| // SPDX-License-Identifier: GPL-2.0-only |
| /* |
| * Copyright (c) 2016, The Linux Foundation. All rights reserved. |
| */ |
| |
| #include <linux/clk.h> |
| #include <linux/clk-provider.h> |
| #include <linux/delay.h> |
| |
| #include "dsi_phy.h" |
| #include "dsi.xml.h" |
| #include "dsi_phy_14nm.xml.h" |
| |
| #define PHY_14NM_CKLN_IDX 4 |
| |
| /* |
| * DSI PLL 14nm - clock diagram (eg: DSI0): |
| * |
| * dsi0n1_postdiv_clk |
| * | |
| * | |
| * +----+ | +----+ |
| * dsi0vco_clk ---| n1 |--o--| /8 |-- dsi0pllbyte |
| * +----+ | +----+ |
| * | dsi0n1_postdivby2_clk |
| * | +----+ | |
| * o---| /2 |--o--|\ |
| * | +----+ | \ +----+ |
| * | | |--| n2 |-- dsi0pll |
| * o--------------| / +----+ |
| * |/ |
| */ |
| |
| #define POLL_MAX_READS 15 |
| #define POLL_TIMEOUT_US 1000 |
| |
| #define VCO_REF_CLK_RATE 19200000 |
| #define VCO_MIN_RATE 1300000000UL |
| #define VCO_MAX_RATE 2600000000UL |
| |
| struct dsi_pll_config { |
| u64 vco_current_rate; |
| |
| u32 ssc_en; /* SSC enable/disable */ |
| |
| /* fixed params */ |
| u32 plllock_cnt; |
| u32 ssc_center; |
| u32 ssc_adj_period; |
| u32 ssc_spread; |
| u32 ssc_freq; |
| |
| /* calculated */ |
| u32 dec_start; |
| u32 div_frac_start; |
| u32 ssc_period; |
| u32 ssc_step_size; |
| u32 plllock_cmp; |
| u32 pll_vco_div_ref; |
| u32 pll_vco_count; |
| u32 pll_kvco_div_ref; |
| u32 pll_kvco_count; |
| }; |
| |
| struct pll_14nm_cached_state { |
| unsigned long vco_rate; |
| u8 n2postdiv; |
| u8 n1postdiv; |
| }; |
| |
| struct dsi_pll_14nm { |
| struct clk_hw clk_hw; |
| |
| struct msm_dsi_phy *phy; |
| |
| /* protects REG_DSI_14nm_PHY_CMN_CLK_CFG0 register */ |
| spinlock_t postdiv_lock; |
| |
| struct pll_14nm_cached_state cached_state; |
| |
| struct dsi_pll_14nm *slave; |
| }; |
| |
| #define to_pll_14nm(x) container_of(x, struct dsi_pll_14nm, clk_hw) |
| |
| /* |
| * Private struct for N1/N2 post-divider clocks. These clocks are similar to |
| * the generic clk_divider class of clocks. The only difference is that it |
| * also sets the slave DSI PLL's post-dividers if in bonded DSI mode |
| */ |
| struct dsi_pll_14nm_postdiv { |
| struct clk_hw hw; |
| |
| /* divider params */ |
| u8 shift; |
| u8 width; |
| u8 flags; /* same flags as used by clk_divider struct */ |
| |
| struct dsi_pll_14nm *pll; |
| }; |
| |
| #define to_pll_14nm_postdiv(_hw) container_of(_hw, struct dsi_pll_14nm_postdiv, hw) |
| |
| /* |
| * Global list of private DSI PLL struct pointers. We need this for bonded DSI |
| * mode, where the master PLL's clk_ops needs access the slave's private data |
| */ |
| static struct dsi_pll_14nm *pll_14nm_list[DSI_MAX]; |
| |
| static bool pll_14nm_poll_for_ready(struct dsi_pll_14nm *pll_14nm, |
| u32 nb_tries, u32 timeout_us) |
| { |
| bool pll_locked = false, pll_ready = false; |
| void __iomem *base = pll_14nm->phy->pll_base; |
| u32 tries, val; |
| |
| tries = nb_tries; |
| while (tries--) { |
| val = readl(base + REG_DSI_14nm_PHY_PLL_RESET_SM_READY_STATUS); |
| pll_locked = !!(val & BIT(5)); |
| |
| if (pll_locked) |
| break; |
| |
| udelay(timeout_us); |
| } |
| |
| if (!pll_locked) |
| goto out; |
| |
| tries = nb_tries; |
| while (tries--) { |
| val = readl(base + REG_DSI_14nm_PHY_PLL_RESET_SM_READY_STATUS); |
| pll_ready = !!(val & BIT(0)); |
| |
| if (pll_ready) |
| break; |
| |
| udelay(timeout_us); |
| } |
| |
| out: |
| DBG("DSI PLL is %slocked, %sready", pll_locked ? "" : "*not* ", pll_ready ? "" : "*not* "); |
| |
| return pll_locked && pll_ready; |
| } |
| |
| static void dsi_pll_14nm_config_init(struct dsi_pll_config *pconf) |
| { |
| /* fixed input */ |
| pconf->plllock_cnt = 1; |
| |
| /* |
| * SSC is enabled by default. We might need DT props for configuring |
| * some SSC params like PPM and center/down spread etc. |
| */ |
| pconf->ssc_en = 1; |
| pconf->ssc_center = 0; /* down spread by default */ |
| pconf->ssc_spread = 5; /* PPM / 1000 */ |
| pconf->ssc_freq = 31500; /* default recommended */ |
| pconf->ssc_adj_period = 37; |
| } |
| |
| #define CEIL(x, y) (((x) + ((y) - 1)) / (y)) |
| |
| static void pll_14nm_ssc_calc(struct dsi_pll_14nm *pll, struct dsi_pll_config *pconf) |
| { |
| u32 period, ssc_period; |
