drivers/atm/midway.h - linux - Git at Google

 /* drivers/atm/midway.h - Efficient Networks Midway (SAR) description */

 /* Written 1995-1999 by Werner Almesberger, EPFL LRC/ICA */


 #ifndef DRIVERS_ATM_MIDWAY_H
 #define DRIVERS_ATM_MIDWAY_H


 #define NR_VCI		1024		/* number of VCIs */
 #define NR_VCI_LD	10		/* log2(NR_VCI) */
 #define NR_DMA_RX	512		/* RX DMA queue entries */
 #define NR_DMA_TX	512		/* TX DMA queue entries */
 #define NR_SERVICE	NR_VCI		/* service list size */
 #define NR_CHAN		8		/* number of TX channels */
 #define TS_CLOCK	25000000	/* traffic shaper clock (cell/sec) */

 #define MAP_MAX_SIZE	0x00400000	/* memory window for max config */
 #define EPROM_SIZE	0x00010000
 #define	MEM_VALID	0xffc00000	/* mask base address with this */
 #define PHY_BASE	0x00020000	/* offset of PHY register are */
 #define REG_BASE	0x00040000	/* offset of Midway register area */
 #define RAM_BASE	0x00200000	/* offset of RAM area */
 #define RAM_INCREMENT	0x00020000	/* probe for RAM every 128kB */

 #define MID_VCI_BASE	RAM_BASE
 #define MID_DMA_RX_BASE	(MID_VCI_BASE+NR_VCI*16)
 #define MID_DMA_TX_BASE	(MID_DMA_RX_BASE+NR_DMA_RX*8)
 #define MID_SERVICE_BASE (MID_DMA_TX_BASE+NR_DMA_TX*8)
 #define MID_FREE_BASE	(MID_SERVICE_BASE+NR_SERVICE*4)

 #define MAC_LEN 6 /* atm.h */

 #define MID_MIN_BUF_SIZE (1024)		/*   1 kB is minimum */
 #define MID_MAX_BUF_SIZE (128*1024)	/* 128 kB is maximum */

 #define RX_DESCR_SIZE	1		/* RX PDU descr is 1 longword */
 #define TX_DESCR_SIZE	2		/* TX PDU descr is 2 longwords */
 #define AAL5_TRAILER	(ATM_AAL5_TRAILER/4) /* AAL5 trailer is 2 longwords */

 #define TX_GAP		8		/* TX buffer gap (words) */

 /*
  * Midway Reset/ID
  *
  * All values read-only. Writing to this register resets Midway chip.
  */

 #define MID_RES_ID_MCON	0x00		/* Midway Reset/ID */

 #define MID_ID		0xf0000000	/* Midway version */
 #define MID_SHIFT	24
 #define MID_MOTHER_ID	0x00000700	/* mother board id */
 #define MID_MOTHER_SHIFT 8
 #define MID_CON_TI	0x00000080	/* 0: normal ctrl; 1: SABRE */
 #define MID_CON_SUNI	0x00000040	/* 0: UTOPIA; 1: SUNI */
 #define MID_CON_V6	0x00000020	/* 0: non-pipel UTOPIA (required iff
 					   !CON_SUNI; 1: UTOPIA */
 #define DAUGTHER_ID	0x0000001f	/* daugther board id */

 /*
  * Interrupt Status Acknowledge, Interrupt Status & Interrupt Enable
  */

 #define MID_ISA		0x01		/* Interrupt Status Acknowledge */
 #define MID_IS		0x02		/* Interrupt Status */
 #define MID_IE		0x03		/* Interrupt Enable */

