| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Debugfs interface |
| * |
| * Copyright (C) 2020, Intel Corporation |
| * Authors: Gil Fine <gil.fine@intel.com> |
| * Mika Westerberg <mika.westerberg@linux.intel.com> |
| */ |
| |
| #include <linux/bitfield.h> |
| #include <linux/debugfs.h> |
| #include <linux/delay.h> |
| #include <linux/pm_runtime.h> |
| #include <linux/uaccess.h> |
| |
| #include "tb.h" |
| #include "sb_regs.h" |
| |
| #define PORT_CAP_V1_PCIE_LEN 1 |
| #define PORT_CAP_V2_PCIE_LEN 2 |
| #define PORT_CAP_POWER_LEN 2 |
| #define PORT_CAP_LANE_LEN 3 |
| #define PORT_CAP_USB3_LEN 5 |
| #define PORT_CAP_DP_V1_LEN 9 |
| #define PORT_CAP_DP_V2_LEN 14 |
| #define PORT_CAP_TMU_V1_LEN 8 |
| #define PORT_CAP_TMU_V2_LEN 10 |
| #define PORT_CAP_BASIC_LEN 9 |
| #define PORT_CAP_USB4_LEN 20 |
| |
| #define SWITCH_CAP_TMU_LEN 26 |
| #define SWITCH_CAP_BASIC_LEN 27 |
| |
| #define PATH_LEN 2 |
| |
| #define COUNTER_SET_LEN 3 |
| |
| /* |
| * USB4 spec doesn't specify dwell range, the range of 100 ms to 500 ms |
| * probed to give good results. |
| */ |
| #define MIN_DWELL_TIME 100 /* ms */ |
| #define MAX_DWELL_TIME 500 /* ms */ |
| #define DWELL_SAMPLE_INTERVAL 10 |
| |
| /* Sideband registers and their sizes as defined in the USB4 spec */ |
| struct sb_reg { |
| unsigned int reg; |
| unsigned int size; |
| }; |
| |
| #define SB_MAX_SIZE 64 |
| |
| /* Sideband registers for router */ |
| static const struct sb_reg port_sb_regs[] = { |
| { USB4_SB_VENDOR_ID, 4 }, |
| { USB4_SB_PRODUCT_ID, 4 }, |
| { USB4_SB_DEBUG_CONF, 4 }, |
| { USB4_SB_DEBUG, 54 }, |
| { USB4_SB_LRD_TUNING, 4 }, |
| { USB4_SB_OPCODE, 4 }, |
| { USB4_SB_METADATA, 4 }, |
| { USB4_SB_LINK_CONF, 3 }, |
| { USB4_SB_GEN23_TXFFE, 4 }, |
| { USB4_SB_GEN4_TXFFE, 4 }, |
| { USB4_SB_VERSION, 4 }, |
| { USB4_SB_DATA, 64 }, |
| }; |
| |
| /* Sideband registers for retimer */ |
| static const struct sb_reg retimer_sb_regs[] = { |
| { USB4_SB_VENDOR_ID, 4 }, |
| { USB4_SB_PRODUCT_ID, 4 }, |
| { USB4_SB_FW_VERSION, 4 }, |
| { USB4_SB_LRD_TUNING, 4 }, |
| { USB4_SB_OPCODE, 4 }, |
| { USB4_SB_METADATA, 4 }, |
| { USB4_SB_GEN23_TXFFE, 4 }, |
| { USB4_SB_GEN4_TXFFE, 4 }, |
| { USB4_SB_VERSION, 4 }, |
| { USB4_SB_DATA, 64 }, |
| }; |
| |
| #define DEBUGFS_ATTR(__space, __write) \ |
| static int __space ## _open(struct inode *inode, struct file *file) \ |
| { \ |
| return single_open(file, __space ## _show, inode->i_private); \ |
| } \ |
| \ |
| static const struct file_operations __space ## _fops = { \ |
| .owner = THIS_MODULE, \ |
| .open = __space ## _open, \ |
| .release = single_release, \ |
| .read = seq_read, \ |
| .write = __write, \ |
| .llseek = seq_lseek, \ |
| } |
| |
| #define DEBUGFS_ATTR_RO(__space) \ |
| DEBUGFS_ATTR(__space, NULL) |
| |
| #define DEBUGFS_ATTR_RW(__space) \ |
| DEBUGFS_ATTR(__space, __space ## _write) |
| |
| static struct dentry *tb_debugfs_root; |
| |
| static void *validate_and_copy_from_user(const void __user *user_buf, |
| size_t *count) |
| { |
| size_t nbytes; |
| void *buf; |
| |
| if (!*count) |
| return ERR_PTR(-EINVAL); |
| |
| if (!access_ok(user_buf, *count)) |
| return ERR_PTR(-EFAULT); |
| |
| buf = (void *)get_zeroed_page(GFP_KERNEL); |
| if (!buf) |
| return ERR_PTR(-ENOMEM); |
| |
| nbytes = min_t(size_t, *count, PAGE_SIZE); |
| if (copy_from_user(buf, user_buf, nbytes)) { |
| free_page((unsigned long)buf); |
| return ERR_PTR(-EFAULT); |
| } |
| |
| *count = nbytes; |
| return buf; |
| } |
| |
| static bool parse_line(char **line, u32 *offs, u32 *val, int short_fmt_len, |
| int long_fmt_len) |
| { |
| char *token; |
| u32 v[5]; |
| int ret; |
| |
| token = strsep(line, "\n"); |
| if (!token) |
| return false; |
| |
| /* |
| * For Adapter/Router configuration space: |
| * Short format is: offset value\n |
| * v[0] v[1] |
| * Long format as produced from the read side: |
| * offset relative_offset cap_id vs_cap_id value\n |
| * v[0] v[1] v[2] v[3] v[4] |
| * |
| * For Counter configuration space: |
| * Short format is: offset\n |
| * v[0] |
| * Long format as produced from the read side: |
| * offset relative_offset counter_id value\n |
| * v[0] v[1] v[2] v[3] |
| */ |
| ret = sscanf(token, "%i %i %i %i %i", &v[0], &v[1], &v[2], &v[3], &v[4]); |
| /* In case of Counters, clear counter, "val" content is NA */ |
| if (ret == short_fmt_len) { |
| *offs = v[0]; |
| *val = v[short_fmt_len - 1]; |
| return true; |
| } else if (ret == long_fmt_len) { |
| *offs = v[0]; |
| *val = v[long_fmt_len - 1]; |
| return true; |
| } |
| |
| return false; |
| } |
| |
| #if IS_ENABLED(CONFIG_USB4_DEBUGFS_WRITE) |
| static ssize_t regs_write(struct tb_switch *sw, struct tb_port *port, |
| const char __user *user_buf, size_t count, |
| loff_t *ppos) |
| { |
| struct tb *tb = sw->tb; |
| char *line, *buf; |
| u32 val, offset; |
| int ret = 0; |
| |
| buf = validate_and_copy_from_user(user_buf, &count); |
| if (IS_ERR(buf)) |
| return PTR_ERR(buf); |
| |
| pm_runtime_get_sync(&sw->dev); |
| |
| if (mutex_lock_interruptible(&tb->lock)) { |
| ret = -ERESTARTSYS; |
| goto out; |
| } |
| |
| /* User did hardware changes behind the driver's back */ |
| add_taint(TAINT_USER, LOCKDEP_STILL_OK); |
| |
| line = buf; |
| while (parse_line(&line, &offset, &val, 2, 5)) { |
| if (port) |
| ret = tb_port_write(port, &val, TB_CFG_PORT, offset, 1); |
| else |
| ret = tb_sw_write(sw, &val, TB_CFG_SWITCH, offset, 1); |
| if (ret) |
| break; |
| } |
| |
| mutex_unlock(&tb->lock); |
| |
| out: |
| pm_runtime_mark_last_busy(&sw->dev); |
| pm_runtime_put_autosuspend(&sw->dev); |
| free_page((unsigned long)buf); |
| |
| return ret < 0 ? ret : count; |
| } |
| |
| static ssize_t port_regs_write(struct file *file, const char __user *user_buf, |
| size_t count, loff_t *ppos) |
| { |
| struct seq_file *s = file->private_data; |
| struct tb_port *port = s->private; |
| |
| return regs_write(port->sw, port, user_buf, count, ppos); |
| } |
| |
| static ssize_t switch_regs_write(struct file *file, const char __user *user_buf, |
| size_t count, loff_t *ppos) |
| { |
| struct seq_file *s = file->private_data; |
| struct tb_switch *sw = s->private; |
| |
| return regs_write(sw, NULL, user_buf, count, ppos); |
| } |
| |
| static bool parse_sb_line(char **line, u8 *reg, u8 *data, size_t data_size, |
| size_t *bytes_read) |
| { |
| char *field, *token; |
| int i; |
| |
| token = strsep(line, "\n"); |
| if (!token) |
| return false; |
| |
| /* Parse the register first */ |
| field = strsep(&token, " "); |
| if (!field) |
| return false; |
| if (kstrtou8(field, 0, reg)) |
| return false; |
| |
| /* Then the values for the register, up to data_size */ |
| for (i = 0; i < data_size; i++) { |
| field = strsep(&token, " "); |
| if (!field) |
| break; |
| if (kstrtou8(field, 0, &data[i])) |
| return false; |
| } |
| |
| *bytes_read = i; |
| return true; |
| } |
| |
| static ssize_t sb_regs_write(struct tb_port *port, const struct sb_reg *sb_regs, |
| size_t size, enum usb4_sb_target target, u8 index, |
| char *buf, size_t count, loff_t *ppos) |
| { |
| u8 reg, data[SB_MAX_SIZE]; |
| size_t bytes_read; |
| char *line = buf; |
| |
| /* User did hardware changes behind the driver's back */ |
| add_taint(TAINT_USER, LOCKDEP_STILL_OK); |
| |
| /* |
| * For sideband registers we accept: |
| * reg b0 b1 b2...\n |
| * |
| * Here "reg" is the byte offset of the sideband register and "b0".. |
| * are the byte values. There can be less byte values than the register |
| * size. The leftovers will not be overwritten. |
| */ |
| while (parse_sb_line(&line, ®, data, ARRAY_SIZE(data), &bytes_read)) { |
| const struct sb_reg *sb_reg; |
| int ret; |
| |
| /* At least one byte must be passed */ |
| if (bytes_read < 1) |
| return -EINVAL; |
| |
| /* Find the register */ |
| sb_reg = NULL; |
| for (int i = 0; i < size; i++) { |
| if (sb_regs[i].reg == reg) { |
| sb_reg = &sb_regs[i]; |
| break; |
