| // SPDX-License-Identifier: GPL-2.0-only |
| /* |
| * Ilitek ILI9341 TFT LCD drm_panel driver. |
| * |
| * This panel can be configured to support: |
| * - 16-bit parallel RGB interface |
| * - 18-bit parallel RGB interface |
| * - 4-line serial spi interface |
| * |
| * Copyright (C) 2021 Dillon Min <dillon.minfei@gmail.com> |
| * |
| * For dbi+dpi part: |
| * Derived from drivers/drm/gpu/panel/panel-ilitek-ili9322.c |
| * the reuse of DBI abstraction part referred from Linus's patch |
| * "drm/panel: s6e63m0: Switch to DBI abstraction for SPI" |
| * |
| * For only-dbi part, copy from David's code (drm/tiny/ili9341.c) |
| * Copyright 2018 David Lechner <david@lechnology.com> |
| */ |
| |
| #include <linux/backlight.h> |
| #include <linux/bitops.h> |
| #include <linux/delay.h> |
| #include <linux/gpio/consumer.h> |
| #include <linux/module.h> |
| #include <linux/of.h> |
| #include <linux/regulator/consumer.h> |
| #include <linux/spi/spi.h> |
| |
| #include <video/mipi_display.h> |
| |
| #include <drm/drm_atomic_helper.h> |
| #include <drm/drm_drv.h> |
| #include <drm/drm_fbdev_generic.h> |
| #include <drm/drm_gem_atomic_helper.h> |
| #include <drm/drm_gem_dma_helper.h> |
| #include <drm/drm_gem_framebuffer_helper.h> |
| #include <drm/drm_mipi_dbi.h> |
| #include <drm/drm_modes.h> |
| #include <drm/drm_panel.h> |
| #include <drm/drm_print.h> |
| |
| #define ILI9341_RGB_INTERFACE 0xb0 /* RGB Interface Signal Control */ |
| #define ILI9341_FRC 0xb1 /* Frame Rate Control register */ |
| #define ILI9341_DFC 0xb6 /* Display Function Control register */ |
| #define ILI9341_POWER1 0xc0 /* Power Control 1 register */ |
| #define ILI9341_POWER2 0xc1 /* Power Control 2 register */ |
| #define ILI9341_VCOM1 0xc5 /* VCOM Control 1 register */ |
| #define ILI9341_VCOM2 0xc7 /* VCOM Control 2 register */ |
| #define ILI9341_POWERA 0xcb /* Power control A register */ |
| #define ILI9341_POWERB 0xcf /* Power control B register */ |
| #define ILI9341_PGAMMA 0xe0 /* Positive Gamma Correction register */ |
| #define ILI9341_NGAMMA 0xe1 /* Negative Gamma Correction register */ |
| #define ILI9341_DTCA 0xe8 /* Driver timing control A */ |
| #define ILI9341_DTCB 0xea /* Driver timing control B */ |
| #define ILI9341_POWER_SEQ 0xed /* Power on sequence register */ |
| #define ILI9341_3GAMMA_EN 0xf2 /* 3 Gamma enable register */ |
| #define ILI9341_INTERFACE 0xf6 /* Interface control register */ |
| #define ILI9341_PRC 0xf7 /* Pump ratio control register */ |
| #define ILI9341_ETMOD 0xb7 /* Entry mode set */ |
| |
| #define ILI9341_MADCTL_BGR BIT(3) |
| #define ILI9341_MADCTL_MV BIT(5) |
| #define ILI9341_MADCTL_MX BIT(6) |
| #define ILI9341_MADCTL_MY BIT(7) |
| |
| #define ILI9341_POWER_B_LEN 3 |
| #define ILI9341_POWER_SEQ_LEN 4 |
| #define ILI9341_DTCA_LEN 3 |
| #define ILI9341_DTCB_LEN 2 |
| #define ILI9341_POWER_A_LEN 5 |
| #define ILI9341_DFC_1_LEN 2 |
| #define ILI9341_FRC_LEN 2 |
| #define ILI9341_VCOM_1_LEN 2 |
| #define ILI9341_DFC_2_LEN 4 |
| #define ILI9341_COLUMN_ADDR_LEN 4 |
| #define ILI9341_PAGE_ADDR_LEN 4 |
| #define ILI9341_INTERFACE_LEN 3 |
| #define ILI9341_PGAMMA_LEN 15 |
