| # SPDX-License-Identifier: GPL-2.0-only |
| # |
| # TI device configuration |
| # |
| |
| config NET_VENDOR_TI |
| bool "Texas Instruments (TI) devices" |
| default y |
| depends on PCI || EISA || ARCH_DAVINCI || ARCH_OMAP2PLUS || ARCH_KEYSTONE || ARCH_K3 |
| help |
| If you have a network (Ethernet) card belonging to this class, say Y. |
| |
| Note that the answer to this question doesn't directly affect the |
| kernel: saying N will just cause the configurator to skip all |
| the questions about TI devices. If you say Y, you will be asked for |
| your specific card in the following questions. |
| |
| if NET_VENDOR_TI |
| |
| config TI_DAVINCI_EMAC |
| tristate "TI DaVinci EMAC Support" |
| depends on ARM && ( ARCH_DAVINCI || ARCH_OMAP3 ) || COMPILE_TEST |
| select TI_DAVINCI_MDIO |
| select PHYLIB |
| select GENERIC_ALLOCATOR |
| help |
| This driver supports TI's DaVinci Ethernet . |
| |
| To compile this driver as a module, choose M here: the module |
| will be called davinci_emac_driver. This is recommended. |
| |
| config TI_DAVINCI_MDIO |
| tristate "TI DaVinci MDIO Support" |
| depends on ARCH_DAVINCI || ARCH_OMAP2PLUS || ARCH_KEYSTONE || ARCH_K3 || COMPILE_TEST |
| select PHYLIB |
| select MDIO_BITBANG |
| help |
| This driver supports TI's DaVinci MDIO module. |
| |
| To compile this driver as a module, choose M here: the module |
| will be called davinci_mdio. This is recommended. |
| |
| config TI_CPSW_PHY_SEL |
| bool "TI CPSW Phy mode Selection (DEPRECATED)" |
| default n |
| help |
| This driver supports configuring of the phy mode connected to |
| the CPSW. DEPRECATED: use PHY_TI_GMII_SEL. |
| |
| config TI_CPSW |
| tristate "TI CPSW Switch Support" |
| depends on ARCH_DAVINCI || ARCH_OMAP2PLUS || COMPILE_TEST |
| depends on TI_CPTS || !TI_CPTS |
| select TI_DAVINCI_MDIO |
| select MFD_SYSCON |
| select PAGE_POOL |
| select REGMAP |
| imply PHY_TI_GMII_SEL |
| help |
| This driver supports TI's CPSW Ethernet Switch. |
| |
| To compile this driver as a module, choose M here: the module |
| will be called cpsw. |
| |
| config TI_CPSW_SWITCHDEV |
| tristate "TI CPSW Switch Support with switchdev" |
| depends on ARCH_DAVINCI || ARCH_OMAP2PLUS || COMPILE_TEST |
| depends on NET_SWITCHDEV |
| depends on TI_CPTS || !TI_CPTS |
| select PAGE_POOL |
| select TI_DAVINCI_MDIO |
| select MFD_SYSCON |
| select REGMAP |
| select NET_DEVLINK |
| imply PHY_TI_GMII_SEL |
| help |
| This driver supports TI's CPSW Ethernet Switch. |
| |
| To compile this driver as a module, choose M here: the module |
| will be called cpsw_new. |
| |
| config TI_CPTS |
| tristate "TI Common Platform Time Sync (CPTS) Support" |
| depends on ARCH_OMAP2PLUS || ARCH_KEYSTONE || COMPILE_TEST |
| depends on COMMON_CLK |
| depends on PTP_1588_CLOCK |
| help |
| This driver supports the Common Platform Time Sync unit of |
| the CPSW Ethernet Switch and Keystone 2 1g/10g Switch Subsystem. |
| The unit can time stamp PTP UDP/IPv4 and Layer 2 packets, and the |
| driver offers a PTP Hardware Clock. |
| |
| config TI_K3_CPPI_DESC_POOL |
| tristate |
| |
| config TI_K3_AM65_CPSW_NUSS |
| tristate "TI K3 AM654x/J721E CPSW Ethernet driver" |
| depends on ARCH_K3 && OF && TI_K3_UDMA_GLUE_LAYER |
| select NET_DEVLINK |
| select TI_DAVINCI_MDIO |
| select PHYLINK |
| select TI_K3_CPPI_DESC_POOL |
| imply PHY_TI_GMII_SEL |
| depends on TI_K3_AM65_CPTS || !TI_K3_AM65_CPTS |
| help |
| This driver supports TI K3 AM654/J721E CPSW2G Ethernet SubSystem. |
| The two-port Gigabit Ethernet MAC (MCU_CPSW0) subsystem provides |
| Ethernet packet communication for the device: One Ethernet port |
| (port 1) with selectable RGMII and RMII interfaces and an internal |
| Communications Port Programming Interface (CPPI) port (port 0). |
| |
| To compile this driver as a module, choose M here: the module |
| will be called ti-am65-cpsw-nuss. |
| |
| config TI_K3_AM65_CPSW_SWITCHDEV |
| bool "TI K3 AM654x/J721E CPSW Switch mode support" |
| depends on TI_K3_AM65_CPSW_NUSS |
| depends on NET_SWITCHDEV |
| help |
| This enables switchdev support for TI K3 CPSWxG Ethernet |
