drivers/gpu/drm/panel/panel-leadtek-ltk050h3146w.c

// SPDX-License-Identifier: GPL-2.0
/*
 * Copyright (C) 2020 Theobroma Systems Design und Consulting GmbH
 */

#include <linux/delay.h>
#include <linux/gpio/consumer.h>
#include <linux/media-bus-format.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/of_device.h>
#include <linux/regulator/consumer.h>

#include <video/display_timing.h>
#include <video/mipi_display.h>

#include <drm/drm_mipi_dsi.h>
#include <drm/drm_modes.h>
#include <drm/drm_panel.h>
#include <drm/drm_print.h>

struct ltk050h3146w_cmd {
	char cmd;
	char data;
};

struct ltk050h3146w;
struct ltk050h3146w_desc {
	const struct drm_display_mode *mode;
	int (*init)(struct ltk050h3146w *ctx);
};

struct ltk050h3146w {
	struct device *dev;
	struct drm_panel panel;
	struct gpio_desc *reset_gpio;
	struct regulator *vci;
	struct regulator *iovcc;
	const struct ltk050h3146w_desc *panel_desc;
	bool prepared;
};

static const struct ltk050h3146w_cmd page1_cmds[] = {
	{ 0x22, 0x0A }, /* BGR SS GS */
	{ 0x31, 0x00 }, /* column inversion */
	{ 0x53, 0xA2 }, /* VCOM1 */
	{ 0x55, 0xA2 }, /* VCOM2 */
	{ 0x50, 0x81 }, /* VREG1OUT=5V */
	{ 0x51, 0x85 }, /* VREG2OUT=-5V */
	{ 0x62, 0x0D }, /* EQT Time setting */
/*
 * The vendor init selected page 1 here _again_
 * Is this supposed to be page 2?
 */
	{ 0xA0, 0x00 },
	{ 0xA1, 0x1A },
	{ 0xA2, 0x28 },
	{ 0xA3, 0x13 },
	{ 0xA4, 0x16 },
	{ 0xA5, 0x29 },
	{ 0xA6, 0x1D },
	{ 0xA7, 0x1E },
	{ 0xA8, 0x84 },
	{ 0xA9, 0x1C },
	{ 0xAA, 0x28 },
	{ 0xAB, 0x75 },
	{ 0xAC, 0x1A },
	{ 0xAD, 0x19 },
	{ 0xAE, 0x4D },
	{ 0xAF, 0x22 },
	{ 0xB0, 0x28 },
	{ 0xB1, 0x54 },
	{ 0xB2, 0x66 },
	{ 0xB3, 0x39 },
	{ 0xC0, 0x00 },
	{ 0xC1, 0x1A },
	{ 0xC2, 0x28 },
	{ 0xC3, 0x13 },
	{ 0xC4, 0x16 },
	{ 0xC5, 0x29 },
	{ 0xC6, 0x1D },
	{ 0xC7, 0x1E },
	{ 0xC8, 0x84 },
	{ 0xC9, 0x1C },
	{ 0xCA, 0x28 },
	{ 0xCB, 0x75 },
	{ 0xCC, 0x1A },
	{ 0xCD, 0x19 },
	{ 0xCE, 0x4D },
	{ 0xCF, 0x22 },
	{ 0xD0, 0x28 },
	{ 0xD1, 0x54 },
	{ 0xD2, 0x66 },
	{ 0xD3, 0x39 },
};

