| // SPDX-License-Identifier: GPL-2.0-or-later |
| /* |
| * Driver for the Atmel AHB DMA Controller (aka HDMA or DMAC on AT91 systems) |
| * |
| * Copyright (C) 2008 Atmel Corporation |
| * Copyright (C) 2022 Microchip Technology, Inc. and its subsidiaries |
| * |
| * This supports the Atmel AHB DMA Controller found in several Atmel SoCs. |
| * The only Atmel DMA Controller that is not covered by this driver is the one |
| * found on AT91SAM9263. |
| */ |
| |
| #include <dt-bindings/dma/at91.h> |
| #include <linux/bitfield.h> |
| #include <linux/clk.h> |
| #include <linux/dmaengine.h> |
| #include <linux/dmapool.h> |
| #include <linux/dma-mapping.h> |
| #include <linux/interrupt.h> |
| #include <linux/module.h> |
| #include <linux/of.h> |
| #include <linux/overflow.h> |
| #include <linux/of_platform.h> |
| #include <linux/of_dma.h> |
| #include <linux/platform_device.h> |
| #include <linux/slab.h> |
| |
| #include "dmaengine.h" |
| #include "virt-dma.h" |
| |
| /* |
| * Glossary |
| * -------- |
| * |
| * at_hdmac : Name of the ATmel AHB DMA Controller |
| * at_dma_ / atdma : ATmel DMA controller entity related |
| * atc_ / atchan : ATmel DMA Channel entity related |
| */ |
| |
| #define AT_DMA_MAX_NR_CHANNELS 8 |
| |
| /* Global Configuration Register */ |
| #define AT_DMA_GCFG 0x00 |
| #define AT_DMA_IF_BIGEND(i) BIT((i)) /* AHB-Lite Interface i in Big-endian mode */ |
| #define AT_DMA_ARB_CFG BIT(4) /* Arbiter mode. */ |
| |
| /* Controller Enable Register */ |
| #define AT_DMA_EN 0x04 |
| #define AT_DMA_ENABLE BIT(0) |
| |
| /* Software Single Request Register */ |
| #define AT_DMA_SREQ 0x08 |
| #define AT_DMA_SSREQ(x) BIT((x) << 1) /* Request a source single transfer on channel x */ |
| #define AT_DMA_DSREQ(x) BIT(1 + ((x) << 1)) /* Request a destination single transfer on channel x */ |
| |
| /* Software Chunk Transfer Request Register */ |
| #define AT_DMA_CREQ 0x0c |
| #define AT_DMA_SCREQ(x) BIT((x) << 1) /* Request a source chunk transfer on channel x */ |
| #define AT_DMA_DCREQ(x) BIT(1 + ((x) << 1)) /* Request a destination chunk transfer on channel x */ |
| |
| /* Software Last Transfer Flag Register */ |
| #define AT_DMA_LAST 0x10 |
| #define AT_DMA_SLAST(x) BIT((x) << 1) /* This src rq is last tx of buffer on channel x */ |
| #define AT_DMA_DLAST(x) BIT(1 + ((x) << 1)) /* This dst rq is last tx of buffer on channel x */ |
| |
| /* Request Synchronization Register */ |
| #define AT_DMA_SYNC 0x14 |
| #define AT_DMA_SYR(h) BIT((h)) /* Synchronize handshake line h */ |
| |
| /* Error, Chained Buffer transfer completed and Buffer transfer completed Interrupt registers */ |
| #define AT_DMA_EBCIER 0x18 /* Enable register */ |
| #define AT_DMA_EBCIDR 0x1c /* Disable register */ |
| #define AT_DMA_EBCIMR 0x20 /* Mask Register */ |
| #define AT_DMA_EBCISR 0x24 /* Status Register */ |
| #define AT_DMA_CBTC_OFFSET 8 |
| #define AT_DMA_ERR_OFFSET 16 |
| #define AT_DMA_BTC(x) BIT((x)) |
| #define AT_DMA_CBTC(x) BIT(AT_DMA_CBTC_OFFSET + (x)) |
| #define AT_DMA_ERR(x) BIT(AT_DMA_ERR_OFFSET + (x)) |
| |
| /* Channel Handler Enable Register */ |
| #define AT_DMA_CHER 0x28 |
| #define AT_DMA_ENA(x) BIT((x)) |
| #define AT_DMA_SUSP(x) BIT(8 + (x)) |
| #define AT_DMA_KEEP(x) BIT(24 + (x)) |
| |
| /* Channel Handler Disable Register */ |
| #define AT_DMA_CHDR 0x2c |
| #define AT_DMA_DIS(x) BIT(x) |
| #define AT_DMA_RES(x) BIT(8 + (x)) |
| |
| /* Channel Handler Status Register */ |
| #define AT_DMA_CHSR 0x30 |
| #define AT_DMA_EMPT(x) BIT(16 + (x)) |
| #define AT_DMA_STAL(x) BIT(24 + (x)) |
| |
| /* Channel registers base address */ |
| #define AT_DMA_CH_REGS_BASE 0x3c |
| #define ch_regs(x) (AT_DMA_CH_REGS_BASE + (x) * 0x28) /* Channel x base addr */ |
| |
| /* Hardware register offset for each channel */ |
| #define ATC_SADDR_OFFSET 0x00 /* Source Address Register */ |
| #define ATC_DADDR_OFFSET 0x04 /* Destination Address Register */ |
| #define ATC_DSCR_OFFSET 0x08 /* Descriptor Address Register */ |
| #define ATC_CTRLA_OFFSET 0x0c /* Control A Register */ |
| #define ATC_CTRLB_OFFSET 0x10 /* Control B Register */ |
| #define ATC_CFG_OFFSET 0x14 /* Configuration Register */ |
| #define ATC_SPIP_OFFSET 0x18 /* Src PIP Configuration Register */ |
| #define ATC_DPIP_OFFSET 0x1c /* Dst PIP Configuration Register */ |
| |
| |
| /* Bitfield definitions */ |
| |
| /* Bitfields in DSCR */ |
| #define ATC_DSCR_IF GENMASK(1, 0) /* Dsc feched via AHB-Lite Interface */ |
| |
| /* Bitfields in CTRLA */ |
| #define ATC_BTSIZE_MAX GENMASK(15, 0) /* Maximum Buffer Transfer Size */ |
| #define ATC_BTSIZE GENMASK(15, 0) /* Buffer Transfer Size */ |
| #define ATC_SCSIZE GENMASK(18, 16) /* Source Chunk Transfer Size */ |
| #define ATC_DCSIZE GENMASK(22, 20) /* Destination Chunk Transfer Size */ |
| #define ATC_SRC_WIDTH GENMASK(25, 24) /* Source Single Transfer Size */ |
| #define ATC_DST_WIDTH GENMASK(29, 28) /* Destination Single Transfer Size */ |
| #define ATC_DONE BIT(31) /* Tx Done (only written back in descriptor) */ |
| |
| /* Bitfields in CTRLB */ |
| #define ATC_SIF GENMASK(1, 0) /* Src tx done via AHB-Lite Interface i */ |
| #define ATC_DIF GENMASK(5, 4) /* Dst tx done via AHB-Lite Interface i */ |
| #define AT_DMA_MEM_IF 0x0 /* interface 0 as memory interface */ |
| #define AT_DMA_PER_IF 0x1 /* interface 1 as peripheral interface */ |
| #define ATC_SRC_PIP BIT(8) /* Source Picture-in-Picture enabled */ |
| #define ATC_DST_PIP BIT(12) /* Destination Picture-in-Picture enabled */ |
| #define ATC_SRC_DSCR_DIS BIT(16) /* Src Descriptor fetch disable */ |
| #define ATC_DST_DSCR_DIS BIT(20) /* Dst Descriptor fetch disable */ |
| #define ATC_FC GENMASK(23, 21) /* Choose Flow Controller */ |
| #define ATC_FC_MEM2MEM 0x0 /* Mem-to-Mem (DMA) */ |
| #define ATC_FC_MEM2PER 0x1 /* Mem-to-Periph (DMA) */ |
| #define ATC_FC_PER2MEM 0x2 /* Periph-to-Mem (DMA) */ |
| #define ATC_FC_PER2PER 0x3 /* Periph-to-Periph (DMA) */ |
| #define ATC_FC_PER2MEM_PER 0x4 /* Periph-to-Mem (Peripheral) */ |
| #define ATC_FC_MEM2PER_PER 0x5 /* Mem-to-Periph (Peripheral) */ |
| #define ATC_FC_PER2PER_SRCPER 0x6 /* Periph-to-Periph (Src Peripheral) */ |
| #define ATC_FC_PER2PER_DSTPER 0x7 /* Periph-to-Periph (Dst Peripheral) */ |
| #define ATC_SRC_ADDR_MODE GENMASK(25, 24) |
| #define ATC_SRC_ADDR_MODE_INCR 0x0 /* Incrementing Mode */ |
| #define ATC_SRC_ADDR_MODE_DECR 0x1 /* Decrementing Mode */ |
| #define ATC_SRC_ADDR_MODE_FIXED 0x2 /* Fixed Mode */ |
| #define ATC_DST_ADDR_MODE GENMASK(29, 28) |
| #define ATC_DST_ADDR_MODE_INCR 0x0 /* Incrementing Mode */ |
| #define ATC_DST_ADDR_MODE_DECR 0x1 /* Decrementing Mode */ |
| #define ATC_DST_ADDR_MODE_FIXED 0x2 /* Fixed Mode */ |
| #define ATC_IEN BIT(30) /* BTC interrupt enable (active low) */ |
| #define ATC_AUTO BIT(31) /* Auto multiple buffer tx enable */ |
| |
| /* Bitfields in CFG */ |
| #define ATC_SRC_PER GENMASK(3, 0) /* Channel src rq associated with periph handshaking ifc h */ |
| #define ATC_DST_PER GENMASK(7, 4) /* Channel dst rq associated with periph handshaking ifc h */ |
| #define ATC_SRC_REP BIT(8) /* Source Replay Mod */ |
| #define ATC_SRC_H2SEL BIT(9) /* Source Handshaking Mod */ |
| #define ATC_SRC_PER_MSB GENMASK(11, 10) /* Channel src rq (most significant bits) */ |
| #define ATC_DST_REP BIT(12) /* Destination Replay Mod */ |
| #define ATC_DST_H2SEL BIT(13) /* Destination Handshaking Mod */ |
| #define ATC_DST_PER_MSB GENMASK(15, 14) /* Channel dst rq (most significant bits) */ |
| #define ATC_SOD BIT(16) /* Stop On Done */ |
| #define ATC_LOCK_IF BIT(20) /* Interface Lock */ |
| #define ATC_LOCK_B BIT(21) /* AHB Bus Lock */ |
| #define ATC_LOCK_IF_L BIT(22) /* Master Interface Arbiter Lock */ |
| #define ATC_AHB_PROT GENMASK(26, 24) /* AHB Protection */ |
| #define ATC_FIFOCFG GENMASK(29, 28) /* FIFO Request Configuration */ |
| #define ATC_FIFOCFG_LARGESTBURST 0x0 |
| #define ATC_FIFOCFG_HALFFIFO 0x1 |
| #define ATC_FIFOCFG_ENOUGHSPACE 0x2 |
| |
| /* Bitfields in SPIP */ |
| #define ATC_SPIP_HOLE GENMASK(15, 0) |
| #define ATC_SPIP_BOUNDARY GENMASK(25, 16) |
| |
| /* Bitfields in DPIP */ |
| #define ATC_DPIP_HOLE GENMASK(15, 0) |
| #define ATC_DPIP_BOUNDARY GENMASK(25, 16) |
| |
| #define ATC_PER_MSB GENMASK(5, 4) /* Extract MSBs of a handshaking identifier */ |
| #define ATC_SRC_PER_ID(id) \ |
| ({ typeof(id) _id = (id); \ |
| FIELD_PREP(ATC_SRC_PER_MSB, FIELD_GET(ATC_PER_MSB, _id)) | \ |
| FIELD_PREP(ATC_SRC_PER, _id); }) |
| #define ATC_DST_PER_ID(id) \ |
| ({ typeof(id) _id = (id); \ |
| FIELD_PREP(ATC_DST_PER_MSB, FIELD_GET(ATC_PER_MSB, _id)) | \ |
| FIELD_PREP(ATC_DST_PER, _id); }) |
| |
| |
| |
| /*-- descriptors -----------------------------------------------------*/ |
| |
| /* LLI == Linked List Item; aka DMA buffer descriptor */ |
| struct at_lli { |
| /* values that are not changed by hardware */ |
| u32 saddr; |
| u32 daddr; |
| /* value that may get written back: */ |
| u32 ctrla; |
| /* more values that are not changed by hardware */ |