| #define ILI9341_NGAMMA_LEN 15 |
| #define ILI9341_CA_LEN 3 |
| |
| #define ILI9341_PIXEL_DPI_16_BITS (BIT(6) | BIT(4)) |
| #define ILI9341_PIXEL_DPI_18_BITS (BIT(6) | BIT(5)) |
| #define ILI9341_GAMMA_CURVE_1 BIT(0) |
| #define ILI9341_IF_WE_MODE BIT(0) |
| #define ILI9341_IF_BIG_ENDIAN 0x00 |
| #define ILI9341_IF_DM_RGB BIT(2) |
| #define ILI9341_IF_DM_INTERNAL 0x00 |
| #define ILI9341_IF_DM_VSYNC BIT(3) |
| #define ILI9341_IF_RM_RGB BIT(1) |
| #define ILI9341_IF_RIM_RGB 0x00 |
| |
| #define ILI9341_COLUMN_ADDR 0x00ef |
| #define ILI9341_PAGE_ADDR 0x013f |
| |
| #define ILI9341_RGB_EPL BIT(0) |
| #define ILI9341_RGB_DPL BIT(1) |
| #define ILI9341_RGB_HSPL BIT(2) |
| #define ILI9341_RGB_VSPL BIT(3) |
| #define ILI9341_RGB_DE_MODE BIT(6) |
| #define ILI9341_RGB_DISP_PATH_MEM BIT(7) |
| |
| #define ILI9341_DBI_VCOMH_4P6V 0x23 |
| #define ILI9341_DBI_PWR_2_DEFAULT 0x10 |
| #define ILI9341_DBI_PRC_NORMAL 0x20 |
| #define ILI9341_DBI_VCOM_1_VMH_4P25V 0x3e |
| #define ILI9341_DBI_VCOM_1_VML_1P5V 0x28 |
| #define ILI9341_DBI_VCOM_2_DEC_58 0x86 |
| #define ILI9341_DBI_FRC_DIVA 0x00 |
| #define ILI9341_DBI_FRC_RTNA 0x1b |
| #define ILI9341_DBI_EMS_GAS BIT(0) |
| #define ILI9341_DBI_EMS_DTS BIT(1) |
| #define ILI9341_DBI_EMS_GON BIT(2) |
| |
| /* struct ili9341_config - the system specific ILI9341 configuration */ |
| struct ili9341_config { |
| u32 max_spi_speed; |
| /* mode: the drm display mode */ |
| const struct drm_display_mode mode; |
| /* ca: TODO: need comments for this register */ |
| u8 ca[ILI9341_CA_LEN]; |
| /* power_b: TODO: need comments for this register */ |
| u8 power_b[ILI9341_POWER_B_LEN]; |
| /* power_seq: TODO: need comments for this register */ |
| u8 power_seq[ILI9341_POWER_SEQ_LEN]; |
| /* dtca: TODO: need comments for this register */ |
| u8 dtca[ILI9341_DTCA_LEN]; |
| /* dtcb: TODO: need comments for this register */ |
| u8 dtcb[ILI9341_DTCB_LEN]; |
| /* power_a: TODO: need comments for this register */ |
| u8 power_a[ILI9341_POWER_A_LEN]; |
| /* frc: Frame Rate Control (In Normal Mode/Full Colors) (B1h) */ |
| u8 frc[ILI9341_FRC_LEN]; |
| /* prc: TODO: need comments for this register */ |
| u8 prc; |
| /* dfc_1: B6h DISCTRL (Display Function Control) */ |
| u8 dfc_1[ILI9341_DFC_1_LEN]; |
| /* power_1: Power Control 1 (C0h) */ |
| u8 power_1; |
| /* power_2: Power Control 2 (C1h) */ |
| u8 power_2; |
| /* vcom_1: VCOM Control 1(C5h) */ |
| u8 vcom_1[ILI9341_VCOM_1_LEN]; |
| /* vcom_2: VCOM Control 2(C7h) */ |
| u8 vcom_2; |
| /* address_mode: Memory Access Control (36h) */ |
| u8 address_mode; |
| /* g3amma_en: TODO: need comments for this register */ |
| u8 g3amma_en; |
| /* rgb_interface: RGB Interface Signal Control (B0h) */ |
| u8 rgb_interface; |
| /* dfc_2: refer to dfc_1 */ |
| u8 dfc_2[ILI9341_DFC_2_LEN]; |
| /* column_addr: Column Address Set (2Ah) */ |
| u8 column_addr[ILI9341_COLUMN_ADDR_LEN]; |
| /* page_addr: Page Address Set (2Bh) */ |
| u8 page_addr[ILI9341_PAGE_ADDR_LEN]; |
| /* interface: Interface Control (F6h) */ |
| u8 interface[ILI9341_INTERFACE_LEN]; |
| /* |
| * pixel_format: This command sets the pixel format for the RGB |
