| // SPDX-License-Identifier: GPL-2.0-or-later |
| /* |
| * RapidIO mport driver for Tsi721 PCIExpress-to-SRIO bridge |
| * |
| * Copyright 2011 Integrated Device Technology, Inc. |
| * Alexandre Bounine <alexandre.bounine@idt.com> |
| * Chul Kim <chul.kim@idt.com> |
| */ |
| |
| #include <linux/io.h> |
| #include <linux/errno.h> |
| #include <linux/init.h> |
| #include <linux/ioport.h> |
| #include <linux/kernel.h> |
| #include <linux/module.h> |
| #include <linux/pci.h> |
| #include <linux/rio.h> |
| #include <linux/rio_drv.h> |
| #include <linux/dma-mapping.h> |
| #include <linux/interrupt.h> |
| #include <linux/kfifo.h> |
| #include <linux/delay.h> |
| |
| #include "tsi721.h" |
| |
| #ifdef DEBUG |
| u32 tsi_dbg_level; |
| module_param_named(dbg_level, tsi_dbg_level, uint, S_IWUSR | S_IRUGO); |
| MODULE_PARM_DESC(dbg_level, "Debugging output level (default 0 = none)"); |
| #endif |
| |
| static int pcie_mrrs = -1; |
| module_param(pcie_mrrs, int, S_IRUGO); |
| MODULE_PARM_DESC(pcie_mrrs, "PCIe MRRS override value (0...5)"); |
| |
| static u8 mbox_sel = 0x0f; |
| module_param(mbox_sel, byte, S_IRUGO); |
| MODULE_PARM_DESC(mbox_sel, |
| "RIO Messaging MBOX Selection Mask (default: 0x0f = all)"); |
| |
| static DEFINE_SPINLOCK(tsi721_maint_lock); |
| |
| static void tsi721_omsg_handler(struct tsi721_device *priv, int ch); |
| static void tsi721_imsg_handler(struct tsi721_device *priv, int ch); |
| |
| /** |
| * tsi721_lcread - read from local SREP config space |
| * @mport: RapidIO master port info |
| * @index: ID of RapdiIO interface |
| * @offset: Offset into configuration space |
| * @len: Length (in bytes) of the maintenance transaction |
| * @data: Value to be read into |
| * |
| * Generates a local SREP space read. |
| * |
| * Returns: %0 on success or %-EINVAL on failure. |
| */ |
| static int tsi721_lcread(struct rio_mport *mport, int index, u32 offset, |
| int len, u32 *data) |
| { |
| struct tsi721_device *priv = mport->priv; |
| |
| if (len != sizeof(u32)) |
| return -EINVAL; /* only 32-bit access is supported */ |
| |
| *data = ioread32(priv->regs + offset); |
| |
| return 0; |
| } |
| |
| /** |
| * tsi721_lcwrite - write into local SREP config space |
| * @mport: RapidIO master port info |
| * @index: ID of RapdiIO interface |
| * @offset: Offset into configuration space |
| * @len: Length (in bytes) of the maintenance transaction |
| * @data: Value to be written |
| * |
| * Generates a local write into SREP configuration space. |
| * |
| * Returns: %0 on success or %-EINVAL on failure. |
| */ |
| static int tsi721_lcwrite(struct rio_mport *mport, int index, u32 offset, |
| int len, u32 data) |
| { |
| struct tsi721_device *priv = mport->priv; |
| |
| if (len != sizeof(u32)) |
| return -EINVAL; /* only 32-bit access is supported */ |
| |
| iowrite32(data, priv->regs + offset); |
| |
| return 0; |
| } |
| |
| /** |
| * tsi721_maint_dma - Helper function to generate RapidIO maintenance |
| * transactions using designated Tsi721 DMA channel. |
| * @priv: pointer to tsi721 private data |
| * @sys_size: RapdiIO transport system size |
| * @destid: Destination ID of transaction |
| * @hopcount: Number of hops to target device |
| * @offset: Offset into configuration space |
| * @len: Length (in bytes) of the maintenance transaction |
| * @data: Location to be read from or write into |
| * @do_wr: Operation flag (1 == MAINT_WR) |
| * |
| * Generates a RapidIO maintenance transaction (Read or Write). |
| * Returns: %0 on success and %-EINVAL or %-EFAULT on failure. |
| */ |
| static int tsi721_maint_dma(struct tsi721_device *priv, u32 sys_size, |
| u16 destid, u8 hopcount, u32 offset, int len, |
| u32 *data, int do_wr) |
| { |
| void __iomem *regs = priv->regs + TSI721_DMAC_BASE(priv->mdma.ch_id); |
| struct tsi721_dma_desc *bd_ptr; |
| u32 rd_count, swr_ptr, ch_stat; |
| unsigned long flags; |
| int i, err = 0; |
| u32 op = do_wr ? MAINT_WR : MAINT_RD; |
| |
| if (offset > (RIO_MAINT_SPACE_SZ - len) || (len != sizeof(u32))) |
| return -EINVAL; |
| |
| spin_lock_irqsave(&tsi721_maint_lock, flags); |
| |
| bd_ptr = priv->mdma.bd_base; |
| |
| rd_count = ioread32(regs + TSI721_DMAC_DRDCNT); |
| |
| /* Initialize DMA descriptor */ |
| bd_ptr[0].type_id = cpu_to_le32((DTYPE2 << 29) | (op << 19) | destid); |
| bd_ptr[0].bcount = cpu_to_le32((sys_size << 26) | 0x04); |
| bd_ptr[0].raddr_lo = cpu_to_le32((hopcount << 24) | offset); |
| bd_ptr[0].raddr_hi = 0; |
| if (do_wr) |
| bd_ptr[0].data[0] = cpu_to_be32p(data); |
| else |
| bd_ptr[0].data[0] = 0xffffffff; |
| |
| mb(); |
| |
| /* Start DMA operation */ |
| iowrite32(rd_count + 2, regs + TSI721_DMAC_DWRCNT); |
| ioread32(regs + TSI721_DMAC_DWRCNT); |
| i = 0; |
| |
| /* Wait until DMA transfer is finished */ |
| while ((ch_stat = ioread32(regs + TSI721_DMAC_STS)) |
| & TSI721_DMAC_STS_RUN) { |
| udelay(1); |
| if (++i >= 5000000) { |
| tsi_debug(MAINT, &priv->pdev->dev, |
| "DMA[%d] read timeout ch_status=%x", |
| priv->mdma.ch_id, ch_stat); |
| if (!do_wr) |
| *data = 0xffffffff; |
| err = -EIO; |
| goto err_out; |
| } |
| } |
| |
| if (ch_stat & TSI721_DMAC_STS_ABORT) { |
| /* If DMA operation aborted due to error, |
| * reinitialize DMA channel |
| */ |
| tsi_debug(MAINT, &priv->pdev->dev, "DMA ABORT ch_stat=%x", |
| ch_stat); |
| tsi_debug(MAINT, &priv->pdev->dev, |
| "OP=%d : destid=%x hc=%x off=%x", |
| do_wr ? MAINT_WR : MAINT_RD, |
| destid, hopcount, offset); |
| iowrite32(TSI721_DMAC_INT_ALL, regs + TSI721_DMAC_INT); |
| iowrite32(TSI721_DMAC_CTL_INIT, regs + TSI721_DMAC_CTL); |
| udelay(10); |
| iowrite32(0, regs + TSI721_DMAC_DWRCNT); |
| udelay(1); |
| if (!do_wr) |
| *data = 0xffffffff; |
| err = -EIO; |
| goto err_out; |
| } |
| |
| if (!do_wr) |
| *data = be32_to_cpu(bd_ptr[0].data[0]); |
| |
| /* |
| * Update descriptor status FIFO RD pointer. |
| * NOTE: Skipping check and clear FIFO entries because we are waiting |
| * for transfer to be completed. |
| */ |
| swr_ptr = ioread32(regs + TSI721_DMAC_DSWP); |
| iowrite32(swr_ptr, regs + TSI721_DMAC_DSRP); |
| |
| err_out: |
| spin_unlock_irqrestore(&tsi721_maint_lock, flags); |
| |
| return err; |
| } |
| |
| /** |
| * tsi721_cread_dma - Generate a RapidIO maintenance read transaction |
| * using Tsi721 BDMA engine. |
| * @mport: RapidIO master port control structure |
| * @index: ID of RapdiIO interface |
| * @destid: Destination ID of transaction |
| * @hopcount: Number of hops to target device |
| * @offset: Offset into configuration space |
| * @len: Length (in bytes) of the maintenance transaction |
| * @data: Location to be read into |
| * |
| * Generates a RapidIO maintenance read transaction. |
| * Returns: %0 on success and %-EINVAL or %-EFAULT on failure. |
| */ |
| static int tsi721_cread_dma(struct rio_mport *mport, int index, u16 destid, |
| u8 hopcount, u32 offset, int len, u32 *data) |
| { |
| struct tsi721_device *priv = mport->priv; |
| |
| return tsi721_maint_dma(priv, mport->sys_size, destid, hopcount, |
| offset, len, data, 0); |
| } |
| |
| /** |
| * tsi721_cwrite_dma - Generate a RapidIO maintenance write transaction |
| * using Tsi721 BDMA engine |
| * @mport: RapidIO master port control structure |
| * @index: ID of RapdiIO interface |
| * @destid: Destination ID of transaction |
| * @hopcount: Number of hops to target device |
| * @offset: Offset into configuration space |
| * @len: Length (in bytes) of the maintenance transaction |
| * @data: Value to be written |
| * |
| * Generates a RapidIO maintenance write transaction. |
| * Returns: %0 on success and %-EINVAL or %-EFAULT on failure. |
| */ |
| static int tsi721_cwrite_dma(struct rio_mport *mport, int index, u16 destid, |
| u8 hopcount, u32 offset, int len, u32 data) |
| { |
| struct tsi721_device *priv = mport->priv; |
| u32 temp = data; |
| |
| return tsi721_maint_dma(priv, mport->sys_size, destid, hopcount, |
| offset, len, &temp, 1); |
| } |
| |
| /** |
| * tsi721_pw_handler - Tsi721 inbound port-write interrupt handler |
| * @priv: tsi721 device private structure |
| * |
| * Handles inbound port-write interrupts. Copies PW message from an internal |
| * buffer into PW message FIFO and schedules deferred routine to process |
| * queued messages. |
| * |
| * Returns: %0 |
| */ |
| static int |
| tsi721_pw_handler(struct tsi721_device *priv) |
| { |
| u32 pw_stat; |
| u32 pw_buf[TSI721_RIO_PW_MSG_SIZE/sizeof(u32)]; |
| |
| |
| pw_stat = ioread32(priv->regs + TSI721_RIO_PW_RX_STAT); |
| |
| if (pw_stat & TSI721_RIO_PW_RX_STAT_PW_VAL) { |
| pw_buf[0] = ioread32(priv->regs + TSI721_RIO_PW_RX_CAPT(0)); |
| pw_buf[1] = ioread32(priv->regs + TSI721_RIO_PW_RX_CAPT(1)); |
| pw_buf[2] = ioread32(priv->regs + TSI721_RIO_PW_RX_CAPT(2)); |
| pw_buf[3] = ioread32(priv->regs + TSI721_RIO_PW_RX_CAPT(3)); |
| |
| /* Queue PW message (if there is room in FIFO), |
| * otherwise discard it. |
| */ |
| spin_lock(&priv->pw_fifo_lock); |
| if (kfifo_avail(&priv->pw_fifo) >= TSI721_RIO_PW_MSG_SIZE) |
| kfifo_in(&priv->pw_fifo, pw_buf, |
| TSI721_RIO_PW_MSG_SIZE); |
| else |
| priv->pw_discard_count++; |
| spin_unlock(&priv->pw_fifo_lock); |
| } |
| |
| /* Clear pending PW interrupts */ |
| iowrite32(TSI721_RIO_PW_RX_STAT_PW_DISC | TSI721_RIO_PW_RX_STAT_PW_VAL, |
| priv->regs + TSI721_RIO_PW_RX_STAT); |
| |
| schedule_work(&priv->pw_work); |
| |
| return 0; |
| } |
| |
| static void tsi721_pw_dpc(struct work_struct *work) |
| { |
| struct tsi721_device *priv = container_of(work, struct tsi721_device, |
| pw_work); |
| union rio_pw_msg pwmsg; |
| |
| /* |
| * Process port-write messages |
| */ |
| while (kfifo_out_spinlocked(&priv->pw_fifo, (unsigned char *)&pwmsg, |
| TSI721_RIO_PW_MSG_SIZE, &priv->pw_fifo_lock)) { |
| /* Pass the port-write message to RIO core for processing */ |
| rio_inb_pwrite_handler(&priv->mport, &pwmsg); |
| } |
| } |
| |
| /** |
| * tsi721_pw_enable - enable/disable port-write interface init |
| * @mport: Master port implementing the port write unit |
| * @enable: 1=enable; 0=disable port-write message handling |
| * |
| * Returns: %0 |
| */ |
| static int tsi721_pw_enable(struct rio_mport *mport, int enable) |
| { |
| struct tsi721_device *priv = mport->priv; |
| u32 rval; |
| |
| rval = ioread32(priv->regs + TSI721_RIO_EM_INT_ENABLE); |
| |
| if (enable) |
| rval |= TSI721_RIO_EM_INT_ENABLE_PW_RX; |
| else |
| rval &= ~TSI721_RIO_EM_INT_ENABLE_PW_RX; |
| |
| /* Clear pending PW interrupts */ |
| iowrite32(TSI721_RIO_PW_RX_STAT_PW_DISC | TSI721_RIO_PW_RX_STAT_PW_VAL, |
| priv->regs + TSI721_RIO_PW_RX_STAT); |
| /* Update enable bits */ |
| iowrite32(rval, priv->regs + TSI721_RIO_EM_INT_ENABLE); |
| |
| return 0; |
| } |
| |
| /** |
| * tsi721_dsend - Send a RapidIO doorbell |
| * @mport: RapidIO master port info |
| * @index: ID of RapidIO interface |
| * @destid: Destination ID of target device |
| * @data: 16-bit info field of RapidIO doorbell |
| * |
| * Sends a RapidIO doorbell message. |
| * |
| * Returns: %0 |
| */ |
| static int tsi721_dsend(struct rio_mport *mport, int index, |
| u16 destid, u16 data) |
| { |
| struct tsi721_device *priv = mport->priv; |
| u32 offset; |
| |
| offset = (((mport->sys_size) ? RIO_TT_CODE_16 : RIO_TT_CODE_8) << 18) | |
| (destid << 2); |
| |
| tsi_debug(DBELL, &priv->pdev->dev, |
| "Send Doorbell 0x%04x to destID 0x%x", data, destid); |
| iowrite16be(data, priv->odb_base + offset); |
| |
| return 0; |
| } |
| |
| /** |
