| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Copyright (C) 2009 Felix Fietkau <nbd@nbd.name> |
| * Copyright (C) 2011-2012 Gabor Juhos <juhosg@openwrt.org> |
| * Copyright (c) 2015, 2019, The Linux Foundation. All rights reserved. |
| * Copyright (c) 2016 John Crispin <john@phrozen.org> |
| */ |
| |
| #include <linux/module.h> |
| #include <linux/phy.h> |
| #include <linux/netdevice.h> |
| #include <linux/bitfield.h> |
| #include <linux/regmap.h> |
| #include <net/dsa.h> |
| #include <linux/of_net.h> |
| #include <linux/of_mdio.h> |
| #include <linux/of_platform.h> |
| #include <linux/if_bridge.h> |
| #include <linux/mdio.h> |
| #include <linux/phylink.h> |
| #include <linux/gpio/consumer.h> |
| #include <linux/etherdevice.h> |
| |
| #include "qca8k.h" |
| |
| #define MIB_DESC(_s, _o, _n) \ |
| { \ |
| .size = (_s), \ |
| .offset = (_o), \ |
| .name = (_n), \ |
| } |
| |
| static const struct qca8k_mib_desc ar8327_mib[] = { |
| MIB_DESC(1, 0x00, "RxBroad"), |
| MIB_DESC(1, 0x04, "RxPause"), |
| MIB_DESC(1, 0x08, "RxMulti"), |
| MIB_DESC(1, 0x0c, "RxFcsErr"), |
| MIB_DESC(1, 0x10, "RxAlignErr"), |
| MIB_DESC(1, 0x14, "RxRunt"), |
| MIB_DESC(1, 0x18, "RxFragment"), |
| MIB_DESC(1, 0x1c, "Rx64Byte"), |
| MIB_DESC(1, 0x20, "Rx128Byte"), |
| MIB_DESC(1, 0x24, "Rx256Byte"), |
| MIB_DESC(1, 0x28, "Rx512Byte"), |
| MIB_DESC(1, 0x2c, "Rx1024Byte"), |
| MIB_DESC(1, 0x30, "Rx1518Byte"), |
| MIB_DESC(1, 0x34, "RxMaxByte"), |
| MIB_DESC(1, 0x38, "RxTooLong"), |
| MIB_DESC(2, 0x3c, "RxGoodByte"), |
| MIB_DESC(2, 0x44, "RxBadByte"), |
| MIB_DESC(1, 0x4c, "RxOverFlow"), |
| MIB_DESC(1, 0x50, "Filtered"), |
| MIB_DESC(1, 0x54, "TxBroad"), |
| MIB_DESC(1, 0x58, "TxPause"), |
| MIB_DESC(1, 0x5c, "TxMulti"), |
| MIB_DESC(1, 0x60, "TxUnderRun"), |
| MIB_DESC(1, 0x64, "Tx64Byte"), |
| MIB_DESC(1, 0x68, "Tx128Byte"), |
| MIB_DESC(1, 0x6c, "Tx256Byte"), |
| MIB_DESC(1, 0x70, "Tx512Byte"), |
| MIB_DESC(1, 0x74, "Tx1024Byte"), |
| MIB_DESC(1, 0x78, "Tx1518Byte"), |
| MIB_DESC(1, 0x7c, "TxMaxByte"), |
| MIB_DESC(1, 0x80, "TxOverSize"), |
| MIB_DESC(2, 0x84, "TxByte"), |
| MIB_DESC(1, 0x8c, "TxCollision"), |
| MIB_DESC(1, 0x90, "TxAbortCol"), |
| MIB_DESC(1, 0x94, "TxMultiCol"), |
| MIB_DESC(1, 0x98, "TxSingleCol"), |
| MIB_DESC(1, 0x9c, "TxExcDefer"), |
| MIB_DESC(1, 0xa0, "TxDefer"), |
| MIB_DESC(1, 0xa4, "TxLateCol"), |
| MIB_DESC(1, 0xa8, "RXUnicast"), |
| MIB_DESC(1, 0xac, "TXUnicast"), |
| }; |
| |
| /* The 32bit switch registers are accessed indirectly. To achieve this we need |
| * to set the page of the register. Track the last page that was set to reduce |
| * mdio writes |
| */ |
| static u16 qca8k_current_page = 0xffff; |
| |
| static void |
| qca8k_split_addr(u32 regaddr, u16 *r1, u16 *r2, u16 *page) |
| { |
| regaddr >>= 1; |
| *r1 = regaddr & 0x1e; |
| |
| regaddr >>= 5; |
| *r2 = regaddr & 0x7; |
| |
| regaddr >>= 3; |
| *page = regaddr & 0x3ff; |
| } |
| |
| static int |
| qca8k_mii_read32(struct mii_bus *bus, int phy_id, u32 regnum, u32 *val) |
| { |
| int ret; |
| |
| ret = bus->read(bus, phy_id, regnum); |
| if (ret >= 0) { |
| *val = ret; |
| ret = bus->read(bus, phy_id, regnum + 1); |
| *val |= ret << 16; |
| } |
| |
| if (ret < 0) { |
| dev_err_ratelimited(&bus->dev, |
| "failed to read qca8k 32bit register\n"); |
| *val = 0; |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static void |
| qca8k_mii_write32(struct mii_bus *bus, int phy_id, u32 regnum, u32 val) |
| { |
| u16 lo, hi; |
| int ret; |
| |
| lo = val & 0xffff; |
| hi = (u16)(val >> 16); |
| |
| ret = bus->write(bus, phy_id, regnum, lo); |
| if (ret >= 0) |
| ret = bus->write(bus, phy_id, regnum + 1, hi); |
| if (ret < 0) |
| dev_err_ratelimited(&bus->dev, |
| "failed to write qca8k 32bit register\n"); |
| } |
| |
| static int |
| qca8k_set_page(struct mii_bus *bus, u16 page) |
| { |
| int ret; |
| |
| if (page == qca8k_current_page) |
| return 0; |
| |
| ret = bus->write(bus, 0x18, 0, page); |
| if (ret < 0) { |
| dev_err_ratelimited(&bus->dev, |
| "failed to set qca8k page\n"); |
| return ret; |
| } |
| |
| qca8k_current_page = page; |
| usleep_range(1000, 2000); |
| return 0; |
| } |
| |
| static int |
| qca8k_read(struct qca8k_priv *priv, u32 reg, u32 *val) |
| { |
| return regmap_read(priv->regmap, reg, val); |
| } |
| |
| static int |
| qca8k_write(struct qca8k_priv *priv, u32 reg, u32 val) |
| { |
| return regmap_write(priv->regmap, reg, val); |
| } |
| |
| static int |
| qca8k_rmw(struct qca8k_priv *priv, u32 reg, u32 mask, u32 write_val) |
| { |
| return regmap_update_bits(priv->regmap, reg, mask, write_val); |
| } |
| |
| static int |
| qca8k_regmap_read(void *ctx, uint32_t reg, uint32_t *val) |
| { |
| struct qca8k_priv *priv = (struct qca8k_priv *)ctx; |
| struct mii_bus *bus = priv->bus; |
| u16 r1, r2, page; |
| int ret; |
| |
| qca8k_split_addr(reg, &r1, &r2, &page); |
| |
| mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED); |
| |
| ret = qca8k_set_page(bus, page); |
| if (ret < 0) |
| goto exit; |
| |
| ret = qca8k_mii_read32(bus, 0x10 | r2, r1, val); |
| |
| exit: |
| mutex_unlock(&bus->mdio_lock); |
| return ret; |
| } |
| |
| static int |
| qca8k_regmap_write(void *ctx, uint32_t reg, uint32_t val) |
| { |
| struct qca8k_priv *priv = (struct qca8k_priv *)ctx; |
| struct mii_bus *bus = priv->bus; |
| u16 r1, r2, page; |
| int ret; |
| |
| qca8k_split_addr(reg, &r1, &r2, &page); |
| |
| mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED); |
| |
| ret = qca8k_set_page(bus, page); |
| if (ret < 0) |
| goto exit; |
| |
| qca8k_mii_write32(bus, 0x10 | r2, r1, val); |
| |
| exit: |
| mutex_unlock(&bus->mdio_lock); |
| return ret; |
| } |
| |
| static int |
| qca8k_regmap_update_bits(void *ctx, uint32_t reg, uint32_t mask, uint32_t write_val) |
| { |
| struct qca8k_priv *priv = (struct qca8k_priv *)ctx; |
| struct mii_bus *bus = priv->bus; |
| u16 r1, r2, page; |
| u32 val; |
| int ret; |
| |
| qca8k_split_addr(reg, &r1, &r2, &page); |
| |
| mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED); |
| |
| ret = qca8k_set_page(bus, page); |
| if (ret < 0) |
| goto exit; |
| |
| ret = qca8k_mii_read32(bus, 0x10 | r2, r1, &val); |
| if (ret < 0) |
| goto exit; |
| |
| val &= ~mask; |
| val |= write_val; |
| qca8k_mii_write32(bus, 0x10 | r2, r1, val); |
| |
| exit: |
| mutex_unlock(&bus->mdio_lock); |
| |
| return ret; |
| } |
| |
| static const struct regmap_range qca8k_readable_ranges[] = { |
| regmap_reg_range(0x0000, 0x00e4), /* Global control */ |
| regmap_reg_range(0x0100, 0x0168), /* EEE control */ |
| regmap_reg_range(0x0200, 0x0270), /* Parser control */ |
| regmap_reg_range(0x0400, 0x0454), /* ACL */ |
| regmap_reg_range(0x0600, 0x0718), /* Lookup */ |
| regmap_reg_range(0x0800, 0x0b70), /* QM */ |
| regmap_reg_range(0x0c00, 0x0c80), /* PKT */ |
| regmap_reg_range(0x0e00, 0x0e98), /* L3 */ |
| regmap_reg_range(0x1000, 0x10ac), /* MIB - Port0 */ |
| regmap_reg_range(0x1100, 0x11ac), /* MIB - Port1 */ |
| regmap_reg_range(0x1200, 0x12ac), /* MIB - Port2 */ |
| regmap_reg_range(0x1300, 0x13ac), /* MIB - Port3 */ |
| regmap_reg_range(0x1400, 0x14ac), /* MIB - Port4 */ |
| regmap_reg_range(0x1500, 0x15ac), /* MIB - Port5 */ |
| regmap_reg_range(0x1600, 0x16ac), /* MIB - Port6 */ |
| |
| }; |
| |
| static const struct regmap_access_table qca8k_readable_table = { |
| .yes_ranges = qca8k_readable_ranges, |
| .n_yes_ranges = ARRAY_SIZE(qca8k_readable_ranges), |
| }; |
| |
| static struct regmap_config qca8k_regmap_config = { |
| .reg_bits = 16, |
| .val_bits = 32, |
| .reg_stride = 4, |
| .max_register = 0x16ac, /* end MIB - Port6 range */ |
| .reg_read = qca8k_regmap_read, |
| .reg_write = qca8k_regmap_write, |
| .reg_update_bits = qca8k_regmap_update_bits, |
| .rd_table = &qca8k_readable_table, |
| .disable_locking = true, /* Locking is handled by qca8k read/write */ |
| .cache_type = REGCACHE_NONE, /* Explicitly disable CACHE */ |
| }; |
| |
| static int |
| qca8k_busy_wait(struct qca8k_priv *priv, u32 reg, u32 mask) |
| { |
| u32 val; |
| |
| return regmap_read_poll_timeout(priv->regmap, reg, val, !(val & mask), 0, |
| QCA8K_BUSY_WAIT_TIMEOUT * USEC_PER_MSEC); |
| } |
| |
| static int |
| qca8k_fdb_read(struct qca8k_priv *priv, struct qca8k_fdb *fdb) |
| { |
| u32 reg[4], val; |
| int i, ret; |
| |
| /* load the ARL table into an array */ |
| for (i = 0; i < 4; i++) { |
| ret = qca8k_read(priv, QCA8K_REG_ATU_DATA0 + (i * 4), &val); |
| if (ret < 0) |
| return ret; |
| |
| reg[i] = val; |
| } |
| |
| /* vid - 83:72 */ |
| fdb->vid = FIELD_GET(QCA8K_ATU_VID_MASK, reg[2]); |
| /* aging - 67:64 */ |
| fdb->aging = FIELD_GET(QCA8K_ATU_STATUS_MASK, reg[2]); |
| /* portmask - 54:48 */ |
| fdb->port_mask = FIELD_GET(QCA8K_ATU_PORT_MASK, reg[1]); |
| /* mac - 47:0 */ |
| fdb->mac[0] = FIELD_GET(QCA8K_ATU_ADDR0_MASK, reg[1]); |
| fdb->mac[1] = FIELD_GET(QCA8K_ATU_ADDR1_MASK, reg[1]); |
| fdb->mac[2] = FIELD_GET(QCA8K_ATU_ADDR2_MASK, reg[0]); |
| fdb->mac[3] = FIELD_GET(QCA8K_ATU_ADDR3_MASK, reg[0]); |
| fdb->mac[4] = FIELD_GET(QCA8K_ATU_ADDR4_MASK, reg[0]); |
| fdb->mac[5] = FIELD_GET(QCA8K_ATU_ADDR5_MASK, reg[0]); |
| |
| return 0; |
| } |
| |