| * image data used by |
| */ |
| u8 pixel_format; |
| /* |
| * gamma_curve: This command is used to select the desired Gamma |
| * curve for the |
| */ |
| u8 gamma_curve; |
| /* pgamma: Positive Gamma Correction (E0h) */ |
| u8 pgamma[ILI9341_PGAMMA_LEN]; |
| /* ngamma: Negative Gamma Correction (E1h) */ |
| u8 ngamma[ILI9341_NGAMMA_LEN]; |
| }; |
| |
| struct ili9341 { |
| struct device *dev; |
| const struct ili9341_config *conf; |
| struct drm_panel panel; |
| struct gpio_desc *reset_gpio; |
| struct gpio_desc *dc_gpio; |
| struct mipi_dbi *dbi; |
| u32 max_spi_speed; |
| struct regulator_bulk_data supplies[3]; |
| }; |
| |
| /* |
| * The Stm32f429-disco board has a panel ili9341 connected to ltdc controller |
| */ |
| static const struct ili9341_config ili9341_stm32f429_disco_data = { |
| .max_spi_speed = 10000000, |
| .mode = { |
| .clock = 6100, |
| .hdisplay = 240, |
| .hsync_start = 240 + 10,/* hfp 10 */ |
| .hsync_end = 240 + 10 + 10,/* hsync 10 */ |
| .htotal = 240 + 10 + 10 + 20,/* hbp 20 */ |
| .vdisplay = 320, |
| .vsync_start = 320 + 4,/* vfp 4 */ |
| .vsync_end = 320 + 4 + 2,/* vsync 2 */ |
| .vtotal = 320 + 4 + 2 + 2,/* vbp 2 */ |
| .flags = 0, |
| .width_mm = 65, |
| .height_mm = 50, |
| .type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED, |
| }, |
| .ca = {0xc3, 0x08, 0x50}, |
| .power_b = {0x00, 0xc1, 0x30}, |
| .power_seq = {0x64, 0x03, 0x12, 0x81}, |
| .dtca = {0x85, 0x00, 0x78}, |
| .power_a = {0x39, 0x2c, 0x00, 0x34, 0x02}, |
| .prc = 0x20, |
| .dtcb = {0x00, 0x00}, |
| /* 0x00 fosc, 0x1b 70hz */ |
| .frc = {0x00, 0x1b}, |
| /* |
| * 0x0a Interval scan, AGND AGND AGND AGND |
| * 0xa2 Normally white, G1 -> G320, S720 -> S1, |
| * Scan Cycle 5 frames,85ms |
| */ |
| .dfc_1 = {0x0a, 0xa2}, |
| /* 0x10 3.65v */ |
| .power_1 = 0x10, |
| /* 0x10 AVDD=vci*2, VGH=vci*7, VGL=-vci*4 */ |
| .power_2 = 0x10, |
| /* 0x45 VCOMH 4.425v, 0x15 VCOML -1.975*/ |
| .vcom_1 = {0x45, 0x15}, |
| /* 0x90 offset voltage, VMH-48, VML-48 */ |
| .vcom_2 = 0x90, |
| /* |
| * 0xc8 Row Address Order, Column Address Order |
| * BGR 1 |
| */ |
| .address_mode = 0xc8, |
| .g3amma_en = 0x00, |
| /* |
| * 0xc2 |
| * Display Data Path: Memory |
| * RGB: DE mode |
| * DOTCLK polarity set (data fetched at the falling time) |
| */ |
| .rgb_interface = ILI9341_RGB_DISP_PATH_MEM | |
| ILI9341_RGB_DE_MODE | |
| ILI9341_RGB_DPL, |
| /* |
| * 0x0a |
| * Gate outputs in non-display area: Interval scan |
| * Determine source/VCOM output in a non-display area in the partial |
| * display mode: AGND AGND AGND AGND |
| * |
| * 0xa7 |
| * Scan Cycle: 15 frames |
| * fFLM = 60Hz: 255ms |
| * Liquid crystal type: Normally white |
| * Gate Output Scan Direction: G1 -> G320 |
| * Source Output Scan Direction: S720 -> S1 |
| * |
| * 0x27 |
| * LCD Driver Line: 320 lines |
| * |
| * 0x04 |
| * PCDIV: 4 |
| */ |
| .dfc_2 = {0x0a, 0xa7, 0x27, 0x04}, |
| /* column address: 240 */ |
| .column_addr = {0x00, 0x00, (ILI9341_COLUMN_ADDR >> 4) & 0xff, |
| ILI9341_COLUMN_ADDR & 0xff}, |
| /* page address: 320 */ |
| .page_addr = {0x00, 0x00, (ILI9341_PAGE_ADDR >> 4) & 0xff, |
