arch/arm64/boot/dts/renesas/draak.dtsi - linux - Git at Google

 // SPDX-License-Identifier: GPL-2.0
 /*
  * Device Tree Source for the Draak board
  *
  * Copyright (C) 2016-2018 Renesas Electronics Corp.
  * Copyright (C) 2017 Glider bvba
  */

 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>

 / {
 	model = "Renesas Draak board";
 	compatible = "renesas,draak";

 	aliases {
 		serial0 = &scif2;
 		ethernet0 = &avb;
 	};

 	audio_clkout: audio-clkout {
 		/*
 		 * This is same as <&rcar_sound 0>
 		 * but needed to avoid cs2000/rcar_sound probe dead-lock
 		 */
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <12288000>;
 	};

 	backlight: backlight {
 		compatible = "pwm-backlight";
 		pwms = <&pwm1 0 50000>;

 		brightness-levels = <512 511 505 494 473 440 392 327 241 133 0>;
 		default-brightness-level = <10>;

 		power-supply = <&reg_12p0v>;
 		enable-gpios = <&gpio4 0 GPIO_ACTIVE_HIGH>;
 	};

 	chosen {
 		bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
 		stdout-path = "serial0:115200n8";
 	};

 	composite-in {
 		compatible = "composite-video-connector";

 		port {
 			composite_con_in: endpoint {
 				remote-endpoint = <&adv7180_in>;
 			};
 		};
 	};

 	hdmi-in {
 		compatible = "hdmi-connector";
 		type = "a";

 		port {
 			hdmi_con_in: endpoint {
 				remote-endpoint = <&adv7612_in>;
 			};
 		};
 	};

 	hdmi-out {
 		compatible = "hdmi-connector";
 		type = "a";

 		port {
 			hdmi_con_out: endpoint {
 				remote-endpoint = <&adv7511_out>;
 			};
 		};
 	};

 	keys {
 		compatible = "gpio-keys";

 		pinctrl-0 = <&keys_pins>;
 		pinctrl-names = "default";

 		key-1 {
 			gpios = <&gpio4 12 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_1>;
 			label = "SW56-1";
 			wakeup-source;
 			debounce-interval = <20>;
 		};
 		key-2 {
 			gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_2>;
 			label = "SW56-2";
 			wakeup-source;
 			debounce-interval = <20>;
 		};
 		key-3 {
 			gpios = <&gpio4 14 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_3>;
 			label = "SW56-3";
 			wakeup-source;
 			debounce-interval = <20>;
 		};
 		key-4 {
 			gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_4>;
 			label = "SW56-4";
 			wakeup-source;
 			debounce-interval = <20>;
 		};
 	};

 	lvds-decoder {
 		compatible = "thine,thc63lvd1024";
 		vcc-supply = <&reg_3p3v>;

 		ports {
 			#address-cells = <1>;
 			#size-cells = <0>;

 			port@0 {
 				reg = <0>;
 				thc63lvd1024_in: endpoint {
 					remote-endpoint = <&lvds0_out>;
 				};
 			};

 			port@2 {
 				reg = <2>;
 				thc63lvd1024_out: endpoint {
 					remote-endpoint = <&adv7511_in>;
 				};
 			};
 		};
 	};

 	memory@48000000 {
 		device_type = "memory";
 		/* first 128MB is reserved for secure area. */
 		reg = <0x0 0x48000000 0x0 0x18000000>;
 	};

 	reg_1p8v: regulator-1p8v {
 		compatible = "regulator-fixed";
 		regulator-name = "fixed-1.8V";
 		regulator-min-microvolt = <1800000>;
 		regulator-max-microvolt = <1800000>;
 		regulator-boot-on;
 		regulator-always-on;
 	};

 	reg_3p3v: regulator-3p3v {
 		compatible = "regulator-fixed";
 		regulator-name = "fixed-3.3V";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 		regulator-boot-on;
 		regulator-always-on;
 	};

 	reg_12p0v: regulator-12p0v {
 		compatible = "regulator-fixed";
 		regulator-name = "D12.0V";
 		regulator-min-microvolt = <12000000>;
 		regulator-max-microvolt = <12000000>;
 		regulator-boot-on;
 		regulator-always-on;
 	};

 	sound_card: sound {
 		compatible = "audio-graph-card";

 		dais = <&rsnd_port0	/* ak4613 */
 			/* HDMI is not yet supported */
 		>;
 	};