| u32 ref, rem; |
| u64 step_size; |
| |
| DBG("vco=%lld ref=%d", pconf->vco_current_rate, VCO_REF_CLK_RATE); |
| |
| ssc_period = pconf->ssc_freq / 500; |
| period = (u32)VCO_REF_CLK_RATE / 1000; |
| ssc_period = CEIL(period, ssc_period); |
| ssc_period -= 1; |
| pconf->ssc_period = ssc_period; |
| |
| DBG("ssc freq=%d spread=%d period=%d", pconf->ssc_freq, |
| pconf->ssc_spread, pconf->ssc_period); |
| |
| step_size = (u32)pconf->vco_current_rate; |
| ref = VCO_REF_CLK_RATE; |
| ref /= 1000; |
| step_size = div_u64(step_size, ref); |
| step_size <<= 20; |
| step_size = div_u64(step_size, 1000); |
| step_size *= pconf->ssc_spread; |
| step_size = div_u64(step_size, 1000); |
| step_size *= (pconf->ssc_adj_period + 1); |
| |
| rem = 0; |
| step_size = div_u64_rem(step_size, ssc_period + 1, &rem); |
| if (rem) |
| step_size++; |
| |
| DBG("step_size=%lld", step_size); |
| |
| step_size &= 0x0ffff; /* take lower 16 bits */ |
| |
| pconf->ssc_step_size = step_size; |
| } |
| |
| static void pll_14nm_dec_frac_calc(struct dsi_pll_14nm *pll, struct dsi_pll_config *pconf) |
| { |
| u64 multiplier = BIT(20); |
| u64 dec_start_multiple, dec_start, pll_comp_val; |
| u32 duration, div_frac_start; |
| u64 vco_clk_rate = pconf->vco_current_rate; |
| u64 fref = VCO_REF_CLK_RATE; |
| |
| DBG("vco_clk_rate=%lld ref_clk_rate=%lld", vco_clk_rate, fref); |
| |
| dec_start_multiple = div_u64(vco_clk_rate * multiplier, fref); |
| dec_start = div_u64_rem(dec_start_multiple, multiplier, &div_frac_start); |
| |
| pconf->dec_start = (u32)dec_start; |
| pconf->div_frac_start = div_frac_start; |
| |
| if (pconf->plllock_cnt == 0) |
| duration = 1024; |
| else if (pconf->plllock_cnt == 1) |
| duration = 256; |
| else if (pconf->plllock_cnt == 2) |
| duration = 128; |
| else |
| duration = 32; |
| |
| pll_comp_val = duration * dec_start_multiple; |
| pll_comp_val = div_u64(pll_comp_val, multiplier); |
| do_div(pll_comp_val, 10); |
| |
| pconf->plllock_cmp = (u32)pll_comp_val; |
| } |
| |
| static u32 pll_14nm_kvco_slop(u32 vrate) |
| { |
| u32 slop = 0; |
| |
| if (vrate > VCO_MIN_RATE && vrate <= 1800000000UL) |
| slop = 600; |
| else if (vrate > 1800000000UL && vrate < 2300000000UL) |
| slop = 400; |
| else if (vrate > 2300000000UL && vrate < VCO_MAX_RATE) |
| slop = 280; |
| |
| return slop; |
| } |
| |
| static void pll_14nm_calc_vco_count(struct dsi_pll_14nm *pll, struct dsi_pll_config *pconf) |
| { |
| u64 vco_clk_rate = pconf->vco_current_rate; |
| u64 fref = VCO_REF_CLK_RATE; |
| u32 vco_measure_time = 5; |
| u32 kvco_measure_time = 5; |
| u64 data; |
| u32 cnt; |
| |
| data = fref * vco_measure_time; |
| do_div(data, 1000000); |
| data &= 0x03ff; /* 10 bits */ |
| data -= 2; |
| pconf->pll_vco_div_ref = data; |
| |
| data = div_u64(vco_clk_rate, 1000000); /* unit is Mhz */ |
| data *= vco_measure_time; |
| do_div(data, 10); |
| pconf->pll_vco_count = data; |
| |
| data = fref * kvco_measure_time; |
| do_div(data, 1000000); |
| data &= 0x03ff; /* 10 bits */ |
| data -= 1; |
| pconf->pll_kvco_div_ref = data; |
| |
| cnt = pll_14nm_kvco_slop(vco_clk_rate); |
| cnt *= 2; |
| cnt /= 100; |
| cnt *= kvco_measure_time; |
| pconf->pll_kvco_count = cnt; |
| } |
| |
| static void pll_db_commit_ssc(struct dsi_pll_14nm *pll, struct dsi_pll_config *pconf) |
| { |
| void __iomem *base = pll->phy->pll_base; |
| u8 data; |
| |
| data = pconf->ssc_adj_period; |
| data &= 0x0ff; |
| writel(data, base + REG_DSI_14nm_PHY_PLL_SSC_ADJ_PER1); |
| data = (pconf->ssc_adj_period >> 8); |
| data &= 0x03; |
| writel(data, base + REG_DSI_14nm_PHY_PLL_SSC_ADJ_PER2); |
| |
| data = pconf->ssc_period; |
| data &= 0x0ff; |
| writel(data, base + REG_DSI_14nm_PHY_PLL_SSC_PER1); |
| data = (pconf->ssc_period >> 8); |
| data &= 0x0ff; |
| writel(data, base + REG_DSI_14nm_PHY_PLL_SSC_PER2); |
| |
| data = pconf->ssc_step_size; |
| data &= 0x0ff; |
| writel(data, base + REG_DSI_14nm_PHY_PLL_SSC_STEP_SIZE1); |
| data = (pconf->ssc_step_size >> 8); |
| data &= 0x0ff; |
| writel(data, base + REG_DSI_14nm_PHY_PLL_SSC_STEP_SIZE2); |
| |
| data = (pconf->ssc_center & 0x01); |
| data <<= 1; |
| data |= 0x01; /* enable */ |
| writel(data, base + REG_DSI_14nm_PHY_PLL_SSC_EN_CENTER); |