| * tsi721_dbell_handler - Tsi721 doorbell interrupt handler |
| * @priv: tsi721 device-specific data structure |
| * |
| * Handles inbound doorbell interrupts. Copies doorbell entry from an internal |
| * buffer into DB message FIFO and schedules deferred routine to process |
| * queued DBs. |
| * |
| * Returns: %0 |
| */ |
| static int |
| tsi721_dbell_handler(struct tsi721_device *priv) |
| { |
| u32 regval; |
| |
| /* Disable IDB interrupts */ |
| regval = ioread32(priv->regs + TSI721_SR_CHINTE(IDB_QUEUE)); |
| regval &= ~TSI721_SR_CHINT_IDBQRCV; |
| iowrite32(regval, |
| priv->regs + TSI721_SR_CHINTE(IDB_QUEUE)); |
| |
| schedule_work(&priv->idb_work); |
| |
| return 0; |
| } |
| |
| static void tsi721_db_dpc(struct work_struct *work) |
| { |
| struct tsi721_device *priv = container_of(work, struct tsi721_device, |
| idb_work); |
| struct rio_mport *mport; |
| struct rio_dbell *dbell; |
| int found = 0; |
| u32 wr_ptr, rd_ptr; |
| u64 *idb_entry; |
| u32 regval; |
| union { |
| u64 msg; |
| u8 bytes[8]; |
| } idb; |
| |
| /* |
| * Process queued inbound doorbells |
| */ |
| mport = &priv->mport; |
| |
| wr_ptr = ioread32(priv->regs + TSI721_IDQ_WP(IDB_QUEUE)) % IDB_QSIZE; |
| rd_ptr = ioread32(priv->regs + TSI721_IDQ_RP(IDB_QUEUE)) % IDB_QSIZE; |
| |
| while (wr_ptr != rd_ptr) { |
| idb_entry = (u64 *)(priv->idb_base + |
| (TSI721_IDB_ENTRY_SIZE * rd_ptr)); |
| rd_ptr++; |
| rd_ptr %= IDB_QSIZE; |
| idb.msg = *idb_entry; |
| *idb_entry = 0; |
| |
| /* Process one doorbell */ |
| list_for_each_entry(dbell, &mport->dbells, node) { |
| if ((dbell->res->start <= DBELL_INF(idb.bytes)) && |
| (dbell->res->end >= DBELL_INF(idb.bytes))) { |
| found = 1; |
| break; |
| } |
| } |
| |
| if (found) { |
| dbell->dinb(mport, dbell->dev_id, DBELL_SID(idb.bytes), |
| DBELL_TID(idb.bytes), DBELL_INF(idb.bytes)); |
| } else { |
| tsi_debug(DBELL, &priv->pdev->dev, |
| "spurious IDB sid %2.2x tid %2.2x info %4.4x", |
| DBELL_SID(idb.bytes), DBELL_TID(idb.bytes), |
| DBELL_INF(idb.bytes)); |
| } |
| |
| wr_ptr = ioread32(priv->regs + |
| TSI721_IDQ_WP(IDB_QUEUE)) % IDB_QSIZE; |
| } |
| |
| iowrite32(rd_ptr & (IDB_QSIZE - 1), |
| priv->regs + TSI721_IDQ_RP(IDB_QUEUE)); |
| |
| /* Re-enable IDB interrupts */ |
| regval = ioread32(priv->regs + TSI721_SR_CHINTE(IDB_QUEUE)); |
| regval |= TSI721_SR_CHINT_IDBQRCV; |
| iowrite32(regval, |
| priv->regs + TSI721_SR_CHINTE(IDB_QUEUE)); |
| |
| wr_ptr = ioread32(priv->regs + TSI721_IDQ_WP(IDB_QUEUE)) % IDB_QSIZE; |
| if (wr_ptr != rd_ptr) |
| schedule_work(&priv->idb_work); |
| } |
| |
| /** |
| * tsi721_irqhandler - Tsi721 interrupt handler |
| * @irq: Linux interrupt number |
| * @ptr: Pointer to interrupt-specific data (tsi721_device structure) |
| * |
| * Handles Tsi721 interrupts signaled using MSI and INTA. Checks reported |
| * interrupt events and calls an event-specific handler(s). |
| * |
| * Returns: %IRQ_HANDLED or %IRQ_NONE |
| */ |
| static irqreturn_t tsi721_irqhandler(int irq, void *ptr) |
| { |
| struct tsi721_device *priv = (struct tsi721_device *)ptr; |
| u32 dev_int; |
| u32 dev_ch_int; |
| u32 intval; |
| u32 ch_inte; |
| |
| /* For MSI mode disable all device-level interrupts */ |
| if (priv->flags & TSI721_USING_MSI) |
| iowrite32(0, priv->regs + TSI721_DEV_INTE); |
| |
| dev_int = ioread32(priv->regs + TSI721_DEV_INT); |
| if (!dev_int) |
| return IRQ_NONE; |
| |
| dev_ch_int = ioread32(priv->regs + TSI721_DEV_CHAN_INT); |
| |
| if (dev_int & TSI721_DEV_INT_SR2PC_CH) { |
| /* Service SR2PC Channel interrupts */ |
| if (dev_ch_int & TSI721_INT_SR2PC_CHAN(IDB_QUEUE)) { |
| /* Service Inbound Doorbell interrupt */ |
| intval = ioread32(priv->regs + |
| TSI721_SR_CHINT(IDB_QUEUE)); |
| if (intval & TSI721_SR_CHINT_IDBQRCV) |
| tsi721_dbell_handler(priv); |
| else |
| tsi_info(&priv->pdev->dev, |
| "Unsupported SR_CH_INT %x", intval); |
| |
| /* Clear interrupts */ |
| iowrite32(intval, |
| priv->regs + TSI721_SR_CHINT(IDB_QUEUE)); |
| ioread32(priv->regs + TSI721_SR_CHINT(IDB_QUEUE)); |
| } |
| } |
| |
| if (dev_int & TSI721_DEV_INT_SMSG_CH) { |
| int ch; |
| |
| /* |
| * Service channel interrupts from Messaging Engine |
| */ |
| |
| if (dev_ch_int & TSI721_INT_IMSG_CHAN_M) { /* Inbound Msg */ |
| /* Disable signaled OB MSG Channel interrupts */ |
| ch_inte = ioread32(priv->regs + TSI721_DEV_CHAN_INTE); |
| ch_inte &= ~(dev_ch_int & TSI721_INT_IMSG_CHAN_M); |
| iowrite32(ch_inte, priv->regs + TSI721_DEV_CHAN_INTE); |
| |
| /* |
| * Process Inbound Message interrupt for each MBOX |
| */ |
| for (ch = 4; ch < RIO_MAX_MBOX + 4; ch++) { |
| if (!(dev_ch_int & TSI721_INT_IMSG_CHAN(ch))) |
| continue; |
| tsi721_imsg_handler(priv, ch); |
| } |
| } |
| |
| if (dev_ch_int & TSI721_INT_OMSG_CHAN_M) { /* Outbound Msg */ |
| /* Disable signaled OB MSG Channel interrupts */ |
| ch_inte = ioread32(priv->regs + TSI721_DEV_CHAN_INTE); |
| ch_inte &= ~(dev_ch_int & TSI721_INT_OMSG_CHAN_M); |
| iowrite32(ch_inte, priv->regs + TSI721_DEV_CHAN_INTE); |
| |
| /* |
| * Process Outbound Message interrupts for each MBOX |
| */ |
| |
| for (ch = 0; ch < RIO_MAX_MBOX; ch++) { |
| if (!(dev_ch_int & TSI721_INT_OMSG_CHAN(ch))) |
| continue; |
| tsi721_omsg_handler(priv, ch); |
| } |
| } |
| } |
| |
| if (dev_int & TSI721_DEV_INT_SRIO) { |
| /* Service SRIO MAC interrupts */ |
| intval = ioread32(priv->regs + TSI721_RIO_EM_INT_STAT); |
| if (intval & TSI721_RIO_EM_INT_STAT_PW_RX) |
| tsi721_pw_handler(priv); |
| } |
| |
| #ifdef CONFIG_RAPIDIO_DMA_ENGINE |
| if (dev_int & TSI721_DEV_INT_BDMA_CH) { |
| int ch; |
| |
| if (dev_ch_int & TSI721_INT_BDMA_CHAN_M) { |
| tsi_debug(DMA, &priv->pdev->dev, |
| "IRQ from DMA channel 0x%08x", dev_ch_int); |
| |
| for (ch = 0; ch < TSI721_DMA_MAXCH; ch++) { |
| if (!(dev_ch_int & TSI721_INT_BDMA_CHAN(ch))) |
| continue; |
| tsi721_bdma_handler(&priv->bdma[ch]); |
| } |
| } |
| } |
| #endif |
| |
| /* For MSI mode re-enable device-level interrupts */ |
| if (priv->flags & TSI721_USING_MSI) { |
| dev_int = TSI721_DEV_INT_SR2PC_CH | TSI721_DEV_INT_SRIO | |
| TSI721_DEV_INT_SMSG_CH | TSI721_DEV_INT_BDMA_CH; |
| iowrite32(dev_int, priv->regs + TSI721_DEV_INTE); |
| } |
| |
| return IRQ_HANDLED; |
| } |
| |
| static void tsi721_interrupts_init(struct tsi721_device *priv) |
| { |
| u32 intr; |
| |
| /* Enable IDB interrupts */ |
| iowrite32(TSI721_SR_CHINT_ALL, |
| priv->regs + TSI721_SR_CHINT(IDB_QUEUE)); |
| iowrite32(TSI721_SR_CHINT_IDBQRCV, |
| priv->regs + TSI721_SR_CHINTE(IDB_QUEUE)); |
| |
| /* Enable SRIO MAC interrupts */ |
| iowrite32(TSI721_RIO_EM_DEV_INT_EN_INT, |
| priv->regs + TSI721_RIO_EM_DEV_INT_EN); |
| |
| /* Enable interrupts from channels in use */ |
| #ifdef CONFIG_RAPIDIO_DMA_ENGINE |
| intr = TSI721_INT_SR2PC_CHAN(IDB_QUEUE) | |
| (TSI721_INT_BDMA_CHAN_M & |
| ~TSI721_INT_BDMA_CHAN(TSI721_DMACH_MAINT)); |
| #else |
| intr = TSI721_INT_SR2PC_CHAN(IDB_QUEUE); |
| #endif |
| iowrite32(intr, priv->regs + TSI721_DEV_CHAN_INTE); |
| |
| if (priv->flags & TSI721_USING_MSIX) |
| intr = TSI721_DEV_INT_SRIO; |
| else |
| intr = TSI721_DEV_INT_SR2PC_CH | TSI721_DEV_INT_SRIO | |
| TSI721_DEV_INT_SMSG_CH | TSI721_DEV_INT_BDMA_CH; |
| |
| iowrite32(intr, priv->regs + TSI721_DEV_INTE); |
| ioread32(priv->regs + TSI721_DEV_INTE); |
| } |
| |
| #ifdef CONFIG_PCI_MSI |
| /** |
| * tsi721_omsg_msix - MSI-X interrupt handler for outbound messaging |
| * @irq: Linux interrupt number |
| * @ptr: Pointer to interrupt-specific data (tsi721_device structure) |
| * |
| * Handles outbound messaging interrupts signaled using MSI-X. |
| * |
| * Returns: %IRQ_HANDLED |
| */ |
| static irqreturn_t tsi721_omsg_msix(int irq, void *ptr) |
| { |
| struct tsi721_device *priv = (struct tsi721_device *)ptr; |
| int mbox; |
| |
| mbox = (irq - priv->msix[TSI721_VECT_OMB0_DONE].vector) % RIO_MAX_MBOX; |
| tsi721_omsg_handler(priv, mbox); |
| return IRQ_HANDLED; |
| } |
| |
| /** |
| * tsi721_imsg_msix - MSI-X interrupt handler for inbound messaging |
| * @irq: Linux interrupt number |
| * @ptr: Pointer to interrupt-specific data (tsi721_device structure) |
| * |
| * Handles inbound messaging interrupts signaled using MSI-X. |
| * |
| * Returns: %IRQ_HANDLED |
| */ |
| static irqreturn_t tsi721_imsg_msix(int irq, void *ptr) |
| { |
| struct tsi721_device *priv = (struct tsi721_device *)ptr; |
| int mbox; |
| |
| mbox = (irq - priv->msix[TSI721_VECT_IMB0_RCV].vector) % RIO_MAX_MBOX; |
| tsi721_imsg_handler(priv, mbox + 4); |
| return IRQ_HANDLED; |
| } |
| |
| /** |
| * tsi721_srio_msix - Tsi721 MSI-X SRIO MAC interrupt handler |
| * @irq: Linux interrupt number |
| * @ptr: Pointer to interrupt-specific data (tsi721_device structure) |
| * |
| * Handles Tsi721 interrupts from SRIO MAC. |
| * |
| * Returns: %IRQ_HANDLED |
| */ |
| static irqreturn_t tsi721_srio_msix(int irq, void *ptr) |
| { |
| struct tsi721_device *priv = (struct tsi721_device *)ptr; |
| u32 srio_int; |
| |
| /* Service SRIO MAC interrupts */ |
| srio_int = ioread32(priv->regs + TSI721_RIO_EM_INT_STAT); |
| if (srio_int & TSI721_RIO_EM_INT_STAT_PW_RX) |
| tsi721_pw_handler(priv); |
| |
| return IRQ_HANDLED; |
| } |
| |
| /** |
| * tsi721_sr2pc_ch_msix - Tsi721 MSI-X SR2PC Channel interrupt handler |
| * @irq: Linux interrupt number |
| * @ptr: Pointer to interrupt-specific data (tsi721_device structure) |
| * |
| * Handles Tsi721 interrupts from SR2PC Channel. |
| * NOTE: At this moment services only one SR2PC channel associated with inbound |
| * doorbells. |
| * |
| * Returns: %IRQ_HANDLED |
| */ |
| static irqreturn_t tsi721_sr2pc_ch_msix(int irq, void *ptr) |
| { |
| struct tsi721_device *priv = (struct tsi721_device *)ptr; |
| u32 sr_ch_int; |
| |
| /* Service Inbound DB interrupt from SR2PC channel */ |
| sr_ch_int = ioread32(priv->regs + TSI721_SR_CHINT(IDB_QUEUE)); |
| if (sr_ch_int & TSI721_SR_CHINT_IDBQRCV) |
| tsi721_dbell_handler(priv); |
| |
| /* Clear interrupts */ |
| iowrite32(sr_ch_int, priv->regs + TSI721_SR_CHINT(IDB_QUEUE)); |
| /* Read back to ensure that interrupt was cleared */ |
| sr_ch_int = ioread32(priv->regs + TSI721_SR_CHINT(IDB_QUEUE)); |
| |
| return IRQ_HANDLED; |
| } |
| |
| /** |
| * tsi721_request_msix - register interrupt service for MSI-X mode. |
| * @priv: tsi721 device-specific data structure |
| * |
| * Registers MSI-X interrupt service routines for interrupts that are active |
| * immediately after mport initialization. Messaging interrupt service routines |
| * should be registered during corresponding open requests. |
| * |
| * Returns: %0 on success or -errno value on failure. |
| */ |
| static int tsi721_request_msix(struct tsi721_device *priv) |
| { |
| int err = 0; |
| |
| err = request_irq(priv->msix[TSI721_VECT_IDB].vector, |
| tsi721_sr2pc_ch_msix, 0, |
| priv->msix[TSI721_VECT_IDB].irq_name, (void *)priv); |
| if (err) |
| return err; |
| |
| err = request_irq(priv->msix[TSI721_VECT_PWRX].vector, |
| tsi721_srio_msix, 0, |
| priv->msix[TSI721_VECT_PWRX].irq_name, (void *)priv); |
| if (err) { |
| free_irq(priv->msix[TSI721_VECT_IDB].vector, (void *)priv); |
| return err; |
| } |
| |
| return 0; |
| } |
| |
| /** |
| * tsi721_enable_msix - Attempts to enable MSI-X support for Tsi721. |
| * @priv: pointer to tsi721 private data |
| * |
| * Configures MSI-X support for Tsi721. Supports only an exact number |
| * of requested vectors. |
| * |
| * Returns: %0 on success or -errno value on failure. |
| */ |
| static int tsi721_enable_msix(struct tsi721_device *priv) |