 	vga {
 		compatible = "vga-connector";

 		port {
 			vga_in: endpoint {
 				remote-endpoint = <&adv7123_out>;
 			};
 		};
 	};

 	vga-encoder {
 		compatible = "adi,adv7123";

 		ports {
 			#address-cells = <1>;
 			#size-cells = <0>;

 			port@0 {
 				reg = <0>;
 				adv7123_in: endpoint {
 					remote-endpoint = <&du_out_rgb>;
 				};
 			};
 			port@1 {
 				reg = <1>;
 				adv7123_out: endpoint {
 					remote-endpoint = <&vga_in>;
 				};
 			};
 		};
 	};

 	x12_clk: x12 {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <74250000>;
 	};

 	x19_clk: x19 {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <24576000>;
 	};
 };

 &audio_clk_b {
 	/*
 	 * X11 is connected to VI4_FIELD/SCIF_CLK/AUDIO_CLKB,
 	 * and R-Car Sound uses AUDIO_CLKB.
 	 * Note is that schematic indicates VI4_FIELD conection only
 	 * not AUDIO_CLKB at SoC page.
 	 * And this VI4_FIELD/SCIF_CLK/AUDIO_CLKB is connected to SW60.
 	 * SW60 should be 1-2.
 	 */

 	clock-frequency = <22579200>;
 };

 &avb {
 	pinctrl-0 = <&avb0_pins>;
 	pinctrl-names = "default";
 	renesas,no-ether-link;
 	phy-handle = <&phy0>;
 	status = "okay";

 	phy0: ethernet-phy@0 {
 		compatible = "ethernet-phy-id0022.1622",
 			     "ethernet-phy-ieee802.3-c22";
 		rxc-skew-ps = <1500>;
 		reg = <0>;
 		interrupt-parent = <&gpio5>;
 		interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
 		reset-gpios = <&gpio5 18 GPIO_ACTIVE_LOW>;
 		/*
 		 * TX clock internal delay mode is required for reliable
 		 * 1Gbps communication using the KSZ9031RNX phy present on
 		 * the Draak board, however, TX clock internal delay mode
 		 * isn't supported on R-Car D3(e).  Thus, limit speed to
 		 * 100Mbps for reliable communication.
 		 */
 		max-speed = <100>;
 	};
 };

 &can0 {
 	pinctrl-0 = <&can0_pins>;
 	pinctrl-names = "default";
 	status = "okay";
 };

 &can1 {
 	pinctrl-0 = <&can1_pins>;
 	pinctrl-names = "default";
 	status = "okay";
 };

 &du {
 	pinctrl-0 = <&du_pins>;
 	pinctrl-names = "default";
 	status = "okay";

 	clocks = <&cpg CPG_MOD 724>,
 		 <&cpg CPG_MOD 723>,
 		 <&x12_clk>;
 	clock-names = "du.0", "du.1", "dclkin.0";

 	ports {
 		port@0 {
 			endpoint {
 				remote-endpoint = <&adv7123_in>;
 			};
 		};
 	};
 };

 &ehci0 {
 	dr_mode = "host";
 	status = "okay";
 };

 &extal_clk {
 	clock-frequency = <48000000>;
 };

 &hsusb {
 	dr_mode = "host";
 	status = "okay";
 };

 &i2c0 {
 	pinctrl-0 = <&i2c0_pins>;
 	pinctrl-names = "default";
 	status = "okay";

 	ak4613: codec@10 {
 		compatible = "asahi-kasei,ak4613";
 		#sound-dai-cells = <0>;
 		reg = <0x10>;
 		clocks = <&rcar_sound 0>; /* audio_clkout */

 		asahi-kasei,in1-single-end;
 		asahi-kasei,in2-single-end;
 		asahi-kasei,out1-single-end;
 		asahi-kasei,out2-single-end;
 		asahi-kasei,out3-single-end;
 		asahi-kasei,out4-single-end;
 		asahi-kasei,out5-single-end;
 		asahi-kasei,out6-single-end;

 		port {
 			ak4613_endpoint: endpoint {
 				remote-endpoint = <&rsnd_for_ak4613>;
 			};
 		};
 	};

 	composite-in@20 {
 		compatible = "adi,adv7180cp";
 		reg = <0x20>;

 		ports {
 			#address-cells = <1>;
 			#size-cells = <0>;

 			port@0 {
 				reg = <0>;
 				adv7180_in: endpoint {
 					remote-endpoint = <&composite_con_in>;
 				};
 			};

 			port@3 {
 				reg = <3>;

