| /* SPDX-License-Identifier: GPL-2.0 */ |
| |
| #ifndef __ASM_ARC_ENTRY_ARCV2_H |
| #define __ASM_ARC_ENTRY_ARCV2_H |
| |
| #include <asm/asm-offsets.h> |
| #include <asm/dsp-impl.h> |
| #include <asm/irqflags-arcv2.h> |
| #include <asm/thread_info.h> /* For THREAD_SIZE */ |
| |
| /* |
| * Interrupt/Exception stack layout (pt_regs) for ARCv2 |
| * (End of struct aligned to end of page [unless nested]) |
| * |
| * INTERRUPT EXCEPTION |
| * |
| * manual --------------------- manual |
| * | orig_r0 | |
| * | event/ECR | |
| * | bta | |
| * | user_r25 | |
| * | gp | |
| * | fp | |
| * | sp | |
| * | r12 | |
| * | r30 | |
| * | r58 | |
| * | r59 | |
| * hw autosave --------------------- |
| * optional | r0 | |
| * | r1 | |
| * ~ ~ |
| * | r9 | |
| * | r10 | |
| * | r11 | |
| * | blink | |
| * | lpe | |
| * | lps | |
| * | lpc | |
| * | ei base | |
| * | ldi base | |
| * | jli base | |
| * --------------------- |
| * hw autosave | pc / eret | |
| * mandatory | stat32 / erstatus | |
| * --------------------- |
| */ |
| |
| /*------------------------------------------------------------------------*/ |
| .macro INTERRUPT_PROLOGUE |
| |
| ; (A) Before jumping to Interrupt Vector, hardware micro-ops did following: |
| ; 1. SP auto-switched to kernel mode stack |
| ; 2. STATUS32.Z flag set if in U mode at time of interrupt (U:1,K:0) |
| ; 3. Auto save: (mandatory) Push PC and STAT32 on stack |
| ; hardware does even if CONFIG_ARC_IRQ_NO_AUTOSAVE |
| ; 4. Auto save: (optional) r0-r11, blink, LPE,LPS,LPC, JLI,LDI,EI |
| ; |
| ; (B) Manually saved some regs: r12,r25,r30, sp,fp,gp, ACCL pair |
| |
| #ifdef CONFIG_ARC_IRQ_NO_AUTOSAVE |
| ; carve pt_regs on stack (case #3), PC/STAT32 already on stack |
| sub sp, sp, SZ_PT_REGS - 8 |
| |
| __SAVE_REGFILE_HARD |
| #else |
| ; carve pt_regs on stack (case #4), which grew partially already |
| sub sp, sp, PT_r0 |
| #endif |
| |
| __SAVE_REGFILE_SOFT |
| .endm |
| |
| /*------------------------------------------------------------------------*/ |
| .macro EXCEPTION_PROLOGUE |
| |
| ; (A) Before jumping to Exception Vector, hardware micro-ops did following: |
| ; 1. SP auto-switched to kernel mode stack |
| ; 2. STATUS32.Z flag set if in U mode at time of exception (U:1,K:0) |
| ; |
| ; (B) Manually save the complete reg file below |
| |
| sub sp, sp, SZ_PT_REGS ; carve pt_regs |
| |
| ; _HARD saves r10 clobbered by _SOFT as scratch hence comes first |
| |
| __SAVE_REGFILE_HARD |
| __SAVE_REGFILE_SOFT |
| |
| st r0, [sp] ; orig_r0 |
| |
| lr r10, [eret] |
| lr r11, [erstatus] |
| ST2 r10, r11, PT_ret |
| |
| lr r10, [ecr] |
| lr r11, [erbta] |
| ST2 r10, r11, PT_event |
| |
| ; OUTPUT: r10 has ECR expected by EV_Trap |
| .endm |
| |
| /*------------------------------------------------------------------------ |
| * This macro saves the registers manually which would normally be autosaved |
| * by hardware on taken interrupts. It is used by |
| * - exception handlers (which don't have autosave) |
| * - interrupt autosave disabled due to CONFIG_ARC_IRQ_NO_AUTOSAVE |
| */ |
| .macro __SAVE_REGFILE_HARD |
| |
| ST2 r0, r1, PT_r0 |
| ST2 r2, r3, PT_r2 |
| ST2 r4, r5, PT_r4 |
| ST2 r6, r7, PT_r6 |
| ST2 r8, r9, PT_r8 |
| ST2 r10, r11, PT_r10 |
| |
| st blink, [sp, PT_blink] |
| |
| lr r10, [lp_end] |
| lr r11, [lp_start] |
| ST2 r10, r11, PT_lpe |
| |
| st lp_count, [sp, PT_lpc] |
| |
| ; skip JLI, LDI, EI for now |
| .endm |
| |
| /*------------------------------------------------------------------------ |
| * This macros saves a bunch of other registers which can't be autosaved for |
| * various reasons: |
| * - r12: the last caller saved scratch reg since hardware saves in pairs so r0-r11 |
| * - r30: free reg, used by gcc as scratch |
| * - ACCL/ACCH pair when they exist |