| static void |
| qca8k_fdb_write(struct qca8k_priv *priv, u16 vid, u8 port_mask, const u8 *mac, |
| u8 aging) |
| { |
| u32 reg[3] = { 0 }; |
| int i; |
| |
| /* vid - 83:72 */ |
| reg[2] = FIELD_PREP(QCA8K_ATU_VID_MASK, vid); |
| /* aging - 67:64 */ |
| reg[2] |= FIELD_PREP(QCA8K_ATU_STATUS_MASK, aging); |
| /* portmask - 54:48 */ |
| reg[1] = FIELD_PREP(QCA8K_ATU_PORT_MASK, port_mask); |
| /* mac - 47:0 */ |
| reg[1] |= FIELD_PREP(QCA8K_ATU_ADDR0_MASK, mac[0]); |
| reg[1] |= FIELD_PREP(QCA8K_ATU_ADDR1_MASK, mac[1]); |
| reg[0] |= FIELD_PREP(QCA8K_ATU_ADDR2_MASK, mac[2]); |
| reg[0] |= FIELD_PREP(QCA8K_ATU_ADDR3_MASK, mac[3]); |
| reg[0] |= FIELD_PREP(QCA8K_ATU_ADDR4_MASK, mac[4]); |
| reg[0] |= FIELD_PREP(QCA8K_ATU_ADDR5_MASK, mac[5]); |
| |
| /* load the array into the ARL table */ |
| for (i = 0; i < 3; i++) |
| qca8k_write(priv, QCA8K_REG_ATU_DATA0 + (i * 4), reg[i]); |
| } |
| |
| static int |
| qca8k_fdb_access(struct qca8k_priv *priv, enum qca8k_fdb_cmd cmd, int port) |
| { |
| u32 reg; |
| int ret; |
| |
| /* Set the command and FDB index */ |
| reg = QCA8K_ATU_FUNC_BUSY; |
| reg |= cmd; |
| if (port >= 0) { |
| reg |= QCA8K_ATU_FUNC_PORT_EN; |
| reg |= FIELD_PREP(QCA8K_ATU_FUNC_PORT_MASK, port); |
| } |
| |
| /* Write the function register triggering the table access */ |
| ret = qca8k_write(priv, QCA8K_REG_ATU_FUNC, reg); |
| if (ret) |
| return ret; |
| |
| /* wait for completion */ |
| ret = qca8k_busy_wait(priv, QCA8K_REG_ATU_FUNC, QCA8K_ATU_FUNC_BUSY); |
| if (ret) |
| return ret; |
| |
| /* Check for table full violation when adding an entry */ |
| if (cmd == QCA8K_FDB_LOAD) { |
| ret = qca8k_read(priv, QCA8K_REG_ATU_FUNC, ®); |
| if (ret < 0) |
| return ret; |
| if (reg & QCA8K_ATU_FUNC_FULL) |
| return -1; |
| } |
| |
| return 0; |
| } |
| |
| static int |
| qca8k_fdb_next(struct qca8k_priv *priv, struct qca8k_fdb *fdb, int port) |
| { |
| int ret; |
| |
| qca8k_fdb_write(priv, fdb->vid, fdb->port_mask, fdb->mac, fdb->aging); |
| ret = qca8k_fdb_access(priv, QCA8K_FDB_NEXT, port); |
| if (ret < 0) |
| return ret; |
| |
| return qca8k_fdb_read(priv, fdb); |
| } |
| |
| static int |
| qca8k_fdb_add(struct qca8k_priv *priv, const u8 *mac, u16 port_mask, |
| u16 vid, u8 aging) |
| { |
| int ret; |
| |
| mutex_lock(&priv->reg_mutex); |
| qca8k_fdb_write(priv, vid, port_mask, mac, aging); |
| ret = qca8k_fdb_access(priv, QCA8K_FDB_LOAD, -1); |
| mutex_unlock(&priv->reg_mutex); |
| |
| return ret; |
| } |
| |
| static int |
| qca8k_fdb_del(struct qca8k_priv *priv, const u8 *mac, u16 port_mask, u16 vid) |
| { |
| int ret; |
| |
| mutex_lock(&priv->reg_mutex); |
| qca8k_fdb_write(priv, vid, port_mask, mac, 0); |
| ret = qca8k_fdb_access(priv, QCA8K_FDB_PURGE, -1); |
| mutex_unlock(&priv->reg_mutex); |
| |
| return ret; |
| } |
| |
| static void |
| qca8k_fdb_flush(struct qca8k_priv *priv) |
| { |
| mutex_lock(&priv->reg_mutex); |
| qca8k_fdb_access(priv, QCA8K_FDB_FLUSH, -1); |
| mutex_unlock(&priv->reg_mutex); |
| } |
| |
| static int |
| qca8k_fdb_search_and_insert(struct qca8k_priv *priv, u8 port_mask, |
| const u8 *mac, u16 vid) |
| { |
| struct qca8k_fdb fdb = { 0 }; |
| int ret; |
| |
| mutex_lock(&priv->reg_mutex); |
| |
| qca8k_fdb_write(priv, vid, 0, mac, 0); |
| ret = qca8k_fdb_access(priv, QCA8K_FDB_SEARCH, -1); |
| if (ret < 0) |
| goto exit; |
| |
| ret = qca8k_fdb_read(priv, &fdb); |
| if (ret < 0) |
| goto exit; |
| |
| /* Rule exist. Delete first */ |
| if (!fdb.aging) { |
| ret = qca8k_fdb_access(priv, QCA8K_FDB_PURGE, -1); |
| if (ret) |
| goto exit; |
| } |
| |
| /* Add port to fdb portmask */ |
| fdb.port_mask |= port_mask; |
| |
| qca8k_fdb_write(priv, vid, fdb.port_mask, mac, fdb.aging); |
| ret = qca8k_fdb_access(priv, QCA8K_FDB_LOAD, -1); |
| |
| exit: |
| mutex_unlock(&priv->reg_mutex); |
| return ret; |
| } |
| |
| static int |
| qca8k_fdb_search_and_del(struct qca8k_priv *priv, u8 port_mask, |
| const u8 *mac, u16 vid) |
| { |
| struct qca8k_fdb fdb = { 0 }; |
| int ret; |
| |
| mutex_lock(&priv->reg_mutex); |
| |
| qca8k_fdb_write(priv, vid, 0, mac, 0); |
| ret = qca8k_fdb_access(priv, QCA8K_FDB_SEARCH, -1); |
| if (ret < 0) |
| goto exit; |
| |
| /* Rule doesn't exist. Why delete? */ |
| if (!fdb.aging) { |
| ret = -EINVAL; |
| goto exit; |
| } |
| |
| ret = qca8k_fdb_access(priv, QCA8K_FDB_PURGE, -1); |
| if (ret) |
| goto exit; |
| |
| /* Only port in the rule is this port. Don't re insert */ |
| if (fdb.port_mask == port_mask) |
| goto exit; |
| |
| /* Remove port from port mask */ |
| fdb.port_mask &= ~port_mask; |
| |
| qca8k_fdb_write(priv, vid, fdb.port_mask, mac, fdb.aging); |
| ret = qca8k_fdb_access(priv, QCA8K_FDB_LOAD, -1); |
| |
| exit: |
| mutex_unlock(&priv->reg_mutex); |
| return ret; |
| } |
| |
| static int |
| qca8k_vlan_access(struct qca8k_priv *priv, enum qca8k_vlan_cmd cmd, u16 vid) |
| { |
| u32 reg; |
| int ret; |
| |
| /* Set the command and VLAN index */ |
| reg = QCA8K_VTU_FUNC1_BUSY; |
| reg |= cmd; |
| reg |= FIELD_PREP(QCA8K_VTU_FUNC1_VID_MASK, vid); |
| |
| /* Write the function register triggering the table access */ |
| ret = qca8k_write(priv, QCA8K_REG_VTU_FUNC1, reg); |
| if (ret) |
| return ret; |
| |
| /* wait for completion */ |
| ret = qca8k_busy_wait(priv, QCA8K_REG_VTU_FUNC1, QCA8K_VTU_FUNC1_BUSY); |
| if (ret) |
| return ret; |
| |
| /* Check for table full violation when adding an entry */ |
| if (cmd == QCA8K_VLAN_LOAD) { |
| ret = qca8k_read(priv, QCA8K_REG_VTU_FUNC1, ®); |
| if (ret < 0) |
| return ret; |
| if (reg & QCA8K_VTU_FUNC1_FULL) |
| return -ENOMEM; |
| } |
| |
| return 0; |
| } |
| |
| static int |
| qca8k_vlan_add(struct qca8k_priv *priv, u8 port, u16 vid, bool untagged) |
| { |
| u32 reg; |
| int ret; |
| |
| /* |
| We do the right thing with VLAN 0 and treat it as untagged while |
| preserving the tag on egress. |
| */ |
| if (vid == 0) |
| return 0; |
| |
| mutex_lock(&priv->reg_mutex); |
| ret = qca8k_vlan_access(priv, QCA8K_VLAN_READ, vid); |
| if (ret < 0) |
| goto out; |
| |
| ret = qca8k_read(priv, QCA8K_REG_VTU_FUNC0, ®); |
| if (ret < 0) |
| goto out; |
| reg |= QCA8K_VTU_FUNC0_VALID | QCA8K_VTU_FUNC0_IVL_EN; |
| reg &= ~QCA8K_VTU_FUNC0_EG_MODE_PORT_MASK(port); |
| if (untagged) |
| reg |= QCA8K_VTU_FUNC0_EG_MODE_PORT_UNTAG(port); |
| else |
| reg |= QCA8K_VTU_FUNC0_EG_MODE_PORT_TAG(port); |
| |
| ret = qca8k_write(priv, QCA8K_REG_VTU_FUNC0, reg); |
| if (ret) |
| goto out; |
| ret = qca8k_vlan_access(priv, QCA8K_VLAN_LOAD, vid); |
| |
| out: |
| mutex_unlock(&priv->reg_mutex); |
| |
| return ret; |
| } |
| |
| static int |
| qca8k_vlan_del(struct qca8k_priv *priv, u8 port, u16 vid) |
| { |
| u32 reg, mask; |
| int ret, i; |
| bool del; |
| |
| mutex_lock(&priv->reg_mutex); |
| ret = qca8k_vlan_access(priv, QCA8K_VLAN_READ, vid); |
| if (ret < 0) |
| goto out; |
| |
| ret = qca8k_read(priv, QCA8K_REG_VTU_FUNC0, ®); |
| if (ret < 0) |
| goto out; |
| reg &= ~QCA8K_VTU_FUNC0_EG_MODE_PORT_MASK(port); |
| reg |= QCA8K_VTU_FUNC0_EG_MODE_PORT_NOT(port); |
| |
| /* Check if we're the last member to be removed */ |
| del = true; |
| for (i = 0; i < QCA8K_NUM_PORTS; i++) { |
| mask = QCA8K_VTU_FUNC0_EG_MODE_PORT_NOT(i); |
| |
| if ((reg & mask) != mask) { |
| del = false; |
| break; |
| } |
| } |
| |
| if (del) { |
| ret = qca8k_vlan_access(priv, QCA8K_VLAN_PURGE, vid); |
| } else { |
| ret = qca8k_write(priv, QCA8K_REG_VTU_FUNC0, reg); |
| if (ret) |
| goto out; |
| ret = qca8k_vlan_access(priv, QCA8K_VLAN_LOAD, vid); |
| } |
| |
| out: |
| mutex_unlock(&priv->reg_mutex); |
| |
| return ret; |
| } |
| |
| static int |
| qca8k_mib_init(struct qca8k_priv *priv) |
| { |
| int ret; |
| |
| mutex_lock(&priv->reg_mutex); |
| ret = regmap_set_bits(priv->regmap, QCA8K_REG_MIB, QCA8K_MIB_FLUSH | QCA8K_MIB_BUSY); |
| if (ret) |
| goto exit; |
| |
| ret = qca8k_busy_wait(priv, QCA8K_REG_MIB, QCA8K_MIB_BUSY); |
| if (ret) |
| goto exit; |
| |
| ret = regmap_set_bits(priv->regmap, QCA8K_REG_MIB, QCA8K_MIB_CPU_KEEP); |
| if (ret) |
| goto exit; |
| |
| ret = qca8k_write(priv, QCA8K_REG_MODULE_EN, QCA8K_MODULE_EN_MIB); |
| |
| exit: |
| mutex_unlock(&priv->reg_mutex); |
| return ret; |
| } |
| |
| static void |
| qca8k_port_set_status(struct qca8k_priv *priv, int port, int enable) |
| { |
| u32 mask = QCA8K_PORT_STATUS_TXMAC | QCA8K_PORT_STATUS_RXMAC; |
| |
| /* Port 0 and 6 have no internal PHY */ |
| if (port > 0 && port < 6) |
| mask |= QCA8K_PORT_STATUS_LINK_AUTO; |
| |
| if (enable) |
| regmap_set_bits(priv->regmap, QCA8K_REG_PORT_STATUS(port), mask); |
| else |
| regmap_clear_bits(priv->regmap, QCA8K_REG_PORT_STATUS(port), mask); |
| } |
| |
| static u32 |
| qca8k_port_to_phy(int port) |
| { |
| /* From Andrew Lunn: |
| * Port 0 has no internal phy. |
| * Port 1 has an internal PHY at MDIO address 0. |
| * Port 2 has an internal PHY at MDIO address 1. |
| * ... |
| * Port 5 has an internal PHY at MDIO address 4. |
| * Port 6 has no internal PHY. |
| */ |
| |
| return port - 1; |
| } |
| |
| static int |
| qca8k_mdio_busy_wait(struct mii_bus *bus, u32 reg, u32 mask) |
| { |
| u16 r1, r2, page; |
| u32 val; |
| int ret, ret1; |
| |
| qca8k_split_addr(reg, &r1, &r2, &page); |