 				/*
 				 * The VIN4 video input path is shared between
 				 * CVBS and HDMI inputs through SW[49-53]
 				 * switches.
 				 *
 				 * CVBS is the default selection, link it to
 				 * VIN4 here.
 				 */
 				adv7180_out: endpoint {
 					remote-endpoint = <&vin4_in>;
 				};
 			};
 		};

 	};

 	hdmi-encoder@39 {
 		compatible = "adi,adv7511w";
 		reg = <0x39>, <0x3f>, <0x3c>, <0x38>;
 		reg-names = "main", "edid", "cec", "packet";
 		interrupt-parent = <&gpio1>;
 		interrupts = <28 IRQ_TYPE_LEVEL_LOW>;

 		adi,input-depth = <8>;
 		adi,input-colorspace = "rgb";
 		adi,input-clock = "1x";

 		ports {
 			#address-cells = <1>;
 			#size-cells = <0>;

 			port@0 {
 				reg = <0>;
 				adv7511_in: endpoint {
 					remote-endpoint = <&thc63lvd1024_out>;
 				};
 			};

 			port@1 {
 				reg = <1>;
 				adv7511_out: endpoint {
 					remote-endpoint = <&hdmi_con_out>;
 				};
 			};
 		};
 	};

 	hdmi-decoder@4c {
 		compatible = "adi,adv7612";
 		reg = <0x4c>;
 		default-input = <0>;

 		ports {
 			#address-cells = <1>;
 			#size-cells = <0>;

 			port@0 {
 				reg = <0>;

 				adv7612_in: endpoint {
 					remote-endpoint = <&hdmi_con_in>;
 				};
 			};

 			port@2 {
 				reg = <2>;

 				/*
 				 * The VIN4 video input path is shared between
 				 * CVBS and HDMI inputs through SW[49-53]
 				 * switches.
 				 *
 				 * CVBS is the default selection, leave HDMI
 				 * not connected here.
 				 */
 				adv7612_out: endpoint {
 					pclk-sample = <0>;
 					hsync-active = <0>;
 					vsync-active = <0>;
 				};
 			};
 		};
 	};

 	cs2000: clk-multiplier@4f {
 		#clock-cells = <0>;
 		compatible = "cirrus,cs2000-cp";
 		reg = <0x4f>;
 		clocks = <&audio_clkout>, <&x19_clk>; /* audio_clkout_1, x19 */
 		clock-names = "clk_in", "ref_clk";

 		assigned-clocks = <&cs2000>;
 		assigned-clock-rates = <24576000>; /* 1/1 divide */
 	};

 	eeprom@50 {
 		compatible = "rohm,br24t01", "atmel,24c01";
 		reg = <0x50>;
 		pagesize = <8>;
 	};
 };

 &i2c1 {
 	pinctrl-0 = <&i2c1_pins>;
 	pinctrl-names = "default";
 	status = "okay";
 };

 &lvds0 {
 	status = "okay";

 	clocks = <&cpg CPG_MOD 727>,
 		 <&x12_clk>,
 		 <&extal_clk>;
 	clock-names = "fck", "dclkin.0", "extal";

 	ports {
 		port@1 {
 			lvds0_out: endpoint {
 				remote-endpoint = <&thc63lvd1024_in>;
 			};
 		};
 	};
 };

 &lvds1 {
 	/*
 	 * Even though the LVDS1 output is not connected, the encoder must be
 	 * enabled to supply a pixel clock to the DU for the DPAD output when
 	 * LVDS0 is in use.
 	 */
 	status = "okay";

 	clocks = <&cpg CPG_MOD 727>,
 		 <&x12_clk>,
 		 <&extal_clk>;
 	clock-names = "fck", "dclkin.0", "extal";
 };

 &ohci0 {
 	dr_mode = "host";
 	status = "okay";
 };