static const struct ltk050h3146w_cmd page3_cmds[] = {
	{ 0x01, 0x00 },
	{ 0x02, 0x00 },
	{ 0x03, 0x73 },
	{ 0x04, 0x00 },
	{ 0x05, 0x00 },
	{ 0x06, 0x0a },
	{ 0x07, 0x00 },
	{ 0x08, 0x00 },
	{ 0x09, 0x01 },
	{ 0x0a, 0x00 },
	{ 0x0b, 0x00 },
	{ 0x0c, 0x01 },
	{ 0x0d, 0x00 },
	{ 0x0e, 0x00 },
	{ 0x0f, 0x1d },
	{ 0x10, 0x1d },
	{ 0x11, 0x00 },
	{ 0x12, 0x00 },
	{ 0x13, 0x00 },
	{ 0x14, 0x00 },
	{ 0x15, 0x00 },
	{ 0x16, 0x00 },
	{ 0x17, 0x00 },
	{ 0x18, 0x00 },
	{ 0x19, 0x00 },
	{ 0x1a, 0x00 },
	{ 0x1b, 0x00 },
	{ 0x1c, 0x00 },
	{ 0x1d, 0x00 },
	{ 0x1e, 0x40 },
	{ 0x1f, 0x80 },
	{ 0x20, 0x06 },
	{ 0x21, 0x02 },
	{ 0x22, 0x00 },
	{ 0x23, 0x00 },
	{ 0x24, 0x00 },
	{ 0x25, 0x00 },
	{ 0x26, 0x00 },
	{ 0x27, 0x00 },
	{ 0x28, 0x33 },
	{ 0x29, 0x03 },
	{ 0x2a, 0x00 },
	{ 0x2b, 0x00 },
	{ 0x2c, 0x00 },
	{ 0x2d, 0x00 },
	{ 0x2e, 0x00 },
	{ 0x2f, 0x00 },
	{ 0x30, 0x00 },
	{ 0x31, 0x00 },
	{ 0x32, 0x00 },
	{ 0x33, 0x00 },
	{ 0x34, 0x04 },
	{ 0x35, 0x00 },
	{ 0x36, 0x00 },
	{ 0x37, 0x00 },
	{ 0x38, 0x3C },
	{ 0x39, 0x35 },
	{ 0x3A, 0x01 },
	{ 0x3B, 0x40 },
	{ 0x3C, 0x00 },
	{ 0x3D, 0x01 },
	{ 0x3E, 0x00 },
	{ 0x3F, 0x00 },
	{ 0x40, 0x00 },
	{ 0x41, 0x88 },
	{ 0x42, 0x00 },
	{ 0x43, 0x00 },
	{ 0x44, 0x1F },
	{ 0x50, 0x01 },
	{ 0x51, 0x23 },
	{ 0x52, 0x45 },
	{ 0x53, 0x67 },
	{ 0x54, 0x89 },
	{ 0x55, 0xab },
	{ 0x56, 0x01 },
	{ 0x57, 0x23 },
	{ 0x58, 0x45 },
	{ 0x59, 0x67 },
	{ 0x5a, 0x89 },
	{ 0x5b, 0xab },
	{ 0x5c, 0xcd },
	{ 0x5d, 0xef },
	{ 0x5e, 0x11 },
	{ 0x5f, 0x01 },
	{ 0x60, 0x00 },
	{ 0x61, 0x15 },
	{ 0x62, 0x14 },
	{ 0x63, 0x0E },
	{ 0x64, 0x0F },
	{ 0x65, 0x0C },
	{ 0x66, 0x0D },
	{ 0x67, 0x06 },
	{ 0x68, 0x02 },
	{ 0x69, 0x07 },
	{ 0x6a, 0x02 },
	{ 0x6b, 0x02 },
	{ 0x6c, 0x02 },
	{ 0x6d, 0x02 },
	{ 0x6e, 0x02 },
	{ 0x6f, 0x02 },
	{ 0x70, 0x02 },
	{ 0x71, 0x02 },
	{ 0x72, 0x02 },
	{ 0x73, 0x02 },
	{ 0x74, 0x02 },
	{ 0x75, 0x01 },
	{ 0x76, 0x00 },
	{ 0x77, 0x14 },
	{ 0x78, 0x15 },
	{ 0x79, 0x0E },
	{ 0x7a, 0x0F },
	{ 0x7b, 0x0C },
	{ 0x7c, 0x0D },
	{ 0x7d, 0x06 },
	{ 0x7e, 0x02 },
	{ 0x7f, 0x07 },
	{ 0x80, 0x02 },
	{ 0x81, 0x02 },
	{ 0x82, 0x02 },
	{ 0x83, 0x02 },
	{ 0x84, 0x02 },
	{ 0x85, 0x02 },
	{ 0x86, 0x02 },
	{ 0x87, 0x02 },
	{ 0x88, 0x02 },
	{ 0x89, 0x02 },
	{ 0x8A, 0x02 },
};