| |
| ret = read_poll_timeout(qca8k_mii_read32, ret1, !(val & mask), 0, |
| QCA8K_BUSY_WAIT_TIMEOUT * USEC_PER_MSEC, false, |
| bus, 0x10 | r2, r1, &val); |
| |
| /* Check if qca8k_read has failed for a different reason |
| * before returnting -ETIMEDOUT |
| */ |
| if (ret < 0 && ret1 < 0) |
| return ret1; |
| |
| return ret; |
| } |
| |
| static int |
| qca8k_mdio_write(struct mii_bus *bus, int phy, int regnum, u16 data) |
| { |
| u16 r1, r2, page; |
| u32 val; |
| int ret; |
| |
| if (regnum >= QCA8K_MDIO_MASTER_MAX_REG) |
| return -EINVAL; |
| |
| val = QCA8K_MDIO_MASTER_BUSY | QCA8K_MDIO_MASTER_EN | |
| QCA8K_MDIO_MASTER_WRITE | QCA8K_MDIO_MASTER_PHY_ADDR(phy) | |
| QCA8K_MDIO_MASTER_REG_ADDR(regnum) | |
| QCA8K_MDIO_MASTER_DATA(data); |
| |
| qca8k_split_addr(QCA8K_MDIO_MASTER_CTRL, &r1, &r2, &page); |
| |
| mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED); |
| |
| ret = qca8k_set_page(bus, page); |
| if (ret) |
| goto exit; |
| |
| qca8k_mii_write32(bus, 0x10 | r2, r1, val); |
| |
| ret = qca8k_mdio_busy_wait(bus, QCA8K_MDIO_MASTER_CTRL, |
| QCA8K_MDIO_MASTER_BUSY); |
| |
| exit: |
| /* even if the busy_wait timeouts try to clear the MASTER_EN */ |
| qca8k_mii_write32(bus, 0x10 | r2, r1, 0); |
| |
| mutex_unlock(&bus->mdio_lock); |
| |
| return ret; |
| } |
| |
| static int |
| qca8k_mdio_read(struct mii_bus *bus, int phy, int regnum) |
| { |
| u16 r1, r2, page; |
| u32 val; |
| int ret; |
| |
| if (regnum >= QCA8K_MDIO_MASTER_MAX_REG) |
| return -EINVAL; |
| |
| val = QCA8K_MDIO_MASTER_BUSY | QCA8K_MDIO_MASTER_EN | |
| QCA8K_MDIO_MASTER_READ | QCA8K_MDIO_MASTER_PHY_ADDR(phy) | |
| QCA8K_MDIO_MASTER_REG_ADDR(regnum); |
| |
| qca8k_split_addr(QCA8K_MDIO_MASTER_CTRL, &r1, &r2, &page); |
| |
| mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED); |
| |
| ret = qca8k_set_page(bus, page); |
| if (ret) |
| goto exit; |
| |
| qca8k_mii_write32(bus, 0x10 | r2, r1, val); |
| |
| ret = qca8k_mdio_busy_wait(bus, QCA8K_MDIO_MASTER_CTRL, |
| QCA8K_MDIO_MASTER_BUSY); |
| if (ret) |
| goto exit; |
| |
| ret = qca8k_mii_read32(bus, 0x10 | r2, r1, &val); |
| |
| exit: |
| /* even if the busy_wait timeouts try to clear the MASTER_EN */ |
| qca8k_mii_write32(bus, 0x10 | r2, r1, 0); |
| |
| mutex_unlock(&bus->mdio_lock); |
| |
| if (ret >= 0) |
| ret = val & QCA8K_MDIO_MASTER_DATA_MASK; |
| |
| return ret; |
| } |
| |
| static int |
| qca8k_internal_mdio_write(struct mii_bus *slave_bus, int phy, int regnum, u16 data) |
| { |
| struct qca8k_priv *priv = slave_bus->priv; |
| struct mii_bus *bus = priv->bus; |
| |
| return qca8k_mdio_write(bus, phy, regnum, data); |
| } |
| |
| static int |
| qca8k_internal_mdio_read(struct mii_bus *slave_bus, int phy, int regnum) |
| { |
| struct qca8k_priv *priv = slave_bus->priv; |
| struct mii_bus *bus = priv->bus; |
| |
| return qca8k_mdio_read(bus, phy, regnum); |
| } |
| |
| static int |
| qca8k_phy_write(struct dsa_switch *ds, int port, int regnum, u16 data) |
| { |
| struct qca8k_priv *priv = ds->priv; |
| |
| /* Check if the legacy mapping should be used and the |
| * port is not correctly mapped to the right PHY in the |
| * devicetree |
| */ |
| if (priv->legacy_phy_port_mapping) |
| port = qca8k_port_to_phy(port) % PHY_MAX_ADDR; |
| |
| return qca8k_mdio_write(priv->bus, port, regnum, data); |
| } |
| |
| static int |
| qca8k_phy_read(struct dsa_switch *ds, int port, int regnum) |
| { |
| struct qca8k_priv *priv = ds->priv; |
| int ret; |
| |
| /* Check if the legacy mapping should be used and the |
| * port is not correctly mapped to the right PHY in the |
| * devicetree |
| */ |
| if (priv->legacy_phy_port_mapping) |
| port = qca8k_port_to_phy(port) % PHY_MAX_ADDR; |
| |
| ret = qca8k_mdio_read(priv->bus, port, regnum); |
| |
| if (ret < 0) |
| return 0xffff; |
| |
| return ret; |
| } |
| |
| static int |
| qca8k_mdio_register(struct qca8k_priv *priv, struct device_node *mdio) |
| { |
| struct dsa_switch *ds = priv->ds; |
| struct mii_bus *bus; |
| |
| bus = devm_mdiobus_alloc(ds->dev); |
| |
| if (!bus) |
| return -ENOMEM; |
| |
| bus->priv = (void *)priv; |
| bus->name = "qca8k slave mii"; |
| bus->read = qca8k_internal_mdio_read; |
| bus->write = qca8k_internal_mdio_write; |
| snprintf(bus->id, MII_BUS_ID_SIZE, "qca8k-%d", |
| ds->index); |
| |
| bus->parent = ds->dev; |
| bus->phy_mask = ~ds->phys_mii_mask; |
| |
| ds->slave_mii_bus = bus; |
| |
| return devm_of_mdiobus_register(priv->dev, bus, mdio); |
| } |
| |
| static int |
| qca8k_setup_mdio_bus(struct qca8k_priv *priv) |
| { |
| u32 internal_mdio_mask = 0, external_mdio_mask = 0, reg; |
| struct device_node *ports, *port, *mdio; |
| phy_interface_t mode; |
| int err; |
| |
| ports = of_get_child_by_name(priv->dev->of_node, "ports"); |
| if (!ports) |
| ports = of_get_child_by_name(priv->dev->of_node, "ethernet-ports"); |
| |
| if (!ports) |
| return -EINVAL; |
| |
| for_each_available_child_of_node(ports, port) { |
| err = of_property_read_u32(port, "reg", ®); |
| if (err) { |
| of_node_put(port); |
| of_node_put(ports); |
| return err; |
| } |
| |
| if (!dsa_is_user_port(priv->ds, reg)) |
| continue; |
| |
| of_get_phy_mode(port, &mode); |
| |
| if (of_property_read_bool(port, "phy-handle") && |
| mode != PHY_INTERFACE_MODE_INTERNAL) |
| external_mdio_mask |= BIT(reg); |
| else |
| internal_mdio_mask |= BIT(reg); |
| } |
| |
| of_node_put(ports); |
| if (!external_mdio_mask && !internal_mdio_mask) { |
| dev_err(priv->dev, "no PHYs are defined.\n"); |
| return -EINVAL; |
| } |
| |
| /* The QCA8K_MDIO_MASTER_EN Bit, which grants access to PHYs through |
| * the MDIO_MASTER register also _disconnects_ the external MDC |
| * passthrough to the internal PHYs. It's not possible to use both |
| * configurations at the same time! |
| * |
| * Because this came up during the review process: |
| * If the external mdio-bus driver is capable magically disabling |
| * the QCA8K_MDIO_MASTER_EN and mutex/spin-locking out the qca8k's |
| * accessors for the time being, it would be possible to pull this |
| * off. |
| */ |
| if (!!external_mdio_mask && !!internal_mdio_mask) { |
| dev_err(priv->dev, "either internal or external mdio bus configuration is supported.\n"); |
| return -EINVAL; |
| } |
| |
| if (external_mdio_mask) { |
| /* Make sure to disable the internal mdio bus in cases |
| * a dt-overlay and driver reload changed the configuration |
| */ |
| |
| return regmap_clear_bits(priv->regmap, QCA8K_MDIO_MASTER_CTRL, |
| QCA8K_MDIO_MASTER_EN); |
| } |
| |
| /* Check if the devicetree declare the port:phy mapping */ |
| mdio = of_get_child_by_name(priv->dev->of_node, "mdio"); |
| if (of_device_is_available(mdio)) { |
| err = qca8k_mdio_register(priv, mdio); |
| if (err) |
| of_node_put(mdio); |
| |
| return err; |
| } |
| |
| /* If a mapping can't be found the legacy mapping is used, |
| * using the qca8k_port_to_phy function |
| */ |
| priv->legacy_phy_port_mapping = true; |
| priv->ops.phy_read = qca8k_phy_read; |
| priv->ops.phy_write = qca8k_phy_write; |
| |
| return 0; |
| } |
| |
| static int |
| qca8k_setup_mac_pwr_sel(struct qca8k_priv *priv) |
| { |
| u32 mask = 0; |
| int ret = 0; |
| |
| /* SoC specific settings for ipq8064. |
| * If more device require this consider adding |
| * a dedicated binding. |
| */ |
| if (of_machine_is_compatible("qcom,ipq8064")) |
| mask |= QCA8K_MAC_PWR_RGMII0_1_8V; |
| |
| /* SoC specific settings for ipq8065 */ |
| if (of_machine_is_compatible("qcom,ipq8065")) |
| mask |= QCA8K_MAC_PWR_RGMII1_1_8V; |
| |
| if (mask) { |
| ret = qca8k_rmw(priv, QCA8K_REG_MAC_PWR_SEL, |
| QCA8K_MAC_PWR_RGMII0_1_8V | |
| QCA8K_MAC_PWR_RGMII1_1_8V, |
| mask); |
| } |
| |
| return ret; |
| } |
| |
| static int qca8k_find_cpu_port(struct dsa_switch *ds) |
| { |
| struct qca8k_priv *priv = ds->priv; |
| |
| /* Find the connected cpu port. Valid port are 0 or 6 */ |
| if (dsa_is_cpu_port(ds, 0)) |
| return 0; |
| |
| dev_dbg(priv->dev, "port 0 is not the CPU port. Checking port 6"); |
| |
| if (dsa_is_cpu_port(ds, 6)) |
| return 6; |
| |
| return -EINVAL; |
| } |
| |
| static int |
| qca8k_setup_of_pws_reg(struct qca8k_priv *priv) |
| { |
| struct device_node *node = priv->dev->of_node; |
| const struct qca8k_match_data *data; |
| u32 val = 0; |
| int ret; |
| |
| /* QCA8327 require to set to the correct mode. |
| * His bigger brother QCA8328 have the 172 pin layout. |
| * Should be applied by default but we set this just to make sure. |
| */ |
| if (priv->switch_id == QCA8K_ID_QCA8327) { |
| data = of_device_get_match_data(priv->dev); |
| |
| /* Set the correct package of 148 pin for QCA8327 */ |
| if (data->reduced_package) |
| val |= QCA8327_PWS_PACKAGE148_EN; |
| |
| ret = qca8k_rmw(priv, QCA8K_REG_PWS, QCA8327_PWS_PACKAGE148_EN, |
| val); |
| if (ret) |
| return ret; |
| } |
| |
| if (of_property_read_bool(node, "qca,ignore-power-on-sel")) |
| val |= QCA8K_PWS_POWER_ON_SEL; |
| |
| if (of_property_read_bool(node, "qca,led-open-drain")) { |
| if (!(val & QCA8K_PWS_POWER_ON_SEL)) { |
| dev_err(priv->dev, "qca,led-open-drain require qca,ignore-power-on-sel to be set."); |
| return -EINVAL; |
| } |
| |