 &pfc {
 	avb0_pins: avb {
 		groups = "avb0_link", "avb0_mdio", "avb0_mii";
 		function = "avb0";
 	};

 	can0_pins: can0 {
 		groups = "can0_data_a";
 		function = "can0";
 	};

 	can1_pins: can1 {
 		groups = "can1_data_a";
 		function = "can1";
 	};

 	du_pins: du {
 		groups = "du_rgb888", "du_sync", "du_disp", "du_clk_out_0";
 		function = "du";
 	};

 	i2c0_pins: i2c0 {
 		groups = "i2c0";
 		function = "i2c0";
 	};

 	i2c1_pins: i2c1 {
 		groups = "i2c1";
 		function = "i2c1";
 	};

 	keys_pins: keys {
 		pins = "GP_4_12", "GP_4_13", "GP_4_14", "GP_4_15";
 		bias-pull-up;
 	};

 	pwm0_pins: pwm0 {
 		groups = "pwm0_c";
 		function = "pwm0";
 	};

 	pwm1_pins: pwm1 {
 		groups = "pwm1_c";
 		function = "pwm1";
 	};

 	scif2_pins: scif2 {
 		groups = "scif2_data";
 		function = "scif2";
 	};

 	sdhi2_pins: sd2 {
 		groups = "mmc_data8", "mmc_ctrl";
 		function = "mmc";
 		power-source = <1800>;
 	};

 	sdhi2_pins_uhs: sd2_uhs {
 		groups = "mmc_data8", "mmc_ctrl";
 		function = "mmc";
 		power-source = <1800>;
 	};

 	sound_pins: sound {
 		groups = "ssi34_ctrl", "ssi3_data", "ssi4_data_a";
 		function = "ssi";
 	};

 	sound_clk_pins: sound-clk {
 		groups = "audio_clk_a", "audio_clk_b",
 			 "audio_clkout", "audio_clkout1";
 		function = "audio_clk";
 	};

 	usb0_pins: usb0 {
 		groups = "usb0";
 		function = "usb0";
 	};

 	vin4_pins_cvbs: vin4 {
 		groups = "vin4_data8", "vin4_sync", "vin4_clk";
 		function = "vin4";
 	};
 };

 &pwm0 {
 	pinctrl-0 = <&pwm0_pins>;
 	pinctrl-names = "default";

 	status = "okay";
 };

 &pwm1 {
 	pinctrl-0 = <&pwm1_pins>;
 	pinctrl-names = "default";

 	status = "okay";
 };

 &rcar_sound {
 	pinctrl-0 = <&sound_pins>, <&sound_clk_pins>;
 	pinctrl-names = "default";

 	/* Single DAI */
 	#sound-dai-cells = <0>;

 	/* audio_clkout0/1 */
 	#clock-cells = <1>;
 	clock-frequency = <12288000 11289600>;

 	status = "okay";

 	clocks = <&cpg CPG_MOD 1005>,
 		 <&cpg CPG_MOD 1011>, <&cpg CPG_MOD 1012>,
 		 <&cpg CPG_MOD 1025>, <&cpg CPG_MOD 1026>,
 		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
 		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
 		 <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
 		 <&cs2000>, <&audio_clk_b>,
 		 <&cpg CPG_CORE R8A77995_CLK_ZA2>;

 	ports {
 		rsnd_port0: port {
 			rsnd_for_ak4613: endpoint {
 				remote-endpoint = <&ak4613_endpoint>;
 				dai-format = "left_j";
 				bitclock-master = <&rsnd_for_ak4613>;
 				frame-master = <&rsnd_for_ak4613>;
 				playback = <&ssi3>, <&src5>, <&dvc0>;
 				capture  = <&ssi4>, <&src6>, <&dvc1>;
 			};
 		};
 	};
 };

 &rwdt {
 	timeout-sec = <60>;
 	status = "okay";
 };

 &scif2 {
 	pinctrl-0 = <&scif2_pins>;
 	pinctrl-names = "default";

 	status = "okay";
 };

 &sdhi2 {
 	/* used for on-board eMMC */
 	pinctrl-0 = <&sdhi2_pins>;
 	pinctrl-1 = <&sdhi2_pins_uhs>;
 	pinctrl-names = "default", "state_uhs";

 	vmmc-supply = <&reg_3p3v>;
 	vqmmc-supply = <&reg_1p8v>;
 	bus-width = <8>;
 	mmc-hs200-1_8v;
 	no-sd;
 	no-sdio;
 	non-removable;
 	status = "okay";
 };

 &ssi4 {
 	shared-pin;
 };

