| // SPDX-License-Identifier: GPL-2.0-only |
| /* |
| * Copyright (C) 2011 ST-Ericsson SA. |
| * Copyright (C) 2009 Motorola, Inc. |
| * |
| * Simple driver for National Semiconductor LM3530 Backlight driver chip |
| * |
| * Author: Shreshtha Kumar SAHU <shreshthakumar.sahu@stericsson.com> |
| * based on leds-lm3530.c by Dan Murphy <D.Murphy@motorola.com> |
| */ |
| |
| #include <linux/i2c.h> |
| #include <linux/leds.h> |
| #include <linux/slab.h> |
| #include <linux/platform_device.h> |
| #include <linux/input.h> |
| #include <linux/led-lm3530.h> |
| #include <linux/types.h> |
| #include <linux/regulator/consumer.h> |
| #include <linux/module.h> |
| |
| #define LM3530_LED_DEV "lcd-backlight" |
| #define LM3530_NAME "lm3530-led" |
| |
| #define LM3530_GEN_CONFIG 0x10 |
| #define LM3530_ALS_CONFIG 0x20 |
| #define LM3530_BRT_RAMP_RATE 0x30 |
| #define LM3530_ALS_IMP_SELECT 0x41 |
| #define LM3530_BRT_CTRL_REG 0xA0 |
| #define LM3530_ALS_ZB0_REG 0x60 |
| #define LM3530_ALS_ZB1_REG 0x61 |
| #define LM3530_ALS_ZB2_REG 0x62 |
| #define LM3530_ALS_ZB3_REG 0x63 |
| #define LM3530_ALS_Z0T_REG 0x70 |
| #define LM3530_ALS_Z1T_REG 0x71 |
| #define LM3530_ALS_Z2T_REG 0x72 |
| #define LM3530_ALS_Z3T_REG 0x73 |
| #define LM3530_ALS_Z4T_REG 0x74 |
| #define LM3530_REG_MAX 14 |
| |
| /* General Control Register */ |
| #define LM3530_EN_I2C_SHIFT (0) |
| #define LM3530_RAMP_LAW_SHIFT (1) |
| #define LM3530_MAX_CURR_SHIFT (2) |
| #define LM3530_EN_PWM_SHIFT (5) |
| #define LM3530_PWM_POL_SHIFT (6) |
| #define LM3530_EN_PWM_SIMPLE_SHIFT (7) |
| |
| #define LM3530_ENABLE_I2C (1 << LM3530_EN_I2C_SHIFT) |
| #define LM3530_ENABLE_PWM (1 << LM3530_EN_PWM_SHIFT) |
| #define LM3530_POL_LOW (1 << LM3530_PWM_POL_SHIFT) |
| #define LM3530_ENABLE_PWM_SIMPLE (1 << LM3530_EN_PWM_SIMPLE_SHIFT) |
| |
| /* ALS Config Register Options */ |
| #define LM3530_ALS_AVG_TIME_SHIFT (0) |
| #define LM3530_EN_ALS_SHIFT (3) |
| #define LM3530_ALS_SEL_SHIFT (5) |
| |
| #define LM3530_ENABLE_ALS (3 << LM3530_EN_ALS_SHIFT) |
| |
| /* Brightness Ramp Rate Register */ |
| #define LM3530_BRT_RAMP_FALL_SHIFT (0) |
| #define LM3530_BRT_RAMP_RISE_SHIFT (3) |
| |
| /* ALS Resistor Select */ |
| #define LM3530_ALS1_IMP_SHIFT (0) |
| #define LM3530_ALS2_IMP_SHIFT (4) |
| |
| /* Zone Boundary Register defaults */ |
| #define LM3530_ALS_ZB_MAX (4) |
| #define LM3530_ALS_WINDOW_mV (1000) |
| #define LM3530_ALS_OFFSET_mV (4) |
| |
| /* Zone Target Register defaults */ |
| #define LM3530_DEF_ZT_0 (0x7F) |
| #define LM3530_DEF_ZT_1 (0x66) |
| #define LM3530_DEF_ZT_2 (0x4C) |
| #define LM3530_DEF_ZT_3 (0x33) |
| #define LM3530_DEF_ZT_4 (0x19) |
| |
| /* 7 bits are used for the brightness : LM3530_BRT_CTRL_REG */ |
| #define MAX_BRIGHTNESS (127) |
| |
| struct lm3530_mode_map { |
| const char *mode; |
| enum lm3530_mode mode_val; |
| }; |
| |
