max-microvolt = <1036000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_s3c_0p9: smps3 { |
| regulator-name = "vreg_s3c_0p9"; |
| regulator-min-microvolt = <976000>; |
| regulator-max-microvolt = <1064000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_s4c_1p2: smps4 { |
| regulator-name = "vreg_s4c_1p2"; |
| regulator-min-microvolt = <1224000>; |
| regulator-max-microvolt = <1280000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_s5c_0p7: smps5 { |
| regulator-name = "vreg_s5c_0p7"; |
| regulator-min-microvolt = <752000>; |
| regulator-max-microvolt = <900000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_s6c_1p8: smps6 { |
| regulator-name = "vreg_s6c_1p8"; |
| regulator-min-microvolt = <1856000>; |
| regulator-max-microvolt = <2000000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l1c_1p2: ldo1 { |
| regulator-name = "vreg_l1c_1p2"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-allow-set-load; |
| regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l3c_1p2: ldo3 { |
| regulator-name = "vreg_l3c_1p2"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-allow-set-load; |
| regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| |
| regulators-2 { |
| compatible = "qcom,pm8550vs-rpmh-regulators"; |
| |
| vdd-l1-supply = <&vreg_s3c_0p9>; |
| |
| qcom,pmic-id = "d"; |
| |
| vreg_l1d_0p88: ldo1 { |
| regulator-name = "vreg_l1d_0p88"; |
| regulator-min-microvolt = <912000>; |
| regulator-max-microvolt = <920000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-allow-set-load; |
| regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| |
| regulators-3 { |
| compatible = "qcom,pm8550vs-rpmh-regulators"; |
| |
| vdd-l3-supply = <&vreg_s3c_0p9>; |
| |
| qcom,pmic-id = "e"; |
| |
| vreg_l3e_0p9: ldo3 { |
| regulator-name = "vreg_l3e_0p9"; |
| regulator-min-microvolt = <880000>; |
| regulator-max-microvolt = <920000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-allow-set-load; |
| regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| |
| regulators-4 { |
| compatible = "qcom,pm8550vs-rpmh-regulators"; |
| |
| vdd-l1-supply = <&vreg_s3c_0p9>; |
| vdd-l3-supply = <&vreg_s3c_0p9>; |
| |
| qcom,pmic-id = "g"; |
| |
| vreg_l1g_0p91: ldo1 { |
| regulator-name = "vreg_l1g_0p91"; |
| regulator-min-microvolt = <912000>; |
| regulator-max-microvolt = <920000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-allow-set-load; |
| regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l3g_0p91: ldo3 { |
| regulator-name = "vreg_l3g_0p91"; |
| regulator-min-microvolt = <880000>; |
| regulator-max-microvolt = <912000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-allow-set-load; |
| regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| |
| regulators-5 { |
| compatible = "qcom,pm8550ve-rpmh-regulators"; |
| |
| vdd-l1-supply = <&vreg_s3c_0p9>; |
| vdd-l2-supply = <&vreg_s3c_0p9>; |
| vdd-l3-supply = <&vreg_s1c_1p2>; |
| vdd-s4-supply = <&vph_pwr>; |
| |
| qcom,pmic-id = "i"; |
| |
| vreg_s4i_0p85: smps4 { |
| regulator-name = "vreg_s4i_0p85"; |
| regulator-min-microvolt = <852000>; |
| regulator-max-microvolt = <1004000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l1i_0p88: ldo1 { |
