drivers/mmc/host/sdhci-of-esdhc.c

// SPDX-License-Identifier: GPL-2.0-or-later
/*
 * Freescale eSDHC controller driver.
 *
 * Copyright (c) 2007, 2010, 2012 Freescale Semiconductor, Inc.
 * Copyright (c) 2009 MontaVista Software, Inc.
 * Copyright 2020 NXP
 *
 * Authors: Xiaobo Xie <X.Xie@freescale.com>
 *	    Anton Vorontsov <avorontsov@ru.mvista.com>
 */

#include <linux/err.h>
#include <linux/io.h>
#include <linux/of.h>
#include <linux/of_address.h>
#include <linux/delay.h>
#include <linux/module.h>
#include <linux/sys_soc.h>
#include <linux/clk.h>
#include <linux/ktime.h>
#include <linux/dma-mapping.h>
#include <linux/iopoll.h>
#include <linux/mmc/host.h>
#include <linux/mmc/mmc.h>
#include "sdhci-pltfm.h"
#include "sdhci-esdhc.h"

#define VENDOR_V_22	0x12
#define VENDOR_V_23	0x13

#define MMC_TIMING_NUM (MMC_TIMING_MMC_HS400 + 1)

struct esdhc_clk_fixup {
	const unsigned int sd_dflt_max_clk;
	const unsigned int max_clk[MMC_TIMING_NUM];
};

static const struct esdhc_clk_fixup ls1021a_esdhc_clk = {
	.sd_dflt_max_clk = 25000000,
	.max_clk[MMC_TIMING_MMC_HS] = 46500000,
	.max_clk[MMC_TIMING_SD_HS] = 46500000,
};

static const struct esdhc_clk_fixup ls1043a_esdhc_clk = {
	.sd_dflt_max_clk = 25000000,
	.max_clk[MMC_TIMING_UHS_SDR104] = 116700000,
	.max_clk[MMC_TIMING_MMC_HS200] = 116700000,
};

static const struct esdhc_clk_fixup ls1046a_esdhc_clk = {
	.sd_dflt_max_clk = 25000000,
	.max_clk[MMC_TIMING_UHS_SDR104] = 167000000,
	.max_clk[MMC_TIMING_MMC_HS200] = 167000000,
};

static const struct esdhc_clk_fixup ls1012a_esdhc_clk = {
	.sd_dflt_max_clk = 25000000,
	.max_clk[MMC_TIMING_UHS_SDR104] = 125000000,
	.max_clk[MMC_TIMING_MMC_HS200] = 125000000,
};

static const struct esdhc_clk_fixup p1010_esdhc_clk = {
	.sd_dflt_max_clk = 20000000,
	.max_clk[MMC_TIMING_LEGACY] = 20000000,
	.max_clk[MMC_TIMING_MMC_HS] = 42000000,
	.max_clk[MMC_TIMING_SD_HS] = 40000000,
};

static const struct of_device_id sdhci_esdhc_of_match[] = {
	{ .compatible = "fsl,ls1021a-esdhc", .data = &ls1021a_esdhc_clk},
	{ .compatible = "fsl,ls1043a-esdhc", .data = &ls1043a_esdhc_clk},
	{ .compatible = "fsl,ls1046a-esdhc", .data = &ls1046a_esdhc_clk},
	{ .compatible = "fsl,ls1012a-esdhc", .data = &ls1012a_esdhc_clk},
	{ .compatible = "fsl,p1010-esdhc",   .data = &p1010_esdhc_clk},
	{ .compatible = "fsl,mpc8379-esdhc" },
	{ .compatible = "fsl,mpc8536-esdhc" },
	{ .compatible = "fsl,esdhc" },
	{ }
};
MODULE_DEVICE_TABLE(of, sdhci_esdhc_of_match);

struct sdhci_esdhc {
	u8 vendor_ver;
	u8 spec_ver;
	bool quirk_incorrect_hostver;
	bool quirk_limited_clk_division;
	bool quirk_unreliable_pulse_detection;
	bool quirk_tuning_erratum_type1;
	bool quirk_tuning_erratum_type2;
	bool quirk_ignore_data_inhibit;
	bool quirk_delay_before_data_reset;
	bool quirk_trans_complete_erratum;
	bool in_sw_tuning;
	unsigned int peripheral_clock;
	const struct esdhc_clk_fixup *clk_fixup;
	u32 div_ratio;
};

/**
 * esdhc_readl_fixup - Fixup the value read from incompatible eSDHC register
 *		       to make it compatible with SD spec.
 *
 * @host: pointer to sdhci_host
 * @spec_reg: SD spec register address
 * @value: 32bit eSDHC register value on spec_reg address
 *
 * In SD spec, there are 8/16/32/64 bits registers, while all of eSDHC
 * registers are 32 bits. There are differences in register size, register
 * address, register function, bit position and function between eSDHC spec
 * and SD spec.
 *
 * Return a fixed up register value
 */
static u32 esdhc_readl_fixup(struct sdhci_host *host,
				     int spec_reg, u32 value)
{
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_esdhc *esdhc = sdhci_pltfm_priv(pltfm_host);
	u32 ret;

	/*
	 * The bit of ADMA flag in eSDHC is not compatible with standard
	 * SDHC register, so set fake flag SDHCI_CAN_DO_ADMA2 when ADMA is
	 * supported by eSDHC.
	 * And for many FSL eSDHC controller, the reset value of field
	 * SDHCI_CAN_DO_ADMA1 is 1, but some of them can't support ADMA,
	 * only these vendor version is greater than 2.2/0x12 support ADMA.
	 */
	if ((spec_reg == SDHCI_CAPABILITIES) && (value & SDHCI_CAN_DO_ADMA1)) {
		if (esdhc->vendor_ver > VENDOR_V_22) {
			ret = value | SDHCI_CAN_DO_ADMA2;
			return ret;
		}
	}
	/*
	 * The DAT[3:0] line signal levels and the CMD line signal level are
	 * not compatible with standard SDHC register. The line signal levels
	 * DAT[7:0] are at bits 31:24 and the command line signal level is at
	 * bit 23. All other bits are the same as in the standard SDHC
	 * register.
	 */
	if (spec_reg == SDHCI_PRESENT_STATE) {
		ret = value & 0x000fffff;
		ret |= (value >> 4) & SDHCI_DATA_LVL_MASK;
		ret |= (value << 1) & SDHCI_CMD_LVL;
		return ret;
	}

	/*
	 * DTS properties of mmc host are used to enable each speed mode
	 * according to soc and board capability. So clean up
	 * SDR50/SDR104/DDR50 support bits here.
	 */
	if (spec_reg == SDHCI_CAPABILITIES_1) {
		ret = value & ~(SDHCI_SUPPORT_SDR50 | SDHCI_SUPPORT_SDR104 |
				SDHCI_SUPPORT_DDR50);
		return ret;
	}

