| // SPDX-License-Identifier: BSD-3-Clause |
| /* |
| * Copyright (c) 2024, Linaro Limited |
| */ |
| |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/input/linux-event-codes.h> |
| #include <dt-bindings/interrupt-controller/irq.h> |
| #include <dt-bindings/spmi/spmi.h> |
| |
| / { |
| thermal-zones { |
| pm8550-thermal { |
| polling-delay-passive = <100>; |
| |
| thermal-sensors = <&pm8550_temp_alarm>; |
| |
| trips { |
| trip0 { |
| temperature = <95000>; |
| hysteresis = <0>; |
| type = "passive"; |
| }; |
| |
| trip1 { |
| temperature = <115000>; |
| hysteresis = <0>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| pm8550ve-2-thermal { |
| polling-delay-passive = <100>; |
| |
| thermal-sensors = <&pm8550ve_2_temp_alarm>; |
| |
| trips { |
| trip0 { |
| temperature = <95000>; |
| hysteresis = <0>; |
| type = "passive"; |
| }; |
| |
| trip1 { |
| temperature = <115000>; |
| hysteresis = <0>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| pmc8380-3-thermal { |
| polling-delay-passive = <100>; |
| |
| thermal-sensors = <&pmc8380_3_temp_alarm>; |
| |
| trips { |
| trip0 { |
| temperature = <95000>; |
| hysteresis = <0>; |
| type = "passive"; |
| }; |
| |
| trip1 { |
| temperature = <115000>; |
| hysteresis = <0>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| pmc8380-4-thermal { |
| polling-delay-passive = <100>; |
| |
| thermal-sensors = <&pmc8380_4_temp_alarm>; |
| |
| trips { |
| trip0 { |
| temperature = <95000>; |
| hysteresis = <0>; |
| type = "passive"; |
| }; |
| |
| trip1 { |
| temperature = <115000>; |
| hysteresis = <0>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| pmc8380-5-thermal { |
| polling-delay-passive = <100>; |
| |
| thermal-sensors = <&pmc8380_5_temp_alarm>; |
| |
| trips { |
| trip0 { |
| temperature = <95000>; |
| hysteresis = <0>; |
| type = "passive"; |
| }; |
| |
| trip1 { |
| temperature = <115000>; |
| hysteresis = <0>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| pmc8380-6-thermal { |
| polling-delay-passive = <100>; |
| |
| thermal-sensors = <&pmc8380_6_temp_alarm>; |
| |
| trips { |
| trip0 { |
| temperature = <95000>; |
| hysteresis = <0>; |
| type = "passive"; |
| }; |
| |
| trip1 { |
| temperature = <115000>; |
| hysteresis = <0>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| pm8550ve-8-thermal { |
| polling-delay-passive = <100>; |
| |
| thermal-sensors = <&pm8550ve_8_temp_alarm>; |
| |
| trips { |
| trip0 { |
| temperature = <95000>; |
| hysteresis = <0>; |
| type = "passive"; |
| }; |
| |
| trip1 { |
| temperature = <115000>; |
| hysteresis = <0>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| pm8550ve-9-thermal { |
| polling-delay-passive = <100>; |
| |
| thermal-sensors = <&pm8550ve_9_temp_alarm>; |
| |
| trips { |
| trip0 { |
| temperature = <95000>; |
| hysteresis = <0>; |
| type = "passive"; |
| }; |
| |
| trip1 { |
| temperature = <115000>; |
| hysteresis = <0>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| pm8010-thermal { |
| polling-delay-passive = <100>; |
| |
| thermal-sensors = <&pm8010_temp_alarm>; |
| |
| trips { |
| trip0 { |
| temperature = <95000>; |
| hysteresis = <0>; |
| type = "passive"; |
| }; |
| |
| trip1 { |
| temperature = <115000>; |
| hysteresis = <0>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| &spmi_bus0 { |
| /* PMK8380 */ |
| pmk8550: pmic@0 { |
| compatible = "qcom,pm8550", "qcom,spmi-pmic"; |
| reg = <0x0 SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pmk8550_pon: pon@1300 { |
| compatible = "qcom,pmk8350-pon"; |
| reg = <0x1300>, <0x800>; |
| reg-names = "hlos", "pbs"; |
| |
| pon_pwrkey: pwrkey { |
| compatible = "qcom,pmk8350-pwrkey"; |
| interrupts = <0x0 0x13 0x7 IRQ_TYPE_EDGE_BOTH>; |
| linux,code = <KEY_POWER>; |
| }; |
| |
| pon_resin: resin { |
| compatible = "qcom,pmk8350-resin"; |