| regulator-name = "vreg_l1i_0p88"; |
| regulator-min-microvolt = <880000>; |
| regulator-max-microvolt = <912000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-allow-set-load; |
| regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l2i_0p88: ldo2 { |
| regulator-name = "vreg_l2i_0p88"; |
| regulator-min-microvolt = <880000>; |
| regulator-max-microvolt = <912000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-allow-set-load; |
| regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l3i_1p2: ldo3 { |
| regulator-name = "vreg_l3i_0p91"; |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-allow-set-load; |
| regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| |
| regulators-6 { |
| compatible = "qcom,pm8010-rpmh-regulators"; |
| qcom,pmic-id = "m"; |
| |
| vdd-l1-l2-supply = <&vreg_s1c_1p2>; |
| vdd-l3-l4-supply = <&vreg_bob2>; |
| vdd-l5-supply = <&vreg_s6c_1p8>; |
| vdd-l6-supply = <&vreg_bob1>; |
| vdd-l7-supply = <&vreg_bob1>; |
| |
| vreg_l1m_1p1: ldo1 { |
| regulator-name = "vreg_l1m_1p1"; |
| regulator-min-microvolt = <1104000>; |
| regulator-max-microvolt = <1104000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-allow-set-load; |
| regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l2m_1p056: ldo2 { |
| regulator-name = "vreg_l2m_1p056"; |
| regulator-min-microvolt = <1056000>; |
| regulator-max-microvolt = <1056000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-allow-set-load; |
| regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l3m_2p8: ldo3 { |
| regulator-name = "vreg_l3m_2p8"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l4m_2p8: ldo4 { |
| regulator-name = "vreg_l4m_2p8"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l5m_1p8: ldo5 { |
| regulator-name = "vreg_l5m_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l6m_2p8: ldo6 { |
| regulator-name = "vreg_l6m_2p8"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l7m_2p96: ldo7 { |
| regulator-name = "vreg_l7m_2p96"; |
| regulator-min-microvolt = <2960000>; |
| regulator-max-microvolt = <2960000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| |
| regulators-7 { |
| compatible = "qcom,pm8010-rpmh-regulators"; |
| qcom,pmic-id = "n"; |
| |
| vdd-l1-l2-supply = <&vreg_s1c_1p2>; |
| vdd-l3-l4-supply = <&vreg_s6c_1p8>; |
| vdd-l5-supply = <&vreg_bob2>; |
| vdd-l6-supply = <&vreg_bob2>; |
| vdd-l7-supply = <&vreg_bob1>; |
| |
| vreg_l1n_1p1: ldo1 { |
| regulator-name = "vreg_l1n_1p1"; |
| regulator-min-microvolt = <1104000>; |
| regulator-max-microvolt = <1104000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-allow-set-load; |
| regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l2n_1p056: ldo2 { |
| regulator-name = "vreg_l2n_1p056"; |
| regulator-min-microvolt = <1056000>; |
| regulator-max-microvolt = <1056000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| regulator-allow-set-load; |
| regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l3n_1p8: ldo3 { |
| regulator-name = "vreg_l3n_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l4n_1p8: ldo4 { |
| regulator-name = "vreg_l4n_1p8"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l5n_2p8: ldo5 { |