	/*
	 * Some controllers have unreliable Data Line Active
	 * bit for commands with busy signal. This affects
	 * Command Inhibit (data) bit. Just ignore it since
	 * MMC core driver has already polled card status
	 * with CMD13 after any command with busy siganl.
	 */
	if ((spec_reg == SDHCI_PRESENT_STATE) &&
	(esdhc->quirk_ignore_data_inhibit == true)) {
		ret = value & ~SDHCI_DATA_INHIBIT;
		return ret;
	}

	ret = value;
	return ret;
}

static u16 esdhc_readw_fixup(struct sdhci_host *host,
				     int spec_reg, u32 value)
{
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_esdhc *esdhc = sdhci_pltfm_priv(pltfm_host);
	u16 ret;
	int shift = (spec_reg & 0x2) * 8;

	if (spec_reg == SDHCI_TRANSFER_MODE)
		return pltfm_host->xfer_mode_shadow;

	if (spec_reg == SDHCI_HOST_VERSION)
		ret = value & 0xffff;
	else
		ret = (value >> shift) & 0xffff;
	/* Workaround for T4240-R1.0-R2.0 eSDHC which has incorrect
	 * vendor version and spec version information.
	 */
	if ((spec_reg == SDHCI_HOST_VERSION) &&
	    (esdhc->quirk_incorrect_hostver))
		ret = (VENDOR_V_23 << SDHCI_VENDOR_VER_SHIFT) | SDHCI_SPEC_200;
	return ret;
}

static u8 esdhc_readb_fixup(struct sdhci_host *host,
				     int spec_reg, u32 value)
{
	u8 ret;
	u8 dma_bits;
	int shift = (spec_reg & 0x3) * 8;

	ret = (value >> shift) & 0xff;

	/*
	 * "DMA select" locates at offset 0x28 in SD specification, but on
	 * P5020 or P3041, it locates at 0x29.
	 */
	if (spec_reg == SDHCI_HOST_CONTROL) {
		/* DMA select is 22,23 bits in Protocol Control Register */
		dma_bits = (value >> 5) & SDHCI_CTRL_DMA_MASK;
		/* fixup the result */
		ret &= ~SDHCI_CTRL_DMA_MASK;
		ret |= dma_bits;
	}
	return ret;
}

/**
 * esdhc_writel_fixup - Fixup the SD spec register value so that it could be
 *			written into eSDHC register.
 *
 * @host: pointer to sdhci_host
 * @spec_reg: SD spec register address
 * @value: 8/16/32bit SD spec register value that would be written
 * @old_value: 32bit eSDHC register value on spec_reg address
 *
 * In SD spec, there are 8/16/32/64 bits registers, while all of eSDHC
 * registers are 32 bits. There are differences in register size, register
 * address, register function, bit position and function between eSDHC spec
 * and SD spec.
 *
 * Return a fixed up register value
 */
static u32 esdhc_writel_fixup(struct sdhci_host *host,
				     int spec_reg, u32 value, u32 old_value)
{
	u32 ret;

	/*
	 * Enabling IRQSTATEN[BGESEN] is just to set IRQSTAT[BGE]
	 * when SYSCTL[RSTD] is set for some special operations.
	 * No any impact on other operation.
	 */
	if (spec_reg == SDHCI_INT_ENABLE)
		ret = value | SDHCI_INT_BLK_GAP;
	else
		ret = value;

	return ret;
}

static u32 esdhc_writew_fixup(struct sdhci_host *host,
				     int spec_reg, u16 value, u32 old_value)
{
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	int shift = (spec_reg & 0x2) * 8;
	u32 ret;

	switch (spec_reg) {
	case SDHCI_TRANSFER_MODE:
		/*
		 * Postpone this write, we must do it together with a
		 * command write that is down below. Return old value.
		 */
		pltfm_host->xfer_mode_shadow = value;
		return old_value;
	case SDHCI_COMMAND:
		ret = (value << 16) | pltfm_host->xfer_mode_shadow;
		return ret;
	}

	ret = old_value & (~(0xffff << shift));
	ret |= (value << shift);

	if (spec_reg == SDHCI_BLOCK_SIZE) {
		/*
		 * Two last DMA bits are reserved, and first one is used for
		 * non-standard blksz of 4096 bytes that we don't support
		 * yet. So clear the DMA boundary bits.
		 */
		ret &= (~SDHCI_MAKE_BLKSZ(0x7, 0));
	}
	return ret;
}

static u32 esdhc_writeb_fixup(struct sdhci_host *host,
				     int spec_reg, u8 value, u32 old_value)
{
	u32 ret;
	u32 dma_bits;
	u8 tmp;
	int shift = (spec_reg & 0x3) * 8;

	/*
	 * eSDHC doesn't have a standard power control register, so we do
	 * nothing here to avoid incorrect operation.
	 */
	if (spec_reg == SDHCI_POWER_CONTROL)
		return old_value;
	/*
	 * "DMA select" location is offset 0x28 in SD specification, but on
	 * P5020 or P3041, it's located at 0x29.
	 */
	if (spec_reg == SDHCI_HOST_CONTROL) {
		/*
		 * If host control register is not standard, exit
		 * this function
		 */
		if (host->quirks2 & SDHCI_QUIRK2_BROKEN_HOST_CONTROL)
			return old_value;

		/* DMA select is 22,23 bits in Protocol Control Register */
		dma_bits = (value & SDHCI_CTRL_DMA_MASK) << 5;
		ret = (old_value & (~(SDHCI_CTRL_DMA_MASK << 5))) | dma_bits;
		tmp = (value & (~SDHCI_CTRL_DMA_MASK)) |
		      (old_value & SDHCI_CTRL_DMA_MASK);
		ret = (ret & (~0xff)) | tmp;

		/* Prevent SDHCI core from writing reserved bits (e.g. HISPD) */
		ret &= ~ESDHC_HOST_CONTROL_RES;
		return ret;
	}

	ret = (old_value & (~(0xff << shift))) | (value << shift);
	return ret;
}

static u32 esdhc_be_readl(struct sdhci_host *host, int reg)
{
	u32 ret;
	u32 value;

	if (reg == SDHCI_CAPABILITIES_1)
		value = ioread32be(host->ioaddr + ESDHC_CAPABILITIES_1);
	else
		value = ioread32be(host->ioaddr + reg);

	ret = esdhc_readl_fixup(host, reg, value);

	return ret;
}

static u32 esdhc_le_readl(struct sdhci_host *host, int reg)
{
	u32 ret;
	u32 value;

	if (reg == SDHCI_CAPABILITIES_1)
		value = ioread32(host->ioaddr + ESDHC_CAPABILITIES_1);
	else
		value = ioread32(host->ioaddr + reg);

	ret = esdhc_readl_fixup(host, reg, value);

	return ret;
}

static u16 esdhc_be_readw(struct sdhci_host *host, int reg)
{
	u16 ret;
	u32 value;
	int base = reg & ~0x3;

	value = ioread32be(host->ioaddr + base);
	ret = esdhc_readw_fixup(host, reg, value);
	return ret;
}

static u16 esdhc_le_readw(struct sdhci_host *host, int reg)
{
	u16 ret;
	u32 value;
	int base = reg & ~0x3;

	value = ioread32(host->ioaddr + base);
	ret = esdhc_readw_fixup(host, reg, value);
	return ret;
}

static u8 esdhc_be_readb(struct sdhci_host *host, int reg)
{
	u8 ret;
	u32 value;
	int base = reg & ~0x3;

	value = ioread32be(host->ioaddr + base);
	ret = esdhc_readb_fixup(host, reg, value);
	return ret;
}