 #define MID_TX_COMPLETE_7 0x00010000	/* channel N completed a PDU */
 #define MID_TX_COMPLETE_6 0x00008000	/* transmission */
 #define MID_TX_COMPLETE_5 0x00004000
 #define MID_TX_COMPLETE_4 0x00002000
 #define MID_TX_COMPLETE_3 0x00001000
 #define MID_TX_COMPLETE_2 0x00000800
 #define MID_TX_COMPLETE_1 0x00000400
 #define MID_TX_COMPLETE_0 0x00000200
 #define MID_TX_COMPLETE	0x0001fe00	/* any TX */
 #define MID_TX_DMA_OVFL	0x00000100	/* DMA to adapter overflow */
 #define MID_TX_IDENT_MISM 0x00000080	/* TX: ident mismatch => halted */
 #define MID_DMA_LERR_ACK 0x00000040	/* LERR - SBus ? */
 #define MID_DMA_ERR_ACK	0x00000020	/* DMA error */
 #define	MID_RX_DMA_COMPLETE 0x00000010	/* DMA to host done */
 #define MID_TX_DMA_COMPLETE 0x00000008	/* DMA from host done */
 #define MID_SERVICE	0x00000004	/* something in service list */
 #define MID_SUNI_INT	0x00000002	/* interrupt from SUNI */
 #define MID_STAT_OVFL	0x00000001	/* statistics overflow */

 /*
  * Master Control/Status
  */

 #define MID_MC_S	0x04

 #define MID_INT_SELECT	0x000001C0	/* Interrupt level (000: off) */
 #define MID_INT_SEL_SHIFT 6
 #define	MID_TX_LOCK_MODE 0x00000020	/* 0: streaming; 1: TX ovfl->lock */
 #define MID_DMA_ENABLE	0x00000010	/* R: 0: disable; 1: enable
 					   W: 0: no change; 1: enable */
 #define MID_TX_ENABLE	0x00000008	/* R: 0: TX disabled; 1: enabled
 					   W: 0: no change; 1: enable */
 #define MID_RX_ENABLE	0x00000004	/* like TX */
 #define MID_WAIT_1MS	0x00000002	/* R: 0: timer not running; 1: running
 					   W: 0: no change; 1: no interrupts
 							       for 1 ms */
 #define MID_WAIT_500US	0x00000001	/* like WAIT_1MS, but 0.5 ms */

 /*
  * Statistics
  *
  * Cleared when reading.
  */

 #define MID_STAT		0x05

 #define MID_VCI_TRASH	0xFFFF0000	/* trashed cells because of VCI mode */
 #define MID_VCI_TRASH_SHIFT 16
 #define MID_OVFL_TRASH	0x0000FFFF	/* trashed cells because of overflow */

 /*
  * Address registers
  */

 #define MID_SERV_WRITE	0x06	/* free pos in service area (R, 10 bits) */
 #define MID_DMA_ADDR	0x07	/* virtual DMA address (R, 32 bits) */
 #define MID_DMA_WR_RX	0x08	/* (RW, 9 bits) */
 #define MID_DMA_RD_RX	0x09
 #define MID_DMA_WR_TX	0x0A
 #define MID_DMA_RD_TX	0x0B

 /*
  * Transmit Place Registers (0x10+4*channel)
  */

 #define MID_TX_PLACE(c)	(0x10+4*(c))

 #define MID_SIZE	0x00003800	/* size, N*256 x 32 bit */
 #define MID_SIZE_SHIFT	11
 #define MID_LOCATION	0x000007FF	/* location in adapter memory (word) */

 #define MID_LOC_SKIP	8		/* 8 bits of location are always zero
 					   (applies to all uses of location) */

 /*
  * Transmit ReadPtr Registers (0x11+4*channel)
  */

 #define MID_TX_RDPTR(c)	(0x11+4*(c))

 #define MID_READ_PTR	0x00007FFF	/* next word for PHY */

 /*
  * Transmit DescrStart Registers (0x12+4*channel)
  */

 #define MID_TX_DESCRSTART(c) (0x12+4*(c))