| interrupts = <0x0 0x13 0x6 IRQ_TYPE_EDGE_BOTH>; |
| status = "disabled"; |
| }; |
| }; |
| |
| pmk8550_rtc: rtc@6100 { |
| compatible = "qcom,pmk8350-rtc"; |
| reg = <0x6100>, <0x6200>; |
| reg-names = "rtc", "alarm"; |
| interrupts = <0x0 0x62 0x1 IRQ_TYPE_EDGE_RISING>; |
| /* Not yet sure what blocks access */ |
| status = "reserved"; |
| }; |
| |
| pmk8550_sdam_2: nvram@7100 { |
| compatible = "qcom,spmi-sdam"; |
| reg = <0x7100>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0x7100 0x100>; |
| |
| reboot_reason: reboot-reason@48 { |
| reg = <0x48 0x1>; |
| bits = <1 7>; |
| }; |
| }; |
| |
| pmk8550_gpios: gpio@8800 { |
| compatible = "qcom,pmk8550-gpio", "qcom,spmi-gpio"; |
| reg = <0xb800>; |
| gpio-controller; |
| gpio-ranges = <&pmk8550_gpios 0 0 6>; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| pmk8550_pwm: pwm { |
| compatible = "qcom,pmk8550-pwm"; |
| |
| #pwm-cells = <2>; |
| |
| status = "disabled"; |
| }; |
| }; |
| |
| /* PMC8380C */ |
| pm8550: pmic@1 { |
| compatible = "qcom,pm8550", "qcom,spmi-pmic"; |
| reg = <0x1 SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pm8550_temp_alarm: temp-alarm@a00 { |
| compatible = "qcom,spmi-temp-alarm"; |
| reg = <0xa00>; |
| interrupts = <0x1 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; |
| #thermal-sensor-cells = <0>; |
| }; |
| |
| pm8550_gpios: gpio@8800 { |
| compatible = "qcom,pm8550-gpio", "qcom,spmi-gpio"; |
| reg = <0x8800>; |
| gpio-controller; |
| gpio-ranges = <&pm8550_gpios 0 0 12>; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| pm8550_flash: led-controller@ee00 { |
| compatible = "qcom,pm8550-flash-led", "qcom,spmi-flash-led"; |
| reg = <0xee00>; |
| status = "disabled"; |
| }; |
| |
| pm8550_pwm: pwm { |
| compatible = "qcom,pm8550-pwm", "qcom,pm8350c-pwm"; |
| #pwm-cells = <2>; |
| |
| status = "disabled"; |
| }; |
| }; |
| |
| /* PMC8380VE */ |
| pm8550ve_2: pmic@2 { |
| compatible = "qcom,pm8550", "qcom,spmi-pmic"; |
| reg = <0x2 SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pm8550ve_2_temp_alarm: temp-alarm@a00 { |
| compatible = "qcom,spmi-temp-alarm"; |
| reg = <0xa00>; |
| interrupts = <0x2 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; |
| #thermal-sensor-cells = <0>; |
| }; |
| |
| pm8550ve_2_gpios: gpio@8800 { |
| compatible = "qcom,pm8550ve-gpio", "qcom,spmi-gpio"; |
| reg = <0x8800>; |
| gpio-controller; |
| gpio-ranges = <&pm8550ve_2_gpios 0 0 8>; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| /* PMC8380 is actually not a PM8550 series rebrand */ |
| pmc8380_3: pmic@3 { |
| compatible = "qcom,pmc8380", "qcom,spmi-pmic"; |
| reg = <0x3 SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pmc8380_3_temp_alarm: temp-alarm@a00 { |
| compatible = "qcom,spmi-temp-alarm"; |
| reg = <0xa00>; |
| interrupts = <0x3 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; |
| #thermal-sensor-cells = <0>; |
| }; |
| |
| pmc8380_3_gpios: gpio@8800 { |
| compatible = "qcom,pmc8380-gpio", "qcom,spmi-gpio"; |
| reg = <0x8800>; |
| gpio-controller; |
| gpio-ranges = <&pmc8380_3_gpios 0 0 10>; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| pmc8380_4: pmic@4 { |
| compatible = "qcom,pmc8380", "qcom,spmi-pmic"; |
| reg = <0x4 SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pmc8380_4_temp_alarm: temp-alarm@a00 { |
| compatible = "qcom,spmi-temp-alarm"; |
| reg = <0xa00>; |
| interrupts = <0x4 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; |
| #thermal-sensor-cells = <0>; |
| }; |
| |
| pmc8380_4_gpios: gpio@8800 { |
| compatible = "qcom,pmc8380-gpio", "qcom,spmi-gpio"; |
| reg = <0x8800>; |
| gpio-controller; |
| gpio-ranges = <&pmc8380_4_gpios 0 0 10>; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| pmc8380_5: pmic@5 { |
| compatible = "qcom,pmc8380", "qcom,spmi-pmic"; |