| u32 ctrlb; |
| u32 dscr; /* chain to next lli */ |
| }; |
| |
| /** |
| * struct atdma_sg - atdma scatter gather entry |
| * @len: length of the current Linked List Item. |
| * @lli: linked list item that is passed to the DMA controller |
| * @lli_phys: physical address of the LLI. |
| */ |
| struct atdma_sg { |
| unsigned int len; |
| struct at_lli *lli; |
| dma_addr_t lli_phys; |
| }; |
| |
| /** |
| * struct at_desc - software descriptor |
| * @vd: pointer to the virtual dma descriptor. |
| * @atchan: pointer to the atmel dma channel. |
| * @total_len: total transaction byte count |
| * @sglen: number of sg entries. |
| * @sg: array of sgs. |
| * @boundary: number of transfers to perform before the automatic address increment operation |
| * @dst_hole: value to add to the destination address when the boundary has been reached |
| * @src_hole: value to add to the source address when the boundary has been reached |
| * @memset_buffer: buffer used for the memset operation |
| * @memset_paddr: physical address of the buffer used for the memset operation |
| * @memset_vaddr: virtual address of the buffer used for the memset operation |
| */ |
| struct at_desc { |
| struct virt_dma_desc vd; |
| struct at_dma_chan *atchan; |
| size_t total_len; |
| unsigned int sglen; |
| /* Interleaved data */ |
| size_t boundary; |
| size_t dst_hole; |
| size_t src_hole; |
| |
| /* Memset temporary buffer */ |
| bool memset_buffer; |
| dma_addr_t memset_paddr; |
| int *memset_vaddr; |
| struct atdma_sg sg[] __counted_by(sglen); |
| }; |
| |
| /*-- Channels --------------------------------------------------------*/ |
| |
| /** |
| * enum atc_status - information bits stored in channel status flag |
| * |
| * @ATC_IS_PAUSED: If channel is pauses |
| * @ATC_IS_CYCLIC: If channel is cyclic |
| * |
| * Manipulated with atomic operations. |
| */ |
| enum atc_status { |
| ATC_IS_PAUSED = 1, |
| ATC_IS_CYCLIC = 24, |
| }; |
| |
| /** |
| * struct at_dma_chan - internal representation of an Atmel HDMAC channel |
| * @vc: virtual dma channel entry. |
| * @atdma: pointer to the driver data. |
| * @ch_regs: memory mapped register base |
| * @mask: channel index in a mask |
| * @per_if: peripheral interface |
| * @mem_if: memory interface |
| * @status: transmit status information from irq/prep* functions |
| * to tasklet (use atomic operations) |
| * @save_cfg: configuration register that is saved on suspend/resume cycle |
| * @save_dscr: for cyclic operations, preserve next descriptor address in |
| * the cyclic list on suspend/resume cycle |
| * @dma_sconfig: configuration for slave transfers, passed via |
| * .device_config |
| * @desc: pointer to the atmel dma descriptor. |
| */ |
| struct at_dma_chan { |
| struct virt_dma_chan vc; |
| struct at_dma *atdma; |
| void __iomem *ch_regs; |
| u8 mask; |
| u8 per_if; |
| u8 mem_if; |
| unsigned long status; |
| u32 save_cfg; |
| u32 save_dscr; |
| struct dma_slave_config dma_sconfig; |
| struct at_desc *desc; |
| }; |
| |
| #define channel_readl(atchan, name) \ |
| __raw_readl((atchan)->ch_regs + ATC_##name##_OFFSET) |
| |
| #define channel_writel(atchan, name, val) \ |
| __raw_writel((val), (atchan)->ch_regs + ATC_##name##_OFFSET) |
| |
| /* |
| * Fix sconfig's burst size according to at_hdmac. We need to convert them as: |
| * 1 -> 0, 4 -> 1, 8 -> 2, 16 -> 3, 32 -> 4, 64 -> 5, 128 -> 6, 256 -> 7. |
| * |
| * This can be done by finding most significant bit set. |
| */ |
| static inline void convert_burst(u32 *maxburst) |
| { |
| if (*maxburst > 1) |
| *maxburst = fls(*maxburst) - 2; |
| else |
| *maxburst = 0; |
| } |
| |
| /* |
| * Fix sconfig's bus width according to at_hdmac. |
| * 1 byte -> 0, 2 bytes -> 1, 4 bytes -> 2. |
| */ |
| static inline u8 convert_buswidth(enum dma_slave_buswidth addr_width) |
| { |
| switch (addr_width) { |
| case DMA_SLAVE_BUSWIDTH_2_BYTES: |
| return 1; |
| case DMA_SLAVE_BUSWIDTH_4_BYTES: |
| return 2; |
| default: |
| /* For 1 byte width or fallback */ |
| return 0; |
| } |
| } |
| |
| /*-- Controller ------------------------------------------------------*/ |
| |
| /** |
| * struct at_dma - internal representation of an Atmel HDMA Controller |
| * @dma_device: dmaengine dma_device object members |
| * @regs: memory mapped register base |
| * @clk: dma controller clock |
| * @save_imr: interrupt mask register that is saved on suspend/resume cycle |
| * @all_chan_mask: all channels available in a mask |
| * @lli_pool: hw lli table |
| * @memset_pool: hw memset pool |
| * @chan: channels table to store at_dma_chan structures |
| */ |
| struct at_dma { |
| struct dma_device dma_device; |
| void __iomem *regs; |
| struct clk *clk; |
| u32 save_imr; |
| |
| u8 all_chan_mask; |
| |
| struct dma_pool *lli_pool; |
| struct dma_pool *memset_pool; |
| /* AT THE END channels table */ |
| struct at_dma_chan chan[]; |
| }; |
| |
| #define dma_readl(atdma, name) \ |
| __raw_readl((atdma)->regs + AT_DMA_##name) |
| #define dma_writel(atdma, name, val) \ |
| __raw_writel((val), (atdma)->regs + AT_DMA_##name) |
| |
| static inline struct at_desc *to_atdma_desc(struct dma_async_tx_descriptor *t) |
| { |
| return container_of(t, struct at_desc, vd.tx); |
| } |
| |
| static inline struct at_dma_chan *to_at_dma_chan(struct dma_chan *chan) |
| { |
| return container_of(chan, struct at_dma_chan, vc.chan); |
| } |
| |
| static inline struct at_dma *to_at_dma(struct dma_device *ddev) |
| { |
| return container_of(ddev, struct at_dma, dma_device); |
| } |
| |
| |
| /*-- Helper functions ------------------------------------------------*/ |
| |
| static struct device *chan2dev(struct dma_chan *chan) |
| { |
| return &chan->dev->device; |
| } |
| |
| #if defined(VERBOSE_DEBUG) |
| static void vdbg_dump_regs(struct at_dma_chan *atchan) |
| { |
| struct at_dma *atdma = to_at_dma(atchan->vc.chan.device); |
| |
| dev_err(chan2dev(&atchan->vc.chan), |
| " channel %d : imr = 0x%x, chsr = 0x%x\n", |
| atchan->vc.chan.chan_id, |
| dma_readl(atdma, EBCIMR), |
| dma_readl(atdma, CHSR)); |
| |
| dev_err(chan2dev(&atchan->vc.chan), |
| " channel: s0x%x d0x%x ctrl0x%x:0x%x cfg0x%x l0x%x\n", |
| channel_readl(atchan, SADDR), |
| channel_readl(atchan, DADDR), |
| channel_readl(atchan, CTRLA), |
| channel_readl(atchan, CTRLB), |
| channel_readl(atchan, CFG), |
| channel_readl(atchan, DSCR)); |
| } |
| #else |
| static void vdbg_dump_regs(struct at_dma_chan *atchan) {} |
| #endif |
| |
| static void atc_dump_lli(struct at_dma_chan *atchan, struct at_lli *lli) |
| { |
| dev_crit(chan2dev(&atchan->vc.chan), |
| "desc: s%pad d%pad ctrl0x%x:0x%x l%pad\n", |
| &lli->saddr, &lli->daddr, |
| lli->ctrla, lli->ctrlb, &lli->dscr); |
| } |
| |
| |
| static void atc_setup_irq(struct at_dma *atdma, int chan_id, int on) |
| { |
| u32 ebci; |
| |
| /* enable interrupts on buffer transfer completion & error */ |
| ebci = AT_DMA_BTC(chan_id) |
| | AT_DMA_ERR(chan_id); |
| if (on) |
| dma_writel(atdma, EBCIER, ebci); |
| else |
| dma_writel(atdma, EBCIDR, ebci); |
| } |
| |
| static void atc_enable_chan_irq(struct at_dma *atdma, int chan_id) |
| { |
| atc_setup_irq(atdma, chan_id, 1); |
| } |
| |
| static void atc_disable_chan_irq(struct at_dma *atdma, int chan_id) |
| { |
| atc_setup_irq(atdma, chan_id, 0); |
| } |
| |
| |
| /** |
| * atc_chan_is_enabled - test if given channel is enabled |
| * @atchan: channel we want to test status |
| */ |
| static inline int atc_chan_is_enabled(struct at_dma_chan *atchan) |
| { |
| struct at_dma *atdma = to_at_dma(atchan->vc.chan.device); |
| |
| return !!(dma_readl(atdma, CHSR) & atchan->mask); |
| } |
| |
| /** |
| * atc_chan_is_paused - test channel pause/resume status |
| * @atchan: channel we want to test status |
| */ |
| static inline int atc_chan_is_paused(struct at_dma_chan *atchan) |
| { |
| return test_bit(ATC_IS_PAUSED, &atchan->status); |
| } |
| |
| /** |
| * atc_chan_is_cyclic - test if given channel has cyclic property set |
| * @atchan: channel we want to test status |
| */ |
| static inline int atc_chan_is_cyclic(struct at_dma_chan *atchan) |
| { |
| return test_bit(ATC_IS_CYCLIC, &atchan->status); |
| } |
| |
| /** |
| * set_lli_eol - set end-of-link to descriptor so it will end transfer |
| * @desc: descriptor, signle or at the end of a chain, to end chain on |
| * @i: index of the atmel scatter gather entry that is at the end of the chain. |
| */ |
| static void set_lli_eol(struct at_desc *desc, unsigned int i) |
| { |
| u32 ctrlb = desc->sg[i].lli->ctrlb; |
| |
| ctrlb &= ~ATC_IEN; |
| ctrlb |= ATC_SRC_DSCR_DIS | ATC_DST_DSCR_DIS; |
| |
| desc->sg[i].lli->ctrlb = ctrlb; |
| desc->sg[i].lli->dscr = 0; |
| } |
| |
| #define ATC_DEFAULT_CFG FIELD_PREP(ATC_FIFOCFG, ATC_FIFOCFG_HALFFIFO) |
| #define ATC_DEFAULT_CTRLB (FIELD_PREP(ATC_SIF, AT_DMA_MEM_IF) | \ |
| FIELD_PREP(ATC_DIF, AT_DMA_MEM_IF)) |
| #define ATC_DMA_BUSWIDTHS\ |
| (BIT(DMA_SLAVE_BUSWIDTH_UNDEFINED) |\ |
| BIT(DMA_SLAVE_BUSWIDTH_1_BYTE) |\ |