 #define MID_DESCR_START	0x00007FFF	/* seg buffer being DMAed */

 #define ENI155_MAGIC	0xa54b872d

 struct midway_eprom {
 	unsigned char mac[MAC_LEN],inv_mac[MAC_LEN];
 	unsigned char pad[36];
 	u32 serial,inv_serial;
 	u32 magic,inv_magic;
 };


 /*
  * VCI table entry
  */

 #define MID_VCI_IN_SERVICE	0x00000001	/* set if VCI is currently in
 						   service list */
 #define MID_VCI_SIZE		0x00038000	/* reassembly buffer size,
 						   2*<size> kB */
 #define MID_VCI_SIZE_SHIFT	15
 #define MID_VCI_LOCATION	0x1ffc0000	/* buffer location */
 #define MID_VCI_LOCATION_SHIFT	18
 #define MID_VCI_PTI_MODE	0x20000000	/* 0: trash, 1: preserve */
 #define MID_VCI_MODE		0xc0000000
 #define MID_VCI_MODE_SHIFT	30
 #define MID_VCI_READ		0x00007fff
 #define MID_VCI_READ_SHIFT	0
 #define MID_VCI_DESCR		0x7fff0000
 #define MID_VCI_DESCR_SHIFT	16
 #define MID_VCI_COUNT		0x000007ff
 #define MID_VCI_COUNT_SHIFT	0
 #define MID_VCI_STATE		0x0000c000
 #define MID_VCI_STATE_SHIFT	14
 #define MID_VCI_WRITE		0x7fff0000
 #define MID_VCI_WRITE_SHIFT	16

 #define MID_MODE_TRASH	0
 #define MID_MODE_RAW	1
 #define MID_MODE_AAL5	2

 /*
  * Reassembly buffer descriptor
  */

 #define MID_RED_COUNT		0x000007ff
 #define MID_RED_CRC_ERR		0x00000800
 #define MID_RED_T		0x00001000
 #define MID_RED_CE		0x00010000
 #define MID_RED_CLP		0x01000000
 #define MID_RED_IDEN		0xfe000000
 #define MID_RED_SHIFT		25

 #define MID_RED_RX_ID		0x1b		/* constant identifier */

 /*
  * Segmentation buffer descriptor
  */

 #define MID_SEG_COUNT		MID_RED_COUNT
 #define MID_SEG_RATE		0x01f80000
 #define MID_SEG_RATE_SHIFT	19
 #define MID_SEG_PR		0x06000000
 #define MID_SEG_PR_SHIFT	25
 #define MID_SEG_AAL5		0x08000000
 #define MID_SEG_ID		0xf0000000
 #define MID_SEG_ID_SHIFT	28
 #define MID_SEG_MAX_RATE	63

 #define MID_SEG_CLP		0x00000001
 #define MID_SEG_PTI		0x0000000e
 #define MID_SEG_PTI_SHIFT	1
 #define MID_SEG_VCI		0x00003ff0
 #define MID_SEG_VCI_SHIFT	4

 #define MID_SEG_TX_ID		0xb		/* constant identifier */

 /*
  * DMA entry
  */

 #define MID_DMA_COUNT		0xffff0000
 #define MID_DMA_COUNT_SHIFT	16
 #define MID_DMA_END		0x00000020
 #define MID_DMA_TYPE		0x0000000f

 #define MID_DT_JK	0x3
 #define MID_DT_WORD	0x0
 #define MID_DT_2W	0x7
 #define MID_DT_4W	0x4
 #define MID_DT_8W	0x5
 #define MID_DT_16W	0x6
 #define MID_DT_2WM	0xf
 #define MID_DT_4WM	0xc
 #define MID_DT_8WM	0xd
 #define MID_DT_16WM	0xe

 /* only for RX*/
 #define MID_DMA_VCI		0x0000ffc0
 #define	MID_DMA_VCI_SHIFT	6

 /* only for TX */
 #define MID_DMA_CHAN		0x000001c0
 #define MID_DMA_CHAN_SHIFT	6