| } |
| } |
| |
| if (!sb_reg) |
| return -EINVAL; |
| |
| if (bytes_read > sb_regs->size) |
| return -E2BIG; |
| |
| ret = usb4_port_sb_write(port, target, index, sb_reg->reg, data, |
| bytes_read); |
| if (ret) |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static ssize_t port_sb_regs_write(struct file *file, const char __user *user_buf, |
| size_t count, loff_t *ppos) |
| { |
| struct seq_file *s = file->private_data; |
| struct tb_port *port = s->private; |
| struct tb_switch *sw = port->sw; |
| struct tb *tb = sw->tb; |
| char *buf; |
| int ret; |
| |
| buf = validate_and_copy_from_user(user_buf, &count); |
| if (IS_ERR(buf)) |
| return PTR_ERR(buf); |
| |
| pm_runtime_get_sync(&sw->dev); |
| |
| if (mutex_lock_interruptible(&tb->lock)) { |
| ret = -ERESTARTSYS; |
| goto out; |
| } |
| |
| ret = sb_regs_write(port, port_sb_regs, ARRAY_SIZE(port_sb_regs), |
| USB4_SB_TARGET_ROUTER, 0, buf, count, ppos); |
| |
| mutex_unlock(&tb->lock); |
| out: |
| pm_runtime_mark_last_busy(&sw->dev); |
| pm_runtime_put_autosuspend(&sw->dev); |
| free_page((unsigned long)buf); |
| |
| return ret < 0 ? ret : count; |
| } |
| |
| static ssize_t retimer_sb_regs_write(struct file *file, |
| const char __user *user_buf, |
| size_t count, loff_t *ppos) |
| { |
| struct seq_file *s = file->private_data; |
| struct tb_retimer *rt = s->private; |
| struct tb *tb = rt->tb; |
| char *buf; |
| int ret; |
| |
| buf = validate_and_copy_from_user(user_buf, &count); |
| if (IS_ERR(buf)) |
| return PTR_ERR(buf); |
| |
| pm_runtime_get_sync(&rt->dev); |
| |
| if (mutex_lock_interruptible(&tb->lock)) { |
| ret = -ERESTARTSYS; |
| goto out; |
| } |
| |
| ret = sb_regs_write(rt->port, retimer_sb_regs, ARRAY_SIZE(retimer_sb_regs), |
| USB4_SB_TARGET_RETIMER, rt->index, buf, count, ppos); |
| |
| mutex_unlock(&tb->lock); |
| out: |
| pm_runtime_mark_last_busy(&rt->dev); |
| pm_runtime_put_autosuspend(&rt->dev); |
| free_page((unsigned long)buf); |
| |
| return ret < 0 ? ret : count; |
| } |
| #define DEBUGFS_MODE 0600 |
| #else |
| #define port_regs_write NULL |
| #define switch_regs_write NULL |
| #define port_sb_regs_write NULL |
| #define retimer_sb_regs_write NULL |
| #define DEBUGFS_MODE 0400 |
| #endif |
| |
| #if IS_ENABLED(CONFIG_USB4_DEBUGFS_MARGINING) |
| /** |
| * struct tb_margining - Lane margining support |
| * @port: USB4 port through which the margining operations are run |
| * @target: Sideband target |
| * @index: Retimer index if taget is %USB4_SB_TARGET_RETIMER |
| * @dev: Pointer to the device that is the target (USB4 port or retimer) |
| * @caps: Port lane margining capabilities |
| * @results: Last lane margining results |
| * @lanes: %0, %1 or %7 (all) |
| * @min_ber_level: Minimum supported BER level contour value |
| * @max_ber_level: Maximum supported BER level contour value |
| * @ber_level: Current BER level contour value |
| * @voltage_steps: Number of mandatory voltage steps |
| * @max_voltage_offset: Maximum mandatory voltage offset (in mV) |
| * @voltage_steps_optional_range: Number of voltage steps for optional range |
| * @max_voltage_offset_optional_range: Maximum voltage offset for the optional |
| * range (in mV). |
| * @time_steps: Number of time margin steps |
| * @max_time_offset: Maximum time margin offset (in mUI) |
| * @voltage_time_offset: Offset for voltage / time for software margining |
| * @dwell_time: Dwell time for software margining (in ms) |
| * @error_counter: Error counter operation for software margining |
| * @optional_voltage_offset_range: Enable optional extended voltage range |
| * @software: %true if software margining is used instead of hardware |
| * @time: %true if time margining is used instead of voltage |
| * @right_high: %false if left/low margin test is performed, %true if |
| * right/high |
| */ |
| struct tb_margining { |
| struct tb_port *port; |
| enum usb4_sb_target target; |
| u8 index; |
| struct device *dev; |
| u32 caps[2]; |
| u32 results[2]; |
| unsigned int lanes; |
| unsigned int min_ber_level; |
| unsigned int max_ber_level; |
| unsigned int ber_level; |
| unsigned int voltage_steps; |
| unsigned int max_voltage_offset; |
| unsigned int voltage_steps_optional_range; |
| unsigned int max_voltage_offset_optional_range; |
| unsigned int time_steps; |
| unsigned int max_time_offset; |
| unsigned int voltage_time_offset; |
| unsigned int dwell_time; |
| enum usb4_margin_sw_error_counter error_counter; |
| bool optional_voltage_offset_range; |
| bool software; |
| bool time; |
| bool right_high; |
| }; |
| |
| static int margining_modify_error_counter(struct tb_margining *margining, |
| u32 lanes, enum usb4_margin_sw_error_counter error_counter) |
| { |
| struct usb4_port_margining_params params = { 0 }; |
| struct tb_port *port = margining->port; |
| u32 result; |
| |
| if (error_counter != USB4_MARGIN_SW_ERROR_COUNTER_CLEAR && |
| error_counter != USB4_MARGIN_SW_ERROR_COUNTER_STOP) |
| return -EOPNOTSUPP; |
| |
| params.error_counter = error_counter; |
| params.lanes = lanes; |
| |
| return usb4_port_sw_margin(port, margining->target, margining->index, |
| ¶ms, &result); |
| } |
| |
| static bool supports_software(const struct tb_margining *margining) |
| { |
| return margining->caps[0] & USB4_MARGIN_CAP_0_MODES_SW; |
| } |
| |
| static bool supports_hardware(const struct tb_margining *margining) |
| { |
| return margining->caps[0] & USB4_MARGIN_CAP_0_MODES_HW; |
| } |
| |
| static bool both_lanes(const struct tb_margining *margining) |
| { |
| return margining->caps[0] & USB4_MARGIN_CAP_0_2_LANES; |
| } |
| |
| static unsigned int |
| independent_voltage_margins(const struct tb_margining *margining) |
| { |
| return FIELD_GET(USB4_MARGIN_CAP_0_VOLTAGE_INDP_MASK, margining->caps[0]); |
| } |
| |
| static bool supports_time(const struct tb_margining *margining) |
| { |
| return margining->caps[0] & USB4_MARGIN_CAP_0_TIME; |
| } |
| |
| /* Only applicable if supports_time() returns true */ |
| static unsigned int |
| independent_time_margins(const struct tb_margining *margining) |
| { |
| return FIELD_GET(USB4_MARGIN_CAP_1_TIME_INDP_MASK, margining->caps[1]); |
| } |
| |
| static bool |
| supports_optional_voltage_offset_range(const struct tb_margining *margining) |
| { |
| return margining->caps[0] & USB4_MARGIN_CAP_0_OPT_VOLTAGE_SUPPORT; |
| } |
| |
| static ssize_t |
| margining_ber_level_write(struct file *file, const char __user *user_buf, |
| size_t count, loff_t *ppos) |
| { |
| struct seq_file *s = file->private_data; |
| struct tb_margining *margining = s->private; |
| struct tb *tb = margining->port->sw->tb; |
| unsigned int val; |
| int ret = 0; |
| char *buf; |
| |
| if (mutex_lock_interruptible(&tb->lock)) |
| return -ERESTARTSYS; |
| |
| if (margining->software) { |
| ret = -EINVAL; |
| goto out_unlock; |
| } |
| |
| buf = validate_and_copy_from_user(user_buf, &count); |
| if (IS_ERR(buf)) { |
| ret = PTR_ERR(buf); |
| goto out_unlock; |
| } |
| |
| buf[count - 1] = '\0'; |
| |
| ret = kstrtouint(buf, 10, &val); |
| if (ret) |
| goto out_free; |
| |
| if (val < margining->min_ber_level || |
| val > margining->max_ber_level) { |
| ret = -EINVAL; |
| goto out_free; |
| } |
| |
| margining->ber_level = val; |
| |
| out_free: |
| free_page((unsigned long)buf); |
| out_unlock: |
| mutex_unlock(&tb->lock); |
| |
| return ret < 0 ? ret : count; |
| } |
| |
| static void ber_level_show(struct seq_file *s, unsigned int val) |
| { |
| if (val % 2) |
| seq_printf(s, "3 * 1e%d (%u)\n", -12 + (val + 1) / 2, val); |
| else |
| seq_printf(s, "1e%d (%u)\n", -12 + val / 2, val); |
| } |
| |
| static int margining_ber_level_show(struct seq_file *s, void *not_used) |
| { |
| const struct tb_margining *margining = s->private; |
| |
| if (margining->software) |
| return -EINVAL; |
| ber_level_show(s, margining->ber_level); |
| return 0; |
| } |
| DEBUGFS_ATTR_RW(margining_ber_level); |
