| // SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| /* |
| * Copyright (c) 2019 Fuzhou Rockchip Electronics Co., Ltd. |
| */ |
| |
| #include <dt-bindings/clock/rockchip,rv1126-cru.h> |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| #include <dt-bindings/interrupt-controller/irq.h> |
| #include <dt-bindings/pinctrl/rockchip.h> |
| #include <dt-bindings/power/rockchip,rv1126-power.h> |
| #include <dt-bindings/soc/rockchip,boot-mode.h> |
| |
| / { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| compatible = "rockchip,rv1126"; |
| |
| interrupt-parent = <&gic>; |
| |
| aliases { |
| i2c0 = &i2c0; |
| i2c2 = &i2c2; |
| serial0 = &uart0; |
| serial1 = &uart1; |
| serial2 = &uart2; |
| serial3 = &uart3; |
| serial4 = &uart4; |
| serial5 = &uart5; |
| }; |
| |
| cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| cpu0: cpu@f00 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a7"; |
| reg = <0xf00>; |
| enable-method = "psci"; |
| clocks = <&cru ARMCLK>; |
| }; |
| |
| cpu1: cpu@f01 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a7"; |
| reg = <0xf01>; |
| enable-method = "psci"; |
| clocks = <&cru ARMCLK>; |
| }; |
| |
| cpu2: cpu@f02 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a7"; |
| reg = <0xf02>; |
| enable-method = "psci"; |
| clocks = <&cru ARMCLK>; |
| }; |
| |
| cpu3: cpu@f03 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a7"; |
| reg = <0xf03>; |
| enable-method = "psci"; |
| clocks = <&cru ARMCLK>; |
| }; |
| }; |
| |
| arm-pmu { |
| compatible = "arm,cortex-a7-pmu"; |
| interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>; |
| }; |
| |
| psci { |
| compatible = "arm,psci-1.0"; |
| method = "smc"; |
| }; |
| |
| timer { |
| compatible = "arm,armv7-timer"; |
| interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>, |
| <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>, |
| <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>, |
| <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; |
| clock-frequency = <24000000>; |
| }; |
| |
| display_subsystem { |
| compatible = "rockchip,display-subsystem"; |
| ports = <&vop_out>; |
| }; |
| |
| xin24m: oscillator { |
| compatible = "fixed-clock"; |
| clock-frequency = <24000000>; |
| clock-output-names = "xin24m"; |
| #clock-cells = <0>; |
| }; |
| |
| grf: syscon@fe000000 { |
| compatible = "rockchip,rv1126-grf", "syscon", "simple-mfd"; |
| reg = <0xfe000000 0x20000>; |
| }; |
| |
| pmugrf: syscon@fe020000 { |
| compatible = "rockchip,rv1126-pmugrf", "syscon", "simple-mfd"; |
| reg = <0xfe020000 0x1000>; |
| |
| pmu_io_domains: io-domains { |
| compatible = "rockchip,rv1126-pmu-io-voltage-domain"; |
| status = "disabled"; |
| }; |
| }; |
| |
| qos_emmc: qos@fe860000 { |
| compatible = "rockchip,rv1126-qos", "syscon"; |
| reg = <0xfe860000 0x20>; |
| }; |
| |
| qos_nandc: qos@fe860080 { |
| compatible = "rockchip,rv1126-qos", "syscon"; |
| reg = <0xfe860080 0x20>; |
| }; |
| |
| qos_sfc: qos@fe860200 { |
| compatible = "rockchip,rv1126-qos", "syscon"; |
| reg = <0xfe860200 0x20>; |
| }; |
| |
| qos_sdio: qos@fe86c000 { |
| compatible = "rockchip,rv1126-qos", "syscon"; |
| reg = <0xfe86c000 0x20>; |
| }; |
| |
| qos_iep: qos@fe8a0000 { |
| compatible = "rockchip,rv1126-qos", "syscon"; |
| reg = <0xfe8a0000 0x20>; |
| }; |
| |
| qos_rga_rd: qos@fe8a0080 { |
