Documentation/devicetree/bindings/phy/apm-xgene-phy.txt

* APM X-Gene 15Gbps Multi-purpose PHY nodes

PHY nodes are defined to describe on-chip 15Gbps Multi-purpose PHY. Each
PHY (pair of lanes) has its own node.

Required properties:
- compatible		: Shall be "apm,xgene-phy".
- reg			: PHY memory resource is the SDS PHY access resource.
- #phy-cells		: Shall be 1 as it expects one argument for setting
			  the mode of the PHY. Possible values are 0 (SATA),
			  1 (SGMII), 2 (PCIe), 3 (USB), and 4 (XFI).

Optional properties:
- status		: Shall be "ok" if enabled or "disabled" if disabled.
			  Default is "ok".
- clocks		: Reference to the clock entry.
- apm,tx-eye-tuning	: Manual control to fine tune the capture of the serial
			  bit lines from the automatic calibrated position.
			  Two set of 3-tuple setting for each (up to 3)
			  supported link speed on the host. Range from 0 to
			  127 in unit of one bit period. Default is 10.
- apm,tx-eye-direction	: Eye tuning manual control direction. 0 means sample
			  data earlier than the nominal sampling point. 1 means
			  sample data later than the nominal sampling point.
			  Two set of 3-tuple setting for each (up to 3)
			  supported link speed on the host. Default is 0.
- apm,tx-boost-gain	: Frequency boost AC (LSB 3-bit) and DC (2-bit)
			  gain control. Two set of 3-tuple setting for each
			  (up to 3) supported link speed on the host. Range is
			  between 0 to 31 in unit of dB. Default is 3.
- apm,tx-amplitude	: Amplitude control. Two set of 3-tuple setting for
			  each (up to 3) supported link speed on the host.
			  Range is between 0 to 199500 in unit of uV.
			  Default is 199500 uV.
- apm,tx-pre-cursor1	: 1st pre-cursor emphasis taps control. Two set of
			  3-tuple setting for each (up to 3) supported link
			  speed on the host. Range is 0 to 273000 in unit of
			  uV. Default is 0.
- apm,tx-pre-cursor2	: 2nd pre-cursor emphasis taps control. Two set of
			  3-tuple setting for each (up to 3) supported link
			  speed on the host. Range is 0 to 127400 in unit uV.
			  Default is 0x0.
- apm,tx-post-cursor	: Post-cursor emphasis taps control. Two set of
			  3-tuple setting for Gen1, Gen2, and Gen3. Range is
			  between 0 to 0x1f in unit of 18.2mV. Default is 0xf.
- apm,tx-speed		: Tx operating speed. One set of 3-tuple for each
			  supported link speed on the host.
			   0 = 1-2Gbps
			   1 = 2-4Gbps (1st tuple default)
			   2 = 4-8Gbps
			   3 = 8-15Gbps (2nd tuple default)
			   4 = 2.5-4Gbps
			   5 = 4-5Gbps
			   6 = 5-6Gbps
			   7 = 6-16Gbps (3rd tuple default)

NOTE: PHY override parameters are board specific setting.

Example:
		phy1: phy@1f21a000 {
			compatible = "apm,xgene-phy";
			reg = <0x0 0x1f21a000 0x0 0x100>;
			#phy-cells = <1>;
		};

		phy2: phy@1f22a000 {
			compatible = "apm,xgene-phy";
			reg = <0x0 0x1f22a000 0x0 0x100>;
			#phy-cells = <1>;
		};

		phy3: phy@1f23a000 {
			compatible = "apm,xgene-phy";
			reg = <0x0 0x1f23a000 0x0 0x100>;
			#phy-cells = <1>;
		};