| { |
| struct msix_entry entries[TSI721_VECT_MAX]; |
| int err; |
| int i; |
| |
| entries[TSI721_VECT_IDB].entry = TSI721_MSIX_SR2PC_IDBQ_RCV(IDB_QUEUE); |
| entries[TSI721_VECT_PWRX].entry = TSI721_MSIX_SRIO_MAC_INT; |
| |
| /* |
| * Initialize MSI-X entries for Messaging Engine: |
| * this driver supports four RIO mailboxes (inbound and outbound) |
| * NOTE: Inbound message MBOX 0...4 use IB channels 4...7. Therefore |
| * offset +4 is added to IB MBOX number. |
| */ |
| for (i = 0; i < RIO_MAX_MBOX; i++) { |
| entries[TSI721_VECT_IMB0_RCV + i].entry = |
| TSI721_MSIX_IMSG_DQ_RCV(i + 4); |
| entries[TSI721_VECT_IMB0_INT + i].entry = |
| TSI721_MSIX_IMSG_INT(i + 4); |
| entries[TSI721_VECT_OMB0_DONE + i].entry = |
| TSI721_MSIX_OMSG_DONE(i); |
| entries[TSI721_VECT_OMB0_INT + i].entry = |
| TSI721_MSIX_OMSG_INT(i); |
| } |
| |
| #ifdef CONFIG_RAPIDIO_DMA_ENGINE |
| /* |
| * Initialize MSI-X entries for Block DMA Engine: |
| * this driver supports XXX DMA channels |
| * (one is reserved for SRIO maintenance transactions) |
| */ |
| for (i = 0; i < TSI721_DMA_CHNUM; i++) { |
| entries[TSI721_VECT_DMA0_DONE + i].entry = |
| TSI721_MSIX_DMACH_DONE(i); |
| entries[TSI721_VECT_DMA0_INT + i].entry = |
| TSI721_MSIX_DMACH_INT(i); |
| } |
| #endif /* CONFIG_RAPIDIO_DMA_ENGINE */ |
| |
| err = pci_enable_msix_exact(priv->pdev, entries, ARRAY_SIZE(entries)); |
| if (err) { |
| tsi_err(&priv->pdev->dev, |
| "Failed to enable MSI-X (err=%d)", err); |
| return err; |
| } |
| |
| /* |
| * Copy MSI-X vector information into tsi721 private structure |
| */ |
| priv->msix[TSI721_VECT_IDB].vector = entries[TSI721_VECT_IDB].vector; |
| snprintf(priv->msix[TSI721_VECT_IDB].irq_name, IRQ_DEVICE_NAME_MAX, |
| DRV_NAME "-idb@pci:%s", pci_name(priv->pdev)); |
| priv->msix[TSI721_VECT_PWRX].vector = entries[TSI721_VECT_PWRX].vector; |
| snprintf(priv->msix[TSI721_VECT_PWRX].irq_name, IRQ_DEVICE_NAME_MAX, |
| DRV_NAME "-pwrx@pci:%s", pci_name(priv->pdev)); |
| |
| for (i = 0; i < RIO_MAX_MBOX; i++) { |
| priv->msix[TSI721_VECT_IMB0_RCV + i].vector = |
| entries[TSI721_VECT_IMB0_RCV + i].vector; |
| snprintf(priv->msix[TSI721_VECT_IMB0_RCV + i].irq_name, |
| IRQ_DEVICE_NAME_MAX, DRV_NAME "-imbr%d@pci:%s", |
| i, pci_name(priv->pdev)); |
| |
| priv->msix[TSI721_VECT_IMB0_INT + i].vector = |
| entries[TSI721_VECT_IMB0_INT + i].vector; |
| snprintf(priv->msix[TSI721_VECT_IMB0_INT + i].irq_name, |
| IRQ_DEVICE_NAME_MAX, DRV_NAME "-imbi%d@pci:%s", |
| i, pci_name(priv->pdev)); |
| |
| priv->msix[TSI721_VECT_OMB0_DONE + i].vector = |
| entries[TSI721_VECT_OMB0_DONE + i].vector; |
| snprintf(priv->msix[TSI721_VECT_OMB0_DONE + i].irq_name, |
| IRQ_DEVICE_NAME_MAX, DRV_NAME "-ombd%d@pci:%s", |
| i, pci_name(priv->pdev)); |
| |
| priv->msix[TSI721_VECT_OMB0_INT + i].vector = |
| entries[TSI721_VECT_OMB0_INT + i].vector; |
| snprintf(priv->msix[TSI721_VECT_OMB0_INT + i].irq_name, |
| IRQ_DEVICE_NAME_MAX, DRV_NAME "-ombi%d@pci:%s", |
| i, pci_name(priv->pdev)); |
| } |
| |
| #ifdef CONFIG_RAPIDIO_DMA_ENGINE |
| for (i = 0; i < TSI721_DMA_CHNUM; i++) { |
| priv->msix[TSI721_VECT_DMA0_DONE + i].vector = |
| entries[TSI721_VECT_DMA0_DONE + i].vector; |
| snprintf(priv->msix[TSI721_VECT_DMA0_DONE + i].irq_name, |
| IRQ_DEVICE_NAME_MAX, DRV_NAME "-dmad%d@pci:%s", |
| i, pci_name(priv->pdev)); |
| |
| priv->msix[TSI721_VECT_DMA0_INT + i].vector = |
| entries[TSI721_VECT_DMA0_INT + i].vector; |
| snprintf(priv->msix[TSI721_VECT_DMA0_INT + i].irq_name, |
| IRQ_DEVICE_NAME_MAX, DRV_NAME "-dmai%d@pci:%s", |
| i, pci_name(priv->pdev)); |
| } |
| #endif /* CONFIG_RAPIDIO_DMA_ENGINE */ |
| |
| return 0; |
| } |
| #endif /* CONFIG_PCI_MSI */ |
| |
| static int tsi721_request_irq(struct tsi721_device *priv) |
| { |
| int err; |
| |
| #ifdef CONFIG_PCI_MSI |
| if (priv->flags & TSI721_USING_MSIX) |
| err = tsi721_request_msix(priv); |
| else |
| #endif |
| err = request_irq(priv->pdev->irq, tsi721_irqhandler, |
| (priv->flags & TSI721_USING_MSI) ? 0 : IRQF_SHARED, |
| DRV_NAME, (void *)priv); |
| |
| if (err) |
| tsi_err(&priv->pdev->dev, |
| "Unable to allocate interrupt, err=%d", err); |
| |
| return err; |
| } |
| |
| static void tsi721_free_irq(struct tsi721_device *priv) |
| { |
| #ifdef CONFIG_PCI_MSI |
| if (priv->flags & TSI721_USING_MSIX) { |
| free_irq(priv->msix[TSI721_VECT_IDB].vector, (void *)priv); |
| free_irq(priv->msix[TSI721_VECT_PWRX].vector, (void *)priv); |
| } else |
| #endif |
| free_irq(priv->pdev->irq, (void *)priv); |
| } |
| |
| static int |
| tsi721_obw_alloc(struct tsi721_device *priv, struct tsi721_obw_bar *pbar, |
| u32 size, int *win_id) |
| { |
| u64 win_base; |
| u64 bar_base; |
| u64 bar_end; |
| u32 align; |
| struct tsi721_ob_win *win; |
| struct tsi721_ob_win *new_win = NULL; |
| int new_win_idx = -1; |
| int i = 0; |
| |
| bar_base = pbar->base; |
| bar_end = bar_base + pbar->size; |
| win_base = bar_base; |
| align = size/TSI721_PC2SR_ZONES; |
| |
| while (i < TSI721_IBWIN_NUM) { |
| for (i = 0; i < TSI721_IBWIN_NUM; i++) { |
| if (!priv->ob_win[i].active) { |
| if (new_win == NULL) { |
| new_win = &priv->ob_win[i]; |
| new_win_idx = i; |
| } |
| continue; |
| } |
| |
| /* |
| * If this window belongs to the current BAR check it |
| * for overlap |
| */ |
| win = &priv->ob_win[i]; |
| |
| if (win->base >= bar_base && win->base < bar_end) { |
| if (win_base < (win->base + win->size) && |
| (win_base + size) > win->base) { |
| /* Overlap detected */ |
| win_base = win->base + win->size; |
| win_base = ALIGN(win_base, align); |
| break; |
| } |
| } |
| } |
| } |
| |
| if (win_base + size > bar_end) |
| return -ENOMEM; |
| |
| if (!new_win) { |
| tsi_err(&priv->pdev->dev, "OBW count tracking failed"); |
| return -EIO; |
| } |
| |
| new_win->active = true; |
| new_win->base = win_base; |
| new_win->size = size; |
| new_win->pbar = pbar; |
| priv->obwin_cnt--; |
| pbar->free -= size; |
| *win_id = new_win_idx; |
| return 0; |
| } |
| |
| static int tsi721_map_outb_win(struct rio_mport *mport, u16 destid, u64 rstart, |
| u32 size, u32 flags, dma_addr_t *laddr) |
| { |
| struct tsi721_device *priv = mport->priv; |
| int i; |
| struct tsi721_obw_bar *pbar; |
| struct tsi721_ob_win *ob_win; |
| int obw = -1; |
| u32 rval; |
| u64 rio_addr; |
| u32 zsize; |
| int ret = -ENOMEM; |
| |
| tsi_debug(OBW, &priv->pdev->dev, |
| "did=%d ra=0x%llx sz=0x%x", destid, rstart, size); |
| |
| if (!is_power_of_2(size) || (size < 0x8000) || (rstart & (size - 1))) |
| return -EINVAL; |
| |
| if (priv->obwin_cnt == 0) |
| return -EBUSY; |
| |
| for (i = 0; i < 2; i++) { |
| if (priv->p2r_bar[i].free >= size) { |
| pbar = &priv->p2r_bar[i]; |
| ret = tsi721_obw_alloc(priv, pbar, size, &obw); |
| if (!ret) |
| break; |
| } |
| } |
| |
| if (ret) |
| return ret; |
| |
| WARN_ON(obw == -1); |
| ob_win = &priv->ob_win[obw]; |
| ob_win->destid = destid; |
| ob_win->rstart = rstart; |
| tsi_debug(OBW, &priv->pdev->dev, |
| "allocated OBW%d @%llx", obw, ob_win->base); |
| |
| /* |
| * Configure Outbound Window |
| */ |
| |
| zsize = size/TSI721_PC2SR_ZONES; |
| rio_addr = rstart; |
| |
| /* |
| * Program Address Translation Zones: |
| * This implementation uses all 8 zones associated wit window. |
| */ |
| for (i = 0; i < TSI721_PC2SR_ZONES; i++) { |
| |
| while (ioread32(priv->regs + TSI721_ZONE_SEL) & |
| TSI721_ZONE_SEL_GO) { |
| udelay(1); |
| } |
| |
| rval = (u32)(rio_addr & TSI721_LUT_DATA0_ADD) | |
| TSI721_LUT_DATA0_NREAD | TSI721_LUT_DATA0_NWR; |
| iowrite32(rval, priv->regs + TSI721_LUT_DATA0); |
| rval = (u32)(rio_addr >> 32); |
| iowrite32(rval, priv->regs + TSI721_LUT_DATA1); |
| rval = destid; |
| iowrite32(rval, priv->regs + TSI721_LUT_DATA2); |
| |
| rval = TSI721_ZONE_SEL_GO | (obw << 3) | i; |
| iowrite32(rval, priv->regs + TSI721_ZONE_SEL); |
| |
| rio_addr += zsize; |
| } |
| |
| iowrite32(TSI721_OBWIN_SIZE(size) << 8, |
| priv->regs + TSI721_OBWINSZ(obw)); |
| iowrite32((u32)(ob_win->base >> 32), priv->regs + TSI721_OBWINUB(obw)); |
| iowrite32((u32)(ob_win->base & TSI721_OBWINLB_BA) | TSI721_OBWINLB_WEN, |
| priv->regs + TSI721_OBWINLB(obw)); |
| |
| *laddr = ob_win->base; |
| return 0; |
| } |
| |
| static void tsi721_unmap_outb_win(struct rio_mport *mport, |
| u16 destid, u64 rstart) |
| { |
| struct tsi721_device *priv = mport->priv; |
| struct tsi721_ob_win *ob_win; |
| int i; |
| |
| tsi_debug(OBW, &priv->pdev->dev, "did=%d ra=0x%llx", destid, rstart); |
| |
| for (i = 0; i < TSI721_OBWIN_NUM; i++) { |
| ob_win = &priv->ob_win[i]; |
| |
| if (ob_win->active && |
| ob_win->destid == destid && ob_win->rstart == rstart) { |
| tsi_debug(OBW, &priv->pdev->dev, |
| "free OBW%d @%llx", i, ob_win->base); |
| ob_win->active = false; |
| iowrite32(0, priv->regs + TSI721_OBWINLB(i)); |
| ob_win->pbar->free += ob_win->size; |
| priv->obwin_cnt++; |
| break; |
| } |
| } |
| } |
| |
| /** |
| * tsi721_init_pc2sr_mapping - initializes outbound (PCIe->SRIO) |
| * translation regions. |
| * @priv: pointer to tsi721 private data |
| * |
| * Disables SREP translation regions. |
| */ |
| static void tsi721_init_pc2sr_mapping(struct tsi721_device *priv) |
| { |
| int i, z; |
| u32 rval; |
| |
| /* Disable all PC2SR translation windows */ |
| for (i = 0; i < TSI721_OBWIN_NUM; i++) |
| iowrite32(0, priv->regs + TSI721_OBWINLB(i)); |
| |
| /* Initialize zone lookup tables to avoid ECC errors on reads */ |
| iowrite32(0, priv->regs + TSI721_LUT_DATA0); |
| iowrite32(0, priv->regs + TSI721_LUT_DATA1); |
| iowrite32(0, priv->regs + TSI721_LUT_DATA2); |
| |
| for (i = 0; i < TSI721_OBWIN_NUM; i++) { |
| for (z = 0; z < TSI721_PC2SR_ZONES; z++) { |
| while (ioread32(priv->regs + TSI721_ZONE_SEL) & |
| TSI721_ZONE_SEL_GO) { |
| udelay(1); |
| } |
| rval = TSI721_ZONE_SEL_GO | (i << 3) | z; |
| iowrite32(rval, priv->regs + TSI721_ZONE_SEL); |
| } |
| } |
| |
| if (priv->p2r_bar[0].size == 0 && priv->p2r_bar[1].size == 0) { |
| priv->obwin_cnt = 0; |
| return; |
| } |
| |
| priv->p2r_bar[0].free = priv->p2r_bar[0].size; |
| priv->p2r_bar[1].free = priv->p2r_bar[1].size; |
| |
| for (i = 0; i < TSI721_OBWIN_NUM; i++) |
| priv->ob_win[i].active = false; |
| |
| priv->obwin_cnt = TSI721_OBWIN_NUM; |
| } |
| |
| /** |
| * tsi721_rio_map_inb_mem -- Mapping inbound memory region. |
| * @mport: RapidIO master port |
| * @lstart: Local memory space start address. |
| * @rstart: RapidIO space start address. |
| * @size: The mapping region size. |
| * @flags: Flags for mapping. 0 for using default flags. |
| * |
| * Return: 0 -- Success. |
| * |
| * This function will create the inbound mapping |
| * from rstart to lstart. |
| */ |
| static int tsi721_rio_map_inb_mem(struct rio_mport *mport, dma_addr_t lstart, |
| u64 rstart, u64 size, u32 flags) |
| { |
| struct tsi721_device *priv = mport->priv; |
| int i, avail = -1; |
| u32 regval; |
| struct tsi721_ib_win *ib_win; |
| bool direct = (lstart == rstart); |
| u64 ibw_size; |
| dma_addr_t loc_start; |
| u64 ibw_start; |
| struct tsi721_ib_win_mapping *map = NULL; |
| int ret = -EBUSY; |
| |
| /* Max IBW size supported by HW is 16GB */ |
| if (size > 0x400000000UL) |
| return -EINVAL; |
| |
| if (direct) { |
| /* Calculate minimal acceptable window size and base address */ |
| |
| ibw_size = roundup_pow_of_two(size); |
| ibw_start = lstart & ~(ibw_size - 1); |
| |
| tsi_debug(IBW, &priv->pdev->dev, |
| "Direct (RIO_0x%llx -> PCIe_%pad), size=0x%llx, ibw_start = 0x%llx", |