static u8 esdhc_le_readb(struct sdhci_host *host, int reg)
{
	u8 ret;
	u32 value;
	int base = reg & ~0x3;

	value = ioread32(host->ioaddr + base);
	ret = esdhc_readb_fixup(host, reg, value);
	return ret;
}

static void esdhc_be_writel(struct sdhci_host *host, u32 val, int reg)
{
	u32 value;

	value = esdhc_writel_fixup(host, reg, val, 0);
	iowrite32be(value, host->ioaddr + reg);
}

static void esdhc_le_writel(struct sdhci_host *host, u32 val, int reg)
{
	u32 value;

	value = esdhc_writel_fixup(host, reg, val, 0);
	iowrite32(value, host->ioaddr + reg);
}

static void esdhc_be_writew(struct sdhci_host *host, u16 val, int reg)
{
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_esdhc *esdhc = sdhci_pltfm_priv(pltfm_host);
	int base = reg & ~0x3;
	u32 value;
	u32 ret;

	value = ioread32be(host->ioaddr + base);
	ret = esdhc_writew_fixup(host, reg, val, value);
	if (reg != SDHCI_TRANSFER_MODE)
		iowrite32be(ret, host->ioaddr + base);

	/* Starting SW tuning requires ESDHC_SMPCLKSEL to be set
	 * 1us later after ESDHC_EXTN is set.
	 */
	if (base == ESDHC_SYSTEM_CONTROL_2) {
		if (!(value & ESDHC_EXTN) && (ret & ESDHC_EXTN) &&
		    esdhc->in_sw_tuning) {
			udelay(1);
			ret |= ESDHC_SMPCLKSEL;
			iowrite32be(ret, host->ioaddr + base);
		}
	}
}

static void esdhc_le_writew(struct sdhci_host *host, u16 val, int reg)
{
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_esdhc *esdhc = sdhci_pltfm_priv(pltfm_host);
	int base = reg & ~0x3;
	u32 value;
	u32 ret;

	value = ioread32(host->ioaddr + base);
	ret = esdhc_writew_fixup(host, reg, val, value);
	if (reg != SDHCI_TRANSFER_MODE)
		iowrite32(ret, host->ioaddr + base);

	/* Starting SW tuning requires ESDHC_SMPCLKSEL to be set
	 * 1us later after ESDHC_EXTN is set.
	 */
	if (base == ESDHC_SYSTEM_CONTROL_2) {
		if (!(value & ESDHC_EXTN) && (ret & ESDHC_EXTN) &&
		    esdhc->in_sw_tuning) {
			udelay(1);
			ret |= ESDHC_SMPCLKSEL;
			iowrite32(ret, host->ioaddr + base);
		}
	}
}

static void esdhc_be_writeb(struct sdhci_host *host, u8 val, int reg)
{
	int base = reg & ~0x3;
	u32 value;
	u32 ret;

	value = ioread32be(host->ioaddr + base);
	ret = esdhc_writeb_fixup(host, reg, val, value);
	iowrite32be(ret, host->ioaddr + base);
}

static void esdhc_le_writeb(struct sdhci_host *host, u8 val, int reg)
{
	int base = reg & ~0x3;
	u32 value;
	u32 ret;

	value = ioread32(host->ioaddr + base);
	ret = esdhc_writeb_fixup(host, reg, val, value);
	iowrite32(ret, host->ioaddr + base);
}

/*
 * For Abort or Suspend after Stop at Block Gap, ignore the ADMA
 * error(IRQSTAT[ADMAE]) if both Transfer Complete(IRQSTAT[TC])
 * and Block Gap Event(IRQSTAT[BGE]) are also set.
 * For Continue, apply soft reset for data(SYSCTL[RSTD]);
 * and re-issue the entire read transaction from beginning.
 */
static void esdhc_of_adma_workaround(struct sdhci_host *host, u32 intmask)
{
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_esdhc *esdhc = sdhci_pltfm_priv(pltfm_host);
	bool applicable;
	dma_addr_t dmastart;
	dma_addr_t dmanow;

	applicable = (intmask & SDHCI_INT_DATA_END) &&
		     (intmask & SDHCI_INT_BLK_GAP) &&
		     (esdhc->vendor_ver == VENDOR_V_23);
	if (!applicable)
		return;

	host->data->error = 0;
	dmastart = sg_dma_address(host->data->sg);
	dmanow = dmastart + host->data->bytes_xfered;
	/*
	 * Force update to the next DMA block boundary.
	 */
	dmanow = (dmanow & ~(SDHCI_DEFAULT_BOUNDARY_SIZE - 1)) +
		SDHCI_DEFAULT_BOUNDARY_SIZE;
	host->data->bytes_xfered = dmanow - dmastart;
	sdhci_writel(host, dmanow, SDHCI_DMA_ADDRESS);
}

static int esdhc_of_enable_dma(struct sdhci_host *host)
{
	int ret;
	u32 value;
	struct device *dev = mmc_dev(host->mmc);

	if (of_device_is_compatible(dev->of_node, "fsl,ls1043a-esdhc") ||
	    of_device_is_compatible(dev->of_node, "fsl,ls1046a-esdhc")) {
		ret = dma_set_mask_and_coherent(dev, DMA_BIT_MASK(40));
		if (ret)
			return ret;
	}

	value = sdhci_readl(host, ESDHC_DMA_SYSCTL);

	if (of_dma_is_coherent(dev->of_node))
		value |= ESDHC_DMA_SNOOP;
	else
		value &= ~ESDHC_DMA_SNOOP;

	sdhci_writel(host, value, ESDHC_DMA_SYSCTL);
	return 0;
}

static unsigned int esdhc_of_get_max_clock(struct sdhci_host *host)
{
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_esdhc *esdhc = sdhci_pltfm_priv(pltfm_host);

	if (esdhc->peripheral_clock)
		return esdhc->peripheral_clock;
	else
		return pltfm_host->clock;
}

static unsigned int esdhc_of_get_min_clock(struct sdhci_host *host)
{
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_esdhc *esdhc = sdhci_pltfm_priv(pltfm_host);
	unsigned int clock;

	if (esdhc->peripheral_clock)
		clock = esdhc->peripheral_clock;
	else
		clock = pltfm_host->clock;
	return clock / 256 / 16;
}

static void esdhc_clock_enable(struct sdhci_host *host, bool enable)
{
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_esdhc *esdhc = sdhci_pltfm_priv(pltfm_host);
	ktime_t timeout;
	u32 val, clk_en;

	clk_en = ESDHC_CLOCK_SDCLKEN;

	/*
	 * IPGEN/HCKEN/PEREN bits exist on eSDHC whose vendor version
	 * is 2.2 or lower.
	 */
	if (esdhc->vendor_ver <= VENDOR_V_22)
		clk_en |= (ESDHC_CLOCK_IPGEN | ESDHC_CLOCK_HCKEN |
			   ESDHC_CLOCK_PEREN);

	val = sdhci_readl(host, ESDHC_SYSTEM_CONTROL);

	if (enable)
		val |= clk_en;
	else
		val &= ~clk_en;

	sdhci_writel(host, val, ESDHC_SYSTEM_CONTROL);