| |
| wmb(); /* make sure register committed */ |
| } |
| |
| static void pll_db_commit_common(struct dsi_pll_14nm *pll, |
| struct dsi_pll_config *pconf) |
| { |
| void __iomem *base = pll->phy->pll_base; |
| u8 data; |
| |
| /* confgiure the non frequency dependent pll registers */ |
| data = 0; |
| writel(data, base + REG_DSI_14nm_PHY_PLL_SYSCLK_EN_RESET); |
| |
| writel(1, base + REG_DSI_14nm_PHY_PLL_TXCLK_EN); |
| |
| writel(48, base + REG_DSI_14nm_PHY_PLL_RESETSM_CNTRL); |
| /* bandgap_timer */ |
| writel(4 << 3, base + REG_DSI_14nm_PHY_PLL_RESETSM_CNTRL2); |
| /* pll_wakeup_timer */ |
| writel(5, base + REG_DSI_14nm_PHY_PLL_RESETSM_CNTRL5); |
| |
| data = pconf->pll_vco_div_ref & 0xff; |
| writel(data, base + REG_DSI_14nm_PHY_PLL_VCO_DIV_REF1); |
| data = (pconf->pll_vco_div_ref >> 8) & 0x3; |
| writel(data, base + REG_DSI_14nm_PHY_PLL_VCO_DIV_REF2); |
| |
| data = pconf->pll_kvco_div_ref & 0xff; |
| writel(data, base + REG_DSI_14nm_PHY_PLL_KVCO_DIV_REF1); |
| data = (pconf->pll_kvco_div_ref >> 8) & 0x3; |
| writel(data, base + REG_DSI_14nm_PHY_PLL_KVCO_DIV_REF2); |
| |
| writel(16, base + REG_DSI_14nm_PHY_PLL_PLL_MISC1); |
| |
| writel(4, base + REG_DSI_14nm_PHY_PLL_IE_TRIM); |
| |
| writel(4, base + REG_DSI_14nm_PHY_PLL_IP_TRIM); |
| |
| writel(1 << 3 | 1, base + REG_DSI_14nm_PHY_PLL_CP_SET_CUR); |
| |
| writel(0 << 3 | 0, base + REG_DSI_14nm_PHY_PLL_PLL_ICPCSET); |
| |
| writel(0 << 3 | 0, base + REG_DSI_14nm_PHY_PLL_PLL_ICPMSET); |
| |
| writel(4 << 3 | 4, base + REG_DSI_14nm_PHY_PLL_PLL_ICP_SET); |
| |
| writel(1 << 4 | 11, base + REG_DSI_14nm_PHY_PLL_PLL_LPF1); |
| |
| writel(7, base + REG_DSI_14nm_PHY_PLL_IPTAT_TRIM); |
| |
| writel(1 << 4 | 2, base + REG_DSI_14nm_PHY_PLL_PLL_CRCTRL); |
| } |
| |
| static void pll_14nm_software_reset(struct dsi_pll_14nm *pll_14nm) |
| { |
| void __iomem *cmn_base = pll_14nm->phy->base; |
| |
| /* de assert pll start and apply pll sw reset */ |
| |
| /* stop pll */ |
| writel(0, cmn_base + REG_DSI_14nm_PHY_CMN_PLL_CNTRL); |
| |
| /* pll sw reset */ |
| writel(0x20, cmn_base + REG_DSI_14nm_PHY_CMN_CTRL_1); |
| udelay(10); |
| wmb(); /* make sure register committed */ |
| |
| writel(0, cmn_base + REG_DSI_14nm_PHY_CMN_CTRL_1); |
| wmb(); /* make sure register committed */ |
| } |
| |
| static void pll_db_commit_14nm(struct dsi_pll_14nm *pll, |
| struct dsi_pll_config *pconf) |
| { |
| void __iomem *base = pll->phy->pll_base; |
| void __iomem *cmn_base = pll->phy->base; |
| u8 data; |
| |
| DBG("DSI%d PLL", pll->phy->id); |
| |
| writel(0x3c, cmn_base + REG_DSI_14nm_PHY_CMN_LDO_CNTRL); |
| |
| pll_db_commit_common(pll, pconf); |
| |
| pll_14nm_software_reset(pll); |
| |
| /* Use the /2 path in Mux */ |
| writel(1, cmn_base + REG_DSI_14nm_PHY_CMN_CLK_CFG1); |
| |
| data = 0xff; /* data, clk, pll normal operation */ |
| writel(data, cmn_base + REG_DSI_14nm_PHY_CMN_CTRL_0); |
| |
| /* configure the frequency dependent pll registers */ |
| data = pconf->dec_start; |
| writel(data, base + REG_DSI_14nm_PHY_PLL_DEC_START); |
| |
| data = pconf->div_frac_start & 0xff; |
| writel(data, base + REG_DSI_14nm_PHY_PLL_DIV_FRAC_START1); |
| data = (pconf->div_frac_start >> 8) & 0xff; |
| writel(data, base + REG_DSI_14nm_PHY_PLL_DIV_FRAC_START2); |
| data = (pconf->div_frac_start >> 16) & 0xf; |
| writel(data, base + REG_DSI_14nm_PHY_PLL_DIV_FRAC_START3); |
| |
| data = pconf->plllock_cmp & 0xff; |
| writel(data, base + REG_DSI_14nm_PHY_PLL_PLLLOCK_CMP1); |
| |
| data = (pconf->plllock_cmp >> 8) & 0xff; |
| writel(data, base + REG_DSI_14nm_PHY_PLL_PLLLOCK_CMP2); |
| |
| data = (pconf->plllock_cmp >> 16) & 0x3; |
| writel(data, base + REG_DSI_14nm_PHY_PLL_PLLLOCK_CMP3); |
| |
| data = pconf->plllock_cnt << 1 | 0 << 3; /* plllock_rng */ |
| writel(data, base + REG_DSI_14nm_PHY_PLL_PLLLOCK_CMP_EN); |
| |
| data = pconf->pll_vco_count & 0xff; |
| writel(data, base + REG_DSI_14nm_PHY_PLL_VCO_COUNT1); |
| data = (pconf->pll_vco_count >> 8) & 0xff; |
| writel(data, base + REG_DSI_14nm_PHY_PLL_VCO_COUNT2); |
| |
| data = pconf->pll_kvco_count & 0xff; |
| writel(data, base + REG_DSI_14nm_PHY_PLL_KVCO_COUNT1); |
| data = (pconf->pll_kvco_count >> 8) & 0x3; |