| compatible = "rockchip,rv1126-qos", "syscon"; |
| reg = <0xfe8a0080 0x20>; |
| }; |
| |
| qos_rga_wr: qos@fe8a0100 { |
| compatible = "rockchip,rv1126-qos", "syscon"; |
| reg = <0xfe8a0100 0x20>; |
| }; |
| |
| qos_vop: qos@fe8a0180 { |
| compatible = "rockchip,rv1126-qos", "syscon"; |
| reg = <0xfe8a0180 0x20>; |
| }; |
| |
| gic: interrupt-controller@feff0000 { |
| compatible = "arm,gic-400"; |
| interrupt-controller; |
| #interrupt-cells = <3>; |
| #address-cells = <0>; |
| |
| reg = <0xfeff1000 0x1000>, |
| <0xfeff2000 0x2000>, |
| <0xfeff4000 0x2000>, |
| <0xfeff6000 0x2000>; |
| interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; |
| }; |
| |
| pmu: power-management@ff3e0000 { |
| compatible = "rockchip,rv1126-pmu", "syscon", "simple-mfd"; |
| reg = <0xff3e0000 0x1000>; |
| |
| power: power-controller { |
| compatible = "rockchip,rv1126-power-controller"; |
| #power-domain-cells = <1>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| power-domain@RV1126_PD_NVM { |
| reg = <RV1126_PD_NVM>; |
| clocks = <&cru HCLK_EMMC>, |
| <&cru CLK_EMMC>, |
| <&cru HCLK_NANDC>, |
| <&cru CLK_NANDC>, |
| <&cru HCLK_SFC>, |
| <&cru HCLK_SFCXIP>, |
| <&cru SCLK_SFC>; |
| pm_qos = <&qos_emmc>, |
| <&qos_nandc>, |
| <&qos_sfc>; |
| #power-domain-cells = <0>; |
| }; |
| |
| power-domain@RV1126_PD_SDIO { |
| reg = <RV1126_PD_SDIO>; |
| clocks = <&cru HCLK_SDIO>, |
| <&cru CLK_SDIO>; |
| pm_qos = <&qos_sdio>; |
| #power-domain-cells = <0>; |
| }; |
| |
| power-domain@RV1126_PD_VO { |
| reg = <RV1126_PD_VO>; |
| clocks = <&cru ACLK_RGA>, |
| <&cru HCLK_RGA>, |
| <&cru CLK_RGA_CORE>, |
| <&cru ACLK_VOP>, |
| <&cru HCLK_VOP>, |
| <&cru DCLK_VOP>, |
| <&cru PCLK_DSIHOST>, |
| <&cru ACLK_IEP>, |
| <&cru HCLK_IEP>, |
| <&cru CLK_IEP_CORE>; |
| pm_qos = <&qos_rga_rd>, |
| <&qos_rga_wr>, |
| <&qos_vop>, |
| <&qos_iep>; |
| #power-domain-cells = <0>; |
| }; |
| }; |
| }; |
| |
| i2c0: i2c@ff3f0000 { |
| compatible = "rockchip,rv1126-i2c", "rockchip,rk3399-i2c"; |
| reg = <0xff3f0000 0x1000>; |
| interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; |
| rockchip,grf = <&pmugrf>; |
| clocks = <&pmucru CLK_I2C0>, <&pmucru PCLK_I2C0>; |
| clock-names = "i2c", "pclk"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c0_xfer>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| i2c2: i2c@ff400000 { |
| compatible = "rockchip,rv1126-i2c", "rockchip,rk3399-i2c"; |
| reg = <0xff400000 0x1000>; |
| interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; |
| rockchip,grf = <&pmugrf>; |
| clocks = <&pmucru CLK_I2C2>, <&pmucru PCLK_I2C2>; |
| clock-names = "i2c", "pclk"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c2_xfer>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| uart1: serial@ff410000 { |
| compatible = "rockchip,rv1126-uart", "snps,dw-apb-uart"; |
| reg = <0xff410000 0x100>; |
| interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; |
| clock-frequency = <24000000>; |
| clocks = <&pmucru SCLK_UART1>, <&pmucru PCLK_UART1>; |
| clock-names = "baudclk", "apb_pclk"; |
| dmas = <&dmac 7>, <&dmac 6>; |
| dma-names = "tx", "rx"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart1m0_xfer>; |
| reg-shift = <2>; |
| reg-io-width = <4>; |
| status = "disabled"; |
| }; |
| |
| pwm2: pwm@ff430020 { |
| compatible = "rockchip,rv1126-pwm", "rockchip,rk3328-pwm"; |
| reg = <0xff430020 0x10>; |
| clock-names = "pwm", "pclk"; |