| val |= QCA8K_PWS_LED_OPEN_EN_CSR; |
| } |
| |
| return qca8k_rmw(priv, QCA8K_REG_PWS, |
| QCA8K_PWS_LED_OPEN_EN_CSR | QCA8K_PWS_POWER_ON_SEL, |
| val); |
| } |
| |
| static int |
| qca8k_parse_port_config(struct qca8k_priv *priv) |
| { |
| int port, cpu_port_index = -1, ret; |
| struct device_node *port_dn; |
| phy_interface_t mode; |
| struct dsa_port *dp; |
| u32 delay; |
| |
| /* We have 2 CPU port. Check them */ |
| for (port = 0; port < QCA8K_NUM_PORTS; port++) { |
| /* Skip every other port */ |
| if (port != 0 && port != 6) |
| continue; |
| |
| dp = dsa_to_port(priv->ds, port); |
| port_dn = dp->dn; |
| cpu_port_index++; |
| |
| if (!of_device_is_available(port_dn)) |
| continue; |
| |
| ret = of_get_phy_mode(port_dn, &mode); |
| if (ret) |
| continue; |
| |
| switch (mode) { |
| case PHY_INTERFACE_MODE_RGMII: |
| case PHY_INTERFACE_MODE_RGMII_ID: |
| case PHY_INTERFACE_MODE_RGMII_TXID: |
| case PHY_INTERFACE_MODE_RGMII_RXID: |
| case PHY_INTERFACE_MODE_SGMII: |
| delay = 0; |
| |
| if (!of_property_read_u32(port_dn, "tx-internal-delay-ps", &delay)) |
| /* Switch regs accept value in ns, convert ps to ns */ |
| delay = delay / 1000; |
| else if (mode == PHY_INTERFACE_MODE_RGMII_ID || |
| mode == PHY_INTERFACE_MODE_RGMII_TXID) |
| delay = 1; |
| |
| if (!FIELD_FIT(QCA8K_PORT_PAD_RGMII_TX_DELAY_MASK, delay)) { |
| dev_err(priv->dev, "rgmii tx delay is limited to a max value of 3ns, setting to the max value"); |
| delay = 3; |
| } |
| |
| priv->ports_config.rgmii_tx_delay[cpu_port_index] = delay; |
| |
| delay = 0; |
| |
| if (!of_property_read_u32(port_dn, "rx-internal-delay-ps", &delay)) |
| /* Switch regs accept value in ns, convert ps to ns */ |
| delay = delay / 1000; |
| else if (mode == PHY_INTERFACE_MODE_RGMII_ID || |
| mode == PHY_INTERFACE_MODE_RGMII_RXID) |
| delay = 2; |
| |
| if (!FIELD_FIT(QCA8K_PORT_PAD_RGMII_RX_DELAY_MASK, delay)) { |
| dev_err(priv->dev, "rgmii rx delay is limited to a max value of 3ns, setting to the max value"); |
| delay = 3; |
| } |
| |
| priv->ports_config.rgmii_rx_delay[cpu_port_index] = delay; |
| |
| /* Skip sgmii parsing for rgmii* mode */ |
| if (mode == PHY_INTERFACE_MODE_RGMII || |
| mode == PHY_INTERFACE_MODE_RGMII_ID || |
| mode == PHY_INTERFACE_MODE_RGMII_TXID || |
| mode == PHY_INTERFACE_MODE_RGMII_RXID) |
| break; |
| |
| if (of_property_read_bool(port_dn, "qca,sgmii-txclk-falling-edge")) |
| priv->ports_config.sgmii_tx_clk_falling_edge = true; |
| |
| if (of_property_read_bool(port_dn, "qca,sgmii-rxclk-falling-edge")) |
| priv->ports_config.sgmii_rx_clk_falling_edge = true; |
| |
| if (of_property_read_bool(port_dn, "qca,sgmii-enable-pll")) { |
| priv->ports_config.sgmii_enable_pll = true; |
| |
| if (priv->switch_id == QCA8K_ID_QCA8327) { |
| dev_err(priv->dev, "SGMII PLL should NOT be enabled for qca8327. Aborting enabling"); |
| priv->ports_config.sgmii_enable_pll = false; |
| } |
| |
| if (priv->switch_revision < 2) |
| dev_warn(priv->dev, "SGMII PLL should NOT be enabled for qca8337 with revision 2 or more."); |
| } |
| |
| break; |
| default: |
| continue; |
| } |
| } |
| |
| return 0; |
| } |
| |
| static int |
| qca8k_setup(struct dsa_switch *ds) |
| { |
| struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; |
| int cpu_port, ret, i; |
| u32 mask; |
| |
| cpu_port = qca8k_find_cpu_port(ds); |
| if (cpu_port < 0) { |
| dev_err(priv->dev, "No cpu port configured in both cpu port0 and port6"); |
| return cpu_port; |
| } |
| |
| /* Parse CPU port config to be later used in phy_link mac_config */ |
| ret = qca8k_parse_port_config(priv); |
| if (ret) |
| return ret; |
| |
| ret = qca8k_setup_mdio_bus(priv); |
| if (ret) |
| return ret; |
| |
| ret = qca8k_setup_of_pws_reg(priv); |
| if (ret) |
| return ret; |
| |
| ret = qca8k_setup_mac_pwr_sel(priv); |
| if (ret) |
| return ret; |
| |
| /* Make sure MAC06 is disabled */ |
| ret = regmap_clear_bits(priv->regmap, QCA8K_REG_PORT0_PAD_CTRL, |
| QCA8K_PORT0_PAD_MAC06_EXCHANGE_EN); |
| if (ret) { |
| dev_err(priv->dev, "failed disabling MAC06 exchange"); |
| return ret; |
| } |
| |
| /* Enable CPU Port */ |
| ret = regmap_set_bits(priv->regmap, QCA8K_REG_GLOBAL_FW_CTRL0, |
| QCA8K_GLOBAL_FW_CTRL0_CPU_PORT_EN); |
| if (ret) { |
| dev_err(priv->dev, "failed enabling CPU port"); |
| return ret; |
| } |
| |
| /* Enable MIB counters */ |
| ret = qca8k_mib_init(priv); |
| if (ret) |
| dev_warn(priv->dev, "mib init failed"); |
| |
| /* Initial setup of all ports */ |
| for (i = 0; i < QCA8K_NUM_PORTS; i++) { |
| /* Disable forwarding by default on all ports */ |
| ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(i), |
| QCA8K_PORT_LOOKUP_MEMBER, 0); |
| if (ret) |
| return ret; |
| |
| /* Enable QCA header mode on all cpu ports */ |
| if (dsa_is_cpu_port(ds, i)) { |
| ret = qca8k_write(priv, QCA8K_REG_PORT_HDR_CTRL(i), |
| FIELD_PREP(QCA8K_PORT_HDR_CTRL_TX_MASK, QCA8K_PORT_HDR_CTRL_ALL) | |
| FIELD_PREP(QCA8K_PORT_HDR_CTRL_RX_MASK, QCA8K_PORT_HDR_CTRL_ALL)); |
| if (ret) { |
| dev_err(priv->dev, "failed enabling QCA header mode"); |
| return ret; |
| } |
| } |
| |
| /* Disable MAC by default on all user ports */ |
| if (dsa_is_user_port(ds, i)) |
| qca8k_port_set_status(priv, i, 0); |
| } |
| |
| /* Forward all unknown frames to CPU port for Linux processing |
| * Notice that in multi-cpu config only one port should be set |
| * for igmp, unknown, multicast and broadcast packet |
| */ |
| ret = qca8k_write(priv, QCA8K_REG_GLOBAL_FW_CTRL1, |
| FIELD_PREP(QCA8K_GLOBAL_FW_CTRL1_IGMP_DP_MASK, BIT(cpu_port)) | |
| FIELD_PREP(QCA8K_GLOBAL_FW_CTRL1_BC_DP_MASK, BIT(cpu_port)) | |
| FIELD_PREP(QCA8K_GLOBAL_FW_CTRL1_MC_DP_MASK, BIT(cpu_port)) | |
| FIELD_PREP(QCA8K_GLOBAL_FW_CTRL1_UC_DP_MASK, BIT(cpu_port))); |
| if (ret) |
| return ret; |
| |
| /* Setup connection between CPU port & user ports |
| * Configure specific switch configuration for ports |
| */ |
| for (i = 0; i < QCA8K_NUM_PORTS; i++) { |
| /* CPU port gets connected to all user ports of the switch */ |
| if (dsa_is_cpu_port(ds, i)) { |
| ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(i), |
| QCA8K_PORT_LOOKUP_MEMBER, dsa_user_ports(ds)); |
| if (ret) |
| return ret; |
| } |
| |
| /* Individual user ports get connected to CPU port only */ |
| if (dsa_is_user_port(ds, i)) { |
| ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(i), |
| QCA8K_PORT_LOOKUP_MEMBER, |
| BIT(cpu_port)); |
| if (ret) |
| return ret; |
| |
| /* Enable ARP Auto-learning by default */ |
| ret = regmap_set_bits(priv->regmap, QCA8K_PORT_LOOKUP_CTRL(i), |
| QCA8K_PORT_LOOKUP_LEARN); |
| if (ret) |
| return ret; |
| |
| /* For port based vlans to work we need to set the |
| * default egress vid |
| */ |
| ret = qca8k_rmw(priv, QCA8K_EGRESS_VLAN(i), |
| QCA8K_EGREES_VLAN_PORT_MASK(i), |
| QCA8K_EGREES_VLAN_PORT(i, QCA8K_PORT_VID_DEF)); |
| if (ret) |
| return ret; |
| |
| ret = qca8k_write(priv, QCA8K_REG_PORT_VLAN_CTRL0(i), |
| QCA8K_PORT_VLAN_CVID(QCA8K_PORT_VID_DEF) | |
| QCA8K_PORT_VLAN_SVID(QCA8K_PORT_VID_DEF)); |
| if (ret) |
| return ret; |
| } |
| |
| /* The port 5 of the qca8337 have some problem in flood condition. The |
| * original legacy driver had some specific buffer and priority settings |
| * for the different port suggested by the QCA switch team. Add this |
| * missing settings to improve switch stability under load condition. |
| * This problem is limited to qca8337 and other qca8k switch are not affected. |
| */ |
| if (priv->switch_id == QCA8K_ID_QCA8337) { |
| switch (i) { |
| /* The 2 CPU port and port 5 requires some different |
| * priority than any other ports. |
| */ |
| case 0: |
| case 5: |
| case 6: |
| mask = QCA8K_PORT_HOL_CTRL0_EG_PRI0(0x3) | |
| QCA8K_PORT_HOL_CTRL0_EG_PRI1(0x4) | |
| QCA8K_PORT_HOL_CTRL0_EG_PRI2(0x4) | |
| QCA8K_PORT_HOL_CTRL0_EG_PRI3(0x4) | |
| QCA8K_PORT_HOL_CTRL0_EG_PRI4(0x6) | |
| QCA8K_PORT_HOL_CTRL0_EG_PRI5(0x8) | |
| QCA8K_PORT_HOL_CTRL0_EG_PORT(0x1e); |
| break; |
| default: |
| mask = QCA8K_PORT_HOL_CTRL0_EG_PRI0(0x3) | |
| QCA8K_PORT_HOL_CTRL0_EG_PRI1(0x4) | |
| QCA8K_PORT_HOL_CTRL0_EG_PRI2(0x6) | |
| QCA8K_PORT_HOL_CTRL0_EG_PRI3(0x8) | |
| QCA8K_PORT_HOL_CTRL0_EG_PORT(0x19); |
| } |
| qca8k_write(priv, QCA8K_REG_PORT_HOL_CTRL0(i), mask); |
| |
| mask = QCA8K_PORT_HOL_CTRL1_ING(0x6) | |
| QCA8K_PORT_HOL_CTRL1_EG_PRI_BUF_EN | |
| QCA8K_PORT_HOL_CTRL1_EG_PORT_BUF_EN | |
| QCA8K_PORT_HOL_CTRL1_WRED_EN; |
| qca8k_rmw(priv, QCA8K_REG_PORT_HOL_CTRL1(i), |
| QCA8K_PORT_HOL_CTRL1_ING_BUF_MASK | |
| QCA8K_PORT_HOL_CTRL1_EG_PRI_BUF_EN | |
| QCA8K_PORT_HOL_CTRL1_EG_PORT_BUF_EN | |
| QCA8K_PORT_HOL_CTRL1_WRED_EN, |
| mask); |
| } |
| |
| /* Set initial MTU for every port. |
| * We have only have a general MTU setting. So track |
| * every port and set the max across all port. |
| * Set per port MTU to 1500 as the MTU change function |
| * will add the overhead and if its set to 1518 then it |
| * will apply the overhead again and we will end up with |
| * MTU of 1536 instead of 1518 |
| */ |
| priv->port_mtu[i] = ETH_DATA_LEN; |
| } |
| |
| /* Special GLOBAL_FC_THRESH value are needed for ar8327 switch */ |
| if (priv->switch_id == QCA8K_ID_QCA8327) { |