| BIT(DMA_SLAVE_BUSWIDTH_2_BYTES) |\ |
| BIT(DMA_SLAVE_BUSWIDTH_4_BYTES)) |
| |
| #define ATC_MAX_DSCR_TRIALS 10 |
| |
| /* |
| * Initial number of descriptors to allocate for each channel. This could |
| * be increased during dma usage. |
| */ |
| static unsigned int init_nr_desc_per_channel = 64; |
| module_param(init_nr_desc_per_channel, uint, 0644); |
| MODULE_PARM_DESC(init_nr_desc_per_channel, |
| "initial descriptors per channel (default: 64)"); |
| |
| /** |
| * struct at_dma_platform_data - Controller configuration parameters |
| * @nr_channels: Number of channels supported by hardware (max 8) |
| * @cap_mask: dma_capability flags supported by the platform |
| */ |
| struct at_dma_platform_data { |
| unsigned int nr_channels; |
| dma_cap_mask_t cap_mask; |
| }; |
| |
| /** |
| * struct at_dma_slave - Controller-specific information about a slave |
| * @dma_dev: required DMA master device |
| * @cfg: Platform-specific initializer for the CFG register |
| */ |
| struct at_dma_slave { |
| struct device *dma_dev; |
| u32 cfg; |
| }; |
| |
| static inline unsigned int atc_get_xfer_width(dma_addr_t src, dma_addr_t dst, |
| size_t len) |
| { |
| unsigned int width; |
| |
| if (!((src | dst | len) & 3)) |
| width = 2; |
| else if (!((src | dst | len) & 1)) |
| width = 1; |
| else |
| width = 0; |
| |
| return width; |
| } |
| |
| static void atdma_lli_chain(struct at_desc *desc, unsigned int i) |
| { |
| struct atdma_sg *atdma_sg = &desc->sg[i]; |
| |
| if (i) |
| desc->sg[i - 1].lli->dscr = atdma_sg->lli_phys; |
| } |
| |
| /** |
| * atc_dostart - starts the DMA engine for real |
| * @atchan: the channel we want to start |
| */ |
| static void atc_dostart(struct at_dma_chan *atchan) |
| { |
| struct virt_dma_desc *vd = vchan_next_desc(&atchan->vc); |
| struct at_desc *desc; |
| |
| if (!vd) { |
| atchan->desc = NULL; |
| return; |
| } |
| |
| vdbg_dump_regs(atchan); |
| |
| list_del(&vd->node); |
| atchan->desc = desc = to_atdma_desc(&vd->tx); |
| |
| channel_writel(atchan, SADDR, 0); |
| channel_writel(atchan, DADDR, 0); |
| channel_writel(atchan, CTRLA, 0); |
| channel_writel(atchan, CTRLB, 0); |
| channel_writel(atchan, DSCR, desc->sg[0].lli_phys); |
| channel_writel(atchan, SPIP, |
| FIELD_PREP(ATC_SPIP_HOLE, desc->src_hole) | |
| FIELD_PREP(ATC_SPIP_BOUNDARY, desc->boundary)); |
| channel_writel(atchan, DPIP, |
| FIELD_PREP(ATC_DPIP_HOLE, desc->dst_hole) | |
| FIELD_PREP(ATC_DPIP_BOUNDARY, desc->boundary)); |
| |
| /* Don't allow CPU to reorder channel enable. */ |
| wmb(); |
| dma_writel(atchan->atdma, CHER, atchan->mask); |
| |
| vdbg_dump_regs(atchan); |
| } |
| |
| static void atdma_desc_free(struct virt_dma_desc *vd) |
| { |
| struct at_dma *atdma = to_at_dma(vd->tx.chan->device); |
| struct at_desc *desc = to_atdma_desc(&vd->tx); |
| unsigned int i; |
| |
| for (i = 0; i < desc->sglen; i++) { |
| if (desc->sg[i].lli) |
| dma_pool_free(atdma->lli_pool, desc->sg[i].lli, |
| desc->sg[i].lli_phys); |
| } |
| |
| /* If the transfer was a memset, free our temporary buffer */ |
| if (desc->memset_buffer) { |
| dma_pool_free(atdma->memset_pool, desc->memset_vaddr, |
| desc->memset_paddr); |
| desc->memset_buffer = false; |
| } |
| |
| kfree(desc); |
| } |
| |
| /** |
| * atc_calc_bytes_left - calculates the number of bytes left according to the |
| * value read from CTRLA. |
| * |
| * @current_len: the number of bytes left before reading CTRLA |
| * @ctrla: the value of CTRLA |
| */ |
| static inline u32 atc_calc_bytes_left(u32 current_len, u32 ctrla) |
| { |
| u32 btsize = FIELD_GET(ATC_BTSIZE, ctrla); |
| u32 src_width = FIELD_GET(ATC_SRC_WIDTH, ctrla); |
| |
| /* |
| * According to the datasheet, when reading the Control A Register |
| * (ctrla), the Buffer Transfer Size (btsize) bitfield refers to the |
| * number of transfers completed on the Source Interface. |
| * So btsize is always a number of source width transfers. |
| */ |
| return current_len - (btsize << src_width); |
| } |
| |
| /** |
| * atc_get_llis_residue - Get residue for a hardware linked list transfer |
| * @atchan: pointer to an atmel hdmac channel. |
| * @desc: pointer to the descriptor for which the residue is calculated. |
| * @residue: residue to be set to dma_tx_state. |
| * |
| * Calculate the residue by removing the length of the Linked List Item (LLI) |
| * already transferred from the total length. To get the current LLI we can use |
| * the value of the channel's DSCR register and compare it against the DSCR |
| * value of each LLI. |
| * |
| * The CTRLA register provides us with the amount of data already read from the |
| * source for the LLI. So we can compute a more accurate residue by also |
| * removing the number of bytes corresponding to this amount of data. |
| * |
| * However, the DSCR and CTRLA registers cannot be read both atomically. Hence a |
| * race condition may occur: the first read register may refer to one LLI |
| * whereas the second read may refer to a later LLI in the list because of the |
| * DMA transfer progression inbetween the two reads. |
| * |
| * One solution could have been to pause the DMA transfer, read the DSCR and |
| * CTRLA then resume the DMA transfer. Nonetheless, this approach presents some |
| * drawbacks: |
| * - If the DMA transfer is paused, RX overruns or TX underruns are more likey |
| * to occur depending on the system latency. Taking the USART driver as an |
| * example, it uses a cyclic DMA transfer to read data from the Receive |
| * Holding Register (RHR) to avoid RX overruns since the RHR is not protected |
| * by any FIFO on most Atmel SoCs. So pausing the DMA transfer to compute the |
| * residue would break the USART driver design. |
| * - The atc_pause() function masks interrupts but we'd rather avoid to do so |
| * for system latency purpose. |
| * |
| * Then we'd rather use another solution: the DSCR is read a first time, the |
| * CTRLA is read in turn, next the DSCR is read a second time. If the two |
| * consecutive read values of the DSCR are the same then we assume both refers |
| * to the very same LLI as well as the CTRLA value read inbetween does. For |
| * cyclic transfers, the assumption is that a full loop is "not so fast". If the |
| * two DSCR values are different, we read again the CTRLA then the DSCR till two |
| * consecutive read values from DSCR are equal or till the maximum trials is |
| * reach. This algorithm is very unlikely not to find a stable value for DSCR. |
| * |
| * Returns: %0 on success, -errno otherwise. |
| */ |
| static int atc_get_llis_residue(struct at_dma_chan *atchan, |
| struct at_desc *desc, u32 *residue) |
| { |
| u32 len, ctrla, dscr; |
| unsigned int i; |
| |
| len = desc->total_len; |
| dscr = channel_readl(atchan, DSCR); |
| rmb(); /* ensure DSCR is read before CTRLA */ |
| ctrla = channel_readl(atchan, CTRLA); |
| for (i = 0; i < ATC_MAX_DSCR_TRIALS; ++i) { |
| u32 new_dscr; |
| |
| rmb(); /* ensure DSCR is read after CTRLA */ |
| new_dscr = channel_readl(atchan, DSCR); |
| |
| /* |
| * If the DSCR register value has not changed inside the DMA |
| * controller since the previous read, we assume that both the |
| * dscr and ctrla values refers to the very same descriptor. |
| */ |
| if (likely(new_dscr == dscr)) |
| break; |
| |
| /* |
| * DSCR has changed inside the DMA controller, so the previously |
| * read value of CTRLA may refer to an already processed |
| * descriptor hence could be outdated. We need to update ctrla |
| * to match the current descriptor. |
| */ |
| dscr = new_dscr; |
| rmb(); /* ensure DSCR is read before CTRLA */ |
| ctrla = channel_readl(atchan, CTRLA); |
| } |
| if (unlikely(i == ATC_MAX_DSCR_TRIALS)) |
| return -ETIMEDOUT; |
| |
| /* For the first descriptor we can be more accurate. */ |
| if (desc->sg[0].lli->dscr == dscr) { |
| *residue = atc_calc_bytes_left(len, ctrla); |
| return 0; |
| } |
| len -= desc->sg[0].len; |
| |
| for (i = 1; i < desc->sglen; i++) { |
| if (desc->sg[i].lli && desc->sg[i].lli->dscr == dscr) |
| break; |
| len -= desc->sg[i].len; |
| } |
| |
| /* |
| * For the current LLI in the chain we can calculate the remaining bytes |
| * using the channel's CTRLA register. |
| */ |
| *residue = atc_calc_bytes_left(len, ctrla); |
| return 0; |
| |
| } |
| |
| /** |
| * atc_get_residue - get the number of bytes residue for a cookie. |
| * The residue is passed by address and updated on success. |
| * @chan: DMA channel |
| * @cookie: transaction identifier to check status of |
| * @residue: residue to be updated. |
| * |
| * Return: %0 on success, -errno otherwise. |
| */ |
| static int atc_get_residue(struct dma_chan *chan, dma_cookie_t cookie, |
| u32 *residue) |
| { |
| struct at_dma_chan *atchan = to_at_dma_chan(chan); |
| struct virt_dma_desc *vd; |
| struct at_desc *desc = NULL; |
| u32 len, ctrla; |
| |
| vd = vchan_find_desc(&atchan->vc, cookie); |
| if (vd) |
| desc = to_atdma_desc(&vd->tx); |