| |
| static int margining_caps_show(struct seq_file *s, void *not_used) |
| { |
| struct tb_margining *margining = s->private; |
| struct tb *tb = margining->port->sw->tb; |
| u32 cap0, cap1; |
| |
| if (mutex_lock_interruptible(&tb->lock)) |
| return -ERESTARTSYS; |
| |
| /* Dump the raw caps first */ |
| cap0 = margining->caps[0]; |
| seq_printf(s, "0x%08x\n", cap0); |
| cap1 = margining->caps[1]; |
| seq_printf(s, "0x%08x\n", cap1); |
| |
| seq_printf(s, "# software margining: %s\n", |
| supports_software(margining) ? "yes" : "no"); |
| if (supports_hardware(margining)) { |
| seq_puts(s, "# hardware margining: yes\n"); |
| seq_puts(s, "# minimum BER level contour: "); |
| ber_level_show(s, margining->min_ber_level); |
| seq_puts(s, "# maximum BER level contour: "); |
| ber_level_show(s, margining->max_ber_level); |
| } else { |
| seq_puts(s, "# hardware margining: no\n"); |
| } |
| |
| seq_printf(s, "# both lanes simultaneously: %s\n", |
| both_lanes(margining) ? "yes" : "no"); |
| seq_printf(s, "# voltage margin steps: %u\n", |
| margining->voltage_steps); |
| seq_printf(s, "# maximum voltage offset: %u mV\n", |
| margining->max_voltage_offset); |
| seq_printf(s, "# optional voltage offset range support: %s\n", |
| str_yes_no(supports_optional_voltage_offset_range(margining))); |
| if (supports_optional_voltage_offset_range(margining)) { |
| seq_printf(s, "# voltage margin steps, optional range: %u\n", |
| margining->voltage_steps_optional_range); |
| seq_printf(s, "# maximum voltage offset, optional range: %u mV\n", |
| margining->max_voltage_offset_optional_range); |
| } |
| |
| switch (independent_voltage_margins(margining)) { |
| case USB4_MARGIN_CAP_0_VOLTAGE_MIN: |
| seq_puts(s, "# returns minimum between high and low voltage margins\n"); |
| break; |
| case USB4_MARGIN_CAP_0_VOLTAGE_HL: |
| seq_puts(s, "# returns high or low voltage margin\n"); |
| break; |
| case USB4_MARGIN_CAP_0_VOLTAGE_BOTH: |
| seq_puts(s, "# returns both high and low margins\n"); |
| break; |
| } |
| |
| if (supports_time(margining)) { |
| seq_puts(s, "# time margining: yes\n"); |
| seq_printf(s, "# time margining is destructive: %s\n", |
| cap1 & USB4_MARGIN_CAP_1_TIME_DESTR ? "yes" : "no"); |
| |
| switch (independent_time_margins(margining)) { |
| case USB4_MARGIN_CAP_1_TIME_MIN: |
| seq_puts(s, "# returns minimum between left and right time margins\n"); |
| break; |
| case USB4_MARGIN_CAP_1_TIME_LR: |
| seq_puts(s, "# returns left or right margin\n"); |
| break; |
| case USB4_MARGIN_CAP_1_TIME_BOTH: |
| seq_puts(s, "# returns both left and right margins\n"); |
| break; |
| } |
| |
| seq_printf(s, "# time margin steps: %u\n", |
| margining->time_steps); |
| seq_printf(s, "# maximum time offset: %u mUI\n", |
| margining->max_time_offset); |
| } else { |
| seq_puts(s, "# time margining: no\n"); |
| } |
| |
| mutex_unlock(&tb->lock); |
| return 0; |
| } |
| DEBUGFS_ATTR_RO(margining_caps); |
| |
| static ssize_t |
| margining_lanes_write(struct file *file, const char __user *user_buf, |
| size_t count, loff_t *ppos) |
| { |
| struct seq_file *s = file->private_data; |
| struct tb_margining *margining = s->private; |
| struct tb *tb = margining->port->sw->tb; |
| int ret = 0; |
| char *buf; |
| |
| buf = validate_and_copy_from_user(user_buf, &count); |
| if (IS_ERR(buf)) |
| return PTR_ERR(buf); |
| |
| buf[count - 1] = '\0'; |
| |
| if (mutex_lock_interruptible(&tb->lock)) { |
| ret = -ERESTARTSYS; |
| goto out_free; |
| } |
| |
| if (!strcmp(buf, "0")) { |
| margining->lanes = 0; |
| } else if (!strcmp(buf, "1")) { |
| margining->lanes = 1; |
| } else if (!strcmp(buf, "all")) { |
| /* Needs to be supported */ |
| if (both_lanes(margining)) |
| margining->lanes = 7; |
| else |
| ret = -EINVAL; |
| } else { |
| ret = -EINVAL; |
| } |
| |
| mutex_unlock(&tb->lock); |
| |
| out_free: |
| free_page((unsigned long)buf); |
| return ret < 0 ? ret : count; |
| } |
| |
| static int margining_lanes_show(struct seq_file *s, void *not_used) |
| { |
| struct tb_margining *margining = s->private; |
| struct tb *tb = margining->port->sw->tb; |
| unsigned int lanes; |
| |
| if (mutex_lock_interruptible(&tb->lock)) |
| return -ERESTARTSYS; |
| |
| lanes = margining->lanes; |
| if (both_lanes(margining)) { |
| if (!lanes) |
| seq_puts(s, "[0] 1 all\n"); |
| else if (lanes == 1) |
| seq_puts(s, "0 [1] all\n"); |
| else |
| seq_puts(s, "0 1 [all]\n"); |
| } else { |
| if (!lanes) |
| seq_puts(s, "[0] 1\n"); |
| else |
| seq_puts(s, "0 [1]\n"); |
| } |
| |
| mutex_unlock(&tb->lock); |
| return 0; |
| } |
| DEBUGFS_ATTR_RW(margining_lanes); |
| |
| static ssize_t |
| margining_voltage_time_offset_write(struct file *file, |
| const char __user *user_buf, |
| size_t count, loff_t *ppos) |
| { |
| struct seq_file *s = file->private_data; |
| struct tb_margining *margining = s->private; |
| struct tb *tb = margining->port->sw->tb; |
| unsigned int max_margin; |
| unsigned int val; |
| int ret; |
| |
| ret = kstrtouint_from_user(user_buf, count, 10, &val); |
| if (ret) |
| return ret; |
| |
| scoped_cond_guard(mutex_intr, return -ERESTARTSYS, &tb->lock) { |
| if (!margining->software) |
| return -EOPNOTSUPP; |
| |
| if (margining->time) |
| max_margin = margining->time_steps; |
| else |
| if (margining->optional_voltage_offset_range) |
| max_margin = margining->voltage_steps_optional_range; |
| else |
| max_margin = margining->voltage_steps; |
| |
| margining->voltage_time_offset = clamp(val, 0, max_margin); |
| } |
| |
| return count; |
| } |
| |
| static int margining_voltage_time_offset_show(struct seq_file *s, |
| void *not_used) |
| { |
| const struct tb_margining *margining = s->private; |
| struct tb *tb = margining->port->sw->tb; |
| |
| scoped_cond_guard(mutex_intr, return -ERESTARTSYS, &tb->lock) { |
| if (!margining->software) |
| return -EOPNOTSUPP; |
| |
| seq_printf(s, "%d\n", margining->voltage_time_offset); |
| } |
| |
| return 0; |
| } |
| DEBUGFS_ATTR_RW(margining_voltage_time_offset); |
| |
| static ssize_t |
| margining_error_counter_write(struct file *file, const char __user *user_buf, |
| size_t count, loff_t *ppos) |
| { |
| enum usb4_margin_sw_error_counter error_counter; |
| struct seq_file *s = file->private_data; |
| struct tb_margining *margining = s->private; |
| struct tb *tb = margining->port->sw->tb; |
| char *buf; |
| |
| buf = validate_and_copy_from_user(user_buf, &count); |
| if (IS_ERR(buf)) |
| return PTR_ERR(buf); |
| |
| buf[count - 1] = '\0'; |
| |
| if (!strcmp(buf, "nop")) |
| error_counter = USB4_MARGIN_SW_ERROR_COUNTER_NOP; |
| else if (!strcmp(buf, "clear")) |
| error_counter = USB4_MARGIN_SW_ERROR_COUNTER_CLEAR; |
| else if (!strcmp(buf, "start")) |
| error_counter = USB4_MARGIN_SW_ERROR_COUNTER_START; |
| else if (!strcmp(buf, "stop")) |
| error_counter = USB4_MARGIN_SW_ERROR_COUNTER_STOP; |
| else |
| return -EINVAL; |
| |
| scoped_cond_guard(mutex_intr, return -ERESTARTSYS, &tb->lock) { |
| if (!margining->software) |
| return -EOPNOTSUPP; |
| |
| margining->error_counter = error_counter; |
| } |
| |
| return count; |
| } |
| |
| static int margining_error_counter_show(struct seq_file *s, void *not_used) |
| { |
| const struct tb_margining *margining = s->private; |
| struct tb *tb = margining->port->sw->tb; |
| |
| scoped_cond_guard(mutex_intr, return -ERESTARTSYS, &tb->lock) { |
| if (!margining->software) |
| return -EOPNOTSUPP; |
| |
| switch (margining->error_counter) { |
| case USB4_MARGIN_SW_ERROR_COUNTER_NOP: |
| seq_puts(s, "[nop] clear start stop\n"); |
| break; |
| case USB4_MARGIN_SW_ERROR_COUNTER_CLEAR: |
| seq_puts(s, "nop [clear] start stop\n"); |
| break; |
| case USB4_MARGIN_SW_ERROR_COUNTER_START: |
| seq_puts(s, "nop clear [start] stop\n"); |
| break; |
| case USB4_MARGIN_SW_ERROR_COUNTER_STOP: |
| seq_puts(s, "nop clear start [stop]\n"); |
| break; |
| } |
| } |
| |