 &usb2_phy0 {
 	pinctrl-0 = <&usb0_pins>;
 	pinctrl-names = "default";

 	renesas,no-otg-pins;
 	status = "okay";
 };

 &vin4 {
 	pinctrl-0 = <&vin4_pins_cvbs>;
 	pinctrl-names = "default";

 	status = "okay";

 	ports {
 		port {
 			vin4_in: endpoint {
 				remote-endpoint = <&adv7180_out>;
 			};
 		};
 	};
 };
	// SPDX-License-Identifier: GPL-2.0
	/*
	* Device Tree Source for the Draak board
	*
	* Copyright (C) 2016-2018 Renesas Electronics Corp.
	* Copyright (C) 2017 Glider bvba
	*/

	#include <dt-bindings/gpio/gpio.h>
	#include <dt-bindings/input/input.h>

	/ {
	model = "Renesas Draak board";
	compatible = "renesas,draak";

	aliases {
	serial0 = &scif2;
	ethernet0 = &avb;
	};

	audio_clkout: audio-clkout {
	/*
	* This is same as <&rcar_sound 0>
	* but needed to avoid cs2000/rcar_sound probe dead-lock
	*/
	compatible = "fixed-clock";
	#clock-cells = <0>;
	clock-frequency = <12288000>;
	};

	backlight: backlight {
	compatible = "pwm-backlight";
	pwms = <&pwm1 0 50000>;

	brightness-levels = <512 511 505 494 473 440 392 327 241 133 0>;
	default-brightness-level = <10>;

	power-supply = <&reg_12p0v>;
	enable-gpios = <&gpio4 0 GPIO_ACTIVE_HIGH>;
	};

	chosen {
	bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
	stdout-path = "serial0:115200n8";
	};

	composite-in {
	compatible = "composite-video-connector";

	port {
	composite_con_in: endpoint {
	remote-endpoint = <&adv7180_in>;
	};
	};
	};

	hdmi-in {
	compatible = "hdmi-connector";
	type = "a";

	port {
	hdmi_con_in: endpoint {
	remote-endpoint = <&adv7612_in>;
	};
	};
	};

	hdmi-out {
	compatible = "hdmi-connector";
	type = "a";

	port {
	hdmi_con_out: endpoint {
	remote-endpoint = <&adv7511_out>;
	};
	};
	};

	keys {
	compatible = "gpio-keys";

	pinctrl-0 = <&keys_pins>;
	pinctrl-names = "default";

	key-1 {
	gpios = <&gpio4 12 GPIO_ACTIVE_LOW>;
	linux,code = <KEY_1>;
	label = "SW56-1";
	wakeup-source;
	debounce-interval = <20>;
	};
	key-2 {
	gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
	linux,code = <KEY_2>;
	label = "SW56-2";
	wakeup-source;
	debounce-interval = <20>;
	};
	key-3 {
	gpios = <&gpio4 14 GPIO_ACTIVE_LOW>;
	linux,code = <KEY_3>;
	label = "SW56-3";
	wakeup-source;
	debounce-interval = <20>;
	};
	key-4 {
	gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
	linux,code = <KEY_4>;
	label = "SW56-4";
	wakeup-source;
	debounce-interval = <20>;
	};
	};

	lvds-decoder {
	compatible = "thine,thc63lvd1024";
	vcc-supply = <&reg_3p3v>;

	ports {
	#address-cells = <1>;
	#size-cells = <0>;

	port@0 {
	reg = <0>;
	thc63lvd1024_in: endpoint {
	remote-endpoint = <&lvds0_out>;
	};
	};

	port@2 {
	reg = <2>;
	thc63lvd1024_out: endpoint {
	remote-endpoint = <&adv7511_in>;
	};
	};
	};
	};

	memory@48000000 {
	device_type = "memory";
	/* first 128MB is reserved for secure area. */
	reg = <0x0 0x48000000 0x0 0x18000000>;
	};

	reg_1p8v: regulator-1p8v {
	compatible = "regulator-fixed";
	regulator-name = "fixed-1.8V";
	regulator-min-microvolt = <1800000>;
	regulator-max-microvolt = <1800000>;
	regulator-boot-on;
	regulator-always-on;
	};

	reg_3p3v: regulator-3p3v {
	compatible = "regulator-fixed";
	regulator-name = "fixed-3.3V";
	regulator-min-microvolt = <3300000>;
	regulator-max-microvolt = <3300000>;
	regulator-boot-on;
	regulator-always-on;
	};