 #define MID_DT_BYTE	0x1
 #define MID_DT_HWORD	0x2

 #endif
	/* drivers/atm/midway.h - Efficient Networks Midway (SAR) description */

	/* Written 1995-1999 by Werner Almesberger, EPFL LRC/ICA */


	#ifndef DRIVERS_ATM_MIDWAY_H
	#define DRIVERS_ATM_MIDWAY_H


	#define NR_VCI 1024 /* number of VCIs */
	#define NR_VCI_LD 10 /* log2(NR_VCI) */
	#define NR_DMA_RX 512 /* RX DMA queue entries */
	#define NR_DMA_TX 512 /* TX DMA queue entries */
	#define NR_SERVICE NR_VCI /* service list size */
	#define NR_CHAN 8 /* number of TX channels */
	#define TS_CLOCK 25000000 /* traffic shaper clock (cell/sec) */

	#define MAP_MAX_SIZE 0x00400000 /* memory window for max config */
	#define EPROM_SIZE 0x00010000
	#define MEM_VALID 0xffc00000 /* mask base address with this */
	#define PHY_BASE 0x00020000 /* offset of PHY register are */
	#define REG_BASE 0x00040000 /* offset of Midway register area */
	#define RAM_BASE 0x00200000 /* offset of RAM area */
	#define RAM_INCREMENT 0x00020000 /* probe for RAM every 128kB */

	#define MID_VCI_BASE RAM_BASE
	#define MID_DMA_RX_BASE (MID_VCI_BASE+NR_VCI*16)
	#define MID_DMA_TX_BASE (MID_DMA_RX_BASE+NR_DMA_RX*8)
	#define MID_SERVICE_BASE (MID_DMA_TX_BASE+NR_DMA_TX*8)
	#define MID_FREE_BASE (MID_SERVICE_BASE+NR_SERVICE*4)

	#define MAC_LEN 6 /* atm.h */

	#define MID_MIN_BUF_SIZE (1024) /* 1 kB is minimum */
	#define MID_MAX_BUF_SIZE (1281024) / 128 kB is maximum */

	#define RX_DESCR_SIZE 1 /* RX PDU descr is 1 longword */
	#define TX_DESCR_SIZE 2 /* TX PDU descr is 2 longwords */
	#define AAL5_TRAILER (ATM_AAL5_TRAILER/4) /* AAL5 trailer is 2 longwords */

	#define TX_GAP 8 /* TX buffer gap (words) */

	/*
	* Midway Reset/ID
	*
	* All values read-only. Writing to this register resets Midway chip.
	*/

	#define MID_RES_ID_MCON 0x00 /* Midway Reset/ID */

	#define MID_ID 0xf0000000 /* Midway version */
	#define MID_SHIFT 24
	#define MID_MOTHER_ID 0x00000700 /* mother board id */
	#define MID_MOTHER_SHIFT 8
	#define MID_CON_TI 0x00000080 /* 0: normal ctrl; 1: SABRE */
	#define MID_CON_SUNI 0x00000040 /* 0: UTOPIA; 1: SUNI */
	#define MID_CON_V6 0x00000020 /* 0: non-pipel UTOPIA (required iff
	!CON_SUNI; 1: UTOPIA */
	#define DAUGTHER_ID 0x0000001f /* daugther board id */

	/*
	* Interrupt Status Acknowledge, Interrupt Status & Interrupt Enable
	*/

	#define MID_ISA 0x01 /* Interrupt Status Acknowledge */
	#define MID_IS 0x02 /* Interrupt Status */
	#define MID_IE 0x03 /* Interrupt Enable */