| regulator-name = "vreg_l5n_2p8"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l6n_2p8: ldo6 { |
| regulator-name = "vreg_l6n_2p8"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| |
| vreg_l7n_3p3: ldo7 { |
| regulator-name = "vreg_l7n_3p3"; |
| regulator-min-microvolt = <3304000>; |
| regulator-max-microvolt = <3304000>; |
| regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| }; |
| }; |
| }; |
| |
| &dispcc { |
| status = "okay"; |
| }; |
| |
| &gpi_dma1 { |
| status = "okay"; |
| }; |
| |
| &i2c3 { |
| status = "okay"; |
| |
| wcd_usbss: typec-mux@e { |
| compatible = "qcom,wcd9395-usbss", "qcom,wcd9390-usbss"; |
| reg = <0xe>; |
| |
| vdd-supply = <&vreg_l15b_1p8>; |
| reset-gpios = <&tlmm 152 GPIO_ACTIVE_HIGH>; |
| |
| mode-switch; |
| orientation-switch; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| wcd_usbss_sbu_mux: endpoint { |
| remote-endpoint = <&pmic_glink_sbu>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| wcd_usbss_headset_out: endpoint { |
| remote-endpoint = <&wcd_codec_headset_in>; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| &i2c6 { |
| status = "okay"; |
| |
| typec-mux@1c { |
| compatible = "onnn,nb7vpq904m"; |
| reg = <0x1c>; |
| |
| vcc-supply = <&vreg_l15b_1p8>; |
| |
| retimer-switch; |
| orientation-switch; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| |
| redriver_ss_out: endpoint { |
| remote-endpoint = <&pmic_glink_ss_in>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| |
| redriver_ss_in: endpoint { |
| data-lanes = <3 2 1 0>; |
| remote-endpoint = <&usb_dp_qmpphy_out>; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| &ipa { |
| qcom,gsi-loader = "self"; |
| memory-region = <&ipa_fw_mem>; |
| firmware-name = "qcom/sm8650/ipa_fws.mbn"; |
| status = "okay"; |
| }; |
| |
| &gpu { |
| status = "okay"; |
| |
| zap-shader { |
| firmware-name = "qcom/sm8650/gen70900_zap.mbn"; |
| }; |
| }; |
| |
| &lpass_tlmm { |
| spkr_1_sd_n_active: spkr-1-sd-n-active-state { |
| pins = "gpio21"; |
| function = "gpio"; |
| drive-strength = <16>; |
| bias-disable; |
| output-low; |
| }; |
| }; |
| |
| &mdss { |
| status = "okay"; |
| }; |
| |
| &mdss_dsi0 { |
| vdda-supply = <&vreg_l3i_1p2>; |
| |
| status = "okay"; |
| |
| panel@0 { |
| compatible = "visionox,vtdr6130"; |
| reg = <0>; |
| |
| reset-gpios = <&tlmm 133 GPIO_ACTIVE_LOW>; |
| |
| vddio-supply = <&vreg_l12b_1p8>; |
| vci-supply = <&vreg_l13b_3p0>; |
| vdd-supply = <&vreg_l11b_1p2>; |
| |
| pinctrl-0 = <&disp0_reset_n_active>, <&mdp_vsync_active>; |
| pinctrl-1 = <&disp0_reset_n_suspend>, <&mdp_vsync_suspend>; |
| pinctrl-names = "default", "sleep"; |
| |
| port { |
| panel0_in: endpoint { |
| remote-endpoint = <&mdss_dsi0_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| &mdss_dsi0_out { |
| remote-endpoint = <&panel0_in>; |
| data-lanes = <0 1 2 3>; |
| }; |
| |
| &mdss_dsi0_phy { |
| vdds-supply = <&vreg_l1i_0p88>; |
| |
| status = "okay"; |
| }; |
| |
| &mdss_dp0 { |
| status = "okay"; |
| }; |
| |
| &mdss_dp0_out { |
| data-lanes = <0 1>; |
| }; |
| |
| &pcie0 { |
| wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>; |
| perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>; |
| |