| return 0; |
| } |
| DEBUGFS_ATTR_RW(margining_error_counter); |
| |
| static ssize_t |
| margining_dwell_time_write(struct file *file, const char __user *user_buf, |
| size_t count, loff_t *ppos) |
| { |
| struct seq_file *s = file->private_data; |
| struct tb_margining *margining = s->private; |
| struct tb *tb = margining->port->sw->tb; |
| unsigned int val; |
| int ret; |
| |
| ret = kstrtouint_from_user(user_buf, count, 10, &val); |
| if (ret) |
| return ret; |
| |
| scoped_cond_guard(mutex_intr, return -ERESTARTSYS, &tb->lock) { |
| if (!margining->software) |
| return -EOPNOTSUPP; |
| |
| margining->dwell_time = clamp(val, MIN_DWELL_TIME, MAX_DWELL_TIME); |
| } |
| |
| return count; |
| } |
| |
| static int margining_dwell_time_show(struct seq_file *s, void *not_used) |
| { |
| struct tb_margining *margining = s->private; |
| struct tb *tb = margining->port->sw->tb; |
| |
| scoped_cond_guard(mutex_intr, return -ERESTARTSYS, &tb->lock) { |
| if (!margining->software) |
| return -EOPNOTSUPP; |
| |
| seq_printf(s, "%d\n", margining->dwell_time); |
| } |
| |
| return 0; |
| } |
| DEBUGFS_ATTR_RW(margining_dwell_time); |
| |
| static ssize_t |
| margining_optional_voltage_offset_write(struct file *file, const char __user *user_buf, |
| size_t count, loff_t *ppos) |
| { |
| struct seq_file *s = file->private_data; |
| struct tb_margining *margining = s->private; |
| struct tb *tb = margining->port->sw->tb; |
| bool val; |
| int ret; |
| |
| ret = kstrtobool_from_user(user_buf, count, &val); |
| if (ret) |
| return ret; |
| |
| scoped_cond_guard(mutex_intr, return -ERESTARTSYS, &tb->lock) { |
| margining->optional_voltage_offset_range = val; |
| } |
| |
| return count; |
| } |
| |
| static int margining_optional_voltage_offset_show(struct seq_file *s, |
| void *not_used) |
| { |
| struct tb_margining *margining = s->private; |
| struct tb *tb = margining->port->sw->tb; |
| |
| scoped_cond_guard(mutex_intr, return -ERESTARTSYS, &tb->lock) { |
| seq_printf(s, "%u\n", margining->optional_voltage_offset_range); |
| } |
| |
| return 0; |
| } |
| DEBUGFS_ATTR_RW(margining_optional_voltage_offset); |
| |
| static ssize_t margining_mode_write(struct file *file, |
| const char __user *user_buf, |
| size_t count, loff_t *ppos) |
| { |
| struct seq_file *s = file->private_data; |
| struct tb_margining *margining = s->private; |
| struct tb *tb = margining->port->sw->tb; |
| int ret = 0; |
| char *buf; |
| |
| buf = validate_and_copy_from_user(user_buf, &count); |
| if (IS_ERR(buf)) |
| return PTR_ERR(buf); |
| |
| buf[count - 1] = '\0'; |
| |
| if (mutex_lock_interruptible(&tb->lock)) { |
| ret = -ERESTARTSYS; |
| goto out_free; |
| } |
| |
| if (!strcmp(buf, "software")) { |
| if (supports_software(margining)) |
| margining->software = true; |
| else |
| ret = -EINVAL; |
| } else if (!strcmp(buf, "hardware")) { |
| if (supports_hardware(margining)) |
| margining->software = false; |
| else |
| ret = -EINVAL; |
| } else { |
| ret = -EINVAL; |
| } |
| |
| mutex_unlock(&tb->lock); |
| |
| out_free: |
| free_page((unsigned long)buf); |
| return ret ? ret : count; |
| } |
| |
| static int margining_mode_show(struct seq_file *s, void *not_used) |
| { |
| struct tb_margining *margining = s->private; |
| struct tb *tb = margining->port->sw->tb; |
| const char *space = ""; |
| |
| if (mutex_lock_interruptible(&tb->lock)) |
| return -ERESTARTSYS; |
| |
| if (supports_software(margining)) { |
| if (margining->software) |
| seq_puts(s, "[software]"); |
| else |
| seq_puts(s, "software"); |
| space = " "; |
| } |
| if (supports_hardware(margining)) { |
| if (margining->software) |
| seq_printf(s, "%shardware", space); |
| else |
| seq_printf(s, "%s[hardware]", space); |
| } |
| |
| mutex_unlock(&tb->lock); |
| |
| seq_puts(s, "\n"); |
| return 0; |
| } |
| DEBUGFS_ATTR_RW(margining_mode); |
| |
| static int margining_run_sw(struct tb_margining *margining, |
| struct usb4_port_margining_params *params) |
| { |
| u32 nsamples = margining->dwell_time / DWELL_SAMPLE_INTERVAL; |
| int ret, i; |
| |
| ret = usb4_port_sw_margin(margining->port, margining->target, margining->index, |
| params, margining->results); |
| if (ret) |
| goto out_stop; |
| |
| for (i = 0; i <= nsamples; i++) { |
| u32 errors = 0; |
| |
| ret = usb4_port_sw_margin_errors(margining->port, margining->target, |
| margining->index, &margining->results[1]); |
| if (ret) |
| break; |
| |
| if (margining->lanes == USB4_MARGIN_SW_LANE_0) |
| errors = FIELD_GET(USB4_MARGIN_SW_ERR_COUNTER_LANE_0_MASK, |
| margining->results[1]); |
| else if (margining->lanes == USB4_MARGIN_SW_LANE_1) |
| errors = FIELD_GET(USB4_MARGIN_SW_ERR_COUNTER_LANE_1_MASK, |
| margining->results[1]); |
| else if (margining->lanes == USB4_MARGIN_SW_ALL_LANES) |
| errors = margining->results[1]; |
| |
| /* Any errors stop the test */ |
| if (errors) |
| break; |
| |
| fsleep(DWELL_SAMPLE_INTERVAL * USEC_PER_MSEC); |
| } |
| |
| out_stop: |
| /* |
| * Stop the counters but don't clear them to allow the |
| * different error counter configurations. |
| */ |
| margining_modify_error_counter(margining, margining->lanes, |
| USB4_MARGIN_SW_ERROR_COUNTER_STOP); |
| return ret; |
| } |
| |
| static int margining_run_write(void *data, u64 val) |
| { |
| struct tb_margining *margining = data; |
| struct tb_port *port = margining->port; |
| struct device *dev = margining->dev; |
| struct tb_switch *sw = port->sw; |
| struct tb_switch *down_sw; |
| struct tb *tb = sw->tb; |
| int ret, clx; |
| |
| if (val != 1) |
| return -EINVAL; |
| |
| pm_runtime_get_sync(dev); |
| |
| if (mutex_lock_interruptible(&tb->lock)) { |
| ret = -ERESTARTSYS; |
| goto out_rpm_put; |
| } |
| |
| if (tb_is_upstream_port(port)) |
| down_sw = sw; |
| else if (port->remote) |
| down_sw = port->remote->sw; |
| else |
| down_sw = NULL; |
| |
| if (down_sw) { |
| /* |
| * CL states may interfere with lane margining so |
| * disable them temporarily now. |
| */ |
| ret = tb_switch_clx_disable(down_sw); |
| if (ret < 0) { |
| tb_sw_warn(down_sw, "failed to disable CL states\n"); |
| goto out_unlock; |
| } |
| clx = ret; |
| } |
| |
| /* Clear the results */ |
| memset(margining->results, 0, sizeof(margining->results)); |
| |
| if (margining->software) { |
| struct usb4_port_margining_params params = { |
| .error_counter = USB4_MARGIN_SW_ERROR_COUNTER_CLEAR, |
| .lanes = margining->lanes, |
| .time = margining->time, |
| .voltage_time_offset = margining->voltage_time_offset, |
| .right_high = margining->right_high, |
| .optional_voltage_offset_range = margining->optional_voltage_offset_range, |
| }; |
| |
| tb_port_dbg(port, |
| "running software %s lane margining for %s lanes %u\n", |
| margining->time ? "time" : "voltage", dev_name(dev), |
| margining->lanes); |
| |
| ret = margining_run_sw(margining, ¶ms); |
| } else { |
| struct usb4_port_margining_params params = { |
| .ber_level = margining->ber_level, |
| .lanes = margining->lanes, |
| .time = margining->time, |
| .right_high = margining->right_high, |
| .optional_voltage_offset_range = margining->optional_voltage_offset_range, |
| }; |
| |
| tb_port_dbg(port, |
| "running hardware %s lane margining for %s lanes %u\n", |
| margining->time ? "time" : "voltage", dev_name(dev), |
| margining->lanes); |
| |
| ret = usb4_port_hw_margin(port, margining->target, margining->index, ¶ms, |
| margining->results); |
| } |
| |
| if (down_sw) |
| tb_switch_clx_enable(down_sw, clx); |
| out_unlock: |
| mutex_unlock(&tb->lock); |
| out_rpm_put: |
| pm_runtime_mark_last_busy(dev); |
| pm_runtime_put_autosuspend(dev); |
| |
| return ret; |
| } |
| DEFINE_DEBUGFS_ATTRIBUTE(margining_run_fops, NULL, margining_run_write, |
| "%llu\n"); |
| |
| static ssize_t margining_results_write(struct file *file, |
| const char __user *user_buf, |
| size_t count, loff_t *ppos) |
| { |
| struct seq_file *s = file->private_data; |