	#define MID_TX_COMPLETE_7 0x00010000 /* channel N completed a PDU */
	#define MID_TX_COMPLETE_6 0x00008000 /* transmission */
	#define MID_TX_COMPLETE_5 0x00004000
	#define MID_TX_COMPLETE_4 0x00002000
	#define MID_TX_COMPLETE_3 0x00001000
	#define MID_TX_COMPLETE_2 0x00000800
	#define MID_TX_COMPLETE_1 0x00000400
	#define MID_TX_COMPLETE_0 0x00000200
	#define MID_TX_COMPLETE 0x0001fe00 /* any TX */
	#define MID_TX_DMA_OVFL 0x00000100 /* DMA to adapter overflow */
	#define MID_TX_IDENT_MISM 0x00000080 /* TX: ident mismatch => halted */
	#define MID_DMA_LERR_ACK 0x00000040 /* LERR - SBus ? */
	#define MID_DMA_ERR_ACK 0x00000020 /* DMA error */
	#define MID_RX_DMA_COMPLETE 0x00000010 /* DMA to host done */
	#define MID_TX_DMA_COMPLETE 0x00000008 /* DMA from host done */
	#define MID_SERVICE 0x00000004 /* something in service list */
	#define MID_SUNI_INT 0x00000002 /* interrupt from SUNI */
	#define MID_STAT_OVFL 0x00000001 /* statistics overflow */

	/*
	* Master Control/Status
	*/

	#define MID_MC_S 0x04

	#define MID_INT_SELECT 0x000001C0 /* Interrupt level (000: off) */
	#define MID_INT_SEL_SHIFT 6
	#define MID_TX_LOCK_MODE 0x00000020 /* 0: streaming; 1: TX ovfl->lock */
	#define MID_DMA_ENABLE 0x00000010 /* R: 0: disable; 1: enable
	W: 0: no change; 1: enable */
	#define MID_TX_ENABLE 0x00000008 /* R: 0: TX disabled; 1: enabled
	W: 0: no change; 1: enable */
	#define MID_RX_ENABLE 0x00000004 /* like TX */
	#define MID_WAIT_1MS 0x00000002 /* R: 0: timer not running; 1: running
	W: 0: no change; 1: no interrupts
	for 1 ms */
	#define MID_WAIT_500US 0x00000001 /* like WAIT_1MS, but 0.5 ms */

	/*
	* Statistics
	*
	* Cleared when reading.
	*/

	#define MID_STAT 0x05

	#define MID_VCI_TRASH 0xFFFF0000 /* trashed cells because of VCI mode */
	#define MID_VCI_TRASH_SHIFT 16
	#define MID_OVFL_TRASH 0x0000FFFF /* trashed cells because of overflow */

	/*
	* Address registers
	*/

	#define MID_SERV_WRITE 0x06 /* free pos in service area (R, 10 bits) */
	#define MID_DMA_ADDR 0x07 /* virtual DMA address (R, 32 bits) */
	#define MID_DMA_WR_RX 0x08 /* (RW, 9 bits) */
	#define MID_DMA_RD_RX 0x09
	#define MID_DMA_WR_TX 0x0A
	#define MID_DMA_RD_TX 0x0B

	/*
	* Transmit Place Registers (0x10+4*channel)
	*/

	#define MID_TX_PLACE(c) (0x10+4*(c))

	#define MID_SIZE 0x00003800 /* size, N256 x 32 bit /
	#define MID_SIZE_SHIFT 11
	#define MID_LOCATION 0x000007FF /* location in adapter memory (word) */

	#define MID_LOC_SKIP 8 /* 8 bits of location are always zero
	(applies to all uses of location) */

	/*
	* Transmit ReadPtr Registers (0x11+4*channel)
	*/

	#define MID_TX_RDPTR(c) (0x11+4*(c))

	#define MID_READ_PTR 0x00007FFF /* next word for PHY */

	/*
	* Transmit DescrStart Registers (0x12+4*channel)
	*/

	#define MID_TX_DESCRSTART(c) (0x12+4*(c))

	#define MID_DESCR_START 0x00007FFF /* seg buffer being DMAed */

	#define ENI155_MAGIC 0xa54b872d

	struct midway_eprom {
	unsigned char mac[MAC_LEN],inv_mac[MAC_LEN];
	unsigned char pad[36];
	u32 serial,inv_serial;
	u32 magic,inv_magic;
	};


