| // SPDX-License-Identifier: GPL-2.0-or-later |
| /* |
| * Copyright 2014 IBM Corp. |
| */ |
| |
| #include <linux/pci_regs.h> |
| #include <linux/pci_ids.h> |
| #include <linux/device.h> |
| #include <linux/module.h> |
| #include <linux/kernel.h> |
| #include <linux/slab.h> |
| #include <linux/sort.h> |
| #include <linux/pci.h> |
| #include <linux/of.h> |
| #include <linux/delay.h> |
| #include <asm/opal.h> |
| #include <asm/msi_bitmap.h> |
| #include <asm/pnv-pci.h> |
| #include <asm/io.h> |
| #include <asm/reg.h> |
| |
| #include "cxl.h" |
| #include <misc/cxl.h> |
| |
| |
| #define CXL_PCI_VSEC_ID 0x1280 |
| #define CXL_VSEC_MIN_SIZE 0x80 |
| |
| #define CXL_READ_VSEC_LENGTH(dev, vsec, dest) \ |
| { \ |
| pci_read_config_word(dev, vsec + 0x6, dest); \ |
| *dest >>= 4; \ |
| } |
| #define CXL_READ_VSEC_NAFUS(dev, vsec, dest) \ |
| pci_read_config_byte(dev, vsec + 0x8, dest) |
| |
| #define CXL_READ_VSEC_STATUS(dev, vsec, dest) \ |
| pci_read_config_byte(dev, vsec + 0x9, dest) |
| #define CXL_STATUS_SECOND_PORT 0x80 |
| #define CXL_STATUS_MSI_X_FULL 0x40 |
| #define CXL_STATUS_MSI_X_SINGLE 0x20 |
| #define CXL_STATUS_FLASH_RW 0x08 |
| #define CXL_STATUS_FLASH_RO 0x04 |
| #define CXL_STATUS_LOADABLE_AFU 0x02 |
| #define CXL_STATUS_LOADABLE_PSL 0x01 |
| /* If we see these features we won't try to use the card */ |
| #define CXL_UNSUPPORTED_FEATURES \ |
| (CXL_STATUS_MSI_X_FULL | CXL_STATUS_MSI_X_SINGLE) |
| |
| #define CXL_READ_VSEC_MODE_CONTROL(dev, vsec, dest) \ |
| pci_read_config_byte(dev, vsec + 0xa, dest) |
| #define CXL_WRITE_VSEC_MODE_CONTROL(dev, vsec, val) \ |
| pci_write_config_byte(dev, vsec + 0xa, val) |
| #define CXL_VSEC_PROTOCOL_MASK 0xe0 |
| #define CXL_VSEC_PROTOCOL_1024TB 0x80 |
| #define CXL_VSEC_PROTOCOL_512TB 0x40 |
| #define CXL_VSEC_PROTOCOL_256TB 0x20 /* Power 8/9 uses this */ |
| #define CXL_VSEC_PROTOCOL_ENABLE 0x01 |
| |
| #define CXL_READ_VSEC_PSL_REVISION(dev, vsec, dest) \ |
| pci_read_config_word(dev, vsec + 0xc, dest) |
| #define CXL_READ_VSEC_CAIA_MINOR(dev, vsec, dest) \ |
| pci_read_config_byte(dev, vsec + 0xe, dest) |
| #define CXL_READ_VSEC_CAIA_MAJOR(dev, vsec, dest) \ |
| pci_read_config_byte(dev, vsec + 0xf, dest) |
| #define CXL_READ_VSEC_BASE_IMAGE(dev, vsec, dest) \ |
| pci_read_config_word(dev, vsec + 0x10, dest) |
| |
| #define CXL_READ_VSEC_IMAGE_STATE(dev, vsec, dest) \ |
| pci_read_config_byte(dev, vsec + 0x13, dest) |
| #define CXL_WRITE_VSEC_IMAGE_STATE(dev, vsec, val) \ |
| pci_write_config_byte(dev, vsec + 0x13, val) |
| #define CXL_VSEC_USER_IMAGE_LOADED 0x80 /* RO */ |
| #define CXL_VSEC_PERST_LOADS_IMAGE 0x20 /* RW */ |
| #define CXL_VSEC_PERST_SELECT_USER 0x10 /* RW */ |
| |
| #define CXL_READ_VSEC_AFU_DESC_OFF(dev, vsec, dest) \ |
| pci_read_config_dword(dev, vsec + 0x20, dest) |
| #define CXL_READ_VSEC_AFU_DESC_SIZE(dev, vsec, dest) \ |
| pci_read_config_dword(dev, vsec + 0x24, dest) |
| #define CXL_READ_VSEC_PS_OFF(dev, vsec, dest) \ |
| pci_read_config_dword(dev, vsec + 0x28, dest) |
| #define CXL_READ_VSEC_PS_SIZE(dev, vsec, dest) \ |
| pci_read_config_dword(dev, vsec + 0x2c, dest) |
| |
| |
| /* This works a little different than the p1/p2 register accesses to make it |
| * easier to pull out individual fields */ |
| #define AFUD_READ(afu, off) in_be64(afu->native->afu_desc_mmio + off) |
| #define AFUD_READ_LE(afu, off) in_le64(afu->native->afu_desc_mmio + off) |
| #define EXTRACT_PPC_BIT(val, bit) (!!(val & PPC_BIT(bit))) |
| #define EXTRACT_PPC_BITS(val, bs, be) ((val & PPC_BITMASK(bs, be)) >> PPC_BITLSHIFT(be)) |
| |
| #define AFUD_READ_INFO(afu) AFUD_READ(afu, 0x0) |
| #define AFUD_NUM_INTS_PER_PROC(val) EXTRACT_PPC_BITS(val, 0, 15) |
| #define AFUD_NUM_PROCS(val) EXTRACT_PPC_BITS(val, 16, 31) |
| #define AFUD_NUM_CRS(val) EXTRACT_PPC_BITS(val, 32, 47) |
| #define AFUD_MULTIMODE(val) EXTRACT_PPC_BIT(val, 48) |
| #define AFUD_PUSH_BLOCK_TRANSFER(val) EXTRACT_PPC_BIT(val, 55) |
| #define AFUD_DEDICATED_PROCESS(val) EXTRACT_PPC_BIT(val, 59) |
| #define AFUD_AFU_DIRECTED(val) EXTRACT_PPC_BIT(val, 61) |
| #define AFUD_TIME_SLICED(val) EXTRACT_PPC_BIT(val, 63) |
| #define AFUD_READ_CR(afu) AFUD_READ(afu, 0x20) |
| #define AFUD_CR_LEN(val) EXTRACT_PPC_BITS(val, 8, 63) |
| #define AFUD_READ_CR_OFF(afu) AFUD_READ(afu, 0x28) |
| #define AFUD_READ_PPPSA(afu) AFUD_READ(afu, 0x30) |
| #define AFUD_PPPSA_PP(val) EXTRACT_PPC_BIT(val, 6) |
| #define AFUD_PPPSA_PSA(val) EXTRACT_PPC_BIT(val, 7) |
| #define AFUD_PPPSA_LEN(val) EXTRACT_PPC_BITS(val, 8, 63) |
| #define AFUD_READ_PPPSA_OFF(afu) AFUD_READ(afu, 0x38) |
| #define AFUD_READ_EB(afu) AFUD_READ(afu, 0x40) |
| #define AFUD_EB_LEN(val) EXTRACT_PPC_BITS(val, 8, 63) |
| #define AFUD_READ_EB_OFF(afu) AFUD_READ(afu, 0x48) |
| |
| static const struct pci_device_id cxl_pci_tbl[] = { |
| { PCI_DEVICE(PCI_VENDOR_ID_IBM, 0x0477), }, |
| { PCI_DEVICE(PCI_VENDOR_ID_IBM, 0x044b), }, |
| { PCI_DEVICE(PCI_VENDOR_ID_IBM, 0x04cf), }, |
| { PCI_DEVICE(PCI_VENDOR_ID_IBM, 0x0601), }, |
| { PCI_DEVICE(PCI_VENDOR_ID_IBM, 0x0623), }, |
| { PCI_DEVICE(PCI_VENDOR_ID_IBM, 0x0628), }, |
| { } |
| }; |
| MODULE_DEVICE_TABLE(pci, cxl_pci_tbl); |
| |
| |
| /* |
| * Mostly using these wrappers to avoid confusion: |
| * priv 1 is BAR2, while priv 2 is BAR0 |
| */ |
| static inline resource_size_t p1_base(struct pci_dev *dev) |
| { |
| return pci_resource_start(dev, 2); |
| } |
| |
| static inline resource_size_t p1_size(struct pci_dev *dev) |
| { |
| return pci_resource_len(dev, 2); |
| } |
| |
| static inline resource_size_t p2_base(struct pci_dev *dev) |
| { |
| return pci_resource_start(dev, 0); |
| } |
| |
| static inline resource_size_t p2_size(struct pci_dev *dev) |
| { |
| return pci_resource_len(dev, 0); |
| } |
| |
| static int find_cxl_vsec(struct pci_dev *dev) |
| { |
| return pci_find_vsec_capability(dev, PCI_VENDOR_ID_IBM, CXL_PCI_VSEC_ID); |
| } |
| |
| static void dump_cxl_config_space(struct pci_dev *dev) |
| { |
| int vsec; |
| u32 val; |
| |
| dev_info(&dev->dev, "dump_cxl_config_space\n"); |
| |
| pci_read_config_dword(dev, PCI_BASE_ADDRESS_0, &val); |
| dev_info(&dev->dev, "BAR0: %#.8x\n", val); |
| pci_read_config_dword(dev, PCI_BASE_ADDRESS_1, &val); |
| dev_info(&dev->dev, "BAR1: %#.8x\n", val); |
| pci_read_config_dword(dev, PCI_BASE_ADDRESS_2, &val); |
| dev_info(&dev->dev, "BAR2: %#.8x\n", val); |
| pci_read_config_dword(dev, PCI_BASE_ADDRESS_3, &val); |
| dev_info(&dev->dev, "BAR3: %#.8x\n", val); |
| pci_read_config_dword(dev, PCI_BASE_ADDRESS_4, &val); |
| dev_info(&dev->dev, "BAR4: %#.8x\n", val); |
| pci_read_config_dword(dev, PCI_BASE_ADDRESS_5, &val); |
| dev_info(&dev->dev, "BAR5: %#.8x\n", val); |
| |
| dev_info(&dev->dev, "p1 regs: %#llx, len: %#llx\n", |
| p1_base(dev), p1_size(dev)); |
| dev_info(&dev->dev, "p2 regs: %#llx, len: %#llx\n", |
| p2_base(dev), p2_size(dev)); |
| dev_info(&dev->dev, "BAR 4/5: %#llx, len: %#llx\n", |
| pci_resource_start(dev, 4), pci_resource_len(dev, 4)); |
| |
| if (!(vsec = find_cxl_vsec(dev))) |
| return; |
| |
| #define show_reg(name, what) \ |
| dev_info(&dev->dev, "cxl vsec: %30s: %#x\n", name, what) |
| |
| pci_read_config_dword(dev, vsec + 0x0, &val); |
| show_reg("Cap ID", (val >> 0) & 0xffff); |
| show_reg("Cap Ver", (val >> 16) & 0xf); |
| show_reg("Next Cap Ptr", (val >> 20) & 0xfff); |
| pci_read_config_dword(dev, vsec + 0x4, &val); |
| show_reg("VSEC ID", (val >> 0) & 0xffff); |
| show_reg("VSEC Rev", (val >> 16) & 0xf); |
| show_reg("VSEC Length", (val >> 20) & 0xfff); |
| pci_read_config_dword(dev, vsec + 0x8, &val); |
| show_reg("Num AFUs", (val >> 0) & 0xff); |
| show_reg("Status", (val >> 8) & 0xff); |
| show_reg("Mode Control", (val >> 16) & 0xff); |
| show_reg("Reserved", (val >> 24) & 0xff); |
| pci_read_config_dword(dev, vsec + 0xc, &val); |
| show_reg("PSL Rev", (val >> 0) & 0xffff); |
| show_reg("CAIA Ver", (val >> 16) & 0xffff); |
| pci_read_config_dword(dev, vsec + 0x10, &val); |
| show_reg("Base Image Rev", (val >> 0) & 0xffff); |
| show_reg("Reserved", (val >> 16) & 0x0fff); |
| show_reg("Image Control", (val >> 28) & 0x3); |
| show_reg("Reserved", (val >> 30) & 0x1); |
| show_reg("Image Loaded", (val >> 31) & 0x1); |
| |
| pci_read_config_dword(dev, vsec + 0x14, &val); |
| show_reg("Reserved", val); |