| else if (atchan->desc && atchan->desc->vd.tx.cookie == cookie) |
| desc = atchan->desc; |
| |
| if (!desc) |
| return -EINVAL; |
| |
| if (desc->sg[0].lli->dscr) |
| /* hardware linked list transfer */ |
| return atc_get_llis_residue(atchan, desc, residue); |
| |
| /* single transfer */ |
| len = desc->total_len; |
| ctrla = channel_readl(atchan, CTRLA); |
| *residue = atc_calc_bytes_left(len, ctrla); |
| return 0; |
| } |
| |
| /** |
| * atc_handle_error - handle errors reported by DMA controller |
| * @atchan: channel where error occurs. |
| * @i: channel index |
| */ |
| static void atc_handle_error(struct at_dma_chan *atchan, unsigned int i) |
| { |
| struct at_desc *desc = atchan->desc; |
| |
| /* Disable channel on AHB error */ |
| dma_writel(atchan->atdma, CHDR, AT_DMA_RES(i) | atchan->mask); |
| |
| /* |
| * KERN_CRITICAL may seem harsh, but since this only happens |
| * when someone submits a bad physical address in a |
| * descriptor, we should consider ourselves lucky that the |
| * controller flagged an error instead of scribbling over |
| * random memory locations. |
| */ |
| dev_crit(chan2dev(&atchan->vc.chan), "Bad descriptor submitted for DMA!\n"); |
| dev_crit(chan2dev(&atchan->vc.chan), "cookie: %d\n", |
| desc->vd.tx.cookie); |
| for (i = 0; i < desc->sglen; i++) |
| atc_dump_lli(atchan, desc->sg[i].lli); |
| } |
| |
| static void atdma_handle_chan_done(struct at_dma_chan *atchan, u32 pending, |
| unsigned int i) |
| { |
| struct at_desc *desc; |
| |
| spin_lock(&atchan->vc.lock); |
| desc = atchan->desc; |
| |
| if (desc) { |
| if (pending & AT_DMA_ERR(i)) { |
| atc_handle_error(atchan, i); |
| /* Pretend the descriptor completed successfully */ |
| } |
| |
| if (atc_chan_is_cyclic(atchan)) { |
| vchan_cyclic_callback(&desc->vd); |
| } else { |
| vchan_cookie_complete(&desc->vd); |
| atchan->desc = NULL; |
| if (!(atc_chan_is_enabled(atchan))) |
| atc_dostart(atchan); |
| } |
| } |
| spin_unlock(&atchan->vc.lock); |
| } |
| |
| static irqreturn_t at_dma_interrupt(int irq, void *dev_id) |
| { |
| struct at_dma *atdma = dev_id; |
| struct at_dma_chan *atchan; |
| int i; |
| u32 status, pending, imr; |
| int ret = IRQ_NONE; |
| |
| do { |
| imr = dma_readl(atdma, EBCIMR); |
| status = dma_readl(atdma, EBCISR); |
| pending = status & imr; |
| |
| if (!pending) |
| break; |
| |
| dev_vdbg(atdma->dma_device.dev, |
| "interrupt: status = 0x%08x, 0x%08x, 0x%08x\n", |
| status, imr, pending); |
| |
| for (i = 0; i < atdma->dma_device.chancnt; i++) { |
| atchan = &atdma->chan[i]; |
| if (!(pending & (AT_DMA_BTC(i) | AT_DMA_ERR(i)))) |
| continue; |
| atdma_handle_chan_done(atchan, pending, i); |
| ret = IRQ_HANDLED; |
| } |
| |
| } while (pending); |
| |
| return ret; |
| } |
| |
| /*-- DMA Engine API --------------------------------------------------*/ |
| /** |
| * atc_prep_dma_interleaved - prepare memory to memory interleaved operation |
| * @chan: the channel to prepare operation on |
| * @xt: Interleaved transfer template |
| * @flags: tx descriptor status flags |
| */ |
| static struct dma_async_tx_descriptor * |
| atc_prep_dma_interleaved(struct dma_chan *chan, |
| struct dma_interleaved_template *xt, |
| unsigned long flags) |
| { |
| struct at_dma *atdma = to_at_dma(chan->device); |
| struct at_dma_chan *atchan = to_at_dma_chan(chan); |
| struct data_chunk *first; |
| struct atdma_sg *atdma_sg; |
| struct at_desc *desc; |
| struct at_lli *lli; |
| size_t xfer_count; |
| unsigned int dwidth; |
| u32 ctrla; |
| u32 ctrlb; |
| size_t len = 0; |
| int i; |
| |
| if (unlikely(!xt || xt->numf != 1 || !xt->frame_size)) |
| return NULL; |
| |
| first = xt->sgl; |
| |
| dev_info(chan2dev(chan), |
| "%s: src=%pad, dest=%pad, numf=%d, frame_size=%d, flags=0x%lx\n", |
| __func__, &xt->src_start, &xt->dst_start, xt->numf, |
| xt->frame_size, flags); |
| |
| /* |
| * The controller can only "skip" X bytes every Y bytes, so we |
| * need to make sure we are given a template that fit that |
| * description, ie a template with chunks that always have the |
| * same size, with the same ICGs. |
| */ |
| for (i = 0; i < xt->frame_size; i++) { |
| struct data_chunk *chunk = xt->sgl + i; |
| |
| if ((chunk->size != xt->sgl->size) || |
| (dmaengine_get_dst_icg(xt, chunk) != dmaengine_get_dst_icg(xt, first)) || |
| (dmaengine_get_src_icg(xt, chunk) != dmaengine_get_src_icg(xt, first))) { |
| dev_err(chan2dev(chan), |
| "%s: the controller can transfer only identical chunks\n", |
| __func__); |
| return NULL; |
| } |
| |
| len += chunk->size; |
| } |
| |
| dwidth = atc_get_xfer_width(xt->src_start, xt->dst_start, len); |
| |
| xfer_count = len >> dwidth; |
| if (xfer_count > ATC_BTSIZE_MAX) { |
| dev_err(chan2dev(chan), "%s: buffer is too big\n", __func__); |
| return NULL; |
| } |
| |
| ctrla = FIELD_PREP(ATC_SRC_WIDTH, dwidth) | |
| FIELD_PREP(ATC_DST_WIDTH, dwidth); |
| |
| ctrlb = ATC_DEFAULT_CTRLB | ATC_IEN | |
| FIELD_PREP(ATC_SRC_ADDR_MODE, ATC_SRC_ADDR_MODE_INCR) | |
| FIELD_PREP(ATC_DST_ADDR_MODE, ATC_DST_ADDR_MODE_INCR) | |
| ATC_SRC_PIP | ATC_DST_PIP | |
| FIELD_PREP(ATC_FC, ATC_FC_MEM2MEM); |
| |
| desc = kzalloc(struct_size(desc, sg, 1), GFP_ATOMIC); |
| if (!desc) |
| return NULL; |
| desc->sglen = 1; |
| |
| atdma_sg = desc->sg; |
| atdma_sg->lli = dma_pool_alloc(atdma->lli_pool, GFP_NOWAIT, |
| &atdma_sg->lli_phys); |
| if (!atdma_sg->lli) { |
| kfree(desc); |
| return NULL; |
| } |
| lli = atdma_sg->lli; |
| |
| lli->saddr = xt->src_start; |
| lli->daddr = xt->dst_start; |
| lli->ctrla = ctrla | xfer_count; |
| lli->ctrlb = ctrlb; |
| |
| desc->boundary = first->size >> dwidth; |
| desc->dst_hole = (dmaengine_get_dst_icg(xt, first) >> dwidth) + 1; |
| desc->src_hole = (dmaengine_get_src_icg(xt, first) >> dwidth) + 1; |
| |
| atdma_sg->len = len; |
| desc->total_len = len; |
| |
| set_lli_eol(desc, 0); |
| return vchan_tx_prep(&atchan->vc, &desc->vd, flags); |
| } |
| |
| /** |
| * atc_prep_dma_memcpy - prepare a memcpy operation |
| * @chan: the channel to prepare operation on |
| * @dest: operation virtual destination address |
| * @src: operation virtual source address |
| * @len: operation length |
| * @flags: tx descriptor status flags |
| */ |
| static struct dma_async_tx_descriptor * |
| atc_prep_dma_memcpy(struct dma_chan *chan, dma_addr_t dest, dma_addr_t src, |
| size_t len, unsigned long flags) |
| { |
| struct at_dma *atdma = to_at_dma(chan->device); |
| struct at_dma_chan *atchan = to_at_dma_chan(chan); |
| struct at_desc *desc = NULL; |
| size_t xfer_count; |
| size_t offset; |
| size_t sg_len; |
| unsigned int src_width; |
| unsigned int dst_width; |
| unsigned int i; |
| u32 ctrla; |
| u32 ctrlb; |
| |
| dev_dbg(chan2dev(chan), "prep_dma_memcpy: d%pad s%pad l0x%zx f0x%lx\n", |
| &dest, &src, len, flags); |
| |
| if (unlikely(!len)) { |
| dev_err(chan2dev(chan), "prep_dma_memcpy: length is zero!\n"); |
| return NULL; |
| } |
| |
| sg_len = DIV_ROUND_UP(len, ATC_BTSIZE_MAX); |
| desc = kzalloc(struct_size(desc, sg, sg_len), GFP_ATOMIC); |
| if (!desc) |
| return NULL; |
| desc->sglen = sg_len; |
| |
| ctrlb = ATC_DEFAULT_CTRLB | ATC_IEN | |
| FIELD_PREP(ATC_SRC_ADDR_MODE, ATC_SRC_ADDR_MODE_INCR) | |
| FIELD_PREP(ATC_DST_ADDR_MODE, ATC_DST_ADDR_MODE_INCR) | |
| FIELD_PREP(ATC_FC, ATC_FC_MEM2MEM); |
| |
| /* |
| * We can be a lot more clever here, but this should take care |
| * of the most common optimization. |
| */ |
| src_width = dst_width = atc_get_xfer_width(src, dest, len); |
| |
| ctrla = FIELD_PREP(ATC_SRC_WIDTH, src_width) | |
| FIELD_PREP(ATC_DST_WIDTH, dst_width); |
| |
| for (offset = 0, i = 0; offset < len; |
| offset += xfer_count << src_width, i++) { |
| struct atdma_sg *atdma_sg = &desc->sg[i]; |
| struct at_lli *lli; |
| |
| atdma_sg->lli = dma_pool_alloc(atdma->lli_pool, GFP_NOWAIT, |
| &atdma_sg->lli_phys); |
| if (!atdma_sg->lli) |
| goto err_desc_get; |
| lli = atdma_sg->lli; |
| |
| xfer_count = min_t(size_t, (len - offset) >> src_width, |
| ATC_BTSIZE_MAX); |
| |
| lli->saddr = src + offset; |
| lli->daddr = dest + offset; |
| lli->ctrla = ctrla | xfer_count; |
| lli->ctrlb = ctrlb; |
| |
| desc->sg[i].len = xfer_count << src_width; |
| |
| atdma_lli_chain(desc, i); |
| } |
| |
| desc->total_len = len; |
| |
| /* set end-of-link to the last link descriptor of list*/ |
| set_lli_eol(desc, i - 1); |
| |
| return vchan_tx_prep(&atchan->vc, &desc->vd, flags); |
| |
| err_desc_get: |
| atdma_desc_free(&desc->vd); |
| return NULL; |
| } |
| |
| static int atdma_create_memset_lli(struct dma_chan *chan, |
| struct atdma_sg *atdma_sg, |
| dma_addr_t psrc, dma_addr_t pdst, size_t len) |
| { |
| struct at_dma *atdma = to_at_dma(chan->device); |
| struct at_lli *lli; |
| size_t xfer_count; |
| u32 ctrla = FIELD_PREP(ATC_SRC_WIDTH, 2) | FIELD_PREP(ATC_DST_WIDTH, 2); |
| u32 ctrlb = ATC_DEFAULT_CTRLB | ATC_IEN | |
| FIELD_PREP(ATC_SRC_ADDR_MODE, ATC_SRC_ADDR_MODE_FIXED) | |
| FIELD_PREP(ATC_DST_ADDR_MODE, ATC_DST_ADDR_MODE_INCR) | |