| struct tb_margining *margining = s->private; |
| struct tb *tb = margining->port->sw->tb; |
| |
| if (mutex_lock_interruptible(&tb->lock)) |
| return -ERESTARTSYS; |
| |
| /* Just clear the results */ |
| margining->results[0] = 0; |
| margining->results[1] = 0; |
| |
| if (margining->software) { |
| /* Clear the error counters */ |
| margining_modify_error_counter(margining, |
| USB4_MARGIN_SW_ALL_LANES, |
| USB4_MARGIN_SW_ERROR_COUNTER_CLEAR); |
| } |
| |
| mutex_unlock(&tb->lock); |
| return count; |
| } |
| |
| static void voltage_margin_show(struct seq_file *s, |
| const struct tb_margining *margining, u8 val) |
| { |
| unsigned int tmp, voltage; |
| |
| tmp = FIELD_GET(USB4_MARGIN_HW_RES_1_MARGIN_MASK, val); |
| voltage = tmp * margining->max_voltage_offset / margining->voltage_steps; |
| seq_printf(s, "%u mV (%u)", voltage, tmp); |
| if (val & USB4_MARGIN_HW_RES_1_EXCEEDS) |
| seq_puts(s, " exceeds maximum"); |
| seq_puts(s, "\n"); |
| if (margining->optional_voltage_offset_range) |
| seq_puts(s, " optional voltage offset range enabled\n"); |
| } |
| |
| static void time_margin_show(struct seq_file *s, |
| const struct tb_margining *margining, u8 val) |
| { |
| unsigned int tmp, interval; |
| |
| tmp = FIELD_GET(USB4_MARGIN_HW_RES_1_MARGIN_MASK, val); |
| interval = tmp * margining->max_time_offset / margining->time_steps; |
| seq_printf(s, "%u mUI (%u)", interval, tmp); |
| if (val & USB4_MARGIN_HW_RES_1_EXCEEDS) |
| seq_puts(s, " exceeds maximum"); |
| seq_puts(s, "\n"); |
| } |
| |
| static int margining_results_show(struct seq_file *s, void *not_used) |
| { |
| struct tb_margining *margining = s->private; |
| struct tb *tb = margining->port->sw->tb; |
| |
| if (mutex_lock_interruptible(&tb->lock)) |
| return -ERESTARTSYS; |
| |
| /* Dump the raw results first */ |
| seq_printf(s, "0x%08x\n", margining->results[0]); |
| /* Only the hardware margining has two result dwords */ |
| if (!margining->software) { |
| unsigned int val; |
| |
| seq_printf(s, "0x%08x\n", margining->results[1]); |
| |
| if (margining->time) { |
| if (!margining->lanes || margining->lanes == 7) { |
| val = margining->results[1]; |
| seq_puts(s, "# lane 0 right time margin: "); |
| time_margin_show(s, margining, val); |
| val = margining->results[1] >> |
| USB4_MARGIN_HW_RES_1_L0_LL_MARGIN_SHIFT; |
| seq_puts(s, "# lane 0 left time margin: "); |
| time_margin_show(s, margining, val); |
| } |
| if (margining->lanes == 1 || margining->lanes == 7) { |
| val = margining->results[1] >> |
| USB4_MARGIN_HW_RES_1_L1_RH_MARGIN_SHIFT; |
| seq_puts(s, "# lane 1 right time margin: "); |
| time_margin_show(s, margining, val); |
| val = margining->results[1] >> |
| USB4_MARGIN_HW_RES_1_L1_LL_MARGIN_SHIFT; |
| seq_puts(s, "# lane 1 left time margin: "); |
| time_margin_show(s, margining, val); |
| } |
| } else { |
| if (!margining->lanes || margining->lanes == 7) { |
| val = margining->results[1]; |
| seq_puts(s, "# lane 0 high voltage margin: "); |
| voltage_margin_show(s, margining, val); |
| val = margining->results[1] >> |
| USB4_MARGIN_HW_RES_1_L0_LL_MARGIN_SHIFT; |
| seq_puts(s, "# lane 0 low voltage margin: "); |
| voltage_margin_show(s, margining, val); |
| } |
| if (margining->lanes == 1 || margining->lanes == 7) { |
| val = margining->results[1] >> |
| USB4_MARGIN_HW_RES_1_L1_RH_MARGIN_SHIFT; |
| seq_puts(s, "# lane 1 high voltage margin: "); |
| voltage_margin_show(s, margining, val); |
| val = margining->results[1] >> |
| USB4_MARGIN_HW_RES_1_L1_LL_MARGIN_SHIFT; |
| seq_puts(s, "# lane 1 low voltage margin: "); |
| voltage_margin_show(s, margining, val); |
| } |
| } |
| } else { |
| u32 lane_errors, result; |
| |
| seq_printf(s, "0x%08x\n", margining->results[1]); |
| result = FIELD_GET(USB4_MARGIN_SW_LANES_MASK, margining->results[0]); |
| |
| if (result == USB4_MARGIN_SW_LANE_0 || |
| result == USB4_MARGIN_SW_ALL_LANES) { |
| lane_errors = FIELD_GET(USB4_MARGIN_SW_ERR_COUNTER_LANE_0_MASK, |
| margining->results[1]); |
| seq_printf(s, "# lane 0 errors: %u\n", lane_errors); |
| } |
| if (result == USB4_MARGIN_SW_LANE_1 || |
| result == USB4_MARGIN_SW_ALL_LANES) { |
| lane_errors = FIELD_GET(USB4_MARGIN_SW_ERR_COUNTER_LANE_1_MASK, |
| margining->results[1]); |
| seq_printf(s, "# lane 1 errors: %u\n", lane_errors); |
| } |
| } |
| |
| mutex_unlock(&tb->lock); |
| return 0; |
| } |
| DEBUGFS_ATTR_RW(margining_results); |
| |
| static ssize_t margining_test_write(struct file *file, |
| const char __user *user_buf, |
| size_t count, loff_t *ppos) |
| { |
| struct seq_file *s = file->private_data; |
| struct tb_margining *margining = s->private; |
| struct tb *tb = margining->port->sw->tb; |
| int ret = 0; |
| char *buf; |
| |
| buf = validate_and_copy_from_user(user_buf, &count); |
| if (IS_ERR(buf)) |
| return PTR_ERR(buf); |
| |
| buf[count - 1] = '\0'; |
| |
| if (mutex_lock_interruptible(&tb->lock)) { |
| ret = -ERESTARTSYS; |
| goto out_free; |
| } |
| |
| if (!strcmp(buf, "time") && supports_time(margining)) |
| margining->time = true; |
| else if (!strcmp(buf, "voltage")) |
| margining->time = false; |
| else |
| ret = -EINVAL; |
| |
| mutex_unlock(&tb->lock); |
| |
| out_free: |
| free_page((unsigned long)buf); |
| return ret ? ret : count; |
| } |
| |
| static int margining_test_show(struct seq_file *s, void *not_used) |
| { |
| struct tb_margining *margining = s->private; |
| struct tb *tb = margining->port->sw->tb; |
| |
| if (mutex_lock_interruptible(&tb->lock)) |
| return -ERESTARTSYS; |
| |
| if (supports_time(margining)) { |
| if (margining->time) |
| seq_puts(s, "voltage [time]\n"); |
| else |
| seq_puts(s, "[voltage] time\n"); |
| } else { |
| seq_puts(s, "[voltage]\n"); |
| } |
| |
| mutex_unlock(&tb->lock); |
| return 0; |
| } |
| DEBUGFS_ATTR_RW(margining_test); |
| |
| static ssize_t margining_margin_write(struct file *file, |
| const char __user *user_buf, |
| size_t count, loff_t *ppos) |
| { |
| struct seq_file *s = file->private_data; |
| struct tb_margining *margining = s->private; |
| struct tb *tb = margining->port->sw->tb; |
| int ret = 0; |
| char *buf; |
| |
| buf = validate_and_copy_from_user(user_buf, &count); |
| if (IS_ERR(buf)) |
| return PTR_ERR(buf); |
| |
| buf[count - 1] = '\0'; |
| |
| if (mutex_lock_interruptible(&tb->lock)) { |
| ret = -ERESTARTSYS; |
| goto out_free; |
| } |
| |
| if (margining->time) { |
| if (!strcmp(buf, "left")) |
| margining->right_high = false; |
| else if (!strcmp(buf, "right")) |
| margining->right_high = true; |
| else |
| ret = -EINVAL; |
| } else { |
| if (!strcmp(buf, "low")) |
| margining->right_high = false; |
| else if (!strcmp(buf, "high")) |
| margining->right_high = true; |
| else |
| ret = -EINVAL; |
| } |
| |
| mutex_unlock(&tb->lock); |
| |
| out_free: |
| free_page((unsigned long)buf); |
| return ret ? ret : count; |
| } |
| |
| static int margining_margin_show(struct seq_file *s, void *not_used) |
| { |
| struct tb_margining *margining = s->private; |
| struct tb *tb = margining->port->sw->tb; |
| |
| if (mutex_lock_interruptible(&tb->lock)) |
| return -ERESTARTSYS; |
| |
| if (margining->time) { |
| if (margining->right_high) |
| seq_puts(s, "left [right]\n"); |
| else |
| seq_puts(s, "[left] right\n"); |
| } else { |
| if (margining->right_high) |
| seq_puts(s, "low [high]\n"); |
| else |
| seq_puts(s, "[low] high\n"); |
| } |
| |
| mutex_unlock(&tb->lock); |
| return 0; |
| } |
| DEBUGFS_ATTR_RW(margining_margin); |
| |
| static struct tb_margining *margining_alloc(struct tb_port *port, |
| struct device *dev, |
| enum usb4_sb_target target, |
| u8 index, struct dentry *parent) |
| { |
| struct tb_margining *margining; |
| struct dentry *dir; |
| unsigned int val; |
| int ret; |
| |
| margining = kzalloc(sizeof(*margining), GFP_KERNEL); |
| if (!margining) |
| return NULL; |
| |
| margining->port = port; |
| margining->target = target; |