	/*
	 * Wait max 20 ms. If vendor version is 2.2 or lower, do not
	 * wait clock stable bit which does not exist.
	 */
	timeout = ktime_add_ms(ktime_get(), 20);
	while (esdhc->vendor_ver > VENDOR_V_22) {
		bool timedout = ktime_after(ktime_get(), timeout);

		if (sdhci_readl(host, ESDHC_PRSSTAT) & ESDHC_CLOCK_STABLE)
			break;
		if (timedout) {
			pr_err("%s: Internal clock never stabilised.\n",
				mmc_hostname(host->mmc));
			break;
		}
		usleep_range(10, 20);
	}
}

static void esdhc_flush_async_fifo(struct sdhci_host *host)
{
	ktime_t timeout;
	u32 val;

	val = sdhci_readl(host, ESDHC_DMA_SYSCTL);
	val |= ESDHC_FLUSH_ASYNC_FIFO;
	sdhci_writel(host, val, ESDHC_DMA_SYSCTL);

	/* Wait max 20 ms */
	timeout = ktime_add_ms(ktime_get(), 20);
	while (1) {
		bool timedout = ktime_after(ktime_get(), timeout);

		if (!(sdhci_readl(host, ESDHC_DMA_SYSCTL) &
		      ESDHC_FLUSH_ASYNC_FIFO))
			break;
		if (timedout) {
			pr_err("%s: flushing asynchronous FIFO timeout.\n",
				mmc_hostname(host->mmc));
			break;
		}
		usleep_range(10, 20);
	}
}

static void esdhc_of_set_clock(struct sdhci_host *host, unsigned int clock)
{
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_esdhc *esdhc = sdhci_pltfm_priv(pltfm_host);
	unsigned int pre_div = 1, div = 1;
	unsigned int clock_fixup = 0;
	ktime_t timeout;
	u32 temp;

	if (clock == 0) {
		host->mmc->actual_clock = 0;
		esdhc_clock_enable(host, false);
		return;
	}

	/* Start pre_div at 2 for vendor version < 2.3. */
	if (esdhc->vendor_ver < VENDOR_V_23)
		pre_div = 2;

	/* Fix clock value. */
	if (host->mmc->card && mmc_card_sd(host->mmc->card) &&
	    esdhc->clk_fixup && host->mmc->ios.timing == MMC_TIMING_LEGACY)
		clock_fixup = esdhc->clk_fixup->sd_dflt_max_clk;
	else if (esdhc->clk_fixup)
		clock_fixup = esdhc->clk_fixup->max_clk[host->mmc->ios.timing];

	if (clock_fixup == 0 || clock < clock_fixup)
		clock_fixup = clock;

	/* Calculate pre_div and div. */
	while (host->max_clk / pre_div / 16 > clock_fixup && pre_div < 256)
		pre_div *= 2;

	while (host->max_clk / pre_div / div > clock_fixup && div < 16)
		div++;

	esdhc->div_ratio = pre_div * div;

	/* Limit clock division for HS400 200MHz clock for quirk. */
	if (esdhc->quirk_limited_clk_division &&
	    clock == MMC_HS200_MAX_DTR &&
	    (host->mmc->ios.timing == MMC_TIMING_MMC_HS400 ||
	     host->flags & SDHCI_HS400_TUNING)) {
		if (esdhc->div_ratio <= 4) {
			pre_div = 4;
			div = 1;
		} else if (esdhc->div_ratio <= 8) {
			pre_div = 4;
			div = 2;
		} else if (esdhc->div_ratio <= 12) {
			pre_div = 4;
			div = 3;
		} else {
			pr_warn("%s: using unsupported clock division.\n",
				mmc_hostname(host->mmc));
		}
		esdhc->div_ratio = pre_div * div;
	}

	host->mmc->actual_clock = host->max_clk / esdhc->div_ratio;

	dev_dbg(mmc_dev(host->mmc), "desired SD clock: %d, actual: %d\n",
		clock, host->mmc->actual_clock);

	/* Set clock division into register. */
	pre_div >>= 1;
	div--;

	esdhc_clock_enable(host, false);

	temp = sdhci_readl(host, ESDHC_SYSTEM_CONTROL);
	temp &= ~ESDHC_CLOCK_MASK;
	temp |= ((div << ESDHC_DIVIDER_SHIFT) |
		(pre_div << ESDHC_PREDIV_SHIFT));
	sdhci_writel(host, temp, ESDHC_SYSTEM_CONTROL);

	/*
	 * Wait max 20 ms. If vendor version is 2.2 or lower, do not
	 * wait clock stable bit which does not exist.
	 */
	timeout = ktime_add_ms(ktime_get(), 20);
	while (esdhc->vendor_ver > VENDOR_V_22) {
		bool timedout = ktime_after(ktime_get(), timeout);

		if (sdhci_readl(host, ESDHC_PRSSTAT) & ESDHC_CLOCK_STABLE)
			break;
		if (timedout) {
			pr_err("%s: Internal clock never stabilised.\n",
				mmc_hostname(host->mmc));
			break;
		}
		usleep_range(10, 20);
	}

	/* Additional setting for HS400. */
	if (host->mmc->ios.timing == MMC_TIMING_MMC_HS400 &&
	    clock == MMC_HS200_MAX_DTR) {
		temp = sdhci_readl(host, ESDHC_TBCTL);
		sdhci_writel(host, temp | ESDHC_HS400_MODE, ESDHC_TBCTL);
		temp = sdhci_readl(host, ESDHC_SDCLKCTL);
		sdhci_writel(host, temp | ESDHC_CMD_CLK_CTL, ESDHC_SDCLKCTL);
		esdhc_clock_enable(host, true);

		temp = sdhci_readl(host, ESDHC_DLLCFG0);
		temp |= ESDHC_DLL_ENABLE;
		if (host->mmc->actual_clock == MMC_HS200_MAX_DTR)
			temp |= ESDHC_DLL_FREQ_SEL;
		sdhci_writel(host, temp, ESDHC_DLLCFG0);

		temp |= ESDHC_DLL_RESET;
		sdhci_writel(host, temp, ESDHC_DLLCFG0);
		udelay(1);
		temp &= ~ESDHC_DLL_RESET;
		sdhci_writel(host, temp, ESDHC_DLLCFG0);

		/* Wait max 20 ms */
		if (read_poll_timeout(sdhci_readl, temp,
				      temp & ESDHC_DLL_STS_SLV_LOCK,
				      10, 20000, false,
				      host, ESDHC_DLLSTAT0))
			pr_err("%s: timeout for delay chain lock.\n",
			       mmc_hostname(host->mmc));

		temp = sdhci_readl(host, ESDHC_TBCTL);
		sdhci_writel(host, temp | ESDHC_HS400_WNDW_ADJUST, ESDHC_TBCTL);

		esdhc_clock_enable(host, false);
		esdhc_flush_async_fifo(host);
	}
	esdhc_clock_enable(host, true);
}

static void esdhc_pltfm_set_bus_width(struct sdhci_host *host, int width)
{
	u32 ctrl;

	ctrl = sdhci_readl(host, ESDHC_PROCTL);
	ctrl &= (~ESDHC_CTRL_BUSWIDTH_MASK);
	switch (width) {
	case MMC_BUS_WIDTH_8:
		ctrl |= ESDHC_CTRL_8BITBUS;
		break;

	case MMC_BUS_WIDTH_4:
		ctrl |= ESDHC_CTRL_4BITBUS;
		break;

	default:
		break;
	}

	sdhci_writel(host, ctrl, ESDHC_PROCTL);
}

static void esdhc_reset(struct sdhci_host *host, u8 mask)
{
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_esdhc *esdhc = sdhci_pltfm_priv(pltfm_host);
	u32 val, bus_width = 0;