	reg_12p0v: regulator-12p0v {
	compatible = "regulator-fixed";
	regulator-name = "D12.0V";
	regulator-min-microvolt = <12000000>;
	regulator-max-microvolt = <12000000>;
	regulator-boot-on;
	regulator-always-on;
	};

	sound_card: sound {
	compatible = "audio-graph-card";

	dais = <&rsnd_port0 /* ak4613 */
	/* HDMI is not yet supported */
	>;
	};

	vga {
	compatible = "vga-connector";

	port {
	vga_in: endpoint {
	remote-endpoint = <&adv7123_out>;
	};
	};
	};

	vga-encoder {
	compatible = "adi,adv7123";

	ports {
	#address-cells = <1>;
	#size-cells = <0>;

	port@0 {
	reg = <0>;
	adv7123_in: endpoint {
	remote-endpoint = <&du_out_rgb>;
	};
	};
	port@1 {
	reg = <1>;
	adv7123_out: endpoint {
	remote-endpoint = <&vga_in>;
	};
	};
	};
	};

	x12_clk: x12 {
	compatible = "fixed-clock";
	#clock-cells = <0>;
	clock-frequency = <74250000>;
	};

	x19_clk: x19 {
	compatible = "fixed-clock";
	#clock-cells = <0>;
	clock-frequency = <24576000>;
	};
	};

	&audio_clk_b {
	/*
	* X11 is connected to VI4_FIELD/SCIF_CLK/AUDIO_CLKB,
	* and R-Car Sound uses AUDIO_CLKB.
	* Note is that schematic indicates VI4_FIELD conection only
	* not AUDIO_CLKB at SoC page.
	* And this VI4_FIELD/SCIF_CLK/AUDIO_CLKB is connected to SW60.
	* SW60 should be 1-2.
	*/

	clock-frequency = <22579200>;
	};

	&avb {
	pinctrl-0 = <&avb0_pins>;
	pinctrl-names = "default";
	renesas,no-ether-link;
	phy-handle = <&phy0>;
	status = "okay";

	phy0: ethernet-phy@0 {
	compatible = "ethernet-phy-id0022.1622",
	"ethernet-phy-ieee802.3-c22";
	rxc-skew-ps = <1500>;
	reg = <0>;
	interrupt-parent = <&gpio5>;
	interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
	reset-gpios = <&gpio5 18 GPIO_ACTIVE_LOW>;
	/*
	* TX clock internal delay mode is required for reliable
	* 1Gbps communication using the KSZ9031RNX phy present on
	* the Draak board, however, TX clock internal delay mode
	* isn't supported on R-Car D3(e). Thus, limit speed to
	* 100Mbps for reliable communication.
	*/
	max-speed = <100>;
	};
	};

	&can0 {
	pinctrl-0 = <&can0_pins>;
	pinctrl-names = "default";
	status = "okay";
	};

	&can1 {
	pinctrl-0 = <&can1_pins>;
	pinctrl-names = "default";
	status = "okay";
	};

	&du {
	pinctrl-0 = <&du_pins>;
	pinctrl-names = "default";
	status = "okay";

	clocks = <&cpg CPG_MOD 724>,
	<&cpg CPG_MOD 723>,
	<&x12_clk>;
	clock-names = "du.0", "du.1", "dclkin.0";

	ports {
	port@0 {
	endpoint {
	remote-endpoint = <&adv7123_in>;
	};
	};
	};
	};

	&ehci0 {
	dr_mode = "host";
	status = "okay";
	};

	&extal_clk {
	clock-frequency = <48000000>;
	};

	&hsusb {
	dr_mode = "host";
	status = "okay";
	};

	&i2c0 {
	pinctrl-0 = <&i2c0_pins>;
	pinctrl-names = "default";
	status = "okay";

	ak4613: codec@10 {
	compatible = "asahi-kasei,ak4613";
	#sound-dai-cells = <0>;
	reg = <0x10>;
	clocks = <&rcar_sound 0>; /* audio_clkout */

	asahi-kasei,in1-single-end;
	asahi-kasei,in2-single-end;
	asahi-kasei,out1-single-end;
	asahi-kasei,out2-single-end;
	asahi-kasei,out3-single-end;
	asahi-kasei,out4-single-end;
	asahi-kasei,out5-single-end;
	asahi-kasei,out6-single-end;

	port {
	ak4613_endpoint: endpoint {
	remote-endpoint = <&rsnd_for_ak4613>;
	};
	};
	};

	composite-in@20 {
	compatible = "adi,adv7180cp";
	reg = <0x20>;

	ports {
	#address-cells = <1>;
	#size-cells = <0>;

	port@0 {
	reg = <0>;
	adv7180_in: endpoint {
	remote-endpoint = <&composite_con_in>;
	};
	};

	port@3 {
	reg = <3>;