	/*
	* VCI table entry
	*/

	#define MID_VCI_IN_SERVICE 0x00000001 /* set if VCI is currently in
	service list */
	#define MID_VCI_SIZE 0x00038000 /* reassembly buffer size,
	2<size> kB /
	#define MID_VCI_SIZE_SHIFT 15
	#define MID_VCI_LOCATION 0x1ffc0000 /* buffer location */
	#define MID_VCI_LOCATION_SHIFT 18
	#define MID_VCI_PTI_MODE 0x20000000 /* 0: trash, 1: preserve */
	#define MID_VCI_MODE 0xc0000000
	#define MID_VCI_MODE_SHIFT 30
	#define MID_VCI_READ 0x00007fff
	#define MID_VCI_READ_SHIFT 0
	#define MID_VCI_DESCR 0x7fff0000
	#define MID_VCI_DESCR_SHIFT 16
	#define MID_VCI_COUNT 0x000007ff
	#define MID_VCI_COUNT_SHIFT 0
	#define MID_VCI_STATE 0x0000c000
	#define MID_VCI_STATE_SHIFT 14
	#define MID_VCI_WRITE 0x7fff0000
	#define MID_VCI_WRITE_SHIFT 16

	#define MID_MODE_TRASH 0
	#define MID_MODE_RAW 1
	#define MID_MODE_AAL5 2

	/*
	* Reassembly buffer descriptor
	*/

	#define MID_RED_COUNT 0x000007ff
	#define MID_RED_CRC_ERR 0x00000800
	#define MID_RED_T 0x00001000
	#define MID_RED_CE 0x00010000
	#define MID_RED_CLP 0x01000000
	#define MID_RED_IDEN 0xfe000000
	#define MID_RED_SHIFT 25

	#define MID_RED_RX_ID 0x1b /* constant identifier */

	/*
	* Segmentation buffer descriptor
	*/

	#define MID_SEG_COUNT MID_RED_COUNT
	#define MID_SEG_RATE 0x01f80000
	#define MID_SEG_RATE_SHIFT 19
	#define MID_SEG_PR 0x06000000
	#define MID_SEG_PR_SHIFT 25
	#define MID_SEG_AAL5 0x08000000
	#define MID_SEG_ID 0xf0000000
	#define MID_SEG_ID_SHIFT 28
	#define MID_SEG_MAX_RATE 63

	#define MID_SEG_CLP 0x00000001
	#define MID_SEG_PTI 0x0000000e
	#define MID_SEG_PTI_SHIFT 1
	#define MID_SEG_VCI 0x00003ff0
	#define MID_SEG_VCI_SHIFT 4

	#define MID_SEG_TX_ID 0xb /* constant identifier */

	/*
	* DMA entry
	*/

	#define MID_DMA_COUNT 0xffff0000
	#define MID_DMA_COUNT_SHIFT 16
	#define MID_DMA_END 0x00000020
	#define MID_DMA_TYPE 0x0000000f

	#define MID_DT_JK 0x3
	#define MID_DT_WORD 0x0
	#define MID_DT_2W 0x7
	#define MID_DT_4W 0x4
	#define MID_DT_8W 0x5
	#define MID_DT_16W 0x6
	#define MID_DT_2WM 0xf
	#define MID_DT_4WM 0xc
	#define MID_DT_8WM 0xd
	#define MID_DT_16WM 0xe

	/* only for RX*/
	#define MID_DMA_VCI 0x0000ffc0
	#define MID_DMA_VCI_SHIFT 6

	/* only for TX */
	#define MID_DMA_CHAN 0x000001c0
	#define MID_DMA_CHAN_SHIFT 6

	#define MID_DT_BYTE 0x1
	#define MID_DT_HWORD 0x2

	#endif