| ILI9341_PAGE_ADDR & 0xff}, |
| /* |
| * Memory write control: When the transfer number of data exceeds |
| * (EC-SC+1)*(EP-SP+1), the column and page number will be |
| * reset, and the exceeding data will be written into the following |
| * column and page. |
| * Display Operation Mode: RGB Interface Mode |
| * Interface for RAM Access: RGB interface |
| * 16- bit RGB interface (1 transfer/pixel) |
| */ |
| .interface = {ILI9341_IF_WE_MODE, 0x00, |
| ILI9341_IF_DM_RGB | ILI9341_IF_RM_RGB}, |
| /* DPI: 16 bits / pixel */ |
| .pixel_format = ILI9341_PIXEL_DPI_16_BITS, |
| /* Curve Selected: Gamma curve 1 (G2.2) */ |
| .gamma_curve = ILI9341_GAMMA_CURVE_1, |
| .pgamma = {0x0f, 0x29, 0x24, 0x0c, 0x0e, |
| 0x09, 0x4e, 0x78, 0x3c, 0x09, |
| 0x13, 0x05, 0x17, 0x11, 0x00}, |
| .ngamma = {0x00, 0x16, 0x1b, 0x04, 0x11, |
| 0x07, 0x31, 0x33, 0x42, 0x05, |
| 0x0c, 0x0a, 0x28, 0x2f, 0x0f}, |
| }; |
| |
| static inline struct ili9341 *panel_to_ili9341(struct drm_panel *panel) |
| { |
| return container_of(panel, struct ili9341, panel); |
| } |
| |
| static void ili9341_dpi_init(struct ili9341 *ili) |
| { |
| struct device *dev = (&ili->panel)->dev; |
| struct mipi_dbi *dbi = ili->dbi; |
| struct ili9341_config *cfg = (struct ili9341_config *)ili->conf; |
| |
| /* Power Control */ |
| mipi_dbi_command_stackbuf(dbi, 0xca, cfg->ca, ILI9341_CA_LEN); |
| mipi_dbi_command_stackbuf(dbi, ILI9341_POWERB, cfg->power_b, |
| ILI9341_POWER_B_LEN); |
| mipi_dbi_command_stackbuf(dbi, ILI9341_POWER_SEQ, cfg->power_seq, |
| ILI9341_POWER_SEQ_LEN); |
| mipi_dbi_command_stackbuf(dbi, ILI9341_DTCA, cfg->dtca, |
| ILI9341_DTCA_LEN); |
| mipi_dbi_command_stackbuf(dbi, ILI9341_POWERA, cfg->power_a, |
| ILI9341_POWER_A_LEN); |
| mipi_dbi_command(ili->dbi, ILI9341_PRC, cfg->prc); |
| mipi_dbi_command_stackbuf(dbi, ILI9341_DTCB, cfg->dtcb, |
| ILI9341_DTCB_LEN); |
| mipi_dbi_command_stackbuf(dbi, ILI9341_FRC, cfg->frc, ILI9341_FRC_LEN); |
| mipi_dbi_command_stackbuf(dbi, ILI9341_DFC, cfg->dfc_1, |
| ILI9341_DFC_1_LEN); |
| mipi_dbi_command(dbi, ILI9341_POWER1, cfg->power_1); |
| mipi_dbi_command(dbi, ILI9341_POWER2, cfg->power_2); |
| |
| /* VCOM */ |
| mipi_dbi_command_stackbuf(dbi, ILI9341_VCOM1, cfg->vcom_1, |
| ILI9341_VCOM_1_LEN); |
| mipi_dbi_command(dbi, ILI9341_VCOM2, cfg->vcom_2); |
| mipi_dbi_command(dbi, MIPI_DCS_SET_ADDRESS_MODE, cfg->address_mode); |
| |
| /* Gamma */ |
| mipi_dbi_command(dbi, ILI9341_3GAMMA_EN, cfg->g3amma_en); |
| mipi_dbi_command(dbi, ILI9341_RGB_INTERFACE, cfg->rgb_interface); |
| mipi_dbi_command_stackbuf(dbi, ILI9341_DFC, cfg->dfc_2, |
| ILI9341_DFC_2_LEN); |
| |
| /* Colomn address set */ |
| mipi_dbi_command_stackbuf(dbi, MIPI_DCS_SET_COLUMN_ADDRESS, |
| cfg->column_addr, ILI9341_COLUMN_ADDR_LEN); |
| |
| /* Page address set */ |
| mipi_dbi_command_stackbuf(dbi, MIPI_DCS_SET_PAGE_ADDRESS, |
| cfg->page_addr, ILI9341_PAGE_ADDR_LEN); |
| mipi_dbi_command_stackbuf(dbi, ILI9341_INTERFACE, cfg->interface, |
| ILI9341_INTERFACE_LEN); |
| |
| /* Format */ |
| mipi_dbi_command(dbi, MIPI_DCS_SET_PIXEL_FORMAT, cfg->pixel_format); |
| mipi_dbi_command(dbi, MIPI_DCS_WRITE_MEMORY_START); |