| pci_read_config_dword(dev, vsec + 0x18, &val); |
| show_reg("Reserved", val); |
| pci_read_config_dword(dev, vsec + 0x1c, &val); |
| show_reg("Reserved", val); |
| |
| pci_read_config_dword(dev, vsec + 0x20, &val); |
| show_reg("AFU Descriptor Offset", val); |
| pci_read_config_dword(dev, vsec + 0x24, &val); |
| show_reg("AFU Descriptor Size", val); |
| pci_read_config_dword(dev, vsec + 0x28, &val); |
| show_reg("Problem State Offset", val); |
| pci_read_config_dword(dev, vsec + 0x2c, &val); |
| show_reg("Problem State Size", val); |
| |
| pci_read_config_dword(dev, vsec + 0x30, &val); |
| show_reg("Reserved", val); |
| pci_read_config_dword(dev, vsec + 0x34, &val); |
| show_reg("Reserved", val); |
| pci_read_config_dword(dev, vsec + 0x38, &val); |
| show_reg("Reserved", val); |
| pci_read_config_dword(dev, vsec + 0x3c, &val); |
| show_reg("Reserved", val); |
| |
| pci_read_config_dword(dev, vsec + 0x40, &val); |
| show_reg("PSL Programming Port", val); |
| pci_read_config_dword(dev, vsec + 0x44, &val); |
| show_reg("PSL Programming Control", val); |
| |
| pci_read_config_dword(dev, vsec + 0x48, &val); |
| show_reg("Reserved", val); |
| pci_read_config_dword(dev, vsec + 0x4c, &val); |
| show_reg("Reserved", val); |
| |
| pci_read_config_dword(dev, vsec + 0x50, &val); |
| show_reg("Flash Address Register", val); |
| pci_read_config_dword(dev, vsec + 0x54, &val); |
| show_reg("Flash Size Register", val); |
| pci_read_config_dword(dev, vsec + 0x58, &val); |
| show_reg("Flash Status/Control Register", val); |
| pci_read_config_dword(dev, vsec + 0x58, &val); |
| show_reg("Flash Data Port", val); |
| |
| #undef show_reg |
| } |
| |
| static void dump_afu_descriptor(struct cxl_afu *afu) |
| { |
| u64 val, afu_cr_num, afu_cr_off, afu_cr_len; |
| int i; |
| |
| #define show_reg(name, what) \ |
| dev_info(&afu->dev, "afu desc: %30s: %#llx\n", name, what) |
| |
| val = AFUD_READ_INFO(afu); |
| show_reg("num_ints_per_process", AFUD_NUM_INTS_PER_PROC(val)); |
| show_reg("num_of_processes", AFUD_NUM_PROCS(val)); |
| show_reg("num_of_afu_CRs", AFUD_NUM_CRS(val)); |
| show_reg("req_prog_mode", val & 0xffffULL); |
| afu_cr_num = AFUD_NUM_CRS(val); |
| |
| val = AFUD_READ(afu, 0x8); |
| show_reg("Reserved", val); |
| val = AFUD_READ(afu, 0x10); |
| show_reg("Reserved", val); |
| val = AFUD_READ(afu, 0x18); |
| show_reg("Reserved", val); |
| |
| val = AFUD_READ_CR(afu); |
| show_reg("Reserved", (val >> (63-7)) & 0xff); |
| show_reg("AFU_CR_len", AFUD_CR_LEN(val)); |
| afu_cr_len = AFUD_CR_LEN(val) * 256; |
| |
| val = AFUD_READ_CR_OFF(afu); |
| afu_cr_off = val; |
| show_reg("AFU_CR_offset", val); |
| |
| val = AFUD_READ_PPPSA(afu); |
| show_reg("PerProcessPSA_control", (val >> (63-7)) & 0xff); |
| show_reg("PerProcessPSA Length", AFUD_PPPSA_LEN(val)); |
| |
| val = AFUD_READ_PPPSA_OFF(afu); |
| show_reg("PerProcessPSA_offset", val); |
| |
| val = AFUD_READ_EB(afu); |
| show_reg("Reserved", (val >> (63-7)) & 0xff); |
| show_reg("AFU_EB_len", AFUD_EB_LEN(val)); |
| |
| val = AFUD_READ_EB_OFF(afu); |
| show_reg("AFU_EB_offset", val); |
| |
| for (i = 0; i < afu_cr_num; i++) { |
| val = AFUD_READ_LE(afu, afu_cr_off + i * afu_cr_len); |
| show_reg("CR Vendor", val & 0xffff); |
| show_reg("CR Device", (val >> 16) & 0xffff); |
| } |
| #undef show_reg |
| } |
| |
| #define P8_CAPP_UNIT0_ID 0xBA |
| #define P8_CAPP_UNIT1_ID 0XBE |
| #define P9_CAPP_UNIT0_ID 0xC0 |
| #define P9_CAPP_UNIT1_ID 0xE0 |
| |
| static int get_phb_index(struct device_node *np, u32 *phb_index) |
| { |
| if (of_property_read_u32(np, "ibm,phb-index", phb_index)) |
| return -ENODEV; |
| return 0; |
| } |
| |
| static u64 get_capp_unit_id(struct device_node *np, u32 phb_index) |
| { |
| /* |
| * POWER 8: |
| * - For chips other than POWER8NVL, we only have CAPP 0, |
| * irrespective of which PHB is used. |
| * - For POWER8NVL, assume CAPP 0 is attached to PHB0 and |
| * CAPP 1 is attached to PHB1. |
| */ |
| if (cxl_is_power8()) { |
| if (!pvr_version_is(PVR_POWER8NVL)) |
| return P8_CAPP_UNIT0_ID; |
| |
| if (phb_index == 0) |
| return P8_CAPP_UNIT0_ID; |
| |
| if (phb_index == 1) |
| return P8_CAPP_UNIT1_ID; |
| } |
| |
| /* |
| * POWER 9: |
| * PEC0 (PHB0). Capp ID = CAPP0 (0b1100_0000) |
| * PEC1 (PHB1 - PHB2). No capi mode |
| * PEC2 (PHB3 - PHB4 - PHB5): Capi mode on PHB3 only. Capp ID = CAPP1 (0b1110_0000) |
| */ |
| if (cxl_is_power9()) { |
| if (phb_index == 0) |
| return P9_CAPP_UNIT0_ID; |
| |
| if (phb_index == 3) |
| return P9_CAPP_UNIT1_ID; |
| } |
| |
| return 0; |
| } |
| |
| int cxl_calc_capp_routing(struct pci_dev *dev, u64 *chipid, |
| u32 *phb_index, u64 *capp_unit_id) |
| { |
| int rc; |
| struct device_node *np; |
| u32 id; |
| |
| if (!(np = pnv_pci_get_phb_node(dev))) |
| return -ENODEV; |
| |
| while (np && of_property_read_u32(np, "ibm,chip-id", &id)) |
| np = of_get_next_parent(np); |
| if (!np) |
| return -ENODEV; |
| |
| *chipid = id; |
| |
| rc = get_phb_index(np, phb_index); |
| if (rc) { |
| pr_err("cxl: invalid phb index\n"); |
| of_node_put(np); |
| return rc; |
| } |
| |
| *capp_unit_id = get_capp_unit_id(np, *phb_index); |
| of_node_put(np); |
| if (!*capp_unit_id) { |
| pr_err("cxl: No capp unit found for PHB[%lld,%d]. Make sure the adapter is on a capi-compatible slot\n", |
| *chipid, *phb_index); |
| return -ENODEV; |
| } |
| |
| return 0; |
| } |
| |
| static DEFINE_MUTEX(indications_mutex); |
| |
| static int get_phb_indications(struct pci_dev *dev, u64 *capiind, u64 *asnind, |
| u64 *nbwind) |
| { |
| static u32 val[3]; |
| struct device_node *np; |
| |
| mutex_lock(&indications_mutex); |
| if (!val[0]) { |
| if (!(np = pnv_pci_get_phb_node(dev))) { |
| mutex_unlock(&indications_mutex); |
| return -ENODEV; |
| } |
| |
| if (of_property_read_u32_array(np, "ibm,phb-indications", val, 3)) { |
| val[2] = 0x0300UL; /* legacy values */ |
| val[1] = 0x0400UL; |
| val[0] = 0x0200UL; |
| } |
| of_node_put(np); |
| } |
| *capiind = val[0]; |
| *asnind = val[1]; |
| *nbwind = val[2]; |
| mutex_unlock(&indications_mutex); |
| return 0; |
| } |
| |
| int cxl_get_xsl9_dsnctl(struct pci_dev *dev, u64 capp_unit_id, u64 *reg) |
| { |
| u64 xsl_dsnctl; |
| u64 capiind, asnind, nbwind; |
| |
| /* |
| * CAPI Identifier bits [0:7] |
| * bit 61:60 MSI bits --> 0 |
| * bit 59 TVT selector --> 0 |
| */ |
| if (get_phb_indications(dev, &capiind, &asnind, &nbwind)) |
| return -ENODEV; |
| |
| /* |
| * Tell XSL where to route data to. |
| * The field chipid should match the PHB CAPI_CMPM register |
| */ |
| xsl_dsnctl = (capiind << (63-15)); /* Bit 57 */ |
| xsl_dsnctl |= (capp_unit_id << (63-15)); |
| |
| /* nMMU_ID Defaults to: b’000001001’*/ |
| xsl_dsnctl |= ((u64)0x09 << (63-28)); |
| |
| /* |
| * Used to identify CAPI packets which should be sorted into |
| * the Non-Blocking queues by the PHB. This field should match |
| * the PHB PBL_NBW_CMPM register |
| * nbwind=0x03, bits [57:58], must include capi indicator. |
| * Not supported on P9 DD1. |
| */ |
| xsl_dsnctl |= (nbwind << (63-55)); |
| |
| /* |
| * Upper 16b address bits of ASB_Notify messages sent to the |
| * system. Need to match the PHB’s ASN Compare/Mask Register. |
| * Not supported on P9 DD1. |
| */ |
| xsl_dsnctl |= asnind; |
| |
| *reg = xsl_dsnctl; |
| return 0; |
| } |
| |
| static int init_implementation_adapter_regs_psl9(struct cxl *adapter, |
| struct pci_dev *dev) |
| { |
| u64 xsl_dsnctl, psl_fircntl; |
| u64 chipid; |
| u32 phb_index; |
| u64 capp_unit_id; |
| u64 psl_debug; |
| int rc; |
| |
| rc = cxl_calc_capp_routing(dev, &chipid, &phb_index, &capp_unit_id); |
| if (rc) |
| return rc; |
| |
| rc = cxl_get_xsl9_dsnctl(dev, capp_unit_id, &xsl_dsnctl); |
| if (rc) |
| return rc; |
| |
| cxl_p1_write(adapter, CXL_XSL9_DSNCTL, xsl_dsnctl); |
| |
| /* Set fir_cntl to recommended value for production env */ |
| psl_fircntl = (0x2ULL << (63-3)); /* ce_report */ |
| psl_fircntl |= (0x1ULL << (63-6)); /* FIR_report */ |
| psl_fircntl |= 0x1ULL; /* ce_thresh */ |
| cxl_p1_write(adapter, CXL_PSL9_FIR_CNTL, psl_fircntl); |
| |
| /* Setup the PSL to transmit packets on the PCIe before the |
| * CAPP is enabled. Make sure that CAPP virtual machines are disabled |
| */ |
| cxl_p1_write(adapter, CXL_PSL9_DSNDCTL, 0x0001001000012A10ULL); |