	/*
	 * Add delay to make sure all the DMA transfers are finished
	 * for quirk.
	 */
	if (esdhc->quirk_delay_before_data_reset &&
	    (mask & SDHCI_RESET_DATA) &&
	    (host->flags & SDHCI_REQ_USE_DMA))
		mdelay(5);

	/*
	 * Save bus-width for eSDHC whose vendor version is 2.2
	 * or lower for data reset.
	 */
	if ((mask & SDHCI_RESET_DATA) &&
	    (esdhc->vendor_ver <= VENDOR_V_22)) {
		val = sdhci_readl(host, ESDHC_PROCTL);
		bus_width = val & ESDHC_CTRL_BUSWIDTH_MASK;
	}

	sdhci_reset(host, mask);

	/*
	 * Restore bus-width setting and interrupt registers for eSDHC
	 * whose vendor version is 2.2 or lower for data reset.
	 */
	if ((mask & SDHCI_RESET_DATA) &&
	    (esdhc->vendor_ver <= VENDOR_V_22)) {
		val = sdhci_readl(host, ESDHC_PROCTL);
		val &= ~ESDHC_CTRL_BUSWIDTH_MASK;
		val |= bus_width;
		sdhci_writel(host, val, ESDHC_PROCTL);

		sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
		sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
	}

	/*
	 * Some bits have to be cleaned manually for eSDHC whose spec
	 * version is higher than 3.0 for all reset.
	 */
	if ((mask & SDHCI_RESET_ALL) &&
	    (esdhc->spec_ver >= SDHCI_SPEC_300)) {
		val = sdhci_readl(host, ESDHC_TBCTL);
		val &= ~ESDHC_TB_EN;
		sdhci_writel(host, val, ESDHC_TBCTL);

		/*
		 * Initialize eSDHC_DLLCFG1[DLL_PD_PULSE_STRETCH_SEL] to
		 * 0 for quirk.
		 */
		if (esdhc->quirk_unreliable_pulse_detection) {
			val = sdhci_readl(host, ESDHC_DLLCFG1);
			val &= ~ESDHC_DLL_PD_PULSE_STRETCH_SEL;
			sdhci_writel(host, val, ESDHC_DLLCFG1);
		}
	}
}

/* The SCFG, Supplemental Configuration Unit, provides SoC specific
 * configuration and status registers for the device. There is a
 * SDHC IO VSEL control register on SCFG for some platforms. It's
 * used to support SDHC IO voltage switching.
 */
static const struct of_device_id scfg_device_ids[] = {
	{ .compatible = "fsl,t1040-scfg", },
	{ .compatible = "fsl,ls1012a-scfg", },
	{ .compatible = "fsl,ls1046a-scfg", },
	{}
};

/* SDHC IO VSEL control register definition */
#define SCFG_SDHCIOVSELCR	0x408
#define SDHCIOVSELCR_TGLEN	0x80000000
#define SDHCIOVSELCR_VSELVAL	0x60000000
#define SDHCIOVSELCR_SDHC_VS	0x00000001

static int esdhc_signal_voltage_switch(struct mmc_host *mmc,
				       struct mmc_ios *ios)
{
	struct sdhci_host *host = mmc_priv(mmc);
	struct device_node *scfg_node;
	void __iomem *scfg_base = NULL;
	u32 sdhciovselcr;
	u32 val;

	/*
	 * Signal Voltage Switching is only applicable for Host Controllers
	 * v3.00 and above.
	 */
	if (host->version < SDHCI_SPEC_300)
		return 0;

	val = sdhci_readl(host, ESDHC_PROCTL);

	switch (ios->signal_voltage) {
	case MMC_SIGNAL_VOLTAGE_330:
		val &= ~ESDHC_VOLT_SEL;
		sdhci_writel(host, val, ESDHC_PROCTL);
		return 0;
	case MMC_SIGNAL_VOLTAGE_180:
		scfg_node = of_find_matching_node(NULL, scfg_device_ids);
		if (scfg_node)
			scfg_base = of_iomap(scfg_node, 0);
		of_node_put(scfg_node);
		if (scfg_base) {
			sdhciovselcr = SDHCIOVSELCR_TGLEN |
				       SDHCIOVSELCR_VSELVAL;
			iowrite32be(sdhciovselcr,
				scfg_base + SCFG_SDHCIOVSELCR);

			val |= ESDHC_VOLT_SEL;
			sdhci_writel(host, val, ESDHC_PROCTL);
			mdelay(5);

			sdhciovselcr = SDHCIOVSELCR_TGLEN |
				       SDHCIOVSELCR_SDHC_VS;
			iowrite32be(sdhciovselcr,
				scfg_base + SCFG_SDHCIOVSELCR);
			iounmap(scfg_base);
		} else {
			val |= ESDHC_VOLT_SEL;
			sdhci_writel(host, val, ESDHC_PROCTL);
		}
		return 0;
	default:
		return 0;
	}
}

static struct soc_device_attribute soc_tuning_erratum_type1[] = {
	{ .family = "QorIQ T1023", },
	{ .family = "QorIQ T1040", },
	{ .family = "QorIQ T2080", },
	{ .family = "QorIQ LS1021A", },
	{ /* sentinel */ }
};

static struct soc_device_attribute soc_tuning_erratum_type2[] = {
	{ .family = "QorIQ LS1012A", },
	{ .family = "QorIQ LS1043A", },
	{ .family = "QorIQ LS1046A", },
	{ .family = "QorIQ LS1080A", },
	{ .family = "QorIQ LS2080A", },
	{ .family = "QorIQ LA1575A", },
	{ /* sentinel */ }
};

static void esdhc_tuning_block_enable(struct sdhci_host *host, bool enable)
{
	u32 val;

	esdhc_clock_enable(host, false);
	esdhc_flush_async_fifo(host);

	val = sdhci_readl(host, ESDHC_TBCTL);
	if (enable)
		val |= ESDHC_TB_EN;
	else
		val &= ~ESDHC_TB_EN;
	sdhci_writel(host, val, ESDHC_TBCTL);

	esdhc_clock_enable(host, true);
}

static void esdhc_tuning_window_ptr(struct sdhci_host *host, u8 *window_start,
				    u8 *window_end)
{
	u32 val;

	/* Write TBCTL[11:8]=4'h8 */
	val = sdhci_readl(host, ESDHC_TBCTL);
	val &= ~(0xf << 8);
	val |= 8 << 8;
	sdhci_writel(host, val, ESDHC_TBCTL);

	mdelay(1);

	/* Read TBCTL[31:0] register and rewrite again */
	val = sdhci_readl(host, ESDHC_TBCTL);
	sdhci_writel(host, val, ESDHC_TBCTL);

	mdelay(1);