| mask = QCA8K_GLOBAL_FC_GOL_XON_THRES(288) | |
| QCA8K_GLOBAL_FC_GOL_XOFF_THRES(496); |
| qca8k_rmw(priv, QCA8K_REG_GLOBAL_FC_THRESH, |
| QCA8K_GLOBAL_FC_GOL_XON_THRES_MASK | |
| QCA8K_GLOBAL_FC_GOL_XOFF_THRES_MASK, |
| mask); |
| } |
| |
| /* Setup our port MTUs to match power on defaults */ |
| ret = qca8k_write(priv, QCA8K_MAX_FRAME_SIZE, ETH_FRAME_LEN + ETH_FCS_LEN); |
| if (ret) |
| dev_warn(priv->dev, "failed setting MTU settings"); |
| |
| /* Flush the FDB table */ |
| qca8k_fdb_flush(priv); |
| |
| /* We don't have interrupts for link changes, so we need to poll */ |
| ds->pcs_poll = true; |
| |
| /* Set min a max ageing value supported */ |
| ds->ageing_time_min = 7000; |
| ds->ageing_time_max = 458745000; |
| |
| /* Set max number of LAGs supported */ |
| ds->num_lag_ids = QCA8K_NUM_LAGS; |
| |
| return 0; |
| } |
| |
| static void |
| qca8k_mac_config_setup_internal_delay(struct qca8k_priv *priv, int cpu_port_index, |
| u32 reg) |
| { |
| u32 delay, val = 0; |
| int ret; |
| |
| /* Delay can be declared in 3 different way. |
| * Mode to rgmii and internal-delay standard binding defined |
| * rgmii-id or rgmii-tx/rx phy mode set. |
| * The parse logic set a delay different than 0 only when one |
| * of the 3 different way is used. In all other case delay is |
| * not enabled. With ID or TX/RXID delay is enabled and set |
| * to the default and recommended value. |
| */ |
| if (priv->ports_config.rgmii_tx_delay[cpu_port_index]) { |
| delay = priv->ports_config.rgmii_tx_delay[cpu_port_index]; |
| |
| val |= QCA8K_PORT_PAD_RGMII_TX_DELAY(delay) | |
| QCA8K_PORT_PAD_RGMII_TX_DELAY_EN; |
| } |
| |
| if (priv->ports_config.rgmii_rx_delay[cpu_port_index]) { |
| delay = priv->ports_config.rgmii_rx_delay[cpu_port_index]; |
| |
| val |= QCA8K_PORT_PAD_RGMII_RX_DELAY(delay) | |
| QCA8K_PORT_PAD_RGMII_RX_DELAY_EN; |
| } |
| |
| /* Set RGMII delay based on the selected values */ |
| ret = qca8k_rmw(priv, reg, |
| QCA8K_PORT_PAD_RGMII_TX_DELAY_MASK | |
| QCA8K_PORT_PAD_RGMII_RX_DELAY_MASK | |
| QCA8K_PORT_PAD_RGMII_TX_DELAY_EN | |
| QCA8K_PORT_PAD_RGMII_RX_DELAY_EN, |
| val); |
| if (ret) |
| dev_err(priv->dev, "Failed to set internal delay for CPU port%d", |
| cpu_port_index == QCA8K_CPU_PORT0 ? 0 : 6); |
| } |
| |
| static void |
| qca8k_phylink_mac_config(struct dsa_switch *ds, int port, unsigned int mode, |
| const struct phylink_link_state *state) |
| { |
| struct qca8k_priv *priv = ds->priv; |
| int cpu_port_index, ret; |
| u32 reg, val; |
| |
| switch (port) { |
| case 0: /* 1st CPU port */ |
| if (state->interface != PHY_INTERFACE_MODE_RGMII && |
| state->interface != PHY_INTERFACE_MODE_RGMII_ID && |
| state->interface != PHY_INTERFACE_MODE_RGMII_TXID && |
| state->interface != PHY_INTERFACE_MODE_RGMII_RXID && |
| state->interface != PHY_INTERFACE_MODE_SGMII) |
| return; |
| |
| reg = QCA8K_REG_PORT0_PAD_CTRL; |
| cpu_port_index = QCA8K_CPU_PORT0; |
| break; |
| case 1: |
| case 2: |
| case 3: |
| case 4: |
| case 5: |
| /* Internal PHY, nothing to do */ |
| return; |
| case 6: /* 2nd CPU port / external PHY */ |
| if (state->interface != PHY_INTERFACE_MODE_RGMII && |
| state->interface != PHY_INTERFACE_MODE_RGMII_ID && |
| state->interface != PHY_INTERFACE_MODE_RGMII_TXID && |
| state->interface != PHY_INTERFACE_MODE_RGMII_RXID && |
| state->interface != PHY_INTERFACE_MODE_SGMII && |
| state->interface != PHY_INTERFACE_MODE_1000BASEX) |
| return; |
| |
| reg = QCA8K_REG_PORT6_PAD_CTRL; |
| cpu_port_index = QCA8K_CPU_PORT6; |
| break; |
| default: |
| dev_err(ds->dev, "%s: unsupported port: %i\n", __func__, port); |
| return; |
| } |
| |
| if (port != 6 && phylink_autoneg_inband(mode)) { |
| dev_err(ds->dev, "%s: in-band negotiation unsupported\n", |
| __func__); |
| return; |
| } |
| |
| switch (state->interface) { |
| case PHY_INTERFACE_MODE_RGMII: |
| case PHY_INTERFACE_MODE_RGMII_ID: |
| case PHY_INTERFACE_MODE_RGMII_TXID: |
| case PHY_INTERFACE_MODE_RGMII_RXID: |
| qca8k_write(priv, reg, QCA8K_PORT_PAD_RGMII_EN); |
| |
| /* Configure rgmii delay */ |
| qca8k_mac_config_setup_internal_delay(priv, cpu_port_index, reg); |
| |
| /* QCA8337 requires to set rgmii rx delay for all ports. |
| * This is enabled through PORT5_PAD_CTRL for all ports, |
| * rather than individual port registers. |
| */ |
| if (priv->switch_id == QCA8K_ID_QCA8337) |
| qca8k_write(priv, QCA8K_REG_PORT5_PAD_CTRL, |
| QCA8K_PORT_PAD_RGMII_RX_DELAY_EN); |
| break; |
| case PHY_INTERFACE_MODE_SGMII: |
| case PHY_INTERFACE_MODE_1000BASEX: |
| /* Enable SGMII on the port */ |
| qca8k_write(priv, reg, QCA8K_PORT_PAD_SGMII_EN); |
| |
| /* Enable/disable SerDes auto-negotiation as necessary */ |
| ret = qca8k_read(priv, QCA8K_REG_PWS, &val); |
| if (ret) |
| return; |
| if (phylink_autoneg_inband(mode)) |
| val &= ~QCA8K_PWS_SERDES_AEN_DIS; |
| else |
| val |= QCA8K_PWS_SERDES_AEN_DIS; |
| qca8k_write(priv, QCA8K_REG_PWS, val); |
| |
| /* Configure the SGMII parameters */ |
| ret = qca8k_read(priv, QCA8K_REG_SGMII_CTRL, &val); |
| if (ret) |
| return; |
| |
| val |= QCA8K_SGMII_EN_SD; |
| |
| if (priv->ports_config.sgmii_enable_pll) |
| val |= QCA8K_SGMII_EN_PLL | QCA8K_SGMII_EN_RX | |
| QCA8K_SGMII_EN_TX; |
| |
| if (dsa_is_cpu_port(ds, port)) { |
| /* CPU port, we're talking to the CPU MAC, be a PHY */ |
| val &= ~QCA8K_SGMII_MODE_CTRL_MASK; |
| val |= QCA8K_SGMII_MODE_CTRL_PHY; |
| } else if (state->interface == PHY_INTERFACE_MODE_SGMII) { |
| val &= ~QCA8K_SGMII_MODE_CTRL_MASK; |
| val |= QCA8K_SGMII_MODE_CTRL_MAC; |
| } else if (state->interface == PHY_INTERFACE_MODE_1000BASEX) { |
| val &= ~QCA8K_SGMII_MODE_CTRL_MASK; |
| val |= QCA8K_SGMII_MODE_CTRL_BASEX; |
| } |
| |
| qca8k_write(priv, QCA8K_REG_SGMII_CTRL, val); |
| |
| /* From original code is reported port instability as SGMII also |
| * require delay set. Apply advised values here or take them from DT. |
| */ |
| if (state->interface == PHY_INTERFACE_MODE_SGMII) |
| qca8k_mac_config_setup_internal_delay(priv, cpu_port_index, reg); |
| |
| /* For qca8327/qca8328/qca8334/qca8338 sgmii is unique and |
| * falling edge is set writing in the PORT0 PAD reg |
| */ |
| if (priv->switch_id == QCA8K_ID_QCA8327 || |
| priv->switch_id == QCA8K_ID_QCA8337) |
| reg = QCA8K_REG_PORT0_PAD_CTRL; |
| |
| val = 0; |
| |
| /* SGMII Clock phase configuration */ |
| if (priv->ports_config.sgmii_rx_clk_falling_edge) |
| val |= QCA8K_PORT0_PAD_SGMII_RXCLK_FALLING_EDGE; |
| |
| if (priv->ports_config.sgmii_tx_clk_falling_edge) |
| val |= QCA8K_PORT0_PAD_SGMII_TXCLK_FALLING_EDGE; |
| |
| if (val) |
| ret = qca8k_rmw(priv, reg, |
| QCA8K_PORT0_PAD_SGMII_RXCLK_FALLING_EDGE | |
| QCA8K_PORT0_PAD_SGMII_TXCLK_FALLING_EDGE, |
| val); |
| |
| break; |
| default: |
| dev_err(ds->dev, "xMII mode %s not supported for port %d\n", |
| phy_modes(state->interface), port); |
| return; |
| } |
| } |
| |
| static void |
| qca8k_phylink_validate(struct dsa_switch *ds, int port, |
| unsigned long *supported, |
| struct phylink_link_state *state) |
| { |
| __ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, }; |
| |
| switch (port) { |
| case 0: /* 1st CPU port */ |
| if (state->interface != PHY_INTERFACE_MODE_NA && |
| state->interface != PHY_INTERFACE_MODE_RGMII && |
| state->interface != PHY_INTERFACE_MODE_RGMII_ID && |
| state->interface != PHY_INTERFACE_MODE_RGMII_TXID && |
| state->interface != PHY_INTERFACE_MODE_RGMII_RXID && |
| state->interface != PHY_INTERFACE_MODE_SGMII) |
| goto unsupported; |
| break; |
| case 1: |
| case 2: |
| case 3: |
| case 4: |
| case 5: |
| /* Internal PHY */ |
| if (state->interface != PHY_INTERFACE_MODE_NA && |
| state->interface != PHY_INTERFACE_MODE_GMII && |
| state->interface != PHY_INTERFACE_MODE_INTERNAL) |
| goto unsupported; |
| break; |
| case 6: /* 2nd CPU port / external PHY */ |
| if (state->interface != PHY_INTERFACE_MODE_NA && |
| state->interface != PHY_INTERFACE_MODE_RGMII && |
| state->interface != PHY_INTERFACE_MODE_RGMII_ID && |
| state->interface != PHY_INTERFACE_MODE_RGMII_TXID && |
| state->interface != PHY_INTERFACE_MODE_RGMII_RXID && |
| state->interface != PHY_INTERFACE_MODE_SGMII && |
| state->interface != PHY_INTERFACE_MODE_1000BASEX) |
| goto unsupported; |
| break; |
| default: |
| unsupported: |
| linkmode_zero(supported); |
| return; |
| } |
| |
| phylink_set_port_modes(mask); |
| phylink_set(mask, Autoneg); |
| |
| phylink_set(mask, 1000baseT_Full); |
| phylink_set(mask, 10baseT_Half); |
| phylink_set(mask, 10baseT_Full); |
| phylink_set(mask, 100baseT_Half); |
| phylink_set(mask, 100baseT_Full); |
| |
| if (state->interface == PHY_INTERFACE_MODE_1000BASEX) |
| phylink_set(mask, 1000baseX_Full); |
| |
| phylink_set(mask, Pause); |
| phylink_set(mask, Asym_Pause); |
| |
| linkmode_and(supported, supported, mask); |
| linkmode_and(state->advertising, state->advertising, mask); |
| } |
| |
| static int |
| qca8k_phylink_mac_link_state(struct dsa_switch *ds, int port, |
| struct phylink_link_state *state) |
| { |
| struct qca8k_priv *priv = ds->priv; |
| u32 reg; |
| int ret; |
| |
| ret = qca8k_read(priv, QCA8K_REG_PORT_STATUS(port), ®); |
| if (ret < 0) |
| return ret; |
