blob: 07550e775e8047111e2f280ef8d94da993970ebb [file] [log] [blame]
/*
* Device Tree Source for the Koelsch board
*
* Copyright (C) 2013 Renesas Electronics Corporation
* Copyright (C) 2013-2014 Renesas Solutions Corp.
* Copyright (C) 2014 Cogent Embedded, Inc.
*
* This file is licensed under the terms of the GNU General Public License
* version 2. This program is licensed "as is" without any warranty of any
* kind, whether express or implied.
*/
/dts-v1/;
#include "r8a7791.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
model = "Koelsch";
compatible = "renesas,koelsch", "renesas,r8a7791";
aliases {
serial6 = &scif0;
serial7 = &scif1;
};
chosen {
bootargs = "console=ttySC6,115200 ignore_loglevel rw root=/dev/nfs ip=dhcp";
};
memory@40000000 {
device_type = "memory";
reg = <0 0x40000000 0 0x40000000>;
};
memory@200000000 {
device_type = "memory";
reg = <2 0x00000000 0 0x40000000>;
};
lbsc {
#address-cells = <1>;
#size-cells = <1>;
};
gpio-keys {
compatible = "gpio-keys";
key-1 {
gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
linux,code = <KEY_1>;
label = "SW2-1";
gpio-key,wakeup;
debounce-interval = <20>;
};
key-2 {
gpios = <&gpio5 1 GPIO_ACTIVE_LOW>;
linux,code = <KEY_2>;
label = "SW2-2";
gpio-key,wakeup;
debounce-interval = <20>;
};
key-3 {
gpios = <&gpio5 2 GPIO_ACTIVE_LOW>;
linux,code = <KEY_3>;
label = "SW2-3";
gpio-key,wakeup;
debounce-interval = <20>;
};
key-4 {
gpios = <&gpio5 3 GPIO_ACTIVE_LOW>;
linux,code = <KEY_4>;
label = "SW2-4";
gpio-key,wakeup;
debounce-interval = <20>;
};
key-a {
gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
linux,code = <KEY_A>;
label = "SW30";
gpio-key,wakeup;
debounce-interval = <20>;
};
key-b {
gpios = <&gpio7 1 GPIO_ACTIVE_LOW>;
linux,code = <KEY_B>;
label = "SW31";
gpio-key,wakeup;
debounce-interval = <20>;
};
key-c {
gpios = <&gpio7 2 GPIO_ACTIVE_LOW>;
linux,code = <KEY_C>;
label = "SW32";
gpio-key,wakeup;
debounce-interval = <20>;
};
key-d {
gpios = <&gpio7 3 GPIO_ACTIVE_LOW>;
linux,code = <KEY_D>;
label = "SW33";
gpio-key,wakeup;
debounce-interval = <20>;
};
key-e {
gpios = <&gpio7 4 GPIO_ACTIVE_LOW>;
linux,code = <KEY_E>;
label = "SW34";
gpio-key,wakeup;
debounce-interval = <20>;
};
key-f {
gpios = <&gpio7 5 GPIO_ACTIVE_LOW>;
linux,code = <KEY_F>;
label = "SW35";
gpio-key,wakeup;
debounce-interval = <20>;
};
key-g {
gpios = <&gpio7 6 GPIO_ACTIVE_LOW>;
linux,code = <KEY_G>;
label = "SW36";
gpio-key,wakeup;
debounce-interval = <20>;
};
};
leds {
compatible = "gpio-leds";
led6 {
gpios = <&gpio2 19 GPIO_ACTIVE_HIGH>;
};
led7 {
gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>;
};
led8 {
gpios = <&gpio2 21 GPIO_ACTIVE_HIGH>;
};
};
vcc_sdhi0: regulator@0 {
compatible = "regulator-fixed";
regulator-name = "SDHI0 Vcc";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&gpio7 17 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
vccq_sdhi0: regulator@1 {
compatible = "regulator-gpio";
regulator-name = "SDHI0 VccQ";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
gpios = <&gpio2 12 GPIO_ACTIVE_HIGH>;
gpios-states = <1>;
states = <3300000 1
1800000 0>;
};
vcc_sdhi1: regulator@2 {
compatible = "regulator-fixed";
regulator-name = "SDHI1 Vcc";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&gpio7 18 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
vccq_sdhi1: regulator@3 {
compatible = "regulator-gpio";
regulator-name = "SDHI1 VccQ";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
gpios = <&gpio2 13 GPIO_ACTIVE_HIGH>;
gpios-states = <1>;
states = <3300000 1
1800000 0>;
};
vcc_sdhi2: regulator@4 {
compatible = "regulator-fixed";
regulator-name = "SDHI2 Vcc";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&gpio7 19 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
vccq_sdhi2: regulator@5 {
compatible = "regulator-gpio";
regulator-name = "SDHI2 VccQ";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>;
gpios-states = <1>;
states = <3300000 1
1800000 0>;
};
};
&extal_clk {
clock-frequency = <20000000>;
};
&pfc {
pinctrl-0 = <&du_pins>;
pinctrl-names = "default";
i2c2_pins: i2c2 {
renesas,groups = "i2c2";
renesas,function = "i2c2";
};