| clocks = <&pmucru CLK_PWM0>, <&pmucru PCLK_PWM0>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pwm2m0_pins>; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| |
| pmucru: clock-controller@ff480000 { |
| compatible = "rockchip,rv1126-pmucru"; |
| reg = <0xff480000 0x1000>; |
| rockchip,grf = <&grf>; |
| #clock-cells = <1>; |
| #reset-cells = <1>; |
| }; |
| |
| cru: clock-controller@ff490000 { |
| compatible = "rockchip,rv1126-cru"; |
| reg = <0xff490000 0x1000>; |
| clocks = <&xin24m>; |
| clock-names = "xin24m"; |
| rockchip,grf = <&grf>; |
| #clock-cells = <1>; |
| #reset-cells = <1>; |
| }; |
| |
| dmac: dma-controller@ff4e0000 { |
| compatible = "arm,pl330", "arm,primecell"; |
| reg = <0xff4e0000 0x4000>; |
| interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>; |
| #dma-cells = <1>; |
| arm,pl330-periph-burst; |
| clocks = <&cru ACLK_DMAC>; |
| clock-names = "apb_pclk"; |
| }; |
| |
| pwm11: pwm@ff550030 { |
| compatible = "rockchip,rv1126-pwm", "rockchip,rk3328-pwm"; |
| reg = <0xff550030 0x10>; |
| clock-names = "pwm", "pclk"; |
| clocks = <&cru CLK_PWM2>, <&cru PCLK_PWM2>; |
| pinctrl-0 = <&pwm11m0_pins>; |
| pinctrl-names = "default"; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| |
| uart0: serial@ff560000 { |
| compatible = "rockchip,rv1126-uart", "snps,dw-apb-uart"; |
| reg = <0xff560000 0x100>; |
| interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; |
| clock-frequency = <24000000>; |
| clocks = <&cru SCLK_UART0>, <&cru PCLK_UART0>; |
| clock-names = "baudclk", "apb_pclk"; |
| dmas = <&dmac 5>, <&dmac 4>; |
| dma-names = "tx", "rx"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart0_xfer>; |
| reg-shift = <2>; |
| reg-io-width = <4>; |
| status = "disabled"; |
| }; |
| |
| uart2: serial@ff570000 { |
| compatible = "rockchip,rv1126-uart", "snps,dw-apb-uart"; |
| reg = <0xff570000 0x100>; |
| interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; |
| clock-frequency = <24000000>; |
| clocks = <&cru SCLK_UART2>, <&cru PCLK_UART2>; |
| clock-names = "baudclk", "apb_pclk"; |
| dmas = <&dmac 9>, <&dmac 8>; |
| dma-names = "tx", "rx"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart2m1_xfer>; |
| reg-shift = <2>; |
| reg-io-width = <4>; |
| status = "disabled"; |
| }; |
| |
| uart3: serial@ff580000 { |
| compatible = "rockchip,rv1126-uart", "snps,dw-apb-uart"; |
| reg = <0xff580000 0x100>; |
| interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; |
| clock-frequency = <24000000>; |
| clocks = <&cru SCLK_UART3>, <&cru PCLK_UART3>; |
| clock-names = "baudclk", "apb_pclk"; |
| dmas = <&dmac 11>, <&dmac 10>; |
| dma-names = "tx", "rx"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart3m0_xfer>; |
| reg-shift = <2>; |
| reg-io-width = <4>; |
| status = "disabled"; |
| }; |
| |
| uart4: serial@ff590000 { |
| compatible = "rockchip,rv1126-uart", "snps,dw-apb-uart"; |
| reg = <0xff590000 0x100>; |
| interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>; |
| clock-frequency = <24000000>; |
| clocks = <&cru SCLK_UART4>, <&cru PCLK_UART4>; |
| clock-names = "baudclk", "apb_pclk"; |
| dmas = <&dmac 13>, <&dmac 12>; |
| dma-names = "tx", "rx"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart4m0_xfer>; |
| reg-shift = <2>; |
| reg-io-width = <4>; |
| status = "disabled"; |
| }; |
| |
| uart5: serial@ff5a0000 { |