| */ |
| .macro __SAVE_REGFILE_SOFT |
| |
| ST2 gp, fp, PT_r26 ; gp (r26), fp (r27) |
| |
| st r12, [sp, PT_sp + 4] |
| st r30, [sp, PT_sp + 8] |
| |
| ; Saving pt_regs->sp correctly requires some extra work due to the way |
| ; Auto stack switch works |
| ; - U mode: retrieve it from AUX_USER_SP |
| ; - K mode: add the offset from current SP where H/w starts auto push |
| ; |
| ; 1. Utilize the fact that Z bit is set if Intr taken in U mode |
| ; 2. Upon entry SP is always saved (for any inspection, unwinding etc), |
| ; but on return, restored only if U mode |
| |
| lr r10, [AUX_USER_SP] ; U mode SP |
| |
| ; ISA requires ADD.nz to have same dest and src reg operands |
| mov.nz r10, sp |
| add.nz r10, r10, SZ_PT_REGS ; K mode SP |
| |
| st r10, [sp, PT_sp] ; SP (pt_regs->sp) |
| |
| #ifdef CONFIG_ARC_CURR_IN_REG |
| st r25, [sp, PT_user_r25] |
| GET_CURR_TASK_ON_CPU r25 |
| #endif |
| |
| #ifdef CONFIG_ARC_HAS_ACCL_REGS |
| ST2 r58, r59, PT_r58 |
| #endif |
| |
| /* clobbers r10, r11 registers pair */ |
| DSP_SAVE_REGFILE_IRQ |
| .endm |
| |
| /*------------------------------------------------------------------------*/ |
| .macro __RESTORE_REGFILE_SOFT |
| |
| LD2 gp, fp, PT_r26 ; gp (r26), fp (r27) |
| |
| ld r12, [sp, PT_r12] |
| ld r30, [sp, PT_r30] |
| |
| ; Restore SP (into AUX_USER_SP) only if returning to U mode |
| ; - for K mode, it will be implicitly restored as stack is unwound |
| ; - Z flag set on K is inverse of what hardware does on interrupt entry |
| ; but that doesn't really matter |
| bz 1f |
| |
| ld r10, [sp, PT_sp] ; SP (pt_regs->sp) |
| sr r10, [AUX_USER_SP] |
| 1: |
| |
| #ifdef CONFIG_ARC_CURR_IN_REG |
| ld r25, [sp, PT_user_r25] |
| #endif |
| |
| /* clobbers r10, r11 registers pair */ |
| DSP_RESTORE_REGFILE_IRQ |
| |
| #ifdef CONFIG_ARC_HAS_ACCL_REGS |
| LD2 r58, r59, PT_r58 |
| #endif |
| .endm |
| |
| /*------------------------------------------------------------------------*/ |
| .macro __RESTORE_REGFILE_HARD |
| |
| ld blink, [sp, PT_blink] |
| |
| LD2 r10, r11, PT_lpe |
| sr r10, [lp_end] |
| sr r11, [lp_start] |
| |
| ld r10, [sp, PT_lpc] ; lp_count can't be target of LD |
| mov lp_count, r10 |
| |
| LD2 r0, r1, PT_r0 |
| LD2 r2, r3, PT_r2 |
| LD2 r4, r5, PT_r4 |
| LD2 r6, r7, PT_r6 |
| LD2 r8, r9, PT_r8 |
| LD2 r10, r11, PT_r10 |
| .endm |
| |
| |
| /*------------------------------------------------------------------------*/ |
| .macro INTERRUPT_EPILOGUE |
| |
| ; INPUT: r0 has STAT32 of calling context |
| ; INPUT: Z flag set if returning to K mode |
| |
| ; _SOFT clobbers r10 restored by _HARD hence the order |
| |
| __RESTORE_REGFILE_SOFT |
| |
| #ifdef CONFIG_ARC_IRQ_NO_AUTOSAVE |
| __RESTORE_REGFILE_HARD |
| |
| ; SP points to PC/STAT32: hw restores them despite NO_AUTOSAVE |
| add sp, sp, SZ_PT_REGS - 8 |
| #else |
| add sp, sp, PT_r0 |
| #endif |
| |
| .endm |
| |
| /*------------------------------------------------------------------------*/ |
| .macro EXCEPTION_EPILOGUE |
| |
| ; INPUT: r0 has STAT32 of calling context |
| |
| btst r0, STATUS_U_BIT ; Z flag set if K, used in restoring SP |
| |
| ld r10, [sp, PT_event + 4] |
| sr r10, [erbta] |
| |
| LD2 r10, r11, PT_ret |
| sr r10, [eret] |
| sr r11, [erstatus] |
| |
| __RESTORE_REGFILE_SOFT |
| __RESTORE_REGFILE_HARD |
| |
| add sp, sp, SZ_PT_REGS |
| .endm |
| |
| .macro FAKE_RET_FROM_EXCPN |
| lr r9, [status32] |
| bic r9, r9, STATUS_AE_MASK |
| or r9, r9, STATUS_IE_MASK |
| kflag r9 |
| .endm |
| |
| /* Get thread_info of "current" tsk */ |
| .macro GET_CURR_THR_INFO_FROM_SP reg |
| bmskn \reg, sp, THREAD_SHIFT - 1 |
| .endm |
| |
| /* Get CPU-ID of this core */ |
| .macro GET_CPU_ID reg |
| lr \reg, [identity] |
| xbfu \reg, \reg, 0xE8 /* 00111 01000 */ |
| /* M = 8-1 N = 8 */ |
| .endm |
| |
| #endif |