du_pins: du {
renesas,groups = "du_rgb666", "du_sync", "du_clk_out_0";
renesas,function = "du";
};
scif0_pins: serial0 {
renesas,groups = "scif0_data_d";
renesas,function = "scif0";
};
scif1_pins: serial1 {
renesas,groups = "scif1_data_d";
renesas,function = "scif1";
};
ether_pins: ether {
renesas,groups = "eth_link", "eth_mdio", "eth_rmii";
renesas,function = "eth";
};
phy1_pins: phy1 {
renesas,groups = "intc_irq0";
renesas,function = "intc";
};
sdhi0_pins: sd0 {
renesas,groups = "sdhi0_data4", "sdhi0_ctrl";
renesas,function = "sdhi0";
};
sdhi1_pins: sd1 {
renesas,groups = "sdhi1_data4", "sdhi1_ctrl";
renesas,function = "sdhi1";
};
sdhi2_pins: sd2 {
renesas,groups = "sdhi2_data4", "sdhi2_ctrl";
renesas,function = "sdhi2";
};
qspi_pins: spi0 {
renesas,groups = "qspi_ctrl", "qspi_data4";
renesas,function = "qspi";
};
msiof0_pins: spi1 {
renesas,groups = "msiof0_clk", "msiof0_sync", "msiof0_rx",
"msiof0_tx";
renesas,function = "msiof0";
};
usb0_pins: usb0 {
renesas,groups = "usb0";
renesas,function = "usb0";
};
usb1_pins: usb1 {
renesas,groups = "usb1";
renesas,function = "usb1";
};
vin1_pins: vin1 {
renesas,groups = "vin1_data8", "vin1_clk";
renesas,function = "vin1";
};
};
&ether {
pinctrl-0 = <&ether_pins &phy1_pins>;
pinctrl-names = "default";
phy-handle = <&phy1>;
renesas,ether-link-active-low;
status = "ok";
phy1: ethernet-phy@1 {
reg = <1>;
interrupt-parent = <&irqc0>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
micrel,led-mode = <1>;
};
};
&cmt0 {
status = "ok";
};
&sata0 {
status = "okay";
};
&scif0 {
pinctrl-0 = <&scif0_pins>;
pinctrl-names = "default";
status = "okay";
};
&scif1 {
pinctrl-0 = <&scif1_pins>;
pinctrl-names = "default";
status = "okay";
};
&sdhi0 {
pinctrl-0 = <&sdhi0_pins>;
pinctrl-names = "default";
vmmc-supply = <&vcc_sdhi0>;
vqmmc-supply = <&vccq_sdhi0>;
cd-gpios = <&gpio6 6 GPIO_ACTIVE_LOW>;
wp-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
status = "okay";
};
&sdhi1 {
pinctrl-0 = <&sdhi1_pins>;
pinctrl-names = "default";
vmmc-supply = <&vcc_sdhi1>;
vqmmc-supply = <&vccq_sdhi1>;
cd-gpios = <&gpio6 14 GPIO_ACTIVE_LOW>;
wp-gpios = <&gpio6 15 GPIO_ACTIVE_HIGH>;
status = "okay";
};
&sdhi2 {
pinctrl-0 = <&sdhi2_pins>;
pinctrl-names = "default";
vmmc-supply = <&vcc_sdhi2>;
vqmmc-supply = <&vccq_sdhi2>;
cd-gpios = <&gpio6 22 GPIO_ACTIVE_LOW>;
status = "okay";
};
&qspi {
pinctrl-0 = <&qspi_pins>;
pinctrl-names = "default";
status = "okay";
flash: flash@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "spansion,s25fl512s";
reg = <0>;
spi-max-frequency = <30000000>;
spi-tx-bus-width = <4>;
spi-rx-bus-width = <4>;
m25p,fast-read;
partition@0 {
label = "loader";
reg = <0x00000000 0x00080000>;
read-only;
};
partition@80000 {
label = "bootenv";
reg = <0x00080000 0x00080000>;
read-only;
};
partition@100000 {
label = "data";
reg = <0x00100000 0x03f00000>;
};
};
};
&msiof0 {
pinctrl-0 = <&msiof0_pins>;
pinctrl-names = "default";
status = "okay";
pmic: pmic@0 {
compatible = "renesas,r2a11302ft";
reg = <0>;
spi-max-frequency = <6000000>;
spi-cpol;
spi-cpha;
};
};
&i2c2 {
pinctrl-0 = <&i2c2_pins>;
pinctrl-names = "default";
status = "okay";
clock-frequency = <400000>;
composite-in@20 {
compatible = "adi,adv7180";
reg = <0x20>;
remote = <&vin1>;
port {
adv7180: endpoint {
bus-width = <8>;
remote-endpoint = <&vin1ep>;
};
};
};
eeprom@50 {
compatible = "renesas,24c02";
reg = <0x50>;
pagesize = <16>;
};
};
&i2c6 {
status = "okay";
clock-frequency = <100000>;
vdd_dvfs: regulator@68 {
compatible = "dlg,da9210";
reg = <0x68>;
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;
regulator-boot-on;
regulator-always-on;
};
};
&pci0 {
status = "okay";
pinctrl-0 = <&usb0_pins>;
pinctrl-names = "default";
};
&pci1 {
status = "okay";
pinctrl-0 = <&usb1_pins>;
pinctrl-names = "default";
};
&pcie_bus_clk {
status = "okay";
};
&pciec {
status = "okay";
};
&cpu0 {
cpu0-supply = <&vdd_dvfs>;
};
/* composite video input */
&vin1 {
status = "ok";
pinctrl-0 = <&vin1_pins>;
pinctrl-names = "default";
port {
#address-cells = <1>;
#size-cells = <0>;
vin1ep: endpoint {
remote-endpoint = <&adv7180>;
bus-width = <8>;
};
};
};