	/* Read the TBSTAT[31:0] register twice */
	val = sdhci_readl(host, ESDHC_TBSTAT);
	val = sdhci_readl(host, ESDHC_TBSTAT);

	*window_end = val & 0xff;
	*window_start = (val >> 8) & 0xff;
}

static void esdhc_prepare_sw_tuning(struct sdhci_host *host, u8 *window_start,
				    u8 *window_end)
{
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_esdhc *esdhc = sdhci_pltfm_priv(pltfm_host);
	u8 start_ptr, end_ptr;

	if (esdhc->quirk_tuning_erratum_type1) {
		*window_start = 5 * esdhc->div_ratio;
		*window_end = 3 * esdhc->div_ratio;
		return;
	}

	esdhc_tuning_window_ptr(host, &start_ptr, &end_ptr);

	/* Reset data lines by setting ESDHCCTL[RSTD] */
	sdhci_reset(host, SDHCI_RESET_DATA);
	/* Write 32'hFFFF_FFFF to IRQSTAT register */
	sdhci_writel(host, 0xFFFFFFFF, SDHCI_INT_STATUS);

	/* If TBSTAT[15:8]-TBSTAT[7:0] > (4 * div_ratio) + 2
	 * or TBSTAT[7:0]-TBSTAT[15:8] > (4 * div_ratio) + 2,
	 * then program TBPTR[TB_WNDW_END_PTR] = 4 * div_ratio
	 * and program TBPTR[TB_WNDW_START_PTR] = 8 * div_ratio.
	 */

	if (abs(start_ptr - end_ptr) > (4 * esdhc->div_ratio + 2)) {
		*window_start = 8 * esdhc->div_ratio;
		*window_end = 4 * esdhc->div_ratio;
	} else {
		*window_start = 5 * esdhc->div_ratio;
		*window_end = 3 * esdhc->div_ratio;
	}
}

static int esdhc_execute_sw_tuning(struct mmc_host *mmc, u32 opcode,
				   u8 window_start, u8 window_end)
{
	struct sdhci_host *host = mmc_priv(mmc);
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_esdhc *esdhc = sdhci_pltfm_priv(pltfm_host);
	u32 val;
	int ret;

	/* Program TBPTR[TB_WNDW_END_PTR] and TBPTR[TB_WNDW_START_PTR] */
	val = ((u32)window_start << ESDHC_WNDW_STRT_PTR_SHIFT) &
	      ESDHC_WNDW_STRT_PTR_MASK;
	val |= window_end & ESDHC_WNDW_END_PTR_MASK;
	sdhci_writel(host, val, ESDHC_TBPTR);

	/* Program the software tuning mode by setting TBCTL[TB_MODE]=2'h3 */
	val = sdhci_readl(host, ESDHC_TBCTL);
	val &= ~ESDHC_TB_MODE_MASK;
	val |= ESDHC_TB_MODE_SW;
	sdhci_writel(host, val, ESDHC_TBCTL);

	esdhc->in_sw_tuning = true;
	ret = sdhci_execute_tuning(mmc, opcode);
	esdhc->in_sw_tuning = false;
	return ret;
}

static int esdhc_execute_tuning(struct mmc_host *mmc, u32 opcode)
{
	struct sdhci_host *host = mmc_priv(mmc);
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_esdhc *esdhc = sdhci_pltfm_priv(pltfm_host);
	u8 window_start, window_end;
	int ret, retries = 1;
	bool hs400_tuning;
	unsigned int clk;
	u32 val;

	/* For tuning mode, the sd clock divisor value
	 * must be larger than 3 according to reference manual.
	 */
	clk = esdhc->peripheral_clock / 3;
	if (host->clock > clk)
		esdhc_of_set_clock(host, clk);

	esdhc_tuning_block_enable(host, true);

	/*
	 * The eSDHC controller takes the data timeout value into account
	 * during tuning. If the SD card is too slow sending the response, the
	 * timer will expire and a "Buffer Read Ready" interrupt without data
	 * is triggered. This leads to tuning errors.
	 *
	 * Just set the timeout to the maximum value because the core will
	 * already take care of it in sdhci_send_tuning().
	 */
	sdhci_writeb(host, 0xe, SDHCI_TIMEOUT_CONTROL);

	hs400_tuning = host->flags & SDHCI_HS400_TUNING;

	do {
		if (esdhc->quirk_limited_clk_division &&
		    hs400_tuning)
			esdhc_of_set_clock(host, host->clock);

		/* Do HW tuning */
		val = sdhci_readl(host, ESDHC_TBCTL);
		val &= ~ESDHC_TB_MODE_MASK;
		val |= ESDHC_TB_MODE_3;
		sdhci_writel(host, val, ESDHC_TBCTL);

		ret = sdhci_execute_tuning(mmc, opcode);
		if (ret)
			break;

		/* For type2 affected platforms of the tuning erratum,
		 * tuning may succeed although eSDHC might not have
		 * tuned properly. Need to check tuning window.
		 */
		if (esdhc->quirk_tuning_erratum_type2 &&
		    !host->tuning_err) {
			esdhc_tuning_window_ptr(host, &window_start,
						&window_end);
			if (abs(window_start - window_end) >
			    (4 * esdhc->div_ratio + 2))
				host->tuning_err = -EAGAIN;
		}

		/* If HW tuning fails and triggers erratum,
		 * try workaround.
		 */
		ret = host->tuning_err;
		if (ret == -EAGAIN &&
		    (esdhc->quirk_tuning_erratum_type1 ||
		     esdhc->quirk_tuning_erratum_type2)) {
			/* Recover HS400 tuning flag */
			if (hs400_tuning)
				host->flags |= SDHCI_HS400_TUNING;
			pr_info("%s: Hold on to use fixed sampling clock. Try SW tuning!\n",
				mmc_hostname(mmc));
			/* Do SW tuning */
			esdhc_prepare_sw_tuning(host, &window_start,
						&window_end);
			ret = esdhc_execute_sw_tuning(mmc, opcode,
						      window_start,
						      window_end);
			if (ret)
				break;

			/* Retry both HW/SW tuning with reduced clock. */
			ret = host->tuning_err;
			if (ret == -EAGAIN && retries) {
				/* Recover HS400 tuning flag */
				if (hs400_tuning)
					host->flags |= SDHCI_HS400_TUNING;

				clk = host->max_clk / (esdhc->div_ratio + 1);
				esdhc_of_set_clock(host, clk);
				pr_info("%s: Hold on to use fixed sampling clock. Try tuning with reduced clock!\n",
					mmc_hostname(mmc));
			} else {
				break;
			}
		} else {
			break;
		}
	} while (retries--);

	if (ret) {
		esdhc_tuning_block_enable(host, false);
	} else if (hs400_tuning) {
		val = sdhci_readl(host, ESDHC_SDTIMNGCTL);
		val |= ESDHC_FLW_CTL_BG;
		sdhci_writel(host, val, ESDHC_SDTIMNGCTL);
	}

	return ret;
}

static void esdhc_set_uhs_signaling(struct sdhci_host *host,
				   unsigned int timing)
{
	u32 val;