| FIELD_PREP(ATC_FC, ATC_FC_MEM2MEM); |
| |
| xfer_count = len >> 2; |
| if (xfer_count > ATC_BTSIZE_MAX) { |
| dev_err(chan2dev(chan), "%s: buffer is too big\n", __func__); |
| return -EINVAL; |
| } |
| |
| atdma_sg->lli = dma_pool_alloc(atdma->lli_pool, GFP_NOWAIT, |
| &atdma_sg->lli_phys); |
| if (!atdma_sg->lli) |
| return -ENOMEM; |
| lli = atdma_sg->lli; |
| |
| lli->saddr = psrc; |
| lli->daddr = pdst; |
| lli->ctrla = ctrla | xfer_count; |
| lli->ctrlb = ctrlb; |
| |
| atdma_sg->len = len; |
| |
| return 0; |
| } |
| |
| /** |
| * atc_prep_dma_memset - prepare a memcpy operation |
| * @chan: the channel to prepare operation on |
| * @dest: operation virtual destination address |
| * @value: value to set memory buffer to |
| * @len: operation length |
| * @flags: tx descriptor status flags |
| */ |
| static struct dma_async_tx_descriptor * |
| atc_prep_dma_memset(struct dma_chan *chan, dma_addr_t dest, int value, |
| size_t len, unsigned long flags) |
| { |
| struct at_dma_chan *atchan = to_at_dma_chan(chan); |
| struct at_dma *atdma = to_at_dma(chan->device); |
| struct at_desc *desc; |
| void __iomem *vaddr; |
| dma_addr_t paddr; |
| char fill_pattern; |
| int ret; |
| |
| dev_vdbg(chan2dev(chan), "%s: d%pad v0x%x l0x%zx f0x%lx\n", __func__, |
| &dest, value, len, flags); |
| |
| if (unlikely(!len)) { |
| dev_dbg(chan2dev(chan), "%s: length is zero!\n", __func__); |
| return NULL; |
| } |
| |
| if (!is_dma_fill_aligned(chan->device, dest, 0, len)) { |
| dev_dbg(chan2dev(chan), "%s: buffer is not aligned\n", |
| __func__); |
| return NULL; |
| } |
| |
| vaddr = dma_pool_alloc(atdma->memset_pool, GFP_NOWAIT, &paddr); |
| if (!vaddr) { |
| dev_err(chan2dev(chan), "%s: couldn't allocate buffer\n", |
| __func__); |
| return NULL; |
| } |
| |
| /* Only the first byte of value is to be used according to dmaengine */ |
| fill_pattern = (char)value; |
| |
| *(u32*)vaddr = (fill_pattern << 24) | |
| (fill_pattern << 16) | |
| (fill_pattern << 8) | |
| fill_pattern; |
| |
| desc = kzalloc(struct_size(desc, sg, 1), GFP_ATOMIC); |
| if (!desc) |
| goto err_free_buffer; |
| desc->sglen = 1; |
| |
| ret = atdma_create_memset_lli(chan, desc->sg, paddr, dest, len); |
| if (ret) |
| goto err_free_desc; |
| |
| desc->memset_paddr = paddr; |
| desc->memset_vaddr = vaddr; |
| desc->memset_buffer = true; |
| |
| desc->total_len = len; |
| |
| /* set end-of-link on the descriptor */ |
| set_lli_eol(desc, 0); |
| |
| return vchan_tx_prep(&atchan->vc, &desc->vd, flags); |
| |
| err_free_desc: |
| kfree(desc); |
| err_free_buffer: |
| dma_pool_free(atdma->memset_pool, vaddr, paddr); |
| return NULL; |
| } |
| |
| static struct dma_async_tx_descriptor * |
| atc_prep_dma_memset_sg(struct dma_chan *chan, |
| struct scatterlist *sgl, |
| unsigned int sg_len, int value, |
| unsigned long flags) |
| { |
| struct at_dma_chan *atchan = to_at_dma_chan(chan); |
| struct at_dma *atdma = to_at_dma(chan->device); |
| struct at_desc *desc; |
| struct scatterlist *sg; |
| void __iomem *vaddr; |
| dma_addr_t paddr; |
| size_t total_len = 0; |
| int i; |
| int ret; |
| |
| dev_vdbg(chan2dev(chan), "%s: v0x%x l0x%zx f0x%lx\n", __func__, |
| value, sg_len, flags); |
| |
| if (unlikely(!sgl || !sg_len)) { |
| dev_dbg(chan2dev(chan), "%s: scatterlist is empty!\n", |
| __func__); |
| return NULL; |
| } |
| |
| vaddr = dma_pool_alloc(atdma->memset_pool, GFP_NOWAIT, &paddr); |
| if (!vaddr) { |
| dev_err(chan2dev(chan), "%s: couldn't allocate buffer\n", |
| __func__); |
| return NULL; |
| } |
| *(u32*)vaddr = value; |
| |
| desc = kzalloc(struct_size(desc, sg, sg_len), GFP_ATOMIC); |
| if (!desc) |
| goto err_free_dma_buf; |
| desc->sglen = sg_len; |
| |
| for_each_sg(sgl, sg, sg_len, i) { |
| dma_addr_t dest = sg_dma_address(sg); |
| size_t len = sg_dma_len(sg); |
| |
| dev_vdbg(chan2dev(chan), "%s: d%pad, l0x%zx\n", |
| __func__, &dest, len); |
| |
| if (!is_dma_fill_aligned(chan->device, dest, 0, len)) { |
| dev_err(chan2dev(chan), "%s: buffer is not aligned\n", |
| __func__); |
| goto err_free_desc; |
| } |
| |
| ret = atdma_create_memset_lli(chan, &desc->sg[i], paddr, dest, |
| len); |
| if (ret) |
| goto err_free_desc; |
| |
| atdma_lli_chain(desc, i); |
| total_len += len; |
| } |
| |
| desc->memset_paddr = paddr; |
| desc->memset_vaddr = vaddr; |
| desc->memset_buffer = true; |
| |
| desc->total_len = total_len; |
| |
| /* set end-of-link on the descriptor */ |
| set_lli_eol(desc, i - 1); |
| |
| return vchan_tx_prep(&atchan->vc, &desc->vd, flags); |
| |
| err_free_desc: |
| atdma_desc_free(&desc->vd); |
| err_free_dma_buf: |
| dma_pool_free(atdma->memset_pool, vaddr, paddr); |
| return NULL; |
| } |
| |
| /** |
| * atc_prep_slave_sg - prepare descriptors for a DMA_SLAVE transaction |
| * @chan: DMA channel |
| * @sgl: scatterlist to transfer to/from |
| * @sg_len: number of entries in @scatterlist |
| * @direction: DMA direction |
| * @flags: tx descriptor status flags |
| * @context: transaction context (ignored) |
| */ |
| static struct dma_async_tx_descriptor * |
| atc_prep_slave_sg(struct dma_chan *chan, struct scatterlist *sgl, |
| unsigned int sg_len, enum dma_transfer_direction direction, |
| unsigned long flags, void *context) |
| { |
| struct at_dma *atdma = to_at_dma(chan->device); |
| struct at_dma_chan *atchan = to_at_dma_chan(chan); |
| struct at_dma_slave *atslave = chan->private; |
| struct dma_slave_config *sconfig = &atchan->dma_sconfig; |
| struct at_desc *desc; |
| u32 ctrla; |
| u32 ctrlb; |
| dma_addr_t reg; |
| unsigned int reg_width; |
| unsigned int mem_width; |
| unsigned int i; |
| struct scatterlist *sg; |
| size_t total_len = 0; |
| |
| dev_vdbg(chan2dev(chan), "prep_slave_sg (%d): %s f0x%lx\n", |
| sg_len, |
| direction == DMA_MEM_TO_DEV ? "TO DEVICE" : "FROM DEVICE", |
| flags); |
| |
| if (unlikely(!atslave || !sg_len)) { |
| dev_dbg(chan2dev(chan), "prep_slave_sg: sg length is zero!\n"); |
| return NULL; |
| } |
| |
| desc = kzalloc(struct_size(desc, sg, sg_len), GFP_ATOMIC); |
| if (!desc) |
| return NULL; |
| desc->sglen = sg_len; |
| |
| ctrla = FIELD_PREP(ATC_SCSIZE, sconfig->src_maxburst) | |
| FIELD_PREP(ATC_DCSIZE, sconfig->dst_maxburst); |
| ctrlb = ATC_IEN; |
| |
| switch (direction) { |
| case DMA_MEM_TO_DEV: |
| reg_width = convert_buswidth(sconfig->dst_addr_width); |
| ctrla |= FIELD_PREP(ATC_DST_WIDTH, reg_width); |
| ctrlb |= FIELD_PREP(ATC_DST_ADDR_MODE, |
| ATC_DST_ADDR_MODE_FIXED) | |
| FIELD_PREP(ATC_SRC_ADDR_MODE, ATC_SRC_ADDR_MODE_INCR) | |
| FIELD_PREP(ATC_FC, ATC_FC_MEM2PER) | |
| FIELD_PREP(ATC_SIF, atchan->mem_if) | |
| FIELD_PREP(ATC_DIF, atchan->per_if); |
| reg = sconfig->dst_addr; |
| for_each_sg(sgl, sg, sg_len, i) { |
| struct atdma_sg *atdma_sg = &desc->sg[i]; |
| struct at_lli *lli; |
| u32 len; |
| u32 mem; |
| |
| atdma_sg->lli = dma_pool_alloc(atdma->lli_pool, |
| GFP_NOWAIT, |
| &atdma_sg->lli_phys); |
| if (!atdma_sg->lli) |
| goto err_desc_get; |
| lli = atdma_sg->lli; |
| |
| mem = sg_dma_address(sg); |
| len = sg_dma_len(sg); |
| if (unlikely(!len)) { |
| dev_dbg(chan2dev(chan), |
| "prep_slave_sg: sg(%d) data length is zero\n", i); |
| goto err; |
| } |
| mem_width = 2; |
| if (unlikely(mem & 3 || len & 3)) |
| mem_width = 0; |
| |
| lli->saddr = mem; |
| lli->daddr = reg; |
| lli->ctrla = ctrla | |
| FIELD_PREP(ATC_SRC_WIDTH, mem_width) | |
| len >> mem_width; |
| lli->ctrlb = ctrlb; |
| |
| atdma_sg->len = len; |
| total_len += len; |
| |
| desc->sg[i].len = len; |
| atdma_lli_chain(desc, i); |
| } |
| break; |
| case DMA_DEV_TO_MEM: |
| reg_width = convert_buswidth(sconfig->src_addr_width); |
| ctrla |= FIELD_PREP(ATC_SRC_WIDTH, reg_width); |
| ctrlb |= FIELD_PREP(ATC_DST_ADDR_MODE, ATC_DST_ADDR_MODE_INCR) | |
| FIELD_PREP(ATC_SRC_ADDR_MODE, |
| ATC_SRC_ADDR_MODE_FIXED) | |
| FIELD_PREP(ATC_FC, ATC_FC_PER2MEM) | |
| FIELD_PREP(ATC_SIF, atchan->per_if) | |
| FIELD_PREP(ATC_DIF, atchan->mem_if); |
| |
| reg = sconfig->src_addr; |
| for_each_sg(sgl, sg, sg_len, i) { |
| struct atdma_sg *atdma_sg = &desc->sg[i]; |
| struct at_lli *lli; |
| u32 len; |
| u32 mem; |
| |
| atdma_sg->lli = dma_pool_alloc(atdma->lli_pool, |
| GFP_NOWAIT, |
| &atdma_sg->lli_phys); |
| if (!atdma_sg->lli) |
| goto err_desc_get; |
| lli = atdma_sg->lli; |
| |
| mem = sg_dma_address(sg); |
| len = sg_dma_len(sg); |
| if (unlikely(!len)) { |
| dev_dbg(chan2dev(chan), |
| "prep_slave_sg: sg(%d) data length is zero\n", i); |
| goto err; |
| } |
| mem_width = 2; |
| if (unlikely(mem & 3 || len & 3)) |
| mem_width = 0; |
| |
| lli->saddr = reg; |
| lli->daddr = mem; |
| lli->ctrla = ctrla | |
| FIELD_PREP(ATC_DST_WIDTH, mem_width) | |
| len >> reg_width; |
| lli->ctrlb = ctrlb; |
| |
| desc->sg[i].len = len; |
| total_len += len; |
| |
| atdma_lli_chain(desc, i); |
| } |
| break; |
| default: |
| return NULL; |
| } |
| |
| /* set end-of-link to the last link descriptor of list*/ |
| set_lli_eol(desc, i - 1); |
| |
| desc->total_len = total_len; |
| |