static const struct ltk050h3146w_cmd page4_cmds[] = {
	{ 0x70, 0x00 },
	{ 0x71, 0x00 },
	{ 0x82, 0x0F }, /* VGH_MOD clamp level=15v */
	{ 0x84, 0x0F }, /* VGH clamp level 15V */
	{ 0x85, 0x0D }, /* VGL clamp level (-10V) */
	{ 0x32, 0xAC },
	{ 0x8C, 0x80 },
	{ 0x3C, 0xF5 },
	{ 0xB5, 0x07 }, /* GAMMA OP */
	{ 0x31, 0x45 }, /* SOURCE OP */
	{ 0x3A, 0x24 }, /* PS_EN OFF */
	{ 0x88, 0x33 }, /* LVD */
};

static inline
struct ltk050h3146w *panel_to_ltk050h3146w(struct drm_panel *panel)
{
	return container_of(panel, struct ltk050h3146w, panel);
}

#define dsi_dcs_write_seq(dsi, cmd, seq...) do {			\
		static const u8 d[] = { seq };				\
		int ret;						\
		ret = mipi_dsi_dcs_write(dsi, cmd, d, ARRAY_SIZE(d));	\
		if (ret < 0)						\
			return ret;					\
	} while (0)

static int ltk050h3146w_init_sequence(struct ltk050h3146w *ctx)
{
	struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
	int ret;

	/*
	 * Init sequence was supplied by the panel vendor without much
	 * documentation.
	 */
	dsi_dcs_write_seq(dsi, 0xdf, 0x93, 0x65, 0xf8);
	dsi_dcs_write_seq(dsi, 0xb0, 0x01, 0x03, 0x02, 0x00, 0x64, 0x06,
			  0x01);
	dsi_dcs_write_seq(dsi, 0xb2, 0x00, 0xb5);
	dsi_dcs_write_seq(dsi, 0xb3, 0x00, 0xb5);
	dsi_dcs_write_seq(dsi, 0xb7, 0x00, 0xbf, 0x00, 0x00, 0xbf, 0x00);