| margining->index = index; |
| margining->dev = dev; |
| |
| ret = usb4_port_margining_caps(port, target, index, margining->caps); |
| if (ret) { |
| kfree(margining); |
| return NULL; |
| } |
| |
| /* Set the initial mode */ |
| if (supports_software(margining)) |
| margining->software = true; |
| |
| val = FIELD_GET(USB4_MARGIN_CAP_0_VOLTAGE_STEPS_MASK, margining->caps[0]); |
| margining->voltage_steps = val; |
| val = FIELD_GET(USB4_MARGIN_CAP_0_MAX_VOLTAGE_OFFSET_MASK, margining->caps[0]); |
| margining->max_voltage_offset = 74 + val * 2; |
| |
| if (supports_optional_voltage_offset_range(margining)) { |
| val = FIELD_GET(USB4_MARGIN_CAP_0_VOLT_STEPS_OPT_MASK, |
| margining->caps[0]); |
| margining->voltage_steps_optional_range = val; |
| val = FIELD_GET(USB4_MARGIN_CAP_1_MAX_VOLT_OFS_OPT_MASK, |
| margining->caps[1]); |
| margining->max_voltage_offset_optional_range = 74 + val * 2; |
| } |
| |
| if (supports_time(margining)) { |
| val = FIELD_GET(USB4_MARGIN_CAP_1_TIME_STEPS_MASK, margining->caps[1]); |
| margining->time_steps = val; |
| val = FIELD_GET(USB4_MARGIN_CAP_1_TIME_OFFSET_MASK, margining->caps[1]); |
| /* |
| * Store it as mUI (milli Unit Interval) because we want |
| * to keep it as integer. |
| */ |
| margining->max_time_offset = 200 + 10 * val; |
| } |
| |
| dir = debugfs_create_dir("margining", parent); |
| if (supports_hardware(margining)) { |
| val = FIELD_GET(USB4_MARGIN_CAP_1_MIN_BER_MASK, margining->caps[1]); |
| margining->min_ber_level = val; |
| val = FIELD_GET(USB4_MARGIN_CAP_1_MAX_BER_MASK, margining->caps[1]); |
| margining->max_ber_level = val; |
| |
| /* Set the default to minimum */ |
| margining->ber_level = margining->min_ber_level; |
| |
| debugfs_create_file("ber_level_contour", 0400, dir, margining, |
| &margining_ber_level_fops); |
| } |
| debugfs_create_file("caps", 0400, dir, margining, &margining_caps_fops); |
| debugfs_create_file("lanes", 0600, dir, margining, &margining_lanes_fops); |
| debugfs_create_file("mode", 0600, dir, margining, &margining_mode_fops); |
| debugfs_create_file("run", 0600, dir, margining, &margining_run_fops); |
| debugfs_create_file("results", 0600, dir, margining, |
| &margining_results_fops); |
| debugfs_create_file("test", 0600, dir, margining, &margining_test_fops); |
| if (independent_voltage_margins(margining) == USB4_MARGIN_CAP_0_VOLTAGE_HL || |
| (supports_time(margining) && |
| independent_time_margins(margining) == USB4_MARGIN_CAP_1_TIME_LR)) |
| debugfs_create_file("margin", 0600, dir, margining, |
| &margining_margin_fops); |
| |
| margining->error_counter = USB4_MARGIN_SW_ERROR_COUNTER_CLEAR; |
| margining->dwell_time = MIN_DWELL_TIME; |
| |
| if (supports_optional_voltage_offset_range(margining)) |
| debugfs_create_file("optional_voltage_offset", DEBUGFS_MODE, dir, margining, |
| &margining_optional_voltage_offset_fops); |
| |
| if (supports_software(margining)) { |
| debugfs_create_file("voltage_time_offset", DEBUGFS_MODE, dir, margining, |
| &margining_voltage_time_offset_fops); |
| debugfs_create_file("error_counter", DEBUGFS_MODE, dir, margining, |
| &margining_error_counter_fops); |
| debugfs_create_file("dwell_time", DEBUGFS_MODE, dir, margining, |
| &margining_dwell_time_fops); |
| } |
| return margining; |
| } |
| |
| static void margining_port_init(struct tb_port *port) |
| { |
| struct dentry *parent; |
| char dir_name[10]; |
| |
| if (!port->usb4) |
| return; |
| |
| snprintf(dir_name, sizeof(dir_name), "port%d", port->port); |
| parent = debugfs_lookup(dir_name, port->sw->debugfs_dir); |
| port->usb4->margining = margining_alloc(port, &port->usb4->dev, |
| USB4_SB_TARGET_ROUTER, 0, |
| parent); |
| } |
| |
| static void margining_port_remove(struct tb_port *port) |
| { |
| struct dentry *parent; |
| char dir_name[10]; |
| |
| if (!port->usb4) |
| return; |
| |
| snprintf(dir_name, sizeof(dir_name), "port%d", port->port); |
| parent = debugfs_lookup(dir_name, port->sw->debugfs_dir); |
| if (parent) |
| debugfs_lookup_and_remove("margining", parent); |
| |
| kfree(port->usb4->margining); |
| port->usb4->margining = NULL; |
| } |
| |
| static void margining_switch_init(struct tb_switch *sw) |
| { |
| struct tb_port *upstream, *downstream; |
| struct tb_switch *parent_sw; |
| u64 route = tb_route(sw); |
| |
| if (!route) |
| return; |
| |
| upstream = tb_upstream_port(sw); |
| parent_sw = tb_switch_parent(sw); |
| downstream = tb_port_at(route, parent_sw); |
| |
| margining_port_init(downstream); |
| margining_port_init(upstream); |
| } |
| |
| static void margining_switch_remove(struct tb_switch *sw) |
| { |
| struct tb_port *upstream, *downstream; |
| struct tb_switch *parent_sw; |
| u64 route = tb_route(sw); |
| |
| if (!route) |
| return; |
| |
| upstream = tb_upstream_port(sw); |
| parent_sw = tb_switch_parent(sw); |
| downstream = tb_port_at(route, parent_sw); |
| |
| margining_port_remove(upstream); |
| margining_port_remove(downstream); |
| } |
| |
| static void margining_xdomain_init(struct tb_xdomain *xd) |
| { |
| struct tb_switch *parent_sw; |
| struct tb_port *downstream; |
| |
| parent_sw = tb_xdomain_parent(xd); |
| downstream = tb_port_at(xd->route, parent_sw); |
| |
| margining_port_init(downstream); |
| } |
| |
| static void margining_xdomain_remove(struct tb_xdomain *xd) |
| { |
| struct tb_switch *parent_sw; |
| struct tb_port *downstream; |
| |
| parent_sw = tb_xdomain_parent(xd); |
| downstream = tb_port_at(xd->route, parent_sw); |
| margining_port_remove(downstream); |
| } |
| |
| static void margining_retimer_init(struct tb_retimer *rt, struct dentry *debugfs_dir) |
| { |
| rt->margining = margining_alloc(rt->port, &rt->dev, |
| USB4_SB_TARGET_RETIMER, rt->index, |
| debugfs_dir); |
| } |
| |
| static void margining_retimer_remove(struct tb_retimer *rt) |
| { |
| kfree(rt->margining); |
| rt->margining = NULL; |
| } |
| #else |
| static inline void margining_switch_init(struct tb_switch *sw) { } |
| static inline void margining_switch_remove(struct tb_switch *sw) { } |
| static inline void margining_xdomain_init(struct tb_xdomain *xd) { } |
| static inline void margining_xdomain_remove(struct tb_xdomain *xd) { } |
| static inline void margining_retimer_init(struct tb_retimer *rt, |
| struct dentry *debugfs_dir) { } |
| static inline void margining_retimer_remove(struct tb_retimer *rt) { } |
| #endif |
| |
| static int port_clear_all_counters(struct tb_port *port) |
| { |
| u32 *buf; |
| int ret; |
| |
| buf = kcalloc(COUNTER_SET_LEN * port->config.max_counters, sizeof(u32), |
| GFP_KERNEL); |
| if (!buf) |
| return -ENOMEM; |
| |
| ret = tb_port_write(port, buf, TB_CFG_COUNTERS, 0, |
| COUNTER_SET_LEN * port->config.max_counters); |
| kfree(buf); |
| |
| return ret; |
| } |
| |
| static ssize_t counters_write(struct file *file, const char __user *user_buf, |
| size_t count, loff_t *ppos) |
| { |
| struct seq_file *s = file->private_data; |
| struct tb_port *port = s->private; |
| struct tb_switch *sw = port->sw; |
| struct tb *tb = port->sw->tb; |
| char *buf; |
| int ret; |
| |
| buf = validate_and_copy_from_user(user_buf, &count); |
| if (IS_ERR(buf)) |
| return PTR_ERR(buf); |
| |
| pm_runtime_get_sync(&sw->dev); |
| |
| if (mutex_lock_interruptible(&tb->lock)) { |
| ret = -ERESTARTSYS; |
| goto out; |
| } |
| |
| /* If written delimiter only, clear all counters in one shot */ |
| if (buf[0] == '\n') { |
| ret = port_clear_all_counters(port); |
| } else { |
| char *line = buf; |
| u32 val, offset; |
| |
| ret = -EINVAL; |
| while (parse_line(&line, &offset, &val, 1, 4)) { |
| ret = tb_port_write(port, &val, TB_CFG_COUNTERS, |
| offset, 1); |
| if (ret) |
| break; |
| } |
| } |
| |
| mutex_unlock(&tb->lock); |
| |
| out: |
| pm_runtime_mark_last_busy(&sw->dev); |
| pm_runtime_put_autosuspend(&sw->dev); |
| free_page((unsigned long)buf); |
| |
| return ret < 0 ? ret : count; |
| } |
| |