| msleep(200); |
| mipi_dbi_command(dbi, MIPI_DCS_SET_GAMMA_CURVE, cfg->gamma_curve); |
| mipi_dbi_command_stackbuf(dbi, ILI9341_PGAMMA, cfg->pgamma, |
| ILI9341_PGAMMA_LEN); |
| mipi_dbi_command_stackbuf(dbi, ILI9341_NGAMMA, cfg->ngamma, |
| ILI9341_NGAMMA_LEN); |
| mipi_dbi_command(dbi, MIPI_DCS_EXIT_SLEEP_MODE); |
| msleep(200); |
| mipi_dbi_command(dbi, MIPI_DCS_SET_DISPLAY_ON); |
| mipi_dbi_command(dbi, MIPI_DCS_WRITE_MEMORY_START); |
| |
| dev_info(dev, "Initialized display rgb interface\n"); |
| } |
| |
| static int ili9341_dpi_power_on(struct ili9341 *ili) |
| { |
| struct device *dev = (&ili->panel)->dev; |
| int ret = 0; |
| |
| /* Assert RESET */ |
| gpiod_set_value(ili->reset_gpio, 1); |
| |
| /* Enable power */ |
| ret = regulator_bulk_enable(ARRAY_SIZE(ili->supplies), |
| ili->supplies); |
| if (ret < 0) { |
| dev_err(dev, "unable to enable vcc\n"); |
| return ret; |
| } |
| msleep(20); |
| |
| /* De-assert RESET */ |
| gpiod_set_value(ili->reset_gpio, 0); |
| msleep(20); |
| |
| return 0; |
| } |
| |
| static int ili9341_dpi_power_off(struct ili9341 *ili) |
| { |
| /* Assert RESET */ |
| gpiod_set_value(ili->reset_gpio, 1); |
| |
| /* Disable power */ |
| return regulator_bulk_disable(ARRAY_SIZE(ili->supplies), |
| ili->supplies); |
| } |
| |
| static int ili9341_dpi_disable(struct drm_panel *panel) |
| { |
| struct ili9341 *ili = panel_to_ili9341(panel); |
| |
| mipi_dbi_command(ili->dbi, MIPI_DCS_SET_DISPLAY_OFF); |
| return 0; |
| } |
| |
| static int ili9341_dpi_unprepare(struct drm_panel *panel) |
| { |
| struct ili9341 *ili = panel_to_ili9341(panel); |
| |
| return ili9341_dpi_power_off(ili); |
| } |
| |
| static int ili9341_dpi_prepare(struct drm_panel *panel) |
| { |
| struct ili9341 *ili = panel_to_ili9341(panel); |
| int ret; |
| |
| ret = ili9341_dpi_power_on(ili); |
| if (ret < 0) |
| return ret; |
| |
| ili9341_dpi_init(ili); |
| |
| return ret; |
| } |
| |
| static int ili9341_dpi_enable(struct drm_panel *panel) |
| { |
| struct ili9341 *ili = panel_to_ili9341(panel); |
| |
| mipi_dbi_command(ili->dbi, MIPI_DCS_SET_DISPLAY_ON); |
| return 0; |
| } |
| |
| static int ili9341_dpi_get_modes(struct drm_panel *panel, |
| struct drm_connector *connector) |
| { |
| struct ili9341 *ili = panel_to_ili9341(panel); |
| struct drm_device *drm = connector->dev; |
| struct drm_display_mode *mode; |
| struct drm_display_info *info; |
| |
| info = &connector->display_info; |
| info->width_mm = ili->conf->mode.width_mm; |
| info->height_mm = ili->conf->mode.height_mm; |
| |
| if (ili->conf->rgb_interface & ILI9341_RGB_DPL) |
| info->bus_flags |= DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE; |
| else |
| info->bus_flags |= DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE; |
| |
| if (ili->conf->rgb_interface & ILI9341_RGB_EPL) |
| info->bus_flags |= DRM_BUS_FLAG_DE_LOW; |
| else |
| info->bus_flags |= DRM_BUS_FLAG_DE_HIGH; |
| |
| mode = drm_mode_duplicate(drm, &ili->conf->mode); |
| if (!mode) { |
| drm_err(drm, "bad mode or failed to add mode\n"); |
| return -EINVAL; |
| } |
| drm_mode_set_name(mode); |
| |
| /* Set up the polarity */ |