| return vchan_tx_prep(&atchan->vc, &desc->vd, flags); |
| |
| err_desc_get: |
| dev_err(chan2dev(chan), "not enough descriptors available\n"); |
| err: |
| atdma_desc_free(&desc->vd); |
| return NULL; |
| } |
| |
| /* |
| * atc_dma_cyclic_check_values |
| * Check for too big/unaligned periods and unaligned DMA buffer |
| */ |
| static int |
| atc_dma_cyclic_check_values(unsigned int reg_width, dma_addr_t buf_addr, |
| size_t period_len) |
| { |
| if (period_len > (ATC_BTSIZE_MAX << reg_width)) |
| goto err_out; |
| if (unlikely(period_len & ((1 << reg_width) - 1))) |
| goto err_out; |
| if (unlikely(buf_addr & ((1 << reg_width) - 1))) |
| goto err_out; |
| |
| return 0; |
| |
| err_out: |
| return -EINVAL; |
| } |
| |
| /* |
| * atc_dma_cyclic_fill_desc - Fill one period descriptor |
| */ |
| static int |
| atc_dma_cyclic_fill_desc(struct dma_chan *chan, struct at_desc *desc, |
| unsigned int i, dma_addr_t buf_addr, |
| unsigned int reg_width, size_t period_len, |
| enum dma_transfer_direction direction) |
| { |
| struct at_dma *atdma = to_at_dma(chan->device); |
| struct at_dma_chan *atchan = to_at_dma_chan(chan); |
| struct dma_slave_config *sconfig = &atchan->dma_sconfig; |
| struct atdma_sg *atdma_sg = &desc->sg[i]; |
| struct at_lli *lli; |
| |
| atdma_sg->lli = dma_pool_alloc(atdma->lli_pool, GFP_ATOMIC, |
| &atdma_sg->lli_phys); |
| if (!atdma_sg->lli) |
| return -ENOMEM; |
| lli = atdma_sg->lli; |
| |
| switch (direction) { |
| case DMA_MEM_TO_DEV: |
| lli->saddr = buf_addr + (period_len * i); |
| lli->daddr = sconfig->dst_addr; |
| lli->ctrlb = FIELD_PREP(ATC_DST_ADDR_MODE, |
| ATC_DST_ADDR_MODE_FIXED) | |
| FIELD_PREP(ATC_SRC_ADDR_MODE, |
| ATC_SRC_ADDR_MODE_INCR) | |
| FIELD_PREP(ATC_FC, ATC_FC_MEM2PER) | |
| FIELD_PREP(ATC_SIF, atchan->mem_if) | |
| FIELD_PREP(ATC_DIF, atchan->per_if); |
| |
| break; |
| |
| case DMA_DEV_TO_MEM: |
| lli->saddr = sconfig->src_addr; |
| lli->daddr = buf_addr + (period_len * i); |
| lli->ctrlb = FIELD_PREP(ATC_DST_ADDR_MODE, |
| ATC_DST_ADDR_MODE_INCR) | |
| FIELD_PREP(ATC_SRC_ADDR_MODE, |
| ATC_SRC_ADDR_MODE_FIXED) | |
| FIELD_PREP(ATC_FC, ATC_FC_PER2MEM) | |
| FIELD_PREP(ATC_SIF, atchan->per_if) | |
| FIELD_PREP(ATC_DIF, atchan->mem_if); |
| break; |
| |
| default: |
| return -EINVAL; |
| } |
| |
| lli->ctrla = FIELD_PREP(ATC_SCSIZE, sconfig->src_maxburst) | |
| FIELD_PREP(ATC_DCSIZE, sconfig->dst_maxburst) | |
| FIELD_PREP(ATC_DST_WIDTH, reg_width) | |
| FIELD_PREP(ATC_SRC_WIDTH, reg_width) | |
| period_len >> reg_width; |
| desc->sg[i].len = period_len; |
| |
| return 0; |
| } |
| |
| /** |
| * atc_prep_dma_cyclic - prepare the cyclic DMA transfer |
| * @chan: the DMA channel to prepare |
| * @buf_addr: physical DMA address where the buffer starts |
| * @buf_len: total number of bytes for the entire buffer |
| * @period_len: number of bytes for each period |
| * @direction: transfer direction, to or from device |
| * @flags: tx descriptor status flags |
| */ |
| static struct dma_async_tx_descriptor * |
| atc_prep_dma_cyclic(struct dma_chan *chan, dma_addr_t buf_addr, size_t buf_len, |
| size_t period_len, enum dma_transfer_direction direction, |
| unsigned long flags) |
| { |
| struct at_dma_chan *atchan = to_at_dma_chan(chan); |
| struct at_dma_slave *atslave = chan->private; |
| struct dma_slave_config *sconfig = &atchan->dma_sconfig; |
| struct at_desc *desc; |
| unsigned long was_cyclic; |
| unsigned int reg_width; |
| unsigned int periods = buf_len / period_len; |
| unsigned int i; |
| |
| dev_vdbg(chan2dev(chan), "prep_dma_cyclic: %s buf@%pad - %d (%d/%d)\n", |
| direction == DMA_MEM_TO_DEV ? "TO DEVICE" : "FROM DEVICE", |
| &buf_addr, |
| periods, buf_len, period_len); |
| |
| if (unlikely(!atslave || !buf_len || !period_len)) { |
| dev_dbg(chan2dev(chan), "prep_dma_cyclic: length is zero!\n"); |
| return NULL; |
| } |
| |
| was_cyclic = test_and_set_bit(ATC_IS_CYCLIC, &atchan->status); |
| if (was_cyclic) { |
| dev_dbg(chan2dev(chan), "prep_dma_cyclic: channel in use!\n"); |
| return NULL; |
| } |
| |
| if (unlikely(!is_slave_direction(direction))) |
| goto err_out; |
| |
| if (direction == DMA_MEM_TO_DEV) |
| reg_width = convert_buswidth(sconfig->dst_addr_width); |
| else |
| reg_width = convert_buswidth(sconfig->src_addr_width); |
| |
| /* Check for too big/unaligned periods and unaligned DMA buffer */ |
| if (atc_dma_cyclic_check_values(reg_width, buf_addr, period_len)) |
| goto err_out; |
| |
| desc = kzalloc(struct_size(desc, sg, periods), GFP_ATOMIC); |
| if (!desc) |
| goto err_out; |
| desc->sglen = periods; |
| |
| /* build cyclic linked list */ |
| for (i = 0; i < periods; i++) { |
| if (atc_dma_cyclic_fill_desc(chan, desc, i, buf_addr, |
| reg_width, period_len, direction)) |
| goto err_fill_desc; |
| atdma_lli_chain(desc, i); |
| } |
| desc->total_len = buf_len; |
| /* lets make a cyclic list */ |
| desc->sg[i - 1].lli->dscr = desc->sg[0].lli_phys; |
| |
| return vchan_tx_prep(&atchan->vc, &desc->vd, flags); |
| |
| err_fill_desc: |
| atdma_desc_free(&desc->vd); |
| err_out: |
| clear_bit(ATC_IS_CYCLIC, &atchan->status); |
| return NULL; |
| } |
| |
| static int atc_config(struct dma_chan *chan, |
| struct dma_slave_config *sconfig) |
| { |
| struct at_dma_chan *atchan = to_at_dma_chan(chan); |
| |
| dev_vdbg(chan2dev(chan), "%s\n", __func__); |
| |
| /* Check if it is chan is configured for slave transfers */ |
| if (!chan->private) |
| return -EINVAL; |
| |
| memcpy(&atchan->dma_sconfig, sconfig, sizeof(*sconfig)); |
| |
| convert_burst(&atchan->dma_sconfig.src_maxburst); |
| convert_burst(&atchan->dma_sconfig.dst_maxburst); |
| |
| return 0; |
| } |
| |
| static int atc_pause(struct dma_chan *chan) |
| { |
| struct at_dma_chan *atchan = to_at_dma_chan(chan); |
| struct at_dma *atdma = to_at_dma(chan->device); |
| int chan_id = atchan->vc.chan.chan_id; |
| unsigned long flags; |
| |
| dev_vdbg(chan2dev(chan), "%s\n", __func__); |
| |
| spin_lock_irqsave(&atchan->vc.lock, flags); |
| |
| dma_writel(atdma, CHER, AT_DMA_SUSP(chan_id)); |
| set_bit(ATC_IS_PAUSED, &atchan->status); |
| |
| spin_unlock_irqrestore(&atchan->vc.lock, flags); |
| |
| return 0; |
| } |
| |
| static int atc_resume(struct dma_chan *chan) |
| { |
| struct at_dma_chan *atchan = to_at_dma_chan(chan); |
| struct at_dma *atdma = to_at_dma(chan->device); |
| int chan_id = atchan->vc.chan.chan_id; |
| unsigned long flags; |
| |
| dev_vdbg(chan2dev(chan), "%s\n", __func__); |
| |
| if (!atc_chan_is_paused(atchan)) |
| return 0; |
| |
| spin_lock_irqsave(&atchan->vc.lock, flags); |
| |
| dma_writel(atdma, CHDR, AT_DMA_RES(chan_id)); |
| clear_bit(ATC_IS_PAUSED, &atchan->status); |
| |
| spin_unlock_irqrestore(&atchan->vc.lock, flags); |
| |
| return 0; |
| } |
| |
| static int atc_terminate_all(struct dma_chan *chan) |
| { |
| struct at_dma_chan *atchan = to_at_dma_chan(chan); |
| struct at_dma *atdma = to_at_dma(chan->device); |
| int chan_id = atchan->vc.chan.chan_id; |
| unsigned long flags; |
| |
| LIST_HEAD(list); |
| |
| dev_vdbg(chan2dev(chan), "%s\n", __func__); |
| |
| /* |
| * This is only called when something went wrong elsewhere, so |
| * we don't really care about the data. Just disable the |
| * channel. We still have to poll the channel enable bit due |
| * to AHB/HSB limitations. |
| */ |
| spin_lock_irqsave(&atchan->vc.lock, flags); |
| |
| /* disabling channel: must also remove suspend state */ |
| dma_writel(atdma, CHDR, AT_DMA_RES(chan_id) | atchan->mask); |
| |
| /* confirm that this channel is disabled */ |
| while (dma_readl(atdma, CHSR) & atchan->mask) |
| cpu_relax(); |
| |
| if (atchan->desc) { |
| vchan_terminate_vdesc(&atchan->desc->vd); |
| atchan->desc = NULL; |
| } |
| |
| vchan_get_all_descriptors(&atchan->vc, &list); |
| |
| clear_bit(ATC_IS_PAUSED, &atchan->status); |
| /* if channel dedicated to cyclic operations, free it */ |
| clear_bit(ATC_IS_CYCLIC, &atchan->status); |
| |
| spin_unlock_irqrestore(&atchan->vc.lock, flags); |
| |
| vchan_dma_desc_free_list(&atchan->vc, &list); |
| |
| return 0; |
| } |
| |
| /** |
| * atc_tx_status - poll for transaction completion |
| * @chan: DMA channel |
| * @cookie: transaction identifier to check status of |
| * @txstate: if not %NULL updated with transaction state |
| * |
| * If @txstate is passed in, upon return it reflect the driver |
| * internal state and can be used with dma_async_is_complete() to check |
| * the status of multiple cookies without re-checking hardware state. |
| */ |
| static enum dma_status |
| atc_tx_status(struct dma_chan *chan, |
| dma_cookie_t cookie, |
| struct dma_tx_state *txstate) |
| { |
| struct at_dma_chan *atchan = to_at_dma_chan(chan); |
| unsigned long flags; |
| enum dma_status dma_status; |
| u32 residue; |
| int ret; |
| |
| dma_status = dma_cookie_status(chan, cookie, txstate); |
| if (dma_status == DMA_COMPLETE || !txstate) |
| return dma_status; |
| |
| spin_lock_irqsave(&atchan->vc.lock, flags); |