| pinctrl-0 = <&pcie0_default_state>; |
| pinctrl-names = "default"; |
| |
| status = "okay"; |
| }; |
| |
| &pcieport0 { |
| wifi@0 { |
| compatible = "pci17cb,1107"; |
| reg = <0x10000 0x0 0x0 0x0 0x0>; |
| |
| vddrfacmn-supply = <&vreg_pmu_rfa_cmn>; |
| vddaon-supply = <&vreg_pmu_aon_0p59>; |
| vddwlcx-supply = <&vreg_pmu_wlcx_0p8>; |
| vddwlmx-supply = <&vreg_pmu_wlmx_0p85>; |
| vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>; |
| vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>; |
| vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>; |
| vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>; |
| vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>; |
| }; |
| }; |
| |
| &pcie0_phy { |
| vdda-phy-supply = <&vreg_l1i_0p88>; |
| vdda-pll-supply = <&vreg_l3i_1p2>; |
| |
| status = "okay"; |
| }; |
| |
| &pon_pwrkey { |
| status = "okay"; |
| }; |
| |
| &pon_resin { |
| linux,code = <KEY_VOLUMEDOWN>; |
| |
| status = "okay"; |
| }; |
| |
| &pm8550_flash { |
| status = "okay"; |
| |
| led-0 { |
| function = LED_FUNCTION_FLASH; |
| color = <LED_COLOR_ID_YELLOW>; |
| led-sources = <1>, <4>; |
| led-max-microamp = <500000>; |
| flash-max-microamp = <2000000>; |
| flash-max-timeout-us = <1280000>; |
| function-enumerator = <0>; |
| }; |
| |
| led-1 { |
| function = LED_FUNCTION_FLASH; |
| color = <LED_COLOR_ID_WHITE>; |
| led-sources = <2>, <3>; |
| led-max-microamp = <500000>; |
| flash-max-microamp = <2000000>; |
| flash-max-timeout-us = <1280000>; |
| function-enumerator = <1>; |
| }; |
| }; |
| |
| &pm8550_gpios { |
| volume_up_n: volume-up-n-state { |
| pins = "gpio6"; |
| function = "normal"; |
| bias-pull-up; |
| input-enable; |
| power-source = <1>; |
| }; |
| }; |
| |
| &pm8550_pwm { |
| status = "okay"; |
| |
| multi-led { |
| color = <LED_COLOR_ID_RGB>; |
| function = LED_FUNCTION_STATUS; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| led@1 { |
| reg = <1>; |
| color = <LED_COLOR_ID_RED>; |
| }; |
| |
| led@2 { |
| reg = <2>; |
| color = <LED_COLOR_ID_GREEN>; |
| }; |
| |
| led@3 { |
| reg = <3>; |
| color = <LED_COLOR_ID_BLUE>; |
| }; |
| }; |
| }; |
| |
| &pm8550b_eusb2_repeater { |
| vdd18-supply = <&vreg_l15b_1p8>; |
| vdd3-supply = <&vreg_l5b_3p1>; |
| }; |
| |
| &pmk8550_rtc { |
| status = "okay"; |
| }; |
| |
| &qup_i2c3_data_clk { |
| /* Use internal I2C pull-up */ |
| bias-pull-up = <2200>; |
| }; |
| |
| &qupv3_id_0 { |
| status = "okay"; |
| }; |
| |
| &qupv3_id_1 { |
| status = "okay"; |
| }; |
| |
| &remoteproc_adsp { |
| firmware-name = "qcom/sm8650/adsp.mbn", |
| "qcom/sm8650/adsp_dtb.mbn"; |
| |
| status = "okay"; |
| }; |
| |
| &remoteproc_cdsp { |
| firmware-name = "qcom/sm8650/cdsp.mbn", |
| "qcom/sm8650/cdsp_dtb.mbn"; |
| |
| status = "okay"; |
| }; |
| |
| &remoteproc_mpss { |
| firmware-name = "qcom/sm8650/modem.mbn", |
| "qcom/sm8650/modem_dtb.mbn"; |
| |
| status = "okay"; |
| }; |
| |
| &sleep_clk { |
| clock-frequency = <32000>; |
| }; |
| |
| &spi4 { |
| status = "okay"; |
| |
| touchscreen@0 { |
| compatible = "goodix,gt9916"; |
| reg = <0>; |
| |
| interrupt-parent = <&tlmm>; |
| interrupts = <162 IRQ_TYPE_LEVEL_LOW>; |
| |
| reset-gpios = <&tlmm 161 GPIO_ACTIVE_LOW>; |