| |
| state->link = !!(reg & QCA8K_PORT_STATUS_LINK_UP); |
| state->an_complete = state->link; |
| state->an_enabled = !!(reg & QCA8K_PORT_STATUS_LINK_AUTO); |
| state->duplex = (reg & QCA8K_PORT_STATUS_DUPLEX) ? DUPLEX_FULL : |
| DUPLEX_HALF; |
| |
| switch (reg & QCA8K_PORT_STATUS_SPEED) { |
| case QCA8K_PORT_STATUS_SPEED_10: |
| state->speed = SPEED_10; |
| break; |
| case QCA8K_PORT_STATUS_SPEED_100: |
| state->speed = SPEED_100; |
| break; |
| case QCA8K_PORT_STATUS_SPEED_1000: |
| state->speed = SPEED_1000; |
| break; |
| default: |
| state->speed = SPEED_UNKNOWN; |
| break; |
| } |
| |
| state->pause = MLO_PAUSE_NONE; |
| if (reg & QCA8K_PORT_STATUS_RXFLOW) |
| state->pause |= MLO_PAUSE_RX; |
| if (reg & QCA8K_PORT_STATUS_TXFLOW) |
| state->pause |= MLO_PAUSE_TX; |
| |
| return 1; |
| } |
| |
| static void |
| qca8k_phylink_mac_link_down(struct dsa_switch *ds, int port, unsigned int mode, |
| phy_interface_t interface) |
| { |
| struct qca8k_priv *priv = ds->priv; |
| |
| qca8k_port_set_status(priv, port, 0); |
| } |
| |
| static void |
| qca8k_phylink_mac_link_up(struct dsa_switch *ds, int port, unsigned int mode, |
| phy_interface_t interface, struct phy_device *phydev, |
| int speed, int duplex, bool tx_pause, bool rx_pause) |
| { |
| struct qca8k_priv *priv = ds->priv; |
| u32 reg; |
| |
| if (phylink_autoneg_inband(mode)) { |
| reg = QCA8K_PORT_STATUS_LINK_AUTO; |
| } else { |
| switch (speed) { |
| case SPEED_10: |
| reg = QCA8K_PORT_STATUS_SPEED_10; |
| break; |
| case SPEED_100: |
| reg = QCA8K_PORT_STATUS_SPEED_100; |
| break; |
| case SPEED_1000: |
| reg = QCA8K_PORT_STATUS_SPEED_1000; |
| break; |
| default: |
| reg = QCA8K_PORT_STATUS_LINK_AUTO; |
| break; |
| } |
| |
| if (duplex == DUPLEX_FULL) |
| reg |= QCA8K_PORT_STATUS_DUPLEX; |
| |
| if (rx_pause || dsa_is_cpu_port(ds, port)) |
| reg |= QCA8K_PORT_STATUS_RXFLOW; |
| |
| if (tx_pause || dsa_is_cpu_port(ds, port)) |
| reg |= QCA8K_PORT_STATUS_TXFLOW; |
| } |
| |
| reg |= QCA8K_PORT_STATUS_TXMAC | QCA8K_PORT_STATUS_RXMAC; |
| |
| qca8k_write(priv, QCA8K_REG_PORT_STATUS(port), reg); |
| } |
| |
| static void |
| qca8k_get_strings(struct dsa_switch *ds, int port, u32 stringset, uint8_t *data) |
| { |
| const struct qca8k_match_data *match_data; |
| struct qca8k_priv *priv = ds->priv; |
| int i; |
| |
| if (stringset != ETH_SS_STATS) |
| return; |
| |
| match_data = of_device_get_match_data(priv->dev); |
| |
| for (i = 0; i < match_data->mib_count; i++) |
| strncpy(data + i * ETH_GSTRING_LEN, ar8327_mib[i].name, |
| ETH_GSTRING_LEN); |
| } |
| |
| static void |
| qca8k_get_ethtool_stats(struct dsa_switch *ds, int port, |
| uint64_t *data) |
| { |
| struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; |
| const struct qca8k_match_data *match_data; |
| const struct qca8k_mib_desc *mib; |
| u32 reg, i, val; |
| u32 hi = 0; |
| int ret; |
| |
| match_data = of_device_get_match_data(priv->dev); |
| |
| for (i = 0; i < match_data->mib_count; i++) { |
| mib = &ar8327_mib[i]; |
| reg = QCA8K_PORT_MIB_COUNTER(port) + mib->offset; |
| |
| ret = qca8k_read(priv, reg, &val); |
| if (ret < 0) |
| continue; |
| |
| if (mib->size == 2) { |
| ret = qca8k_read(priv, reg + 4, &hi); |
| if (ret < 0) |
| continue; |
| } |
| |
| data[i] = val; |
| if (mib->size == 2) |
| data[i] |= (u64)hi << 32; |
| } |
| } |
| |
| static int |
| qca8k_get_sset_count(struct dsa_switch *ds, int port, int sset) |
| { |
| const struct qca8k_match_data *match_data; |
| struct qca8k_priv *priv = ds->priv; |
| |
| if (sset != ETH_SS_STATS) |
| return 0; |
| |
| match_data = of_device_get_match_data(priv->dev); |
| |
| return match_data->mib_count; |
| } |
| |
| static int |
| qca8k_set_mac_eee(struct dsa_switch *ds, int port, struct ethtool_eee *eee) |
| { |
| struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; |
| u32 lpi_en = QCA8K_REG_EEE_CTRL_LPI_EN(port); |
| u32 reg; |
| int ret; |
| |
| mutex_lock(&priv->reg_mutex); |
| ret = qca8k_read(priv, QCA8K_REG_EEE_CTRL, ®); |
| if (ret < 0) |
| goto exit; |
| |
| if (eee->eee_enabled) |
| reg |= lpi_en; |
| else |
| reg &= ~lpi_en; |
| ret = qca8k_write(priv, QCA8K_REG_EEE_CTRL, reg); |
| |
| exit: |
| mutex_unlock(&priv->reg_mutex); |
| return ret; |
| } |
| |
| static int |
| qca8k_get_mac_eee(struct dsa_switch *ds, int port, struct ethtool_eee *e) |
| { |
| /* Nothing to do on the port's MAC */ |
| return 0; |
| } |
| |
| static void |
| qca8k_port_stp_state_set(struct dsa_switch *ds, int port, u8 state) |
| { |
| struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; |
| u32 stp_state; |
| |
| switch (state) { |
| case BR_STATE_DISABLED: |
| stp_state = QCA8K_PORT_LOOKUP_STATE_DISABLED; |
| break; |
| case BR_STATE_BLOCKING: |
| stp_state = QCA8K_PORT_LOOKUP_STATE_BLOCKING; |
| break; |
| case BR_STATE_LISTENING: |
| stp_state = QCA8K_PORT_LOOKUP_STATE_LISTENING; |
| break; |
| case BR_STATE_LEARNING: |
| stp_state = QCA8K_PORT_LOOKUP_STATE_LEARNING; |
| break; |
| case BR_STATE_FORWARDING: |
| default: |
| stp_state = QCA8K_PORT_LOOKUP_STATE_FORWARD; |
| break; |
| } |
| |
| qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(port), |
| QCA8K_PORT_LOOKUP_STATE_MASK, stp_state); |
| } |
| |
| static int |
| qca8k_port_bridge_join(struct dsa_switch *ds, int port, struct net_device *br) |
| { |
| struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; |
| int port_mask, cpu_port; |
| int i, ret; |
| |
| cpu_port = dsa_to_port(ds, port)->cpu_dp->index; |
| port_mask = BIT(cpu_port); |
| |
| for (i = 0; i < QCA8K_NUM_PORTS; i++) { |
| if (dsa_is_cpu_port(ds, i)) |
| continue; |
| if (dsa_to_port(ds, i)->bridge_dev != br) |
| continue; |
| /* Add this port to the portvlan mask of the other ports |
| * in the bridge |
| */ |
| ret = regmap_set_bits(priv->regmap, |
| QCA8K_PORT_LOOKUP_CTRL(i), |
| BIT(port)); |
| if (ret) |
| return ret; |
| if (i != port) |
| port_mask |= BIT(i); |
| } |
| |
| /* Add all other ports to this ports portvlan mask */ |
| ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(port), |
| QCA8K_PORT_LOOKUP_MEMBER, port_mask); |
| |
| return ret; |
| } |
| |
| static void |
| qca8k_port_bridge_leave(struct dsa_switch *ds, int port, struct net_device *br) |
| { |
| struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; |
| int cpu_port, i; |
| |
| cpu_port = dsa_to_port(ds, port)->cpu_dp->index; |
| |
| for (i = 0; i < QCA8K_NUM_PORTS; i++) { |
| if (dsa_is_cpu_port(ds, i)) |
| continue; |
| if (dsa_to_port(ds, i)->bridge_dev != br) |
| continue; |
| /* Remove this port to the portvlan mask of the other ports |
| * in the bridge |
| */ |
| regmap_clear_bits(priv->regmap, |
| QCA8K_PORT_LOOKUP_CTRL(i), |
| BIT(port)); |
| } |
| |
| /* Set the cpu port to be the only one in the portvlan mask of |
| * this port |
| */ |
| qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(port), |
| QCA8K_PORT_LOOKUP_MEMBER, BIT(cpu_port)); |
| } |
| |
| static void |
| qca8k_port_fast_age(struct dsa_switch *ds, int port) |
| { |
| struct qca8k_priv *priv = ds->priv; |
| |
| mutex_lock(&priv->reg_mutex); |
| qca8k_fdb_access(priv, QCA8K_FDB_FLUSH_PORT, port); |
| mutex_unlock(&priv->reg_mutex); |
| } |
| |
| static int |
| qca8k_set_ageing_time(struct dsa_switch *ds, unsigned int msecs) |
| { |
| struct qca8k_priv *priv = ds->priv; |
| unsigned int secs = msecs / 1000; |
| u32 val; |
| |
| /* AGE_TIME reg is set in 7s step */ |
| val = secs / 7; |
| |
| /* Handle case with 0 as val to NOT disable |
| * learning |
| */ |
| if (!val) |
| val = 1; |
| |
| return regmap_update_bits(priv->regmap, QCA8K_REG_ATU_CTRL, QCA8K_ATU_AGE_TIME_MASK, |
| QCA8K_ATU_AGE_TIME(val)); |
| } |
| |
| static int |
| qca8k_port_enable(struct dsa_switch *ds, int port, |
| struct phy_device *phy) |
| { |
| struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; |
| |
| qca8k_port_set_status(priv, port, 1); |
| priv->port_sts[port].enabled = 1; |
| |
| if (dsa_is_user_port(ds, port)) |
| phy_support_asym_pause(phy); |
| |
| return 0; |
| } |
| |
| static void |
| qca8k_port_disable(struct dsa_switch *ds, int port) |
| { |
| struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; |
| |
| qca8k_port_set_status(priv, port, 0); |
| priv->port_sts[port].enabled = 0; |
| } |
| |
| static int |
| qca8k_port_change_mtu(struct dsa_switch *ds, int port, int new_mtu) |
| { |
| struct qca8k_priv *priv = ds->priv; |
| int i, mtu = 0; |
| |
| priv->port_mtu[port] = new_mtu; |
| |
| for (i = 0; i < QCA8K_NUM_PORTS; i++) |
| if (priv->port_mtu[i] > mtu) |
| mtu = priv->port_mtu[i]; |
| |
| /* Include L2 header / FCS length */ |
| return qca8k_write(priv, QCA8K_MAX_FRAME_SIZE, mtu + ETH_HLEN + ETH_FCS_LEN); |
| } |
| |
| static int |
| qca8k_port_max_mtu(struct dsa_switch *ds, int port) |
| { |
| return QCA8K_MAX_MTU; |
| } |
| |
| static int |
| qca8k_port_fdb_insert(struct qca8k_priv *priv, const u8 *addr, |
| u16 port_mask, u16 vid) |
| { |
| /* Set the vid to the port vlan id if no vid is set */ |
| if (!vid) |
| vid = QCA8K_PORT_VID_DEF; |
| |
| return qca8k_fdb_add(priv, addr, port_mask, vid, |
| QCA8K_ATU_STATUS_STATIC); |
| } |
| |
| static int |