| /* Get number of bytes left in the active transactions */ |
| ret = atc_get_residue(chan, cookie, &residue); |
| spin_unlock_irqrestore(&atchan->vc.lock, flags); |
| |
| if (unlikely(ret < 0)) { |
| dev_vdbg(chan2dev(chan), "get residual bytes error\n"); |
| return DMA_ERROR; |
| } else { |
| dma_set_residue(txstate, residue); |
| } |
| |
| dev_vdbg(chan2dev(chan), "tx_status %d: cookie = %d residue = %u\n", |
| dma_status, cookie, residue); |
| |
| return dma_status; |
| } |
| |
| static void atc_issue_pending(struct dma_chan *chan) |
| { |
| struct at_dma_chan *atchan = to_at_dma_chan(chan); |
| unsigned long flags; |
| |
| spin_lock_irqsave(&atchan->vc.lock, flags); |
| if (vchan_issue_pending(&atchan->vc) && !atchan->desc) { |
| if (!(atc_chan_is_enabled(atchan))) |
| atc_dostart(atchan); |
| } |
| spin_unlock_irqrestore(&atchan->vc.lock, flags); |
| } |
| |
| /** |
| * atc_alloc_chan_resources - allocate resources for DMA channel |
| * @chan: allocate descriptor resources for this channel |
| * |
| * Return: the number of allocated descriptors |
| */ |
| static int atc_alloc_chan_resources(struct dma_chan *chan) |
| { |
| struct at_dma_chan *atchan = to_at_dma_chan(chan); |
| struct at_dma *atdma = to_at_dma(chan->device); |
| struct at_dma_slave *atslave; |
| u32 cfg; |
| |
| dev_vdbg(chan2dev(chan), "alloc_chan_resources\n"); |
| |
| /* ASSERT: channel is idle */ |
| if (atc_chan_is_enabled(atchan)) { |
| dev_dbg(chan2dev(chan), "DMA channel not idle ?\n"); |
| return -EIO; |
| } |
| |
| cfg = ATC_DEFAULT_CFG; |
| |
| atslave = chan->private; |
| if (atslave) { |
| /* |
| * We need controller-specific data to set up slave |
| * transfers. |
| */ |
| BUG_ON(!atslave->dma_dev || atslave->dma_dev != atdma->dma_device.dev); |
| |
| /* if cfg configuration specified take it instead of default */ |
| if (atslave->cfg) |
| cfg = atslave->cfg; |
| } |
| |
| /* channel parameters */ |
| channel_writel(atchan, CFG, cfg); |
| |
| return 0; |
| } |
| |
| /** |
| * atc_free_chan_resources - free all channel resources |
| * @chan: DMA channel |
| */ |
| static void atc_free_chan_resources(struct dma_chan *chan) |
| { |
| struct at_dma_chan *atchan = to_at_dma_chan(chan); |
| |
| BUG_ON(atc_chan_is_enabled(atchan)); |
| |
| vchan_free_chan_resources(to_virt_chan(chan)); |
| atchan->status = 0; |
| |
| /* |
| * Free atslave allocated in at_dma_xlate() |
| */ |
| kfree(chan->private); |
| chan->private = NULL; |
| |
| dev_vdbg(chan2dev(chan), "free_chan_resources: done\n"); |
| } |
| |
| #ifdef CONFIG_OF |
| static bool at_dma_filter(struct dma_chan *chan, void *slave) |
| { |
| struct at_dma_slave *atslave = slave; |
| |
| if (atslave->dma_dev == chan->device->dev) { |
| chan->private = atslave; |
| return true; |
| } else { |
| return false; |
| } |
| } |
| |
| static struct dma_chan *at_dma_xlate(struct of_phandle_args *dma_spec, |
| struct of_dma *of_dma) |
| { |
| struct dma_chan *chan; |
| struct at_dma_chan *atchan; |
| struct at_dma_slave *atslave; |
| dma_cap_mask_t mask; |
| unsigned int per_id; |
| struct platform_device *dmac_pdev; |
| |
| if (dma_spec->args_count != 2) |
| return NULL; |
| |
| dmac_pdev = of_find_device_by_node(dma_spec->np); |
| if (!dmac_pdev) |
| return NULL; |
| |
| dma_cap_zero(mask); |
| dma_cap_set(DMA_SLAVE, mask); |
| |
| atslave = kmalloc(sizeof(*atslave), GFP_KERNEL); |
| if (!atslave) { |
| put_device(&dmac_pdev->dev); |
| return NULL; |
| } |
| |
| atslave->cfg = ATC_DST_H2SEL | ATC_SRC_H2SEL; |
| /* |
| * We can fill both SRC_PER and DST_PER, one of these fields will be |
| * ignored depending on DMA transfer direction. |
| */ |
| per_id = dma_spec->args[1] & AT91_DMA_CFG_PER_ID_MASK; |
| atslave->cfg |= ATC_DST_PER_ID(per_id) | ATC_SRC_PER_ID(per_id); |
| /* |
| * We have to translate the value we get from the device tree since |
| * the half FIFO configuration value had to be 0 to keep backward |
| * compatibility. |
| */ |
| switch (dma_spec->args[1] & AT91_DMA_CFG_FIFOCFG_MASK) { |
| case AT91_DMA_CFG_FIFOCFG_ALAP: |
| atslave->cfg |= FIELD_PREP(ATC_FIFOCFG, |
| ATC_FIFOCFG_LARGESTBURST); |
| break; |
| case AT91_DMA_CFG_FIFOCFG_ASAP: |
| atslave->cfg |= FIELD_PREP(ATC_FIFOCFG, |
| ATC_FIFOCFG_ENOUGHSPACE); |
| break; |
| case AT91_DMA_CFG_FIFOCFG_HALF: |
| default: |
| atslave->cfg |= FIELD_PREP(ATC_FIFOCFG, ATC_FIFOCFG_HALFFIFO); |
| } |
| atslave->dma_dev = &dmac_pdev->dev; |
| |
| chan = dma_request_channel(mask, at_dma_filter, atslave); |
| if (!chan) { |
| put_device(&dmac_pdev->dev); |
| kfree(atslave); |
| return NULL; |
| } |
| |
| atchan = to_at_dma_chan(chan); |
| atchan->per_if = dma_spec->args[0] & 0xff; |
| atchan->mem_if = (dma_spec->args[0] >> 16) & 0xff; |
| |
| return chan; |
| } |
| #else |
| static struct dma_chan *at_dma_xlate(struct of_phandle_args *dma_spec, |
| struct of_dma *of_dma) |
| { |
| return NULL; |
| } |
| #endif |
| |
| /*-- Module Management -----------------------------------------------*/ |
| |
| /* cap_mask is a multi-u32 bitfield, fill it with proper C code. */ |
| static struct at_dma_platform_data at91sam9rl_config = { |
| .nr_channels = 2, |
| }; |
| static struct at_dma_platform_data at91sam9g45_config = { |
| .nr_channels = 8, |
| }; |
| |
| #if defined(CONFIG_OF) |
| static const struct of_device_id atmel_dma_dt_ids[] = { |
| { |
| .compatible = "atmel,at91sam9rl-dma", |
| .data = &at91sam9rl_config, |
| }, { |
| .compatible = "atmel,at91sam9g45-dma", |
| .data = &at91sam9g45_config, |
| }, { |
| /* sentinel */ |
| } |
| }; |
| |
| MODULE_DEVICE_TABLE(of, atmel_dma_dt_ids); |
| #endif |
| |
| static const struct platform_device_id atdma_devtypes[] = { |
| { |
| .name = "at91sam9rl_dma", |
| .driver_data = (unsigned long) &at91sam9rl_config, |
| }, { |
| .name = "at91sam9g45_dma", |
| .driver_data = (unsigned long) &at91sam9g45_config, |
| }, { |
| /* sentinel */ |
| } |
| }; |
| |
| static inline const struct at_dma_platform_data * __init at_dma_get_driver_data( |
| struct platform_device *pdev) |
| { |
| if (pdev->dev.of_node) { |
| const struct of_device_id *match; |
| match = of_match_node(atmel_dma_dt_ids, pdev->dev.of_node); |
| if (match == NULL) |
| return NULL; |
| return match->data; |
| } |
| return (struct at_dma_platform_data *) |
| platform_get_device_id(pdev)->driver_data; |
| } |
| |
| /** |
| * at_dma_off - disable DMA controller |
| * @atdma: the Atmel HDAMC device |
| */ |
| static void at_dma_off(struct at_dma *atdma) |
| { |
| dma_writel(atdma, EN, 0); |
| |
| /* disable all interrupts */ |
| dma_writel(atdma, EBCIDR, -1L); |
| |
| /* confirm that all channels are disabled */ |
| while (dma_readl(atdma, CHSR) & atdma->all_chan_mask) |
| cpu_relax(); |
| } |
| |
| static int __init at_dma_probe(struct platform_device *pdev) |
| { |
| struct at_dma *atdma; |
| int irq; |
| int err; |
| int i; |
| const struct at_dma_platform_data *plat_dat; |
| |
| /* setup platform data for each SoC */ |
| dma_cap_set(DMA_MEMCPY, at91sam9rl_config.cap_mask); |
| dma_cap_set(DMA_INTERLEAVE, at91sam9g45_config.cap_mask); |
| dma_cap_set(DMA_MEMCPY, at91sam9g45_config.cap_mask); |
| dma_cap_set(DMA_MEMSET, at91sam9g45_config.cap_mask); |
| dma_cap_set(DMA_MEMSET_SG, at91sam9g45_config.cap_mask); |
| dma_cap_set(DMA_PRIVATE, at91sam9g45_config.cap_mask); |
| dma_cap_set(DMA_SLAVE, at91sam9g45_config.cap_mask); |
| |
| /* get DMA parameters from controller type */ |
| plat_dat = at_dma_get_driver_data(pdev); |
| if (!plat_dat) |
| return -ENODEV; |
| |
| atdma = devm_kzalloc(&pdev->dev, |
| struct_size(atdma, chan, plat_dat->nr_channels), |
| GFP_KERNEL); |
| if (!atdma) |
| return -ENOMEM; |
| |
| atdma->regs = devm_platform_ioremap_resource(pdev, 0); |
| if (IS_ERR(atdma->regs)) |
| return PTR_ERR(atdma->regs); |
| |
| irq = platform_get_irq(pdev, 0); |
| if (irq < 0) |
| return irq; |
| |
| /* discover transaction capabilities */ |
| atdma->dma_device.cap_mask = plat_dat->cap_mask; |
| atdma->all_chan_mask = (1 << plat_dat->nr_channels) - 1; |
| |
| atdma->clk = devm_clk_get(&pdev->dev, "dma_clk"); |
| if (IS_ERR(atdma->clk)) |
| return PTR_ERR(atdma->clk); |
| |
| err = clk_prepare_enable(atdma->clk); |
| if (err) |
| return err; |
| |
| /* force dma off, just in case */ |
| at_dma_off(atdma); |
| |
| err = request_irq(irq, at_dma_interrupt, 0, "at_hdmac", atdma); |
| if (err) |
| goto err_irq; |
| |
| platform_set_drvdata(pdev, atdma); |
| |
| /* create a pool of consistent memory blocks for hardware descriptors */ |
| atdma->lli_pool = dma_pool_create("at_hdmac_lli_pool", |
| &pdev->dev, sizeof(struct at_lli), |
| 4 /* word alignment */, 0); |
| if (!atdma->lli_pool) { |
| dev_err(&pdev->dev, "Unable to allocate DMA LLI descriptor pool\n"); |
| err = -ENOMEM; |
| goto err_desc_pool_create; |
| } |
| |
| /* create a pool of consistent memory blocks for memset blocks */ |
| atdma->memset_pool = dma_pool_create("at_hdmac_memset_pool", |
| &pdev->dev, sizeof(int), 4, 0); |
| if (!atdma->memset_pool) { |