| writel(data, base + REG_DSI_14nm_PHY_PLL_KVCO_COUNT2); |
| |
| /* |
| * High nibble configures the post divider internal to the VCO. It's |
| * fixed to divide by 1 for now. |
| * |
| * 0: divided by 1 |
| * 1: divided by 2 |
| * 2: divided by 4 |
| * 3: divided by 8 |
| */ |
| writel(0 << 4 | 3, base + REG_DSI_14nm_PHY_PLL_PLL_LPF2_POSTDIV); |
| |
| if (pconf->ssc_en) |
| pll_db_commit_ssc(pll, pconf); |
| |
| wmb(); /* make sure register committed */ |
| } |
| |
| /* |
| * VCO clock Callbacks |
| */ |
| static int dsi_pll_14nm_vco_set_rate(struct clk_hw *hw, unsigned long rate, |
| unsigned long parent_rate) |
| { |
| struct dsi_pll_14nm *pll_14nm = to_pll_14nm(hw); |
| struct dsi_pll_config conf; |
| |
| DBG("DSI PLL%d rate=%lu, parent's=%lu", pll_14nm->phy->id, rate, |
| parent_rate); |
| |
| dsi_pll_14nm_config_init(&conf); |
| conf.vco_current_rate = rate; |
| |
| pll_14nm_dec_frac_calc(pll_14nm, &conf); |
| |
| if (conf.ssc_en) |
| pll_14nm_ssc_calc(pll_14nm, &conf); |
| |
| pll_14nm_calc_vco_count(pll_14nm, &conf); |
| |
| /* commit the slave DSI PLL registers if we're master. Note that we |
| * don't lock the slave PLL. We just ensure that the PLL/PHY registers |
| * of the master and slave are identical |
| */ |
| if (pll_14nm->phy->usecase == MSM_DSI_PHY_MASTER) { |
| struct dsi_pll_14nm *pll_14nm_slave = pll_14nm->slave; |
| |
| pll_db_commit_14nm(pll_14nm_slave, &conf); |
| } |
| |
| pll_db_commit_14nm(pll_14nm, &conf); |
| |
| return 0; |
| } |
| |
| static unsigned long dsi_pll_14nm_vco_recalc_rate(struct clk_hw *hw, |
| unsigned long parent_rate) |
| { |
| struct dsi_pll_14nm *pll_14nm = to_pll_14nm(hw); |
| void __iomem *base = pll_14nm->phy->pll_base; |
| u64 vco_rate, multiplier = BIT(20); |
| u32 div_frac_start; |
| u32 dec_start; |
| u64 ref_clk = parent_rate; |
| |
| dec_start = readl(base + REG_DSI_14nm_PHY_PLL_DEC_START); |
| dec_start &= 0x0ff; |
| |
| DBG("dec_start = %x", dec_start); |
| |
| div_frac_start = (readl(base + REG_DSI_14nm_PHY_PLL_DIV_FRAC_START3) |
| & 0xf) << 16; |
| div_frac_start |= (readl(base + REG_DSI_14nm_PHY_PLL_DIV_FRAC_START2) |
| & 0xff) << 8; |
| div_frac_start |= readl(base + REG_DSI_14nm_PHY_PLL_DIV_FRAC_START1) |
| & 0xff; |
| |
| DBG("div_frac_start = %x", div_frac_start); |
| |
| vco_rate = ref_clk * dec_start; |
| |
| vco_rate += ((ref_clk * div_frac_start) / multiplier); |
| |
| /* |
| * Recalculating the rate from dec_start and frac_start doesn't end up |
| * the rate we originally set. Convert the freq to KHz, round it up and |
| * convert it back to MHz. |
| */ |
| vco_rate = DIV_ROUND_UP_ULL(vco_rate, 1000) * 1000; |
| |
| DBG("returning vco rate = %lu", (unsigned long)vco_rate); |
| |
| return (unsigned long)vco_rate; |
| } |
| |
| static int dsi_pll_14nm_vco_prepare(struct clk_hw *hw) |
| { |
| struct dsi_pll_14nm *pll_14nm = to_pll_14nm(hw); |
| void __iomem *base = pll_14nm->phy->pll_base; |
| void __iomem *cmn_base = pll_14nm->phy->base; |
| bool locked; |
| |
| DBG(""); |
| |
| if (unlikely(pll_14nm->phy->pll_on)) |
| return 0; |
| |
| if (dsi_pll_14nm_vco_recalc_rate(hw, VCO_REF_CLK_RATE) == 0) |
| dsi_pll_14nm_vco_set_rate(hw, pll_14nm->phy->cfg->min_pll_rate, VCO_REF_CLK_RATE); |
| |
| writel(0x10, base + REG_DSI_14nm_PHY_PLL_VREF_CFG1); |
| writel(1, cmn_base + REG_DSI_14nm_PHY_CMN_PLL_CNTRL); |
| |
| locked = pll_14nm_poll_for_ready(pll_14nm, POLL_MAX_READS, |
| POLL_TIMEOUT_US); |
| |
| if (unlikely(!locked)) { |
| DRM_DEV_ERROR(&pll_14nm->phy->pdev->dev, "DSI PLL lock failed\n"); |
| return -EINVAL; |
| } |
| |
| DBG("DSI PLL lock success"); |
| pll_14nm->phy->pll_on = true; |
| |
| return 0; |
| } |
| |
| static void dsi_pll_14nm_vco_unprepare(struct clk_hw *hw) |
| { |
| struct dsi_pll_14nm *pll_14nm = to_pll_14nm(hw); |
| void __iomem *cmn_base = pll_14nm->phy->base; |
| |
| DBG(""); |
| |
| if (unlikely(!pll_14nm->phy->pll_on)) |
| return; |
| |
| writel(0, cmn_base + REG_DSI_14nm_PHY_CMN_PLL_CNTRL); |
| |
| pll_14nm->phy->pll_on = false; |
| } |
| |
| static long dsi_pll_14nm_clk_round_rate(struct clk_hw *hw, |
| unsigned long rate, unsigned long *parent_rate) |
| { |
| struct dsi_pll_14nm *pll_14nm = to_pll_14nm(hw); |
| |