| |
| /* |
| * A response to an ASB_Notify request is returned by the |
| * system as an MMIO write to the address defined in |
| * the PSL_TNR_ADDR register. |
| * keep the Reset Value: 0x00020000E0000000 |
| */ |
| |
| /* Enable XSL rty limit */ |
| cxl_p1_write(adapter, CXL_XSL9_DEF, 0x51F8000000000005ULL); |
| |
| /* Change XSL_INV dummy read threshold */ |
| cxl_p1_write(adapter, CXL_XSL9_INV, 0x0000040007FFC200ULL); |
| |
| if (phb_index == 3) { |
| /* disable machines 31-47 and 20-27 for DMA */ |
| cxl_p1_write(adapter, CXL_PSL9_APCDEDTYPE, 0x40000FF3FFFF0000ULL); |
| } |
| |
| /* Snoop machines */ |
| cxl_p1_write(adapter, CXL_PSL9_APCDEDALLOC, 0x800F000200000000ULL); |
| |
| /* Enable NORST and DD2 features */ |
| cxl_p1_write(adapter, CXL_PSL9_DEBUG, 0xC000000000000000ULL); |
| |
| /* |
| * Check if PSL has data-cache. We need to flush adapter datacache |
| * when as its about to be removed. |
| */ |
| psl_debug = cxl_p1_read(adapter, CXL_PSL9_DEBUG); |
| if (psl_debug & CXL_PSL_DEBUG_CDC) { |
| dev_dbg(&dev->dev, "No data-cache present\n"); |
| adapter->native->no_data_cache = true; |
| } |
| |
| return 0; |
| } |
| |
| static int init_implementation_adapter_regs_psl8(struct cxl *adapter, struct pci_dev *dev) |
| { |
| u64 psl_dsnctl, psl_fircntl; |
| u64 chipid; |
| u32 phb_index; |
| u64 capp_unit_id; |
| int rc; |
| |
| rc = cxl_calc_capp_routing(dev, &chipid, &phb_index, &capp_unit_id); |
| if (rc) |
| return rc; |
| |
| psl_dsnctl = 0x0000900000000000ULL; /* pteupd ttype, scdone */ |
| psl_dsnctl |= (0x2ULL << (63-38)); /* MMIO hang pulse: 256 us */ |
| /* Tell PSL where to route data to */ |
| psl_dsnctl |= (chipid << (63-5)); |
| psl_dsnctl |= (capp_unit_id << (63-13)); |
| |
| cxl_p1_write(adapter, CXL_PSL_DSNDCTL, psl_dsnctl); |
| cxl_p1_write(adapter, CXL_PSL_RESLCKTO, 0x20000000200ULL); |
| /* snoop write mask */ |
| cxl_p1_write(adapter, CXL_PSL_SNWRALLOC, 0x00000000FFFFFFFFULL); |
| /* set fir_cntl to recommended value for production env */ |
| psl_fircntl = (0x2ULL << (63-3)); /* ce_report */ |
| psl_fircntl |= (0x1ULL << (63-6)); /* FIR_report */ |
| psl_fircntl |= 0x1ULL; /* ce_thresh */ |
| cxl_p1_write(adapter, CXL_PSL_FIR_CNTL, psl_fircntl); |
| /* for debugging with trace arrays */ |
| cxl_p1_write(adapter, CXL_PSL_TRACE, 0x0000FF7C00000000ULL); |
| |
| return 0; |
| } |
| |
| /* PSL */ |
| #define TBSYNC_CAL(n) (((u64)n & 0x7) << (63-3)) |
| #define TBSYNC_CNT(n) (((u64)n & 0x7) << (63-6)) |
| /* For the PSL this is a multiple for 0 < n <= 7: */ |
| #define PSL_2048_250MHZ_CYCLES 1 |
| |
| static void write_timebase_ctrl_psl8(struct cxl *adapter) |
| { |
| cxl_p1_write(adapter, CXL_PSL_TB_CTLSTAT, |
| TBSYNC_CNT(2 * PSL_2048_250MHZ_CYCLES)); |
| } |
| |
| static u64 timebase_read_psl9(struct cxl *adapter) |
| { |
| return cxl_p1_read(adapter, CXL_PSL9_Timebase); |
| } |
| |
| static u64 timebase_read_psl8(struct cxl *adapter) |
| { |
| return cxl_p1_read(adapter, CXL_PSL_Timebase); |
| } |
| |
| static void cxl_setup_psl_timebase(struct cxl *adapter, struct pci_dev *dev) |
| { |
| struct device_node *np; |
| |
| adapter->psl_timebase_synced = false; |
| |
| if (!(np = pnv_pci_get_phb_node(dev))) |
| return; |
| |
| /* Do not fail when CAPP timebase sync is not supported by OPAL */ |
| of_node_get(np); |
| if (!of_property_present(np, "ibm,capp-timebase-sync")) { |
| of_node_put(np); |
| dev_info(&dev->dev, "PSL timebase inactive: OPAL support missing\n"); |
| return; |
| } |
| of_node_put(np); |
| |
| /* |
| * Setup PSL Timebase Control and Status register |
| * with the recommended Timebase Sync Count value |
| */ |
| if (adapter->native->sl_ops->write_timebase_ctrl) |
| adapter->native->sl_ops->write_timebase_ctrl(adapter); |
| |
| /* Enable PSL Timebase */ |
| cxl_p1_write(adapter, CXL_PSL_Control, 0x0000000000000000); |
| cxl_p1_write(adapter, CXL_PSL_Control, CXL_PSL_Control_tb); |
| |
| return; |
| } |
| |
| static int init_implementation_afu_regs_psl9(struct cxl_afu *afu) |
| { |
| return 0; |
| } |
| |
| static int init_implementation_afu_regs_psl8(struct cxl_afu *afu) |
| { |
| /* read/write masks for this slice */ |
| cxl_p1n_write(afu, CXL_PSL_APCALLOC_A, 0xFFFFFFFEFEFEFEFEULL); |
| /* APC read/write masks for this slice */ |
| cxl_p1n_write(afu, CXL_PSL_COALLOC_A, 0xFF000000FEFEFEFEULL); |
| /* for debugging with trace arrays */ |
| cxl_p1n_write(afu, CXL_PSL_SLICE_TRACE, 0x0000FFFF00000000ULL); |
| cxl_p1n_write(afu, CXL_PSL_RXCTL_A, CXL_PSL_RXCTL_AFUHP_4S); |
| |
| return 0; |
| } |
| |
| int cxl_pci_setup_irq(struct cxl *adapter, unsigned int hwirq, |
| unsigned int virq) |
| { |
| struct pci_dev *dev = to_pci_dev(adapter->dev.parent); |
| |
| return pnv_cxl_ioda_msi_setup(dev, hwirq, virq); |
| } |
| |
| int cxl_update_image_control(struct cxl *adapter) |
| { |
| struct pci_dev *dev = to_pci_dev(adapter->dev.parent); |
| int rc; |
| int vsec; |
| u8 image_state; |
| |
| if (!(vsec = find_cxl_vsec(dev))) { |
| dev_err(&dev->dev, "ABORTING: CXL VSEC not found!\n"); |
| return -ENODEV; |
| } |
| |
| if ((rc = CXL_READ_VSEC_IMAGE_STATE(dev, vsec, &image_state))) { |
| dev_err(&dev->dev, "failed to read image state: %i\n", rc); |
| return rc; |
| } |
| |
| if (adapter->perst_loads_image) |
| image_state |= CXL_VSEC_PERST_LOADS_IMAGE; |
| else |
| image_state &= ~CXL_VSEC_PERST_LOADS_IMAGE; |
| |
| if (adapter->perst_select_user) |
| image_state |= CXL_VSEC_PERST_SELECT_USER; |
| else |
| image_state &= ~CXL_VSEC_PERST_SELECT_USER; |
| |
| if ((rc = CXL_WRITE_VSEC_IMAGE_STATE(dev, vsec, image_state))) { |
| dev_err(&dev->dev, "failed to update image control: %i\n", rc); |
| return rc; |
| } |
| |
| return 0; |
| } |
| |
| int cxl_pci_alloc_one_irq(struct cxl *adapter) |
| { |
| struct pci_dev *dev = to_pci_dev(adapter->dev.parent); |
| |
| return pnv_cxl_alloc_hwirqs(dev, 1); |
| } |
| |
| void cxl_pci_release_one_irq(struct cxl *adapter, int hwirq) |
| { |
| struct pci_dev *dev = to_pci_dev(adapter->dev.parent); |
| |
| return pnv_cxl_release_hwirqs(dev, hwirq, 1); |
| } |
| |
| int cxl_pci_alloc_irq_ranges(struct cxl_irq_ranges *irqs, |
| struct cxl *adapter, unsigned int num) |
| { |
| struct pci_dev *dev = to_pci_dev(adapter->dev.parent); |
| |
| return pnv_cxl_alloc_hwirq_ranges(irqs, dev, num); |
| } |
| |
| void cxl_pci_release_irq_ranges(struct cxl_irq_ranges *irqs, |
| struct cxl *adapter) |
| { |
| struct pci_dev *dev = to_pci_dev(adapter->dev.parent); |
| |
| pnv_cxl_release_hwirq_ranges(irqs, dev); |
| } |
| |
| static int setup_cxl_bars(struct pci_dev *dev) |
| { |
| /* Safety check in case we get backported to < 3.17 without M64 */ |
| if ((p1_base(dev) < 0x100000000ULL) || |
| (p2_base(dev) < 0x100000000ULL)) { |
| dev_err(&dev->dev, "ABORTING: M32 BAR assignment incompatible with CXL\n"); |
| return -ENODEV; |
| } |
| |
| /* |
| * BAR 4/5 has a special meaning for CXL and must be programmed with a |
| * special value corresponding to the CXL protocol address range. |
| * For POWER 8/9 that means bits 48:49 must be set to 10 |
| */ |
| pci_write_config_dword(dev, PCI_BASE_ADDRESS_4, 0x00000000); |
| pci_write_config_dword(dev, PCI_BASE_ADDRESS_5, 0x00020000); |
| |
| return 0; |
| } |
| |
| /* pciex node: ibm,opal-m64-window = <0x3d058 0x0 0x3d058 0x0 0x8 0x0>; */ |
| static int switch_card_to_cxl(struct pci_dev *dev) |
| { |
| int vsec; |
| u8 val; |
| int rc; |
| |
| dev_info(&dev->dev, "switch card to CXL\n"); |
| |
| if (!(vsec = find_cxl_vsec(dev))) { |
| dev_err(&dev->dev, "ABORTING: CXL VSEC not found!\n"); |
| return -ENODEV; |
| } |
| |
| if ((rc = CXL_READ_VSEC_MODE_CONTROL(dev, vsec, &val))) { |
| dev_err(&dev->dev, "failed to read current mode control: %i", rc); |
| return rc; |
| } |
| val &= ~CXL_VSEC_PROTOCOL_MASK; |
| val |= CXL_VSEC_PROTOCOL_256TB | CXL_VSEC_PROTOCOL_ENABLE; |
| if ((rc = CXL_WRITE_VSEC_MODE_CONTROL(dev, vsec, val))) { |
| dev_err(&dev->dev, "failed to enable CXL protocol: %i", rc); |
| return rc; |
| } |
| /* |
| * The CAIA spec (v0.12 11.6 Bi-modal Device Support) states |
| * we must wait 100ms after this mode switch before touching |
| * PCIe config space. |
| */ |
| msleep(100); |
| |
| return 0; |
| } |
| |