| static void cap_show_by_dw(struct seq_file *s, struct tb_switch *sw, |
| struct tb_port *port, unsigned int cap, |
| unsigned int offset, u8 cap_id, u8 vsec_id, |
| int dwords) |
| { |
| int i, ret; |
| u32 data; |
| |
| for (i = 0; i < dwords; i++) { |
| if (port) |
| ret = tb_port_read(port, &data, TB_CFG_PORT, cap + offset + i, 1); |
| else |
| ret = tb_sw_read(sw, &data, TB_CFG_SWITCH, cap + offset + i, 1); |
| if (ret) { |
| seq_printf(s, "0x%04x <not accessible>\n", cap + offset + i); |
| continue; |
| } |
| |
| seq_printf(s, "0x%04x %4d 0x%02x 0x%02x 0x%08x\n", cap + offset + i, |
| offset + i, cap_id, vsec_id, data); |
| } |
| } |
| |
| static void cap_show(struct seq_file *s, struct tb_switch *sw, |
| struct tb_port *port, unsigned int cap, u8 cap_id, |
| u8 vsec_id, int length) |
| { |
| int ret, offset = 0; |
| |
| while (length > 0) { |
| int i, dwords = min(length, TB_MAX_CONFIG_RW_LENGTH); |
| u32 data[TB_MAX_CONFIG_RW_LENGTH]; |
| |
| if (port) |
| ret = tb_port_read(port, data, TB_CFG_PORT, cap + offset, |
| dwords); |
| else |
| ret = tb_sw_read(sw, data, TB_CFG_SWITCH, cap + offset, dwords); |
| if (ret) { |
| cap_show_by_dw(s, sw, port, cap, offset, cap_id, vsec_id, length); |
| return; |
| } |
| |
| for (i = 0; i < dwords; i++) { |
| seq_printf(s, "0x%04x %4d 0x%02x 0x%02x 0x%08x\n", |
| cap + offset + i, offset + i, |
| cap_id, vsec_id, data[i]); |
| } |
| |
| length -= dwords; |
| offset += dwords; |
| } |
| } |
| |
| static void port_cap_show(struct tb_port *port, struct seq_file *s, |
| unsigned int cap) |
| { |
| struct tb_cap_any header; |
| u8 vsec_id = 0; |
| size_t length; |
| int ret; |
| |
| ret = tb_port_read(port, &header, TB_CFG_PORT, cap, 1); |
| if (ret) { |
| seq_printf(s, "0x%04x <capability read failed>\n", cap); |
| return; |
| } |
| |
| switch (header.basic.cap) { |
| case TB_PORT_CAP_PHY: |
| length = PORT_CAP_LANE_LEN; |
| break; |
| |
| case TB_PORT_CAP_TIME1: |
| if (usb4_switch_version(port->sw) < 2) |
| length = PORT_CAP_TMU_V1_LEN; |
| else |
| length = PORT_CAP_TMU_V2_LEN; |
| break; |
| |
| case TB_PORT_CAP_POWER: |
| length = PORT_CAP_POWER_LEN; |
| break; |
| |
| case TB_PORT_CAP_ADAP: |
| if (tb_port_is_pcie_down(port) || tb_port_is_pcie_up(port)) { |
| if (usb4_switch_version(port->sw) < 2) |
| length = PORT_CAP_V1_PCIE_LEN; |
| else |
| length = PORT_CAP_V2_PCIE_LEN; |
| } else if (tb_port_is_dpin(port)) { |
| if (usb4_switch_version(port->sw) < 2) |
| length = PORT_CAP_DP_V1_LEN; |
| else |
| length = PORT_CAP_DP_V2_LEN; |
| } else if (tb_port_is_dpout(port)) { |
| length = PORT_CAP_DP_V1_LEN; |
| } else if (tb_port_is_usb3_down(port) || |
| tb_port_is_usb3_up(port)) { |
| length = PORT_CAP_USB3_LEN; |
| } else { |
| seq_printf(s, "0x%04x <unsupported capability 0x%02x>\n", |
| cap, header.basic.cap); |
| return; |
| } |
| break; |
| |
| case TB_PORT_CAP_VSE: |
| if (!header.extended_short.length) { |
| ret = tb_port_read(port, (u32 *)&header + 1, TB_CFG_PORT, |
| cap + 1, 1); |
| if (ret) { |
| seq_printf(s, "0x%04x <capability read failed>\n", |
| cap + 1); |
| return; |
| } |
| length = header.extended_long.length; |
| vsec_id = header.extended_short.vsec_id; |
| } else { |
| length = header.extended_short.length; |
| vsec_id = header.extended_short.vsec_id; |
| } |
| break; |
| |
| case TB_PORT_CAP_USB4: |
| length = PORT_CAP_USB4_LEN; |
| break; |
| |
| default: |
| seq_printf(s, "0x%04x <unsupported capability 0x%02x>\n", |
| cap, header.basic.cap); |
| return; |
| } |
| |
| cap_show(s, NULL, port, cap, header.basic.cap, vsec_id, length); |
| } |
| |
| static void port_caps_show(struct tb_port *port, struct seq_file *s) |
| { |
| int cap; |
| |
| cap = tb_port_next_cap(port, 0); |
| while (cap > 0) { |
| port_cap_show(port, s, cap); |
| cap = tb_port_next_cap(port, cap); |
| } |
| } |
| |
| static int port_basic_regs_show(struct tb_port *port, struct seq_file *s) |
| { |
| u32 data[PORT_CAP_BASIC_LEN]; |
| int ret, i; |
| |
| ret = tb_port_read(port, data, TB_CFG_PORT, 0, ARRAY_SIZE(data)); |
| if (ret) |
| return ret; |
| |
| for (i = 0; i < ARRAY_SIZE(data); i++) |
| seq_printf(s, "0x%04x %4d 0x00 0x00 0x%08x\n", i, i, data[i]); |
| |
| return 0; |
| } |
| |
| static int port_regs_show(struct seq_file *s, void *not_used) |
| { |
| struct tb_port *port = s->private; |
| struct tb_switch *sw = port->sw; |
| struct tb *tb = sw->tb; |
| int ret; |
| |
| pm_runtime_get_sync(&sw->dev); |
| |
| if (mutex_lock_interruptible(&tb->lock)) { |
| ret = -ERESTARTSYS; |
| goto out_rpm_put; |
| } |
| |
| seq_puts(s, "# offset relative_offset cap_id vs_cap_id value\n"); |
| |
| ret = port_basic_regs_show(port, s); |
| if (ret) |
| goto out_unlock; |
| |
| port_caps_show(port, s); |
| |
| out_unlock: |
| mutex_unlock(&tb->lock); |
| out_rpm_put: |
| pm_runtime_mark_last_busy(&sw->dev); |
| pm_runtime_put_autosuspend(&sw->dev); |
| |
| return ret; |
| } |
| DEBUGFS_ATTR_RW(port_regs); |
| |
| static void switch_cap_show(struct tb_switch *sw, struct seq_file *s, |
| unsigned int cap) |
| { |
| struct tb_cap_any header; |
| int ret, length; |
| u8 vsec_id = 0; |
| |
| ret = tb_sw_read(sw, &header, TB_CFG_SWITCH, cap, 1); |
| if (ret) { |
| seq_printf(s, "0x%04x <capability read failed>\n", cap); |
| return; |
| } |
| |
| if (header.basic.cap == TB_SWITCH_CAP_VSE) { |
| if (!header.extended_short.length) { |
| ret = tb_sw_read(sw, (u32 *)&header + 1, TB_CFG_SWITCH, |
| cap + 1, 1); |
| if (ret) { |
| seq_printf(s, "0x%04x <capability read failed>\n", |
| cap + 1); |
| return; |
| } |
| length = header.extended_long.length; |
| } else { |
| length = header.extended_short.length; |
| } |
| vsec_id = header.extended_short.vsec_id; |
| } else { |
| if (header.basic.cap == TB_SWITCH_CAP_TMU) { |
| length = SWITCH_CAP_TMU_LEN; |
| } else { |
| seq_printf(s, "0x%04x <unknown capability 0x%02x>\n", |
| cap, header.basic.cap); |
| return; |
| } |
| } |
| |
| cap_show(s, sw, NULL, cap, header.basic.cap, vsec_id, length); |
| } |
| |
| static void switch_caps_show(struct tb_switch *sw, struct seq_file *s) |
| { |
| int cap; |
| |
| cap = tb_switch_next_cap(sw, 0); |
| while (cap > 0) { |
| switch_cap_show(sw, s, cap); |
| cap = tb_switch_next_cap(sw, cap); |
| } |
| } |
| |
| static int switch_basic_regs_show(struct tb_switch *sw, struct seq_file *s) |
| { |
| u32 data[SWITCH_CAP_BASIC_LEN]; |
| size_t dwords; |
| int ret, i; |
| |
| /* Only USB4 has the additional registers */ |
| if (tb_switch_is_usb4(sw)) |
| dwords = ARRAY_SIZE(data); |
| else |
| dwords = 5; |
| |
| ret = tb_sw_read(sw, data, TB_CFG_SWITCH, 0, dwords); |
| if (ret) |
| return ret; |
| |
| for (i = 0; i < dwords; i++) |
| seq_printf(s, "0x%04x %4d 0x00 0x00 0x%08x\n", i, i, data[i]); |
| |
| return 0; |
| } |
| |
| static int switch_regs_show(struct seq_file *s, void *not_used) |
| { |
| struct tb_switch *sw = s->private; |
| struct tb *tb = sw->tb; |
| int ret; |
| |
| pm_runtime_get_sync(&sw->dev); |
| |
| if (mutex_lock_interruptible(&tb->lock)) { |
| ret = -ERESTARTSYS; |
| goto out_rpm_put; |
| } |
| |
| seq_puts(s, "# offset relative_offset cap_id vs_cap_id value\n"); |
| |
| ret = switch_basic_regs_show(sw, s); |
| if (ret) |
| goto out_unlock; |
| |
| switch_caps_show(sw, s); |
| |
| out_unlock: |
| mutex_unlock(&tb->lock); |
| out_rpm_put: |
| pm_runtime_mark_last_busy(&sw->dev); |
| pm_runtime_put_autosuspend(&sw->dev); |
| |
| return ret; |
| } |
| DEBUGFS_ATTR_RW(switch_regs); |
| |
| static int path_show_one(struct tb_port *port, struct seq_file *s, int hopid) |
| { |
| u32 data[PATH_LEN]; |
| int ret, i; |
| |
| ret = tb_port_read(port, data, TB_CFG_HOPS, hopid * PATH_LEN, |
| ARRAY_SIZE(data)); |
| if (ret) { |
| seq_printf(s, "0x%04x <not accessible>\n", hopid * PATH_LEN); |
| return ret; |
| } |
| |
| for (i = 0; i < ARRAY_SIZE(data); i++) { |
| seq_printf(s, "0x%04x %4d 0x%02x 0x%08x\n", |