| if (rate < pll_14nm->phy->cfg->min_pll_rate) |
| return pll_14nm->phy->cfg->min_pll_rate; |
| else if (rate > pll_14nm->phy->cfg->max_pll_rate) |
| return pll_14nm->phy->cfg->max_pll_rate; |
| else |
| return rate; |
| } |
| |
| static const struct clk_ops clk_ops_dsi_pll_14nm_vco = { |
| .round_rate = dsi_pll_14nm_clk_round_rate, |
| .set_rate = dsi_pll_14nm_vco_set_rate, |
| .recalc_rate = dsi_pll_14nm_vco_recalc_rate, |
| .prepare = dsi_pll_14nm_vco_prepare, |
| .unprepare = dsi_pll_14nm_vco_unprepare, |
| }; |
| |
| /* |
| * N1 and N2 post-divider clock callbacks |
| */ |
| #define div_mask(width) ((1 << (width)) - 1) |
| static unsigned long dsi_pll_14nm_postdiv_recalc_rate(struct clk_hw *hw, |
| unsigned long parent_rate) |
| { |
| struct dsi_pll_14nm_postdiv *postdiv = to_pll_14nm_postdiv(hw); |
| struct dsi_pll_14nm *pll_14nm = postdiv->pll; |
| void __iomem *base = pll_14nm->phy->base; |
| u8 shift = postdiv->shift; |
| u8 width = postdiv->width; |
| u32 val; |
| |
| DBG("DSI%d PLL parent rate=%lu", pll_14nm->phy->id, parent_rate); |
| |
| val = readl(base + REG_DSI_14nm_PHY_CMN_CLK_CFG0) >> shift; |
| val &= div_mask(width); |
| |
| return divider_recalc_rate(hw, parent_rate, val, NULL, |
| postdiv->flags, width); |
| } |
| |
| static long dsi_pll_14nm_postdiv_round_rate(struct clk_hw *hw, |
| unsigned long rate, |
| unsigned long *prate) |
| { |
| struct dsi_pll_14nm_postdiv *postdiv = to_pll_14nm_postdiv(hw); |
| struct dsi_pll_14nm *pll_14nm = postdiv->pll; |
| |
| DBG("DSI%d PLL parent rate=%lu", pll_14nm->phy->id, rate); |
| |
| return divider_round_rate(hw, rate, prate, NULL, |
| postdiv->width, |
| postdiv->flags); |
| } |
| |
| static int dsi_pll_14nm_postdiv_set_rate(struct clk_hw *hw, unsigned long rate, |
| unsigned long parent_rate) |
| { |
| struct dsi_pll_14nm_postdiv *postdiv = to_pll_14nm_postdiv(hw); |
| struct dsi_pll_14nm *pll_14nm = postdiv->pll; |
| void __iomem *base = pll_14nm->phy->base; |
| spinlock_t *lock = &pll_14nm->postdiv_lock; |
| u8 shift = postdiv->shift; |
| u8 width = postdiv->width; |
| unsigned int value; |
| unsigned long flags = 0; |
| u32 val; |
| |
| DBG("DSI%d PLL parent rate=%lu parent rate %lu", pll_14nm->phy->id, rate, |
| parent_rate); |
| |
| value = divider_get_val(rate, parent_rate, NULL, postdiv->width, |
| postdiv->flags); |
| |
| spin_lock_irqsave(lock, flags); |
| |
| val = readl(base + REG_DSI_14nm_PHY_CMN_CLK_CFG0); |
| val &= ~(div_mask(width) << shift); |
| |
| val |= value << shift; |
| writel(val, base + REG_DSI_14nm_PHY_CMN_CLK_CFG0); |
| |
| /* If we're master in bonded DSI mode, then the slave PLL's post-dividers |
| * follow the master's post dividers |
| */ |
| if (pll_14nm->phy->usecase == MSM_DSI_PHY_MASTER) { |
| struct dsi_pll_14nm *pll_14nm_slave = pll_14nm->slave; |
| void __iomem *slave_base = pll_14nm_slave->phy->base; |
| |
| writel(val, slave_base + REG_DSI_14nm_PHY_CMN_CLK_CFG0); |
| } |
| |
| spin_unlock_irqrestore(lock, flags); |
| |
| return 0; |
| } |
| |
| static const struct clk_ops clk_ops_dsi_pll_14nm_postdiv = { |
| .recalc_rate = dsi_pll_14nm_postdiv_recalc_rate, |
| .round_rate = dsi_pll_14nm_postdiv_round_rate, |
| .set_rate = dsi_pll_14nm_postdiv_set_rate, |
| }; |
| |
| /* |
| * PLL Callbacks |
| */ |
| |
| static void dsi_14nm_pll_save_state(struct msm_dsi_phy *phy) |
| { |
| struct dsi_pll_14nm *pll_14nm = to_pll_14nm(phy->vco_hw); |
| struct pll_14nm_cached_state *cached_state = &pll_14nm->cached_state; |
| void __iomem *cmn_base = pll_14nm->phy->base; |
| u32 data; |
| |
| data = readl(cmn_base + REG_DSI_14nm_PHY_CMN_CLK_CFG0); |
| |
| cached_state->n1postdiv = data & 0xf; |
| cached_state->n2postdiv = (data >> 4) & 0xf; |
| |
| DBG("DSI%d PLL save state %x %x", pll_14nm->phy->id, |
| cached_state->n1postdiv, cached_state->n2postdiv); |
| |
| cached_state->vco_rate = clk_hw_get_rate(phy->vco_hw); |
| } |
| |
| static int dsi_14nm_pll_restore_state(struct msm_dsi_phy *phy) |
| { |
| struct dsi_pll_14nm *pll_14nm = to_pll_14nm(phy->vco_hw); |
| struct pll_14nm_cached_state *cached_state = &pll_14nm->cached_state; |
| void __iomem *cmn_base = pll_14nm->phy->base; |
| u32 data; |
| int ret; |
| |
