| // SPDX-License-Identifier: GPL-2.0 |
| /* Copyright (c) 2022 Baylibre, SAS. |
| * Author: Jerome Brunet <jbrunet@baylibre.com> |
| */ |
| |
| #include <linux/bitfield.h> |
| #include <linux/delay.h> |
| #include <linux/clk.h> |
| #include <linux/io.h> |
| #include <linux/mdio-mux.h> |
| #include <linux/module.h> |
| #include <linux/platform_device.h> |
| |
| #define ETH_REG2 0x0 |
| #define REG2_PHYID GENMASK(21, 0) |
| #define EPHY_GXL_ID 0x110181 |
| #define REG2_LEDACT GENMASK(23, 22) |
| #define REG2_LEDLINK GENMASK(25, 24) |
| #define REG2_DIV4SEL BIT(27) |
| #define REG2_ADCBYPASS BIT(30) |
| #define REG2_CLKINSEL BIT(31) |
| #define ETH_REG3 0x4 |
| #define REG3_ENH BIT(3) |
| #define REG3_CFGMODE GENMASK(6, 4) |
| #define REG3_AUTOMDIX BIT(7) |
| #define REG3_PHYADDR GENMASK(12, 8) |
| #define REG3_PWRUPRST BIT(21) |
| #define REG3_PWRDOWN BIT(22) |
| #define REG3_LEDPOL BIT(23) |
| #define REG3_PHYMDI BIT(26) |
| #define REG3_CLKINEN BIT(29) |
| #define REG3_PHYIP BIT(30) |
| #define REG3_PHYEN BIT(31) |
| #define ETH_REG4 0x8 |
| #define REG4_PWRUPRSTSIG BIT(0) |
| |
| #define MESON_GXL_MDIO_EXTERNAL_ID 0 |
| #define MESON_GXL_MDIO_INTERNAL_ID 1 |
| |
| struct gxl_mdio_mux { |
| void __iomem *regs; |
| void *mux_handle; |
| }; |
| |
| static void gxl_enable_internal_mdio(struct gxl_mdio_mux *priv) |
| { |
| u32 val; |
| |
| /* Setup the internal phy */ |
| val = (REG3_ENH | |
| FIELD_PREP(REG3_CFGMODE, 0x7) | |
| REG3_AUTOMDIX | |
| FIELD_PREP(REG3_PHYADDR, 8) | |
| REG3_LEDPOL | |
| REG3_PHYMDI | |
| REG3_CLKINEN | |
| REG3_PHYIP); |
| |
| writel(REG4_PWRUPRSTSIG, priv->regs + ETH_REG4); |
| writel(val, priv->regs + ETH_REG3); |
| mdelay(10); |
| |
| /* NOTE: The HW kept the phy id configurable at runtime. |
| * The id below is arbitrary. It is the one used in the vendor code. |
| * The only constraint is that it must match the one in |
| * drivers/net/phy/meson-gxl.c to properly match the PHY. |
| */ |
| writel(FIELD_PREP(REG2_PHYID, EPHY_GXL_ID), |
| priv->regs + ETH_REG2); |
| |
| /* Enable the internal phy */ |
| val |= REG3_PHYEN; |
| writel(val, priv->regs + ETH_REG3); |
| writel(0, priv->regs + ETH_REG4); |
| |
| /* The phy needs a bit of time to power up */ |
| mdelay(10); |
| } |
| |
| static void gxl_enable_external_mdio(struct gxl_mdio_mux *priv) |
| { |
| /* Reset the mdio bus mux to the external phy */ |
| writel(0, priv->regs + ETH_REG3); |
| } |
| |
| static int gxl_mdio_switch_fn(int current_child, int desired_child, |
| void *data) |
| { |
| struct gxl_mdio_mux *priv = dev_get_drvdata(data); |
| |
| if (current_child == desired_child) |
| return 0; |
| |
| switch (desired_child) { |
| case MESON_GXL_MDIO_EXTERNAL_ID: |
| gxl_enable_external_mdio(priv); |
| break; |
| case MESON_GXL_MDIO_INTERNAL_ID: |
| gxl_enable_internal_mdio(priv); |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| return 0; |
| } |
| |
| static const struct of_device_id gxl_mdio_mux_match[] = { |
| { .compatible = "amlogic,gxl-mdio-mux", }, |
| {}, |
| }; |
| MODULE_DEVICE_TABLE(of, gxl_mdio_mux_match); |
| |
| static int gxl_mdio_mux_probe(struct platform_device *pdev) |
| { |
| struct device *dev = &pdev->dev; |
| struct gxl_mdio_mux *priv; |
| struct clk *rclk; |
| int ret; |
| |
| priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); |
| if (!priv) |
| return -ENOMEM; |
| platform_set_drvdata(pdev, priv); |
| |
| priv->regs = devm_platform_ioremap_resource(pdev, 0); |
| if (IS_ERR(priv->regs)) |
| return PTR_ERR(priv->regs); |
| |
| rclk = devm_clk_get_enabled(dev, "ref"); |
| if (IS_ERR(rclk)) |
| return dev_err_probe(dev, PTR_ERR(rclk), |
| "failed to get reference clock\n"); |
| |
| ret = mdio_mux_init(dev, dev->of_node, gxl_mdio_switch_fn, |
| &priv->mux_handle, dev, NULL); |
| if (ret) |
| dev_err_probe(dev, ret, "mdio multiplexer init failed\n"); |
| |
| return ret; |
| } |
| |
| static void gxl_mdio_mux_remove(struct platform_device *pdev) |
| { |
| struct gxl_mdio_mux *priv = platform_get_drvdata(pdev); |
| |
| mdio_mux_uninit(priv->mux_handle); |
| } |
| |
| static struct platform_driver gxl_mdio_mux_driver = { |
| .probe = gxl_mdio_mux_probe, |
| .remove_new = gxl_mdio_mux_remove, |
| .driver = { |
| .name = "gxl-mdio-mux", |
| .of_match_table = gxl_mdio_mux_match, |
| }, |
| }; |
| module_platform_driver(gxl_mdio_mux_driver); |
| |
| MODULE_DESCRIPTION("Amlogic GXL MDIO multiplexer driver"); |
| MODULE_AUTHOR("Jerome Brunet <jbrunet@baylibre.com>"); |
| MODULE_LICENSE("GPL"); |