| if (ili->conf->rgb_interface & ILI9341_RGB_HSPL) |
| mode->flags |= DRM_MODE_FLAG_PHSYNC; |
| else |
| mode->flags |= DRM_MODE_FLAG_NHSYNC; |
| |
| if (ili->conf->rgb_interface & ILI9341_RGB_VSPL) |
| mode->flags |= DRM_MODE_FLAG_PVSYNC; |
| else |
| mode->flags |= DRM_MODE_FLAG_NVSYNC; |
| |
| drm_mode_probed_add(connector, mode); |
| |
| return 1; /* Number of modes */ |
| } |
| |
| static const struct drm_panel_funcs ili9341_dpi_funcs = { |
| .disable = ili9341_dpi_disable, |
| .unprepare = ili9341_dpi_unprepare, |
| .prepare = ili9341_dpi_prepare, |
| .enable = ili9341_dpi_enable, |
| .get_modes = ili9341_dpi_get_modes, |
| }; |
| |
| static void ili9341_dbi_enable(struct drm_simple_display_pipe *pipe, |
| struct drm_crtc_state *crtc_state, |
| struct drm_plane_state *plane_state) |
| { |
| struct mipi_dbi_dev *dbidev = drm_to_mipi_dbi_dev(pipe->crtc.dev); |
| struct mipi_dbi *dbi = &dbidev->dbi; |
| u8 addr_mode; |
| int ret, idx; |
| |
| if (!drm_dev_enter(pipe->crtc.dev, &idx)) |
| return; |
| |
| ret = mipi_dbi_poweron_conditional_reset(dbidev); |
| if (ret < 0) |
| goto out_exit; |
| if (ret == 1) |
| goto out_enable; |
| |
| mipi_dbi_command(dbi, MIPI_DCS_SET_DISPLAY_OFF); |
| |
| mipi_dbi_command(dbi, ILI9341_POWERB, 0x00, 0xc1, 0x30); |
| mipi_dbi_command(dbi, ILI9341_POWER_SEQ, 0x64, 0x03, 0x12, 0x81); |
| mipi_dbi_command(dbi, ILI9341_DTCA, 0x85, 0x00, 0x78); |
| mipi_dbi_command(dbi, ILI9341_POWERA, 0x39, 0x2c, 0x00, 0x34, 0x02); |
| mipi_dbi_command(dbi, ILI9341_PRC, ILI9341_DBI_PRC_NORMAL); |
| mipi_dbi_command(dbi, ILI9341_DTCB, 0x00, 0x00); |
| |
| /* Power Control */ |
| mipi_dbi_command(dbi, ILI9341_POWER1, ILI9341_DBI_VCOMH_4P6V); |
| mipi_dbi_command(dbi, ILI9341_POWER2, ILI9341_DBI_PWR_2_DEFAULT); |
| /* VCOM */ |
| mipi_dbi_command(dbi, ILI9341_VCOM1, ILI9341_DBI_VCOM_1_VMH_4P25V, |
| ILI9341_DBI_VCOM_1_VML_1P5V); |
| mipi_dbi_command(dbi, ILI9341_VCOM2, ILI9341_DBI_VCOM_2_DEC_58); |
| |
| /* Memory Access Control */ |
| mipi_dbi_command(dbi, MIPI_DCS_SET_PIXEL_FORMAT, |
| MIPI_DCS_PIXEL_FMT_16BIT); |
| |
| /* Frame Rate */ |
| mipi_dbi_command(dbi, ILI9341_FRC, ILI9341_DBI_FRC_DIVA & 0x03, |
| ILI9341_DBI_FRC_RTNA & 0x1f); |
| |
| /* Gamma */ |
| mipi_dbi_command(dbi, ILI9341_3GAMMA_EN, 0x00); |
| mipi_dbi_command(dbi, MIPI_DCS_SET_GAMMA_CURVE, ILI9341_GAMMA_CURVE_1); |
| mipi_dbi_command(dbi, ILI9341_PGAMMA, |
| 0x0f, 0x31, 0x2b, 0x0c, 0x0e, 0x08, 0x4e, 0xf1, |
| 0x37, 0x07, 0x10, 0x03, 0x0e, 0x09, 0x00); |
| mipi_dbi_command(dbi, ILI9341_NGAMMA, |
| 0x00, 0x0e, 0x14, 0x03, 0x11, 0x07, 0x31, 0xc1, |
| 0x48, 0x08, 0x0f, 0x0c, 0x31, 0x36, 0x0f); |
| |
| /* DDRAM */ |
| mipi_dbi_command(dbi, ILI9341_ETMOD, ILI9341_DBI_EMS_GAS | |
| ILI9341_DBI_EMS_DTS | |
| ILI9341_DBI_EMS_GON); |
| |
| /* Display */ |
| mipi_dbi_command(dbi, ILI9341_DFC, 0x08, 0x82, 0x27, 0x00); |
| mipi_dbi_command(dbi, MIPI_DCS_EXIT_SLEEP_MODE); |
| msleep(100); |
| |
| mipi_dbi_command(dbi, MIPI_DCS_SET_DISPLAY_ON); |
| msleep(100); |
| |
| out_enable: |
| switch (dbidev->rotation) { |
| default: |
| addr_mode = ILI9341_MADCTL_MX; |
| break; |
| case 90: |