| static int pci_map_slice_regs(struct cxl_afu *afu, struct cxl *adapter, struct pci_dev *dev) |
| { |
| u64 p1n_base, p2n_base, afu_desc; |
| const u64 p1n_size = 0x100; |
| const u64 p2n_size = 0x1000; |
| |
| p1n_base = p1_base(dev) + 0x10000 + (afu->slice * p1n_size); |
| p2n_base = p2_base(dev) + (afu->slice * p2n_size); |
| afu->psn_phys = p2_base(dev) + (adapter->native->ps_off + (afu->slice * adapter->ps_size)); |
| afu_desc = p2_base(dev) + adapter->native->afu_desc_off + (afu->slice * adapter->native->afu_desc_size); |
| |
| if (!(afu->native->p1n_mmio = ioremap(p1n_base, p1n_size))) |
| goto err; |
| if (!(afu->p2n_mmio = ioremap(p2n_base, p2n_size))) |
| goto err1; |
| if (afu_desc) { |
| if (!(afu->native->afu_desc_mmio = ioremap(afu_desc, adapter->native->afu_desc_size))) |
| goto err2; |
| } |
| |
| return 0; |
| err2: |
| iounmap(afu->p2n_mmio); |
| err1: |
| iounmap(afu->native->p1n_mmio); |
| err: |
| dev_err(&afu->dev, "Error mapping AFU MMIO regions\n"); |
| return -ENOMEM; |
| } |
| |
| static void pci_unmap_slice_regs(struct cxl_afu *afu) |
| { |
| if (afu->p2n_mmio) { |
| iounmap(afu->p2n_mmio); |
| afu->p2n_mmio = NULL; |
| } |
| if (afu->native->p1n_mmio) { |
| iounmap(afu->native->p1n_mmio); |
| afu->native->p1n_mmio = NULL; |
| } |
| if (afu->native->afu_desc_mmio) { |
| iounmap(afu->native->afu_desc_mmio); |
| afu->native->afu_desc_mmio = NULL; |
| } |
| } |
| |
| void cxl_pci_release_afu(struct device *dev) |
| { |
| struct cxl_afu *afu = to_cxl_afu(dev); |
| |
| pr_devel("%s\n", __func__); |
| |
| idr_destroy(&afu->contexts_idr); |
| cxl_release_spa(afu); |
| |
| kfree(afu->native); |
| kfree(afu); |
| } |
| |
| /* Expects AFU struct to have recently been zeroed out */ |
| static int cxl_read_afu_descriptor(struct cxl_afu *afu) |
| { |
| u64 val; |
| |
| val = AFUD_READ_INFO(afu); |
| afu->pp_irqs = AFUD_NUM_INTS_PER_PROC(val); |
| afu->max_procs_virtualised = AFUD_NUM_PROCS(val); |
| afu->crs_num = AFUD_NUM_CRS(val); |
| |
| if (AFUD_AFU_DIRECTED(val)) |
| afu->modes_supported |= CXL_MODE_DIRECTED; |
| if (AFUD_DEDICATED_PROCESS(val)) |
| afu->modes_supported |= CXL_MODE_DEDICATED; |
| if (AFUD_TIME_SLICED(val)) |
| afu->modes_supported |= CXL_MODE_TIME_SLICED; |
| |
| val = AFUD_READ_PPPSA(afu); |
| afu->pp_size = AFUD_PPPSA_LEN(val) * 4096; |
| afu->psa = AFUD_PPPSA_PSA(val); |
| if ((afu->pp_psa = AFUD_PPPSA_PP(val))) |
| afu->native->pp_offset = AFUD_READ_PPPSA_OFF(afu); |
| |
| val = AFUD_READ_CR(afu); |
| afu->crs_len = AFUD_CR_LEN(val) * 256; |
| afu->crs_offset = AFUD_READ_CR_OFF(afu); |
| |
| |
| /* eb_len is in multiple of 4K */ |
| afu->eb_len = AFUD_EB_LEN(AFUD_READ_EB(afu)) * 4096; |
| afu->eb_offset = AFUD_READ_EB_OFF(afu); |
| |
| /* eb_off is 4K aligned so lower 12 bits are always zero */ |
| if (EXTRACT_PPC_BITS(afu->eb_offset, 0, 11) != 0) { |
| dev_warn(&afu->dev, |
| "Invalid AFU error buffer offset %Lx\n", |
| afu->eb_offset); |
| dev_info(&afu->dev, |
| "Ignoring AFU error buffer in the descriptor\n"); |
| /* indicate that no afu buffer exists */ |
| afu->eb_len = 0; |
| } |
| |
| return 0; |
| } |
| |
| static int cxl_afu_descriptor_looks_ok(struct cxl_afu *afu) |
| { |
| int i, rc; |
| u32 val; |
| |
| if (afu->psa && afu->adapter->ps_size < |
| (afu->native->pp_offset + afu->pp_size*afu->max_procs_virtualised)) { |
| dev_err(&afu->dev, "per-process PSA can't fit inside the PSA!\n"); |
| return -ENODEV; |
| } |
| |
| if (afu->pp_psa && (afu->pp_size < PAGE_SIZE)) |
| dev_warn(&afu->dev, "AFU uses pp_size(%#016llx) < PAGE_SIZE per-process PSA!\n", afu->pp_size); |
| |
| for (i = 0; i < afu->crs_num; i++) { |
| rc = cxl_ops->afu_cr_read32(afu, i, 0, &val); |
| if (rc || val == 0) { |
| dev_err(&afu->dev, "ABORTING: AFU configuration record %i is invalid\n", i); |
| return -EINVAL; |
| } |
| } |
| |
| if ((afu->modes_supported & ~CXL_MODE_DEDICATED) && afu->max_procs_virtualised == 0) { |
| /* |
| * We could also check this for the dedicated process model |
| * since the architecture indicates it should be set to 1, but |
| * in that case we ignore the value and I'd rather not risk |
| * breaking any existing dedicated process AFUs that left it as |
| * 0 (not that I'm aware of any). It is clearly an error for an |
| * AFU directed AFU to set this to 0, and would have previously |
| * triggered a bug resulting in the maximum not being enforced |
| * at all since idr_alloc treats 0 as no maximum. |
| */ |
| dev_err(&afu->dev, "AFU does not support any processes\n"); |
| return -EINVAL; |
| } |
| |
| return 0; |
| } |
| |
| static int sanitise_afu_regs_psl9(struct cxl_afu *afu) |
| { |
| u64 reg; |
| |
| /* |
| * Clear out any regs that contain either an IVTE or address or may be |
| * waiting on an acknowledgment to try to be a bit safer as we bring |
| * it online |
| */ |
| reg = cxl_p2n_read(afu, CXL_AFU_Cntl_An); |
| if ((reg & CXL_AFU_Cntl_An_ES_MASK) != CXL_AFU_Cntl_An_ES_Disabled) { |
| dev_warn(&afu->dev, "WARNING: AFU was not disabled: %#016llx\n", reg); |
| if (cxl_ops->afu_reset(afu)) |
| return -EIO; |
| if (cxl_afu_disable(afu)) |
| return -EIO; |
| if (cxl_psl_purge(afu)) |
| return -EIO; |
| } |
| cxl_p1n_write(afu, CXL_PSL_SPAP_An, 0x0000000000000000); |
| cxl_p1n_write(afu, CXL_PSL_AMBAR_An, 0x0000000000000000); |
| reg = cxl_p2n_read(afu, CXL_PSL_DSISR_An); |
| if (reg) { |
| dev_warn(&afu->dev, "AFU had pending DSISR: %#016llx\n", reg); |
| if (reg & CXL_PSL9_DSISR_An_TF) |
| cxl_p2n_write(afu, CXL_PSL_TFC_An, CXL_PSL_TFC_An_AE); |
| else |
| cxl_p2n_write(afu, CXL_PSL_TFC_An, CXL_PSL_TFC_An_A); |
| } |
| if (afu->adapter->native->sl_ops->register_serr_irq) { |
| reg = cxl_p1n_read(afu, CXL_PSL_SERR_An); |
| if (reg) { |
| if (reg & ~0x000000007fffffff) |
| dev_warn(&afu->dev, "AFU had pending SERR: %#016llx\n", reg); |
| cxl_p1n_write(afu, CXL_PSL_SERR_An, reg & ~0xffff); |
| } |
| } |
| reg = cxl_p2n_read(afu, CXL_PSL_ErrStat_An); |
| if (reg) { |
| dev_warn(&afu->dev, "AFU had pending error status: %#016llx\n", reg); |
| cxl_p2n_write(afu, CXL_PSL_ErrStat_An, reg); |
| } |
| |
| return 0; |
| } |
| |
| static int sanitise_afu_regs_psl8(struct cxl_afu *afu) |
| { |
| u64 reg; |
| |
| /* |
| * Clear out any regs that contain either an IVTE or address or may be |
| * waiting on an acknowledgement to try to be a bit safer as we bring |
| * it online |
| */ |
| reg = cxl_p2n_read(afu, CXL_AFU_Cntl_An); |
| if ((reg & CXL_AFU_Cntl_An_ES_MASK) != CXL_AFU_Cntl_An_ES_Disabled) { |
| dev_warn(&afu->dev, "WARNING: AFU was not disabled: %#016llx\n", reg); |
| if (cxl_ops->afu_reset(afu)) |
| return -EIO; |
| if (cxl_afu_disable(afu)) |
| return -EIO; |
| if (cxl_psl_purge(afu)) |
| return -EIO; |
| } |
| cxl_p1n_write(afu, CXL_PSL_SPAP_An, 0x0000000000000000); |
| cxl_p1n_write(afu, CXL_PSL_IVTE_Limit_An, 0x0000000000000000); |
| cxl_p1n_write(afu, CXL_PSL_IVTE_Offset_An, 0x0000000000000000); |
| cxl_p1n_write(afu, CXL_PSL_AMBAR_An, 0x0000000000000000); |
| cxl_p1n_write(afu, CXL_PSL_SPOffset_An, 0x0000000000000000); |
| cxl_p1n_write(afu, CXL_HAURP_An, 0x0000000000000000); |
| cxl_p2n_write(afu, CXL_CSRP_An, 0x0000000000000000); |
| cxl_p2n_write(afu, CXL_AURP1_An, 0x0000000000000000); |
| cxl_p2n_write(afu, CXL_AURP0_An, 0x0000000000000000); |
| cxl_p2n_write(afu, CXL_SSTP1_An, 0x0000000000000000); |
| cxl_p2n_write(afu, CXL_SSTP0_An, 0x0000000000000000); |
| reg = cxl_p2n_read(afu, CXL_PSL_DSISR_An); |
| if (reg) { |
| dev_warn(&afu->dev, "AFU had pending DSISR: %#016llx\n", reg); |
| if (reg & CXL_PSL_DSISR_TRANS) |
| cxl_p2n_write(afu, CXL_PSL_TFC_An, CXL_PSL_TFC_An_AE); |
| else |
| cxl_p2n_write(afu, CXL_PSL_TFC_An, CXL_PSL_TFC_An_A); |
| } |
| if (afu->adapter->native->sl_ops->register_serr_irq) { |
| reg = cxl_p1n_read(afu, CXL_PSL_SERR_An); |
| if (reg) { |
| if (reg & ~0xffff) |
| dev_warn(&afu->dev, "AFU had pending SERR: %#016llx\n", reg); |
| cxl_p1n_write(afu, CXL_PSL_SERR_An, reg & ~0xffff); |
| } |
| } |
| reg = cxl_p2n_read(afu, CXL_PSL_ErrStat_An); |
| if (reg) { |
| dev_warn(&afu->dev, "AFU had pending error status: %#016llx\n", reg); |
| cxl_p2n_write(afu, CXL_PSL_ErrStat_An, reg); |
| } |
| |
| return 0; |
| } |
| |
| #define ERR_BUFF_MAX_COPY_SIZE PAGE_SIZE |
| /* |
| * afu_eb_read: |