| static struct lm3530_mode_map mode_map[] = { |
| { "man", LM3530_BL_MODE_MANUAL }, |
| { "als", LM3530_BL_MODE_ALS }, |
| { "pwm", LM3530_BL_MODE_PWM }, |
| }; |
| |
| /** |
| * struct lm3530_data |
| * @led_dev: led class device |
| * @client: i2c client |
| * @pdata: LM3530 platform data |
| * @mode: mode of operation - manual, ALS, PWM |
| * @regulator: regulator |
| * @brightness: previous brightness value |
| * @enable: regulator is enabled |
| */ |
| struct lm3530_data { |
| struct led_classdev led_dev; |
| struct i2c_client *client; |
| struct lm3530_platform_data *pdata; |
| enum lm3530_mode mode; |
| struct regulator *regulator; |
| enum led_brightness brightness; |
| bool enable; |
| }; |
| |
| /* |
| * struct lm3530_als_data |
| * @config : value of ALS configuration register |
| * @imp_sel : value of ALS resistor select register |
| * @zone : values of ALS ZB(Zone Boundary) registers |
| */ |
| struct lm3530_als_data { |
| u8 config; |
| u8 imp_sel; |
| u8 zones[LM3530_ALS_ZB_MAX]; |
| }; |
| |
| static const u8 lm3530_reg[LM3530_REG_MAX] = { |
| LM3530_GEN_CONFIG, |
| LM3530_ALS_CONFIG, |
| LM3530_BRT_RAMP_RATE, |
| LM3530_ALS_IMP_SELECT, |
| LM3530_BRT_CTRL_REG, |
| LM3530_ALS_ZB0_REG, |
| LM3530_ALS_ZB1_REG, |
| LM3530_ALS_ZB2_REG, |
| LM3530_ALS_ZB3_REG, |
| LM3530_ALS_Z0T_REG, |
| LM3530_ALS_Z1T_REG, |
| LM3530_ALS_Z2T_REG, |
| LM3530_ALS_Z3T_REG, |
| LM3530_ALS_Z4T_REG, |
| }; |
| |
| static int lm3530_get_mode_from_str(const char *str) |
| { |
| int i; |
| |
| for (i = 0; i < ARRAY_SIZE(mode_map); i++) |
| if (sysfs_streq(str, mode_map[i].mode)) |
| return mode_map[i].mode_val; |
| |
| return -EINVAL; |
| } |
| |
| static void lm3530_als_configure(struct lm3530_platform_data *pdata, |
| struct lm3530_als_data *als) |
| { |
| int i; |
| u32 als_vmin, als_vmax, als_vstep; |
| |
| if (pdata->als_vmax == 0) { |
| pdata->als_vmin = 0; |
| pdata->als_vmax = LM3530_ALS_WINDOW_mV; |
| } |
| |
| als_vmin = pdata->als_vmin; |
| als_vmax = pdata->als_vmax; |
| |
| if ((als_vmax - als_vmin) > LM3530_ALS_WINDOW_mV) |
| pdata->als_vmax = als_vmax = als_vmin + LM3530_ALS_WINDOW_mV; |
| |
| /* n zone boundary makes n+1 zones */ |
| als_vstep = (als_vmax - als_vmin) / (LM3530_ALS_ZB_MAX + 1); |
| |
| for (i = 0; i < LM3530_ALS_ZB_MAX; i++) |
| als->zones[i] = (((als_vmin + LM3530_ALS_OFFSET_mV) + |
| als_vstep + (i * als_vstep)) * LED_FULL) / 1000; |
| |
| als->config = |
| (pdata->als_avrg_time << LM3530_ALS_AVG_TIME_SHIFT) | |
| (LM3530_ENABLE_ALS) | |
| (pdata->als_input_mode << LM3530_ALS_SEL_SHIFT); |
| |
| als->imp_sel = |
| (pdata->als1_resistor_sel << LM3530_ALS1_IMP_SHIFT) | |
| (pdata->als2_resistor_sel << LM3530_ALS2_IMP_SHIFT); |
| } |
| |
| static int lm3530_led_enable(struct lm3530_data *drvdata) |
| { |
| int ret; |
| |
| if (drvdata->enable) |
| return 0; |
| |
| ret = regulator_enable(drvdata->regulator); |