| rstart, &lstart, size, ibw_start); |
| |
| while ((lstart + size) > (ibw_start + ibw_size)) { |
| ibw_size *= 2; |
| ibw_start = lstart & ~(ibw_size - 1); |
| /* Check for crossing IBW max size 16GB */ |
| if (ibw_size > 0x400000000UL) |
| return -EBUSY; |
| } |
| |
| loc_start = ibw_start; |
| |
| map = kzalloc(sizeof(struct tsi721_ib_win_mapping), GFP_ATOMIC); |
| if (map == NULL) |
| return -ENOMEM; |
| |
| } else { |
| tsi_debug(IBW, &priv->pdev->dev, |
| "Translated (RIO_0x%llx -> PCIe_%pad), size=0x%llx", |
| rstart, &lstart, size); |
| |
| if (!is_power_of_2(size) || size < 0x1000 || |
| ((u64)lstart & (size - 1)) || (rstart & (size - 1))) |
| return -EINVAL; |
| if (priv->ibwin_cnt == 0) |
| return -EBUSY; |
| ibw_start = rstart; |
| ibw_size = size; |
| loc_start = lstart; |
| } |
| |
| /* |
| * Scan for overlapping with active regions and mark the first available |
| * IB window at the same time. |
| */ |
| for (i = 0; i < TSI721_IBWIN_NUM; i++) { |
| ib_win = &priv->ib_win[i]; |
| |
| if (!ib_win->active) { |
| if (avail == -1) { |
| avail = i; |
| ret = 0; |
| } |
| } else if (ibw_start < (ib_win->rstart + ib_win->size) && |
| (ibw_start + ibw_size) > ib_win->rstart) { |
| /* Return error if address translation involved */ |
| if (!direct || ib_win->xlat) { |
| ret = -EFAULT; |
| break; |
| } |
| |
| /* |
| * Direct mappings usually are larger than originally |
| * requested fragments - check if this new request fits |
| * into it. |
| */ |
| if (rstart >= ib_win->rstart && |
| (rstart + size) <= (ib_win->rstart + |
| ib_win->size)) { |
| /* We are in - no further mapping required */ |
| map->lstart = lstart; |
| list_add_tail(&map->node, &ib_win->mappings); |
| return 0; |
| } |
| |
| ret = -EFAULT; |
| break; |
| } |
| } |
| |
| if (ret) |
| goto out; |
| i = avail; |
| |
| /* Sanity check: available IB window must be disabled at this point */ |
| regval = ioread32(priv->regs + TSI721_IBWIN_LB(i)); |
| if (WARN_ON(regval & TSI721_IBWIN_LB_WEN)) { |
| ret = -EIO; |
| goto out; |
| } |
| |
| ib_win = &priv->ib_win[i]; |
| ib_win->active = true; |
| ib_win->rstart = ibw_start; |
| ib_win->lstart = loc_start; |
| ib_win->size = ibw_size; |
| ib_win->xlat = (lstart != rstart); |
| INIT_LIST_HEAD(&ib_win->mappings); |
| |
| /* |
| * When using direct IBW mapping and have larger than requested IBW size |
| * we can have multiple local memory blocks mapped through the same IBW |
| * To handle this situation we maintain list of "clients" for such IBWs. |
| */ |
| if (direct) { |
| map->lstart = lstart; |
| list_add_tail(&map->node, &ib_win->mappings); |
| } |
| |
| iowrite32(TSI721_IBWIN_SIZE(ibw_size) << 8, |
| priv->regs + TSI721_IBWIN_SZ(i)); |
| |
| iowrite32(((u64)loc_start >> 32), priv->regs + TSI721_IBWIN_TUA(i)); |
| iowrite32(((u64)loc_start & TSI721_IBWIN_TLA_ADD), |
| priv->regs + TSI721_IBWIN_TLA(i)); |
| |
| iowrite32(ibw_start >> 32, priv->regs + TSI721_IBWIN_UB(i)); |
| iowrite32((ibw_start & TSI721_IBWIN_LB_BA) | TSI721_IBWIN_LB_WEN, |
| priv->regs + TSI721_IBWIN_LB(i)); |
| |
| priv->ibwin_cnt--; |
| |
| tsi_debug(IBW, &priv->pdev->dev, |
| "Configured IBWIN%d (RIO_0x%llx -> PCIe_%pad), size=0x%llx", |
| i, ibw_start, &loc_start, ibw_size); |
| |
| return 0; |
| out: |
| kfree(map); |
| return ret; |
| } |
| |
| /** |
| * tsi721_rio_unmap_inb_mem -- Unmapping inbound memory region. |
| * @mport: RapidIO master port |
| * @lstart: Local memory space start address. |
| */ |
| static void tsi721_rio_unmap_inb_mem(struct rio_mport *mport, |
| dma_addr_t lstart) |
| { |
| struct tsi721_device *priv = mport->priv; |
| struct tsi721_ib_win *ib_win; |
| int i; |
| |
| tsi_debug(IBW, &priv->pdev->dev, |
| "Unmap IBW mapped to PCIe_%pad", &lstart); |
| |
| /* Search for matching active inbound translation window */ |
| for (i = 0; i < TSI721_IBWIN_NUM; i++) { |
| ib_win = &priv->ib_win[i]; |
| |
| /* Address translating IBWs must to be an exact march */ |
| if (!ib_win->active || |
| (ib_win->xlat && lstart != ib_win->lstart)) |
| continue; |
| |
| if (lstart >= ib_win->lstart && |
| lstart < (ib_win->lstart + ib_win->size)) { |
| |
| if (!ib_win->xlat) { |
| struct tsi721_ib_win_mapping *map; |
| int found = 0; |
| |
| list_for_each_entry(map, |
| &ib_win->mappings, node) { |
| if (map->lstart == lstart) { |
| list_del(&map->node); |
| kfree(map); |
| found = 1; |
| break; |
| } |
| } |
| |
| if (!found) |
| continue; |
| |
| if (!list_empty(&ib_win->mappings)) |
| break; |
| } |
| |
| tsi_debug(IBW, &priv->pdev->dev, "Disable IBWIN_%d", i); |
| iowrite32(0, priv->regs + TSI721_IBWIN_LB(i)); |
| ib_win->active = false; |
| priv->ibwin_cnt++; |
| break; |
| } |
| } |
| |
| if (i == TSI721_IBWIN_NUM) |
| tsi_debug(IBW, &priv->pdev->dev, |
| "IB window mapped to %pad not found", &lstart); |
| } |
| |
| /** |
| * tsi721_init_sr2pc_mapping - initializes inbound (SRIO->PCIe) |
| * translation regions. |
| * @priv: pointer to tsi721 private data |
| * |
| * Disables inbound windows. |
| */ |
| static void tsi721_init_sr2pc_mapping(struct tsi721_device *priv) |
| { |
| int i; |
| |
| /* Disable all SR2PC inbound windows */ |
| for (i = 0; i < TSI721_IBWIN_NUM; i++) |
| iowrite32(0, priv->regs + TSI721_IBWIN_LB(i)); |
| priv->ibwin_cnt = TSI721_IBWIN_NUM; |
| } |
| |
| /* |
| * tsi721_close_sr2pc_mapping - closes all active inbound (SRIO->PCIe) |
| * translation regions. |
| * @priv: pointer to tsi721 device private data |
| */ |
| static void tsi721_close_sr2pc_mapping(struct tsi721_device *priv) |
| { |
| struct tsi721_ib_win *ib_win; |
| int i; |
| |
| /* Disable all active SR2PC inbound windows */ |
| for (i = 0; i < TSI721_IBWIN_NUM; i++) { |
| ib_win = &priv->ib_win[i]; |
| if (ib_win->active) { |
| iowrite32(0, priv->regs + TSI721_IBWIN_LB(i)); |
| ib_win->active = false; |
| } |
| } |
| } |
| |
| /** |
| * tsi721_port_write_init - Inbound port write interface init |
| * @priv: pointer to tsi721 private data |
| * |
| * Initializes inbound port write handler. |
| * Returns: %0 on success or %-ENOMEM on failure. |
| */ |
| static int tsi721_port_write_init(struct tsi721_device *priv) |
| { |
| priv->pw_discard_count = 0; |
| INIT_WORK(&priv->pw_work, tsi721_pw_dpc); |
| spin_lock_init(&priv->pw_fifo_lock); |
| if (kfifo_alloc(&priv->pw_fifo, |
| TSI721_RIO_PW_MSG_SIZE * 32, GFP_KERNEL)) { |
| tsi_err(&priv->pdev->dev, "PW FIFO allocation failed"); |
| return -ENOMEM; |
| } |
| |
| /* Use reliable port-write capture mode */ |
| iowrite32(TSI721_RIO_PW_CTL_PWC_REL, priv->regs + TSI721_RIO_PW_CTL); |
| return 0; |
| } |
| |
| static void tsi721_port_write_free(struct tsi721_device *priv) |
| { |
| kfifo_free(&priv->pw_fifo); |
| } |
| |
| static int tsi721_doorbell_init(struct tsi721_device *priv) |
| { |
| /* Outbound Doorbells do not require any setup. |
| * Tsi721 uses dedicated PCI BAR1 to generate doorbells. |
| * That BAR1 was mapped during the probe routine. |
| */ |
| |
| /* Initialize Inbound Doorbell processing DPC and queue */ |
| priv->db_discard_count = 0; |
| INIT_WORK(&priv->idb_work, tsi721_db_dpc); |
| |
| /* Allocate buffer for inbound doorbells queue */ |
| priv->idb_base = dma_alloc_coherent(&priv->pdev->dev, |
| IDB_QSIZE * TSI721_IDB_ENTRY_SIZE, |
| &priv->idb_dma, GFP_KERNEL); |
| if (!priv->idb_base) |
| return -ENOMEM; |
| |
| tsi_debug(DBELL, &priv->pdev->dev, |
| "Allocated IDB buffer @ %p (phys = %pad)", |
| priv->idb_base, &priv->idb_dma); |
| |
| iowrite32(TSI721_IDQ_SIZE_VAL(IDB_QSIZE), |
| priv->regs + TSI721_IDQ_SIZE(IDB_QUEUE)); |
| iowrite32(((u64)priv->idb_dma >> 32), |
| priv->regs + TSI721_IDQ_BASEU(IDB_QUEUE)); |
| iowrite32(((u64)priv->idb_dma & TSI721_IDQ_BASEL_ADDR), |
| priv->regs + TSI721_IDQ_BASEL(IDB_QUEUE)); |
| /* Enable accepting all inbound doorbells */ |
| iowrite32(0, priv->regs + TSI721_IDQ_MASK(IDB_QUEUE)); |
| |
| iowrite32(TSI721_IDQ_INIT, priv->regs + TSI721_IDQ_CTL(IDB_QUEUE)); |
| |
| iowrite32(0, priv->regs + TSI721_IDQ_RP(IDB_QUEUE)); |
| |
| return 0; |
| } |
| |
| static void tsi721_doorbell_free(struct tsi721_device *priv) |
| { |
| if (priv->idb_base == NULL) |
| return; |
| |
| /* Free buffer allocated for inbound doorbell queue */ |
| dma_free_coherent(&priv->pdev->dev, IDB_QSIZE * TSI721_IDB_ENTRY_SIZE, |
| priv->idb_base, priv->idb_dma); |
| priv->idb_base = NULL; |
| } |
| |
| /** |
| * tsi721_bdma_maint_init - Initialize maintenance request BDMA channel. |
| * @priv: pointer to tsi721 private data |
| * |
| * Initialize BDMA channel allocated for RapidIO maintenance read/write |
| * request generation |
| * |
| * Returns: %0 on success or %-ENOMEM on failure. |
| */ |
| static int tsi721_bdma_maint_init(struct tsi721_device *priv) |
| { |
| struct tsi721_dma_desc *bd_ptr; |
| u64 *sts_ptr; |
| dma_addr_t bd_phys, sts_phys; |
| int sts_size; |
| int bd_num = 2; |
| void __iomem *regs; |
| |
| tsi_debug(MAINT, &priv->pdev->dev, |
| "Init BDMA_%d Maintenance requests", TSI721_DMACH_MAINT); |
| |
| /* |
| * Initialize DMA channel for maintenance requests |
| */ |
| |
| priv->mdma.ch_id = TSI721_DMACH_MAINT; |
| regs = priv->regs + TSI721_DMAC_BASE(TSI721_DMACH_MAINT); |
| |
| /* Allocate space for DMA descriptors */ |
| bd_ptr = dma_alloc_coherent(&priv->pdev->dev, |
| bd_num * sizeof(struct tsi721_dma_desc), |
| &bd_phys, GFP_KERNEL); |
| if (!bd_ptr) |
| return -ENOMEM; |
| |
| priv->mdma.bd_num = bd_num; |
| priv->mdma.bd_phys = bd_phys; |
| priv->mdma.bd_base = bd_ptr; |
| |
| tsi_debug(MAINT, &priv->pdev->dev, "DMA descriptors @ %p (phys = %pad)", |
| bd_ptr, &bd_phys); |
| |
| /* Allocate space for descriptor status FIFO */ |
| sts_size = (bd_num >= TSI721_DMA_MINSTSSZ) ? |
| bd_num : TSI721_DMA_MINSTSSZ; |
| sts_size = roundup_pow_of_two(sts_size); |
| sts_ptr = dma_alloc_coherent(&priv->pdev->dev, |
| sts_size * sizeof(struct tsi721_dma_sts), |
| &sts_phys, GFP_KERNEL); |
| if (!sts_ptr) { |
| /* Free space allocated for DMA descriptors */ |
| dma_free_coherent(&priv->pdev->dev, |
| bd_num * sizeof(struct tsi721_dma_desc), |
| bd_ptr, bd_phys); |
| priv->mdma.bd_base = NULL; |
| return -ENOMEM; |
| } |
| |
| priv->mdma.sts_phys = sts_phys; |
| priv->mdma.sts_base = sts_ptr; |
| priv->mdma.sts_size = sts_size; |
| |
| tsi_debug(MAINT, &priv->pdev->dev, |
| "desc status FIFO @ %p (phys = %pad) size=0x%x", |
| sts_ptr, &sts_phys, sts_size); |
| |
| /* Initialize DMA descriptors ring */ |
| bd_ptr[bd_num - 1].type_id = cpu_to_le32(DTYPE3 << 29); |
| bd_ptr[bd_num - 1].next_lo = cpu_to_le32((u64)bd_phys & |
| TSI721_DMAC_DPTRL_MASK); |
| bd_ptr[bd_num - 1].next_hi = cpu_to_le32((u64)bd_phys >> 32); |
| |
| /* Setup DMA descriptor pointers */ |
| iowrite32(((u64)bd_phys >> 32), regs + TSI721_DMAC_DPTRH); |
| iowrite32(((u64)bd_phys & TSI721_DMAC_DPTRL_MASK), |
| regs + TSI721_DMAC_DPTRL); |
| |
| /* Setup descriptor status FIFO */ |
| iowrite32(((u64)sts_phys >> 32), regs + TSI721_DMAC_DSBH); |
| iowrite32(((u64)sts_phys & TSI721_DMAC_DSBL_MASK), |
| regs + TSI721_DMAC_DSBL); |
| iowrite32(TSI721_DMAC_DSSZ_SIZE(sts_size), |
| regs + TSI721_DMAC_DSSZ); |
| |
| /* Clear interrupt bits */ |
| iowrite32(TSI721_DMAC_INT_ALL, regs + TSI721_DMAC_INT); |
| |
| ioread32(regs + TSI721_DMAC_INT); |
| |
| /* Toggle DMA channel initialization */ |
| iowrite32(TSI721_DMAC_CTL_INIT, regs + TSI721_DMAC_CTL); |
| ioread32(regs + TSI721_DMAC_CTL); |
| udelay(10); |
| |
| return 0; |
| } |
| |
