blob: 1aee3270ce7b9bfcbba6b81f26c9a0045c35210b [file] [log] [blame]
// SPDX-License-Identifier: BSD-3-Clause
/*
* Copyright (c) 2017-2019, The Linux Foundation. All rights reserved.
* Copyright (c) 2019, Linaro Limited
*/
#include <dt-bindings/iio/qcom,spmi-vadc.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/spmi/spmi.h>
/ {
thermal-zones {
pm8150b-thermal {
polling-delay-passive = <100>;
polling-delay = <0>;
thermal-sensors = <&pm8150b_temp>;
trips {
trip0 {
temperature = <95000>;
hysteresis = <0>;
type = "passive";
};
trip1 {
temperature = <115000>;
hysteresis = <0>;
type = "hot";
};
trip2 {
temperature = <145000>;
hysteresis = <0>;
type = "critical";
};
};
};
};
};
&spmi_bus {
pmic@2 {
compatible = "qcom,pm8150b", "qcom,spmi-pmic";
reg = <0x2 SPMI_USID>;
#address-cells = <1>;
#size-cells = <0>;
pon@800 {
compatible = "qcom,pm8916-pon";
reg = <0x0800>;
status = "disabled";
};
pm8150b_vbus: usb-vbus-regulator@1100 {
compatible = "qcom,pm8150b-vbus-reg";
status = "disabled";
reg = <0x1100>;
};
pm8150b_typec: typec@1500 {
compatible = "qcom,pm8150b-typec";
status = "disabled";
reg = <0x1500>,
<0x1700>;
interrupts = <0x2 0x15 0x00 IRQ_TYPE_EDGE_RISING>,
<0x2 0x15 0x01 IRQ_TYPE_EDGE_BOTH>,
<0x2 0x15 0x02 IRQ_TYPE_EDGE_RISING>,
<0x2 0x15 0x03 IRQ_TYPE_EDGE_BOTH>,
<0x2 0x15 0x04 IRQ_TYPE_EDGE_RISING>,
<0x2 0x15 0x05 IRQ_TYPE_EDGE_RISING>,
<0x2 0x15 0x06 IRQ_TYPE_EDGE_BOTH>,
<0x2 0x15 0x07 IRQ_TYPE_EDGE_RISING>,
<0x2 0x17 0x00 IRQ_TYPE_EDGE_RISING>,
<0x2 0x17 0x01 IRQ_TYPE_EDGE_RISING>,
<0x2 0x17 0x02 IRQ_TYPE_EDGE_RISING>,
<0x2 0x17 0x03 IRQ_TYPE_EDGE_RISING>,
<0x2 0x17 0x04 IRQ_TYPE_EDGE_RISING>,
<0x2 0x17 0x05 IRQ_TYPE_EDGE_RISING>,
<0x2 0x17 0x06 IRQ_TYPE_EDGE_RISING>,
<0x2 0x17 0x07 IRQ_TYPE_EDGE_RISING>;
interrupt-names = "or-rid-detect-change",
"vpd-detect",
"cc-state-change",
"vconn-oc",
"vbus-change",
"attach-detach",
"legacy-cable-detect",
"try-snk-src-detect",
"sig-tx",
"sig-rx",
"msg-tx",
"msg-rx",
"msg-tx-failed",
"msg-tx-discarded",
"msg-rx-discarded",
"fr-swap";
vdd-vbus-supply = <&pm8150b_vbus>;
};
pm8150b_temp: temp-alarm@2400 {
compatible = "qcom,spmi-temp-alarm";
reg = <0x2400>;
interrupts = <0x2 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
io-channels = <&pm8150b_adc ADC5_DIE_TEMP>;
io-channel-names = "thermal";
#thermal-sensor-cells = <0>;
};
pm8150b_adc: adc@3100 {
compatible = "qcom,spmi-adc5";
reg = <0x3100>;
#address-cells = <1>;
#size-cells = <0>;
#io-channel-cells = <1>;
interrupts = <0x2 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
channel@0 {
reg = <ADC5_REF_GND>;
qcom,pre-scaling = <1 1>;
label = "ref_gnd";
};
channel@1 {
reg = <ADC5_1P25VREF>;
qcom,pre-scaling = <1 1>;
label = "vref_1p25";
};
channel@6 {
reg = <ADC5_DIE_TEMP>;
qcom,pre-scaling = <1 1>;
label = "die_temp";
};
channel@9 {
reg = <ADC5_CHG_TEMP>;
qcom,pre-scaling = <1 1>;
label = "chg_temp";
};
};
pm8150b_adc_tm: adc-tm@3500 {
compatible = "qcom,spmi-adc-tm5";
reg = <0x3500>;
interrupts = <0x2 0x35 0x0 IRQ_TYPE_EDGE_RISING>;
#thermal-sensor-cells = <1>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
pm8150b_gpios: gpio@c000 {
compatible = "qcom,pm8150b-gpio", "qcom,spmi-gpio";
reg = <0xc000>;
gpio-controller;
gpio-ranges = <&pm8150b_gpios 0 0 12>;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
};
};
pmic@3 {
compatible = "qcom,pm8150b", "qcom,spmi-pmic";
reg = <0x3 SPMI_USID>;
#address-cells = <1>;
#size-cells = <0>;
pm8150b_lpg: pwm {
compatible = "qcom,pm8150b-lpg";
#address-cells = <1>;
#size-cells = <0>;
#pwm-cells = <2>;
status = "disabled";
};
};
};