| if (ret) { |
| dev_err(drvdata->led_dev.dev, "Failed to enable vin:%d\n", ret); |
| return ret; |
| } |
| |
| drvdata->enable = true; |
| return 0; |
| } |
| |
| static void lm3530_led_disable(struct lm3530_data *drvdata) |
| { |
| int ret; |
| |
| if (!drvdata->enable) |
| return; |
| |
| ret = regulator_disable(drvdata->regulator); |
| if (ret) { |
| dev_err(drvdata->led_dev.dev, "Failed to disable vin:%d\n", |
| ret); |
| return; |
| } |
| |
| drvdata->enable = false; |
| } |
| |
| static int lm3530_init_registers(struct lm3530_data *drvdata) |
| { |
| int ret = 0; |
| int i; |
| u8 gen_config; |
| u8 brt_ramp; |
| u8 brightness; |
| u8 reg_val[LM3530_REG_MAX]; |
| struct lm3530_platform_data *pdata = drvdata->pdata; |
| struct i2c_client *client = drvdata->client; |
| struct lm3530_pwm_data *pwm = &pdata->pwm_data; |
| struct lm3530_als_data als; |
| |
| memset(&als, 0, sizeof(struct lm3530_als_data)); |
| |
| gen_config = (pdata->brt_ramp_law << LM3530_RAMP_LAW_SHIFT) | |
| ((pdata->max_current & 7) << LM3530_MAX_CURR_SHIFT); |
| |
| switch (drvdata->mode) { |
| case LM3530_BL_MODE_MANUAL: |
| gen_config |= LM3530_ENABLE_I2C; |
| break; |
| case LM3530_BL_MODE_ALS: |
| gen_config |= LM3530_ENABLE_I2C; |
| lm3530_als_configure(pdata, &als); |
| break; |
| case LM3530_BL_MODE_PWM: |
| gen_config |= LM3530_ENABLE_PWM | LM3530_ENABLE_PWM_SIMPLE | |
| (pdata->pwm_pol_hi << LM3530_PWM_POL_SHIFT); |
| break; |
| } |
| |
| brt_ramp = (pdata->brt_ramp_fall << LM3530_BRT_RAMP_FALL_SHIFT) | |
| (pdata->brt_ramp_rise << LM3530_BRT_RAMP_RISE_SHIFT); |
| |
| if (drvdata->brightness) |
| brightness = drvdata->brightness; |
| else |
| brightness = drvdata->brightness = pdata->brt_val; |
| |
| if (brightness > drvdata->led_dev.max_brightness) |
| brightness = drvdata->led_dev.max_brightness; |
| |
| reg_val[0] = gen_config; /* LM3530_GEN_CONFIG */ |
| reg_val[1] = als.config; /* LM3530_ALS_CONFIG */ |
| reg_val[2] = brt_ramp; /* LM3530_BRT_RAMP_RATE */ |
| reg_val[3] = als.imp_sel; /* LM3530_ALS_IMP_SELECT */ |
| reg_val[4] = brightness; /* LM3530_BRT_CTRL_REG */ |
| reg_val[5] = als.zones[0]; /* LM3530_ALS_ZB0_REG */ |
| reg_val[6] = als.zones[1]; /* LM3530_ALS_ZB1_REG */ |
| reg_val[7] = als.zones[2]; /* LM3530_ALS_ZB2_REG */ |
| reg_val[8] = als.zones[3]; /* LM3530_ALS_ZB3_REG */ |
| reg_val[9] = LM3530_DEF_ZT_0; /* LM3530_ALS_Z0T_REG */ |
| reg_val[10] = LM3530_DEF_ZT_1; /* LM3530_ALS_Z1T_REG */ |
| reg_val[11] = LM3530_DEF_ZT_2; /* LM3530_ALS_Z2T_REG */ |
| reg_val[12] = LM3530_DEF_ZT_3; /* LM3530_ALS_Z3T_REG */ |
| reg_val[13] = LM3530_DEF_ZT_4; /* LM3530_ALS_Z4T_REG */ |
| |
| ret = lm3530_led_enable(drvdata); |
| if (ret) |
| return ret; |
| |
| for (i = 0; i < LM3530_REG_MAX; i++) { |
| /* do not update brightness register when pwm mode */ |
| if (lm3530_reg[i] == LM3530_BRT_CTRL_REG && |