| static int tsi721_bdma_maint_free(struct tsi721_device *priv) |
| { |
| u32 ch_stat; |
| struct tsi721_bdma_maint *mdma = &priv->mdma; |
| void __iomem *regs = priv->regs + TSI721_DMAC_BASE(mdma->ch_id); |
| |
| if (mdma->bd_base == NULL) |
| return 0; |
| |
| /* Check if DMA channel still running */ |
| ch_stat = ioread32(regs + TSI721_DMAC_STS); |
| if (ch_stat & TSI721_DMAC_STS_RUN) |
| return -EFAULT; |
| |
| /* Put DMA channel into init state */ |
| iowrite32(TSI721_DMAC_CTL_INIT, regs + TSI721_DMAC_CTL); |
| |
| /* Free space allocated for DMA descriptors */ |
| dma_free_coherent(&priv->pdev->dev, |
| mdma->bd_num * sizeof(struct tsi721_dma_desc), |
| mdma->bd_base, mdma->bd_phys); |
| mdma->bd_base = NULL; |
| |
| /* Free space allocated for status FIFO */ |
| dma_free_coherent(&priv->pdev->dev, |
| mdma->sts_size * sizeof(struct tsi721_dma_sts), |
| mdma->sts_base, mdma->sts_phys); |
| mdma->sts_base = NULL; |
| return 0; |
| } |
| |
| /* Enable Inbound Messaging Interrupts */ |
| static void |
| tsi721_imsg_interrupt_enable(struct tsi721_device *priv, int ch, |
| u32 inte_mask) |
| { |
| u32 rval; |
| |
| if (!inte_mask) |
| return; |
| |
| /* Clear pending Inbound Messaging interrupts */ |
| iowrite32(inte_mask, priv->regs + TSI721_IBDMAC_INT(ch)); |
| |
| /* Enable Inbound Messaging interrupts */ |
| rval = ioread32(priv->regs + TSI721_IBDMAC_INTE(ch)); |
| iowrite32(rval | inte_mask, priv->regs + TSI721_IBDMAC_INTE(ch)); |
| |
| if (priv->flags & TSI721_USING_MSIX) |
| return; /* Finished if we are in MSI-X mode */ |
| |
| /* |
| * For MSI and INTA interrupt signalling we need to enable next levels |
| */ |
| |
| /* Enable Device Channel Interrupt */ |
| rval = ioread32(priv->regs + TSI721_DEV_CHAN_INTE); |
| iowrite32(rval | TSI721_INT_IMSG_CHAN(ch), |
| priv->regs + TSI721_DEV_CHAN_INTE); |
| } |
| |
| /* Disable Inbound Messaging Interrupts */ |
| static void |
| tsi721_imsg_interrupt_disable(struct tsi721_device *priv, int ch, |
| u32 inte_mask) |
| { |
| u32 rval; |
| |
| if (!inte_mask) |
| return; |
| |
| /* Clear pending Inbound Messaging interrupts */ |
| iowrite32(inte_mask, priv->regs + TSI721_IBDMAC_INT(ch)); |
| |
| /* Disable Inbound Messaging interrupts */ |
| rval = ioread32(priv->regs + TSI721_IBDMAC_INTE(ch)); |
| rval &= ~inte_mask; |
| iowrite32(rval, priv->regs + TSI721_IBDMAC_INTE(ch)); |
| |
| if (priv->flags & TSI721_USING_MSIX) |
| return; /* Finished if we are in MSI-X mode */ |
| |
| /* |
| * For MSI and INTA interrupt signalling we need to disable next levels |
| */ |
| |
| /* Disable Device Channel Interrupt */ |
| rval = ioread32(priv->regs + TSI721_DEV_CHAN_INTE); |
| rval &= ~TSI721_INT_IMSG_CHAN(ch); |
| iowrite32(rval, priv->regs + TSI721_DEV_CHAN_INTE); |
| } |
| |
| /* Enable Outbound Messaging interrupts */ |
| static void |
| tsi721_omsg_interrupt_enable(struct tsi721_device *priv, int ch, |
| u32 inte_mask) |
| { |
| u32 rval; |
| |
| if (!inte_mask) |
| return; |
| |
| /* Clear pending Outbound Messaging interrupts */ |
| iowrite32(inte_mask, priv->regs + TSI721_OBDMAC_INT(ch)); |
| |
| /* Enable Outbound Messaging channel interrupts */ |
| rval = ioread32(priv->regs + TSI721_OBDMAC_INTE(ch)); |
| iowrite32(rval | inte_mask, priv->regs + TSI721_OBDMAC_INTE(ch)); |
| |
| if (priv->flags & TSI721_USING_MSIX) |
| return; /* Finished if we are in MSI-X mode */ |
| |
| /* |
| * For MSI and INTA interrupt signalling we need to enable next levels |
| */ |
| |
| /* Enable Device Channel Interrupt */ |
| rval = ioread32(priv->regs + TSI721_DEV_CHAN_INTE); |
| iowrite32(rval | TSI721_INT_OMSG_CHAN(ch), |
| priv->regs + TSI721_DEV_CHAN_INTE); |
| } |
| |
| /* Disable Outbound Messaging interrupts */ |
| static void |
| tsi721_omsg_interrupt_disable(struct tsi721_device *priv, int ch, |
| u32 inte_mask) |
| { |
| u32 rval; |
| |
| if (!inte_mask) |
| return; |
| |
| /* Clear pending Outbound Messaging interrupts */ |
| iowrite32(inte_mask, priv->regs + TSI721_OBDMAC_INT(ch)); |
| |
| /* Disable Outbound Messaging interrupts */ |
| rval = ioread32(priv->regs + TSI721_OBDMAC_INTE(ch)); |
| rval &= ~inte_mask; |
| iowrite32(rval, priv->regs + TSI721_OBDMAC_INTE(ch)); |
| |
| if (priv->flags & TSI721_USING_MSIX) |
| return; /* Finished if we are in MSI-X mode */ |
| |
| /* |
| * For MSI and INTA interrupt signalling we need to disable next levels |
| */ |
| |
| /* Disable Device Channel Interrupt */ |
| rval = ioread32(priv->regs + TSI721_DEV_CHAN_INTE); |
| rval &= ~TSI721_INT_OMSG_CHAN(ch); |
| iowrite32(rval, priv->regs + TSI721_DEV_CHAN_INTE); |
| } |
| |
| /** |
| * tsi721_add_outb_message - Add message to the Tsi721 outbound message queue |
| * @mport: Master port with outbound message queue |
| * @rdev: Target of outbound message |
| * @mbox: Outbound mailbox |
| * @buffer: Message to add to outbound queue |
| * @len: Length of message |
| * |
| * Returns: %0 on success or -errno value on failure. |
| */ |
| static int |
| tsi721_add_outb_message(struct rio_mport *mport, struct rio_dev *rdev, int mbox, |
| void *buffer, size_t len) |
| { |
| struct tsi721_device *priv = mport->priv; |
| struct tsi721_omsg_desc *desc; |
| u32 tx_slot; |
| unsigned long flags; |
| |
| if (!priv->omsg_init[mbox] || |
| len > TSI721_MSG_MAX_SIZE || len < 8) |
| return -EINVAL; |
| |
| spin_lock_irqsave(&priv->omsg_ring[mbox].lock, flags); |
| |
| tx_slot = priv->omsg_ring[mbox].tx_slot; |
| |
| /* Copy copy message into transfer buffer */ |
| memcpy(priv->omsg_ring[mbox].omq_base[tx_slot], buffer, len); |
| |
| if (len & 0x7) |
| len += 8; |
| |
| /* Build descriptor associated with buffer */ |
| desc = priv->omsg_ring[mbox].omd_base; |
| desc[tx_slot].type_id = cpu_to_le32((DTYPE4 << 29) | rdev->destid); |
| #ifdef TSI721_OMSG_DESC_INT |
| /* Request IOF_DONE interrupt generation for each N-th frame in queue */ |
| if (tx_slot % 4 == 0) |
| desc[tx_slot].type_id |= cpu_to_le32(TSI721_OMD_IOF); |
| #endif |
| desc[tx_slot].msg_info = |
| cpu_to_le32((mport->sys_size << 26) | (mbox << 22) | |
| (0xe << 12) | (len & 0xff8)); |
| desc[tx_slot].bufptr_lo = |
| cpu_to_le32((u64)priv->omsg_ring[mbox].omq_phys[tx_slot] & |
| 0xffffffff); |
| desc[tx_slot].bufptr_hi = |
| cpu_to_le32((u64)priv->omsg_ring[mbox].omq_phys[tx_slot] >> 32); |
| |
| priv->omsg_ring[mbox].wr_count++; |
| |
| /* Go to next descriptor */ |
| if (++priv->omsg_ring[mbox].tx_slot == priv->omsg_ring[mbox].size) { |
| priv->omsg_ring[mbox].tx_slot = 0; |
| /* Move through the ring link descriptor at the end */ |
| priv->omsg_ring[mbox].wr_count++; |
| } |
| |
| mb(); |
| |
| /* Set new write count value */ |
| iowrite32(priv->omsg_ring[mbox].wr_count, |
| priv->regs + TSI721_OBDMAC_DWRCNT(mbox)); |
| ioread32(priv->regs + TSI721_OBDMAC_DWRCNT(mbox)); |
| |
| spin_unlock_irqrestore(&priv->omsg_ring[mbox].lock, flags); |
| |
| return 0; |
| } |
| |
| /** |
| * tsi721_omsg_handler - Outbound Message Interrupt Handler |
| * @priv: pointer to tsi721 private data |
| * @ch: number of OB MSG channel to service |
| * |
| * Services channel interrupts from outbound messaging engine. |
| */ |
| static void tsi721_omsg_handler(struct tsi721_device *priv, int ch) |
| { |
| u32 omsg_int; |
| struct rio_mport *mport = &priv->mport; |
| void *dev_id = NULL; |
| u32 tx_slot = 0xffffffff; |
| int do_callback = 0; |
| |
| spin_lock(&priv->omsg_ring[ch].lock); |
| |
| omsg_int = ioread32(priv->regs + TSI721_OBDMAC_INT(ch)); |
| |
| if (omsg_int & TSI721_OBDMAC_INT_ST_FULL) |
| tsi_info(&priv->pdev->dev, |
| "OB MBOX%d: Status FIFO is full", ch); |
| |
| if (omsg_int & (TSI721_OBDMAC_INT_DONE | TSI721_OBDMAC_INT_IOF_DONE)) { |
| u32 srd_ptr; |
| u64 *sts_ptr, last_ptr = 0, prev_ptr = 0; |
| int i, j; |
| |
| /* |
| * Find last successfully processed descriptor |
| */ |
| |
| /* Check and clear descriptor status FIFO entries */ |
| srd_ptr = priv->omsg_ring[ch].sts_rdptr; |
| sts_ptr = priv->omsg_ring[ch].sts_base; |
| j = srd_ptr * 8; |
| while (sts_ptr[j]) { |
| for (i = 0; i < 8 && sts_ptr[j]; i++, j++) { |
| prev_ptr = last_ptr; |
| last_ptr = le64_to_cpu(sts_ptr[j]); |
| sts_ptr[j] = 0; |
| } |
| |
| ++srd_ptr; |
| srd_ptr %= priv->omsg_ring[ch].sts_size; |
| j = srd_ptr * 8; |
| } |
| |
| if (last_ptr == 0) |
| goto no_sts_update; |
| |
| priv->omsg_ring[ch].sts_rdptr = srd_ptr; |
| iowrite32(srd_ptr, priv->regs + TSI721_OBDMAC_DSRP(ch)); |
| |
| if (!mport->outb_msg[ch].mcback) |
| goto no_sts_update; |
| |
| /* Inform upper layer about transfer completion */ |
| |
| tx_slot = (last_ptr - (u64)priv->omsg_ring[ch].omd_phys)/ |
| sizeof(struct tsi721_omsg_desc); |
| |
| /* |
| * Check if this is a Link Descriptor (LD). |
| * If yes, ignore LD and use descriptor processed |
| * before LD. |
| */ |
| if (tx_slot == priv->omsg_ring[ch].size) { |
| if (prev_ptr) |
| tx_slot = (prev_ptr - |
| (u64)priv->omsg_ring[ch].omd_phys)/ |
| sizeof(struct tsi721_omsg_desc); |
| else |
| goto no_sts_update; |
| } |
| |
| if (tx_slot >= priv->omsg_ring[ch].size) |
| tsi_debug(OMSG, &priv->pdev->dev, |
| "OB_MSG tx_slot=%x > size=%x", |
| tx_slot, priv->omsg_ring[ch].size); |
| WARN_ON(tx_slot >= priv->omsg_ring[ch].size); |
| |
| /* Move slot index to the next message to be sent */ |
| ++tx_slot; |
| if (tx_slot == priv->omsg_ring[ch].size) |
| tx_slot = 0; |
| |
| dev_id = priv->omsg_ring[ch].dev_id; |
| do_callback = 1; |
| } |
| |
| no_sts_update: |
| |
| if (omsg_int & TSI721_OBDMAC_INT_ERROR) { |
| /* |
| * Outbound message operation aborted due to error, |
| * reinitialize OB MSG channel |
| */ |
| |
| tsi_debug(OMSG, &priv->pdev->dev, "OB MSG ABORT ch_stat=%x", |
| ioread32(priv->regs + TSI721_OBDMAC_STS(ch))); |
| |
| iowrite32(TSI721_OBDMAC_INT_ERROR, |
| priv->regs + TSI721_OBDMAC_INT(ch)); |
| iowrite32(TSI721_OBDMAC_CTL_RETRY_THR | TSI721_OBDMAC_CTL_INIT, |
| priv->regs + TSI721_OBDMAC_CTL(ch)); |
| ioread32(priv->regs + TSI721_OBDMAC_CTL(ch)); |
| |
| /* Inform upper level to clear all pending tx slots */ |
| dev_id = priv->omsg_ring[ch].dev_id; |
| tx_slot = priv->omsg_ring[ch].tx_slot; |
| do_callback = 1; |
| |
| /* Synch tx_slot tracking */ |
| iowrite32(priv->omsg_ring[ch].tx_slot, |
| priv->regs + TSI721_OBDMAC_DRDCNT(ch)); |
| ioread32(priv->regs + TSI721_OBDMAC_DRDCNT(ch)); |
| priv->omsg_ring[ch].wr_count = priv->omsg_ring[ch].tx_slot; |
| priv->omsg_ring[ch].sts_rdptr = 0; |
| } |
| |
| /* Clear channel interrupts */ |
| iowrite32(omsg_int, priv->regs + TSI721_OBDMAC_INT(ch)); |
| |
| if (!(priv->flags & TSI721_USING_MSIX)) { |
| u32 ch_inte; |
| |
| /* Re-enable channel interrupts */ |
| ch_inte = ioread32(priv->regs + TSI721_DEV_CHAN_INTE); |
| ch_inte |= TSI721_INT_OMSG_CHAN(ch); |
| iowrite32(ch_inte, priv->regs + TSI721_DEV_CHAN_INTE); |
| } |
| |
| spin_unlock(&priv->omsg_ring[ch].lock); |
| |
| if (mport->outb_msg[ch].mcback && do_callback) |
| mport->outb_msg[ch].mcback(mport, dev_id, ch, tx_slot); |
| } |
| |
| /** |
| * tsi721_open_outb_mbox - Initialize Tsi721 outbound mailbox |
| * @mport: Master port implementing Outbound Messaging Engine |
| * @dev_id: Device specific pointer to pass on event |
| * @mbox: Mailbox to open |
| * @entries: Number of entries in the outbound mailbox ring |
| * |
| * Returns: %0 on success or -errno value on failure. |
| */ |
| static int tsi721_open_outb_mbox(struct rio_mport *mport, void *dev_id, |
| int mbox, int entries) |
| { |
| struct tsi721_device *priv = mport->priv; |