| reg = <0x5 SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pmc8380_5_temp_alarm: temp-alarm@a00 { |
| compatible = "qcom,spmi-temp-alarm"; |
| reg = <0xa00>; |
| interrupts = <0x5 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; |
| #thermal-sensor-cells = <0>; |
| }; |
| |
| pmc8380_5_gpios: gpio@8800 { |
| compatible = "qcom,pmc8380-gpio", "qcom,spmi-gpio"; |
| reg = <0x8800>; |
| gpio-controller; |
| gpio-ranges = <&pmc8380_5_gpios 0 0 10>; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| pmc8380_6: pmic@6 { |
| compatible = "qcom,pmc8380", "qcom,spmi-pmic"; |
| reg = <0x6 SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pmc8380_6_temp_alarm: temp-alarm@a00 { |
| compatible = "qcom,spmi-temp-alarm"; |
| reg = <0xa00>; |
| interrupts = <0x6 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; |
| #thermal-sensor-cells = <0>; |
| }; |
| |
| pmc8380_6_gpios: gpio@8800 { |
| compatible = "qcom,pmc8380-gpio", "qcom,spmi-gpio"; |
| reg = <0x8800>; |
| gpio-controller; |
| gpio-ranges = <&pmc8380_6_gpios 0 0 10>; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| /* PMC8380VE */ |
| pm8550ve_8: pmic@8 { |
| compatible = "qcom,pm8550", "qcom,spmi-pmic"; |
| reg = <0x8 SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pm8550ve_8_temp_alarm: temp-alarm@a00 { |
| compatible = "qcom,spmi-temp-alarm"; |
| reg = <0xa00>; |
| interrupts = <0x8 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; |
| #thermal-sensor-cells = <0>; |
| }; |
| |
| pm8550ve_8_gpios: gpio@8800 { |
| compatible = "qcom,pm8550ve-gpio", "qcom,spmi-gpio"; |
| reg = <0x8800>; |
| gpio-controller; |
| gpio-ranges = <&pm8550ve_8_gpios 0 0 8>; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| /* PMC8380VE */ |
| pm8550ve_9: pmic@9 { |
| compatible = "qcom,pm8550", "qcom,spmi-pmic"; |
| reg = <0x9 SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pm8550ve_9_temp_alarm: temp-alarm@a00 { |
| compatible = "qcom,spmi-temp-alarm"; |
| reg = <0xa00>; |
| interrupts = <0x9 0xa 0x0 IRQ_TYPE_EDGE_BOTH>; |
| #thermal-sensor-cells = <0>; |
| }; |
| |
| pm8550ve_9_gpios: gpio@8800 { |
| compatible = "qcom,pm8550ve-gpio", "qcom,spmi-gpio"; |
| reg = <0x8800>; |
| gpio-controller; |
| gpio-ranges = <&pm8550ve_9_gpios 0 0 8>; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| pm8010: pmic@c { |
| compatible = "qcom,pm8010", "qcom,spmi-pmic"; |
| reg = <0xc SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pm8010_temp_alarm: temp-alarm@2400 { |
| compatible = "qcom,spmi-temp-alarm"; |
| reg = <0x2400>; |
| interrupts = <0xc 0x24 0x0 IRQ_TYPE_EDGE_BOTH>; |
| #thermal-sensor-cells = <0>; |
| }; |
| }; |
| }; |
| |
| &spmi_bus1 { |
| smb2360_0: pmic@7 { |
| compatible = "qcom,smb2360", "qcom,spmi-pmic"; |
| reg = <0x7 SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| smb2360_0_eusb2_repeater: phy@fd00 { |
| compatible = "qcom,smb2360-eusb2-repeater"; |
| reg = <0xfd00>; |
| #phy-cells = <0>; |
| }; |
| }; |
| |
| smb2360_1: pmic@a { |
| compatible = "qcom,smb2360", "qcom,spmi-pmic"; |
| reg = <0xa SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| smb2360_1_eusb2_repeater: phy@fd00 { |
| compatible = "qcom,smb2360-eusb2-repeater"; |
| reg = <0xfd00>; |
| #phy-cells = <0>; |
| }; |
| }; |
| |
| smb2360_2: pmic@b { |
| compatible = "qcom,smb2360", "qcom,spmi-pmic"; |
| reg = <0xb SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| |
| smb2360_2_eusb2_repeater: phy@fd00 { |
| compatible = "qcom,smb2360-eusb2-repeater"; |
| reg = <0xfd00>; |
| #phy-cells = <0>; |
| }; |
| }; |
| |
| smb2360_3: pmic@c { |
| compatible = "qcom,smb2360", "qcom,spmi-pmic"; |
| reg = <0xc SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| |
| smb2360_3_eusb2_repeater: phy@fd00 { |
| compatible = "qcom,smb2360-eusb2-repeater"; |
| reg = <0xfd00>; |
| #phy-cells = <0>; |
| }; |
| }; |
| }; |