| drvdata->mode == LM3530_BL_MODE_PWM) { |
| if (pwm->pwm_set_intensity) |
| pwm->pwm_set_intensity(reg_val[i], |
| drvdata->led_dev.max_brightness); |
| continue; |
| } |
| |
| ret = i2c_smbus_write_byte_data(client, |
| lm3530_reg[i], reg_val[i]); |
| if (ret) |
| break; |
| } |
| |
| return ret; |
| } |
| |
| static void lm3530_brightness_set(struct led_classdev *led_cdev, |
| enum led_brightness brt_val) |
| { |
| int err; |
| struct lm3530_data *drvdata = |
| container_of(led_cdev, struct lm3530_data, led_dev); |
| struct lm3530_platform_data *pdata = drvdata->pdata; |
| struct lm3530_pwm_data *pwm = &pdata->pwm_data; |
| u8 max_brightness = led_cdev->max_brightness; |
| |
| switch (drvdata->mode) { |
| case LM3530_BL_MODE_MANUAL: |
| |
| if (!drvdata->enable) { |
| err = lm3530_init_registers(drvdata); |
| if (err) { |
| dev_err(&drvdata->client->dev, |
| "Register Init failed: %d\n", err); |
| break; |
| } |
| } |
| |
| /* set the brightness in brightness control register*/ |
| err = i2c_smbus_write_byte_data(drvdata->client, |
| LM3530_BRT_CTRL_REG, brt_val); |
| if (err) |
| dev_err(&drvdata->client->dev, |
| "Unable to set brightness: %d\n", err); |
| else |
| drvdata->brightness = brt_val; |
| |
| if (brt_val == 0) |
| lm3530_led_disable(drvdata); |
| break; |
| case LM3530_BL_MODE_ALS: |
| break; |
| case LM3530_BL_MODE_PWM: |
| if (pwm->pwm_set_intensity) |
| pwm->pwm_set_intensity(brt_val, max_brightness); |
| break; |
| default: |
| break; |
| } |
| } |
| |
| static ssize_t mode_show(struct device *dev, |
| struct device_attribute *attr, char *buf) |
| { |
| struct led_classdev *led_cdev = dev_get_drvdata(dev); |
| struct lm3530_data *drvdata; |
| int i, len = 0; |
| |
| drvdata = container_of(led_cdev, struct lm3530_data, led_dev); |
| for (i = 0; i < ARRAY_SIZE(mode_map); i++) |
| if (drvdata->mode == mode_map[i].mode_val) |
| len += sprintf(buf + len, "[%s] ", mode_map[i].mode); |
| else |
| len += sprintf(buf + len, "%s ", mode_map[i].mode); |
| |
| len += sprintf(buf + len, "\n"); |
| |
| return len; |
| } |
| |
| static ssize_t mode_store(struct device *dev, struct device_attribute |
| *attr, const char *buf, size_t size) |
| { |
| struct led_classdev *led_cdev = dev_get_drvdata(dev); |
| struct lm3530_data *drvdata; |
| struct lm3530_pwm_data *pwm; |
| u8 max_brightness; |
| int mode, err; |
| |
| drvdata = container_of(led_cdev, struct lm3530_data, led_dev); |
| pwm = &drvdata->pdata->pwm_data; |
| max_brightness = led_cdev->max_brightness; |
| mode = lm3530_get_mode_from_str(buf); |
| if (mode < 0) { |
| dev_err(dev, "Invalid mode\n"); |
| return mode; |
| } |
| |
| drvdata->mode = mode; |
| |
| /* set pwm to low if unnecessary */ |
| if (mode != LM3530_BL_MODE_PWM && pwm->pwm_set_intensity) |
| pwm->pwm_set_intensity(0, max_brightness); |
| |
| err = lm3530_init_registers(drvdata); |