| ret = dsi_pll_14nm_vco_set_rate(phy->vco_hw, |
| cached_state->vco_rate, 0); |
| if (ret) { |
| DRM_DEV_ERROR(&pll_14nm->phy->pdev->dev, |
| "restore vco rate failed. ret=%d\n", ret); |
| return ret; |
| } |
| |
| data = cached_state->n1postdiv | (cached_state->n2postdiv << 4); |
| |
| DBG("DSI%d PLL restore state %x %x", pll_14nm->phy->id, |
| cached_state->n1postdiv, cached_state->n2postdiv); |
| |
| writel(data, cmn_base + REG_DSI_14nm_PHY_CMN_CLK_CFG0); |
| |
| /* also restore post-dividers for slave DSI PLL */ |
| if (phy->usecase == MSM_DSI_PHY_MASTER) { |
| struct dsi_pll_14nm *pll_14nm_slave = pll_14nm->slave; |
| void __iomem *slave_base = pll_14nm_slave->phy->base; |
| |
| writel(data, slave_base + REG_DSI_14nm_PHY_CMN_CLK_CFG0); |
| } |
| |
| return 0; |
| } |
| |
| static int dsi_14nm_set_usecase(struct msm_dsi_phy *phy) |
| { |
| struct dsi_pll_14nm *pll_14nm = to_pll_14nm(phy->vco_hw); |
| void __iomem *base = phy->pll_base; |
| u32 clkbuflr_en, bandgap = 0; |
| |
| switch (phy->usecase) { |
| case MSM_DSI_PHY_STANDALONE: |
| clkbuflr_en = 0x1; |
| break; |
| case MSM_DSI_PHY_MASTER: |
| clkbuflr_en = 0x3; |
| pll_14nm->slave = pll_14nm_list[(pll_14nm->phy->id + 1) % DSI_MAX]; |
| break; |
| case MSM_DSI_PHY_SLAVE: |
| clkbuflr_en = 0x0; |
| bandgap = 0x3; |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| writel(clkbuflr_en, base + REG_DSI_14nm_PHY_PLL_CLKBUFLR_EN); |
| if (bandgap) |
| writel(bandgap, base + REG_DSI_14nm_PHY_PLL_PLL_BANDGAP); |
| |
| return 0; |
| } |
| |
| static struct clk_hw *pll_14nm_postdiv_register(struct dsi_pll_14nm *pll_14nm, |
| const char *name, |
| const struct clk_hw *parent_hw, |
| unsigned long flags, |
| u8 shift) |
| { |
| struct dsi_pll_14nm_postdiv *pll_postdiv; |
| struct device *dev = &pll_14nm->phy->pdev->dev; |
| struct clk_init_data postdiv_init = { |
| .parent_hws = (const struct clk_hw *[]) { parent_hw }, |
| .num_parents = 1, |
| .name = name, |
| .flags = flags, |
| .ops = &clk_ops_dsi_pll_14nm_postdiv, |
| }; |
| int ret; |
| |
| pll_postdiv = devm_kzalloc(dev, sizeof(*pll_postdiv), GFP_KERNEL); |
| if (!pll_postdiv) |
| return ERR_PTR(-ENOMEM); |
| |
| pll_postdiv->pll = pll_14nm; |
| pll_postdiv->shift = shift; |
| /* both N1 and N2 postdividers are 4 bits wide */ |
| pll_postdiv->width = 4; |
| /* range of each divider is from 1 to 15 */ |
| pll_postdiv->flags = CLK_DIVIDER_ONE_BASED; |
| pll_postdiv->hw.init = &postdiv_init; |
| |
| ret = devm_clk_hw_register(dev, &pll_postdiv->hw); |
| if (ret) |
| return ERR_PTR(ret); |
| |
| return &pll_postdiv->hw; |
| } |
| |
| static int pll_14nm_register(struct dsi_pll_14nm *pll_14nm, struct clk_hw **provided_clocks) |
| { |
| char clk_name[32]; |
| struct clk_init_data vco_init = { |
| .parent_data = &(const struct clk_parent_data) { |
| .fw_name = "ref", |
| }, |
| .num_parents = 1, |
| .name = clk_name, |
| .flags = CLK_IGNORE_UNUSED, |
| .ops = &clk_ops_dsi_pll_14nm_vco, |
| }; |
| struct device *dev = &pll_14nm->phy->pdev->dev; |
| struct clk_hw *hw, *n1_postdiv, *n1_postdivby2; |
| int ret; |
| |
| DBG("DSI%d", pll_14nm->phy->id); |
| |
| snprintf(clk_name, sizeof(clk_name), "dsi%dvco_clk", pll_14nm->phy->id); |
| pll_14nm->clk_hw.init = &vco_init; |
| |
| ret = devm_clk_hw_register(dev, &pll_14nm->clk_hw); |
| if (ret) |
| return ret; |
| |
| snprintf(clk_name, sizeof(clk_name), "dsi%dn1_postdiv_clk", pll_14nm->phy->id); |
| |
| /* N1 postdiv, bits 0-3 in REG_DSI_14nm_PHY_CMN_CLK_CFG0 */ |
| n1_postdiv = pll_14nm_postdiv_register(pll_14nm, clk_name, |
| &pll_14nm->clk_hw, CLK_SET_RATE_PARENT, 0); |
| if (IS_ERR(n1_postdiv)) |
| return PTR_ERR(n1_postdiv); |
| |
| snprintf(clk_name, sizeof(clk_name), "dsi%dpllbyte", pll_14nm->phy->id); |
| |
| /* DSI Byte clock = VCO_CLK / N1 / 8 */ |
| hw = devm_clk_hw_register_fixed_factor_parent_hw(dev, clk_name, |
| n1_postdiv, CLK_SET_RATE_PARENT, 1, 8); |
| if (IS_ERR(hw)) |
| return PTR_ERR(hw); |
| |
| provided_clocks[DSI_BYTE_PLL_CLK] = hw; |
| |
| snprintf(clk_name, sizeof(clk_name), "dsi%dn1_postdivby2_clk", pll_14nm->phy->id); |
| |
| /* |
| * Skip the mux for now, force DSICLK_SEL to 1, Add a /2 divider |
| * on the way. Don't let it set parent. |
| */ |