| * Called from sysfs and reads the afu error info buffer. The h/w only supports |
| * 4/8 bytes aligned access. So in case the requested offset/count arent 8 byte |
| * aligned the function uses a bounce buffer which can be max PAGE_SIZE. |
| */ |
| ssize_t cxl_pci_afu_read_err_buffer(struct cxl_afu *afu, char *buf, |
| loff_t off, size_t count) |
| { |
| loff_t aligned_start, aligned_end; |
| size_t aligned_length; |
| void *tbuf; |
| const void __iomem *ebuf = afu->native->afu_desc_mmio + afu->eb_offset; |
| |
| if (count == 0 || off < 0 || (size_t)off >= afu->eb_len) |
| return 0; |
| |
| /* calculate aligned read window */ |
| count = min((size_t)(afu->eb_len - off), count); |
| aligned_start = round_down(off, 8); |
| aligned_end = round_up(off + count, 8); |
| aligned_length = aligned_end - aligned_start; |
| |
| /* max we can copy in one read is PAGE_SIZE */ |
| if (aligned_length > ERR_BUFF_MAX_COPY_SIZE) { |
| aligned_length = ERR_BUFF_MAX_COPY_SIZE; |
| count = ERR_BUFF_MAX_COPY_SIZE - (off & 0x7); |
| } |
| |
| /* use bounce buffer for copy */ |
| tbuf = (void *)__get_free_page(GFP_KERNEL); |
| if (!tbuf) |
| return -ENOMEM; |
| |
| /* perform aligned read from the mmio region */ |
| memcpy_fromio(tbuf, ebuf + aligned_start, aligned_length); |
| memcpy(buf, tbuf + (off & 0x7), count); |
| |
| free_page((unsigned long)tbuf); |
| |
| return count; |
| } |
| |
| static int pci_configure_afu(struct cxl_afu *afu, struct cxl *adapter, struct pci_dev *dev) |
| { |
| int rc; |
| |
| if ((rc = pci_map_slice_regs(afu, adapter, dev))) |
| return rc; |
| |
| if (adapter->native->sl_ops->sanitise_afu_regs) { |
| rc = adapter->native->sl_ops->sanitise_afu_regs(afu); |
| if (rc) |
| goto err1; |
| } |
| |
| /* We need to reset the AFU before we can read the AFU descriptor */ |
| if ((rc = cxl_ops->afu_reset(afu))) |
| goto err1; |
| |
| if (cxl_verbose) |
| dump_afu_descriptor(afu); |
| |
| if ((rc = cxl_read_afu_descriptor(afu))) |
| goto err1; |
| |
| if ((rc = cxl_afu_descriptor_looks_ok(afu))) |
| goto err1; |
| |
| if (adapter->native->sl_ops->afu_regs_init) |
| if ((rc = adapter->native->sl_ops->afu_regs_init(afu))) |
| goto err1; |
| |
| if (adapter->native->sl_ops->register_serr_irq) |
| if ((rc = adapter->native->sl_ops->register_serr_irq(afu))) |
| goto err1; |
| |
| if ((rc = cxl_native_register_psl_irq(afu))) |
| goto err2; |
| |
| atomic_set(&afu->configured_state, 0); |
| return 0; |
| |
| err2: |
| if (adapter->native->sl_ops->release_serr_irq) |
| adapter->native->sl_ops->release_serr_irq(afu); |
| err1: |
| pci_unmap_slice_regs(afu); |
| return rc; |
| } |
| |
| static void pci_deconfigure_afu(struct cxl_afu *afu) |
| { |
| /* |
| * It's okay to deconfigure when AFU is already locked, otherwise wait |
| * until there are no readers |
| */ |
| if (atomic_read(&afu->configured_state) != -1) { |
| while (atomic_cmpxchg(&afu->configured_state, 0, -1) != -1) |
| schedule(); |
| } |
| cxl_native_release_psl_irq(afu); |
| if (afu->adapter->native->sl_ops->release_serr_irq) |
| afu->adapter->native->sl_ops->release_serr_irq(afu); |
| pci_unmap_slice_regs(afu); |
| } |
| |
| static int pci_init_afu(struct cxl *adapter, int slice, struct pci_dev *dev) |
| { |
| struct cxl_afu *afu; |
| int rc = -ENOMEM; |
| |
| afu = cxl_alloc_afu(adapter, slice); |
| if (!afu) |
| return -ENOMEM; |
| |
| afu->native = kzalloc(sizeof(struct cxl_afu_native), GFP_KERNEL); |
| if (!afu->native) |
| goto err_free_afu; |
| |
| mutex_init(&afu->native->spa_mutex); |
| |
| rc = dev_set_name(&afu->dev, "afu%i.%i", adapter->adapter_num, slice); |
| if (rc) |
| goto err_free_native; |
| |
| rc = pci_configure_afu(afu, adapter, dev); |
| if (rc) |
| goto err_free_native; |
| |
| /* Don't care if this fails */ |
| cxl_debugfs_afu_add(afu); |
| |
| /* |
| * After we call this function we must not free the afu directly, even |
| * if it returns an error! |
| */ |
| if ((rc = cxl_register_afu(afu))) |
| goto err_put_dev; |
| |
| if ((rc = cxl_sysfs_afu_add(afu))) |
| goto err_del_dev; |
| |
| adapter->afu[afu->slice] = afu; |
| |
| if ((rc = cxl_pci_vphb_add(afu))) |
| dev_info(&afu->dev, "Can't register vPHB\n"); |
| |
| return 0; |
| |
| err_del_dev: |
| device_del(&afu->dev); |
| err_put_dev: |
| pci_deconfigure_afu(afu); |
| cxl_debugfs_afu_remove(afu); |
| put_device(&afu->dev); |
| return rc; |
| |
| err_free_native: |
| kfree(afu->native); |
| err_free_afu: |
| kfree(afu); |
| return rc; |
| |
| } |
| |
| static void cxl_pci_remove_afu(struct cxl_afu *afu) |
| { |
| pr_devel("%s\n", __func__); |
| |
| if (!afu) |
| return; |
| |
| cxl_pci_vphb_remove(afu); |
| cxl_sysfs_afu_remove(afu); |
| cxl_debugfs_afu_remove(afu); |
| |
| spin_lock(&afu->adapter->afu_list_lock); |
| afu->adapter->afu[afu->slice] = NULL; |
| spin_unlock(&afu->adapter->afu_list_lock); |
| |
| cxl_context_detach_all(afu); |
| cxl_ops->afu_deactivate_mode(afu, afu->current_mode); |
| |
| pci_deconfigure_afu(afu); |
| device_unregister(&afu->dev); |
| } |
| |
| int cxl_pci_reset(struct cxl *adapter) |
| { |
| struct pci_dev *dev = to_pci_dev(adapter->dev.parent); |
| int rc; |
| |
| if (adapter->perst_same_image) { |
| dev_warn(&dev->dev, |
| "cxl: refusing to reset/reflash when perst_reloads_same_image is set.\n"); |
| return -EINVAL; |
| } |
| |
| dev_info(&dev->dev, "CXL reset\n"); |
| |
| /* |
| * The adapter is about to be reset, so ignore errors. |
| */ |
| cxl_data_cache_flush(adapter); |
| |
| /* pcie_warm_reset requests a fundamental pci reset which includes a |
| * PERST assert/deassert. PERST triggers a loading of the image |
| * if "user" or "factory" is selected in sysfs */ |
| if ((rc = pci_set_pcie_reset_state(dev, pcie_warm_reset))) { |
| dev_err(&dev->dev, "cxl: pcie_warm_reset failed\n"); |
| return rc; |
| } |
| |
| return rc; |
| } |
| |
| static int cxl_map_adapter_regs(struct cxl *adapter, struct pci_dev *dev) |
| { |
| if (pci_request_region(dev, 2, "priv 2 regs")) |
| goto err1; |
| if (pci_request_region(dev, 0, "priv 1 regs")) |
| goto err2; |
| |
| pr_devel("cxl_map_adapter_regs: p1: %#016llx %#llx, p2: %#016llx %#llx", |
| p1_base(dev), p1_size(dev), p2_base(dev), p2_size(dev)); |
| |
| if (!(adapter->native->p1_mmio = ioremap(p1_base(dev), p1_size(dev)))) |
| goto err3; |
| |
| if (!(adapter->native->p2_mmio = ioremap(p2_base(dev), p2_size(dev)))) |
| goto err4; |
| |
| return 0; |
| |
| err4: |
| iounmap(adapter->native->p1_mmio); |
| adapter->native->p1_mmio = NULL; |
| err3: |
| pci_release_region(dev, 0); |
| err2: |
| pci_release_region(dev, 2); |
| err1: |
| return -ENOMEM; |
| } |
| |
| static void cxl_unmap_adapter_regs(struct cxl *adapter) |
| { |
| if (adapter->native->p1_mmio) { |
| iounmap(adapter->native->p1_mmio); |
| adapter->native->p1_mmio = NULL; |
| pci_release_region(to_pci_dev(adapter->dev.parent), 2); |
| } |
| if (adapter->native->p2_mmio) { |
| iounmap(adapter->native->p2_mmio); |
| adapter->native->p2_mmio = NULL; |
| pci_release_region(to_pci_dev(adapter->dev.parent), 0); |
| } |
| } |
| |
| static int cxl_read_vsec(struct cxl *adapter, struct pci_dev *dev) |
| { |
| int vsec; |
| u32 afu_desc_off, afu_desc_size; |
| u32 ps_off, ps_size; |
| u16 vseclen; |
| u8 image_state; |
| |
| if (!(vsec = find_cxl_vsec(dev))) { |
| dev_err(&dev->dev, "ABORTING: CXL VSEC not found!\n"); |
| return -ENODEV; |
| } |
| |
| CXL_READ_VSEC_LENGTH(dev, vsec, &vseclen); |
| if (vseclen < CXL_VSEC_MIN_SIZE) { |
| dev_err(&dev->dev, "ABORTING: CXL VSEC too short\n"); |
| return -EINVAL; |
| } |
| |
| CXL_READ_VSEC_STATUS(dev, vsec, &adapter->vsec_status); |
| CXL_READ_VSEC_PSL_REVISION(dev, vsec, &adapter->psl_rev); |
| CXL_READ_VSEC_CAIA_MAJOR(dev, vsec, &adapter->caia_major); |
| CXL_READ_VSEC_CAIA_MINOR(dev, vsec, &adapter->caia_minor); |
| CXL_READ_VSEC_BASE_IMAGE(dev, vsec, &adapter->base_image); |
| CXL_READ_VSEC_IMAGE_STATE(dev, vsec, &image_state); |
| adapter->user_image_loaded = !!(image_state & CXL_VSEC_USER_IMAGE_LOADED); |
| adapter->perst_select_user = !!(image_state & CXL_VSEC_USER_IMAGE_LOADED); |
| adapter->perst_loads_image = !!(image_state & CXL_VSEC_PERST_LOADS_IMAGE); |
| |
| CXL_READ_VSEC_NAFUS(dev, vsec, &adapter->slices); |
| CXL_READ_VSEC_AFU_DESC_OFF(dev, vsec, &afu_desc_off); |