| if (err) { |
| dev_err(dev, "Setting %s Mode failed :%d\n", buf, err); |
| return err; |
| } |
| |
| return sizeof(drvdata->mode); |
| } |
| static DEVICE_ATTR_RW(mode); |
| |
| static struct attribute *lm3530_attrs[] = { |
| &dev_attr_mode.attr, |
| NULL |
| }; |
| ATTRIBUTE_GROUPS(lm3530); |
| |
| static int lm3530_probe(struct i2c_client *client) |
| { |
| struct lm3530_platform_data *pdata = dev_get_platdata(&client->dev); |
| struct lm3530_data *drvdata; |
| int err = 0; |
| |
| if (pdata == NULL) { |
| dev_err(&client->dev, "platform data required\n"); |
| return -ENODEV; |
| } |
| |
| /* BL mode */ |
| if (pdata->mode > LM3530_BL_MODE_PWM) { |
| dev_err(&client->dev, "Illegal Mode request\n"); |
| return -EINVAL; |
| } |
| |
| if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) { |
| dev_err(&client->dev, "I2C_FUNC_I2C not supported\n"); |
| return -EIO; |
| } |
| |
| drvdata = devm_kzalloc(&client->dev, sizeof(struct lm3530_data), |
| GFP_KERNEL); |
| if (drvdata == NULL) |
| return -ENOMEM; |
| |
| drvdata->mode = pdata->mode; |
| drvdata->client = client; |
| drvdata->pdata = pdata; |
| drvdata->brightness = LED_OFF; |
| drvdata->enable = false; |
| drvdata->led_dev.name = LM3530_LED_DEV; |
| drvdata->led_dev.brightness_set = lm3530_brightness_set; |
| drvdata->led_dev.max_brightness = MAX_BRIGHTNESS; |
| drvdata->led_dev.groups = lm3530_groups; |
| |
| i2c_set_clientdata(client, drvdata); |
| |
| drvdata->regulator = devm_regulator_get(&client->dev, "vin"); |
| if (IS_ERR(drvdata->regulator)) { |
| dev_err(&client->dev, "regulator get failed\n"); |
| err = PTR_ERR(drvdata->regulator); |
| drvdata->regulator = NULL; |
| return err; |
| } |
| |
| if (drvdata->pdata->brt_val) { |
| err = lm3530_init_registers(drvdata); |
| if (err < 0) { |
| dev_err(&client->dev, |
| "Register Init failed: %d\n", err); |
| return err; |
| } |
| } |
| err = led_classdev_register(&client->dev, &drvdata->led_dev); |
| if (err < 0) { |
| dev_err(&client->dev, "Register led class failed: %d\n", err); |
| return err; |
| } |
| |
| return 0; |
| } |
| |
| static void lm3530_remove(struct i2c_client *client) |
| { |
| struct lm3530_data *drvdata = i2c_get_clientdata(client); |
| |
| lm3530_led_disable(drvdata); |
| led_classdev_unregister(&drvdata->led_dev); |
| } |
| |
| static const struct i2c_device_id lm3530_id[] = { |
| { LM3530_NAME }, |
| {} |
| }; |
| MODULE_DEVICE_TABLE(i2c, lm3530_id); |
| |
| static struct i2c_driver lm3530_i2c_driver = { |
| .probe = lm3530_probe, |
| .remove = lm3530_remove, |
| .id_table = lm3530_id, |
| .driver = { |
| .name = LM3530_NAME, |
| }, |
| }; |
| |
| module_i2c_driver(lm3530_i2c_driver); |
| |
| MODULE_DESCRIPTION("Back Light driver for LM3530"); |
| MODULE_LICENSE("GPL v2"); |
| MODULE_AUTHOR("Shreshtha Kumar SAHU <shreshthakumar.sahu@stericsson.com>"); |