| n1_postdivby2 = devm_clk_hw_register_fixed_factor_parent_hw(dev, |
| clk_name, n1_postdiv, 0, 1, 2); |
| if (IS_ERR(n1_postdivby2)) |
| return PTR_ERR(n1_postdivby2); |
| |
| snprintf(clk_name, sizeof(clk_name), "dsi%dpll", pll_14nm->phy->id); |
| |
| /* DSI pixel clock = VCO_CLK / N1 / 2 / N2 |
| * This is the output of N2 post-divider, bits 4-7 in |
| * REG_DSI_14nm_PHY_CMN_CLK_CFG0. Don't let it set parent. |
| */ |
| hw = pll_14nm_postdiv_register(pll_14nm, clk_name, n1_postdivby2, |
| 0, 4); |
| if (IS_ERR(hw)) |
| return PTR_ERR(hw); |
| |
| provided_clocks[DSI_PIXEL_PLL_CLK] = hw; |
| |
| return 0; |
| } |
| |
| static int dsi_pll_14nm_init(struct msm_dsi_phy *phy) |
| { |
| struct platform_device *pdev = phy->pdev; |
| struct dsi_pll_14nm *pll_14nm; |
| int ret; |
| |
| if (!pdev) |
| return -ENODEV; |
| |
| pll_14nm = devm_kzalloc(&pdev->dev, sizeof(*pll_14nm), GFP_KERNEL); |
| if (!pll_14nm) |
| return -ENOMEM; |
| |
| DBG("PLL%d", phy->id); |
| |
| pll_14nm_list[phy->id] = pll_14nm; |
| |
| spin_lock_init(&pll_14nm->postdiv_lock); |
| |
| pll_14nm->phy = phy; |
| |
| ret = pll_14nm_register(pll_14nm, phy->provided_clocks->hws); |
| if (ret) { |
| DRM_DEV_ERROR(&pdev->dev, "failed to register PLL: %d\n", ret); |
| return ret; |
| } |
| |
| phy->vco_hw = &pll_14nm->clk_hw; |
| |
| return 0; |
| } |
| |
| static void dsi_14nm_dphy_set_timing(struct msm_dsi_phy *phy, |
| struct msm_dsi_dphy_timing *timing, |
| int lane_idx) |
| { |
| void __iomem *base = phy->lane_base; |
| bool clk_ln = (lane_idx == PHY_14NM_CKLN_IDX); |
| u32 zero = clk_ln ? timing->clk_zero : timing->hs_zero; |
| u32 prepare = clk_ln ? timing->clk_prepare : timing->hs_prepare; |
| u32 trail = clk_ln ? timing->clk_trail : timing->hs_trail; |
| u32 rqst = clk_ln ? timing->hs_rqst_ckln : timing->hs_rqst; |
| u32 prep_dly = clk_ln ? timing->hs_prep_dly_ckln : timing->hs_prep_dly; |
| u32 halfbyte_en = clk_ln ? timing->hs_halfbyte_en_ckln : |
| timing->hs_halfbyte_en; |
| |
| writel(DSI_14nm_PHY_LN_TIMING_CTRL_4_HS_EXIT(timing->hs_exit), |
| base + REG_DSI_14nm_PHY_LN_TIMING_CTRL_4(lane_idx)); |
| writel(DSI_14nm_PHY_LN_TIMING_CTRL_5_HS_ZERO(zero), |
| base + REG_DSI_14nm_PHY_LN_TIMING_CTRL_5(lane_idx)); |
| writel(DSI_14nm_PHY_LN_TIMING_CTRL_6_HS_PREPARE(prepare), |
| base + REG_DSI_14nm_PHY_LN_TIMING_CTRL_6(lane_idx)); |
| writel(DSI_14nm_PHY_LN_TIMING_CTRL_7_HS_TRAIL(trail), |
| base + REG_DSI_14nm_PHY_LN_TIMING_CTRL_7(lane_idx)); |
| writel(DSI_14nm_PHY_LN_TIMING_CTRL_8_HS_RQST(rqst), |
| base + REG_DSI_14nm_PHY_LN_TIMING_CTRL_8(lane_idx)); |
| writel(DSI_14nm_PHY_LN_CFG0_PREPARE_DLY(prep_dly), |
| base + REG_DSI_14nm_PHY_LN_CFG0(lane_idx)); |
| writel(halfbyte_en ? DSI_14nm_PHY_LN_CFG1_HALFBYTECLK_EN : 0, |
| base + REG_DSI_14nm_PHY_LN_CFG1(lane_idx)); |
| writel(DSI_14nm_PHY_LN_TIMING_CTRL_9_TA_GO(timing->ta_go) | |
| DSI_14nm_PHY_LN_TIMING_CTRL_9_TA_SURE(timing->ta_sure), |
| base + REG_DSI_14nm_PHY_LN_TIMING_CTRL_9(lane_idx)); |
| writel(DSI_14nm_PHY_LN_TIMING_CTRL_10_TA_GET(timing->ta_get), |
| base + REG_DSI_14nm_PHY_LN_TIMING_CTRL_10(lane_idx)); |
| writel(DSI_14nm_PHY_LN_TIMING_CTRL_11_TRIG3_CMD(0xa0), |
| base + REG_DSI_14nm_PHY_LN_TIMING_CTRL_11(lane_idx)); |
| } |
| |
| static int dsi_14nm_phy_enable(struct msm_dsi_phy *phy, |
| struct msm_dsi_phy_clk_request *clk_req) |
| { |
| struct msm_dsi_dphy_timing *timing = &phy->timing; |
| u32 data; |
| int i; |
| int ret; |
| void __iomem *base = phy->base; |
| void __iomem *lane_base = phy->lane_base; |
| u32 glbl_test_ctrl; |
| |
| if (msm_dsi_dphy_timing_calc_v2(timing, clk_req)) { |
| DRM_DEV_ERROR(&phy->pdev->dev, |
| "%s: D-PHY timing calculation failed\n", |
| __func__); |
| return -EINVAL; |
| } |
| |
| data = 0x1c; |
| if (phy->usecase != MSM_DSI_PHY_STANDALONE) |
| data |= DSI_14nm_PHY_CMN_LDO_CNTRL_VREG_CTRL(32); |
| writel(data, base + REG_DSI_14nm_PHY_CMN_LDO_CNTRL); |
| |
| writel(0x1, base + REG_DSI_14nm_PHY_CMN_GLBL_TEST_CTRL); |
| |
| /* 4 data lanes + 1 clk lane configuration */ |
| for (i = 0; i < 5; i++) { |
| writel(0x1d, lane_base + REG_DSI_14nm_PHY_LN_VREG_CNTRL(i)); |
| |
| writel(0xff, lane_base + REG_DSI_14nm_PHY_LN_STRENGTH_CTRL_0(i)); |