	dsi_dcs_write_seq(dsi, 0xb9, 0x00, 0xc4, 0x23, 0x07);
	dsi_dcs_write_seq(dsi, 0xbb, 0x02, 0x01, 0x24, 0x00, 0x28, 0x0f,
			  0x28, 0x04, 0xcc, 0xcc, 0xcc);
	dsi_dcs_write_seq(dsi, 0xbc, 0x0f, 0x04);
	dsi_dcs_write_seq(dsi, 0xbe, 0x1e, 0xf2);
	dsi_dcs_write_seq(dsi, 0xc0, 0x26, 0x03);
	dsi_dcs_write_seq(dsi, 0xc1, 0x00, 0x12);
	dsi_dcs_write_seq(dsi, 0xc3, 0x04, 0x02, 0x02, 0x76, 0x01, 0x80,
			  0x80);
	dsi_dcs_write_seq(dsi, 0xc4, 0x24, 0x80, 0xb4, 0x81, 0x12, 0x0f,
			  0x16, 0x00, 0x00);
	dsi_dcs_write_seq(dsi, 0xc8, 0x7f, 0x72, 0x67, 0x5d, 0x5d, 0x50,
			  0x56, 0x41, 0x59, 0x57, 0x55, 0x70, 0x5b, 0x5f,
			  0x4f, 0x47, 0x38, 0x23, 0x08, 0x7f, 0x72, 0x67,
			  0x5d, 0x5d, 0x50, 0x56, 0x41, 0x59, 0x57, 0x55,
			  0x70, 0x5b, 0x5f, 0x4f, 0x47, 0x38, 0x23, 0x08);
	dsi_dcs_write_seq(dsi, 0xd0, 0x1e, 0x1f, 0x57, 0x58, 0x48, 0x4a,
			  0x44, 0x46, 0x40, 0x1f, 0x42, 0x1f, 0x1f, 0x1f,
			  0x1f, 0x1f, 0x1f, 0x1f, 0x1f, 0x1f, 0x1f, 0x1f);
	dsi_dcs_write_seq(dsi, 0xd1, 0x1e, 0x1f, 0x57, 0x58, 0x49, 0x4b,
			  0x45, 0x47, 0x41, 0x1f, 0x43, 0x1f, 0x1f, 0x1f,
			  0x1f, 0x1f, 0x1f, 0x1f, 0x1f, 0x1f, 0x1f, 0x1f);
	dsi_dcs_write_seq(dsi, 0xd2, 0x1f, 0x1e, 0x17, 0x18, 0x07, 0x05,
			  0x0b, 0x09, 0x03, 0x1f, 0x01, 0x1f, 0x1f, 0x1f,
			  0x1f, 0x1f, 0x1f, 0x1f, 0x1f, 0x1f, 0x1f, 0x1f);
	dsi_dcs_write_seq(dsi, 0xd3, 0x1f, 0x1e, 0x17, 0x18, 0x06, 0x04,
			  0x0a, 0x08, 0x02, 0x1f, 0x00, 0x1f, 0x1f, 0x1f,
			  0x1f, 0x1f, 0x1f, 0x1f, 0x1f, 0x1f, 0x1f, 0x1f);
	dsi_dcs_write_seq(dsi, 0xd4, 0x00, 0x00, 0x00, 0x0c, 0x06, 0x20,
			  0x01, 0x02, 0x00, 0x60, 0x15, 0xb0, 0x30, 0x03,
			  0x04, 0x00, 0x60, 0x72, 0x0a, 0x00, 0x60, 0x08);
	dsi_dcs_write_seq(dsi, 0xd5, 0x00, 0x06, 0x06, 0x00, 0x30, 0x00,
			  0x00, 0x00, 0x00, 0x00, 0xbc, 0x50, 0x00, 0x05,
			  0x21, 0x00, 0x60);
	dsi_dcs_write_seq(dsi, 0xdd, 0x2c, 0xa3, 0x00);
	dsi_dcs_write_seq(dsi, 0xde, 0x02);
	dsi_dcs_write_seq(dsi, 0xb2, 0x32, 0x1c);
	dsi_dcs_write_seq(dsi, 0xb7, 0x3b, 0x70, 0x00, 0x04);
	dsi_dcs_write_seq(dsi, 0xc1, 0x11);
	dsi_dcs_write_seq(dsi, 0xbb, 0x21, 0x22, 0x23, 0x24, 0x36, 0x37);
	dsi_dcs_write_seq(dsi, 0xc2, 0x20, 0x38, 0x1e, 0x84);
	dsi_dcs_write_seq(dsi, 0xde, 0x00);

	ret = mipi_dsi_dcs_set_tear_on(dsi, 1);
	if (ret < 0) {
		DRM_DEV_ERROR(ctx->dev, "failed to set tear on: %d\n",
			      ret);
		return ret;
	}

	msleep(60);