| Switch. Enable this driver to support hardware switch support for AM65 |
| CPSW NUSS driver. |
| |
| config TI_K3_AM65_CPTS |
| tristate "TI K3 AM65x CPTS" |
| depends on ARCH_K3 && OF |
| depends on PTP_1588_CLOCK |
| help |
| Say y here to support the TI K3 AM65x CPTS with 1588 features such as |
| PTP hardware clock for each CPTS device and network packets |
| timestamping where applicable. |
| Depending on integration CPTS blocks enable compliance with |
| the IEEE 1588-2008 standard for a precision clock synchronization |
| protocol, Ethernet Enhanced Scheduled Traffic Operations (CPTS_ESTFn) |
| and PCIe Subsystem Precision Time Measurement (PTM). |
| |
| config TI_AM65_CPSW_QOS |
| bool "Enable QoS offload features in AM65 CPSW" |
| depends on TI_K3_AM65_CPSW_NUSS && NET_SCH_TAPRIO && TI_K3_AM65_CPTS |
| help |
| This option enables QoS offload features in AM65 CPSW like |
| Time Aware Shaper (TAS) / Enhanced Scheduled Traffic (EST), |
| MQPRIO qdisc offload and Frame-Preemption MAC Merge / Interspersing |
| Express Traffic (IET). |
| The EST scheduler runs on CPTS and the TAS/EST schedule is |
| updated in the Fetch RAM memory of the CPSW. |
| |
| config TI_KEYSTONE_NETCP |
| tristate "TI Keystone NETCP Core Support" |
| select TI_DAVINCI_MDIO |
| depends on OF |
| depends on KEYSTONE_NAVIGATOR_DMA && KEYSTONE_NAVIGATOR_QMSS |
| depends on TI_CPTS || !TI_CPTS |
| help |
| This driver supports TI's Keystone NETCP Core. |
| |
| To compile this driver as a module, choose M here: the module |
| will be called keystone_netcp. |
| |
| config TI_KEYSTONE_NETCP_ETHSS |
| depends on TI_KEYSTONE_NETCP |
| tristate "TI Keystone NETCP Ethernet subsystem Support" |
| help |
| |
| To compile this driver as a module, choose M here: the module |
| will be called keystone_netcp_ethss. |
| |
| config TLAN |
| tristate "TI ThunderLAN support" |
| depends on (PCI || EISA) && HAS_IOPORT |
| help |
| If you have a PCI Ethernet network card based on the ThunderLAN chip |
| which is supported by this driver, say Y here. |
| |
| Devices currently supported by this driver are Compaq Netelligent, |
| Compaq NetFlex and Olicom cards. Please read the file |
| <file:Documentation/networking/device_drivers/ethernet/ti/tlan.rst> |
| for more details. |
| |
| To compile this driver as a module, choose M here. The module |
| will be called tlan. |
| |
| Please email feedback to <torben.mathiasen@compaq.com>. |
| |
| config TI_ICSSG_PRUETH |
| tristate "TI Gigabit PRU Ethernet driver" |
| select PHYLIB |
| select TI_ICSS_IEP |
| select TI_K3_CPPI_DESC_POOL |
| depends on PRU_REMOTEPROC |
| depends on NET_SWITCHDEV |
| depends on ARCH_K3 && OF && TI_K3_UDMA_GLUE_LAYER |
| depends on PTP_1588_CLOCK_OPTIONAL |
| help |
| Support dual Gigabit Ethernet ports over the ICSSG PRU Subsystem. |
| This subsystem is available starting with the AM65 platform. |
| |
| This driver requires firmware binaries which will run on the PRUs |
| to support the Ethernet operation. Currently, it supports Ethernet |
| with 1G and 100M link speed. |
| |
| config TI_ICSSG_PRUETH_SR1 |
| tristate "TI Gigabit PRU SR1.0 Ethernet driver" |
| select PHYLIB |
| select TI_ICSS_IEP |
| select TI_K3_CPPI_DESC_POOL |
| depends on PRU_REMOTEPROC |
| depends on NET_SWITCHDEV |
| depends on ARCH_K3 && OF && TI_K3_UDMA_GLUE_LAYER |
| help |
| Support dual Gigabit Ethernet ports over the ICSSG PRU Subsystem. |
| This subsystem is available on the AM65 SR1.0 platform. |
| |
| This driver requires firmware binaries which will run on the PRUs |
| to support the Ethernet operation. Currently, it supports Ethernet |
| with 1G, 100M and 10M link speed. |
| |
| config TI_ICSS_IEP |
| tristate "TI PRU ICSS IEP driver" |
| depends on PTP_1588_CLOCK_OPTIONAL |
| depends on TI_PRUSS |
| default TI_PRUSS |
| help |
| This driver enables support for the PRU-ICSS Industrial Ethernet |
| Peripheral within a PRU-ICSS subsystem present on various TI SoCs. |
| |
| To compile this driver as a module, choose M here. The module |
| will be called icss_iep. |
| |
| endif # NET_VENDOR_TI |