| writel(i == PHY_14NM_CKLN_IDX ? 0x00 : 0x06, |
| lane_base + REG_DSI_14nm_PHY_LN_STRENGTH_CTRL_1(i)); |
| |
| writel(i == PHY_14NM_CKLN_IDX ? 0x8f : 0x0f, |
| lane_base + REG_DSI_14nm_PHY_LN_CFG3(i)); |
| writel(0x10, lane_base + REG_DSI_14nm_PHY_LN_CFG2(i)); |
| writel(0, lane_base + REG_DSI_14nm_PHY_LN_TEST_DATAPATH(i)); |
| writel(0x88, lane_base + REG_DSI_14nm_PHY_LN_TEST_STR(i)); |
| |
| dsi_14nm_dphy_set_timing(phy, timing, i); |
| } |
| |
| /* Make sure PLL is not start */ |
| writel(0x00, base + REG_DSI_14nm_PHY_CMN_PLL_CNTRL); |
| |
| wmb(); /* make sure everything is written before reset and enable */ |
| |
| /* reset digital block */ |
| writel(0x80, base + REG_DSI_14nm_PHY_CMN_CTRL_1); |
| wmb(); /* ensure reset is asserted */ |
| udelay(100); |
| writel(0x00, base + REG_DSI_14nm_PHY_CMN_CTRL_1); |
| |
| glbl_test_ctrl = readl(base + REG_DSI_14nm_PHY_CMN_GLBL_TEST_CTRL); |
| if (phy->id == DSI_1 && phy->usecase == MSM_DSI_PHY_SLAVE) |
| glbl_test_ctrl |= DSI_14nm_PHY_CMN_GLBL_TEST_CTRL_BITCLK_HS_SEL; |
| else |
| glbl_test_ctrl &= ~DSI_14nm_PHY_CMN_GLBL_TEST_CTRL_BITCLK_HS_SEL; |
| writel(glbl_test_ctrl, base + REG_DSI_14nm_PHY_CMN_GLBL_TEST_CTRL); |
| ret = dsi_14nm_set_usecase(phy); |
| if (ret) { |
| DRM_DEV_ERROR(&phy->pdev->dev, "%s: set pll usecase failed, %d\n", |
| __func__, ret); |
| return ret; |
| } |
| |
| /* Remove power down from PLL and all lanes */ |
| writel(0xff, base + REG_DSI_14nm_PHY_CMN_CTRL_0); |
| |
| return 0; |
| } |
| |
| static void dsi_14nm_phy_disable(struct msm_dsi_phy *phy) |
| { |
| writel(0, phy->base + REG_DSI_14nm_PHY_CMN_GLBL_TEST_CTRL); |
| writel(0, phy->base + REG_DSI_14nm_PHY_CMN_CTRL_0); |
| |
| /* ensure that the phy is completely disabled */ |
| wmb(); |
| } |
| |
| static const struct regulator_bulk_data dsi_phy_14nm_17mA_regulators[] = { |
| { .supply = "vcca", .init_load_uA = 17000 }, |
| }; |
| |
| static const struct regulator_bulk_data dsi_phy_14nm_73p4mA_regulators[] = { |
| { .supply = "vcca", .init_load_uA = 73400 }, |
| }; |
| |
| const struct msm_dsi_phy_cfg dsi_phy_14nm_cfgs = { |
| .has_phy_lane = true, |
| .regulator_data = dsi_phy_14nm_17mA_regulators, |
| .num_regulators = ARRAY_SIZE(dsi_phy_14nm_17mA_regulators), |
| .ops = { |
| .enable = dsi_14nm_phy_enable, |
| .disable = dsi_14nm_phy_disable, |
| .pll_init = dsi_pll_14nm_init, |
| .save_pll_state = dsi_14nm_pll_save_state, |
| .restore_pll_state = dsi_14nm_pll_restore_state, |
| }, |
| .min_pll_rate = VCO_MIN_RATE, |
| .max_pll_rate = VCO_MAX_RATE, |
| .io_start = { 0x994400, 0x996400 }, |
| .num_dsi_phy = 2, |
| }; |
| |
| const struct msm_dsi_phy_cfg dsi_phy_14nm_660_cfgs = { |
| .has_phy_lane = true, |
| .regulator_data = dsi_phy_14nm_73p4mA_regulators, |
| .num_regulators = ARRAY_SIZE(dsi_phy_14nm_73p4mA_regulators), |
| .ops = { |
| .enable = dsi_14nm_phy_enable, |
| .disable = dsi_14nm_phy_disable, |
| .pll_init = dsi_pll_14nm_init, |
| .save_pll_state = dsi_14nm_pll_save_state, |
| .restore_pll_state = dsi_14nm_pll_restore_state, |
| }, |
| .min_pll_rate = VCO_MIN_RATE, |
| .max_pll_rate = VCO_MAX_RATE, |
| .io_start = { 0xc994400, 0xc996400 }, |
| .num_dsi_phy = 2, |
| }; |
| |
| const struct msm_dsi_phy_cfg dsi_phy_14nm_8953_cfgs = { |
| .has_phy_lane = true, |
| .regulator_data = dsi_phy_14nm_17mA_regulators, |
| .num_regulators = ARRAY_SIZE(dsi_phy_14nm_17mA_regulators), |
| .ops = { |
| .enable = dsi_14nm_phy_enable, |
| .disable = dsi_14nm_phy_disable, |
| .pll_init = dsi_pll_14nm_init, |
| .save_pll_state = dsi_14nm_pll_save_state, |
| .restore_pll_state = dsi_14nm_pll_restore_state, |
| }, |
| .min_pll_rate = VCO_MIN_RATE, |
| .max_pll_rate = VCO_MAX_RATE, |
| .io_start = { 0x1a94400, 0x1a96400 }, |
| .num_dsi_phy = 2, |
| }; |
| |
| const struct msm_dsi_phy_cfg dsi_phy_14nm_2290_cfgs = { |
| .has_phy_lane = true, |
| .ops = { |
| .enable = dsi_14nm_phy_enable, |
| .disable = dsi_14nm_phy_disable, |
| .pll_init = dsi_pll_14nm_init, |
| .save_pll_state = dsi_14nm_pll_save_state, |
| .restore_pll_state = dsi_14nm_pll_restore_state, |
| }, |
| .min_pll_rate = VCO_MIN_RATE, |
| .max_pll_rate = VCO_MAX_RATE, |
| .io_start = { 0x5e94400 }, |
| .num_dsi_phy = 1, |
| }; |