| addr_mode = ILI9341_MADCTL_MV; |
| break; |
| case 180: |
| addr_mode = ILI9341_MADCTL_MY; |
| break; |
| case 270: |
| addr_mode = ILI9341_MADCTL_MV | ILI9341_MADCTL_MY | |
| ILI9341_MADCTL_MX; |
| break; |
| } |
| |
| addr_mode |= ILI9341_MADCTL_BGR; |
| mipi_dbi_command(dbi, MIPI_DCS_SET_ADDRESS_MODE, addr_mode); |
| mipi_dbi_enable_flush(dbidev, crtc_state, plane_state); |
| drm_info(&dbidev->drm, "Initialized display serial interface\n"); |
| out_exit: |
| drm_dev_exit(idx); |
| } |
| |
| static const struct drm_simple_display_pipe_funcs ili9341_dbi_funcs = { |
| DRM_MIPI_DBI_SIMPLE_DISPLAY_PIPE_FUNCS(ili9341_dbi_enable), |
| }; |
| |
| static const struct drm_display_mode ili9341_dbi_mode = { |
| DRM_SIMPLE_MODE(240, 320, 37, 49), |
| }; |
| |
| DEFINE_DRM_GEM_DMA_FOPS(ili9341_dbi_fops); |
| |
| static struct drm_driver ili9341_dbi_driver = { |
| .driver_features = DRIVER_GEM | DRIVER_MODESET | DRIVER_ATOMIC, |
| .fops = &ili9341_dbi_fops, |
| DRM_GEM_DMA_DRIVER_OPS_VMAP, |
| .debugfs_init = mipi_dbi_debugfs_init, |
| .name = "ili9341", |
| .desc = "Ilitek ILI9341", |
| .date = "20210716", |
| .major = 1, |
| .minor = 0, |
| }; |
| |
| static int ili9341_dbi_probe(struct spi_device *spi, struct gpio_desc *dc, |
| struct gpio_desc *reset) |
| { |
| struct device *dev = &spi->dev; |
| struct mipi_dbi_dev *dbidev; |
| struct mipi_dbi *dbi; |
| struct drm_device *drm; |
| struct regulator *vcc; |
| u32 rotation = 0; |
| int ret; |
| |
| vcc = devm_regulator_get_optional(dev, "vcc"); |
| if (IS_ERR(vcc)) { |
| dev_err(dev, "get optional vcc failed\n"); |
| vcc = NULL; |
| } |
| |
| dbidev = devm_drm_dev_alloc(dev, &ili9341_dbi_driver, |
| struct mipi_dbi_dev, drm); |
| if (IS_ERR(dbidev)) |
| return PTR_ERR(dbidev); |
| |
| dbi = &dbidev->dbi; |
| drm = &dbidev->drm; |
| dbi->reset = reset; |
| dbidev->regulator = vcc; |
| |
| drm_mode_config_init(drm); |
| |
| dbidev->backlight = devm_of_find_backlight(dev); |
| if (IS_ERR(dbidev->backlight)) |
| return PTR_ERR(dbidev->backlight); |
| |
| device_property_read_u32(dev, "rotation", &rotation); |
| |
| ret = mipi_dbi_spi_init(spi, dbi, dc); |
| if (ret) |
| return ret; |
| |
| ret = mipi_dbi_dev_init(dbidev, &ili9341_dbi_funcs, |
| &ili9341_dbi_mode, rotation); |
| if (ret) |
| return ret; |
| |
| drm_mode_config_reset(drm); |
| |
| ret = drm_dev_register(drm, 0); |
| if (ret) |
| return ret; |
| |
| spi_set_drvdata(spi, drm); |
| |
| drm_fbdev_generic_setup(drm, 0); |
| |
| return 0; |
| } |
| |
| static int ili9341_dpi_probe(struct spi_device *spi, struct gpio_desc *dc, |
| struct gpio_desc *reset) |
| { |
| struct device *dev = &spi->dev; |
| struct ili9341 *ili; |
| int ret; |
| |
| ili = devm_kzalloc(dev, sizeof(struct ili9341), GFP_KERNEL); |
| if (!ili) |
| return -ENOMEM; |
| |
| ili->dbi = devm_kzalloc(dev, sizeof(struct mipi_dbi), |
| GFP_KERNEL); |
| if (!ili->dbi) |
| return -ENOMEM; |
| |
| ili->supplies[0].supply = "vci"; |
| ili->supplies[1].supply = "vddi"; |
| ili->supplies[2].supply = "vddi-led"; |
| ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(ili->supplies), |
| ili->supplies); |