| |
| avdd-supply = <&vreg_l14b_3p2>; |
| |
| spi-max-frequency = <1000000>; |
| |
| touchscreen-size-x = <1080>; |
| touchscreen-size-y = <2400>; |
| |
| pinctrl-0 = <&ts_irq>, <&ts_reset>; |
| pinctrl-names = "default"; |
| }; |
| }; |
| |
| &swr0 { |
| status = "okay"; |
| |
| /* WSA8845, Speaker Left */ |
| left_spkr: speaker@0,0 { |
| compatible = "sdw20217020400"; |
| reg = <0 0>; |
| pinctrl-0 = <&spkr_1_sd_n_active>; |
| pinctrl-names = "default"; |
| powerdown-gpios = <&lpass_tlmm 21 GPIO_ACTIVE_LOW>; |
| #sound-dai-cells = <0>; |
| sound-name-prefix = "SpkrLeft"; |
| vdd-1p8-supply = <&vreg_l15b_1p8>; |
| vdd-io-supply = <&vreg_l3c_1p2>; |
| |
| /* |
| * WSA8845 Port 1 (DAC) <=> SWR0 Port 1 (SPKR_L) |
| * WSA8845 Port 2 (COMP) <=> SWR0 Port 2 (SPKR_L_COMP) |
| * WSA8845 Port 3 (BOOST) <=> SWR0 Port 3 (SPKR_L_BOOST) |
| * WSA8845 Port 4 (PBR) <=> SWR0 Port 7 (PBR) |
| * WSA8845 Port 5 (VISENSE) <=> SWR0 Port 10 (SPKR_L_VI) |
| * WSA8845 Port 6 (CPS) <=> SWR0 Port 13 (CPS) |
| */ |
| qcom,port-mapping = <1 2 3 7 10 13>; |
| }; |
| |
| /* WSA8845, Speaker Right */ |
| right_spkr: speaker@0,1 { |
| compatible = "sdw20217020400"; |
| reg = <0 1>; |
| pinctrl-0 = <&spkr_2_sd_n_active>; |
| pinctrl-names = "default"; |
| powerdown-gpios = <&tlmm 77 GPIO_ACTIVE_LOW>; |
| #sound-dai-cells = <0>; |
| sound-name-prefix = "SpkrRight"; |
| vdd-1p8-supply = <&vreg_l15b_1p8>; |
| vdd-io-supply = <&vreg_l3c_1p2>; |
| |
| /* |
| * WSA8845 Port 1 (DAC) <=> SWR0 Port 4 (SPKR_R) |
| * WSA8845 Port 2 (COMP) <=> SWR0 Port 5 (SPKR_R_COMP) |
| * WSA8845 Port 3 (BOOST) <=> SWR0 Port 6 (SPKR_R_BOOST) |
| * WSA8845 Port 4 (PBR) <=> SWR0 Port 7 (PBR) |
| * WSA8845 Port 5 (VISENSE) <=> SWR0 Port 11 (SPKR_R_VI) |
| * WSA8845 Port 6 (CPS) <=> SWR0 Port 13 (CPS) |
| */ |
| qcom,port-mapping = <4 5 6 7 11 13>; |
| }; |
| }; |
| |
| &swr1 { |
| status = "okay"; |
| |
| /* WCD9395 RX */ |
| wcd_rx: codec@0,4 { |
| compatible = "sdw20217010e00"; |
| reg = <0 4>; |
| |
| /* |
| * WCD9395 RX Port 1 (HPH_L/R) <=> SWR1 Port 1 (HPH_L/R) |
| * WCD9395 RX Port 2 (CLSH) <=> SWR1 Port 2 (CLSH) |
| * WCD9395 RX Port 3 (COMP_L/R) <=> SWR1 Port 3 (COMP_L/R) |
| * WCD9395 RX Port 4 (LO) <=> SWR1 Port 4 (LO) |
| * WCD9395 RX Port 5 (DSD_L/R) <=> SWR1 Port 5 (DSD_L/R) |
| * WCD9395 RX Port 6 (HIFI_PCM_L/R) <=> SWR1 Port 9 (HIFI_PCM_L/R) |
| */ |
| qcom,rx-port-mapping = <1 2 3 4 5 9>; |
| }; |
| }; |
| |
| &swr2 { |
| status = "okay"; |
| |
| /* WCD9395 TX */ |
| wcd_tx: codec@0,3 { |
| compatible = "sdw20217010e00"; |
| reg = <0 3>; |
| |
| /* |
| * WCD9395 TX Port 1 (ADC1,2,3,4) <=> SWR2 Port 2 (TX SWR_INPUT 0,1,2,3) |
| * WCD9395 TX Port 2 (ADC3,4 & DMIC0,1) <=> SWR2 Port 2 (TX SWR_INPUT 0,1,2,3) |
| * WCD9395 TX Port 3 (DMIC0,1,2,3 & MBHC) <=> SWR2 Port 3 (TX SWR_INPUT 4,5,6,7) |
| * WCD9395 TX Port 4 (DMIC4,5,6,7) <=> SWR2 Port 4 (TX SWR_INPUT 8,9,10,11) |
| */ |
| qcom,tx-port-mapping = <2 2 3 4>; |
| }; |
| }; |
| |
| &tlmm { |
| /* Reserved I/Os for NFC */ |
| gpio-reserved-ranges = <32 8>, <74 1>; |
| |
| bt_default: bt-default-state { |
| bt-en-pins { |
| pins = "gpio17"; |
| function = "gpio"; |
| drive-strength = <16>; |
| bias-disable; |
| }; |