| CXL_READ_VSEC_AFU_DESC_SIZE(dev, vsec, &afu_desc_size); |
| CXL_READ_VSEC_PS_OFF(dev, vsec, &ps_off); |
| CXL_READ_VSEC_PS_SIZE(dev, vsec, &ps_size); |
| |
| /* Convert everything to bytes, because there is NO WAY I'd look at the |
| * code a month later and forget what units these are in ;-) */ |
| adapter->native->ps_off = ps_off * 64 * 1024; |
| adapter->ps_size = ps_size * 64 * 1024; |
| adapter->native->afu_desc_off = afu_desc_off * 64 * 1024; |
| adapter->native->afu_desc_size = afu_desc_size * 64 * 1024; |
| |
| /* Total IRQs - 1 PSL ERROR - #AFU*(1 slice error + 1 DSI) */ |
| adapter->user_irqs = pnv_cxl_get_irq_count(dev) - 1 - 2*adapter->slices; |
| |
| return 0; |
| } |
| |
| /* |
| * Workaround a PCIe Host Bridge defect on some cards, that can cause |
| * malformed Transaction Layer Packet (TLP) errors to be erroneously |
| * reported. Mask this error in the Uncorrectable Error Mask Register. |
| * |
| * The upper nibble of the PSL revision is used to distinguish between |
| * different cards. The affected ones have it set to 0. |
| */ |
| static void cxl_fixup_malformed_tlp(struct cxl *adapter, struct pci_dev *dev) |
| { |
| int aer; |
| u32 data; |
| |
| if (adapter->psl_rev & 0xf000) |
| return; |
| if (!(aer = pci_find_ext_capability(dev, PCI_EXT_CAP_ID_ERR))) |
| return; |
| pci_read_config_dword(dev, aer + PCI_ERR_UNCOR_MASK, &data); |
| if (data & PCI_ERR_UNC_MALF_TLP) |
| if (data & PCI_ERR_UNC_INTN) |
| return; |
| data |= PCI_ERR_UNC_MALF_TLP; |
| data |= PCI_ERR_UNC_INTN; |
| pci_write_config_dword(dev, aer + PCI_ERR_UNCOR_MASK, data); |
| } |
| |
| static bool cxl_compatible_caia_version(struct cxl *adapter) |
| { |
| if (cxl_is_power8() && (adapter->caia_major == 1)) |
| return true; |
| |
| if (cxl_is_power9() && (adapter->caia_major == 2)) |
| return true; |
| |
| return false; |
| } |
| |
| static int cxl_vsec_looks_ok(struct cxl *adapter, struct pci_dev *dev) |
| { |
| if (adapter->vsec_status & CXL_STATUS_SECOND_PORT) |
| return -EBUSY; |
| |
| if (adapter->vsec_status & CXL_UNSUPPORTED_FEATURES) { |
| dev_err(&dev->dev, "ABORTING: CXL requires unsupported features\n"); |
| return -EINVAL; |
| } |
| |
| if (!cxl_compatible_caia_version(adapter)) { |
| dev_info(&dev->dev, "Ignoring card. PSL type is not supported (caia version: %d)\n", |
| adapter->caia_major); |
| return -ENODEV; |
| } |
| |
| if (!adapter->slices) { |
| /* Once we support dynamic reprogramming we can use the card if |
| * it supports loadable AFUs */ |
| dev_err(&dev->dev, "ABORTING: Device has no AFUs\n"); |
| return -EINVAL; |
| } |
| |
| if (!adapter->native->afu_desc_off || !adapter->native->afu_desc_size) { |
| dev_err(&dev->dev, "ABORTING: VSEC shows no AFU descriptors\n"); |
| return -EINVAL; |
| } |
| |
| if (adapter->ps_size > p2_size(dev) - adapter->native->ps_off) { |
| dev_err(&dev->dev, "ABORTING: Problem state size larger than " |
| "available in BAR2: 0x%llx > 0x%llx\n", |
| adapter->ps_size, p2_size(dev) - adapter->native->ps_off); |
| return -EINVAL; |
| } |
| |
| return 0; |
| } |
| |
| ssize_t cxl_pci_read_adapter_vpd(struct cxl *adapter, void *buf, size_t len) |
| { |
| return pci_read_vpd(to_pci_dev(adapter->dev.parent), 0, len, buf); |
| } |
| |
| static void cxl_release_adapter(struct device *dev) |
| { |
| struct cxl *adapter = to_cxl_adapter(dev); |
| |
| pr_devel("cxl_release_adapter\n"); |
| |
| cxl_remove_adapter_nr(adapter); |
| |
| kfree(adapter->native); |
| kfree(adapter); |
| } |
| |
| #define CXL_PSL_ErrIVTE_tberror (0x1ull << (63-31)) |
| |
| static int sanitise_adapter_regs(struct cxl *adapter) |
| { |
| int rc = 0; |
| |
| /* Clear PSL tberror bit by writing 1 to it */ |
| cxl_p1_write(adapter, CXL_PSL_ErrIVTE, CXL_PSL_ErrIVTE_tberror); |
| |
| if (adapter->native->sl_ops->invalidate_all) { |
| /* do not invalidate ERAT entries when not reloading on PERST */ |
| if (cxl_is_power9() && (adapter->perst_loads_image)) |
| return 0; |
| rc = adapter->native->sl_ops->invalidate_all(adapter); |
| } |
| |
| return rc; |
| } |
| |
| /* This should contain *only* operations that can safely be done in |
| * both creation and recovery. |
| */ |
| static int cxl_configure_adapter(struct cxl *adapter, struct pci_dev *dev) |
| { |
| int rc; |
| |
| adapter->dev.parent = &dev->dev; |
| adapter->dev.release = cxl_release_adapter; |
| pci_set_drvdata(dev, adapter); |
| |
| rc = pci_enable_device(dev); |
| if (rc) { |
| dev_err(&dev->dev, "pci_enable_device failed: %i\n", rc); |
| return rc; |
| } |
| |
| if ((rc = cxl_read_vsec(adapter, dev))) |
| return rc; |
| |
| if ((rc = cxl_vsec_looks_ok(adapter, dev))) |
| return rc; |
| |
| cxl_fixup_malformed_tlp(adapter, dev); |
| |
| if ((rc = setup_cxl_bars(dev))) |
| return rc; |
| |
| if ((rc = switch_card_to_cxl(dev))) |
| return rc; |
| |
| if ((rc = cxl_update_image_control(adapter))) |
| return rc; |
| |
| if ((rc = cxl_map_adapter_regs(adapter, dev))) |
| return rc; |
| |
| if ((rc = sanitise_adapter_regs(adapter))) |
| goto err; |
| |
| if ((rc = adapter->native->sl_ops->adapter_regs_init(adapter, dev))) |
| goto err; |
| |
| /* Required for devices using CAPP DMA mode, harmless for others */ |
| pci_set_master(dev); |
| |
| adapter->tunneled_ops_supported = false; |
| |
| if (cxl_is_power9()) { |
| if (pnv_pci_set_tunnel_bar(dev, 0x00020000E0000000ull, 1)) |
| dev_info(&dev->dev, "Tunneled operations unsupported\n"); |
| else |
| adapter->tunneled_ops_supported = true; |
| } |
| |
| if ((rc = pnv_phb_to_cxl_mode(dev, adapter->native->sl_ops->capi_mode))) |
| goto err; |
| |
| /* If recovery happened, the last step is to turn on snooping. |
| * In the non-recovery case this has no effect */ |
| if ((rc = pnv_phb_to_cxl_mode(dev, OPAL_PHB_CAPI_MODE_SNOOP_ON))) |
| goto err; |
| |
| /* Ignore error, adapter init is not dependant on timebase sync */ |
| cxl_setup_psl_timebase(adapter, dev); |
| |
| if ((rc = cxl_native_register_psl_err_irq(adapter))) |
| goto err; |
| |
| return 0; |
| |
| err: |
| cxl_unmap_adapter_regs(adapter); |
| return rc; |
| |
| } |
| |
| static void cxl_deconfigure_adapter(struct cxl *adapter) |
| { |
| struct pci_dev *pdev = to_pci_dev(adapter->dev.parent); |
| |
| if (cxl_is_power9()) |
| pnv_pci_set_tunnel_bar(pdev, 0x00020000E0000000ull, 0); |
| |
| cxl_native_release_psl_err_irq(adapter); |
| cxl_unmap_adapter_regs(adapter); |
| |
| pci_disable_device(pdev); |
| } |
| |
| static void cxl_stop_trace_psl9(struct cxl *adapter) |
| { |
| int traceid; |
| u64 trace_state, trace_mask; |
| struct pci_dev *dev = to_pci_dev(adapter->dev.parent); |
| |
| /* read each tracearray state and issue mmio to stop them is needed */ |
| for (traceid = 0; traceid <= CXL_PSL9_TRACEID_MAX; ++traceid) { |
| trace_state = cxl_p1_read(adapter, CXL_PSL9_CTCCFG); |
| trace_mask = (0x3ULL << (62 - traceid * 2)); |
| trace_state = (trace_state & trace_mask) >> (62 - traceid * 2); |
| dev_dbg(&dev->dev, "cxl: Traceid-%d trace_state=0x%0llX\n", |
| traceid, trace_state); |
| |
| /* issue mmio if the trace array isn't in FIN state */ |
| if (trace_state != CXL_PSL9_TRACESTATE_FIN) |
| cxl_p1_write(adapter, CXL_PSL9_TRACECFG, |
| 0x8400000000000000ULL | traceid); |
| } |
| } |
| |
| static void cxl_stop_trace_psl8(struct cxl *adapter) |
| { |
| int slice; |
| |
| /* Stop the trace */ |
| cxl_p1_write(adapter, CXL_PSL_TRACE, 0x8000000000000017LL); |
| |
| /* Stop the slice traces */ |
| spin_lock(&adapter->afu_list_lock); |
| for (slice = 0; slice < adapter->slices; slice++) { |
| if (adapter->afu[slice]) |
| cxl_p1n_write(adapter->afu[slice], CXL_PSL_SLICE_TRACE, |
| 0x8000000000000000LL); |
| } |
| spin_unlock(&adapter->afu_list_lock); |
| } |
| |
| static const struct cxl_service_layer_ops psl9_ops = { |
| .adapter_regs_init = init_implementation_adapter_regs_psl9, |
| .invalidate_all = cxl_invalidate_all_psl9, |
| .afu_regs_init = init_implementation_afu_regs_psl9, |
| .sanitise_afu_regs = sanitise_afu_regs_psl9, |
| .register_serr_irq = cxl_native_register_serr_irq, |
| .release_serr_irq = cxl_native_release_serr_irq, |
| .handle_interrupt = cxl_irq_psl9, |
| .fail_irq = cxl_fail_irq_psl, |
| .activate_dedicated_process = cxl_activate_dedicated_process_psl9, |
| .attach_afu_directed = cxl_attach_afu_directed_psl9, |