	/*
	 * There are specific registers setting for HS400 mode.
	 * Clean all of them if controller is in HS400 mode to
	 * exit HS400 mode before re-setting any speed mode.
	 */
	val = sdhci_readl(host, ESDHC_TBCTL);
	if (val & ESDHC_HS400_MODE) {
		val = sdhci_readl(host, ESDHC_SDTIMNGCTL);
		val &= ~ESDHC_FLW_CTL_BG;
		sdhci_writel(host, val, ESDHC_SDTIMNGCTL);

		val = sdhci_readl(host, ESDHC_SDCLKCTL);
		val &= ~ESDHC_CMD_CLK_CTL;
		sdhci_writel(host, val, ESDHC_SDCLKCTL);

		esdhc_clock_enable(host, false);
		val = sdhci_readl(host, ESDHC_TBCTL);
		val &= ~ESDHC_HS400_MODE;
		sdhci_writel(host, val, ESDHC_TBCTL);
		esdhc_clock_enable(host, true);

		val = sdhci_readl(host, ESDHC_DLLCFG0);
		val &= ~(ESDHC_DLL_ENABLE | ESDHC_DLL_FREQ_SEL);
		sdhci_writel(host, val, ESDHC_DLLCFG0);

		val = sdhci_readl(host, ESDHC_TBCTL);
		val &= ~ESDHC_HS400_WNDW_ADJUST;
		sdhci_writel(host, val, ESDHC_TBCTL);

		esdhc_tuning_block_enable(host, false);
	}

	if (timing == MMC_TIMING_MMC_HS400)
		esdhc_tuning_block_enable(host, true);
	else
		sdhci_set_uhs_signaling(host, timing);
}

static u32 esdhc_irq(struct sdhci_host *host, u32 intmask)
{
	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
	struct sdhci_esdhc *esdhc = sdhci_pltfm_priv(pltfm_host);
	u32 command;

	if (esdhc->quirk_trans_complete_erratum) {
		command = SDHCI_GET_CMD(sdhci_readw(host,
					SDHCI_COMMAND));
		if (command == MMC_WRITE_MULTIPLE_BLOCK &&
				sdhci_readw(host, SDHCI_BLOCK_COUNT) &&
				intmask & SDHCI_INT_DATA_END) {
			intmask &= ~SDHCI_INT_DATA_END;
			sdhci_writel(host, SDHCI_INT_DATA_END,
					SDHCI_INT_STATUS);
		}
	}
	return intmask;
}

#ifdef CONFIG_PM_SLEEP
static u32 esdhc_proctl;
static int esdhc_of_suspend(struct device *dev)
{
	struct sdhci_host *host = dev_get_drvdata(dev);

	esdhc_proctl = sdhci_readl(host, SDHCI_HOST_CONTROL);

	if (host->tuning_mode != SDHCI_TUNING_MODE_3)
		mmc_retune_needed(host->mmc);

	return sdhci_suspend_host(host);
}

static int esdhc_of_resume(struct device *dev)
{
	struct sdhci_host *host = dev_get_drvdata(dev);
	int ret = sdhci_resume_host(host);

	if (ret == 0) {
		/* Isn't this already done by sdhci_resume_host() ? --rmk */
		esdhc_of_enable_dma(host);
		sdhci_writel(host, esdhc_proctl, SDHCI_HOST_CONTROL);
	}
	return ret;
}
#endif

static SIMPLE_DEV_PM_OPS(esdhc_of_dev_pm_ops,
			esdhc_of_suspend,
			esdhc_of_resume);

static const struct sdhci_ops sdhci_esdhc_be_ops = {
	.read_l = esdhc_be_readl,
	.read_w = esdhc_be_readw,
	.read_b = esdhc_be_readb,
	.write_l = esdhc_be_writel,
	.write_w = esdhc_be_writew,
	.write_b = esdhc_be_writeb,
	.set_clock = esdhc_of_set_clock,
	.enable_dma = esdhc_of_enable_dma,
	.get_max_clock = esdhc_of_get_max_clock,
	.get_min_clock = esdhc_of_get_min_clock,
	.adma_workaround = esdhc_of_adma_workaround,
	.set_bus_width = esdhc_pltfm_set_bus_width,
	.reset = esdhc_reset,
	.set_uhs_signaling = esdhc_set_uhs_signaling,
	.irq = esdhc_irq,
};

static const struct sdhci_ops sdhci_esdhc_le_ops = {
	.read_l = esdhc_le_readl,
	.read_w = esdhc_le_readw,
	.read_b = esdhc_le_readb,
	.write_l = esdhc_le_writel,
	.write_w = esdhc_le_writew,
	.write_b = esdhc_le_writeb,
	.set_clock = esdhc_of_set_clock,
	.enable_dma = esdhc_of_enable_dma,
	.get_max_clock = esdhc_of_get_max_clock,
	.get_min_clock = esdhc_of_get_min_clock,
	.adma_workaround = esdhc_of_adma_workaround,
	.set_bus_width = esdhc_pltfm_set_bus_width,
	.reset = esdhc_reset,
	.set_uhs_signaling = esdhc_set_uhs_signaling,
	.irq = esdhc_irq,
};

static const struct sdhci_pltfm_data sdhci_esdhc_be_pdata = {
	.quirks = ESDHC_DEFAULT_QUIRKS |
#ifdef CONFIG_PPC
		  SDHCI_QUIRK_BROKEN_CARD_DETECTION |
#endif
		  SDHCI_QUIRK_NO_CARD_NO_RESET |
		  SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC,
	.ops = &sdhci_esdhc_be_ops,
};

static const struct sdhci_pltfm_data sdhci_esdhc_le_pdata = {
	.quirks = ESDHC_DEFAULT_QUIRKS |
		  SDHCI_QUIRK_NO_CARD_NO_RESET |
		  SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC,
	.ops = &sdhci_esdhc_le_ops,
};

static struct soc_device_attribute soc_incorrect_hostver[] = {
	{ .family = "QorIQ T4240", .revision = "1.0", },
	{ .family = "QorIQ T4240", .revision = "2.0", },
	{ /* sentinel */ }
};

static struct soc_device_attribute soc_fixup_sdhc_clkdivs[] = {
	{ .family = "QorIQ LX2160A", .revision = "1.0", },
	{ .family = "QorIQ LX2160A", .revision = "2.0", },
	{ .family = "QorIQ LS1028A", .revision = "1.0", },
	{ /* sentinel */ }
};

static struct soc_device_attribute soc_unreliable_pulse_detection[] = {
	{ .family = "QorIQ LX2160A", .revision = "1.0", },
	{ .family = "QorIQ LX2160A", .revision = "2.0", },
	{ .family = "QorIQ LS1028A", .revision = "1.0", },
	{ /* sentinel */ }
};

static void esdhc_init(struct platform_device *pdev, struct sdhci_host *host)
{
	const struct of_device_id *match;
	struct sdhci_pltfm_host *pltfm_host;
	struct sdhci_esdhc *esdhc;
	struct device_node *np;
	struct clk *clk;
	u32 val;
	u16 host_ver;

	pltfm_host = sdhci_priv(host);
	esdhc = sdhci_pltfm_priv(pltfm_host);