| struct tsi721_omsg_desc *bd_ptr; |
| int i, rc = 0; |
| |
| if ((entries < TSI721_OMSGD_MIN_RING_SIZE) || |
| (entries > (TSI721_OMSGD_RING_SIZE)) || |
| (!is_power_of_2(entries)) || mbox >= RIO_MAX_MBOX) { |
| rc = -EINVAL; |
| goto out; |
| } |
| |
| if ((mbox_sel & (1 << mbox)) == 0) { |
| rc = -ENODEV; |
| goto out; |
| } |
| |
| priv->omsg_ring[mbox].dev_id = dev_id; |
| priv->omsg_ring[mbox].size = entries; |
| priv->omsg_ring[mbox].sts_rdptr = 0; |
| spin_lock_init(&priv->omsg_ring[mbox].lock); |
| |
| /* Outbound Msg Buffer allocation based on |
| the number of maximum descriptor entries */ |
| for (i = 0; i < entries; i++) { |
| priv->omsg_ring[mbox].omq_base[i] = |
| dma_alloc_coherent( |
| &priv->pdev->dev, TSI721_MSG_BUFFER_SIZE, |
| &priv->omsg_ring[mbox].omq_phys[i], |
| GFP_KERNEL); |
| if (priv->omsg_ring[mbox].omq_base[i] == NULL) { |
| tsi_debug(OMSG, &priv->pdev->dev, |
| "ENOMEM for OB_MSG_%d data buffer", mbox); |
| rc = -ENOMEM; |
| goto out_buf; |
| } |
| } |
| |
| /* Outbound message descriptor allocation */ |
| priv->omsg_ring[mbox].omd_base = dma_alloc_coherent( |
| &priv->pdev->dev, |
| (entries + 1) * sizeof(struct tsi721_omsg_desc), |
| &priv->omsg_ring[mbox].omd_phys, GFP_KERNEL); |
| if (priv->omsg_ring[mbox].omd_base == NULL) { |
| tsi_debug(OMSG, &priv->pdev->dev, |
| "ENOMEM for OB_MSG_%d descriptor memory", mbox); |
| rc = -ENOMEM; |
| goto out_buf; |
| } |
| |
| priv->omsg_ring[mbox].tx_slot = 0; |
| |
| /* Outbound message descriptor status FIFO allocation */ |
| priv->omsg_ring[mbox].sts_size = roundup_pow_of_two(entries + 1); |
| priv->omsg_ring[mbox].sts_base = dma_alloc_coherent(&priv->pdev->dev, |
| priv->omsg_ring[mbox].sts_size * sizeof(struct tsi721_dma_sts), |
| &priv->omsg_ring[mbox].sts_phys, |
| GFP_KERNEL); |
| if (priv->omsg_ring[mbox].sts_base == NULL) { |
| tsi_debug(OMSG, &priv->pdev->dev, |
| "ENOMEM for OB_MSG_%d status FIFO", mbox); |
| rc = -ENOMEM; |
| goto out_desc; |
| } |
| |
| /* |
| * Configure Outbound Messaging Engine |
| */ |
| |
| /* Setup Outbound Message descriptor pointer */ |
| iowrite32(((u64)priv->omsg_ring[mbox].omd_phys >> 32), |
| priv->regs + TSI721_OBDMAC_DPTRH(mbox)); |
| iowrite32(((u64)priv->omsg_ring[mbox].omd_phys & |
| TSI721_OBDMAC_DPTRL_MASK), |
| priv->regs + TSI721_OBDMAC_DPTRL(mbox)); |
| |
| /* Setup Outbound Message descriptor status FIFO */ |
| iowrite32(((u64)priv->omsg_ring[mbox].sts_phys >> 32), |
| priv->regs + TSI721_OBDMAC_DSBH(mbox)); |
| iowrite32(((u64)priv->omsg_ring[mbox].sts_phys & |
| TSI721_OBDMAC_DSBL_MASK), |
| priv->regs + TSI721_OBDMAC_DSBL(mbox)); |
| iowrite32(TSI721_DMAC_DSSZ_SIZE(priv->omsg_ring[mbox].sts_size), |
| priv->regs + (u32)TSI721_OBDMAC_DSSZ(mbox)); |
| |
| /* Enable interrupts */ |
| |
| #ifdef CONFIG_PCI_MSI |
| if (priv->flags & TSI721_USING_MSIX) { |
| int idx = TSI721_VECT_OMB0_DONE + mbox; |
| |
| /* Request interrupt service if we are in MSI-X mode */ |
| rc = request_irq(priv->msix[idx].vector, tsi721_omsg_msix, 0, |
| priv->msix[idx].irq_name, (void *)priv); |
| |
| if (rc) { |
| tsi_debug(OMSG, &priv->pdev->dev, |
| "Unable to get MSI-X IRQ for OBOX%d-DONE", |
| mbox); |
| goto out_stat; |
| } |
| |
| idx = TSI721_VECT_OMB0_INT + mbox; |
| rc = request_irq(priv->msix[idx].vector, tsi721_omsg_msix, 0, |
| priv->msix[idx].irq_name, (void *)priv); |
| |
| if (rc) { |
| tsi_debug(OMSG, &priv->pdev->dev, |
| "Unable to get MSI-X IRQ for MBOX%d-INT", mbox); |
| idx = TSI721_VECT_OMB0_DONE + mbox; |
| free_irq(priv->msix[idx].vector, (void *)priv); |
| goto out_stat; |
| } |
| } |
| #endif /* CONFIG_PCI_MSI */ |
| |
| tsi721_omsg_interrupt_enable(priv, mbox, TSI721_OBDMAC_INT_ALL); |
| |
| /* Initialize Outbound Message descriptors ring */ |
| bd_ptr = priv->omsg_ring[mbox].omd_base; |
| bd_ptr[entries].type_id = cpu_to_le32(DTYPE5 << 29); |
| bd_ptr[entries].msg_info = 0; |
| bd_ptr[entries].next_lo = |
| cpu_to_le32((u64)priv->omsg_ring[mbox].omd_phys & |
| TSI721_OBDMAC_DPTRL_MASK); |
| bd_ptr[entries].next_hi = |
| cpu_to_le32((u64)priv->omsg_ring[mbox].omd_phys >> 32); |
| priv->omsg_ring[mbox].wr_count = 0; |
| mb(); |
| |
| /* Initialize Outbound Message engine */ |
| iowrite32(TSI721_OBDMAC_CTL_RETRY_THR | TSI721_OBDMAC_CTL_INIT, |
| priv->regs + TSI721_OBDMAC_CTL(mbox)); |
| ioread32(priv->regs + TSI721_OBDMAC_DWRCNT(mbox)); |
| udelay(10); |
| |
| priv->omsg_init[mbox] = 1; |
| |
| return 0; |
| |
| #ifdef CONFIG_PCI_MSI |
| out_stat: |
| dma_free_coherent(&priv->pdev->dev, |
| priv->omsg_ring[mbox].sts_size * sizeof(struct tsi721_dma_sts), |
| priv->omsg_ring[mbox].sts_base, |
| priv->omsg_ring[mbox].sts_phys); |
| |
| priv->omsg_ring[mbox].sts_base = NULL; |
| #endif /* CONFIG_PCI_MSI */ |
| |
| out_desc: |
| dma_free_coherent(&priv->pdev->dev, |
| (entries + 1) * sizeof(struct tsi721_omsg_desc), |
| priv->omsg_ring[mbox].omd_base, |
| priv->omsg_ring[mbox].omd_phys); |
| |
| priv->omsg_ring[mbox].omd_base = NULL; |
| |
| out_buf: |
| for (i = 0; i < priv->omsg_ring[mbox].size; i++) { |
| if (priv->omsg_ring[mbox].omq_base[i]) { |
| dma_free_coherent(&priv->pdev->dev, |
| TSI721_MSG_BUFFER_SIZE, |
| priv->omsg_ring[mbox].omq_base[i], |
| priv->omsg_ring[mbox].omq_phys[i]); |
| |
| priv->omsg_ring[mbox].omq_base[i] = NULL; |
| } |
| } |
| |
| out: |
| return rc; |
| } |
| |
| /** |
| * tsi721_close_outb_mbox - Close Tsi721 outbound mailbox |
| * @mport: Master port implementing the outbound message unit |
| * @mbox: Mailbox to close |
| */ |
| static void tsi721_close_outb_mbox(struct rio_mport *mport, int mbox) |
| { |
| struct tsi721_device *priv = mport->priv; |
| u32 i; |
| |
| if (!priv->omsg_init[mbox]) |
| return; |
| priv->omsg_init[mbox] = 0; |
| |
| /* Disable Interrupts */ |
| |
| tsi721_omsg_interrupt_disable(priv, mbox, TSI721_OBDMAC_INT_ALL); |
| |
| #ifdef CONFIG_PCI_MSI |
| if (priv->flags & TSI721_USING_MSIX) { |
| free_irq(priv->msix[TSI721_VECT_OMB0_DONE + mbox].vector, |
| (void *)priv); |
| free_irq(priv->msix[TSI721_VECT_OMB0_INT + mbox].vector, |
| (void *)priv); |
| } |
| #endif /* CONFIG_PCI_MSI */ |
| |
| /* Free OMSG Descriptor Status FIFO */ |
| dma_free_coherent(&priv->pdev->dev, |
| priv->omsg_ring[mbox].sts_size * sizeof(struct tsi721_dma_sts), |
| priv->omsg_ring[mbox].sts_base, |
| priv->omsg_ring[mbox].sts_phys); |
| |
| priv->omsg_ring[mbox].sts_base = NULL; |
| |
| /* Free OMSG descriptors */ |
| dma_free_coherent(&priv->pdev->dev, |
| (priv->omsg_ring[mbox].size + 1) * |
| sizeof(struct tsi721_omsg_desc), |
| priv->omsg_ring[mbox].omd_base, |
| priv->omsg_ring[mbox].omd_phys); |
| |
| priv->omsg_ring[mbox].omd_base = NULL; |
| |
| /* Free message buffers */ |
| for (i = 0; i < priv->omsg_ring[mbox].size; i++) { |
| if (priv->omsg_ring[mbox].omq_base[i]) { |
| dma_free_coherent(&priv->pdev->dev, |
| TSI721_MSG_BUFFER_SIZE, |
| priv->omsg_ring[mbox].omq_base[i], |
| priv->omsg_ring[mbox].omq_phys[i]); |
| |
| priv->omsg_ring[mbox].omq_base[i] = NULL; |
| } |
| } |
| } |
| |
| /** |
| * tsi721_imsg_handler - Inbound Message Interrupt Handler |
| * @priv: pointer to tsi721 private data |
| * @ch: inbound message channel number to service |
| * |
| * Services channel interrupts from inbound messaging engine. |
| */ |
| static void tsi721_imsg_handler(struct tsi721_device *priv, int ch) |
| { |
| u32 mbox = ch - 4; |
| u32 imsg_int; |
| struct rio_mport *mport = &priv->mport; |
| |
| spin_lock(&priv->imsg_ring[mbox].lock); |
| |
| imsg_int = ioread32(priv->regs + TSI721_IBDMAC_INT(ch)); |
| |
| if (imsg_int & TSI721_IBDMAC_INT_SRTO) |
| tsi_info(&priv->pdev->dev, "IB MBOX%d SRIO timeout", mbox); |
| |
| if (imsg_int & TSI721_IBDMAC_INT_PC_ERROR) |
| tsi_info(&priv->pdev->dev, "IB MBOX%d PCIe error", mbox); |
| |
| if (imsg_int & TSI721_IBDMAC_INT_FQ_LOW) |
| tsi_info(&priv->pdev->dev, "IB MBOX%d IB free queue low", mbox); |
| |
| /* Clear IB channel interrupts */ |
| iowrite32(imsg_int, priv->regs + TSI721_IBDMAC_INT(ch)); |
| |
| /* If an IB Msg is received notify the upper layer */ |
| if (imsg_int & TSI721_IBDMAC_INT_DQ_RCV && |
| mport->inb_msg[mbox].mcback) |
| mport->inb_msg[mbox].mcback(mport, |
| priv->imsg_ring[mbox].dev_id, mbox, -1); |
| |
| if (!(priv->flags & TSI721_USING_MSIX)) { |
| u32 ch_inte; |
| |
| /* Re-enable channel interrupts */ |
| ch_inte = ioread32(priv->regs + TSI721_DEV_CHAN_INTE); |
| ch_inte |= TSI721_INT_IMSG_CHAN(ch); |
| iowrite32(ch_inte, priv->regs + TSI721_DEV_CHAN_INTE); |
| } |
| |
| spin_unlock(&priv->imsg_ring[mbox].lock); |
| } |
| |
| /** |
| * tsi721_open_inb_mbox - Initialize Tsi721 inbound mailbox |
| * @mport: Master port implementing the Inbound Messaging Engine |
| * @dev_id: Device specific pointer to pass on event |
| * @mbox: Mailbox to open |
| * @entries: Number of entries in the inbound mailbox ring |
| * |
| * Returns: %0 on success or -errno value on failure. |
| */ |
| static int tsi721_open_inb_mbox(struct rio_mport *mport, void *dev_id, |
| int mbox, int entries) |
| { |
| struct tsi721_device *priv = mport->priv; |
| int ch = mbox + 4; |
| int i; |
| u64 *free_ptr; |
| int rc = 0; |
| |
| if ((entries < TSI721_IMSGD_MIN_RING_SIZE) || |
| (entries > TSI721_IMSGD_RING_SIZE) || |
| (!is_power_of_2(entries)) || mbox >= RIO_MAX_MBOX) { |
| rc = -EINVAL; |
| goto out; |
| } |
| |
| if ((mbox_sel & (1 << mbox)) == 0) { |
| rc = -ENODEV; |
| goto out; |
| } |
| |
| /* Initialize IB Messaging Ring */ |
| priv->imsg_ring[mbox].dev_id = dev_id; |
| priv->imsg_ring[mbox].size = entries; |
| priv->imsg_ring[mbox].rx_slot = 0; |
| priv->imsg_ring[mbox].desc_rdptr = 0; |
| priv->imsg_ring[mbox].fq_wrptr = 0; |
| for (i = 0; i < priv->imsg_ring[mbox].size; i++) |
| priv->imsg_ring[mbox].imq_base[i] = NULL; |
| spin_lock_init(&priv->imsg_ring[mbox].lock); |
| |
| /* Allocate buffers for incoming messages */ |
| priv->imsg_ring[mbox].buf_base = |
| dma_alloc_coherent(&priv->pdev->dev, |
| entries * TSI721_MSG_BUFFER_SIZE, |
| &priv->imsg_ring[mbox].buf_phys, |
| GFP_KERNEL); |
| |
| if (priv->imsg_ring[mbox].buf_base == NULL) { |
| tsi_err(&priv->pdev->dev, |
| "Failed to allocate buffers for IB MBOX%d", mbox); |
| rc = -ENOMEM; |
| goto out; |
| } |
| |
| /* Allocate memory for circular free list */ |
| priv->imsg_ring[mbox].imfq_base = |
| dma_alloc_coherent(&priv->pdev->dev, |
| entries * 8, |
| &priv->imsg_ring[mbox].imfq_phys, |
| GFP_KERNEL); |
| |
| if (priv->imsg_ring[mbox].imfq_base == NULL) { |
| tsi_err(&priv->pdev->dev, |
| "Failed to allocate free queue for IB MBOX%d", mbox); |
| rc = -ENOMEM; |
| goto out_buf; |
| } |
| |
| /* Allocate memory for Inbound message descriptors */ |
| priv->imsg_ring[mbox].imd_base = |
| dma_alloc_coherent(&priv->pdev->dev, |
| entries * sizeof(struct tsi721_imsg_desc), |
| &priv->imsg_ring[mbox].imd_phys, GFP_KERNEL); |
| |
| if (priv->imsg_ring[mbox].imd_base == NULL) { |
| tsi_err(&priv->pdev->dev, |
| "Failed to allocate descriptor memory for IB MBOX%d", |
| mbox); |
| rc = -ENOMEM; |
| goto out_dma; |
| } |
| |
| /* Fill free buffer pointer list */ |
| free_ptr = priv->imsg_ring[mbox].imfq_base; |
| for (i = 0; i < entries; i++) |
| free_ptr[i] = cpu_to_le64( |
| (u64)(priv->imsg_ring[mbox].buf_phys) + |
| i * 0x1000); |
| |
| mb(); |
| |
| /* |
| * For mapping of inbound SRIO Messages into appropriate queues we need |
| * to set Inbound Device ID register in the messaging engine. We do it |