| hopid * PATH_LEN + i, i, hopid, data[i]); |
| } |
| |
| return 0; |
| } |
| |
| static int path_show(struct seq_file *s, void *not_used) |
| { |
| struct tb_port *port = s->private; |
| struct tb_switch *sw = port->sw; |
| struct tb *tb = sw->tb; |
| int start, i, ret = 0; |
| |
| pm_runtime_get_sync(&sw->dev); |
| |
| if (mutex_lock_interruptible(&tb->lock)) { |
| ret = -ERESTARTSYS; |
| goto out_rpm_put; |
| } |
| |
| seq_puts(s, "# offset relative_offset in_hop_id value\n"); |
| |
| /* NHI and lane adapters have entry for path 0 */ |
| if (tb_port_is_null(port) || tb_port_is_nhi(port)) { |
| ret = path_show_one(port, s, 0); |
| if (ret) |
| goto out_unlock; |
| } |
| |
| start = tb_port_is_nhi(port) ? 1 : TB_PATH_MIN_HOPID; |
| |
| for (i = start; i <= port->config.max_in_hop_id; i++) { |
| ret = path_show_one(port, s, i); |
| if (ret) |
| break; |
| } |
| |
| out_unlock: |
| mutex_unlock(&tb->lock); |
| out_rpm_put: |
| pm_runtime_mark_last_busy(&sw->dev); |
| pm_runtime_put_autosuspend(&sw->dev); |
| |
| return ret; |
| } |
| DEBUGFS_ATTR_RO(path); |
| |
| static int counter_set_regs_show(struct tb_port *port, struct seq_file *s, |
| int counter) |
| { |
| u32 data[COUNTER_SET_LEN]; |
| int ret, i; |
| |
| ret = tb_port_read(port, data, TB_CFG_COUNTERS, |
| counter * COUNTER_SET_LEN, ARRAY_SIZE(data)); |
| if (ret) { |
| seq_printf(s, "0x%04x <not accessible>\n", |
| counter * COUNTER_SET_LEN); |
| return ret; |
| } |
| |
| for (i = 0; i < ARRAY_SIZE(data); i++) { |
| seq_printf(s, "0x%04x %4d 0x%02x 0x%08x\n", |
| counter * COUNTER_SET_LEN + i, i, counter, data[i]); |
| } |
| |
| return 0; |
| } |
| |
| static int counters_show(struct seq_file *s, void *not_used) |
| { |
| struct tb_port *port = s->private; |
| struct tb_switch *sw = port->sw; |
| struct tb *tb = sw->tb; |
| int i, ret = 0; |
| |
| pm_runtime_get_sync(&sw->dev); |
| |
| if (mutex_lock_interruptible(&tb->lock)) { |
| ret = -ERESTARTSYS; |
| goto out; |
| } |
| |
| seq_puts(s, "# offset relative_offset counter_id value\n"); |
| |
| for (i = 0; i < port->config.max_counters; i++) { |
| ret = counter_set_regs_show(port, s, i); |
| if (ret) |
| break; |
| } |
| |
| mutex_unlock(&tb->lock); |
| |
| out: |
| pm_runtime_mark_last_busy(&sw->dev); |
| pm_runtime_put_autosuspend(&sw->dev); |
| |
| return ret; |
| } |
| DEBUGFS_ATTR_RW(counters); |
| |
| static int sb_regs_show(struct tb_port *port, const struct sb_reg *sb_regs, |
| size_t size, enum usb4_sb_target target, u8 index, |
| struct seq_file *s) |
| { |
| int ret, i; |
| |
| seq_puts(s, "# register value\n"); |
| |
| for (i = 0; i < size; i++) { |
| const struct sb_reg *regs = &sb_regs[i]; |
| u8 data[64]; |
| int j; |
| |
| memset(data, 0, sizeof(data)); |
| ret = usb4_port_sb_read(port, target, index, regs->reg, data, |
| regs->size); |
| if (ret) |
| return ret; |
| |
| seq_printf(s, "0x%02x", regs->reg); |
| for (j = 0; j < regs->size; j++) |
| seq_printf(s, " 0x%02x", data[j]); |
| seq_puts(s, "\n"); |
| } |
| |
| return 0; |
| } |
| |
| static int port_sb_regs_show(struct seq_file *s, void *not_used) |
| { |
| struct tb_port *port = s->private; |
| struct tb_switch *sw = port->sw; |
| struct tb *tb = sw->tb; |
| int ret; |
| |
| pm_runtime_get_sync(&sw->dev); |
| |
| if (mutex_lock_interruptible(&tb->lock)) { |
| ret = -ERESTARTSYS; |
| goto out_rpm_put; |
| } |
| |
| ret = sb_regs_show(port, port_sb_regs, ARRAY_SIZE(port_sb_regs), |
| USB4_SB_TARGET_ROUTER, 0, s); |
| |
| mutex_unlock(&tb->lock); |
| out_rpm_put: |
| pm_runtime_mark_last_busy(&sw->dev); |
| pm_runtime_put_autosuspend(&sw->dev); |
| |
| return ret; |
| } |
| DEBUGFS_ATTR_RW(port_sb_regs); |
| |
| /** |
| * tb_switch_debugfs_init() - Add debugfs entries for router |
| * @sw: Pointer to the router |
| * |
| * Adds debugfs directories and files for given router. |
| */ |
| void tb_switch_debugfs_init(struct tb_switch *sw) |
| { |
| struct dentry *debugfs_dir; |
| struct tb_port *port; |
| |
| debugfs_dir = debugfs_create_dir(dev_name(&sw->dev), tb_debugfs_root); |
| sw->debugfs_dir = debugfs_dir; |
| debugfs_create_file("regs", DEBUGFS_MODE, debugfs_dir, sw, |
| &switch_regs_fops); |
| |
| tb_switch_for_each_port(sw, port) { |
| struct dentry *debugfs_dir; |
| char dir_name[10]; |
| |
| if (port->disabled) |
| continue; |
| if (port->config.type == TB_TYPE_INACTIVE) |
| continue; |
| |
| snprintf(dir_name, sizeof(dir_name), "port%d", port->port); |
| debugfs_dir = debugfs_create_dir(dir_name, sw->debugfs_dir); |
| debugfs_create_file("regs", DEBUGFS_MODE, debugfs_dir, |
| port, &port_regs_fops); |
| debugfs_create_file("path", 0400, debugfs_dir, port, |
| &path_fops); |
| if (port->config.counters_support) |
| debugfs_create_file("counters", 0600, debugfs_dir, port, |
| &counters_fops); |
| if (port->usb4) |
| debugfs_create_file("sb_regs", DEBUGFS_MODE, debugfs_dir, |
| port, &port_sb_regs_fops); |
| } |
| |
| margining_switch_init(sw); |
| } |
| |
| /** |
| * tb_switch_debugfs_remove() - Remove all router debugfs entries |
| * @sw: Pointer to the router |
| * |
| * Removes all previously added debugfs entries under this router. |
| */ |
| void tb_switch_debugfs_remove(struct tb_switch *sw) |
| { |
| margining_switch_remove(sw); |
| debugfs_remove_recursive(sw->debugfs_dir); |
| } |
| |
| void tb_xdomain_debugfs_init(struct tb_xdomain *xd) |
| { |
| margining_xdomain_init(xd); |
| } |
| |
| void tb_xdomain_debugfs_remove(struct tb_xdomain *xd) |
| { |
| margining_xdomain_remove(xd); |
| } |
| |
| /** |
| * tb_service_debugfs_init() - Add debugfs directory for service |
| * @svc: Thunderbolt service pointer |
| * |
| * Adds debugfs directory for service. |
| */ |
| void tb_service_debugfs_init(struct tb_service *svc) |
| { |
| svc->debugfs_dir = debugfs_create_dir(dev_name(&svc->dev), |
| tb_debugfs_root); |
| } |
| |
| /** |
| * tb_service_debugfs_remove() - Remove service debugfs directory |
| * @svc: Thunderbolt service pointer |
| * |
| * Removes the previously created debugfs directory for @svc. |
| */ |
| void tb_service_debugfs_remove(struct tb_service *svc) |
| { |
| debugfs_remove_recursive(svc->debugfs_dir); |
| svc->debugfs_dir = NULL; |
| } |
| |
| static int retimer_sb_regs_show(struct seq_file *s, void *not_used) |
| { |
| struct tb_retimer *rt = s->private; |
| struct tb *tb = rt->tb; |
| int ret; |
| |
| pm_runtime_get_sync(&rt->dev); |
| |
| if (mutex_lock_interruptible(&tb->lock)) { |
| ret = -ERESTARTSYS; |
| goto out_rpm_put; |
| } |
| |
| ret = sb_regs_show(rt->port, retimer_sb_regs, ARRAY_SIZE(retimer_sb_regs), |
| USB4_SB_TARGET_RETIMER, rt->index, s); |
| |
| mutex_unlock(&tb->lock); |
| out_rpm_put: |
| pm_runtime_mark_last_busy(&rt->dev); |
| pm_runtime_put_autosuspend(&rt->dev); |
| |
| return ret; |
| } |
| DEBUGFS_ATTR_RW(retimer_sb_regs); |
| |
| /** |
| * tb_retimer_debugfs_init() - Add debugfs directory for retimer |
| * @rt: Pointer to retimer structure |
| * |
| * Adds and populates retimer debugfs directory. |
| */ |
| void tb_retimer_debugfs_init(struct tb_retimer *rt) |
| { |
| struct dentry *debugfs_dir; |
| |
| debugfs_dir = debugfs_create_dir(dev_name(&rt->dev), tb_debugfs_root); |
| debugfs_create_file("sb_regs", DEBUGFS_MODE, debugfs_dir, rt, |
| &retimer_sb_regs_fops); |
| margining_retimer_init(rt, debugfs_dir); |
| } |
| |
| /** |
| * tb_retimer_debugfs_remove() - Remove retimer debugfs directory |
| * @rt: Pointer to retimer structure |
| * |
| * Removes the retimer debugfs directory along with its contents. |
| */ |
| void tb_retimer_debugfs_remove(struct tb_retimer *rt) |
| { |
| debugfs_lookup_and_remove(dev_name(&rt->dev), tb_debugfs_root); |
| margining_retimer_remove(rt); |
| } |
| |
| void tb_debugfs_init(void) |
| { |
| tb_debugfs_root = debugfs_create_dir("thunderbolt", NULL); |
| } |
| |
| void tb_debugfs_exit(void) |
| { |
| debugfs_remove_recursive(tb_debugfs_root); |
| } |