| compatible = "rockchip,rv1126-uart", "snps,dw-apb-uart"; |
| reg = <0xff5a0000 0x100>; |
| interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>; |
| clock-frequency = <24000000>; |
| clocks = <&cru SCLK_UART5>, <&cru PCLK_UART5>; |
| clock-names = "baudclk", "apb_pclk"; |
| dmas = <&dmac 15>, <&dmac 14>; |
| dma-names = "tx", "rx"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart5m0_xfer>; |
| reg-shift = <2>; |
| reg-io-width = <4>; |
| status = "disabled"; |
| }; |
| |
| saradc: adc@ff5e0000 { |
| compatible = "rockchip,rv1126-saradc", "rockchip,rk3399-saradc"; |
| reg = <0xff5e0000 0x100>; |
| interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; |
| #io-channel-cells = <1>; |
| clocks = <&cru CLK_SARADC>, <&cru PCLK_SARADC>; |
| clock-names = "saradc", "apb_pclk"; |
| resets = <&cru SRST_SARADC_P>; |
| reset-names = "saradc-apb"; |
| status = "disabled"; |
| }; |
| |
| timer0: timer@ff660000 { |
| compatible = "rockchip,rv1126-timer", "rockchip,rk3288-timer"; |
| reg = <0xff660000 0x20>; |
| interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru PCLK_TIMER>, <&cru CLK_TIMER0>; |
| clock-names = "pclk", "timer"; |
| }; |
| |
| vop: vop@ffb00000 { |
| compatible = "rockchip,rv1126-vop"; |
| reg = <0xffb00000 0x200>, <0xffb00a00 0x400>; |
| interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>; |
| clock-names = "aclk_vop", "dclk_vop", "hclk_vop"; |
| clocks = <&cru ACLK_VOP>, <&cru DCLK_VOP>, <&cru HCLK_VOP>; |
| reset-names = "axi", "ahb", "dclk"; |
| resets = <&cru SRST_VOP_A>, <&cru SRST_VOP_H>, <&cru SRST_VOP_D>; |
| iommus = <&vop_mmu>; |
| power-domains = <&power RV1126_PD_VO>; |
| status = "disabled"; |
| |
| vop_out: port { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| vop_out_rgb: endpoint@0 { |
| reg = <0>; |
| }; |
| |
| vop_out_dsi: endpoint@1 { |
| reg = <1>; |
| }; |
| }; |
| }; |
| |
| vop_mmu: iommu@ffb00f00 { |
| compatible = "rockchip,iommu"; |
| reg = <0xffb00f00 0x100>; |
| interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>; |
| clock-names = "aclk", "iface"; |
| clocks = <&cru ACLK_VOP>, <&cru HCLK_VOP>; |
| #iommu-cells = <0>; |
| power-domains = <&power RV1126_PD_VO>; |
| status = "disabled"; |
| }; |
| |
| gmac: ethernet@ffc40000 { |
| compatible = "rockchip,rv1126-gmac", "snps,dwmac-4.20a"; |
| reg = <0xffc40000 0x4000>; |
| interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "macirq", "eth_wake_irq"; |
| rockchip,grf = <&grf>; |
| clocks = <&cru CLK_GMAC_SRC>, <&cru CLK_GMAC_TX_RX>, |
| <&cru CLK_GMAC_TX_RX>, <&cru CLK_GMAC_REF>, |
| <&cru ACLK_GMAC>, <&cru PCLK_GMAC>, |
| <&cru CLK_GMAC_TX_RX>, <&cru CLK_GMAC_PTPREF>; |
| clock-names = "stmmaceth", "mac_clk_rx", |
| "mac_clk_tx", "clk_mac_ref", |
| "aclk_mac", "pclk_mac", |
| "clk_mac_speed", "ptp_ref"; |
| resets = <&cru SRST_GMAC_A>; |
| reset-names = "stmmaceth"; |
| |
| snps,mixed-burst; |
| snps,tso; |
| |
| snps,axi-config = <&stmmac_axi_setup>; |
| snps,mtl-rx-config = <&mtl_rx_setup>; |
| snps,mtl-tx-config = <&mtl_tx_setup>; |
| status = "disabled"; |
| |
| mdio: mdio { |
| compatible = "snps,dwmac-mdio"; |
| #address-cells = <0x1>; |
| #size-cells = <0x0>; |
| }; |
| |
| stmmac_axi_setup: stmmac-axi-config { |
| snps,wr_osr_lmt = <4>; |
| snps,rd_osr_lmt = <8>; |
| snps,blen = <0 0 0 0 16 8 4>; |
| }; |
| |
| mtl_rx_setup: rx-queues-config { |