| * once when first inbound mailbox is requested. |
| */ |
| if (!(priv->flags & TSI721_IMSGID_SET)) { |
| iowrite32((u32)priv->mport.host_deviceid, |
| priv->regs + TSI721_IB_DEVID); |
| priv->flags |= TSI721_IMSGID_SET; |
| } |
| |
| /* |
| * Configure Inbound Messaging channel (ch = mbox + 4) |
| */ |
| |
| /* Setup Inbound Message free queue */ |
| iowrite32(((u64)priv->imsg_ring[mbox].imfq_phys >> 32), |
| priv->regs + TSI721_IBDMAC_FQBH(ch)); |
| iowrite32(((u64)priv->imsg_ring[mbox].imfq_phys & |
| TSI721_IBDMAC_FQBL_MASK), |
| priv->regs+TSI721_IBDMAC_FQBL(ch)); |
| iowrite32(TSI721_DMAC_DSSZ_SIZE(entries), |
| priv->regs + TSI721_IBDMAC_FQSZ(ch)); |
| |
| /* Setup Inbound Message descriptor queue */ |
| iowrite32(((u64)priv->imsg_ring[mbox].imd_phys >> 32), |
| priv->regs + TSI721_IBDMAC_DQBH(ch)); |
| iowrite32(((u32)priv->imsg_ring[mbox].imd_phys & |
| (u32)TSI721_IBDMAC_DQBL_MASK), |
| priv->regs+TSI721_IBDMAC_DQBL(ch)); |
| iowrite32(TSI721_DMAC_DSSZ_SIZE(entries), |
| priv->regs + TSI721_IBDMAC_DQSZ(ch)); |
| |
| /* Enable interrupts */ |
| |
| #ifdef CONFIG_PCI_MSI |
| if (priv->flags & TSI721_USING_MSIX) { |
| int idx = TSI721_VECT_IMB0_RCV + mbox; |
| |
| /* Request interrupt service if we are in MSI-X mode */ |
| rc = request_irq(priv->msix[idx].vector, tsi721_imsg_msix, 0, |
| priv->msix[idx].irq_name, (void *)priv); |
| |
| if (rc) { |
| tsi_debug(IMSG, &priv->pdev->dev, |
| "Unable to get MSI-X IRQ for IBOX%d-DONE", |
| mbox); |
| goto out_desc; |
| } |
| |
| idx = TSI721_VECT_IMB0_INT + mbox; |
| rc = request_irq(priv->msix[idx].vector, tsi721_imsg_msix, 0, |
| priv->msix[idx].irq_name, (void *)priv); |
| |
| if (rc) { |
| tsi_debug(IMSG, &priv->pdev->dev, |
| "Unable to get MSI-X IRQ for IBOX%d-INT", mbox); |
| free_irq( |
| priv->msix[TSI721_VECT_IMB0_RCV + mbox].vector, |
| (void *)priv); |
| goto out_desc; |
| } |
| } |
| #endif /* CONFIG_PCI_MSI */ |
| |
| tsi721_imsg_interrupt_enable(priv, ch, TSI721_IBDMAC_INT_ALL); |
| |
| /* Initialize Inbound Message Engine */ |
| iowrite32(TSI721_IBDMAC_CTL_INIT, priv->regs + TSI721_IBDMAC_CTL(ch)); |
| ioread32(priv->regs + TSI721_IBDMAC_CTL(ch)); |
| udelay(10); |
| priv->imsg_ring[mbox].fq_wrptr = entries - 1; |
| iowrite32(entries - 1, priv->regs + TSI721_IBDMAC_FQWP(ch)); |
| |
| priv->imsg_init[mbox] = 1; |
| return 0; |
| |
| #ifdef CONFIG_PCI_MSI |
| out_desc: |
| dma_free_coherent(&priv->pdev->dev, |
| priv->imsg_ring[mbox].size * sizeof(struct tsi721_imsg_desc), |
| priv->imsg_ring[mbox].imd_base, |
| priv->imsg_ring[mbox].imd_phys); |
| |
| priv->imsg_ring[mbox].imd_base = NULL; |
| #endif /* CONFIG_PCI_MSI */ |
| |
| out_dma: |
| dma_free_coherent(&priv->pdev->dev, |
| priv->imsg_ring[mbox].size * 8, |
| priv->imsg_ring[mbox].imfq_base, |
| priv->imsg_ring[mbox].imfq_phys); |
| |
| priv->imsg_ring[mbox].imfq_base = NULL; |
| |
| out_buf: |
| dma_free_coherent(&priv->pdev->dev, |
| priv->imsg_ring[mbox].size * TSI721_MSG_BUFFER_SIZE, |
| priv->imsg_ring[mbox].buf_base, |
| priv->imsg_ring[mbox].buf_phys); |
| |
| priv->imsg_ring[mbox].buf_base = NULL; |
| |
| out: |
| return rc; |
| } |
| |
| /** |
| * tsi721_close_inb_mbox - Shut down Tsi721 inbound mailbox |
| * @mport: Master port implementing the Inbound Messaging Engine |
| * @mbox: Mailbox to close |
| */ |
| static void tsi721_close_inb_mbox(struct rio_mport *mport, int mbox) |
| { |
| struct tsi721_device *priv = mport->priv; |
| u32 rx_slot; |
| int ch = mbox + 4; |
| |
| if (!priv->imsg_init[mbox]) /* mbox isn't initialized yet */ |
| return; |
| priv->imsg_init[mbox] = 0; |
| |
| /* Disable Inbound Messaging Engine */ |
| |
| /* Disable Interrupts */ |
| tsi721_imsg_interrupt_disable(priv, ch, TSI721_OBDMAC_INT_MASK); |
| |
| #ifdef CONFIG_PCI_MSI |
| if (priv->flags & TSI721_USING_MSIX) { |
| free_irq(priv->msix[TSI721_VECT_IMB0_RCV + mbox].vector, |
| (void *)priv); |
| free_irq(priv->msix[TSI721_VECT_IMB0_INT + mbox].vector, |
| (void *)priv); |
| } |
| #endif /* CONFIG_PCI_MSI */ |
| |
| /* Clear Inbound Buffer Queue */ |
| for (rx_slot = 0; rx_slot < priv->imsg_ring[mbox].size; rx_slot++) |
| priv->imsg_ring[mbox].imq_base[rx_slot] = NULL; |
| |
| /* Free memory allocated for message buffers */ |
| dma_free_coherent(&priv->pdev->dev, |
| priv->imsg_ring[mbox].size * TSI721_MSG_BUFFER_SIZE, |
| priv->imsg_ring[mbox].buf_base, |
| priv->imsg_ring[mbox].buf_phys); |
| |
| priv->imsg_ring[mbox].buf_base = NULL; |
| |
| /* Free memory allocated for free pointr list */ |
| dma_free_coherent(&priv->pdev->dev, |
| priv->imsg_ring[mbox].size * 8, |
| priv->imsg_ring[mbox].imfq_base, |
| priv->imsg_ring[mbox].imfq_phys); |
| |
| priv->imsg_ring[mbox].imfq_base = NULL; |
| |
| /* Free memory allocated for RX descriptors */ |
| dma_free_coherent(&priv->pdev->dev, |
| priv->imsg_ring[mbox].size * sizeof(struct tsi721_imsg_desc), |
| priv->imsg_ring[mbox].imd_base, |
| priv->imsg_ring[mbox].imd_phys); |
| |
| priv->imsg_ring[mbox].imd_base = NULL; |
| } |
| |
| /** |
| * tsi721_add_inb_buffer - Add buffer to the Tsi721 inbound message queue |
| * @mport: Master port implementing the Inbound Messaging Engine |
| * @mbox: Inbound mailbox number |
| * @buf: Buffer to add to inbound queue |
| * |
| * Returns: %0 on success or -errno value on failure. |
| */ |
| static int tsi721_add_inb_buffer(struct rio_mport *mport, int mbox, void *buf) |
| { |
| struct tsi721_device *priv = mport->priv; |
| u32 rx_slot; |
| int rc = 0; |
| |
| rx_slot = priv->imsg_ring[mbox].rx_slot; |
| if (priv->imsg_ring[mbox].imq_base[rx_slot]) { |
| tsi_err(&priv->pdev->dev, |
| "Error adding inbound buffer %d, buffer exists", |
| rx_slot); |
| rc = -EINVAL; |
| goto out; |
| } |
| |
| priv->imsg_ring[mbox].imq_base[rx_slot] = buf; |
| |
| if (++priv->imsg_ring[mbox].rx_slot == priv->imsg_ring[mbox].size) |
| priv->imsg_ring[mbox].rx_slot = 0; |
| |
| out: |
| return rc; |
| } |
| |
| /** |
| * tsi721_get_inb_message - Fetch inbound message from the Tsi721 MSG Queue |
| * @mport: Master port implementing the Inbound Messaging Engine |
| * @mbox: Inbound mailbox number |
| * |
| * Returns: pointer to the message on success or %NULL on failure. |
| */ |
| static void *tsi721_get_inb_message(struct rio_mport *mport, int mbox) |
| { |
| struct tsi721_device *priv = mport->priv; |
| struct tsi721_imsg_desc *desc; |
| u32 rx_slot; |
| void *rx_virt = NULL; |
| u64 rx_phys; |
| void *buf = NULL; |
| u64 *free_ptr; |
| int ch = mbox + 4; |
| int msg_size; |
| |
| if (!priv->imsg_init[mbox]) |
| return NULL; |
| |
| desc = priv->imsg_ring[mbox].imd_base; |
| desc += priv->imsg_ring[mbox].desc_rdptr; |
| |
| if (!(le32_to_cpu(desc->msg_info) & TSI721_IMD_HO)) |
| goto out; |
| |
| rx_slot = priv->imsg_ring[mbox].rx_slot; |
| while (priv->imsg_ring[mbox].imq_base[rx_slot] == NULL) { |
| if (++rx_slot == priv->imsg_ring[mbox].size) |
| rx_slot = 0; |
| } |
| |
| rx_phys = ((u64)le32_to_cpu(desc->bufptr_hi) << 32) | |
| le32_to_cpu(desc->bufptr_lo); |
| |
| rx_virt = priv->imsg_ring[mbox].buf_base + |
| (rx_phys - (u64)priv->imsg_ring[mbox].buf_phys); |
| |
| buf = priv->imsg_ring[mbox].imq_base[rx_slot]; |
| msg_size = le32_to_cpu(desc->msg_info) & TSI721_IMD_BCOUNT; |
| if (msg_size == 0) |
| msg_size = RIO_MAX_MSG_SIZE; |
| |
| memcpy(buf, rx_virt, msg_size); |
| priv->imsg_ring[mbox].imq_base[rx_slot] = NULL; |
| |
| desc->msg_info &= cpu_to_le32(~TSI721_IMD_HO); |
| if (++priv->imsg_ring[mbox].desc_rdptr == priv->imsg_ring[mbox].size) |
| priv->imsg_ring[mbox].desc_rdptr = 0; |
| |
| iowrite32(priv->imsg_ring[mbox].desc_rdptr, |
| priv->regs + TSI721_IBDMAC_DQRP(ch)); |
| |
| /* Return free buffer into the pointer list */ |
| free_ptr = priv->imsg_ring[mbox].imfq_base; |
| free_ptr[priv->imsg_ring[mbox].fq_wrptr] = cpu_to_le64(rx_phys); |
| |
| if (++priv->imsg_ring[mbox].fq_wrptr == priv->imsg_ring[mbox].size) |
| priv->imsg_ring[mbox].fq_wrptr = 0; |
| |
| iowrite32(priv->imsg_ring[mbox].fq_wrptr, |
| priv->regs + TSI721_IBDMAC_FQWP(ch)); |
| out: |
| return buf; |
| } |
| |
| /** |
| * tsi721_messages_init - Initialization of Messaging Engine |
| * @priv: pointer to tsi721 private data |
| * |
| * Configures Tsi721 messaging engine. |
| * |
| * Returns: %0 |
| */ |
| static int tsi721_messages_init(struct tsi721_device *priv) |
| { |
| int ch; |
| |
| iowrite32(0, priv->regs + TSI721_SMSG_ECC_LOG); |
| iowrite32(0, priv->regs + TSI721_RETRY_GEN_CNT); |
| iowrite32(0, priv->regs + TSI721_RETRY_RX_CNT); |
| |
| /* Set SRIO Message Request/Response Timeout */ |
| iowrite32(TSI721_RQRPTO_VAL, priv->regs + TSI721_RQRPTO); |
| |
| /* Initialize Inbound Messaging Engine Registers */ |
| for (ch = 0; ch < TSI721_IMSG_CHNUM; ch++) { |
| /* Clear interrupt bits */ |
| iowrite32(TSI721_IBDMAC_INT_MASK, |
| priv->regs + TSI721_IBDMAC_INT(ch)); |
| /* Clear Status */ |
| iowrite32(0, priv->regs + TSI721_IBDMAC_STS(ch)); |
| |
| iowrite32(TSI721_SMSG_ECC_COR_LOG_MASK, |
| priv->regs + TSI721_SMSG_ECC_COR_LOG(ch)); |
| iowrite32(TSI721_SMSG_ECC_NCOR_MASK, |
| priv->regs + TSI721_SMSG_ECC_NCOR(ch)); |
| } |
| |
| return 0; |
| } |
| |
| /** |
| * tsi721_query_mport - Fetch inbound message from the Tsi721 MSG Queue |
| * @mport: Master port implementing the Inbound Messaging Engine |
| * @attr: mport device attributes |
| * |
| * Returns: pointer to the message on success or %NULL on failure. |
| */ |
| static int tsi721_query_mport(struct rio_mport *mport, |
| struct rio_mport_attr *attr) |
| { |
| struct tsi721_device *priv = mport->priv; |
| u32 rval; |
| |
| rval = ioread32(priv->regs + 0x100 + RIO_PORT_N_ERR_STS_CSR(0, 0)); |
| if (rval & RIO_PORT_N_ERR_STS_PORT_OK) { |
| rval = ioread32(priv->regs + 0x100 + RIO_PORT_N_CTL2_CSR(0, 0)); |
| attr->link_speed = (rval & RIO_PORT_N_CTL2_SEL_BAUD) >> 28; |
| rval = ioread32(priv->regs + 0x100 + RIO_PORT_N_CTL_CSR(0, 0)); |
| attr->link_width = (rval & RIO_PORT_N_CTL_IPW) >> 27; |
| } else |
| attr->link_speed = RIO_LINK_DOWN; |
| |
| #ifdef CONFIG_RAPIDIO_DMA_ENGINE |
| attr->flags = RIO_MPORT_DMA | RIO_MPORT_DMA_SG; |
| attr->dma_max_sge = 0; |
| attr->dma_max_size = TSI721_BDMA_MAX_BCOUNT; |
| attr->dma_align = 0; |
| #else |
| attr->flags = 0; |
| #endif |
| return 0; |
| } |
| |
| /** |
| * tsi721_disable_ints - disables all device interrupts |
| * @priv: pointer to tsi721 private data |
| */ |
| static void tsi721_disable_ints(struct tsi721_device *priv) |
| { |
| int ch; |
| |
| /* Disable all device level interrupts */ |
| iowrite32(0, priv->regs + TSI721_DEV_INTE); |
| |
| /* Disable all Device Channel interrupts */ |
| iowrite32(0, priv->regs + TSI721_DEV_CHAN_INTE); |
| |
| /* Disable all Inbound Msg Channel interrupts */ |
| for (ch = 0; ch < TSI721_IMSG_CHNUM; ch++) |
| iowrite32(0, priv->regs + TSI721_IBDMAC_INTE(ch)); |
| |
| /* Disable all Outbound Msg Channel interrupts */ |
| for (ch = 0; ch < TSI721_OMSG_CHNUM; ch++) |
| iowrite32(0, priv->regs + TSI721_OBDMAC_INTE(ch)); |
| |
| /* Disable all general messaging interrupts */ |
| iowrite32(0, priv->regs + TSI721_SMSG_INTE); |
| |
| /* Disable all BDMA Channel interrupts */ |
| for (ch = 0; ch < TSI721_DMA_MAXCH; ch++) |
| iowrite32(0, |
| priv->regs + TSI721_DMAC_BASE(ch) + TSI721_DMAC_INTE); |
| |
| /* Disable all general BDMA interrupts */ |
| iowrite32(0, priv->regs + TSI721_BDMA_INTE); |
| |
| /* Disable all SRIO Channel interrupts */ |
| for (ch = 0; ch < TSI721_SRIO_MAXCH; ch++) |