| if (ret < 0) { |
| dev_err(dev, "failed to get regulators: %d\n", ret); |
| return ret; |
| } |
| |
| ret = mipi_dbi_spi_init(spi, ili->dbi, dc); |
| if (ret) |
| return ret; |
| |
| spi_set_drvdata(spi, ili); |
| ili->reset_gpio = reset; |
| /* |
| * Every new incarnation of this display must have a unique |
| * data entry for the system in this driver. |
| */ |
| ili->conf = of_device_get_match_data(dev); |
| if (!ili->conf) { |
| dev_err(dev, "missing device configuration\n"); |
| return -ENODEV; |
| } |
| |
| ili->max_spi_speed = ili->conf->max_spi_speed; |
| drm_panel_init(&ili->panel, dev, &ili9341_dpi_funcs, |
| DRM_MODE_CONNECTOR_DPI); |
| drm_panel_add(&ili->panel); |
| |
| return 0; |
| } |
| |
| static int ili9341_probe(struct spi_device *spi) |
| { |
| struct device *dev = &spi->dev; |
| struct gpio_desc *dc; |
| struct gpio_desc *reset; |
| const struct spi_device_id *id = spi_get_device_id(spi); |
| |
| reset = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH); |
| if (IS_ERR(reset)) |
| dev_err(dev, "Failed to get gpio 'reset'\n"); |
| |
| dc = devm_gpiod_get_optional(dev, "dc", GPIOD_OUT_LOW); |
| if (IS_ERR(dc)) |
| dev_err(dev, "Failed to get gpio 'dc'\n"); |
| |
| if (!strcmp(id->name, "sf-tc240t-9370-t")) |
| return ili9341_dpi_probe(spi, dc, reset); |
| else if (!strcmp(id->name, "yx240qv29")) |
| return ili9341_dbi_probe(spi, dc, reset); |
| |
| return -1; |
| } |
| |
| static void ili9341_remove(struct spi_device *spi) |
| { |
| const struct spi_device_id *id = spi_get_device_id(spi); |
| struct ili9341 *ili = spi_get_drvdata(spi); |
| struct drm_device *drm = spi_get_drvdata(spi); |
| |
| if (!strcmp(id->name, "sf-tc240t-9370-t")) { |
| ili9341_dpi_power_off(ili); |
| drm_panel_remove(&ili->panel); |
| } else if (!strcmp(id->name, "yx240qv29")) { |
| drm_dev_unplug(drm); |
| drm_atomic_helper_shutdown(drm); |
| } |
| } |
| |
| static void ili9341_shutdown(struct spi_device *spi) |
| { |
| const struct spi_device_id *id = spi_get_device_id(spi); |
| |
| if (!strcmp(id->name, "yx240qv29")) |
| drm_atomic_helper_shutdown(spi_get_drvdata(spi)); |
| } |
| |
| static const struct of_device_id ili9341_of_match[] = { |
| { |
| .compatible = "st,sf-tc240t-9370-t", |
| .data = &ili9341_stm32f429_disco_data, |
| }, |
| { |
| /* porting from tiny/ili9341.c |
| * for original mipi dbi compitable |
| */ |
| .compatible = "adafruit,yx240qv29", |
| .data = NULL, |
| }, |
| { } |
| }; |
| MODULE_DEVICE_TABLE(of, ili9341_of_match); |
| |
| static const struct spi_device_id ili9341_id[] = { |
| { "yx240qv29", 0 }, |
| { "sf-tc240t-9370-t", 0 }, |
| { } |
| }; |
| MODULE_DEVICE_TABLE(spi, ili9341_id); |
| |
| static struct spi_driver ili9341_driver = { |
| .probe = ili9341_probe, |
| .remove = ili9341_remove, |
| .shutdown = ili9341_shutdown, |
| .id_table = ili9341_id, |
| .driver = { |
| .name = "panel-ilitek-ili9341", |
| .of_match_table = ili9341_of_match, |
| }, |
| }; |
| module_spi_driver(ili9341_driver); |
| |
| MODULE_AUTHOR("Dillon Min <dillon.minfei@gmail.com>"); |
| MODULE_DESCRIPTION("ILI9341 LCD panel driver"); |
| MODULE_LICENSE("GPL v2"); |