| snps,rx-queues-to-use = <1>; |
| queue0 {}; |
| }; |
| |
| mtl_tx_setup: tx-queues-config { |
| snps,tx-queues-to-use = <1>; |
| queue0 {}; |
| }; |
| }; |
| |
| emmc: mmc@ffc50000 { |
| compatible = "rockchip,rv1126-dw-mshc", "rockchip,rk3288-dw-mshc"; |
| reg = <0xffc50000 0x4000>; |
| interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru HCLK_EMMC>, <&cru CLK_EMMC>, |
| <&cru SCLK_EMMC_DRV>, <&cru SCLK_EMMC_SAMPLE>; |
| clock-names = "biu", "ciu", "ciu-drive", "ciu-sample"; |
| fifo-depth = <0x100>; |
| max-frequency = <200000000>; |
| power-domains = <&power RV1126_PD_NVM>; |
| status = "disabled"; |
| }; |
| |
| sdmmc: mmc@ffc60000 { |
| compatible = "rockchip,rv1126-dw-mshc", "rockchip,rk3288-dw-mshc"; |
| reg = <0xffc60000 0x4000>; |
| interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru HCLK_SDMMC>, <&cru CLK_SDMMC>, |
| <&cru SCLK_SDMMC_DRV>, <&cru SCLK_SDMMC_SAMPLE>; |
| clock-names = "biu", "ciu", "ciu-drive", "ciu-sample"; |
| fifo-depth = <0x100>; |
| max-frequency = <200000000>; |
| status = "disabled"; |
| }; |
| |
| sdio: mmc@ffc70000 { |
| compatible = "rockchip,rv1126-dw-mshc", "rockchip,rk3288-dw-mshc"; |
| reg = <0xffc70000 0x4000>; |
| interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru HCLK_SDIO>, <&cru CLK_SDIO>, |
| <&cru SCLK_SDIO_DRV>, <&cru SCLK_SDIO_SAMPLE>; |
| clock-names = "biu", "ciu", "ciu-drive", "ciu-sample"; |
| fifo-depth = <0x100>; |
| max-frequency = <200000000>; |
| power-domains = <&power RV1126_PD_SDIO>; |
| status = "disabled"; |
| }; |
| |
| sfc: spi@ffc90000 { |
| compatible = "rockchip,sfc"; |
| reg = <0xffc90000 0x4000>; |
| interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>; |
| assigned-clocks = <&cru SCLK_SFC>; |
| assigned-clock-rates = <80000000>; |
| clock-names = "clk_sfc", "hclk_sfc"; |
| clocks = <&cru SCLK_SFC>, <&cru HCLK_SFC>; |
| power-domains = <&power RV1126_PD_NVM>; |
| status = "disabled"; |
| }; |
| |
| pinctrl: pinctrl { |
| compatible = "rockchip,rv1126-pinctrl"; |
| rockchip,grf = <&grf>; |
| rockchip,pmu = <&pmugrf>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| gpio0: gpio@ff460000 { |
| compatible = "rockchip,gpio-bank"; |
| reg = <0xff460000 0x100>; |
| interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&pmucru PCLK_GPIO0>, <&pmucru DBCLK_GPIO0>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio1: gpio@ff620000 { |
| compatible = "rockchip,gpio-bank"; |
| reg = <0xff620000 0x100>; |
| interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru PCLK_GPIO1>, <&cru DBCLK_GPIO1>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio2: gpio@ff630000 { |
| compatible = "rockchip,gpio-bank"; |
| reg = <0xff630000 0x100>; |
| interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru PCLK_GPIO2>, <&cru DBCLK_GPIO2>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio3: gpio@ff640000 { |
| compatible = "rockchip,gpio-bank"; |
| reg = <0xff640000 0x100>; |
| interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru PCLK_GPIO3>, <&cru DBCLK_GPIO3>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| gpio4: gpio@ff650000 { |
| compatible = "rockchip,gpio-bank"; |
| reg = <0xff650000 0x100>; |
| interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&cru PCLK_GPIO4>, <&cru DBCLK_GPIO4>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| }; |
| |
| #include "rv1126-pinctrl.dtsi" |