| iowrite32(0, priv->regs + TSI721_SR_CHINTE(ch)); |
| |
| /* Disable all general SR2PC interrupts */ |
| iowrite32(0, priv->regs + TSI721_SR2PC_GEN_INTE); |
| |
| /* Disable all PC2SR interrupts */ |
| iowrite32(0, priv->regs + TSI721_PC2SR_INTE); |
| |
| /* Disable all I2C interrupts */ |
| iowrite32(0, priv->regs + TSI721_I2C_INT_ENABLE); |
| |
| /* Disable SRIO MAC interrupts */ |
| iowrite32(0, priv->regs + TSI721_RIO_EM_INT_ENABLE); |
| iowrite32(0, priv->regs + TSI721_RIO_EM_DEV_INT_EN); |
| } |
| |
| static struct rio_ops tsi721_rio_ops = { |
| .lcread = tsi721_lcread, |
| .lcwrite = tsi721_lcwrite, |
| .cread = tsi721_cread_dma, |
| .cwrite = tsi721_cwrite_dma, |
| .dsend = tsi721_dsend, |
| .open_inb_mbox = tsi721_open_inb_mbox, |
| .close_inb_mbox = tsi721_close_inb_mbox, |
| .open_outb_mbox = tsi721_open_outb_mbox, |
| .close_outb_mbox = tsi721_close_outb_mbox, |
| .add_outb_message = tsi721_add_outb_message, |
| .add_inb_buffer = tsi721_add_inb_buffer, |
| .get_inb_message = tsi721_get_inb_message, |
| .map_inb = tsi721_rio_map_inb_mem, |
| .unmap_inb = tsi721_rio_unmap_inb_mem, |
| .pwenable = tsi721_pw_enable, |
| .query_mport = tsi721_query_mport, |
| .map_outb = tsi721_map_outb_win, |
| .unmap_outb = tsi721_unmap_outb_win, |
| }; |
| |
| static void tsi721_mport_release(struct device *dev) |
| { |
| struct rio_mport *mport = to_rio_mport(dev); |
| |
| tsi_debug(EXIT, dev, "%s id=%d", mport->name, mport->id); |
| } |
| |
| /** |
| * tsi721_setup_mport - Setup Tsi721 as RapidIO subsystem master port |
| * @priv: pointer to tsi721 private data |
| * |
| * Configures Tsi721 as RapidIO master port. |
| * |
| * Returns: %0 on success or -errno value on failure. |
| */ |
| static int tsi721_setup_mport(struct tsi721_device *priv) |
| { |
| struct pci_dev *pdev = priv->pdev; |
| int err = 0; |
| struct rio_mport *mport = &priv->mport; |
| |
| err = rio_mport_initialize(mport); |
| if (err) |
| return err; |
| |
| mport->ops = &tsi721_rio_ops; |
| mport->index = 0; |
| mport->sys_size = 0; /* small system */ |
| mport->priv = (void *)priv; |
| mport->phys_efptr = 0x100; |
| mport->phys_rmap = 1; |
| mport->dev.parent = &pdev->dev; |
| mport->dev.release = tsi721_mport_release; |
| |
| INIT_LIST_HEAD(&mport->dbells); |
| |
| rio_init_dbell_res(&mport->riores[RIO_DOORBELL_RESOURCE], 0, 0xffff); |
| rio_init_mbox_res(&mport->riores[RIO_INB_MBOX_RESOURCE], 0, 3); |
| rio_init_mbox_res(&mport->riores[RIO_OUTB_MBOX_RESOURCE], 0, 3); |
| snprintf(mport->name, RIO_MAX_MPORT_NAME, "%s(%s)", |
| dev_driver_string(&pdev->dev), dev_name(&pdev->dev)); |
| |
| /* Hook up interrupt handler */ |
| |
| #ifdef CONFIG_PCI_MSI |
| if (!tsi721_enable_msix(priv)) |
| priv->flags |= TSI721_USING_MSIX; |
| else if (!pci_enable_msi(pdev)) |
| priv->flags |= TSI721_USING_MSI; |
| else |
| tsi_debug(MPORT, &pdev->dev, |
| "MSI/MSI-X is not available. Using legacy INTx."); |
| #endif /* CONFIG_PCI_MSI */ |
| |
| err = tsi721_request_irq(priv); |
| |
| if (err) { |
| tsi_err(&pdev->dev, "Unable to get PCI IRQ %02X (err=0x%x)", |
| pdev->irq, err); |
| return err; |
| } |
| |
| #ifdef CONFIG_RAPIDIO_DMA_ENGINE |
| err = tsi721_register_dma(priv); |
| if (err) |
| goto err_exit; |
| #endif |
| /* Enable SRIO link */ |
| iowrite32(ioread32(priv->regs + TSI721_DEVCTL) | |
| TSI721_DEVCTL_SRBOOT_CMPL, |
| priv->regs + TSI721_DEVCTL); |
| |
| if (mport->host_deviceid >= 0) |
| iowrite32(RIO_PORT_GEN_HOST | RIO_PORT_GEN_MASTER | |
| RIO_PORT_GEN_DISCOVERED, |
| priv->regs + (0x100 + RIO_PORT_GEN_CTL_CSR)); |
| else |
| iowrite32(0, priv->regs + (0x100 + RIO_PORT_GEN_CTL_CSR)); |
| |
| err = rio_register_mport(mport); |
| if (err) { |
| tsi721_unregister_dma(priv); |
| goto err_exit; |
| } |
| |
| return 0; |
| |
| err_exit: |
| tsi721_free_irq(priv); |
| return err; |
| } |
| |
| static int tsi721_probe(struct pci_dev *pdev, |
| const struct pci_device_id *id) |
| { |
| struct tsi721_device *priv; |
| int err; |
| |
| priv = kzalloc(sizeof(struct tsi721_device), GFP_KERNEL); |
| if (!priv) { |
| err = -ENOMEM; |
| goto err_exit; |
| } |
| |
| err = pci_enable_device(pdev); |
| if (err) { |
| tsi_err(&pdev->dev, "Failed to enable PCI device"); |
| goto err_clean; |
| } |
| |
| priv->pdev = pdev; |
| |
| #ifdef DEBUG |
| { |
| int i; |
| |
| for (i = 0; i < PCI_STD_NUM_BARS; i++) { |
| tsi_debug(INIT, &pdev->dev, "res%d %pR", |
| i, &pdev->resource[i]); |
| } |
| } |
| #endif |
| /* |
| * Verify BAR configuration |
| */ |
| |
| /* BAR_0 (registers) must be 512KB+ in 32-bit address space */ |
| if (!(pci_resource_flags(pdev, BAR_0) & IORESOURCE_MEM) || |
| pci_resource_flags(pdev, BAR_0) & IORESOURCE_MEM_64 || |
| pci_resource_len(pdev, BAR_0) < TSI721_REG_SPACE_SIZE) { |
| tsi_err(&pdev->dev, "Missing or misconfigured CSR BAR0"); |
| err = -ENODEV; |
| goto err_disable_pdev; |
| } |
| |
| /* BAR_1 (outbound doorbells) must be 16MB+ in 32-bit address space */ |
| if (!(pci_resource_flags(pdev, BAR_1) & IORESOURCE_MEM) || |
| pci_resource_flags(pdev, BAR_1) & IORESOURCE_MEM_64 || |
| pci_resource_len(pdev, BAR_1) < TSI721_DB_WIN_SIZE) { |
| tsi_err(&pdev->dev, "Missing or misconfigured Doorbell BAR1"); |
| err = -ENODEV; |
| goto err_disable_pdev; |
| } |
| |
| /* |
| * BAR_2 and BAR_4 (outbound translation) must be in 64-bit PCIe address |
| * space. |
| * NOTE: BAR_2 and BAR_4 are not used by this version of driver. |
| * It may be a good idea to keep them disabled using HW configuration |
| * to save PCI memory space. |
| */ |
| |
| priv->p2r_bar[0].size = priv->p2r_bar[1].size = 0; |
| |
| if (pci_resource_flags(pdev, BAR_2) & IORESOURCE_MEM_64) { |
| if (pci_resource_flags(pdev, BAR_2) & IORESOURCE_PREFETCH) |
| tsi_debug(INIT, &pdev->dev, |
| "Prefetchable OBW BAR2 will not be used"); |
| else { |
| priv->p2r_bar[0].base = pci_resource_start(pdev, BAR_2); |
| priv->p2r_bar[0].size = pci_resource_len(pdev, BAR_2); |
| } |
| } |
| |
| if (pci_resource_flags(pdev, BAR_4) & IORESOURCE_MEM_64) { |
| if (pci_resource_flags(pdev, BAR_4) & IORESOURCE_PREFETCH) |
| tsi_debug(INIT, &pdev->dev, |
| "Prefetchable OBW BAR4 will not be used"); |
| else { |
| priv->p2r_bar[1].base = pci_resource_start(pdev, BAR_4); |
| priv->p2r_bar[1].size = pci_resource_len(pdev, BAR_4); |
| } |
| } |
| |
| err = pci_request_regions(pdev, DRV_NAME); |
| if (err) { |
| tsi_err(&pdev->dev, "Unable to obtain PCI resources"); |
| goto err_disable_pdev; |
| } |
| |
| pci_set_master(pdev); |
| |
| priv->regs = pci_ioremap_bar(pdev, BAR_0); |
| if (!priv->regs) { |
| tsi_err(&pdev->dev, "Unable to map device registers space"); |
| err = -ENOMEM; |
| goto err_free_res; |
| } |
| |
| priv->odb_base = pci_ioremap_bar(pdev, BAR_1); |
| if (!priv->odb_base) { |
| tsi_err(&pdev->dev, "Unable to map outbound doorbells space"); |
| err = -ENOMEM; |
| goto err_unmap_bars; |
| } |
| |
| /* Configure DMA attributes. */ |
| if (dma_set_mask(&pdev->dev, DMA_BIT_MASK(64))) { |
| err = dma_set_mask(&pdev->dev, DMA_BIT_MASK(32)); |
| if (err) { |
| tsi_err(&pdev->dev, "Unable to set DMA mask"); |
| goto err_unmap_bars; |
| } |
| |
| if (dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(32))) |
| tsi_info(&pdev->dev, "Unable to set consistent DMA mask"); |
| } else { |
| err = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(64)); |
| if (err) |
| tsi_info(&pdev->dev, "Unable to set consistent DMA mask"); |
| } |
| |
| BUG_ON(!pci_is_pcie(pdev)); |
| |
| /* Clear "no snoop" and "relaxed ordering" bits. */ |
| pcie_capability_clear_and_set_word(pdev, PCI_EXP_DEVCTL, |
| PCI_EXP_DEVCTL_RELAX_EN | PCI_EXP_DEVCTL_NOSNOOP_EN, 0); |
| |
| /* Override PCIe Maximum Read Request Size setting if requested */ |
| if (pcie_mrrs >= 0) { |
| if (pcie_mrrs <= 5) |
| pcie_capability_clear_and_set_word(pdev, PCI_EXP_DEVCTL, |
| PCI_EXP_DEVCTL_READRQ, pcie_mrrs << 12); |
| else |
| tsi_info(&pdev->dev, |
| "Invalid MRRS override value %d", pcie_mrrs); |
| } |
| |
| /* Set PCIe completion timeout to 1-10ms */ |
| pcie_capability_clear_and_set_word(pdev, PCI_EXP_DEVCTL2, |
| PCI_EXP_DEVCTL2_COMP_TIMEOUT, 0x2); |
| |
| /* |
| * FIXUP: correct offsets of MSI-X tables in the MSI-X Capability Block |
| */ |
| pci_write_config_dword(pdev, TSI721_PCIECFG_EPCTL, 0x01); |
| pci_write_config_dword(pdev, TSI721_PCIECFG_MSIXTBL, |
| TSI721_MSIXTBL_OFFSET); |
| pci_write_config_dword(pdev, TSI721_PCIECFG_MSIXPBA, |
| TSI721_MSIXPBA_OFFSET); |
| pci_write_config_dword(pdev, TSI721_PCIECFG_EPCTL, 0); |
| /* End of FIXUP */ |
| |
| tsi721_disable_ints(priv); |
| |
| tsi721_init_pc2sr_mapping(priv); |
| tsi721_init_sr2pc_mapping(priv); |
| |
| if (tsi721_bdma_maint_init(priv)) { |
| tsi_err(&pdev->dev, "BDMA initialization failed"); |
| err = -ENOMEM; |
| goto err_unmap_bars; |
| } |
| |
| err = tsi721_doorbell_init(priv); |
| if (err) |
| goto err_free_bdma; |
| |
| tsi721_port_write_init(priv); |
| |
| err = tsi721_messages_init(priv); |
| if (err) |
| goto err_free_consistent; |
| |
| err = tsi721_setup_mport(priv); |
| if (err) |
| goto err_free_consistent; |
| |
| pci_set_drvdata(pdev, priv); |
| tsi721_interrupts_init(priv); |
| |
| return 0; |
| |
| err_free_consistent: |
| tsi721_port_write_free(priv); |
| tsi721_doorbell_free(priv); |
| err_free_bdma: |
| tsi721_bdma_maint_free(priv); |
| err_unmap_bars: |
| if (priv->regs) |
| iounmap(priv->regs); |
| if (priv->odb_base) |
| iounmap(priv->odb_base); |
| err_free_res: |
| pci_release_regions(pdev); |
| err_disable_pdev: |
| pci_disable_device(pdev); |
| err_clean: |
| kfree(priv); |
| err_exit: |
| return err; |
| } |
| |
| static void tsi721_remove(struct pci_dev *pdev) |
| { |
| struct tsi721_device *priv = pci_get_drvdata(pdev); |
| |
| tsi_debug(EXIT, &pdev->dev, "enter"); |
| |
| tsi721_disable_ints(priv); |
| tsi721_free_irq(priv); |
| flush_work(&priv->idb_work); |
| flush_work(&priv->pw_work); |
| rio_unregister_mport(&priv->mport); |
| |
| tsi721_unregister_dma(priv); |
| tsi721_bdma_maint_free(priv); |
| tsi721_doorbell_free(priv); |
| tsi721_port_write_free(priv); |
| tsi721_close_sr2pc_mapping(priv); |
| |
| if (priv->regs) |
| iounmap(priv->regs); |
| if (priv->odb_base) |
| iounmap(priv->odb_base); |
| #ifdef CONFIG_PCI_MSI |
| if (priv->flags & TSI721_USING_MSIX) |
| pci_disable_msix(priv->pdev); |
| else if (priv->flags & TSI721_USING_MSI) |
| pci_disable_msi(priv->pdev); |
| #endif |
| pci_release_regions(pdev); |
| pci_disable_device(pdev); |
| pci_set_drvdata(pdev, NULL); |
| kfree(priv); |
| tsi_debug(EXIT, &pdev->dev, "exit"); |
| } |
| |
| static void tsi721_shutdown(struct pci_dev *pdev) |
| { |
| struct tsi721_device *priv = pci_get_drvdata(pdev); |
| |
| tsi_debug(EXIT, &pdev->dev, "enter"); |
| |
| tsi721_disable_ints(priv); |
| tsi721_dma_stop_all(priv); |
| pci_disable_device(pdev); |
| } |
| |
| static const struct pci_device_id tsi721_pci_tbl[] = { |
| { PCI_DEVICE(PCI_VENDOR_ID_IDT, PCI_DEVICE_ID_TSI721) }, |
| { 0, } /* terminate list */ |
| }; |
| |
| MODULE_DEVICE_TABLE(pci, tsi721_pci_tbl); |
| |
| static struct pci_driver tsi721_driver = { |
| .name = "tsi721", |
| .id_table = tsi721_pci_tbl, |
| .probe = tsi721_probe, |
| .remove = tsi721_remove, |
| .shutdown = tsi721_shutdown, |
| }; |
| |
| module_pci_driver(tsi721_driver); |
| |
| MODULE_DESCRIPTION("IDT Tsi721 PCIExpress-to-SRIO bridge driver"); |
| MODULE_AUTHOR("Integrated Device Technology, Inc."); |
| MODULE_LICENSE("GPL"); |