| |
| sw-ctrl-pins { |
| pins = "gpio18"; |
| function = "gpio"; |
| bias-pull-down; |
| }; |
| }; |
| |
| disp0_reset_n_active: disp0-reset-n-active-state { |
| pins = "gpio133"; |
| function = "gpio"; |
| drive-strength = <8>; |
| bias-disable; |
| }; |
| |
| disp0_reset_n_suspend: disp0-reset-n-suspend-state { |
| pins = "gpio133"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-down; |
| }; |
| |
| mdp_vsync_active: mdp-vsync-active-state { |
| pins = "gpio86"; |
| function = "mdp_vsync"; |
| drive-strength = <2>; |
| bias-pull-down; |
| }; |
| |
| mdp_vsync_suspend: mdp-vsync-suspend-state { |
| pins = "gpio86"; |
| function = "mdp_vsync"; |
| drive-strength = <2>; |
| bias-pull-down; |
| }; |
| |
| spkr_2_sd_n_active: spkr-2-sd-n-active-state { |
| pins = "gpio77"; |
| function = "gpio"; |
| drive-strength = <16>; |
| bias-disable; |
| output-low; |
| }; |
| |
| ts_irq: ts-irq-state { |
| pins = "gpio161"; |
| function = "gpio"; |
| drive-strength = <8>; |
| bias-pull-up; |
| output-disable; |
| }; |
| |
| ts_reset: ts-reset-state { |
| pins = "gpio162"; |
| function = "gpio"; |
| drive-strength = <8>; |
| bias-pull-up; |
| }; |
| |
| wcd_default: wcd-reset-n-active-state { |
| pins = "gpio107"; |
| function = "gpio"; |
| drive-strength = <16>; |
| bias-disable; |
| output-low; |
| }; |
| |
| wlan_en: wlan-en-state { |
| pins = "gpio16"; |
| function = "gpio"; |
| drive-strength = <8>; |
| bias-pull-down; |
| }; |
| }; |
| |
| &uart14 { |
| status = "okay"; |
| |
| bluetooth { |
| compatible = "qcom,wcn7850-bt"; |
| |
| vddrfacmn-supply = <&vreg_pmu_rfa_cmn>; |
| vddaon-supply = <&vreg_pmu_aon_0p59>; |
| vddwlcx-supply = <&vreg_pmu_wlcx_0p8>; |
| vddwlmx-supply = <&vreg_pmu_wlmx_0p85>; |
| vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>; |
| vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>; |
| vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>; |
| |
| max-speed = <3200000>; |
| }; |
| }; |
| |
| &uart15 { |
| status = "okay"; |
| }; |
| |
| &ufs_mem_hc { |
| reset-gpios = <&tlmm 210 GPIO_ACTIVE_LOW>; |
| |
| vcc-supply = <&vreg_l17b_2p5>; |
| vcc-max-microamp = <1300000>; |
| vccq-supply = <&vreg_l1c_1p2>; |
| vccq-max-microamp = <1200000>; |
| |
| status = "okay"; |
| }; |
| |
| &ufs_mem_phy { |
| vdda-phy-supply = <&vreg_l1d_0p88>; |
| vdda-pll-supply = <&vreg_l3i_1p2>; |
| |
| status = "okay"; |
| }; |
| |
| /* |
| * DPAUX -> WCD9395 -> USB_SBU -> USB-C |
| * eUSB2 DP/DM -> PM85550HS -> eUSB2 DP/DM -> WCD9395 -> USB-C |
| * USB SS -> NB7VPQ904MMUTWG -> USB-C |
| */ |
| |
| &usb_1 { |
| status = "okay"; |
| }; |
| |
| &usb_1_dwc3 { |
| dr_mode = "otg"; |
| usb-role-switch; |
| }; |
| |
| &usb_1_dwc3_hs { |
| remote-endpoint = <&pmic_glink_hs_in>; |
| }; |
| |
| &usb_1_hsphy { |
| vdd-supply = <&vreg_l1i_0p88>; |
| vdda12-supply = <&vreg_l3i_1p2>; |
| |
| phys = <&pm8550b_eusb2_repeater>; |
| |
| status = "okay"; |
| }; |
| |
| &usb_dp_qmpphy { |
| vdda-phy-supply = <&vreg_l3i_1p2>; |
| vdda-pll-supply = <&vreg_l3g_0p91>; |
| |
| status = "okay"; |
| }; |
| |
| &usb_dp_qmpphy_out { |
| remote-endpoint = <&redriver_ss_in>; |
| }; |
| |
| &xo_board { |
| clock-frequency = <76800000>; |
| }; |