| qca8k_port_fdb_add(struct dsa_switch *ds, int port, |
| const unsigned char *addr, u16 vid) |
| { |
| struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; |
| u16 port_mask = BIT(port); |
| |
| return qca8k_port_fdb_insert(priv, addr, port_mask, vid); |
| } |
| |
| static int |
| qca8k_port_fdb_del(struct dsa_switch *ds, int port, |
| const unsigned char *addr, u16 vid) |
| { |
| struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; |
| u16 port_mask = BIT(port); |
| |
| if (!vid) |
| vid = QCA8K_PORT_VID_DEF; |
| |
| return qca8k_fdb_del(priv, addr, port_mask, vid); |
| } |
| |
| static int |
| qca8k_port_fdb_dump(struct dsa_switch *ds, int port, |
| dsa_fdb_dump_cb_t *cb, void *data) |
| { |
| struct qca8k_priv *priv = (struct qca8k_priv *)ds->priv; |
| struct qca8k_fdb _fdb = { 0 }; |
| int cnt = QCA8K_NUM_FDB_RECORDS; |
| bool is_static; |
| int ret = 0; |
| |
| mutex_lock(&priv->reg_mutex); |
| while (cnt-- && !qca8k_fdb_next(priv, &_fdb, port)) { |
| if (!_fdb.aging) |
| break; |
| is_static = (_fdb.aging == QCA8K_ATU_STATUS_STATIC); |
| ret = cb(_fdb.mac, _fdb.vid, is_static, data); |
| if (ret) |
| break; |
| } |
| mutex_unlock(&priv->reg_mutex); |
| |
| return 0; |
| } |
| |
| static int |
| qca8k_port_mdb_add(struct dsa_switch *ds, int port, |
| const struct switchdev_obj_port_mdb *mdb) |
| { |
| struct qca8k_priv *priv = ds->priv; |
| const u8 *addr = mdb->addr; |
| u16 vid = mdb->vid; |
| |
| return qca8k_fdb_search_and_insert(priv, BIT(port), addr, vid); |
| } |
| |
| static int |
| qca8k_port_mdb_del(struct dsa_switch *ds, int port, |
| const struct switchdev_obj_port_mdb *mdb) |
| { |
| struct qca8k_priv *priv = ds->priv; |
| const u8 *addr = mdb->addr; |
| u16 vid = mdb->vid; |
| |
| return qca8k_fdb_search_and_del(priv, BIT(port), addr, vid); |
| } |
| |
| static int |
| qca8k_port_mirror_add(struct dsa_switch *ds, int port, |
| struct dsa_mall_mirror_tc_entry *mirror, |
| bool ingress) |
| { |
| struct qca8k_priv *priv = ds->priv; |
| int monitor_port, ret; |
| u32 reg, val; |
| |
| /* Check for existent entry */ |
| if ((ingress ? priv->mirror_rx : priv->mirror_tx) & BIT(port)) |
| return -EEXIST; |
| |
| ret = regmap_read(priv->regmap, QCA8K_REG_GLOBAL_FW_CTRL0, &val); |
| if (ret) |
| return ret; |
| |
| /* QCA83xx can have only one port set to mirror mode. |
| * Check that the correct port is requested and return error otherwise. |
| * When no mirror port is set, the values is set to 0xF |
| */ |
| monitor_port = FIELD_GET(QCA8K_GLOBAL_FW_CTRL0_MIRROR_PORT_NUM, val); |
| if (monitor_port != 0xF && monitor_port != mirror->to_local_port) |
| return -EEXIST; |
| |
| /* Set the monitor port */ |
| val = FIELD_PREP(QCA8K_GLOBAL_FW_CTRL0_MIRROR_PORT_NUM, |
| mirror->to_local_port); |
| ret = regmap_update_bits(priv->regmap, QCA8K_REG_GLOBAL_FW_CTRL0, |
| QCA8K_GLOBAL_FW_CTRL0_MIRROR_PORT_NUM, val); |
| if (ret) |
| return ret; |
| |
| if (ingress) { |
| reg = QCA8K_PORT_LOOKUP_CTRL(port); |
| val = QCA8K_PORT_LOOKUP_ING_MIRROR_EN; |
| } else { |
| reg = QCA8K_REG_PORT_HOL_CTRL1(port); |
| val = QCA8K_PORT_HOL_CTRL1_EG_MIRROR_EN; |
| } |
| |
| ret = regmap_update_bits(priv->regmap, reg, val, val); |
| if (ret) |
| return ret; |
| |
| /* Track mirror port for tx and rx to decide when the |
| * mirror port has to be disabled. |
| */ |
| if (ingress) |
| priv->mirror_rx |= BIT(port); |
| else |
| priv->mirror_tx |= BIT(port); |
| |
| return 0; |
| } |
| |
| static void |
| qca8k_port_mirror_del(struct dsa_switch *ds, int port, |
| struct dsa_mall_mirror_tc_entry *mirror) |
| { |
| struct qca8k_priv *priv = ds->priv; |
| u32 reg, val; |
| int ret; |
| |
| if (mirror->ingress) { |
| reg = QCA8K_PORT_LOOKUP_CTRL(port); |
| val = QCA8K_PORT_LOOKUP_ING_MIRROR_EN; |
| } else { |
| reg = QCA8K_REG_PORT_HOL_CTRL1(port); |
| val = QCA8K_PORT_HOL_CTRL1_EG_MIRROR_EN; |
| } |
| |
| ret = regmap_clear_bits(priv->regmap, reg, val); |
| if (ret) |
| goto err; |
| |
| if (mirror->ingress) |
| priv->mirror_rx &= ~BIT(port); |
| else |
| priv->mirror_tx &= ~BIT(port); |
| |
| /* No port set to send packet to mirror port. Disable mirror port */ |
| if (!priv->mirror_rx && !priv->mirror_tx) { |
| val = FIELD_PREP(QCA8K_GLOBAL_FW_CTRL0_MIRROR_PORT_NUM, 0xF); |
| ret = regmap_update_bits(priv->regmap, QCA8K_REG_GLOBAL_FW_CTRL0, |
| QCA8K_GLOBAL_FW_CTRL0_MIRROR_PORT_NUM, val); |
| if (ret) |
| goto err; |
| } |
| err: |
| dev_err(priv->dev, "Failed to del mirror port from %d", port); |
| } |
| |
| static int |
| qca8k_port_vlan_filtering(struct dsa_switch *ds, int port, bool vlan_filtering, |
| struct netlink_ext_ack *extack) |
| { |
| struct qca8k_priv *priv = ds->priv; |
| int ret; |
| |
| if (vlan_filtering) { |
| ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(port), |
| QCA8K_PORT_LOOKUP_VLAN_MODE_MASK, |
| QCA8K_PORT_LOOKUP_VLAN_MODE_SECURE); |
| } else { |
| ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(port), |
| QCA8K_PORT_LOOKUP_VLAN_MODE_MASK, |
| QCA8K_PORT_LOOKUP_VLAN_MODE_NONE); |
| } |
| |
| return ret; |
| } |
| |
| static int |
| qca8k_port_vlan_add(struct dsa_switch *ds, int port, |
| const struct switchdev_obj_port_vlan *vlan, |
| struct netlink_ext_ack *extack) |
| { |
| bool untagged = vlan->flags & BRIDGE_VLAN_INFO_UNTAGGED; |
| bool pvid = vlan->flags & BRIDGE_VLAN_INFO_PVID; |
| struct qca8k_priv *priv = ds->priv; |
| int ret; |
| |
| ret = qca8k_vlan_add(priv, port, vlan->vid, untagged); |
| if (ret) { |
| dev_err(priv->dev, "Failed to add VLAN to port %d (%d)", port, ret); |
| return ret; |
| } |
| |
| if (pvid) { |
| ret = qca8k_rmw(priv, QCA8K_EGRESS_VLAN(port), |
| QCA8K_EGREES_VLAN_PORT_MASK(port), |
| QCA8K_EGREES_VLAN_PORT(port, vlan->vid)); |
| if (ret) |
| return ret; |
| |
| ret = qca8k_write(priv, QCA8K_REG_PORT_VLAN_CTRL0(port), |
| QCA8K_PORT_VLAN_CVID(vlan->vid) | |
| QCA8K_PORT_VLAN_SVID(vlan->vid)); |
| } |
| |
| return ret; |
| } |
| |
| static int |
| qca8k_port_vlan_del(struct dsa_switch *ds, int port, |
| const struct switchdev_obj_port_vlan *vlan) |
| { |
| struct qca8k_priv *priv = ds->priv; |
| int ret; |
| |
| ret = qca8k_vlan_del(priv, port, vlan->vid); |
| if (ret) |
| dev_err(priv->dev, "Failed to delete VLAN from port %d (%d)", port, ret); |
| |
| return ret; |
| } |
| |
| static u32 qca8k_get_phy_flags(struct dsa_switch *ds, int port) |
| { |
| struct qca8k_priv *priv = ds->priv; |
| |
| /* Communicate to the phy internal driver the switch revision. |
| * Based on the switch revision different values needs to be |
| * set to the dbg and mmd reg on the phy. |
| * The first 2 bit are used to communicate the switch revision |
| * to the phy driver. |
| */ |
| if (port > 0 && port < 6) |
| return priv->switch_revision; |
| |
| return 0; |
| } |
| |
| static enum dsa_tag_protocol |
| qca8k_get_tag_protocol(struct dsa_switch *ds, int port, |
| enum dsa_tag_protocol mp) |
| { |
| return DSA_TAG_PROTO_QCA; |
| } |
| |
| static bool |
| qca8k_lag_can_offload(struct dsa_switch *ds, |
| struct net_device *lag, |
| struct netdev_lag_upper_info *info) |
| { |
| struct dsa_port *dp; |
| int id, members = 0; |
| |
| id = dsa_lag_id(ds->dst, lag); |
| if (id < 0 || id >= ds->num_lag_ids) |
| return false; |
| |
| dsa_lag_foreach_port(dp, ds->dst, lag) |
| /* Includes the port joining the LAG */ |
| members++; |
| |
| if (members > QCA8K_NUM_PORTS_FOR_LAG) |
| return false; |
| |
| if (info->tx_type != NETDEV_LAG_TX_TYPE_HASH) |
| return false; |
| |
| if (info->hash_type != NETDEV_LAG_HASH_L2 && |
| info->hash_type != NETDEV_LAG_HASH_L23) |
| return false; |
| |
| return true; |
| } |
| |
| static int |
| qca8k_lag_setup_hash(struct dsa_switch *ds, |
| struct net_device *lag, |
| struct netdev_lag_upper_info *info) |
| { |
| struct qca8k_priv *priv = ds->priv; |
| bool unique_lag = true; |
| u32 hash = 0; |
| int i, id; |
| |
| id = dsa_lag_id(ds->dst, lag); |
| |
| switch (info->hash_type) { |
| case NETDEV_LAG_HASH_L23: |
| hash |= QCA8K_TRUNK_HASH_SIP_EN; |
| hash |= QCA8K_TRUNK_HASH_DIP_EN; |
| fallthrough; |
| case NETDEV_LAG_HASH_L2: |
| hash |= QCA8K_TRUNK_HASH_SA_EN; |
| hash |= QCA8K_TRUNK_HASH_DA_EN; |
| break; |
| default: /* We should NEVER reach this */ |
| return -EOPNOTSUPP; |
| } |
| |
| /* Check if we are the unique configured LAG */ |
| dsa_lags_foreach_id(i, ds->dst) |
| if (i != id && dsa_lag_dev(ds->dst, i)) { |
| unique_lag = false; |
| break; |
| } |
| |
| /* Hash Mode is global. Make sure the same Hash Mode |
| * is set to all the 4 possible lag. |
| * If we are the unique LAG we can set whatever hash |
| * mode we want. |
| * To change hash mode it's needed to remove all LAG |
| * and change the mode with the latest. |
| */ |
| if (unique_lag) { |
| priv->lag_hash_mode = hash; |
| } else if (priv->lag_hash_mode != hash) { |
| netdev_err(lag, "Error: Mismatched Hash Mode across different lag is not supported\n"); |
| return -EOPNOTSUPP; |
| } |
| |
| return regmap_update_bits(priv->regmap, QCA8K_TRUNK_HASH_EN_CTRL, |
| QCA8K_TRUNK_HASH_MASK, hash); |
| } |
| |
| static int |
| qca8k_lag_refresh_portmap(struct dsa_switch *ds, int port, |
| struct net_device *lag, bool delete) |