	/*
	* The VIN4 video input path is shared between
	* CVBS and HDMI inputs through SW[49-53]
	* switches.
	*
	* CVBS is the default selection, link it to
	* VIN4 here.
	*/
	adv7180_out: endpoint {
	remote-endpoint = <&vin4_in>;
	};
	};
	};

	};

	hdmi-encoder@39 {
	compatible = "adi,adv7511w";
	reg = <0x39>, <0x3f>, <0x3c>, <0x38>;
	reg-names = "main", "edid", "cec", "packet";
	interrupt-parent = <&gpio1>;
	interrupts = <28 IRQ_TYPE_LEVEL_LOW>;

	adi,input-depth = <8>;
	adi,input-colorspace = "rgb";
	adi,input-clock = "1x";

	ports {
	#address-cells = <1>;
	#size-cells = <0>;

	port@0 {
	reg = <0>;
	adv7511_in: endpoint {
	remote-endpoint = <&thc63lvd1024_out>;
	};
	};

	port@1 {
	reg = <1>;
	adv7511_out: endpoint {
	remote-endpoint = <&hdmi_con_out>;
	};
	};
	};
	};

	hdmi-decoder@4c {
	compatible = "adi,adv7612";
	reg = <0x4c>;
	default-input = <0>;

	ports {
	#address-cells = <1>;
	#size-cells = <0>;

	port@0 {
	reg = <0>;

	adv7612_in: endpoint {
	remote-endpoint = <&hdmi_con_in>;
	};
	};

	port@2 {
	reg = <2>;

	/*
	* The VIN4 video input path is shared between
	* CVBS and HDMI inputs through SW[49-53]
	* switches.
	*
	* CVBS is the default selection, leave HDMI
	* not connected here.
	*/
	adv7612_out: endpoint {
	pclk-sample = <0>;
	hsync-active = <0>;
	vsync-active = <0>;
	};
	};
	};
	};

	cs2000: clk-multiplier@4f {
	#clock-cells = <0>;
	compatible = "cirrus,cs2000-cp";
	reg = <0x4f>;
	clocks = <&audio_clkout>, <&x19_clk>; /* audio_clkout_1, x19 */
	clock-names = "clk_in", "ref_clk";

	assigned-clocks = <&cs2000>;
	assigned-clock-rates = <24576000>; /* 1/1 divide */
	};

	eeprom@50 {
	compatible = "rohm,br24t01", "atmel,24c01";
	reg = <0x50>;
	pagesize = <8>;
	};
	};

	&i2c1 {
	pinctrl-0 = <&i2c1_pins>;
	pinctrl-names = "default";
	status = "okay";
	};

	&lvds0 {
	status = "okay";

	clocks = <&cpg CPG_MOD 727>,
	<&x12_clk>,
	<&extal_clk>;
	clock-names = "fck", "dclkin.0", "extal";

	ports {
	port@1 {
	lvds0_out: endpoint {
	remote-endpoint = <&thc63lvd1024_in>;
	};
	};
	};
	};

	&lvds1 {
	/*
	* Even though the LVDS1 output is not connected, the encoder must be
	* enabled to supply a pixel clock to the DU for the DPAD output when
	* LVDS0 is in use.
	*/
	status = "okay";

	clocks = <&cpg CPG_MOD 727>,
	<&x12_clk>,
	<&extal_clk>;
	clock-names = "fck", "dclkin.0", "extal";
	};

	&ohci0 {
	dr_mode = "host";
	status = "okay";
	};