| .attach_dedicated_process = cxl_attach_dedicated_process_psl9, |
| .update_dedicated_ivtes = cxl_update_dedicated_ivtes_psl9, |
| .debugfs_add_adapter_regs = cxl_debugfs_add_adapter_regs_psl9, |
| .debugfs_add_afu_regs = cxl_debugfs_add_afu_regs_psl9, |
| .psl_irq_dump_registers = cxl_native_irq_dump_regs_psl9, |
| .err_irq_dump_registers = cxl_native_err_irq_dump_regs_psl9, |
| .debugfs_stop_trace = cxl_stop_trace_psl9, |
| .timebase_read = timebase_read_psl9, |
| .capi_mode = OPAL_PHB_CAPI_MODE_CAPI, |
| .needs_reset_before_disable = true, |
| }; |
| |
| static const struct cxl_service_layer_ops psl8_ops = { |
| .adapter_regs_init = init_implementation_adapter_regs_psl8, |
| .invalidate_all = cxl_invalidate_all_psl8, |
| .afu_regs_init = init_implementation_afu_regs_psl8, |
| .sanitise_afu_regs = sanitise_afu_regs_psl8, |
| .register_serr_irq = cxl_native_register_serr_irq, |
| .release_serr_irq = cxl_native_release_serr_irq, |
| .handle_interrupt = cxl_irq_psl8, |
| .fail_irq = cxl_fail_irq_psl, |
| .activate_dedicated_process = cxl_activate_dedicated_process_psl8, |
| .attach_afu_directed = cxl_attach_afu_directed_psl8, |
| .attach_dedicated_process = cxl_attach_dedicated_process_psl8, |
| .update_dedicated_ivtes = cxl_update_dedicated_ivtes_psl8, |
| .debugfs_add_adapter_regs = cxl_debugfs_add_adapter_regs_psl8, |
| .debugfs_add_afu_regs = cxl_debugfs_add_afu_regs_psl8, |
| .psl_irq_dump_registers = cxl_native_irq_dump_regs_psl8, |
| .err_irq_dump_registers = cxl_native_err_irq_dump_regs_psl8, |
| .debugfs_stop_trace = cxl_stop_trace_psl8, |
| .write_timebase_ctrl = write_timebase_ctrl_psl8, |
| .timebase_read = timebase_read_psl8, |
| .capi_mode = OPAL_PHB_CAPI_MODE_CAPI, |
| .needs_reset_before_disable = true, |
| }; |
| |
| static void set_sl_ops(struct cxl *adapter, struct pci_dev *dev) |
| { |
| if (cxl_is_power8()) { |
| dev_info(&dev->dev, "Device uses a PSL8\n"); |
| adapter->native->sl_ops = &psl8_ops; |
| } else { |
| dev_info(&dev->dev, "Device uses a PSL9\n"); |
| adapter->native->sl_ops = &psl9_ops; |
| } |
| } |
| |
| |
| static struct cxl *cxl_pci_init_adapter(struct pci_dev *dev) |
| { |
| struct cxl *adapter; |
| int rc; |
| |
| adapter = cxl_alloc_adapter(); |
| if (!adapter) |
| return ERR_PTR(-ENOMEM); |
| |
| adapter->native = kzalloc(sizeof(struct cxl_native), GFP_KERNEL); |
| if (!adapter->native) { |
| rc = -ENOMEM; |
| goto err_release; |
| } |
| |
| set_sl_ops(adapter, dev); |
| |
| /* Set defaults for parameters which need to persist over |
| * configure/reconfigure |
| */ |
| adapter->perst_loads_image = true; |
| adapter->perst_same_image = false; |
| |
| rc = cxl_configure_adapter(adapter, dev); |
| if (rc) { |
| pci_disable_device(dev); |
| goto err_release; |
| } |
| |
| /* Don't care if this one fails: */ |
| cxl_debugfs_adapter_add(adapter); |
| |
| /* |
| * After we call this function we must not free the adapter directly, |
| * even if it returns an error! |
| */ |
| if ((rc = cxl_register_adapter(adapter))) |
| goto err_put_dev; |
| |
| if ((rc = cxl_sysfs_adapter_add(adapter))) |
| goto err_del_dev; |
| |
| /* Release the context lock as adapter is configured */ |
| cxl_adapter_context_unlock(adapter); |
| |
| return adapter; |
| |
| err_del_dev: |
| device_del(&adapter->dev); |
| err_put_dev: |
| /* This should mirror cxl_remove_adapter, except without the |
| * sysfs parts |
| */ |
| cxl_debugfs_adapter_remove(adapter); |
| cxl_deconfigure_adapter(adapter); |
| put_device(&adapter->dev); |
| return ERR_PTR(rc); |
| |
| err_release: |
| cxl_release_adapter(&adapter->dev); |
| return ERR_PTR(rc); |
| } |
| |
| static void cxl_pci_remove_adapter(struct cxl *adapter) |
| { |
| pr_devel("cxl_remove_adapter\n"); |
| |
| cxl_sysfs_adapter_remove(adapter); |
| cxl_debugfs_adapter_remove(adapter); |
| |
| /* |
| * Flush adapter datacache as its about to be removed. |
| */ |
| cxl_data_cache_flush(adapter); |
| |
| cxl_deconfigure_adapter(adapter); |
| |
| device_unregister(&adapter->dev); |
| } |
| |
| #define CXL_MAX_PCIEX_PARENT 2 |
| |
| int cxl_slot_is_switched(struct pci_dev *dev) |
| { |
| struct device_node *np; |
| int depth = 0; |
| |
| if (!(np = pci_device_to_OF_node(dev))) { |
| pr_err("cxl: np = NULL\n"); |
| return -ENODEV; |
| } |
| of_node_get(np); |
| while (np) { |
| np = of_get_next_parent(np); |
| if (!of_node_is_type(np, "pciex")) |
| break; |
| depth++; |
| } |
| of_node_put(np); |
| return (depth > CXL_MAX_PCIEX_PARENT); |
| } |
| |
| static int cxl_probe(struct pci_dev *dev, const struct pci_device_id *id) |
| { |
| struct cxl *adapter; |
| int slice; |
| int rc; |
| |
| if (cxl_pci_is_vphb_device(dev)) { |
| dev_dbg(&dev->dev, "cxl_init_adapter: Ignoring cxl vphb device\n"); |
| return -ENODEV; |
| } |
| |
| if (cxl_slot_is_switched(dev)) { |
| dev_info(&dev->dev, "Ignoring card on incompatible PCI slot\n"); |
| return -ENODEV; |
| } |
| |
| if (cxl_is_power9() && !radix_enabled()) { |
| dev_info(&dev->dev, "Only Radix mode supported\n"); |
| return -ENODEV; |
| } |
| |
| if (cxl_verbose) |
| dump_cxl_config_space(dev); |
| |
| adapter = cxl_pci_init_adapter(dev); |
| if (IS_ERR(adapter)) { |
| dev_err(&dev->dev, "cxl_init_adapter failed: %li\n", PTR_ERR(adapter)); |
| return PTR_ERR(adapter); |
| } |
| |
| for (slice = 0; slice < adapter->slices; slice++) { |
| if ((rc = pci_init_afu(adapter, slice, dev))) { |
| dev_err(&dev->dev, "AFU %i failed to initialise: %i\n", slice, rc); |
| continue; |
| } |
| |
| rc = cxl_afu_select_best_mode(adapter->afu[slice]); |
| if (rc) |
| dev_err(&dev->dev, "AFU %i failed to start: %i\n", slice, rc); |
| } |
| |
| return 0; |
| } |
| |
| static void cxl_remove(struct pci_dev *dev) |
| { |
| struct cxl *adapter = pci_get_drvdata(dev); |
| struct cxl_afu *afu; |
| int i; |
| |
| /* |
| * Lock to prevent someone grabbing a ref through the adapter list as |
| * we are removing it |
| */ |
| for (i = 0; i < adapter->slices; i++) { |
| afu = adapter->afu[i]; |
| cxl_pci_remove_afu(afu); |
| } |
| cxl_pci_remove_adapter(adapter); |
| } |
| |
| static pci_ers_result_t cxl_vphb_error_detected(struct cxl_afu *afu, |
| pci_channel_state_t state) |
| { |
| struct pci_dev *afu_dev; |
| struct pci_driver *afu_drv; |
| const struct pci_error_handlers *err_handler; |
| pci_ers_result_t result = PCI_ERS_RESULT_NEED_RESET; |
| pci_ers_result_t afu_result = PCI_ERS_RESULT_NEED_RESET; |
| |
| /* There should only be one entry, but go through the list |
| * anyway |
| */ |
| if (afu == NULL || afu->phb == NULL) |
| return result; |
| |
| list_for_each_entry(afu_dev, &afu->phb->bus->devices, bus_list) { |
| afu_drv = to_pci_driver(afu_dev->dev.driver); |
| if (!afu_drv) |
| continue; |
| |
| afu_dev->error_state = state; |
| |
| err_handler = afu_drv->err_handler; |
| if (err_handler) |
| afu_result = err_handler->error_detected(afu_dev, |
| state); |
| /* Disconnect trumps all, NONE trumps NEED_RESET */ |
| if (afu_result == PCI_ERS_RESULT_DISCONNECT) |
| result = PCI_ERS_RESULT_DISCONNECT; |
| else if ((afu_result == PCI_ERS_RESULT_NONE) && |
| (result == PCI_ERS_RESULT_NEED_RESET)) |
| result = PCI_ERS_RESULT_NONE; |
| } |
| return result; |
| } |
| |
| static pci_ers_result_t cxl_pci_error_detected(struct pci_dev *pdev, |
| pci_channel_state_t state) |
| { |
| struct cxl *adapter = pci_get_drvdata(pdev); |
| struct cxl_afu *afu; |
| pci_ers_result_t result = PCI_ERS_RESULT_NEED_RESET; |
| pci_ers_result_t afu_result = PCI_ERS_RESULT_NEED_RESET; |
| int i; |
| |
| /* At this point, we could still have an interrupt pending. |
| * Let's try to get them out of the way before they do |
| * anything we don't like. |
| */ |
| schedule(); |
| |
| /* If we're permanently dead, give up. */ |
| if (state == pci_channel_io_perm_failure) { |
| spin_lock(&adapter->afu_list_lock); |
| for (i = 0; i < adapter->slices; i++) { |
| afu = adapter->afu[i]; |
| /* |
| * Tell the AFU drivers; but we don't care what they |
| * say, we're going away. |
| */ |
| cxl_vphb_error_detected(afu, state); |
| } |
| spin_unlock(&adapter->afu_list_lock); |
| return PCI_ERS_RESULT_DISCONNECT; |
| } |
| |
| /* Are we reflashing? |
| * |
| * If we reflash, we could come back as something entirely |