| dev_err(&pdev->dev, "No memory for memset dma pool\n"); |
| err = -ENOMEM; |
| goto err_memset_pool_create; |
| } |
| |
| /* clear any pending interrupt */ |
| while (dma_readl(atdma, EBCISR)) |
| cpu_relax(); |
| |
| /* initialize channels related values */ |
| INIT_LIST_HEAD(&atdma->dma_device.channels); |
| for (i = 0; i < plat_dat->nr_channels; i++) { |
| struct at_dma_chan *atchan = &atdma->chan[i]; |
| |
| atchan->mem_if = AT_DMA_MEM_IF; |
| atchan->per_if = AT_DMA_PER_IF; |
| |
| atchan->ch_regs = atdma->regs + ch_regs(i); |
| atchan->mask = 1 << i; |
| |
| atchan->atdma = atdma; |
| atchan->vc.desc_free = atdma_desc_free; |
| vchan_init(&atchan->vc, &atdma->dma_device); |
| atc_enable_chan_irq(atdma, i); |
| } |
| |
| /* set base routines */ |
| atdma->dma_device.device_alloc_chan_resources = atc_alloc_chan_resources; |
| atdma->dma_device.device_free_chan_resources = atc_free_chan_resources; |
| atdma->dma_device.device_tx_status = atc_tx_status; |
| atdma->dma_device.device_issue_pending = atc_issue_pending; |
| atdma->dma_device.dev = &pdev->dev; |
| |
| /* set prep routines based on capability */ |
| if (dma_has_cap(DMA_INTERLEAVE, atdma->dma_device.cap_mask)) |
| atdma->dma_device.device_prep_interleaved_dma = atc_prep_dma_interleaved; |
| |
| if (dma_has_cap(DMA_MEMCPY, atdma->dma_device.cap_mask)) |
| atdma->dma_device.device_prep_dma_memcpy = atc_prep_dma_memcpy; |
| |
| if (dma_has_cap(DMA_MEMSET, atdma->dma_device.cap_mask)) { |
| atdma->dma_device.device_prep_dma_memset = atc_prep_dma_memset; |
| atdma->dma_device.device_prep_dma_memset_sg = atc_prep_dma_memset_sg; |
| atdma->dma_device.fill_align = DMAENGINE_ALIGN_4_BYTES; |
| } |
| |
| if (dma_has_cap(DMA_SLAVE, atdma->dma_device.cap_mask)) { |
| atdma->dma_device.device_prep_slave_sg = atc_prep_slave_sg; |
| /* controller can do slave DMA: can trigger cyclic transfers */ |
| dma_cap_set(DMA_CYCLIC, atdma->dma_device.cap_mask); |
| atdma->dma_device.device_prep_dma_cyclic = atc_prep_dma_cyclic; |
| atdma->dma_device.device_config = atc_config; |
| atdma->dma_device.device_pause = atc_pause; |
| atdma->dma_device.device_resume = atc_resume; |
| atdma->dma_device.device_terminate_all = atc_terminate_all; |
| atdma->dma_device.src_addr_widths = ATC_DMA_BUSWIDTHS; |
| atdma->dma_device.dst_addr_widths = ATC_DMA_BUSWIDTHS; |
| atdma->dma_device.directions = BIT(DMA_DEV_TO_MEM) | BIT(DMA_MEM_TO_DEV); |
| atdma->dma_device.residue_granularity = DMA_RESIDUE_GRANULARITY_BURST; |
| } |
| |
| dma_writel(atdma, EN, AT_DMA_ENABLE); |
| |
| dev_info(&pdev->dev, "Atmel AHB DMA Controller ( %s%s%s), %d channels\n", |
| dma_has_cap(DMA_MEMCPY, atdma->dma_device.cap_mask) ? "cpy " : "", |
| dma_has_cap(DMA_MEMSET, atdma->dma_device.cap_mask) ? "set " : "", |
| dma_has_cap(DMA_SLAVE, atdma->dma_device.cap_mask) ? "slave " : "", |
| plat_dat->nr_channels); |
| |
| err = dma_async_device_register(&atdma->dma_device); |
| if (err) { |
| dev_err(&pdev->dev, "Unable to register: %d.\n", err); |
| goto err_dma_async_device_register; |
| } |
| |
| /* |
| * Do not return an error if the dmac node is not present in order to |
| * not break the existing way of requesting channel with |
| * dma_request_channel(). |
| */ |
| if (pdev->dev.of_node) { |
| err = of_dma_controller_register(pdev->dev.of_node, |
| at_dma_xlate, atdma); |
| if (err) { |
| dev_err(&pdev->dev, "could not register of_dma_controller\n"); |
| goto err_of_dma_controller_register; |
| } |
| } |
| |
| return 0; |
| |
| err_of_dma_controller_register: |
| dma_async_device_unregister(&atdma->dma_device); |
| err_dma_async_device_register: |
| dma_pool_destroy(atdma->memset_pool); |
| err_memset_pool_create: |
| dma_pool_destroy(atdma->lli_pool); |
| err_desc_pool_create: |
| free_irq(platform_get_irq(pdev, 0), atdma); |
| err_irq: |
| clk_disable_unprepare(atdma->clk); |
| return err; |
| } |
| |
| static void at_dma_remove(struct platform_device *pdev) |
| { |
| struct at_dma *atdma = platform_get_drvdata(pdev); |
| struct dma_chan *chan, *_chan; |
| |
| at_dma_off(atdma); |
| if (pdev->dev.of_node) |
| of_dma_controller_free(pdev->dev.of_node); |
| dma_async_device_unregister(&atdma->dma_device); |
| |
| dma_pool_destroy(atdma->memset_pool); |
| dma_pool_destroy(atdma->lli_pool); |
| free_irq(platform_get_irq(pdev, 0), atdma); |
| |
| list_for_each_entry_safe(chan, _chan, &atdma->dma_device.channels, |
| device_node) { |
| /* Disable interrupts */ |
| atc_disable_chan_irq(atdma, chan->chan_id); |
| list_del(&chan->device_node); |
| } |
| |
| clk_disable_unprepare(atdma->clk); |
| } |
| |
| static void at_dma_shutdown(struct platform_device *pdev) |
| { |
| struct at_dma *atdma = platform_get_drvdata(pdev); |
| |
| at_dma_off(platform_get_drvdata(pdev)); |
| clk_disable_unprepare(atdma->clk); |
| } |
| |
| static int at_dma_prepare(struct device *dev) |
| { |
| struct at_dma *atdma = dev_get_drvdata(dev); |
| struct dma_chan *chan, *_chan; |
| |
| list_for_each_entry_safe(chan, _chan, &atdma->dma_device.channels, |
| device_node) { |
| struct at_dma_chan *atchan = to_at_dma_chan(chan); |
| /* wait for transaction completion (except in cyclic case) */ |
| if (atc_chan_is_enabled(atchan) && !atc_chan_is_cyclic(atchan)) |
| return -EAGAIN; |
| } |
| return 0; |
| } |
| |
| static void atc_suspend_cyclic(struct at_dma_chan *atchan) |
| { |
| struct dma_chan *chan = &atchan->vc.chan; |
| |
| /* Channel should be paused by user |
| * do it anyway even if it is not done already */ |
| if (!atc_chan_is_paused(atchan)) { |
| dev_warn(chan2dev(chan), |
| "cyclic channel not paused, should be done by channel user\n"); |
| atc_pause(chan); |
| } |
| |
| /* now preserve additional data for cyclic operations */ |
| /* next descriptor address in the cyclic list */ |
| atchan->save_dscr = channel_readl(atchan, DSCR); |
| |
| vdbg_dump_regs(atchan); |
| } |
| |
| static int at_dma_suspend_noirq(struct device *dev) |
| { |
| struct at_dma *atdma = dev_get_drvdata(dev); |
| struct dma_chan *chan, *_chan; |
| |
| /* preserve data */ |
| list_for_each_entry_safe(chan, _chan, &atdma->dma_device.channels, |
| device_node) { |
| struct at_dma_chan *atchan = to_at_dma_chan(chan); |
| |
| if (atc_chan_is_cyclic(atchan)) |
| atc_suspend_cyclic(atchan); |
| atchan->save_cfg = channel_readl(atchan, CFG); |
| } |
| atdma->save_imr = dma_readl(atdma, EBCIMR); |
| |
| /* disable DMA controller */ |
| at_dma_off(atdma); |
| clk_disable_unprepare(atdma->clk); |
| return 0; |
| } |
| |
| static void atc_resume_cyclic(struct at_dma_chan *atchan) |
| { |
| struct at_dma *atdma = to_at_dma(atchan->vc.chan.device); |
| |
| /* restore channel status for cyclic descriptors list: |
| * next descriptor in the cyclic list at the time of suspend */ |
| channel_writel(atchan, SADDR, 0); |
| channel_writel(atchan, DADDR, 0); |
| channel_writel(atchan, CTRLA, 0); |
| channel_writel(atchan, CTRLB, 0); |
| channel_writel(atchan, DSCR, atchan->save_dscr); |
| dma_writel(atdma, CHER, atchan->mask); |
| |
| /* channel pause status should be removed by channel user |
| * We cannot take the initiative to do it here */ |
| |
| vdbg_dump_regs(atchan); |
| } |
| |
| static int at_dma_resume_noirq(struct device *dev) |
| { |
| struct at_dma *atdma = dev_get_drvdata(dev); |
| struct dma_chan *chan, *_chan; |
| |
| /* bring back DMA controller */ |
| clk_prepare_enable(atdma->clk); |
| dma_writel(atdma, EN, AT_DMA_ENABLE); |
| |
| /* clear any pending interrupt */ |
| while (dma_readl(atdma, EBCISR)) |
| cpu_relax(); |
| |
| /* restore saved data */ |
| dma_writel(atdma, EBCIER, atdma->save_imr); |
| list_for_each_entry_safe(chan, _chan, &atdma->dma_device.channels, |
| device_node) { |
| struct at_dma_chan *atchan = to_at_dma_chan(chan); |
| |
| channel_writel(atchan, CFG, atchan->save_cfg); |
| if (atc_chan_is_cyclic(atchan)) |
| atc_resume_cyclic(atchan); |
| } |
| return 0; |
| } |
| |
| static const struct dev_pm_ops __maybe_unused at_dma_dev_pm_ops = { |
| .prepare = at_dma_prepare, |
| .suspend_noirq = at_dma_suspend_noirq, |
| .resume_noirq = at_dma_resume_noirq, |
| }; |
| |
| static struct platform_driver at_dma_driver = { |
| .remove_new = at_dma_remove, |
| .shutdown = at_dma_shutdown, |
| .id_table = atdma_devtypes, |
| .driver = { |
| .name = "at_hdmac", |
| .pm = pm_ptr(&at_dma_dev_pm_ops), |
| .of_match_table = of_match_ptr(atmel_dma_dt_ids), |
| }, |
| }; |
| |
| static int __init at_dma_init(void) |
| { |
| return platform_driver_probe(&at_dma_driver, at_dma_probe); |
| } |
| subsys_initcall(at_dma_init); |
| |
| static void __exit at_dma_exit(void) |
| { |
| platform_driver_unregister(&at_dma_driver); |
| } |
| module_exit(at_dma_exit); |
| |
| MODULE_DESCRIPTION("Atmel AHB DMA Controller driver"); |
| MODULE_AUTHOR("Nicolas Ferre <nicolas.ferre@atmel.com>"); |
| MODULE_AUTHOR("Tudor Ambarus <tudor.ambarus@microchip.com>"); |
| MODULE_LICENSE("GPL"); |
| MODULE_ALIAS("platform:at_hdmac"); |