	&pfc {
	avb0_pins: avb {
	groups = "avb0_link", "avb0_mdio", "avb0_mii";
	function = "avb0";
	};

	can0_pins: can0 {
	groups = "can0_data_a";
	function = "can0";
	};

	can1_pins: can1 {
	groups = "can1_data_a";
	function = "can1";
	};

	du_pins: du {
	groups = "du_rgb888", "du_sync", "du_disp", "du_clk_out_0";
	function = "du";
	};

	i2c0_pins: i2c0 {
	groups = "i2c0";
	function = "i2c0";
	};

	i2c1_pins: i2c1 {
	groups = "i2c1";
	function = "i2c1";
	};

	keys_pins: keys {
	pins = "GP_4_12", "GP_4_13", "GP_4_14", "GP_4_15";
	bias-pull-up;
	};

	pwm0_pins: pwm0 {
	groups = "pwm0_c";
	function = "pwm0";
	};

	pwm1_pins: pwm1 {
	groups = "pwm1_c";
	function = "pwm1";
	};

	scif2_pins: scif2 {
	groups = "scif2_data";
	function = "scif2";
	};

	sdhi2_pins: sd2 {
	groups = "mmc_data8", "mmc_ctrl";
	function = "mmc";
	power-source = <1800>;
	};

	sdhi2_pins_uhs: sd2_uhs {
	groups = "mmc_data8", "mmc_ctrl";
	function = "mmc";
	power-source = <1800>;
	};

	sound_pins: sound {
	groups = "ssi34_ctrl", "ssi3_data", "ssi4_data_a";
	function = "ssi";
	};

	sound_clk_pins: sound-clk {
	groups = "audio_clk_a", "audio_clk_b",
	"audio_clkout", "audio_clkout1";
	function = "audio_clk";
	};

	usb0_pins: usb0 {
	groups = "usb0";
	function = "usb0";
	};

	vin4_pins_cvbs: vin4 {
	groups = "vin4_data8", "vin4_sync", "vin4_clk";
	function = "vin4";
	};
	};

	&pwm0 {
	pinctrl-0 = <&pwm0_pins>;
	pinctrl-names = "default";

	status = "okay";
	};

	&pwm1 {
	pinctrl-0 = <&pwm1_pins>;
	pinctrl-names = "default";

	status = "okay";
	};

	&rcar_sound {
	pinctrl-0 = <&sound_pins>, <&sound_clk_pins>;
	pinctrl-names = "default";

	/* Single DAI */
	#sound-dai-cells = <0>;

	/* audio_clkout0/1 */
	#clock-cells = <1>;
	clock-frequency = <12288000 11289600>;

	status = "okay";

	clocks = <&cpg CPG_MOD 1005>,
	<&cpg CPG_MOD 1011>, <&cpg CPG_MOD 1012>,
	<&cpg CPG_MOD 1025>, <&cpg CPG_MOD 1026>,
	<&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
	<&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
	<&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
	<&cs2000>, <&audio_clk_b>,
	<&cpg CPG_CORE R8A77995_CLK_ZA2>;

	ports {
	rsnd_port0: port {
	rsnd_for_ak4613: endpoint {
	remote-endpoint = <&ak4613_endpoint>;
	dai-format = "left_j";
	bitclock-master = <&rsnd_for_ak4613>;
	frame-master = <&rsnd_for_ak4613>;
	playback = <&ssi3>, <&src5>, <&dvc0>;
	capture = <&ssi4>, <&src6>, <&dvc1>;
	};
	};
	};
	};

	&rwdt {
	timeout-sec = <60>;
	status = "okay";
	};

	&scif2 {
	pinctrl-0 = <&scif2_pins>;
	pinctrl-names = "default";

	status = "okay";
	};

	&sdhi2 {
	/* used for on-board eMMC */
	pinctrl-0 = <&sdhi2_pins>;
	pinctrl-1 = <&sdhi2_pins_uhs>;
	pinctrl-names = "default", "state_uhs";

	vmmc-supply = <&reg_3p3v>;
	vqmmc-supply = <&reg_1p8v>;
	bus-width = <8>;
	mmc-hs200-1_8v;
	no-sd;
	no-sdio;
	non-removable;
	status = "okay";
	};

	&ssi4 {
	shared-pin;
	};

	&usb2_phy0 {
	pinctrl-0 = <&usb0_pins>;
	pinctrl-names = "default";

	renesas,no-otg-pins;
	status = "okay";
	};

	&vin4 {
	pinctrl-0 = <&vin4_pins_cvbs>;
	pinctrl-names = "default";

	status = "okay";

	ports {
	port {
	vin4_in: endpoint {
	remote-endpoint = <&adv7180_out>;
	};
	};
	};
	};