	return 0;
}

static const struct drm_display_mode ltk050h3146w_mode = {
	.hdisplay	= 720,
	.hsync_start	= 720 + 42,
	.hsync_end	= 720 + 42 + 8,
	.htotal		= 720 + 42 + 8 + 42,
	.vdisplay	= 1280,
	.vsync_start	= 1280 + 12,
	.vsync_end	= 1280 + 12 + 4,
	.vtotal		= 1280 + 12 + 4 + 18,
	.clock		= 64018,
	.width_mm	= 62,
	.height_mm	= 110,
};

static const struct ltk050h3146w_desc ltk050h3146w_data = {
	.mode = &ltk050h3146w_mode,
	.init = ltk050h3146w_init_sequence,
};

static int ltk050h3146w_a2_select_page(struct ltk050h3146w *ctx, int page)
{
	struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
	u8 d[3] = { 0x98, 0x81, page };

	return mipi_dsi_dcs_write(dsi, 0xff, d, ARRAY_SIZE(d));
}

static int ltk050h3146w_a2_write_page(struct ltk050h3146w *ctx, int page,
				      const struct ltk050h3146w_cmd *cmds,
				      int num)
{
	struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
	int i, ret;

	ret = ltk050h3146w_a2_select_page(ctx, page);
	if (ret < 0) {
		DRM_DEV_ERROR(ctx->dev, "failed to select page %d: %d\n",
			      page, ret);
		return ret;
	}

	for (i = 0; i < num; i++) {
		ret = mipi_dsi_generic_write(dsi, &cmds[i],
					     sizeof(struct ltk050h3146w_cmd));
		if (ret < 0) {
			DRM_DEV_ERROR(ctx->dev,
				      "failed to write page %d init cmds: %d\n",
				       page, ret);
			return ret;
		}
	}

	return 0;
}

static int ltk050h3146w_a2_init_sequence(struct ltk050h3146w *ctx)
{
	struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
	int ret;

	/*
	 * Init sequence was supplied by the panel vendor without much
	 * documentation.
	 */
	ret = ltk050h3146w_a2_write_page(ctx, 3, page3_cmds,
					 ARRAY_SIZE(page3_cmds));
	if (ret < 0)
		return ret;

	ret = ltk050h3146w_a2_write_page(ctx, 4, page4_cmds,
					 ARRAY_SIZE(page4_cmds));
	if (ret < 0)
		return ret;

	ret = ltk050h3146w_a2_write_page(ctx, 1, page1_cmds,
					 ARRAY_SIZE(page1_cmds));
	if (ret < 0)
		return ret;

	ret = ltk050h3146w_a2_select_page(ctx, 0);
	if (ret < 0) {
		DRM_DEV_ERROR(ctx->dev, "failed to select page 0: %d\n", ret);
		return ret;
	}

	/* vendor code called this without param, where there should be one */
	ret = mipi_dsi_dcs_set_tear_on(dsi, 0);
	if (ret < 0) {
		DRM_DEV_ERROR(ctx->dev, "failed to set tear on: %d\n",
			      ret);
		return ret;
	}

	msleep(60);

	return 0;
}

static const struct drm_display_mode ltk050h3146w_a2_mode = {
	.hdisplay	= 720,
	.hsync_start	= 720 + 42,
	.hsync_end	= 720 + 42 + 10,
	.htotal		= 720 + 42 + 10 + 60,
	.vdisplay	= 1280,
	.vsync_start	= 1280 + 18,
	.vsync_end	= 1280 + 18 + 4,
	.vtotal		= 1280 + 18 + 4 + 12,
	.clock		= 65595,
	.width_mm	= 62,
	.height_mm	= 110,
};

static const struct ltk050h3146w_desc ltk050h3146w_a2_data = {
	.mode = &ltk050h3146w_a2_mode,
	.init = ltk050h3146w_a2_init_sequence,
};

static int ltk050h3146w_unprepare(struct drm_panel *panel)
{
	struct ltk050h3146w *ctx = panel_to_ltk050h3146w(panel);
	struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
	int ret;

	if (!ctx->prepared)
		return 0;