| * different, including a non-CAPI card. As such, by default |
| * we don't participate in the process. We'll be unbound and |
| * the slot re-probed. (TODO: check EEH doesn't blindly rebind |
| * us!) |
| * |
| * However, this isn't the entire story: for reliablity |
| * reasons, we usually want to reflash the FPGA on PERST in |
| * order to get back to a more reliable known-good state. |
| * |
| * This causes us a bit of a problem: if we reflash we can't |
| * trust that we'll come back the same - we could have a new |
| * image and been PERSTed in order to load that |
| * image. However, most of the time we actually *will* come |
| * back the same - for example a regular EEH event. |
| * |
| * Therefore, we allow the user to assert that the image is |
| * indeed the same and that we should continue on into EEH |
| * anyway. |
| */ |
| if (adapter->perst_loads_image && !adapter->perst_same_image) { |
| /* TODO take the PHB out of CXL mode */ |
| dev_info(&pdev->dev, "reflashing, so opting out of EEH!\n"); |
| return PCI_ERS_RESULT_NONE; |
| } |
| |
| /* |
| * At this point, we want to try to recover. We'll always |
| * need a complete slot reset: we don't trust any other reset. |
| * |
| * Now, we go through each AFU: |
| * - We send the driver, if bound, an error_detected callback. |
| * We expect it to clean up, but it can also tell us to give |
| * up and permanently detach the card. To simplify things, if |
| * any bound AFU driver doesn't support EEH, we give up on EEH. |
| * |
| * - We detach all contexts associated with the AFU. This |
| * does not free them, but puts them into a CLOSED state |
| * which causes any the associated files to return useful |
| * errors to userland. It also unmaps, but does not free, |
| * any IRQs. |
| * |
| * - We clean up our side: releasing and unmapping resources we hold |
| * so we can wire them up again when the hardware comes back up. |
| * |
| * Driver authors should note: |
| * |
| * - Any contexts you create in your kernel driver (except |
| * those associated with anonymous file descriptors) are |
| * your responsibility to free and recreate. Likewise with |
| * any attached resources. |
| * |
| * - We will take responsibility for re-initialising the |
| * device context (the one set up for you in |
| * cxl_pci_enable_device_hook and accessed through |
| * cxl_get_context). If you've attached IRQs or other |
| * resources to it, they remains yours to free. |
| * |
| * You can call the same functions to release resources as you |
| * normally would: we make sure that these functions continue |
| * to work when the hardware is down. |
| * |
| * Two examples: |
| * |
| * 1) If you normally free all your resources at the end of |
| * each request, or if you use anonymous FDs, your |
| * error_detected callback can simply set a flag to tell |
| * your driver not to start any new calls. You can then |
| * clear the flag in the resume callback. |
| * |
| * 2) If you normally allocate your resources on startup: |
| * * Set a flag in error_detected as above. |
| * * Let CXL detach your contexts. |
| * * In slot_reset, free the old resources and allocate new ones. |
| * * In resume, clear the flag to allow things to start. |
| */ |
| |
| /* Make sure no one else changes the afu list */ |
| spin_lock(&adapter->afu_list_lock); |
| |
| for (i = 0; i < adapter->slices; i++) { |
| afu = adapter->afu[i]; |
| |
| if (afu == NULL) |
| continue; |
| |
| afu_result = cxl_vphb_error_detected(afu, state); |
| cxl_context_detach_all(afu); |
| cxl_ops->afu_deactivate_mode(afu, afu->current_mode); |
| pci_deconfigure_afu(afu); |
| |
| /* Disconnect trumps all, NONE trumps NEED_RESET */ |
| if (afu_result == PCI_ERS_RESULT_DISCONNECT) |
| result = PCI_ERS_RESULT_DISCONNECT; |
| else if ((afu_result == PCI_ERS_RESULT_NONE) && |
| (result == PCI_ERS_RESULT_NEED_RESET)) |
| result = PCI_ERS_RESULT_NONE; |
| } |
| spin_unlock(&adapter->afu_list_lock); |
| |
| /* should take the context lock here */ |
| if (cxl_adapter_context_lock(adapter) != 0) |
| dev_warn(&adapter->dev, |
| "Couldn't take context lock with %d active-contexts\n", |
| atomic_read(&adapter->contexts_num)); |
| |
| cxl_deconfigure_adapter(adapter); |
| |
| return result; |
| } |
| |
| static pci_ers_result_t cxl_pci_slot_reset(struct pci_dev *pdev) |
| { |
| struct cxl *adapter = pci_get_drvdata(pdev); |
| struct cxl_afu *afu; |
| struct cxl_context *ctx; |
| struct pci_dev *afu_dev; |
| struct pci_driver *afu_drv; |
| const struct pci_error_handlers *err_handler; |
| pci_ers_result_t afu_result = PCI_ERS_RESULT_RECOVERED; |
| pci_ers_result_t result = PCI_ERS_RESULT_RECOVERED; |
| int i; |
| |
| if (cxl_configure_adapter(adapter, pdev)) |
| goto err; |
| |
| /* |
| * Unlock context activation for the adapter. Ideally this should be |
| * done in cxl_pci_resume but cxlflash module tries to activate the |
| * master context as part of slot_reset callback. |
| */ |
| cxl_adapter_context_unlock(adapter); |
| |
| spin_lock(&adapter->afu_list_lock); |
| for (i = 0; i < adapter->slices; i++) { |
| afu = adapter->afu[i]; |
| |
| if (afu == NULL) |
| continue; |
| |
| if (pci_configure_afu(afu, adapter, pdev)) |
| goto err_unlock; |
| |
| if (cxl_afu_select_best_mode(afu)) |
| goto err_unlock; |
| |
| if (afu->phb == NULL) |
| continue; |
| |
| list_for_each_entry(afu_dev, &afu->phb->bus->devices, bus_list) { |
| /* Reset the device context. |
| * TODO: make this less disruptive |
| */ |
| ctx = cxl_get_context(afu_dev); |
| |
| if (ctx && cxl_release_context(ctx)) |
| goto err_unlock; |
| |
| ctx = cxl_dev_context_init(afu_dev); |
| if (IS_ERR(ctx)) |
| goto err_unlock; |
| |
| afu_dev->dev.archdata.cxl_ctx = ctx; |
| |
| if (cxl_ops->afu_check_and_enable(afu)) |
| goto err_unlock; |
| |
| afu_dev->error_state = pci_channel_io_normal; |
| |
| /* If there's a driver attached, allow it to |
| * chime in on recovery. Drivers should check |
| * if everything has come back OK, but |
| * shouldn't start new work until we call |
| * their resume function. |
| */ |
| afu_drv = to_pci_driver(afu_dev->dev.driver); |
| if (!afu_drv) |
| continue; |
| |
| err_handler = afu_drv->err_handler; |
| if (err_handler && err_handler->slot_reset) |
| afu_result = err_handler->slot_reset(afu_dev); |
| |
| if (afu_result == PCI_ERS_RESULT_DISCONNECT) |
| result = PCI_ERS_RESULT_DISCONNECT; |
| } |
| } |
| |
| spin_unlock(&adapter->afu_list_lock); |
| return result; |
| |
| err_unlock: |
| spin_unlock(&adapter->afu_list_lock); |
| |
| err: |
| /* All the bits that happen in both error_detected and cxl_remove |
| * should be idempotent, so we don't need to worry about leaving a mix |
| * of unconfigured and reconfigured resources. |
| */ |
| dev_err(&pdev->dev, "EEH recovery failed. Asking to be disconnected.\n"); |
| return PCI_ERS_RESULT_DISCONNECT; |
| } |
| |
| static void cxl_pci_resume(struct pci_dev *pdev) |
| { |
| struct cxl *adapter = pci_get_drvdata(pdev); |
| struct cxl_afu *afu; |
| struct pci_dev *afu_dev; |
| struct pci_driver *afu_drv; |
| const struct pci_error_handlers *err_handler; |
| int i; |
| |
| /* Everything is back now. Drivers should restart work now. |
| * This is not the place to be checking if everything came back up |
| * properly, because there's no return value: do that in slot_reset. |
| */ |
| spin_lock(&adapter->afu_list_lock); |
| for (i = 0; i < adapter->slices; i++) { |
| afu = adapter->afu[i]; |
| |
| if (afu == NULL || afu->phb == NULL) |
| continue; |
| |
| list_for_each_entry(afu_dev, &afu->phb->bus->devices, bus_list) { |
| afu_drv = to_pci_driver(afu_dev->dev.driver); |
| if (!afu_drv) |
| continue; |
| |
| err_handler = afu_drv->err_handler; |
| if (err_handler && err_handler->resume) |
| err_handler->resume(afu_dev); |
| } |
| } |
| spin_unlock(&adapter->afu_list_lock); |
| } |
| |
| static const struct pci_error_handlers cxl_err_handler = { |
| .error_detected = cxl_pci_error_detected, |
| .slot_reset = cxl_pci_slot_reset, |
| .resume = cxl_pci_resume, |
| }; |
| |
| struct pci_driver cxl_pci_driver = { |
| .name = "cxl-pci", |
| .id_table = cxl_pci_tbl, |
| .probe = cxl_probe, |
| .remove = cxl_remove, |
| .shutdown = cxl_remove, |
| .err_handler = &cxl_err_handler, |
| }; |