	host_ver = sdhci_readw(host, SDHCI_HOST_VERSION);
	esdhc->vendor_ver = (host_ver & SDHCI_VENDOR_VER_MASK) >>
			     SDHCI_VENDOR_VER_SHIFT;
	esdhc->spec_ver = host_ver & SDHCI_SPEC_VER_MASK;
	if (soc_device_match(soc_incorrect_hostver))
		esdhc->quirk_incorrect_hostver = true;
	else
		esdhc->quirk_incorrect_hostver = false;

	if (soc_device_match(soc_fixup_sdhc_clkdivs))
		esdhc->quirk_limited_clk_division = true;
	else
		esdhc->quirk_limited_clk_division = false;

	if (soc_device_match(soc_unreliable_pulse_detection))
		esdhc->quirk_unreliable_pulse_detection = true;
	else
		esdhc->quirk_unreliable_pulse_detection = false;

	match = of_match_node(sdhci_esdhc_of_match, pdev->dev.of_node);
	if (match)
		esdhc->clk_fixup = match->data;
	np = pdev->dev.of_node;

	if (of_device_is_compatible(np, "fsl,p2020-esdhc")) {
		esdhc->quirk_delay_before_data_reset = true;
		esdhc->quirk_trans_complete_erratum = true;
	}

	clk = of_clk_get(np, 0);
	if (!IS_ERR(clk)) {
		/*
		 * esdhc->peripheral_clock would be assigned with a value
		 * which is eSDHC base clock when use periperal clock.
		 * For some platforms, the clock value got by common clk
		 * API is peripheral clock while the eSDHC base clock is
		 * 1/2 peripheral clock.
		 */
		if (of_device_is_compatible(np, "fsl,ls1046a-esdhc") ||
		    of_device_is_compatible(np, "fsl,ls1028a-esdhc") ||
		    of_device_is_compatible(np, "fsl,ls1088a-esdhc"))
			esdhc->peripheral_clock = clk_get_rate(clk) / 2;
		else
			esdhc->peripheral_clock = clk_get_rate(clk);

		clk_put(clk);
	}

	esdhc_clock_enable(host, false);
	val = sdhci_readl(host, ESDHC_DMA_SYSCTL);
	/*
	 * This bit is not able to be reset by SDHCI_RESET_ALL. Need to
	 * initialize it as 1 or 0 once, to override the different value
	 * which may be configured in bootloader.
	 */
	if (esdhc->peripheral_clock)
		val |= ESDHC_PERIPHERAL_CLK_SEL;
	else
		val &= ~ESDHC_PERIPHERAL_CLK_SEL;
	sdhci_writel(host, val, ESDHC_DMA_SYSCTL);
	esdhc_clock_enable(host, true);
}

static int esdhc_hs400_prepare_ddr(struct mmc_host *mmc)
{
	esdhc_tuning_block_enable(mmc_priv(mmc), false);
	return 0;
}

static int sdhci_esdhc_probe(struct platform_device *pdev)
{
	struct sdhci_host *host;
	struct device_node *np, *tp;
	struct sdhci_pltfm_host *pltfm_host;
	struct sdhci_esdhc *esdhc;
	int ret;

	np = pdev->dev.of_node;

	if (of_property_read_bool(np, "little-endian"))
		host = sdhci_pltfm_init(pdev, &sdhci_esdhc_le_pdata,
					sizeof(struct sdhci_esdhc));
	else
		host = sdhci_pltfm_init(pdev, &sdhci_esdhc_be_pdata,
					sizeof(struct sdhci_esdhc));

	if (IS_ERR(host))
		return PTR_ERR(host);

	host->mmc_host_ops.start_signal_voltage_switch =
		esdhc_signal_voltage_switch;
	host->mmc_host_ops.execute_tuning = esdhc_execute_tuning;
	host->mmc_host_ops.hs400_prepare_ddr = esdhc_hs400_prepare_ddr;
	host->tuning_delay = 1;

	esdhc_init(pdev, host);

	sdhci_get_of_property(pdev);

	pltfm_host = sdhci_priv(host);
	esdhc = sdhci_pltfm_priv(pltfm_host);
	if (soc_device_match(soc_tuning_erratum_type1))
		esdhc->quirk_tuning_erratum_type1 = true;
	else
		esdhc->quirk_tuning_erratum_type1 = false;

	if (soc_device_match(soc_tuning_erratum_type2))
		esdhc->quirk_tuning_erratum_type2 = true;
	else
		esdhc->quirk_tuning_erratum_type2 = false;

	if (esdhc->vendor_ver == VENDOR_V_22)
		host->quirks2 |= SDHCI_QUIRK2_HOST_NO_CMD23;

	if (esdhc->vendor_ver > VENDOR_V_22)
		host->quirks &= ~SDHCI_QUIRK_NO_BUSY_IRQ;

	tp = of_find_compatible_node(NULL, NULL, "fsl,p2020-esdhc");
	if (tp) {
		of_node_put(tp);
		host->quirks |= SDHCI_QUIRK_RESET_AFTER_REQUEST;
		host->quirks |= SDHCI_QUIRK_BROKEN_TIMEOUT_VAL;
	}

	if (of_device_is_compatible(np, "fsl,p5040-esdhc") ||
	    of_device_is_compatible(np, "fsl,p5020-esdhc") ||
	    of_device_is_compatible(np, "fsl,p4080-esdhc") ||
	    of_device_is_compatible(np, "fsl,p1020-esdhc") ||
	    of_device_is_compatible(np, "fsl,t1040-esdhc"))
		host->quirks &= ~SDHCI_QUIRK_BROKEN_CARD_DETECTION;

	if (of_device_is_compatible(np, "fsl,ls1021a-esdhc"))
		host->quirks |= SDHCI_QUIRK_BROKEN_TIMEOUT_VAL;

	esdhc->quirk_ignore_data_inhibit = false;
	if (of_device_is_compatible(np, "fsl,p2020-esdhc")) {
		/*
		 * Freescale messed up with P2020 as it has a non-standard
		 * host control register
		 */
		host->quirks2 |= SDHCI_QUIRK2_BROKEN_HOST_CONTROL;
		esdhc->quirk_ignore_data_inhibit = true;
	}

	/* call to generic mmc_of_parse to support additional capabilities */
	ret = mmc_of_parse(host->mmc);
	if (ret)
		goto err;

	mmc_of_parse_voltage(host->mmc, &host->ocr_mask);

	ret = sdhci_add_host(host);
	if (ret)
		goto err;

	return 0;
 err:
	sdhci_pltfm_free(pdev);
	return ret;
}

static struct platform_driver sdhci_esdhc_driver = {
	.driver = {
		.name = "sdhci-esdhc",
		.probe_type = PROBE_PREFER_ASYNCHRONOUS,
		.of_match_table = sdhci_esdhc_of_match,
		.pm = &esdhc_of_dev_pm_ops,
	},
	.probe = sdhci_esdhc_probe,
	.remove = sdhci_pltfm_unregister,
};

module_platform_driver(sdhci_esdhc_driver);

MODULE_DESCRIPTION("SDHCI OF driver for Freescale MPC eSDHC");
MODULE_AUTHOR("Xiaobo Xie <X.Xie@freescale.com>, "
	      "Anton Vorontsov <avorontsov@ru.mvista.com>");
MODULE_LICENSE("GPL v2");