| { |
| struct qca8k_priv *priv = ds->priv; |
| int ret, id, i; |
| u32 val; |
| |
| id = dsa_lag_id(ds->dst, lag); |
| |
| /* Read current port member */ |
| ret = regmap_read(priv->regmap, QCA8K_REG_GOL_TRUNK_CTRL0, &val); |
| if (ret) |
| return ret; |
| |
| /* Shift val to the correct trunk */ |
| val >>= QCA8K_REG_GOL_TRUNK_SHIFT(id); |
| val &= QCA8K_REG_GOL_TRUNK_MEMBER_MASK; |
| if (delete) |
| val &= ~BIT(port); |
| else |
| val |= BIT(port); |
| |
| /* Update port member. With empty portmap disable trunk */ |
| ret = regmap_update_bits(priv->regmap, QCA8K_REG_GOL_TRUNK_CTRL0, |
| QCA8K_REG_GOL_TRUNK_MEMBER(id) | |
| QCA8K_REG_GOL_TRUNK_EN(id), |
| !val << QCA8K_REG_GOL_TRUNK_SHIFT(id) | |
| val << QCA8K_REG_GOL_TRUNK_SHIFT(id)); |
| |
| /* Search empty member if adding or port on deleting */ |
| for (i = 0; i < QCA8K_NUM_PORTS_FOR_LAG; i++) { |
| ret = regmap_read(priv->regmap, QCA8K_REG_GOL_TRUNK_CTRL(id), &val); |
| if (ret) |
| return ret; |
| |
| val >>= QCA8K_REG_GOL_TRUNK_ID_MEM_ID_SHIFT(id, i); |
| val &= QCA8K_REG_GOL_TRUNK_ID_MEM_ID_MASK; |
| |
| if (delete) { |
| /* If port flagged to be disabled assume this member is |
| * empty |
| */ |
| if (val != QCA8K_REG_GOL_TRUNK_ID_MEM_ID_EN_MASK) |
| continue; |
| |
| val &= QCA8K_REG_GOL_TRUNK_ID_MEM_ID_PORT_MASK; |
| if (val != port) |
| continue; |
| } else { |
| /* If port flagged to be enabled assume this member is |
| * already set |
| */ |
| if (val == QCA8K_REG_GOL_TRUNK_ID_MEM_ID_EN_MASK) |
| continue; |
| } |
| |
| /* We have found the member to add/remove */ |
| break; |
| } |
| |
| /* Set port in the correct port mask or disable port if in delete mode */ |
| return regmap_update_bits(priv->regmap, QCA8K_REG_GOL_TRUNK_CTRL(id), |
| QCA8K_REG_GOL_TRUNK_ID_MEM_ID_EN(id, i) | |
| QCA8K_REG_GOL_TRUNK_ID_MEM_ID_PORT(id, i), |
| !delete << QCA8K_REG_GOL_TRUNK_ID_MEM_ID_SHIFT(id, i) | |
| port << QCA8K_REG_GOL_TRUNK_ID_MEM_ID_SHIFT(id, i)); |
| } |
| |
| static int |
| qca8k_port_lag_join(struct dsa_switch *ds, int port, |
| struct net_device *lag, |
| struct netdev_lag_upper_info *info) |
| { |
| int ret; |
| |
| if (!qca8k_lag_can_offload(ds, lag, info)) |
| return -EOPNOTSUPP; |
| |
| ret = qca8k_lag_setup_hash(ds, lag, info); |
| if (ret) |
| return ret; |
| |
| return qca8k_lag_refresh_portmap(ds, port, lag, false); |
| } |
| |
| static int |
| qca8k_port_lag_leave(struct dsa_switch *ds, int port, |
| struct net_device *lag) |
| { |
| return qca8k_lag_refresh_portmap(ds, port, lag, true); |
| } |
| |
| static const struct dsa_switch_ops qca8k_switch_ops = { |
| .get_tag_protocol = qca8k_get_tag_protocol, |
| .setup = qca8k_setup, |
| .get_strings = qca8k_get_strings, |
| .get_ethtool_stats = qca8k_get_ethtool_stats, |
| .get_sset_count = qca8k_get_sset_count, |
| .set_ageing_time = qca8k_set_ageing_time, |
| .get_mac_eee = qca8k_get_mac_eee, |
| .set_mac_eee = qca8k_set_mac_eee, |
| .port_enable = qca8k_port_enable, |
| .port_disable = qca8k_port_disable, |
| .port_change_mtu = qca8k_port_change_mtu, |
| .port_max_mtu = qca8k_port_max_mtu, |
| .port_stp_state_set = qca8k_port_stp_state_set, |
| .port_bridge_join = qca8k_port_bridge_join, |
| .port_bridge_leave = qca8k_port_bridge_leave, |
| .port_fast_age = qca8k_port_fast_age, |
| .port_fdb_add = qca8k_port_fdb_add, |
| .port_fdb_del = qca8k_port_fdb_del, |
| .port_fdb_dump = qca8k_port_fdb_dump, |
| .port_mdb_add = qca8k_port_mdb_add, |
| .port_mdb_del = qca8k_port_mdb_del, |
| .port_mirror_add = qca8k_port_mirror_add, |
| .port_mirror_del = qca8k_port_mirror_del, |
| .port_vlan_filtering = qca8k_port_vlan_filtering, |
| .port_vlan_add = qca8k_port_vlan_add, |
| .port_vlan_del = qca8k_port_vlan_del, |
| .phylink_validate = qca8k_phylink_validate, |
| .phylink_mac_link_state = qca8k_phylink_mac_link_state, |
| .phylink_mac_config = qca8k_phylink_mac_config, |
| .phylink_mac_link_down = qca8k_phylink_mac_link_down, |
| .phylink_mac_link_up = qca8k_phylink_mac_link_up, |
| .get_phy_flags = qca8k_get_phy_flags, |
| .port_lag_join = qca8k_port_lag_join, |
| .port_lag_leave = qca8k_port_lag_leave, |
| }; |
| |
| static int qca8k_read_switch_id(struct qca8k_priv *priv) |
| { |
| const struct qca8k_match_data *data; |
| u32 val; |
| u8 id; |
| int ret; |
| |
| /* get the switches ID from the compatible */ |
| data = of_device_get_match_data(priv->dev); |
| if (!data) |
| return -ENODEV; |
| |
| ret = qca8k_read(priv, QCA8K_REG_MASK_CTRL, &val); |
| if (ret < 0) |
| return -ENODEV; |
| |
| id = QCA8K_MASK_CTRL_DEVICE_ID(val); |
| if (id != data->id) { |
| dev_err(priv->dev, "Switch id detected %x but expected %x", id, data->id); |
| return -ENODEV; |
| } |
| |
| priv->switch_id = id; |
| |
| /* Save revision to communicate to the internal PHY driver */ |
| priv->switch_revision = QCA8K_MASK_CTRL_REV_ID(val); |
| |
| return 0; |
| } |
| |
| static int |
| qca8k_sw_probe(struct mdio_device *mdiodev) |
| { |
| struct qca8k_priv *priv; |
| int ret; |
| |
| /* allocate the private data struct so that we can probe the switches |
| * ID register |
| */ |
| priv = devm_kzalloc(&mdiodev->dev, sizeof(*priv), GFP_KERNEL); |
| if (!priv) |
| return -ENOMEM; |
| |
| priv->bus = mdiodev->bus; |
| priv->dev = &mdiodev->dev; |
| |
| priv->reset_gpio = devm_gpiod_get_optional(priv->dev, "reset", |
| GPIOD_ASIS); |
| if (IS_ERR(priv->reset_gpio)) |
| return PTR_ERR(priv->reset_gpio); |
| |
| if (priv->reset_gpio) { |
| gpiod_set_value_cansleep(priv->reset_gpio, 1); |
| /* The active low duration must be greater than 10 ms |
| * and checkpatch.pl wants 20 ms. |
| */ |
| msleep(20); |
| gpiod_set_value_cansleep(priv->reset_gpio, 0); |
| } |
| |
| /* Start by setting up the register mapping */ |
| priv->regmap = devm_regmap_init(&mdiodev->dev, NULL, priv, |
| &qca8k_regmap_config); |
| if (IS_ERR(priv->regmap)) { |
| dev_err(priv->dev, "regmap initialization failed"); |
| return PTR_ERR(priv->regmap); |
| } |
| |
| /* Check the detected switch id */ |
| ret = qca8k_read_switch_id(priv); |
| if (ret) |
| return ret; |
| |
| priv->ds = devm_kzalloc(&mdiodev->dev, sizeof(*priv->ds), GFP_KERNEL); |
| if (!priv->ds) |
| return -ENOMEM; |
| |
| priv->ds->dev = &mdiodev->dev; |
| priv->ds->num_ports = QCA8K_NUM_PORTS; |
| priv->ds->priv = priv; |
| priv->ops = qca8k_switch_ops; |
| priv->ds->ops = &priv->ops; |
| mutex_init(&priv->reg_mutex); |
| dev_set_drvdata(&mdiodev->dev, priv); |
| |
| return dsa_register_switch(priv->ds); |
| } |
| |
| static void |
| qca8k_sw_remove(struct mdio_device *mdiodev) |
| { |
| struct qca8k_priv *priv = dev_get_drvdata(&mdiodev->dev); |
| int i; |
| |
| if (!priv) |
| return; |
| |
| for (i = 0; i < QCA8K_NUM_PORTS; i++) |
| qca8k_port_set_status(priv, i, 0); |
| |
| dsa_unregister_switch(priv->ds); |
| |
| dev_set_drvdata(&mdiodev->dev, NULL); |
| } |
| |
| static void qca8k_sw_shutdown(struct mdio_device *mdiodev) |
| { |
| struct qca8k_priv *priv = dev_get_drvdata(&mdiodev->dev); |
| |
| if (!priv) |
| return; |
| |
| dsa_switch_shutdown(priv->ds); |
| |
| dev_set_drvdata(&mdiodev->dev, NULL); |
| } |
| |
| #ifdef CONFIG_PM_SLEEP |
| static void |
| qca8k_set_pm(struct qca8k_priv *priv, int enable) |
| { |
| int i; |
| |
| for (i = 0; i < QCA8K_NUM_PORTS; i++) { |
| if (!priv->port_sts[i].enabled) |
| continue; |
| |
| qca8k_port_set_status(priv, i, enable); |
| } |
| } |
| |
| static int qca8k_suspend(struct device *dev) |
| { |
| struct qca8k_priv *priv = dev_get_drvdata(dev); |
| |
| qca8k_set_pm(priv, 0); |
| |
| return dsa_switch_suspend(priv->ds); |
| } |
| |
| static int qca8k_resume(struct device *dev) |
| { |
| struct qca8k_priv *priv = dev_get_drvdata(dev); |
| |
| qca8k_set_pm(priv, 1); |
| |
| return dsa_switch_resume(priv->ds); |
| } |
| #endif /* CONFIG_PM_SLEEP */ |
| |
| static SIMPLE_DEV_PM_OPS(qca8k_pm_ops, |
| qca8k_suspend, qca8k_resume); |
| |
| static const struct qca8k_match_data qca8327 = { |
| .id = QCA8K_ID_QCA8327, |
| .reduced_package = true, |
| .mib_count = QCA8K_QCA832X_MIB_COUNT, |
| }; |
| |
| static const struct qca8k_match_data qca8328 = { |
| .id = QCA8K_ID_QCA8327, |
| .mib_count = QCA8K_QCA832X_MIB_COUNT, |
| }; |
| |
| static const struct qca8k_match_data qca833x = { |
| .id = QCA8K_ID_QCA8337, |
| .mib_count = QCA8K_QCA833X_MIB_COUNT, |
| }; |
| |
| static const struct of_device_id qca8k_of_match[] = { |
| { .compatible = "qca,qca8327", .data = &qca8327 }, |
| { .compatible = "qca,qca8328", .data = &qca8328 }, |
| { .compatible = "qca,qca8334", .data = &qca833x }, |
| { .compatible = "qca,qca8337", .data = &qca833x }, |
| { /* sentinel */ }, |
| }; |
| |
| static struct mdio_driver qca8kmdio_driver = { |
| .probe = qca8k_sw_probe, |
| .remove = qca8k_sw_remove, |
| .shutdown = qca8k_sw_shutdown, |
| .mdiodrv.driver = { |
| .name = "qca8k", |
| .of_match_table = qca8k_of_match, |
| .pm = &qca8k_pm_ops, |
| }, |
| }; |
| |
| mdio_module_driver(qca8kmdio_driver); |
| |
| MODULE_AUTHOR("Mathieu Olivari, John Crispin <john@phrozen.org>"); |
| MODULE_DESCRIPTION("Driver for QCA8K ethernet switch family"); |
| MODULE_LICENSE("GPL v2"); |
| MODULE_ALIAS("platform:qca8k"); |