	ret = mipi_dsi_dcs_set_display_off(dsi);
	if (ret < 0) {
		DRM_DEV_ERROR(ctx->dev, "failed to set display off: %d\n",
			      ret);
		return ret;
	}

	mipi_dsi_dcs_enter_sleep_mode(dsi);
	if (ret < 0) {
		DRM_DEV_ERROR(ctx->dev, "failed to enter sleep mode: %d\n",
			      ret);
		return ret;
	}

	regulator_disable(ctx->iovcc);
	regulator_disable(ctx->vci);

	ctx->prepared = false;

	return 0;
}

static int ltk050h3146w_prepare(struct drm_panel *panel)
{
	struct ltk050h3146w *ctx = panel_to_ltk050h3146w(panel);
	struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
	int ret;

	if (ctx->prepared)
		return 0;

	DRM_DEV_DEBUG_DRIVER(ctx->dev, "Resetting the panel\n");
	ret = regulator_enable(ctx->vci);
	if (ret < 0) {
		DRM_DEV_ERROR(ctx->dev,
			      "Failed to enable vci supply: %d\n", ret);
		return ret;
	}
	ret = regulator_enable(ctx->iovcc);
	if (ret < 0) {
		DRM_DEV_ERROR(ctx->dev,
			      "Failed to enable iovcc supply: %d\n", ret);
		goto disable_vci;
	}

	gpiod_set_value_cansleep(ctx->reset_gpio, 1);
	usleep_range(5000, 6000);
	gpiod_set_value_cansleep(ctx->reset_gpio, 0);
	msleep(20);

	ret = ctx->panel_desc->init(ctx);
	if (ret < 0) {
		DRM_DEV_ERROR(ctx->dev, "Panel init sequence failed: %d\n",
			      ret);
		goto disable_iovcc;
	}

	ret = mipi_dsi_dcs_exit_sleep_mode(dsi);
	if (ret < 0) {
		DRM_DEV_ERROR(ctx->dev, "Failed to exit sleep mode: %d\n", ret);
		goto disable_iovcc;
	}

	/* T9: 120ms */
	msleep(120);

	ret = mipi_dsi_dcs_set_display_on(dsi);
	if (ret < 0) {
		DRM_DEV_ERROR(ctx->dev, "Failed to set display on: %d\n", ret);
		goto disable_iovcc;
	}

	msleep(50);

	ctx->prepared = true;

	return 0;

disable_iovcc:
	regulator_disable(ctx->iovcc);
disable_vci:
	regulator_disable(ctx->vci);
	return ret;
}

static int ltk050h3146w_get_modes(struct drm_panel *panel,
				  struct drm_connector *connector)
{
	struct ltk050h3146w *ctx = panel_to_ltk050h3146w(panel);
	struct drm_display_mode *mode;

	mode = drm_mode_duplicate(connector->dev, ctx->panel_desc->mode);
	if (!mode)
		return -ENOMEM;

	drm_mode_set_name(mode);

	mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED;
	connector->display_info.width_mm = mode->width_mm;
	connector->display_info.height_mm = mode->height_mm;
	drm_mode_probed_add(connector, mode);

	return 1;
}

static const struct drm_panel_funcs ltk050h3146w_funcs = {
	.unprepare	= ltk050h3146w_unprepare,
	.prepare	= ltk050h3146w_prepare,
	.get_modes	= ltk050h3146w_get_modes,
};

static int ltk050h3146w_probe(struct mipi_dsi_device *dsi)
{
	struct device *dev = &dsi->dev;
	struct ltk050h3146w *ctx;
	int ret;

	ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
	if (!ctx)
		return -ENOMEM;

	ctx->panel_desc = of_device_get_match_data(dev);
	if (!ctx->panel_desc)
		return -EINVAL;

	ctx->reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW);
	if (IS_ERR(ctx->reset_gpio)) {
		DRM_DEV_ERROR(dev, "cannot get reset gpio\n");
		return PTR_ERR(ctx->reset_gpio);
	}

	ctx->vci = devm_regulator_get(dev, "vci");
	if (IS_ERR(ctx->vci)) {
		ret = PTR_ERR(ctx->vci);
		if (ret != -EPROBE_DEFER)
			DRM_DEV_ERROR(dev,
				      "Failed to request vci regulator: %d\n",
				      ret);
		return ret;
	}

	ctx->iovcc = devm_regulator_get(dev, "iovcc");
	if (IS_ERR(ctx->iovcc)) {
		ret = PTR_ERR(ctx->iovcc);
		if (ret != -EPROBE_DEFER)
			DRM_DEV_ERROR(dev,
				      "Failed to request iovcc regulator: %d\n",
				      ret);
		return ret;
	}

	mipi_dsi_set_drvdata(dsi, ctx);

	ctx->dev = dev;

	dsi->lanes = 4;
	dsi->format = MIPI_DSI_FMT_RGB888;
	dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST |
			  MIPI_DSI_MODE_LPM | MIPI_DSI_MODE_EOT_PACKET;

	drm_panel_init(&ctx->panel, &dsi->dev, &ltk050h3146w_funcs,
		       DRM_MODE_CONNECTOR_DSI);

	ret = drm_panel_of_backlight(&ctx->panel);
	if (ret)
		return ret;

	drm_panel_add(&ctx->panel);

	ret = mipi_dsi_attach(dsi);
	if (ret < 0) {
		DRM_DEV_ERROR(dev, "mipi_dsi_attach failed: %d\n", ret);
		drm_panel_remove(&ctx->panel);
		return ret;
	}

	return 0;
}

static void ltk050h3146w_shutdown(struct mipi_dsi_device *dsi)
{
	struct ltk050h3146w *ctx = mipi_dsi_get_drvdata(dsi);
	int ret;

	ret = drm_panel_unprepare(&ctx->panel);
	if (ret < 0)
		DRM_DEV_ERROR(&dsi->dev, "Failed to unprepare panel: %d\n",
			      ret);

	ret = drm_panel_disable(&ctx->panel);
	if (ret < 0)
		DRM_DEV_ERROR(&dsi->dev, "Failed to disable panel: %d\n",
			      ret);
}

static int ltk050h3146w_remove(struct mipi_dsi_device *dsi)
{
	struct ltk050h3146w *ctx = mipi_dsi_get_drvdata(dsi);
	int ret;

	ltk050h3146w_shutdown(dsi);

	ret = mipi_dsi_detach(dsi);
	if (ret < 0)
		DRM_DEV_ERROR(&dsi->dev, "Failed to detach from DSI host: %d\n",
			      ret);

	drm_panel_remove(&ctx->panel);

	return 0;
}

static const struct of_device_id ltk050h3146w_of_match[] = {
	{
		.compatible = "leadtek,ltk050h3146w",
		.data = &ltk050h3146w_data,
	},
	{
		.compatible = "leadtek,ltk050h3146w-a2",
		.data = &ltk050h3146w_a2_data,
	},
	{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(of, ltk050h3146w_of_match);

static struct mipi_dsi_driver ltk050h3146w_driver = {
	.driver = {
		.name = "panel-leadtek-ltk050h3146w",
		.of_match_table = ltk050h3146w_of_match,
	},
	.probe	= ltk050h3146w_probe,
	.remove = ltk050h3146w_remove,
	.shutdown = ltk050h3146w_shutdown,
};
module_mipi_dsi_driver(ltk050h3146w_driver);

MODULE_AUTHOR("Heiko Stuebner <heiko.stuebner@theobroma-systems.com>");
MODULE_DESCRIPTION("DRM driver for Leadtek LTK050H3146W MIPI DSI panel");
MODULE_LICENSE("GPL v2");